LINKSYS E1200V2 Wireless-N Router User Manual Linksys E Series Routers User Guide

LINKSYS LLC Wireless-N Router Linksys E Series Routers User Guide

UserManual.wiki >

E1200V2 User Manual

User Manual

User GuideLinksys E-Series Routers

E1200E1500E2500E3200E4200Linksys E-Series

iE1200/E1500 ContentsLinksys E-SeriesiProduct overviewE1200/E1500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1Package contents 1Features 1Back view 2Bottom view 2Setting Up: BasicsHow to create a home network. . . . . . . . . . . . . . . . . . . . . 10What is a network? 10How to set up a home network 10Where to ﬁnd more help . . . . . . . . . . . . . . . . . . . . . . . . . 10How to set up your router . . . . . . . . . . . . . . . . . . . . . . . . 10How to start Cisco Connect 11How to improve your wireless connection speed . . . . . . . . . 12How to test your Internet connection speed . . . . . . . . . . . . 12How to connect devices to your network . . . . . . . . . . . . . . 13How to connect a computer to your network 13How to connect a printer 15How to connect other devices 15How to set up parental controls . . . . . . . . . . . . . . . . . . . . 17How to access parental controls 17How to select the computers to have parental controls 18How to set parental controls 19How to set up guest access to your network . . . . . . . . . . . . 19How to change your router’s name and password. . . . . . . . . 21Setting Up: AdvancedHow to open the browser-based utility . . . . . . . . . . . . . . . 22How to manually set up your router. . . . . . . . . . . . . . . . . . 22How to manually set up your Internet connection 23How to set up the DHCP server on your router . . . . . . . . . . . 25How to set up DHCP reservation 26How to ﬁnd your network on the Internet. . . . . . . . . . . . . . 26How to clone a MAC address . . . . . . . . . . . . . . . . . . . . . . 27How to connect to your corporate oﬃce using a VPN . . . . . . 28How to optimize your router for gaming and voice . . . . . . . . 28How to remotely change your router settings . . . . . . . . . . . 30How to enable Voice over IP on your network . . . . . . . . . . . 31How to conﬁgure UPnP . . . . . . . . . . . . . . . . . . . . . . . . . 31How to use a router as an access point . . . . . . . . . . . . . . . . 31How to put your new router behind an existing router. . . . . . 33To add your router to an existing router or gateway 33To share an Internet connection 33To extend your network 35How to expose a device to the Internet . . . . . . . . . . . . . . . 35Improving SecurityHow do I know if my network is secure? . . . . . . . . . . . . . . . 37Network security following a manual setup. . . . . . . . . . . . . 37How to set up wireless security using Wi-Fi Protected Setup . . 38Wi-Fi Protected Setup activity light 38Connecting a device using the Wi-Fi Protected Setup button 38How to connect a device using its Wi-Fi Protected Setup PIN 39How to connect a device using the router’s Wi-Fi Protected Setup PIN 39E1200/E1500 Contents

iiE1200/E1500 ContentsLinksys E-SeriesHow to connect a device manually 39How to control access to your wireless network . . . . . . . . . . 40How to improve security using the built-in ﬁrewall 41Port Forwarding and Port TriggeringHow to set up port forwarding . . . . . . . . . . . . . . . . . . . . . 51How to set up port forwarding for a single port 51How to set up port forwarding for multiple ports 52How to set up port forwarding for a range of ports 52How to set up port range triggering for online gaming . . . . . 53How to conﬁgure your Xbox for online gaming . . . . . . . . . . 54Maintaining and MonitoringHow to back up and restore your router conﬁguration. . . . . . 55How to restore factory defaults 55How to upgrade the router’s ﬁrmware . . . . . . . . . . . . . . . . 56How to check the status of your router. . . . . . . . . . . . . . . . 57How to disable the Ethernet port status lights 58How to test your Internet connection 59How to conﬁgure and use logs 60Browser-based Utility Menu StructureE1200/E1500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62SpeciﬁcationsLinksys E1200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66Linksys E1500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

iiiE2500 ContentsLinksys E-SeriesiiiE2500 ContentsProduct overviewE2500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Package contents 3Features 3Back view 4Bottom view 4Setting Up: BasicsHow to create a home network. . . . . . . . . . . . . . . . . . . . . 10What is a network? 10How to set up a home network 10Where to ﬁnd more help . . . . . . . . . . . . . . . . . . . . . . . . . 10How to set up your router . . . . . . . . . . . . . . . . . . . . . . . . 10How to start Cisco Connect 11How to improve your wireless connection speed . . . . . . . . . 12How to test your Internet connection speed . . . . . . . . . . . . 12How to connect devices to your network . . . . . . . . . . . . . . 13How to connect a computer to your network 13How to connect a printer 15How to connect other devices 15How to set up parental controls . . . . . . . . . . . . . . . . . . . . 17How to access parental controls 17How to select the computers to have parental controls 18How to set parental controls 19How to set up guest access to your network . . . . . . . . . . . . 19How to change your router’s name and password. . . . . . . . . 21Setting Up: AdvancedHow to open the browser-based utility . . . . . . . . . . . . . . . 22How to manually set up your router. . . . . . . . . . . . . . . . . . 22How to manually set up your Internet connection 23How to get the most out of your dual-band router . . . . . . . . 23How to set up the DHCP server on your router . . . . . . . . . . . 25How to set up DHCP reservation 26How to ﬁnd your network on the Internet. . . . . . . . . . . . . . 26How to clone a MAC address . . . . . . . . . . . . . . . . . . . . . . 27How to connect to your corporate oﬃce using a VPN . . . . . . 28How to optimize your router for gaming and voice . . . . . . . . 28How to remotely change your router settings . . . . . . . . . . . 30How to enable Voice over IP on your network . . . . . . . . . . . 31How to conﬁgure UPnP . . . . . . . . . . . . . . . . . . . . . . . . . 31How to use a router as an access point . . . . . . . . . . . . . . . . 31How to put your new router behind an existing router. . . . . . 33To add your router to an existing router or gateway 33To share an Internet connection 33To extend your network 35How to expose a device to the Internet . . . . . . . . . . . . . . . 35Improving SecurityHow do I know if my network is secure? . . . . . . . . . . . . . . . 37Network security following a manual setup. . . . . . . . . . . . . 37How to set up wireless security using Wi-Fi Protected Setup . . 38Wi-Fi Protected Setup activity light 38

ivE2500 ContentsLinksys E-SeriesConnecting a device using the Wi-Fi Protected Setup button 38How to connect a device using its Wi-Fi Protected Setup PIN 39How to connect a device using the router’s Wi-Fi Protected Setup PIN 39How to connect a device manually 39How to control access to your wireless network . . . . . . . . . . 40How to improve security using the built-in ﬁrewall 41Port Forwarding and Port TriggeringHow to set up port forwarding . . . . . . . . . . . . . . . . . . . . . 51How to set up port forwarding for a single port 51How to set up port forwarding for multiple ports 52How to set up port forwarding for a range of ports 52How to set up port range triggering for online gaming . . . . . 53How to conﬁgure your Xbox for online gaming . . . . . . . . . . 54Maintaining and MonitoringHow to back up and restore your router conﬁguration. . . . . . 55How to restore factory defaults 55How to upgrade the router’s ﬁrmware . . . . . . . . . . . . . . . . 56How to check the status of your router. . . . . . . . . . . . . . . . 57How to disable the Ethernet port status lights 58How to test your Internet connection 59How to conﬁgure and use logs 60Browser-based Utility Menu StructureE2500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63SpeciﬁcationsLinksys E2500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

vE3200 ContentsLinksys E-SeriesvE3200 ContentsProduct overviewE3200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Package contents 5Features 5Back view 6Bottom view 6Setting Up: BasicsHow to create a home network. . . . . . . . . . . . . . . . . . . . . 10What is a network? 10How to set up a home network 10Where to ﬁnd more help . . . . . . . . . . . . . . . . . . . . . . . . . 10How to set up your router . . . . . . . . . . . . . . . . . . . . . . . . 10How to start Cisco Connect 11How to improve your wireless connection speed . . . . . . . . . 12How to test your Internet connection speed . . . . . . . . . . . . 12How to connect devices to your network . . . . . . . . . . . . . . 13How to connect a computer to your network 13How to connect a printer 15How to connect other devices 15How to set up parental controls . . . . . . . . . . . . . . . . . . . . 17How to access parental controls 17How to select the computers to have parental controls 18How to set parental controls 19How to set up guest access to your network . . . . . . . . . . . . 19How to change your router’s name and password. . . . . . . . . 21Setting Up: AdvancedHow to open the browser-based utility . . . . . . . . . . . . . . . 22How to manually set up your router. . . . . . . . . . . . . . . . . . 22How to manually set up your Internet connection 23How to get the most out of your dual-band router . . . . . . . . 23How to set up the DHCP server on your router . . . . . . . . . . . 25How to set up DHCP reservation 26How to ﬁnd your network on the Internet. . . . . . . . . . . . . . 26How to clone a MAC address . . . . . . . . . . . . . . . . . . . . . . 27How to connect to your corporate oﬃce using a VPN . . . . . . 28How to optimize your router for gaming and voice . . . . . . . . 28How to remotely change your router settings . . . . . . . . . . . 30How to enable Voice over IP on your network . . . . . . . . . . . 31How to conﬁgure UPnP . . . . . . . . . . . . . . . . . . . . . . . . . 31How to use a router as an access point . . . . . . . . . . . . . . . . 31How to put your new router behind an existing router. . . . . . 33To add your router to an existing router or gateway 33To share an Internet connection 33To extend your network 35How to expose a device to the Internet . . . . . . . . . . . . . . . 35Improving SecurityHow do I know if my network is secure? . . . . . . . . . . . . . . . 37Network security following a manual setup. . . . . . . . . . . . . 37How to set up wireless security using Wi-Fi Protected Setup . . 38Wi-Fi Protected Setup activity light 38

viE3200 ContentsLinksys E-SeriesConnecting a device using the Wi-Fi Protected Setup button 38How to connect a device using its Wi-Fi Protected Setup PIN 39How to connect a device using the router’s Wi-Fi Protected Setup PIN 39How to connect a device manually 39How to control access to your wireless network . . . . . . . . . . 40How to improve security using the built-in ﬁrewall 41Using an External DriveHow to conﬁgure storage . . . . . . . . . . . . . . . . . . . . . . . . 42How to create shared folders 42How to manage group and user access to shared folders 43How to create a group 43How to create a new user 44How to grant group access to a share 45How to conﬁgure your router’s storage for remote access. . . . 46How to conﬁgure the FTP server 46How to share folders and set access rights 47How to access ﬁles remotely . . . . . . . . . . . . . . . . . . . . . . 48Port Forwarding and Port TriggeringHow to set up port forwarding . . . . . . . . . . . . . . . . . . . . . 51How to set up port forwarding for a single port 51How to set up port forwarding for multiple ports 52How to set up port forwarding for a range of ports 52How to set up port range triggering for online gaming . . . . . 53How to conﬁgure your Xbox for online gaming . . . . . . . . . . 54Maintaining and MonitoringHow to back up and restore your router conﬁguration. . . . . . 55How to restore factory defaults 55How to upgrade the router’s ﬁrmware . . . . . . . . . . . . . . . . 56How to check the status of your router. . . . . . . . . . . . . . . . 57How to disable the Ethernet port status lights 58How to test your Internet connection 59How to conﬁgure and use logs 60Browser-based Utility Menu StructureE3200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64SpeciﬁcationsLinksys E3200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

viiE4200 ContentsLinksys E-SeriesviiProduct overviewE4200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Package contents 7Features 7Top view 8Back view 8Setting Up: BasicsHow to create a home network. . . . . . . . . . . . . . . . . . . . . 10What is a network? 10How to set up a home network 10Where to ﬁnd more help . . . . . . . . . . . . . . . . . . . . . . . . . 10How to set up your router . . . . . . . . . . . . . . . . . . . . . . . . 10How to start Cisco Connect 11How to improve your wireless connection speed . . . . . . . . . 12How to test your Internet connection speed . . . . . . . . . . . . 12How to connect devices to your network . . . . . . . . . . . . . . 13How to connect a computer to your network 13How to connect a printer 15How to connect other devices 15How to set up parental controls . . . . . . . . . . . . . . . . . . . . 17How to access parental controls 17How to select the computers to have parental controls 18How to set parental controls 19How to set up guest access to your network . . . . . . . . . . . . 19How to change your router’s name and password. . . . . . . . . 21Setting Up: AdvancedHow to open the browser-based utility . . . . . . . . . . . . . . . 22How to manually set up your router. . . . . . . . . . . . . . . . . . 22How to manually set up your Internet connection 23How to get the most out of your dual-band router . . . . . . . . 23How to set up the DHCP server on your router . . . . . . . . . . . 25How to set up DHCP reservation 26How to ﬁnd your network on the Internet. . . . . . . . . . . . . . 26How to clone a MAC address . . . . . . . . . . . . . . . . . . . . . . 27How to connect to your corporate oﬃce using a VPN . . . . . . 28How to optimize your router for gaming and voice . . . . . . . . 28How to remotely change your router settings . . . . . . . . . . . 30How to enable Voice over IP on your network . . . . . . . . . . . 31How to conﬁgure UPnP . . . . . . . . . . . . . . . . . . . . . . . . . 31How to use a router as an access point . . . . . . . . . . . . . . . . 31How to put your new router behind an existing router. . . . . . 33To add your router to an existing router or gateway 33To share an Internet connection 33To extend your network 35How to expose a device to the Internet . . . . . . . . . . . . . . . 35Improving SecurityHow do I know if my network is secure? . . . . . . . . . . . . . . . 37Network security following a manual setup. . . . . . . . . . . . . 37How to set up wireless security using Wi-Fi Protected Setup . . 38Wi-Fi Protected Setup activity light 38E4200 Contents

viiiE4200 ContentsLinksys E-SeriesConnecting a device using the Wi-Fi Protected Setup button 38How to connect a device using its Wi-Fi Protected Setup PIN 39How to connect a device using the router’s Wi-Fi Protected Setup PIN 39How to connect a device manually 39How to control access to your wireless network . . . . . . . . . . 40How to improve security using the built-in ﬁrewall 41Using an External DriveHow to conﬁgure storage . . . . . . . . . . . . . . . . . . . . . . . . 42How to create shared folders 42How to manage group and user access to shared folders 43How to create a group 43How to create a new user 44How to grant group access to a share 45How to conﬁgure your router’s storage for remote access. . . . 46How to conﬁgure the FTP server 46How to share folders and set access rights 47How to access ﬁles remotely . . . . . . . . . . . . . . . . . . . . . . 48How to set up your router as a media server . . . . . . . . . . . . 48How to connect your UPnP device to the media server 50Port Forwarding and Port TriggeringHow to set up port forwarding . . . . . . . . . . . . . . . . . . . . . 51How to set up port forwarding for a single port 51How to set up port forwarding for multiple ports 52How to set up port forwarding for a range of ports 52How to set up port range triggering for online gaming . . . . . 53How to conﬁgure your Xbox for online gaming . . . . . . . . . . 54Maintaining and MonitoringHow to back up and restore your router conﬁguration. . . . . . 55How to restore factory defaults 55How to upgrade the router’s ﬁrmware . . . . . . . . . . . . . . . . 56How to check the status of your router. . . . . . . . . . . . . . . . 57How to disable the Ethernet port status lights 58How to test your Internet connection 59How to conﬁgure and use logs 60Browser-based Utility Menu StructureE4200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65SpeciﬁcationsLinksys E4200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

1Product overviewLinksys E-Series1Product overviewE1200/E1500Package contentsIn addition to your router, your router package includes: • Network (Ethernet) cable • AC power adapter • Setup CD containing router setup software and documentationFeaturesWireless-N technologyBuilt with leading 802.11n wireless technology, your router offers maximum speed and range to create an ultra-powerful network designed for home theater performance. Connect your computers, Internet-ready TVs, game consoles, smartphones and other Wi-Fi devices at blazingly fast transfer rates for an unrivaled experience.SpeedBoostHigher quality antenna technology helps maintain high speeds across greater distances throughout your home. (E1500 only; not on E1200)State-of-the-art securityKeep Wi-Fi freeloaders and Internet threats at bay with WPA/WPA2 encryption. An SPI firewall helps keep your network protected.Benefits of Fast EthernetUse the four Fast Ethernet (10/100) ports for quick file sharing between computers and servers.Home network readyConnect computers, printers, and more to your wireless network and the Internet. QoS traffic prioritization technology delivers maximum speed and performance so you can enjoy fast downloads and reliable gaming.Easy to manageCisco Connect software helps you customize your settings and quickly add multiple devices to your network:Separate guest networkCreate a separate, secure, password-protected network for guests.Parental controlsLimit access time and websites with parental controls.

2Product overviewLinksys E-SeriesBack viewEthernet portsWi-Fi Protected Setup buttonInternet portPower portPower indicator • Ethernet ports—Connect Ethernet cables (also called network cables) to these Fast Ethernet (10/100) ports, color coded blue, and to wired Ethernet network devices on your network. • Internet port—Connect an Ethernet cable (also called a network or Internet cable) to this port, color coded yellow, and to your modem.Wi-Fi Protected Setup™ button—Press this button to easily configure wireless security on Wi-Fi Protected Setup-enabled network devices. For more information, see “How to set up wireless security using Wi-Fi Protected Setup” on page 38. • Power indicator—Stays on steadily while power is connected and following a successful Wi-Fi Protected Setup connection. Flashes slowly during bootup, during firmware upgrades, and during a Wi-Fi Protected Setup connection. Flashes quickly when there is a Wi-Fi Protected Setup error. • Power—Connect the included AC power adapter to this port. CAUTIONUse only the adapter that came with your router.Port activity indicatorGreen network activity indicatorNetwork and Internet port • Green activity indicator—On Ethernet ports, stays on when a cable connects the port to another Ethernet port. On the Internet port, stays on while connected to a modem. On both port types, it flashes while transferring data.Bottom view • Reset button—Press and hold this button for 5-10 seconds (until the port lights flash at the same time) to reset the router to its factory defaults. You can also restore the defaults using the browser-based utility. For more information, see “How to restore factory defaults” on page 55.

3Product overviewLinksys E-SeriesE2500Package contentsIn addition to your router, your router package includes: • Network (Ethernet) cable • AC power adapter • Setup CD containing router setup software and documentationFeaturesWireless-N technologyBuilt with leading 802.11n wireless technology, your router offers maximum speed and range to create an ultra-powerful network designed for home theater performance. Connect your computers, Internet-ready TVs, game consoles, smartphones and other Wi-Fi devices at blazingly fast transfer rates for an unrivaled experience.The power of dual bandDouble your network bandwidth with simultaneous dual-band N (2.4 and 5 GHz). The dual-band feature is designed to avoid interference and optimize throughput for smoother and faster HD video streaming, file transfers, and wireless gaming.State-of-the-art securityKeep Wi-Fi freeloaders and Internet threats at bay with WPA/WPA2 encryption. An SPI firewall helps keep your network protected.Benefits of Fast EthernetUse the four Fast Ethernet (10/100) ports for quick file sharing between computers and servers.Network readyConnect computers, printers, scanners, and more to your wireless network and the Internet. QoS traffic prioritization technology delivers maximum speed and performance so you can enjoy fast downloads and reliable VoIP.Easy to manageCisco Connect software helps you customize your settings and quickly add multiple devices to your network:Separate guest networkCreate a separate, secure, password-protected network for guests.Parental controlsLimit access time and websites with parental controls.

4Product overviewLinksys E-SeriesBack viewEthernet ports Wi-Fi Protected Setup buttonInternet portPower portPower indicator • Ethernet ports—Connect Ethernet cables (also called network cables) to these Fast Ethernet (10/100) ports, color coded blue, and to wired Ethernet network devices on your network. • Internet port—Connect an Ethernet cable (also called a network or Internet cable) to this port, color coded yellow, and to your modem.Wi-Fi Protected Setup™ button—Press this button to easily configure wireless security on Wi-Fi Protected Setup-enabled network devices. For more information, see “How to set up wireless security using Wi-Fi Protected Setup” on page 38. • Power indicator—Stays on steadily while power is connected and following a successful Wi-Fi Protected Setup connection. Flashes slowly during bootup, during firmware upgrades, and during a Wi-Fi Protected Setup connection. Flashes quickly when there is a Wi-Fi Protected Setup error. • Power—Connect the included AC power adapter to this port. CAUTIONUse only the adapter that came with your router.Port activity indicatorGreen network activity indicatorNetwork and Internet port • Green activity indicator—On Ethernet ports, stays on when a cable connects the port to another Ethernet port. On the Internet port, stays on while connected to a modem. On both port types, it flashes while transferring data.Bottom view • Reset button—Press and hold this button for 5-10 seconds (until the port lights flash at the same time) to reset the router to its factory defaults. You can also restore the defaults using the browser-based utility. For more information, see “How to restore factory defaults” on page 55.

5Product overviewLinksys E-SeriesE3200Package contentsIn addition to your router, your router package includes: • Network (Ethernet) cable • AC power adapter • Setup CD containing router setup software and documentationFeaturesWireless-N technologyBuilt with leading 802.11n wireless technology, your router offers maximum speed and range to create an ultra-powerful network designed for home theater performance. Connect your computers, Internet-ready TVs, game consoles, smartphones and other Wi-Fi devices at blazingly fast transfer rates.Parental controlsLimit access time and websites with parental controls.The power of dual bandDouble your network bandwidth with simultaneous dual-band N (2.4 and 5 GHz). The dual-band feature is designed to avoid interference and optimize throughput for smoother and faster HD video streaming, file transfers, and wireless gaming.SpeedBoostHigher quality antenna technology helps maintain high speeds across greater distances throughout your home.State-of-the-art securityKeep Wi-Fi freeloaders and Internet threats at bay with WPA/WPA2 encryption. An SPI firewall helps keep your network protected.Benefits of gigabitUse the four Gigabit Ethernet (10/100/1000) ports for quick file sharing (up to 10× faster than standard Ethernet) between other Gigabit-enabled devices like computers and servers.Built-in USB portThe USB port lets you add an external USB drive to your network and share files at home or over the Internet. You can also connect a USB printer and share it across your network.Home theater readyBring the ultimate entertainment experience to your home by connecting computers, Internet-ready TVs, game consoles, media players, and more to your wireless network and the Internet. Simultaneous dual-band N and QoS traffic prioritization technology delivers maximum speed and performance so you can enjoy fast downloads, smooth video and music streaming, and reliable gaming and VoIP.Easy to manageCisco Connect software helps you customize your settings and quickly add multiple devices to your network:Separate guest networkCreate a separate, secure, password-protected network for guests.

6Product overviewLinksys E-SeriesBack viewEthernet ports Wi-Fi Protected Setup buttonInternet portPower portPower indicatorUSB port • USB port—To easily share disk storage with other users on your network or on the Internet, connect a USB drive to this port. For more information, see “Using an External Drive” on page 42. • Ethernet ports—Connect Ethernet cables (also called network cables) to these Gigabit (10/100/1000) ports, color coded blue, and to wired Ethernet network devices on your network. • Internet port—Connect an Ethernet cable (also called a network or Internet cable) to this port, color coded yellow, and to your modem.Wi-Fi Protected Setup™ button—Press this button to easily configure wireless security on Wi-Fi Protected Setup-enabled network devices. For more information, see “How to set up wireless security using Wi-Fi Protected Setup” on page 38. • Power indicator—Stays on steadily while power is connected and following a successful Wi-Fi Protected Setup connection. Flashes slowly during bootup, during firmware upgrades, and during a Wi-Fi Protected Setup connection. Flashes quickly when there is a Wi-Fi Protected Setup error. • Power—Connect the included AC power adapter to this port. CAUTIONUse only the adapter that came with your router.Port activity indicatorsGreen network activity indicatorYellow network activity indicatorNetwork or Internet port • Green network activity indicator—On Ethernet ports, turns on when a cable connects the port to another Gigabit Ethernet port. On the Internet port, turns on while connected to a modem. • Yellow activity indicator—Flashes to indicate network activity over that port.Bottom view • Reset button—Press and hold this button for 5-10 seconds (until the port lights flash at the same time) to reset the router to its factory defaults. You can also restore the defaults using the browser-based utility. For more information, see “How to restore factory defaults” on page 55.

7Product overviewLinksys E-SeriesE4200Package contentsIn addition to your router, your router package includes: • Network (Ethernet) cable • AC power adapter • Setup CD containing router setup software and documentationFeaturesWireless-N technologyBuilt with leading 802.11n wireless technology, your router offers maximum speed and range to create an ultra-powerful network designed for home theater performance. Connect your computers, Internet-ready TVs, game consoles, smartphones and other Wi-Fi devices at blazingly fast transfer rates for an unrivaled experience.The power of dual bandDouble your network bandwidth with simultaneous dual-band N (2.4 and 5 GHz). The dual-band feature is designed to avoid interference and optimize throughput for smoother and faster HD video streaming, file transfers, and wireless gaming.SpeedBoostHigher quality antenna technology helps maintain high speeds across greater distances throughout your home.State-of-the-art securityKeep Wi-Fi freeloaders and Internet threats at bay with WPA/WPA2 encryption. An SPI firewall helps keep your network protected.Benefits of gigabitUse the four Gigabit Ethernet (10/100/1000) ports for quick file sharing (up to 10× faster than standard Ethernet) between other Gigabit-enabled devices like computers and servers.Built-in USB port and UPnP media serverThe USB storage port lets you add an external USB drive to your network and share files at home or over the Internet. It also features a built-in UPnP AV media server for seamless streaming of your video and media files to an Xbox 360, PS3, or other UPnP-compatible device.Home theater readyBring the ultimate entertainment experience to your home by connecting computers, Internet-ready TVs, game consoles, media players, and more to your wireless network and the Internet. Simultaneous dual-band N and QoS traffic prioritization technology delivers maximum speed and performance so you can enjoy fast downloads, smooth video and music streaming, and reliable gaming and VoIP.Quick to installCisco Connect software helps you easily set up your router.

8Product overviewLinksys E-SeriesEasy to manageCisco Connect software helps you customize your settings and quickly add multiple devices to your network:Separate guest networkCreate a separate, secure, password-protected network for guests.Parental controlsLimit access time and websites with parental controls.Top viewIndicator light • Indicator light—Stays on steadily while power is connected and following a successful Wi-Fi Protected Setup connection. Pulses slowly during bootup, during firmware upgrades, and during a Wi-Fi Protected Setup connection. Flashes quickly when there is a Wi-Fi Protected Setup error.Back viewEthernet portsWi-Fi Protected Setup buttonInternet port Power portReset buttonUSB port • Ethernet ports—Connect Ethernet cables (also called network cables) to these Gigabit (10/100/1000) ports, color coded blue, and to wired Ethernet network devices on your network. • Internet port—Connect an Ethernet cable (also called a network or Internet cable) to this port, color coded yellow, and to your modem. • Wi-Fi Protected Setup™ button—Press this button to easily configure wireless security on Wi-Fi Protected Setup-enabled network devices. For more information, see “How to set up wireless security using Wi-Fi Protected Setup” on page 38. • USB port—To easily share disk storage with other users on your network or on the Internet, connect a USB drive to this port. For more information, see “Using an External Drive” on page 42. • Reset button—Press and hold this button for 5-10 seconds (until the port lights flash at the same time) to reset the router to its factory defaults. You can also restore the defaults using the browser-based utility. For more information, see “How to restore factory defaults” on page 55. • Power—Connect the included AC power adapter to this port. CAUTIONUse only the adapter that came with your router.

9Product overviewLinksys E-SeriesPort activity indicatorsGreen network activity indicatorYellow network activity indicatorNetwork or Internet port • Green network activity indicator—On Ethernet ports, turns on when a cable connects the port to another Gigabit Ethernet port. On the Internet port, turns on while connected to a modem. • Yellow network activity indicator—Flashes to indicate network activity over that port.

10Setting Up: BasicsLinksys E-Series10How to create a home networkFor ALLWhat is a network?A network is any group of devices that can communicate with each other. A home network can also include Internet access, which requires a router like this one. A typical home network may include multiple computers, a printer, a modem, and a router. A large home network may also have a switch, additional routers, access points, and many Internet-capable media devices such as TVs, game consoles, and web cameras. • Modem—Connects a computer or a router to your ISP (Internet Service Provider). • Router—Connects your wireless and wired network devices to each other and to the modem (and to your ISP). • Switch—Allows you to connect several wired network devices to your home network. Your router has a built-in network switch (the Ethernet ports). If you have more wired network devices than available Ethernet ports on your router, you will need an additional switch to consolidate the wired connections.How to set up a home network1. Purchase the proper equipment. For a network that includes Internet access, you’ll need: • Computers with an Ethernet port or wireless networking capabilities • A modem for connecting to your ISP (typically supplied by your ISP) • A router to connect your computers with each other and to the modem • Internet service to your home, provided by an ISP (Internet Service Provider)2. Make sure that your modem is working. Your ISP can help you set up your modem and verify that it’s working correctly.3. Set up your router. See “How to set up your router” on page 10.4. To connect a computer or other network device to the network, see “How to connect a computer to your network” on page 13 and “How to connect other devices” on page 15.Where to find more helpFor ALLIn addition to this User Guide, you can find help at these locations: • Linksys.com/support (documentation, downloads, FAQs, technical support, live chat, forums) • Setup CD (Troubleshooting Guide, legal and regulatory notices) • Cisco Connect help (run Cisco Connect, then click Learn More where available) • Browser-based utility context-sensitive help (open the utility, then click Help in the right-side column.)How to set up your routerFor ALLThe easiest and fastest way to set up your router is to run the Cisco Connect setup software. You can find Cisco Connect on the CD that came with your router or download it from the router’s support site at Linksys.com/support. Cisco Connect shows you how to connect your router to your home network, step by step. To get started, see “How to start Cisco Connect” below.If you are an advanced user, you can set up your router manually using the browser-based utility. To get started, see “How to open the browser-based utility” on page 22.Setting Up: Basics

11Setting Up: BasicsLinksys E-SeriesHow to start Cisco ConnectWhen you run the setup CD, Cisco Connect (your router’s setup software) is automatically installed onto your computer. You can then use Cisco Connect to easily manage your router. To install Cisco Connect on another computer after your router has been set up, see “How to install Cisco Connect on another computer” on page 12.NOTES:Your Cisco Connect CD works with only this router model.If you lose your setup CD, you can download the software from Linksys.com/support.To start Cisco Connect for the first time: 1. Insert the CD into your CD or DVD drive.2. Click Set up your Linksys Router.If you do not see this: • For Windows, click Start, Computer, then double-click the CD drive and the Setup icon. • For Mac, double-click the CD icon on your desktop, then double-click the Setup icon.3. Follow the on-screen instructions to complete your router setup. When setup has finished, Cisco Connect has also been installed onto your hard drive.After your router has been set up and Cisco Connect has been installed, you can use Cisco Connect to easily manage many of your router’s settings.To start Cisco Connect on a Windows computer:1. Click Start, All Programs, then click Cisco Connect. The Cisco Connect main menu opens.To start Cisco Connect on a Mac OS X computer:1. Open the Applications folder, then double-click the Cisco Connect icon. The Cisco Connect main menu opens.To install Cisco Connect on another computer:1. See “How to connect a computer using an Easy Setup Key” on page 13. When finished, Cisco Connect has also been installed onto the computer’s hard drive. CAUTIONAfter your router has been set up, do not run the setup CD to install Cisco Connect to another computer. If you run the setup CD again, you will be prompted to enter the router’s network name (SSID) and password.

12Setting Up: BasicsLinksys E-SeriesHow to improve your wireless connection speedFor ALLFollow these tips to improve your network’s wireless connection speed: • Make sure that your router is in a good location: • For the widest coverage area, install your router near the center of your home, and near the ceiling, if possible. • Avoid placing the router on or near metal objects (such as file cabinets and metal furniture), reflective surfaces (such as glass or mirrors), or masonry walls. • Any obstruction can weaken the wireless signal (even non-metallic objects), so the fewer obstructions between the router and the wireless device, the better. • Place the router in a location away from other electronics, motors, and fluorescent lighting. • Many environmental variables can affect the router’s performance, so if your wireless signal is weak, place the router in several locations and test the signal strength to determine the ideal position. • If possible, upgrade wireless network interfaces (such as wireless network cards in computers) from older wireless standards to 802.11n. If a wirelessly networked device uses an older standard, the performance of the entire wireless network may be slower. How to test your Internet connection speedFor ALLTo test your Internet connection speed:1. Run Cisco Connect, then click Change under Router settings. The Router settings screen opens.2. Click Launch Test under Internet Speed. The Internet speed test screen opens.3. Follow the on-screen instructions to complete the test.

13Setting Up: BasicsLinksys E-SeriesHow to connect devices to your networkFor ALLHow to connect a computer to your networkYou can connect a computer to your network using an Easy Setup Key (the easiest way) or manually.How to connect a computer using an Easy Setup KeyTo use an Easy Setup Key, you first need to create one using any available USB drive. After it has been created, you can use the same key to connect several computers to your network.TIPThe Easy Setup Key stores network information (name, password, security type, and security key) so you don’t have to remember them.To create an Easy Setup Key:1. Run Cisco Connect, then click Add device under Computers and devices. The Computers and other devices screen opens.2. Click Computer. 3. Select No, I don’t have an Easy Setup Key, then click Next.4. Insert a USB drive into an available USB port on your computer. This USB drive will be your new Easy Setup Key. Cisco Connect detects the newly attached USB drive and copies the router’s settings and a copy of Cisco Connect to it. 5. When the files have finished copying, remove the Easy Setup Key from your computer. You can now use it to install Cisco Connect onto other computers and to connect them to the network.6. Click Close.

14Setting Up: BasicsLinksys E-SeriesTo use your Easy Setup Key to connect a computer to your network:1. Run Cisco Connect, then click Add device under Computers and devices. The Computers and other devices screen opens.2. Click Computer. 3. Select Yes, I have an Easy Setup Key, then click Next. The Connecting another computer screen opens.4. Insert the Easy Setup Key into an available USB port on the computer that you want to connect to the network. The Connecting another computer screen opens.If you do not see this, use Windows Explorer or Finder to view the Easy Setup Key files, then double-click Connect.5. Click Connect to your router, then follow the on-screen instructions.6. Return to the computer running Cisco Connect, then click Next.7. Enter a name for the newly connected computer, then click Finish.How to connect a computer manuallyTo connect a computer without using an Easy Setup Key, you will need to print or take note of some information.IMPORTANTWhen you manually connect a computer to the network, the computer will not have Cisco Connect installed on it.To manually connect a computer to your network:1. Run Cisco Connect, then click Add device under Computers and devices. The Computers and other devices screen opens.2. Click Computer. 3. Select I want to connect manually using my wireless settings, then click Next. A screen opens that displays network information.4. Write down the Network name (SSID), Security Key, and Security Type information, or click Print these settings if you have a printer attached.5. At the computer you want to connect, enter the network information into your wireless manager.6. After that computer connects to your network, return to the computer running Cisco Connect, then click Next.7. Click Connect to your Linksys router, then follow the on-screen instructions.8. When you are prompted to enter a name for the newly connected computer, enter the name, then click Finish.

15Setting Up: BasicsLinksys E-SeriesHow to connect a printerWhen you install a printer that requires a cable, you can: • Follow the printer’s instructions for setting it up, then follow your computer’s operating system instructions to share the printer with your network.TIPSetting up your printer this way does not require Cisco Connect.- OR - • If your router is a Linksys E3200, you can connect a USB printer to the router’s USB port to make the printer available to any networked computer.When you set up a wireless printer, you need to make sure that: • Your printer has been completely set up except for being connected to the network. • Your printer supports the WPA/WPA2 wireless encryption standard. • If your wireless printer supports WPS (Wi-Fi Protected Setup), you should use WPS to connect it to your network. See “How to set up wireless security using Wi-Fi Protected Setup” on page 38.To connect a wireless printer to your network:1. Run Cisco Connect, then click Add device under Computers and devices. The Computers and other devices screen opens.2. Click Printer, then click Wireless printer. A screen opens that displays network information.3. Write down the Network name (SSID), Security Key, and Security Type information, or click Print these settings if you have a different printer already connected.4. Follow your printer’s instructions for entering the wireless network information into your printer.5. After the printer connects to your network, click Next in Cisco Connect.6. Return to the computer running Cisco Connect, then click Next. The Name your printer screen opens.7. Enter a name for the printer, then click Finish.8. Follow your computer operating system’s instructions for adding the new printer to your list of available printers.To connect a USB printer to your network through the router’s USB port:For E32001. Run Cisco Connect, then click Add device under Computers and devices. The Computers and other devices screen opens.2. Click Printer, then click USB Printer.3. Follow the on-screen instructions for connecting the printer. This process may take several minutes.4. Repeat Steps 1-3 on each computer you want to print from. For information on installing Cisco Connect onto other computers, see “To install Cisco Connect on another computer:” on page 11.How to connect other devicesMany other types of wireless network devices can connect to your home network, including: • Game consoles • Internet-capable TVs and media players • Digital music players • Smart phones

16Setting Up: BasicsLinksys E-SeriesBecause of the wide variety of devices and methods of connecting, you must manually enter network information into the devices for a successful network connection. To manually connect a device to your network:1. Run Cisco Connect, then click Add device under Computers and devices. The Computers and other devices screen opens.2. Click Other wireless devices. A screen opens that displays network information.3. Write down the Network name (SSID), Security Key, and Security Type information, or click Print these settings if you have a printer attached.4. Follow your device’s instructions for entering the wireless network information into the device.5. After the device connects to your network, return to the computer running Cisco Connect, then click Next.6. Enter a name for device, then click Finish.For more instructions on connecting a game console to your network, see also: • “How to optimize your router for gaming and voice” on page 28 • “How to set up port forwarding” on page 51 • “How to set up port range triggering for online gaming” on page 53

17Setting Up: BasicsLinksys E-SeriesHow to set up parental controlsFor ALLWith your router, you can use parental controls to: • Set the times that Internet access is allowed. • Block websites based on their content. • Block websites that you specify. • Set the above restrictions for specific computers.TIPWhen someone tries to open a blocked website, a window opens asking for the parental controls password. Enter the password to view the blocked content.How to access parental controlsThe first time you try to access parental controls, you are asked to set a password.To access parental controls for the first time:1. Run Cisco Connect, then click Change under Parental controls. The Parental controls password screen opens.2. Enter a password (from 4 to 32 characters), then enter a secret question and answer. • The password must contain from 4 to 32 valid characters, which are A-Z, a-z, and 0-9. • The answer to the secret question should be something not easily guessed by others. If you forget your password, you can reset it by correctly answering your secret question.3. To save your settings, click OK. The Parental controls main screen appears.To access parental controls after the first time:1. Run Cisco Connect, then click Change under Parental controls. The Enter the parental controls password screen opens.2. Enter the parental control password, then click OK.NOTEIf you forgot the password, click I forgot my password and enter the answer to your secret question.The Parental controls main screen appears.

18Setting Up: BasicsLinksys E-SeriesTo change the parental controls password:1. In the Parental controls main screen, click Change parental controls password, then follow the on-screen instructions.How to select the computers to have parental controlsIt’s not necessary to set parental controls over each computer on your home network. You can set the controls on only those computers that children can access.To select computers that will have parental controls:1. In the Parental controls main screen, click + (add) under the Restrict Internet access on box.2. Click the computer name, then click OK. The computer is added to the list of computers with parental controls.3. To remove parental controls from a computer, click the computer name in the Restrict Internet access on box, then click – (remove).

19Setting Up: BasicsLinksys E-SeriesHow to set parental controls1. In the Parental controls main screen, click the computer name to set parental controls for.2. Under Block Internet access, specify when the computer’s Internet access will be blocked: • Never does not block Internet access. • Always blocks Internet access at all times. • Specific times blocks Internet access only during specific times. If you select this option, set the schedule for School nights (Monday through Friday) and Weekends (Saturday and Sunday).3. To create or change a list of specific websites to block, click Edit next to Block specific sites. The Block these sites screen opens.a. On a blank line, enter a website address that you want to block.b. Click Save to save the list and return to the Parental controls main screen.4. To save your changes, click Finish.5. Repeat the above steps for each computer that you want to set parental controls for.How to set up guest access to your networkYou can use your router’s guest access feature to provide your guests with access to the Internet, while restricting their access to other resources on your local network. The guest network is shown as an open, unsecure wireless network that your guests can easily connect to. To prevent unauthorized users from using your Internet access, your guest network requires that a password be entered for Internet access. The guest network is enabled by default.web browser - guest access login - Linksys E4200 http://mynetwork/guest/loginEnter the Guest Passwordfor Internet Access:LoginX_DoneFile Edit View Go Shortcuts Options HelpXhttp://mynetwork/guest/loginEnter the Guest Passwordfor Internet Access:LoginGuest NetworkLocal NetworkLocal Access and Guest Access Diagram

20Setting Up: BasicsLinksys E-SeriesTo set up guest access to your network:1. Run Cisco Connect, then click Change under Guest Access. The Guest Access screen opens.2. Under Allow guest access, click yes (default) to allow guest Internet access. Otherwise, click no to disable guest access.3. Take note of the Guest account’s network name and password. You will need to provide this information to your guests.TIPSTo keep your guest network secure, click Change to change the guest password when the guest no longer needs access to the account.You can view the Guest account’s name and password in Cisco Connect’s main screen.4. In the Total guests allowed drop-down box, select the number of simultaneous guest network users you want to allow.5. Click Finish to apply your changes.TIPThe first time your guest tries to access the Internet through a web browser, they will see the Guest access screen. To continue, they must enter the password you provided in the Password field, then click LOGIN.

21Setting Up: BasicsLinksys E-SeriesHow to change your router’s name and passwordFor ALLYou can change the name and password of your router, but if you do so, all wireless devices connected to your router will lose their Internet connection until you reconnect them using the new router name and password.CAUTIONIf you change your router’s name and password using the browser-based utility, you may not be able to manage your router using Cisco Connect. We recommend using the procedure below to change your router’s login information.To change your router’s name and password:1. Run Cisco Connect, then click Change under Router settings.2. Under Personalize, click Change. A Changing router name and password warning appears3. Click Yes if you want to continue.4. Enter the new router name and password, then click Change.TIPAfter you make changes, update your Easy Setup Key to make it easier to reconnect all of the other computers on the network.

22Setting Up: AdvancedLinksys E-Series22How to open the browser-based utilityFor ALLTo access some advanced settings, you need to open the browser-based utility. CAUTIONIf you change settings in the browser-based utility, you might not be able to run Cisco Connect later. To open the browser-based utility:1. Run Cisco Connect, click Change under Router settings, click Advanced settings, then click OK.– or –Open a web browser on a computer connected to your network, then go to 192.168.1.1.The router prompts you for a user name and password.2. Enter the user name and password, then click OK. The utility’s main menu opens.TIPIf you set up your router without using Cisco Connect, your router’s default password is admin. (You can leave the user name blank.)How to manually set up your routerFor ALLAlthough running Cisco Connect is the easiest way to set up and maintain your router, advanced users may want to manually configure their router. Be careful when changing settings using this method.To manually set up your router:1. If you have started the Cisco Connect setup, exit Cisco Connect.2. Connect your router’s power adapter to a power outlet.3. Connect an Ethernet cable to the computer and to an available numbered Ethernet (blue) port on the back of your router.Setting Up: Advanced

23Setting Up: AdvancedLinksys E-Series4. Open a web browser on the computer and open the address 192.168.1.1. A login window appears.5. Enter the default password (admin). (You can leave the user name blank.) The browser-based utility opens to the main menu.6. After you finish changing settings, click Save Settings at the bottom of the screen.7. To exit the browser-based utility, close the web browser window.TIPFor field descriptions, click Help in the right side of the screen.How to manually set up your Internet connectionIn most cases, Cisco Connect automatically sets up your Internet connection (see “How to start Cisco Connect” on page 11). For some ISPs (Internet Service Providers), especially those outside of the United States, you may need to manually configure your router’s Internet connection. Your router supports six types of Internet connections.To manually configure your router’s Internet connection:Setup > Basic Setup1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Setup tab, then click the Basic Setup page.3. In the Internet Connection Type drop-down list, click the type of Internet connection provided by your ISP. TIPFor field descriptions, click Help on the right side of the screen.4. Complete the fields required by your ISP.5. Complete the Optional Settings only if required by your ISP.6. Click Save Settings at the bottom of the page.How to get the most out of your dual-band routerFor E2500 E3200 E4200I bought a dual band router, but I’m not sure that I’m getting the most out of it. What should I check? Of the many reasons for owning a dual-band router, the most common is to ensure available bandwidth for streaming high-definition video. At the same time, owners want to make sure that their video streams won’t be interrupted by other wireless network traffic. To get the most out of your dual-band router, you can: • Upgrade your wireless clients • Split your traffic

24Setting Up: AdvancedLinksys E-SeriesUpgrade your wireless clientsIf you have network adapters that support only legacy wireless network standards such as 802.11b, you should consider upgrading them with Wireless-N (802.11n) network adapters. Wireless-B (802.11b) devices can slow your entire wireless network. For the best performance, all of your wireless devices should support Wireless-N. You can then select Wireless-N Only as your Network Mode below.NOTEIf you select Wireless-N Only, you may need to temporarily change your network settings to Mixed to provide access to guests without Wireless-N networking.Split your trafficThe best way to improve your multimedia wireless performance is to split your wireless traffic between your router’s two bands (ranges of radio frequencies). Your router supports the 2.4 GHz band and the 5 GHz band, and handles the two bands as two separate wireless networks to help manage the traffic.The most common way to split wireless traffic is to use the 2.4 GHz band for basic Internet tasks such as web browsing, email, and downloads, and use the 5.0 GHz band for streaming multimedia. There are several reasons for this approach: • Although the 2.4 GHz band may be more crowded with wireless traffic from your neighbors, it’s fine for basic Internet traffic that is not time-sensitive (such as e-mail). • Even though you are connected to your own wireless network, you are still sharing “air time” with nearby networks. • The 5 GHz band is much less crowded than the 2.4 GHz band, so it’s ideal for streaming multimedia. • The 5 GHz band has more available channels, so it is more likely that you will have your own, interference-free channel for your wireless network.By default, your dual-band router uses the same network name on both the 2.4 GHz band and the 5 GHz band. If you are connecting to your router with a computer that has a dual-band wireless network adapter, you might not be able to determine which band you’re using. The easiest way to segment your traffic is to rename one of your wireless networks. With a separate, descriptive name, it will be easy to connect to the right network.To reconfigure your wireless network:Wireless > Basic Wireless Settings1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Wireless tab, then click the Basic Wireless Settings page.3. Click Manual. This enables you to make changes to all of the fields below. a. Network Mode—Your choice depends upon the clients that will connect to your network. If all of your devices are Wireless-N capable, you can select Wireless-N Only for either or both bands.On the 5 GHz band, you can select: • Mixed (default), which accepts connections from 802.11a or 802.11n clients • Wireless-A Only (802.11a only) • Wireless-N Only (802.11n only) • Disabled, which disables the 5.0 GHz band on this routerOn the 2.4 GHz band, you can select: • Mixed • Wireless-B/G Only • Wireless-B only • Wireless-G Only • Wireless-N Only • Disabled

25Setting Up: AdvancedLinksys E-Seriesb. Network Name (SSID) – Provide a unique SSID for your 5 GHz wireless network. The name must not exceed 32 keyboard characters. In the example above, the 5 GHz wireless network was renamed BronzeEagle5GHz.c. Channel Width – We recommend that you keep the default (Auto) settings. In Auto mode, the router and the network clients automatically switch to the 40 MHz mode if: • Your wireless clients support the 40 MHz mode (sometimes called Bonded mode) in which two 20 MHz channels are bonded together for better performance. • There is no adjacent interference.With more available channels and less chance of interference on the 5 GHz band, you have the option to force the 40MHz mode. On the 5GHz band, you can select: • Auto (20 MHz or 40 Mhz) • 20 MHz Only • 40 MHz OnlyOn the 2.4 GHz band, you can select: • Auto (20 MHz or 40Mhz) • 20 MHz Only d. Channel – Choose the operating channel for each band. Your router will automatically select the channel with the least amount of interference if you leave the default Auto or Auto (DFS) setting. We recommend keeping the default settings for both bands.e. SSID Broadcast – When wireless clients look for wireless networks to connect to, they detect the SSID (wireless network name) broadcast by the router. To broadcast your router’s SSID, keep the default setting (Enabled). If you do not want to broadcast the router’s SSID, select Disabled. We recommend keeping the default setting (Enabled) for both bands.4. To apply your changes, click Save Settings at the bottom of the screen.How to set up the DHCP server on your routerFor ALLYour router can be used as a DHCP (Dynamic Host Configuration Protocol) server to automatically assign an IP address to each computer or device on your network. The DHCP server is enabled by default. If you already have a DHCP server on your network, or if you do not want to use your router as a DHCP server, you should disable this setting. To configure your router’s DHCP server settings:Setup > Basic Setup > DHCP Server Settings1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Setup tab, then click the Basic Setup page.3. Review the DHCP Server Setting fields (in the middle of the screen). You can: • Enable or disable the DHCP server. • Change the starting address for the DHCP server. • Change the number of users (253 maximum). 4. If you change any of the settings, click Save Settings at the bottom of the page.TIPFor field descriptions, click Help on the right side of the screen.

26Setting Up: AdvancedLinksys E-SeriesHow to set up DHCP reservationWhy would I use it? DHCP reservation allows you to assign a unique, fixed IP address to a specific device on your network. Assigning a fixed IP address is a good way to manage devices such as print servers, web cameras, network printers, and game consoles. A fixed IP address is also recommended if you want to use port forwarding for devices that need to receive inbound traffic from the Internet (“How to set up port forwarding” on page 51). To configure DHCP reservation:Setup > Basic Setup > DHCP Reservation1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Setup tab, then click the Basic Setup page.3. Click DHCP Reservation (in the middle of the screen). 4. Click Select next to the client you want to create a DHCP reservation for.5. Click Add Clients. The client you selected is added to the Clients Already Reserved table.You can also manually enter a client name, IP address, and MAC address of a device to create a DHCP reservation.6. Click Save Settings.TIPFor field descriptions, click Help on the right side of the screen.How to find your network on the InternetFor ALLWhy would I need to find my network on the Internet? If you want to remotely access a USB drive attached to your router or view a web camera, you need to find your network on the Internet.Working with several DDNS service providers, your router’s DDNS feature lets you configure a domain name for your network, which you can then use to easily find your network on the Internet. If your ISP changes your network’s IP address, the DDNS service providers detect the address change and continue to route your domain name to that address.TIPBefore you configure DDNS on your router, you must sign up for DDNS service from a DDNS service provider that’s supported by your router.To set up DDNS:Setup > DDNS1. Sign up for DDNS service at either www.dyndns.org or www.tzo.com.2. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 3. Click the Setup tab, then click the DDNS page.4. In the DDNS Service drop-down list, click your DDNS service provider. The examples below are based on TZO.com. The settings used by DynDNS.org are slightly different.

27Setting Up: AdvancedLinksys E-Series5. Complete the fields with information provided by your DDNS provider, then click Save Settings. The Status field tells you what actions have been taken.In this example, the domain name registered with TZO.com is BronzeEagle953.linksysnet.com. If an Internet camera had been configured (see “How to set up port forwarding for a single port” on page 51), you could access the camera by typing the domain name into the address bar of your web browser followed by the port number used for the device. For example, if the camera in the above example used port 1024, the URL would be:BronzeEagle953.linksysnet.com:1024How to clone a MAC addressFor ALLOn any home network, each network device has a unique MAC (Media Access Control) address. Some ISPs register the MAC address of the device (usually a router or a computer) connected directly to the modem. If your computer’s MAC address is registered with your ISP and you do not want to re-register the MAC address, then you can clone the address (assign the registered MAC address of your previous device to your new router). If you want to use the MAC address from an old router that you are replacing with your new router, you should first determine the MAC address of your old router, then manually enter it into your new router.NOTEFor many ISPs that provide dynamic IP addresses automatically, the stored MAC address in the modem is reset each time you reset the modem. If you are installing this router for the first time, reset your modem before connecting the router to your modem. To reset your modem, disconnect power for about one minute, then reconnect power.To clone a MAC address from your computer:Setup > MAC Address Clone1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Setup tab, then click the MAC Address Clone page.3. Click Enabled.4. Click either Clone My PC’s MAC or enter the 12-digit MAC address of your old router.5. Click Save Settings.

28Setting Up: AdvancedLinksys E-SeriesHow to connect to your corporate office using a VPNFor ALLWhat is a VPN, and do I need to change my router settings? A VPN (Virtual Private Network) is a network that uses a public network, such as the Internet, to provide secure communications between a remote computer and another network. Corporations often provide VPN access to their networks to enable employees to work from remote offices or while traveling. Most corporate VPNs use the Internet to provide connectivity between remote employees and the corporate network. For a typical VPN, the corporation installs a VPN gateway on their corporate network. Employees authorized to work remotely connect to the VPN gateway through the Internet using VPN software and security methods provided by their employers. Robust security and authentication schemes ensure a secure connection and access by only authorized users.The default VPN settings in your router have been configured to pass through (allow) the most common types of VPN protocols, so usually no changes are needed. To change your VPN passthrough settings:Security > VPN Passthrough1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Security tab, then click the VPN Passthrough page.3. Select each setting that you want to change.TIPFor brief descriptions of the VPN passthrough field settings, click Help in the right side of the screen. More complete descriptions are provided below. • IPSec Passthrough – IPSec (Internet Protocol Security) is a suite of protocols used to implement secure exchange of packets at the IP layer. The VPN clients on the local network can establish an IPSec VPN tunnel through the router. This option is enabled by default. • PPTP Passthrough – PPTP (Point-to-Point Tunneling Protocol) allows the PPP (Point-to-Point Protocol) to be tunneled through an IP network. The VPN clients on the local network can establish a PPTP VPN tunnel through the router. This option is enabled by default. • L2TP Passthrough – L2TP (Layer 2 Tunneling Protocol) enables point-to-point sessions using the Internet on the Layer 2 level. The VPN clients on the local network can establish an L2TP VPN tunnel through the router. This option is enabled by default.4. Click Save Settings to save your changes.How to optimize your router for gaming and voiceFor ALLHow does my router prioritize traffic to the Internet? Your router has QoS (Quality of Service) settings that can prioritize traffic from your network out to the Internet. Performance for demanding, real-time applications, such as online gaming, VoIP calls, video streaming, and videoconferencing, can be improved by configuring Internet access priorities.QoS is applied only to traffic that is uploaded to the Internet. The router cannot control the quality of the traffic after it reaches the Internet.TIPFor more information on optimizing your router for online gaming, see “Port Forwarding and Port Triggering” on page 51.

29Setting Up: AdvancedLinksys E-SeriesTo configure QOS:Applications & Gaming > QoS1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Applications & Gaming tab, then click the QoS page.TIPFor field descriptions, click Help on the right side of the screen.3. To help manage traffic priority with devices that support WMM, select Enabled under WMM Support. Otherwise, select Disabled.TIPWMM (Wi-Fi MultiMedia) Support is a wireless QoS feature based on the IEEE 802.11e standard. WMM improves quality for audio, video, and voice applications by prioritizing wireless traffic. This feature requires that the wireless client devices in your network also support WMM.4. To have the router re-send data if an error occurs, select Disabled under No Acknowledgement. Otherwise, select Enabled.5. To set access priorities for a specific device or application, select Enabled next to Internet Access Priority. 6. In the Category drop-down list, select the type of item you want to set a priority for. A list of installed items fitting that description appears.TIPDo not set all priorities to High, because all items will have the same priority, and it would be easier to disable Internet Access Priority for the same result. • Applications and Online Games—Let you assign a priority for an application or online game.a) Select the application or online game that you want to add from the drop-down list, then select the priority.b) Click Apply, then click Save Settings. TIPIf you want to add a new application or game, you need to know its port and protocol information (see the application or game’s documentation for help). • MAC Address and Voice Device—Let you prioritize network traffic based on the device that is accessing the network. For example, if you want your gaming console to have higher priority than your computer for accessing the Internet, you can assign a higher priority to your game console using its MAC address. We recommend giving any voice devices a high priority.a) Select MAC Address or Voice Device from the drop-down list, then enter the name of the device you want to add.b) Enter the device’s 12-digit MAC address, then select the priority.c) Click Apply, then click Save Settings. TIPYou can often find a device’s 12-digit MAC address on the bottom of the device. Or, if the device is connected to your network and turned on, you can click the Administration tab in the router’s browser-based utility, click the Local Network page, then click DHCP Client Table.

30Setting Up: AdvancedLinksys E-Series7. Configure Upstream Bandwidth. • To allow the router to detect the maximum, select Auto (default). Auto sets speeds in multiples of 512 Kbps. • To specify the maximum, select Manual, then select the bandwidth you want it to use.CAUTIONIf you specify a maximum bandwidth that is too high, the router cannot apply priorities correctly, and QoS problems may result.8. When you are done setting priorities, click Save Settings.How to remotely change your router settingsFor ALLWhy would I want to remotely change my router settings? There may be times when you want to change parental control settings, or change settings for remote file access, while you are away from home. To set up remote access:Administration > Management1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Administration tab, then click the Management page and locate the Remote Management Access settings in the middle of the screen. 3. For Remote Management, select Enabled.4. For Access via, select HTTP (default) or select HTTPS to use SSL (Secure Socket Layer) to encrypt data transmitted for higher security.5. To be able to upgrade your router’s firmware remotely, select Enabled next to Remote Upgrade.6. To allow remote access from anywhere on the Internet, select Any IP Address (default) next to Allowed Remote IP Address. Otherwise, enter a range of allowed IP addresses.7. For Remote Management Port, keep the setting of 8080 (default) unless you already have a device on your network that uses port 8080 (such as a web camera).8. Click Save Settings at the bottom of the screen to accept your changes.9. Click the Administration tab, then click the Management page and take note of the Internet IP Address and the Remote Management Port settings. You will use this information to access your router remotely.To access your router remotely:1. Open a web browser and enter the Internet address of your router, then press Enter. • If you selected HTTP for your Access via setting, enter http:// then the IP address.– OR – • If you selected HTTPS for your Access via setting above, enter https:// then the IP address.2. Add a colon (:), then the Remote Management Port number. Example:https://69.192.16.170:8080TIPIf you enabled the Dynamic Domain Name Service (see “How to find your network on the Internet” on page 26), you could type in your domain name in place of your router’s Internet IP address. For example: https://BronzeEagle953.linksysnet.com:8080You are prompted for a user name and the password. Use the same login information that you use to access your router at home.

31Setting Up: AdvancedLinksys E-SeriesAfter you have logged into your router’s browser-based utility remotely, you can change any router setting, just as you would normally from your local network. How to enable Voice over IP on your networkFor ALLDo I need to configure Voice over IP? VoIP (Voice over Internet Protocol) is a technology for using the Internet as an interface for telephone communications. To use VoIP, you need to get an account with a VoIP service provider. The VoIP service provider typically provides you with a telephone adapter (TA) that connects to your network. If you do not use your network to make phone calls, you don’t need to change the default settings.The SIP (Session Initiation Protocol) ALG (Application Layer Gateway) feature allows SIP packets, used by some VOIP service providers, to traverse (go through) your router’s firewall. To configure the router for VoIP:Administration > Management1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Administration tab, then click the Management page.3. If your VoIP service uses SIP, select Enabled next to SIP ALG.– OR –If your VoIP service uses other NAT traversal solutions such as STUN (Session Traversal Utilities for NAT), TURN (Traversal Using Relay NAT), or ICE (Interactive Connectivity Establishment), select Disabled (default).NOTEYou may need to contact your VoIP service provider to determine the type of NAT traversal configuration they use.How to configure UPnPFor ALLWhat is UPnP? UPnP (Universal Plug and Play) allows devices connected to a network to discover each other and automatically create working configurations. Examples of UPnP-capable devices include web cameras, online gaming applications, and VoIP devices. UPnP is enabled by default.To configure UPnP:Administration > Management1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Administration tab, then click the Management page.3. To use UPnP, select Enabled (default) next to UPnP. Otherwise, select Disabled.4. To allow changing router settings while using UPnP, select Enabled (default) next to Allow Users to Configure. Otherwise, select Disabled.5. To prevent local network users from disabling your Internet connection through UPnP, select Disabled (default) next to Allow Users to Disable Internet Access. Otherwise, select Enabled.How to use a router as an access pointHow can I use my old router as an access point? If you have a large area to cover with your wireless signal, or if part of your home has weak signals due to interference, you can use your old router to extend the range of your wireless network. This is a complex process, so this procedure assumes that you have some networking knowledge.TIPCheck the documentation for your old router. Some brands of routers include either a switch on the outside of the case or a software option to convert it to an access point. If either of these options is available, follow your old router’s instructions to convert it to an access point.

32Setting Up: AdvancedLinksys E-SeriesYou need to take note of your new router’s settings, then apply some of those settings to the old router so it can work as an access point.To view your new router’s settings:Wireless > Basic Wireless Settings Wireless > Wireless Security Status > Wireless Network Setup > Basic Setup1. Make sure that your new router is connected to the Internet. 2. In the browser-based utility, click the Wireless tab, then click the Basic Wireless Settings page and take note of the Network Name (SSID).3. Click the Wireless tab, then click the Wireless Security page and take note of the Security Mode and the passphrase.4. Click the Status tab, then click the Wireless Network page and take note of the Channel.5. Click the Setup tab, then click the Basic Setup page and take note of the DHCP server’s IP Address range (192.168.1.100 to 192.168.1.149 by default)To use your old router as an access point:1. With your computer connected to your old router, log into its browser-based administration utility. NOTESave your changes after finishing each step below.2. Open the setup page for the local network (LAN).3. In the Router IP address field, enter an unused IP address for the LAN network of your new router. For example, if your new router has an IP address of 192.168.1.1, you should choose an IP address on the 192.168.1.0 network. You can choose any address within the range of 192.168.1.2 to 192.168.1.254. You should exclude addresses in the range that will be used by the DHCP Server of your new router (192.168.1.100 to 192.168.1.149). A safe choice might be 192.168.1.250. Take note of this address, because this will be the address that you will use to manage your old router in the future.4. In the Subnet Mask field, enter 255.255.255.0 or, if available, select that subnet mask from a drop-down list.5. Disable the DHCP server on your old router. (Because your old router will be operating as an access point instead of a router, you don’t want it to distribute IP addresses. There should be only one active DHCP server on your network, and that should be your new router.)6. To reconfigure the wireless network on your old router:a. Open the wireless network setup page. b. Change the network name (SSID) to match the name of your new network. Having the same network name and security settings enables you to seamlessly roam between your new router and your old router.c. Change the security mode to match the security mode on your new router. d. Change the passphrase (sometimes called the pre-shared key) on your old router to match the passphrase on your new router.e. Change the wireless channel to a non-conflicting channel. Some manufacturers have an “Auto” function for channel selection that automatically selects a wireless channel that does not interfere with other nearby wireless networks. If your old router supports an Auto function, select that. Otherwise, you may need to manually select the wireless operating channel on your old router. In the 2.4 GHz wireless spectrum, there are only three non-overlapping channels: 1, 6, and 11. Pick a channel that does not overlap the operating channel of your new router. For example, if your new router is operating on channel 11, configure your old router for either channel 1 or channel 6.7. Connect an Ethernet network cable to one of the LAN/Ethernet ports on your old router and an Ethernet port on your new router.CAUTIONDo not connect the cable to the Internet port on your old router. If you do, you may not be able to set up the router as an access point on the current network.

33Setting Up: AdvancedLinksys E-SeriesHow to put your new router behind an existing routerFor ALLWhy would I put my new router behind an existing router? There are several possible scenarios in which you might want to use your new router “behind” another router:1. You might be in an environment that shares the landlord’s Internet connection with all tenants. In this case, you should put your own router behind the landlord’s router in order to create your own private network and to isolate computers on your network from the rest of the building.2. You are sharing an office building Internet connection, and you want to control Internet access or the content viewed by your employees.3. You already have an existing network and you want to extend the network’s range or add wireless capabilities to your network.4. You want to separate older, less secure network devices from the rest of the network.To add your router to an existing router or gatewayIn most cases, you can easily add your router to an existing wireless network by running Cisco Connect. If you are unable to set up the additional router using the instructions below, see “To share an Internet connection” on page 33 or “To extend your network” on page 35.To add a router to your existing wireless network:1. Insert the Cisco Connect setup CD into a CD/DVD drive on your computer, then follow the on-screen instructions.2. When you are told to connect your router’s Internet port to the LAN/Ethernet port on your modem, connect your router’s Internet port to the LAN/Ethernet port on your existing (upstream) router or gateway.3. Follow the on-screen instructions until setup is complete.To share an Internet connectionNOTEThis is a complex process, so this procedure assumes that you have some networking knowledge.To add another router to share an Internet connection:This topic covers cases one and two above1. Determine the IP address range for your upstream (office or building) network. To determine the address range by using a Windows computer:a. Connect your computer into your upstream network’s router.b. Click Start, Run, type CMD, then click OK. The command prompt window appears.c. Type ipconfig, then press Enter. TIPAlthough you can determine your computer’s IP address in many ways, this method is very fast.d. Take note of the IP address. In this example, the IP address is 192.168.100.192.

34Setting Up: AdvancedLinksys E-SeriesTo determine the address range by using a Mac computer:a. Connect your computer into your upstream network’s router.b. From the Dock, click System preferences, click Network, then click Ethernet in the window to the left. A network status window appears.c. Take note of the IP address. In this example, the IP address is 192.168.100.139.Example: The above examples show that upstream IP addresses are on the 192.168.100.0 network. (The “0” indicates the entire network.) Your upstream network’s address may be different. The default address of your new Linksys router is 192.168.1.1. In setting up one router behind another, you must make sure that the local network on your new router is different than the network of your upstream router. In the above example, because the default local network on your Linksys router 192.168.1.0 is on a different subnet than the office network’s 192.168.100.0, you will be able to place your Linksys router behind the other router.2. Connect an Ethernet network cable to a LAN/Ethernet port on your upstream network to the yellow Internet port on your router. CAUTIONConnect the upstream network to your router’s yellow Internet port, not one of the blue Ethernet ports. If you connect to an Ethernet port, you create IP addressing problems for the office network.TIPSAn office network often has a wall plate with an Ethernet port that you can connect to. If you are doing this in a home environment (without wall ports), connect an Ethernet network cable between a LAN port on your upstream router and the Internet port on your Linksys router.3. Run Cisco Connect on each computer that you want to connect to the Linksys router. Each computer needs either a wired or wireless connection to the Linksys router. For more information, see “How to connect a computer to your network” on page 13.The computers that are connected to the Linksys router are now on the same network, and are isolated from the upstream network. However, you will still have access to the Internet through the upstream router (by way of your Linksys router). Because two routers are between your computer and the Internet, Internet traffic undergoes two network address translations. This is sometimes referred to as Double NAT.Your computers can also use the built-in capabilities of your Linksys router, such as parental controls. If you need further control over the type of content your employees or family access, you can create an account with an Internet filtering site such as www.opendns.com or www.bsecure.com. After you create an account with them, use their DNS in place of your ISP’s DNS. To use their DNS:Setup > Basic Setup1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Setup tab, then click the Basic Setup page.

35Setting Up: AdvancedLinksys E-Series3. Complete the Static DNS fields with the information provided by your content filtering provider.4. Click Save Settings.To extend your networkThis topic covers cases three and four above.NOTEThis is a complex process, so this procedure assumes that you have some networking knowledge.To extend your network or add wireless capabilities: 1. If you want to extend your network, you may also follow the instructions above. One example of this might be to provide a separate wireless network for your children to keep their wireless network traffic separate from your wireless network. You might also want to isolate one network from another network so that network shares aren’t visible across networks. In this case, use an Ethernet cable to connect the Internet port of the downstream router to one of the LAN ports of the upstream router. Make sure that the local network subnets on the two routers are different.- OR -You can extend your network by turning the downstream router into an access point. (See “How to use a router as an access point” on page 31). When you use a router as an access point, computers connected to the access point are on the same IP subnet as all other devices connected to the router. File, printer, and media sharing is much easier if all devices are on the same subnet.How to expose a device to the InternetFor ALLWhy would I expose a device to the Internet? If you are operating a web server, a mail server, or a web camera, you may want to expose that device to the Internet so anybody can access it. Your router includes a DMZ (Demilitarized Zone) feature that forwards all inbound ports presented on the WAN interface, except those that are specifically forwarded, to an individual IP address or MAC address. This feature is normally not used, because it presents significant security risks to the device that you designate for the DMZ. The DMZ device is not protected by the built-in firewalls, Internet filters, or router web filters, and is open to attacks from hackers. A much better way of “exposing” devices to the Internet would be to use port forwarding. See “How to set up port forwarding” on page 51.To set up a device in the DMZ:Applications & Gaming > DMZ1. Configure your device with a static IP address. See your device’s documentation for help with setting a static IP address or use DHCP reservation (see “How to set up the DHCP server on your router” on page 25).2. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 3. Click the Applications & Gaming tab, then click the DMZ page.4. Select Enabled.5. In the Source IP Address section, select Any IP Address to allow access to your DMZ device from the entire Internet, or select the source range button and enter a range of allowed source addresses. 6. In the Destination section, enter the last three digits of the IP address of the device that will be in the DMZ. The rest of the IP address is already completed.

36Setting Up: AdvancedLinksys E-Series7. Click Save Settings to apply your changes.If you prefer to specify the 12-digit MAC address of the device you want to place in the DMZ instead of setting up a DHCP address reservation, you can replace Step 6 with the following steps: a. Click Enabled.b. In the Source IP Address section, select Any IP Address (default) to allow access to your DMZ device from the entire Internet, or select the source range button and enter a range of allowed source addresses. c. In the Destination section, select MAC Address, then click DHCP Client Table. A separate window opens showing the current DHCP client list. d. Click Select next to the device that you want to place in the DMZ. In this example, the first device was selected. The corresponding MAC address was copied into the MAC Address field as shown below. e. Click Save Settings to apply your changes.TIPThe DHCP Client Table is only available if you select MAC Address.

37Improving SecurityLinksys E-Series37How do I know if my network is secure?For ALLIf you configured your router using Cisco Connect, your network is secure. During setup, Cisco Connect creates a name for your network, enables industry-standard WPA/WPA2 wireless security, and assigns a highly secure password for your wireless network and the administrator’s account.To confirm that your network is secure:1. Run Cisco Connect.2. In the upper-right corner of the screen, check for the green light that indicates your router is online and secure. If the green light is on, no additional action is required to secure your network.Network security following a manual setupFor ALLIf you configured your router manually (not recommended), you must manually configure security.To manually set your router’s password:Administration > Management1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Administration tab, then click the Management page.3. In the Router Access section, enter a secure password for your router, then re-enter the password to confirm it. Your password should be at least eight characters in length. The most secure type of password should include a mix of uppercase and lowercase letters, numbers, and punctuation.4. Click Save Settings at the bottom of the screen.To manually set your router’s network name (SSID):Wireless > Basic Wireless Settings1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Wireless tab, then click the Basic Wireless Settings page.3. For Configuration View, select Manual. 4. Enter a new network name in the Network Name (SSID) field, then click Save Settings at the bottom of the screen. Improving Security

38Improving SecurityLinksys E-SeriesTo manually set your router’s wireless security settings:Wireless > Wireless Security1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Wireless tab, then click the Wireless Security page.3. Select your preferred security type from the Security Mode drop-down list For most home networks, we recommend WPA2/WPA Mixed Mode.4. Enter a passphrase (security key) for your wireless network in the Passphrase field. The most secure type of security key should include a mix of uppercase and lowercase letters, numbers, and punctuation.5. Click Save Settings at the bottom of the screen.How to set up wireless security using Wi-Fi Protected SetupFor ALLWhy would I use Wi-Fi Protected Setup? Wi-Fi Protected Setup™ is a feature of your router that makes it easy to add devices to your wireless network. If you have network devices, such as wireless printers, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup to add the devices. Wi-Fi Protected Setup activity lightThe power indicator light on the back of the router (or on top for the E4200) indicates the status of Wi-Fi Protected Setup while you are connecting devices. • When Wi-Fi Protected Setup is connecting a network device, the light flashes slowly. • If there is an error, the light flashes quickly for two minutes. Wait until it stops flashing, then try again. • When Wi-Fi Protected Setup has finished connecting a device, the light is continuously lit . • Wait until the light is continuously lit before starting the next Wi-Fi Protected Setup session.Connect network devices using one of the three methods below.NOTEWi-Fi Protected Setup configures one device at a time. Repeat the instructions for each device that supports Wi-Fi Protected Setup.Connecting a device using the Wi-Fi Protected Setup buttonUse this method if your device has a Wi-Fi Protected Setup button or prompts you to press the Wi-Fi Protected Setup button on your router.To connect a device using the Wi-Fi Protected Setup button:Wireless > Basic Wireless Settings1. Press the Wi-Fi Protected Setup button on the network device you are connecting to.2. Press the Wi-Fi Protected Setup button on the back of the router.- OR -a. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). b. Click the Wireless tab, then click the Basic Wireless Settings page.c. Click Wi-Fi Protected Setup.d. Click the Wi-Fi Protected Setup button in the router’s Wi-Fi Protected Setup screen.e. After the device has been configured, click OK.

39Improving SecurityLinksys E-SeriesHow to connect a device using its Wi-Fi Protected Setup PINUse this method if your device has a Wi-Fi Protected Setup PIN (Personal Identification Number).To connect a device using the device’s Wi-Fi Protected Setup PIN:Wireless > Basic Wireless Settings1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Wireless tab, then click the Basic Wireless Settings page.3. Click Wi-Fi Protected Setup.4. Enter the PIN from the device into the PIN field on the router’s Wi-Fi Protected Setup screen, then click Register.5. After the device has been connected, click OK.How to connect a device using the router’s Wi-Fi Protected Setup PINUse this method if your client device asks for the router’s PIN.To connect a device using the device’s Wi-Fi Protected Setup PIN:Wireless > Basic Wireless Settings1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Wireless tab, then click the Basic Wireless Settings page.3. Click Wi-Fi Protected Setup.4. On the client device, enter the PIN listed on the router’s Wi-Fi Protected Setup screen. It is also listed on the bottom of the router. In the example below, the router’s PIN is 32744781.5. Follow the device’s instructions to complete setup.How to connect a device manuallyIf you have devices that do not support Wi-Fi Protected Setup, note the wireless settings in the Basic Wireless Settings screen, then manually configure those devices.For each wireless network, the Network Name (SSID), Security, and Passphrase are displayed at the bottom of the screen.

40Improving SecurityLinksys E-SeriesHow to control access to your wireless networkFor ALLWhy would I need to control access to my wireless network? If you used Cisco Connect to configure your router, your wireless network is already secure. By default, Cisco Connect enables industry-standard WPA (Wi-Fi Protected Access) security using WPA2/WPA mixed mode. Cisco Connect configures your network with a complex, 10-character password that is almost impossible to compromise. If you set up your wireless network manually and have not enabled wireless security, your wireless network will be an “open” network that almost anyone nearby with a Wi-Fi-enabled device could access. What is MAC filtering? The best way to secure your wireless network is to use Cisco Connect to automatically configure and secure it. However, if you choose not to use the built-in security features of your router, you can still control access to your wireless network using MAC filtering. Every network device has a unique, 12-digit MAC (Media Access Control) address. Using MAC filtering, you can allow only known MAC addresses onto your network. You can also exclude specific MAC addresses or deny them access to your wireless network.Example: Because each MAC filtering configuration is unique, the following procedure uses the simplified example of setting up MAC filtering to allow one wireless device access to the network.To set up MAC filtering to allow one wireless device access to your network:Wireless > Wireless MAC Filter1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Wireless tab, then click the Wireless MAC Filter page.3. Click Enabled.4. Select Permit.TIPYou can also use MAC filtering to prevent specific PCs from accessing your network by selecting Prevent. However, it’s easier to permit only known devices than to exclude unknown devices.5. Click Wireless Client List. A separate window opens and displays the currently connected devices. In the example below, the only device permitted onto the network is the MacBook. However, two other devices are also connected to the network.6. Next to the device entry, select Save to MAC Address Filter List, then click Add. The Mac Address Filter List is updated with the MAC address of the device you added.

41Improving SecurityLinksys E-Series7. Click Save Settings at the bottom of the page.8. Click Wireless Client List again to check the updated device list. Only the device you selected remains on the network.How to improve security using the built-in firewallWhy would I need to change my security settings? By default, the firewall settings in your router have been optimized for most home environments, so no changes are needed. The SPI (Stateful Packet Inspection) firewall is enabled by default. In addition, anonymous Internet requests and IDENT requests are filtered by default. All web filters are disabled, because enabling them may cause problems for sites that depend on ActiveX controls, Java, or cookies.To change your firewall settings:Security->Firewall1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Security tab, then click the Firewall page.3. Select each setting that you want to change. TIPFor descriptions of the filters, click Help on the right side of the screen. More complete descriptions are included below. • SPI Firewall Protection—This helps protect your local network from Internet threats. This option is enabled by default. CAUTIONTo help protect your network, you should keep this option enabled. • Filter Anonymous Internet Requests—This filter blocks Internet requests from unknown sources such as ping requests. This option is enabled by default. • Filter Multicast—Multicasting allows a single transmission to simultaneously reach specific recipients within your local network. Select this option to block multicasting. This option is disabled by default. • Filter Internet NAT Redirection—This filter prevents a local computer from using a URL or Internet IP address to access the local server. Select this option to enable the filter. This option is disabled by default. • Filter IDENT (Port 113)—This filter prevents port 113 from being scanned by devices from the Internet. This option is enabled by default. • Proxy - This filter blocks the use of Internet proxy servers. To deny proxy requests, select this option. Proxy access is allowed by default. • Java - This filter blocks Java, so you may not be able to access Java content on websites. To deny Java requests, select this option. Java content is allowed by default. • ActiveX - This filter blocks ActiveX, so you may not be able to access ActiveX content on websites. To deny ActiveX requests, select this option. ActiveX content is allowed by default. • Cookies - This filter blocks cookies, which are data stored on your computer and used by websites when you interact with them. To deny cookie requests, select this option. Cookie usage is allowed by default.4. Click Save Settings to update your changes.

42Using an External DriveLinksys E-Series42How to configure storageFor E3200 E4200Why would I need to configure storage? By default, when you connect a storage device to your router, the entire contents of the device are available for read and write access to anyone on your local network (no login credentials are required). However, you can also create shared folders that you can configure to share only with specified groups.To control access to the USB drive attached to your router, you need to perform two tasks:1. Create one or more shared folders (see “How to create shared folders” below)2. Manage group and User Access to Shared Folders (see “How to share folders and set access rights” on page 47)How to create shared foldersTo create a shared folder:Storage > Disk1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Storage tab, then click the Disk page.3. Click Create Share next to the partition you want to share. The Shared Folder screen opens.4. If you want to share the entire partition, select Share Entire Partition, then click Save Settings at the bottom of the screen.- OR –If you want to share a specific folder:a. Enter a unique name in the Display Name field.b. Click Select next to the folder name you want to share. • To open a subfolder, click Enter into Folder. • To navigate to a previous folder, click Return to Upper Folder. • To create a new folder, type the name into the New Folder field, then click Create. Using an External Drive

43Using an External DriveLinksys E-Seriesc. Click Save Settings at the bottom of the screen, then repeat the above steps to add more folders that you want to share. How to manage group and user access to shared foldersTo manage access to shared folders, you need to disable Anonymous Disk Access, then create groups and user accounts on your router. Access to the router is controlled by user accounts, but access to shared folders is controlled by groups. 1. Disable Anonymous Disk Access (see “How to disable anonymous disk access” on page 43).2. Create a group that you will use to assign rights to a shared folder.3. Create users and assign those users to the group.4. Add the group to the shared folder that you want to control.How to disable anonymous disk accessBy default, no password is needed for read and write access to the drive. Before you can manage group and user access to shared folders, you must disable anonymous disk access.To disable anonymous disk access:Storage > Administration1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Storage tab, then click the Administration page.3. Next to Anonymous Disk Access, select Disabled.4. Click Save Settings at the bottom of the screen.How to create a groupBy default, the default Admin group has read and write access to all shared folders. By default, the Guest group has read only access and has no access rights to any of the shared folders.IMPORTANTMore than one group can be configured with access to a shared folder, but a user can be a member of only one group.To create a group:Storage > Administration1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Storage tab, then click the Administration page.

44Using an External DriveLinksys E-Series3. Under Group Management, click Create New Group.4. Complete the Group Name and Description fields.5. From the Access drop-down list, select read-only to grant read-only rights to the group, or select read-and-write to grant read and write rights to the group.6. Click Create. The group is now created, and its access rights are displayed in the Access column.7. To change a group’s name or access rights, click Edit next to the group name.8. To delete a group, click Delete next to the group name.How to create a new userTwo user accounts (Admin and Guest) are preconfigured for router access. The password for the Admin user is the same password that you use to access the router. By default, the user Admin is a member of the group named Admin, and the user Guest is a member of the group named Guest. To keep it simple, consider creating user accounts on your router that use the same user names and passwords that are used by your computer’s operating system. NOTEUsers can be a member of only one group.To create a new user:Storage > Administration1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Storage tab, then click the Administration page.3. Under User Management, click Create New User.4. Complete the Name, Full Name, and Description fields. 5. Enter and confirm a password.

45Using an External DriveLinksys E-Series6. From the Group Member drop-down list, select the group to assign the user to, then click Create. The new user is displayed in the user list.7. To change the user name, description, or group membership, or to temporarily disable the account, click Edit.8. To delete the user, click Delete.How to grant group access to a shareTo grant group access to a shareStorage > Disk1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Make sure that Anonymous Disk Access has been disabled. (See “How to disable anonymous disk access” on page 43.)3. Click the Storage tab, then click the Disk page.4. In the Shared Folder section, click Edit next to the shared folder you want to change group access for.5. To grant a group access the shared folder, click the group’s name in the Available Groups column, then click >> to move the group to the Groups with Access column.6. To remove a group’s access to the shared folder, click the group’s name in the Groups with Access column, then click << to move the group to the Available Groups column.7. Click Save Settings to apply your changes.

46Using an External DriveLinksys E-SeriesHow to configure your router’s storage for remote accessFor E3200 E4200Why would I need to access my router’s storage remotely? If your router’s storage is set up for remote access, you can access your files anywhere you have an Internet connection. To do this, you must enable the router’s built-in FTP (File Transfer Protocol) server. After your router is set up, you can access files from anywhere by using either a web browser or FTP software.To set up your router for remote file access, you need to:1. Configure the FTP server2. Select folders (or the entire drive) to share and set access rights for those foldersHow to configure the FTP serverTo configure the FTP server:Storage > FTP Server1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Storage tab, then click the FTP Server page.3. Next to FTP Server, click Enabled.TIP If you used Cisco Connect to set up your router, the FTP Server Name field is already completed with the name of your wireless network. If you set up your router manually, the default name is Cisco followed by the last five digits of the router’s serial number.4. You can also: • Change the FTP Port (default is 21) for the FTP server • Change the Encoding (character set) for the transfer of files in other languages. The router supports: • Unicode (UTF-8) (default) • Chinese Simplified (GB18030) • Vietnamese (CP1258) • ISO 8859_1. TIPFor field descriptions, click Help on the right side of the screen.5. To apply your changes, click Save Settings.

47Using an External DriveLinksys E-SeriesHow to share folders and set access rightsYou can select which folders to share. You can also select which users can access the folders. For more information on managing access rights, see “How to configure storage” on page 42. To configure FTP and control folder access:Storage > FTP Server1. In the Storage tab’s FTP Server page, click Specify Folder.The FTP Folder screen opens in a separate window.2. In the Display Name field, enter a unique name for the FTP folder. The name must use only alphanumeric characters (letters A to Z and numbers 0 to 9) and can be up to 15 characters long.3. To share the entire drive, click Share Entire Partition. – OR -To share only specific folders: • Click Select next to the folder you want to share. • To navigate to a previous folder, click Return to Upper Folder. • To view and select folders within a folder, click Enter into Folder next to the folder name.4. To create a folder, enter a unique folder name into the New Folder box, then click Create.5. To change group access, select a group in the Available Groups or Groups with Access column, then click >> or << to move the group to the other column.6. To apply your changes and enable FTP access, click Save Settings.7. To apply your changes and create the shared folder for FTP access, click Save Settings. You are returned to the FTP Server page, where a summary of shared folders is displayed.8. To modify shared folder settings: • To change a FTP folder’s name or group access, click Edit. • To delete an FTP folder, click Delete. • To see a detailed summary of FTP folders, click Summary. A separate window opens and shows the folder’s Display Name, Partition, Share Folder, and Groups with Access. Click Close to close the window.

48Using an External DriveLinksys E-SeriesHow to access files remotelyFor E3200 E4200To access files remotely, you must first attach a USB drive to your router and set up that storage for remote access. For instructions, see “How to configure your router’s storage for remote access” on page 46. You can then access files from anywhere on the Internet.To access files remotely:1. Make sure that your router is configured to share files. For more information, see “How to configure your router’s storage for remote access” on page 46.2. Make sure that your router has user accounts set up, and that you have taken note of the user name and password you will use to access the router’s storage. If you have enabled Anonymous FTP (not recommended), you will not need a user name and password. For more information, see “How to configure storage” on page 42.3. Take note of the IP address of your router. To view your router’s IP address, open the browser-based utility, click the Status tab, then click the Router page and take note of the numbers in the Internet IP Address field.– OR –If you have DDNS (Dynamic Domain Name Service), take note of the domain name registered to your router. For more information, see “How to find your network on the Internet” on page 26.4. At any remote location where you can access the Internet, you can: • Use FTP (File Transfer Protocol) client software to connect to your router. You will need to enter your router’s IP address. If access to your router requires a user name and password, you will also need to enter those details. For more information on using the FTP client software, see its documentation or help.– OR – • Type the router’s IP address into a web browser’s Internet address field, press Enter, then enter your user name and password.FTP software and web browsers display FTP content in many ways, but you can usually use these common actions to navigate through FTP folders: • Click a folder name to open it. • Click a double period (..) or Up to a higher level directory to open a parent folder. • Click or right-click a file to download or view it. • Drag a file from another window and drop it into the FTP window to upload it. (To upload a file, your user account must have write access.)How to set up your router as a media serverFor E4200What is a media server and how would I use it? A media server lets you share media content across your network. Your router can act as a media server if it has a USB drive attached if you have UPnP AV (Audio and Video)-enabled or DLNA (Digital Living Network Alliance)-certified devices in your home. Examples of UPnP AV-enabled devices include digital media players, gaming consoles with a built-in media player, and digital picture frames.For example, if you have a digital media adapter that sends content to your entertainment system, and if your router’s set up as a media server, then the digital media adapter can access your router’s attached USB drive.You can specify which folders are used by the media server, add and delete folders, and specify how often the folders are scanned for new content. To configure your router as a media server:Storage > Media Server1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Storage tab, then click the Media Server page.3. Click Enabled to enable the media server.

49Using an External DriveLinksys E-Series4. Enter a name for your media server in the Media Server Name box. The name must use only alphanumeric characters (letters A to Z and numbers 0 to 9) and can be up to 15 characters long.5. Click Specify Folder to Scan. A new window opens.6. In the Display Name field, enter a unique name for the media folder. The name must use only alphanumeric characters (letters A to Z and numbers 0 to 9) and can be up to 15 characters long.7. To share the entire drive, click Share Entire Partition. – OR -To share only specific folders: • Click Select next to each folder you want to share. • To navigate to a previous folder, click Return to Upper Folder. • To view and select folders within a folder, click Enter into Folder next to the folder name.8. To create a folder, enter a unique folder name into the New Folder box, then click Create.9. To save your selections and create the media folder, click Save Settings. A summary of shared folders is displayed10. To delete an individual media folder, click Delete. NOTEIf you delete a media folder, you are not deleting the folder’s contents. You are only removing it as a folder that the media server will use.11. To manually scan all shared folders, click Scan All.– OR -To scan an individual folder, click Scan next to the folder.12. To schedule a scan of the media folder for new media content, select Auto-scan every, then select a time interval from the drop-down list.

50Using an External DriveLinksys E-SeriesHow to connect your UPnP device to the media serverAfter you set up your router’s media server, you need to connect an UPnP-compatible device (such as an UPnP-compatible game console or digital media player) to the network so that you can play the media server’s content.To connect an UPnP device to your router’s media server:1. Connect your UPnP device to your home network with wired (Ethernet cable) or wireless networking. If you are connecting wirelessly, you need to know your network’s name and password. See your device’s documentation for help. 2. On your UPnP device, change the media source to the media server name you specified on your router. (See “How to set up your router as a media server” on page 48)3. See your UPnP device’s documentation for help with playing media on the device.

51Port Forwarding and Port TriggeringLinksys E-Series51How to set up port forwardingFor ALLWhy would I use port forwarding? Port forwarding is a feature that forwards inbound traffic from the Internet on a specific port or ports to a specific device or port on your local network. You can set up port forwarding for: • A single port (see “How to set up port forwarding for a single port” below) • Multiple ports (see “How to set up port forwarding for multiple ports” on page 52) • A range of ports (see “How to set up port forwarding for a range of ports” on page 52)How to set up port forwarding for a single portWhy would I use port forwarding for a single port? Single port forwarding is a feature that forwards inbound traffic from the Internet on a specific port to a single device on your local network. An example of single port forwarding would be to forward inbound web requests, typically on port 80, to a web server. To set up single port forwarding:Applications & Gaming > Single Port Forwarding1. Follow your device’s instructions for configuring it with a static IP address or use DHCP reservation to assign it a permanent address (see “How to set up the DHCP server on your router” on page 25).2. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 3. Click the Applications & Gaming tab, then click the Single Port Forwarding page.4. Select the type of application from the Application Name drop-down list. One of the more common types to select is HTTP, but see your device’s documentation for recommendations. 5. In the To IP Address field, enter the last three digits of the IP address you have reserved for the computer you want to forward Internet traffic to. The rest of the IP address has already been completed for you. 6. Select Enabled next to the IP Address field.7. Click Save Changes at the bottom of the screen.TIPFor other devices not included in the Application Name drop-down list, see the device’s documentation for port and protocol information.Port Forwarding and Port Triggering

52Port Forwarding and Port TriggeringLinksys E-SeriesHow to set up port forwarding for multiple portsWhy would I set up port forwarding for multiple ports? Port forwarding is a feature that forwards inbound traffic from the Internet on a specific port to a single device on your local network. Unlike a web camera that typically only requires a single port to be forwarded, some applications require forwarding of multiple ports. VNC (Virtual Network Computing) software that allows you to operate your computer remotely from anywhere on the Internet is an example of an application that requires multiple ports to be forwarded. To forward to multiple ports, just create additional entries to forward additional ports to the same IP address.Example: You want to set up your computer so you can remotely access it using VNC software. By default, VNC uses TCP ports 5800 and 5900.To set up single port forwarding for multiple ports:Applications & Gaming > Single Port Forwarding1. Make sure that the software you want to use has been installed onto a networked computer.2. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 3. Set up DHCP reservation for the IP address of the computer on which you installed the software. (See “How to set up the DHCP server on your router” on page 25).4. Click the Applications & Gaming tab, then click the Single Port Forwarding page.5. For each entry, enter a descriptive name in the Application Name field.6. For each entry, enter in the same port number for the External Port and the Internal Port.7. In the To IP Address field, enter the last three digits of the IP address you have reserved for the computer you want to forward Internet traffic to. The rest of the IP address has already been completed for you. 8. Select Enabled next to the IP Address field.9. Click Save Changes at the bottom of the screen.NOTEIf you want to use software such as VNC on multiple computers, you will need to reconfigure the default ports that VNC uses on each additional computer. Then, create additional port forwarding entries for each additional computer. See your software’s documentation for help.How to set up port forwarding for a range of portsWhy would I set up port forwarding for a range of ports? Port forwarding is a feature that forwards inbound traffic from the Internet on a range of ports to a single device on your local network. Unlike a web camera that typically only requires a single port to be forwarded, some applications require forwarding to a range of ports. Example: You want to set up your computer so you can use BitTorrent, a popular peer-to-peer file sharing application. BitTorrent uses port 6881 by default. If that port is busy, the requesting BitTorrent client tries the next port in sequence. The most common configuration for home routers with a single BitTorrent computer is to set up port forwarding using a range of ports starting with 6881 and ending with port 6889.

53Port Forwarding and Port TriggeringLinksys E-SeriesTo set up port range forwarding:Applications & Gaming > Port Range Forwarding1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Set up a DHCP reservation for the IP address of the computer on which you installed the software. (See “How to set up the DHCP server on your router” on page 25). In this example, the IP address of the desktop computer with BitTorrent installed is 192.168.1.140. 3. Click the Applications & Gaming tab, then click the Port Range Forwarding page.4. Enter a descriptive name, then enter the Start Port and the End Port values to specify the range. In this example, the range is 6881 to 6889. 5. Select TCP as the protocol. 6. In the To IP Address field, enter the last 3 digits of the IP address of the device running the software. The rest of the IP address fields already completed. In this example, you would enter 140. 7. Select Enabled next to the To IP Address field.8. Click Save Settings at the bottom of the page.NOTES:To use software like BitTorrent on multiple computers on your network, create additional entries with a unique range of ports as shown above. BitTorrent only works with ports between 6881 and 6999.Depending on your computer’s firewall software, you may need to open a range of ports in your firewall to enable software that uses port range forwardingHow to set up port range triggering for online gamingFor ALLWhy would I use port triggering instead of port forwarding? Port range triggering allows the router to watch outgoing data for specific port numbers. The IP address of the computer that sends the matching data is remembered by the router, so that when the requested data returns through the router, the data is routed back to the proper computer. An example of port range triggering would be to enable a USB or Bluetooth headset for online chat and gaming.To set up port range triggering for multiple entries: Applications & Gaming > Port Range Triggering1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Applications & Gaming tab, then click the Port Range Triggering page.3. See your device documentation for information on the ports that the device uses.4. For each entry in the Port Range Forwarding table: • Enter a descriptive name (such as PS3 Headset) • For single ports, enter the same port number in each Triggered Range and Forwarded Range box. • For port ranges, enter the same number ranges in each Triggered Range and Forwarded Range column.5. Click Save Settings at the bottom of the page.

54Port Forwarding and Port TriggeringLinksys E-SeriesHow to configure your Xbox for online gamingFor ALLWhy would I set up my Xbox for online gaming? Online gaming adds another dimension to using your Xbox. As with other online gaming applications and gaming consoles, you need to forward multiple ports to use your Xbox for online gaming. The procedure for setting up your Xbox is almost identical to setting up multiple port forwarding for VNC remote control. (See “How to set up port forwarding for multiple ports” on page 52).NOTEFor more information on configuring your router for online gaming, see “How to optimize your router for gaming and voice” on page 28.Refer to your game console documentation to determine the ports used by your device. The Xbox uses four ports: • TCP port 80 • UDP port 88 • TCP/UDP port 53 • TCP/UDP port 3074To set up an Xbox using multiple entries of single port forwarding: Applications & Gaming > Single Port Forwarding1. Connect your Xbox 360 to your router.1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Set up a DHCP reservation for the IP address of the Xbox. (See “How to set up the DHCP server on your router” on page 25). – OR –Refer to your game console’s documentation to set a static IP address for your device. 3. Click the Applications & Gaming tab, then click the Single Port Forwarding page. The Xbox uses four ports, so create four port forwarding entries on this page.4. Enter the port and protocol information as shown in the image below. 5. In the To IP Address field, enter a 1- to 3-digit number that corresponds to the last three digits of the IP Address of the Xbox 360. The rest of the IP address is already completed. 6. Select Enabled next to the To IP Address field for each entry.7. Click Save Settings at the bottom of the page.

55Maintaining and MonitoringLinksys E-Series55How to back up and restore your router configurationFor ALLWhy do I need to back up my router configuration? As with any valuable data, you should back up your router configuration. Your router might contain many customized settings. Those settings would be lost if you reset your router to its factory defaults, and you would need to re-enter all of them manually. If you back up your router configuration, restoring settings is easy.To back up your router configuration:Administration > Management1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Administration tab, then click the Management page.3. Click Back Up Configurations at the bottom of the screen.You are prompted to save the file.4. Click OK or Save.5. Specify a file location, then click Save.To restore your router configuration:Administration > Management1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Administration tab, then click the Management page.3. Click Restore Configurations at the bottom of the screen.A separate window opens. 4. Click Browse to navigate to the location of your configuration file, then select the file and click Open. 5. To restore the configuration, click Start to Restore.How to restore factory defaultsWhy would I need to restore to factory defaults? If you are experiencing difficulties with the router and have exhausted all other troubleshooting measures, you may want to reset the router to factory defaults. Resetting the router erases all of your settings, so you must restore the settings after. We recommend that you back up your configuration before resetting your router to factory defaults. See “How to back up and restore your router configuration” on page 55.You can use the Reset button or the router’s browser-based utility to restore your router to factory defaults.Maintaining and Monitoring

56Maintaining and MonitoringLinksys E-SeriesTo reset your router to factory defaults with the reset button:1. With your router connected to power and turned on, press and hold the Reset button on the bottom of your router for 5-10 seconds.E1200, E1500, E2500, and E3200 Reset ButtonE4200 Reset ButtonTo reset your router to factory defaults using the browser-based utility:Administration > Factory Defaults1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Administration tab, then click the Factory Defaults page.3. Click Restore Factory Defaults.A confirmation window opens. 4. Click OK.How to upgrade the router’s firmwareFor ALLWhy would I need to upgrade my router’s firmware? Linksys may periodically publish a firmware upgrade either to fix a problem or to add features to your router. IMPORTANTDo not interrupt the upgrade process. You should not turn off the router or press the Reset button during the upgrade. Doing so may permanently disable the router.If you are upgrading from a laptop computer, make sure that the laptop is connected to a power source or that the battery is fully charged.Disable your computer’s Sleep mode. It might interrupt the upgrade process.If you are upgrading from a computer with a wireless network connection, make sure that you have strong wireless signal strength. If not, move your computer closer to your router.TIPSEach time you run Cisco Connect, it checks for software updates and installs them, if available. Use the following instructions only if you don’t run Cisco Connect.

57Maintaining and MonitoringLinksys E-SeriesTo upgrade the router’s firmware:Linksys.com/support Administration > Firmware Upgrade1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22).2. Click the Status tab, then click the Router page and take note of the current firmware version for your router.3. Using your web browser, connect to Linksys.com/support, then find your router model.4. Click the Downloads tab, then select the hardware version for your router from the Select Hardware Version drop-down list.5. Compare the latest available firmware version on the website with your current version. If there is a newer version, click Release Notes to see if the newer version contains new features you want or solves a problem you are having. 6. If you want the new version, click Download and save the file to your computer. Take note of the file location.During the upgrade process, the router may lose the settings you have changed. Make a backup of your router configuration before starting the upgrade process. See “How to back up and restore your router configuration” on page 55.7. In the browser-based utility, click the Administration tab, then click the Firmware Upgrade page. 8. Click Browse, then go to the location where you saved the upgrade file.9. Select the upgrade file, then click Start Upgrade and follow the on-screen instructions. The upgrade process begins, and a progress bar appears. When the firmware has been uploaded, a new page opens with an “Upgrade is successful” notice, and the router reboots.How to check the status of your routerFor ALLWhy would I want to check the status of my router? Your router status tells you whether you have a secure Internet connection and informs you about the status of your network-connected devices.To check your router status using Cisco Connect:1. In Windows, click Start, All Programs, then click Cisco Connect. – OR –On a Mac, open the Applications folder, then click Cisco Connect.The Cisco Connect main menu opens.2. Look in the upper-right corner of the Cisco Connect main menu. If your router is online and secure, you see online secure and a green indicator.

58Maintaining and MonitoringLinksys E-SeriesTo check your router status using the browser-based utility:Status > Router Status > Local Network Status > Wireless Network Status > Ports1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Status tab, then click the Router page. Detailed information about your router status is displayed. TIPFor field descriptions, click Help on the right side of the screen.3. Click the Status tab, then click the Local Network page. Your local network’s IP address information and the DHCP server settings are displayed. 4. Click DHCP Client Table to display the currently assigned IP addresses.5. Click the Status tab, then click the Wireless Network page. Your wireless network status is displayed. 6. Click the Status tab, then click the Ports page. The link status and speed (speed data available only for the E3200 and E4200) for each of the Ethernet ports and the Internet port are displayed. How to disable the Ethernet port status lightsWhy would I want to disable the Ethernet port status lights? Depending on the placement of the router in a home, some users might find the lights distracting. You can easily disable the lights using Cisco Connect, but you can also disable them using the browser-based utility.To disable the lights using Cisco Connect:1. In Windows, click Start, All Programs, then click Cisco Connect. – OR –On a Mac, open the Applications folder, then click Cisco Connect.

59Maintaining and MonitoringLinksys E-SeriesThe Cisco Connect main menu opens.2. Under Router Settings, click Change.3. Under Port lights, click Off, then click Finish.To disable the lights using the browser-based utility:Status > Ports1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Status tab, then click the Ports page. 3. In the Rear Port Lights section, click Off, then click Save Settings.How to test your Internet connectionWhat utilities are included in my router to test my Internet connection? Your router includes two diagnostic tests, Ping and Traceroute, that let you check network connections, including network devices and your Internet connection.To diagnose your Internet connection:Administration > Diagnostics1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Administration tab, then click the Diagnostics page.3. To check whether an address can be reached, enter an IP address or URL, a packet size, and number of times to ping in the Ping Test section, then click Start to Ping.

60Maintaining and MonitoringLinksys E-SeriesA window opens showing the ping test results. You will see a response for each successful ping. NOTEIf an Internet URL fails to respond to ping, it doesn’t necessarily mean that the site is down. For security reasons, some sites are configured to not respond to ping requests.4. To trace the route that packets take between your router and a specific address, enter an address in the IP or URL Address field of the Traceroute Test section, then click Start to Traceroute.A window opens with the test results.How to configure and use logsWhat kind of logging capabilities does my router have? Your router can track all traffic for your Internet connection. Your router supports four types of logs:To enable and view router logs:Administration > Log1. Log into the browser-based utility (see “How to open the browser-based utility” on page 22). 2. Click the Administration tab, then click the Log page. 3. To monitor traffic between the local network and the Internet, select Enabled (default), then click Save Settings.4. To view the logs, click View Log. The Log window opens.

61Maintaining and MonitoringLinksys E-Series5. Select the log you want to see from the Type drop-down list. • Incoming Log—The source IP addresses and destination port numbers for incoming Internet traffic • Outgoing Log—Local IP addresses, destination URLs/IP addresses, and service/port numbers for outgoing Internet traffic • Security Log—Logins for the browser-based utility • DHCP Client Log—Local DHCP server status information6. To save the log, click Save the Log, then click OK or Save. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

62Browser-based Utility Menu StructureLinksys 62E1200/E1500SetupBasic SetupLanguageInternet SetupInternet Connection TypeOptional SettingsNetwork SetupRouter AddressDHCP Server SettingTime SettingsTime ZoneRebootDDNSDDNSDDNS ServiceMAC Address CloneMAC Address CloneAdvanced RoutingNATDynamic Routing (RIP)Static RoutingWirelessBasic Wireless SettingsConfiguration ViewWireless SecurityWireless SecurityGuest AccessGuest AccessWireless MAC FilterWireless MAC FilterAccess RestrictionMAC Address Filter ListSecurityFirewallFirewallInternet FilterWeb FilterVPN PassthroughVPN PassthroughAccess PolicyParental ControlsTarget DevicesScheduleBlock Specific SitesApplications & GamingSingle Port ForwardingSingle Port ForwardingApplication NamePort Range ForwardingPort Range ForwardingApplication NamePort Range TriggeringPort Range TriggeringDMZDMZQoSQoS (Quality of Service)WirelessInternet Access PriorityUpstream BandwidthCategorySummaryAdministrationManagementRouter AccessLocal Management AccessRemote Management AccessAdvanced featuresUPnPBack up and RestoreLogLogDiagnosticsDiagnosticsPing TestTraceroute TestFactory DefaultsFactory DefaultsFirmware UpgradeFirmware UpgradeStatusRouterRouter InformationInternet ConnectionLocal NetworkLocal NetworkDHCP ServerWireless NetworkWireless NetworkPortsRear Port LightsInternet Port LinkLocal Port LinkBrowser-based Utility Menu Structure

63Browser-based Utility Menu StructureLinksys E2500SetupBasic SetupLanguageInternet SetupInternet Connection TypeOptional SettingsNetwork SetupRouter AddressDHCP Server SettingTime SettingsTime ZoneRebootDDNSDDNSDDNS ServiceMAC Address CloneMAC Address CloneAdvanced RoutingNATDynamic Routing (RIP)Static RoutingWirelessBasic Wireless SettingsWi-Fi Protected Setup5 GHz Wireless Settings2.4 GHz Wireless SettingsConfiguration ViewWireless Security5 GHz Wireless Security2.4 GHz Wireless SecurityGuest AccessGuest AccessWireless MAC FilterWireless MAC FilterAccess RestrictionMAC Address Filter ListSecurityFirewallFirewallInternet FilterWeb FilterVPN PassthroughVPN PassthroughAccess PolicyParental ControlsTarget DevicesScheduleBlock Specific SitesApplications & GamingSingle Port ForwardingSingle Port ForwardingApplication NamePort Range ForwardingPort Range ForwardingApplication NamePort Range TriggeringPort Range TriggeringDMZDMZQoSQoS (Quality of Service)WirelessInternet Access PriorityUpstream BandwidthCategorySummaryAdministrationManagementRouter AccessLocal Management AccessRemote Management AccessAdvanced featuresUPnPBack Up and RestoreLogLogDiagnosticsDiagnosticsPing TestTraceroute TestFactory DefaultsFactory DefaultsFirmware UpgradeFirmware UpgradeStatusRouterRouter InformationInternet ConnectionLocal NetworkLocal NetworkDHCP ServerWireless Network5 GHz Wireless Network2.4 GHz Wireless NetworkPortsRear Port LightsInternet Port LinkLocal Port Link

64Browser-based Utility Menu StructureLinksys E3200SetupBasic SetupLanguageInternet SetupInternet Connection TypeOptional SettingsNetwork SetupRouter AddressDHCP Server SettingTime SettingsTime ZoneRebootDDNSDDNS ServiceMAC Address CloneAdvanced RoutingNATDynamic Routing (RIP)Static RoutingWirelessBasic Wireless SettingsWi-Fi Protected Setup5 GHz Wireless Settings2.4 GHz Wireless SettingsConfiguration ViewWireless Security5 GHz Wireless Security2.4 GHz Wireless SecurityGuest AccessWireless MAC FilterWireless MAC FilterAccess RestrictionMAC Address Filter ListSecurityFirewallFirewallInternet FilterWeb FilterVPN PassthroughStorageDiskDisk ManagementShared FolderFormat DiskFTP ServerSetupAccessAdministrationInformationAnonymous AccessUser ManagementGroup ManagementAccess PolicyParental ControlsTarget DevicesScheduleBlock Specific SitesApplications & GamingSingle Port ForwardingApplication NamePort Range ForwardingApplication NamePort Range TriggeringDMZQoSQoS (Quality of Service)WirelessInternet Access PriorityUpstream BandwidthCategorySummaryAdministrationManagementRouter AccessLocal Management AccessRemote Management AccessAdvanced featuresUPnPBack Up and RestoreLogDiagnosticsPing TestTraceroute TestFactory DefaultsFirmware UpgradeStatusRouterRouter InformationInternet ConnectionLocal NetworkLocal NetworkDHCP ServerWireless Network5 GHz Wireless Network2.4 GHz Wireless NetworkPortsRear Port LightsInternet Port LinkLocal Port Link

65Browser-based Utility Menu StructureLinksys E4200SetupBasic SetupLanguageInternet SetupInternet Connection TypeOptional SettingsNetwork SetupRouter AddressDHCP Server SettingTime SettingsTime ZoneRebootDDNSDDNS ServiceMAC Address CloneAdvanced RoutingNATDynamic Routing (RIP)Static RoutingWirelessBasic Wireless SettingsWi-Fi Protected Setup5 GHz Wireless Settings2.4 GHz Wireless SettingsConfiguration ViewWireless Security5 GHz Wireless Security2.4 GHz Wireless SecurityGuest AccessWireless MAC FilterWireless MAC FilterAccess RestrictionMAC Address Filter ListSecurityFirewallFirewallInternet FilterWeb FilterVPN PassthroughStorageDiskDisk ManagementUSB Port SpeedShared FolderFormat DiskMedia ServerUPnP Media ServerSetupDatabaseFTP ServerSetupAccessAdministrationInformationAnonymous AccessUser ManagementGroup ManagementAccess RestrictionsParental Controls + Internet Access PolicyApplications & GamingSingle Port ForwardingApplication NamePort Range ForwardingApplication NamePort Range TriggeringDMZQoSQoS (Quality of Service)WirelessInternet Access PriorityUpstream BandwidthCategorySummaryAdministrationManagementRouter AccessLocal Management AccessRemote Management AccessAdvanced featuresUPnPBack Up and RestoreLogDiagnosticsPing TestTraceroute TestFactory DefaultsFirmware UpgradeStatusRouterRouter InformationInternet ConnectionLocal NetworkLocal NetworkDHCP ServerWireless Network5 GHz Wireless Network2.4 GHz Wireless NetworkPortsRear Port LightsInternet Port LinkLocal Port Link

66SpecificationsLinksys E120066Linksys E1200Model Name Linksys E1200Description Wireless-N RouterModel Number E1200Standards 802.11n, 802.11g, 802.11b, 802.3uPorts Power, Internet, and Ethernet (1-4)Buttons Reset, Wi-Fi Protected Setup™LEDs Power/Wi-Fi Protected Setup, Internet, Ethernet (1-4)Cabling Type CAT 5eTransmitted Power 802.11n (20 MHz): 15.0 ± 1.5dBm @ CH6, MCS 0~4, MCS 8~12 13.5 ± 1.5dBm @ CH6, MCS 5~7, MCS 13~15 802.11n (40 MHz): 14.0 ± 1.5dBm @ CH6, MCS 0~4, MCS 8~12 13.5 ± 1.5dBm @ CH6, MCS 5~7, MCS 13~15 802.11g: 14.5 ± 1.5dBm @ CH6, all rates 802.11b: 16.5 ± 1.5dBm @ CH6, all ratesAntenna Gain ≤2.5 dBi, ≤4.0 dBi (2 antennas)UPnP SupportedWireless Security Wi-Fi Protected Access™ 2 (WPA2), WEP, wireless MAC ﬁlteringSecurity Key Bits Up to 128-bit encryptionEnvironmentalDimensions 7.43” × 5.97” × 1.23” (188.7 × 151.7 × 31.2 mm)Unit Weight 8.91 oz. (252.7g)Power 12V, 0.5ACertiﬁcations FCC, UL/cUL, ICES-003, RSS210, CE, Wi-Fi (IEEE 802.11b/g/n), WPA2™, WMM®, Wi-Fi Protected Setup, Windows 7Operating Temp. 32 to 104°F (0 to 40°C)Storage Temp. -4 to 140°F (-20 to 60°C)Operating Humidity 10 to 80% non-condensingStorage Humidity 5 to 90% non-condensingSpeciﬁcations are subject to change without notice.Specifications 2

67SpecificationsLinksys E1500Linksys E1500Model Name Linksys E1500Description Wireless-N Router with SpeedBoostModel Number E1500Standards 802.11n, 802.11g, 802.11b, 802.3uPorts Power, Internet, and Ethernet (1-4)Buttons Reset, Wi-Fi Protected SetupLEDs Power/Wi-Fi Protected Setup, Internet, Ethernet (1-4)Cabling Type CAT 5eTransmitted Power 802.11n (20 MHz): 17.0 ± 1.5 dBm @ CH6, MCS 0~4, MCS 8~12 16.0 ± 1.5 dBm @ CH6, MCS 5~7, MCS 13~15 802.11n (40 MHz): 15.5 ± 1.5 dBm @ CH6, MCS 0~4, MCS 8~12 14.0 ± 1.5 dBm @ CH6, MCS 5~7, MCS 13~15 802.11g: 18.0 ± 1.5 dBm @ CH6, 6 Mbps 17.0 ± 1.5 dBm @ CH6, 54 Mbps 802.11b: 18.0 ± 1.5 dBm @ CH6, all ratesAntenna Gain ≤3.0 dBi, ≤4.0 dBi, ≤4.5 dBi (3 antennas)UPnP SupportedWireless Security Wi-Fi Protected Access 2 (WPA2), WEP, wireless MAC ﬁlteringSecurity Key Bits Up to 128-bit encryptionEnvironmentalDimensions 7.43” × 5.97” × 1.23” (188.7 × 151.7 × 31.2 mm)Unit Weight 8.96 oz. (254.1g)Power 12V, 0.5ACertiﬁcations FCC, UL/cUL, ICES-003, RSS210, CE, Wi-Fi (IEEE 802.11b/g/n), WPA2, WMM, Wi-Fi Protected Setup, Windows 7Operating Temp. 32 to 104°F (0 to 40°C)Storage Temp. -4 to 140°F (-20 to 60°C)Operating Humidity 10 to 80% non-condensingStorage Humidity 5 to 90% non-condensingSpeciﬁcations are subject to change without notice.

68SpecificationsLinksys E2500Linksys E2500Model Name Linksys E2500Description Advanced Dual-Band N RouterModel Number E2500# of Antennas 4 total, 2 internal antennas per each 2.4 GHz & 5 GHz radio bandDetachable (y/n) No Modulation 802.11b: CCK, QPSK, BPSK 802.11g: OFDM 802.11a: OFDM 802.11n: BPSK, QPSK, 16-QAM, 64-QAM Receive Sensitivity 2.4 GHz (Typical) 802.11b: -87 dBm @ 11 Mbps 802.11g: -70 dBm @ 54 Mbps 802.11n 20 MHz: -70 dBm @ MCS15 802.11n 40 MHz: -66 dBm @ MCS15 5 GHz 802.11a: -70 dBm @ 54 Mbps 802.11n 20 MHz: -66 dBm @ MCS23 802.11n 40 MHz: -62 dBm @ MCS23Antenna Gain in dBi 2.4 GHz: Antenna 1 (right rear): ≤2.94 dBi Antenna 2 (front right): ≤3.78 dBi 5 GHz: Antenna 1 (right front): ≤5.86 dBi Antenna 2 (front left): ≤4.88 dBiUPnP SupportedSecurity features WEP, WPA, WPA2Security key bits Up to 128-bit encryptionEnvironmentalDimensions 8.86” x 1.38” x 7.09” (225 x 35 x 180 mm)Unit Weight 15.94 oz (452 g)Power 12V, 1ACertiﬁcations FCC, IC, CE, Wi-Fi A/B/G/N Operating Temp. 32 to 104°F (0 to 40°C)Storage Temp. -4 to 140°F (-20 to 60°C)Operating Humidity 10 to 80%, relative humidity, non-condensingStorage Humidity 5 to 90% non-condensingSpeciﬁcations are subject to change without notice.

69SpecificationsLinksys E3200Linksys E3200Model Name Linksys E3200Description High Performance Dual-Band N RouterModel Number E3200# of Antennas 6 total, 3 internal antennas per each 2.4 GHz & 5 GHz radio bandDetachable (y/n) No Switch Port Speed 10/100/1000 MbpsPorts Internet, Ethernet (1-4), USB, PowerButtons Reset, Wi-Fi Protected SetupLEDs Power, Ethernet (1-4)Modulation 802.11b: CCK, QPSK, BPSK 802.11g: OFDM 802.11a: OFDM 802.11n: BPSK, QPSK, 16-QAM, 64-QAM Receive Sensitivity 2.4 GHz 802.11b: -87 dBm @ 11 Mbps (Typical) 802.11g: -77 dBm @ 54 Mbps (Typical) 802.11n (20 MHz): -71 dBm @ MCS15 (Typical) 802.11n (40 MHz): -68 dBm @ MCS15 (Typical) 5 GHz 802.11a: -75 dBm @ 54 Mbps (Typical) 802.11n 20 MHz: -70 dBm @ MCS15 (Typical) 802.11n 40 MHz: -67 dBm @ MCS15 (Typical)Antenna Gain 2.4 GHz (Dipole Antennas) Antenna 1 ≤ 3 dBi Antenna 2 ≤ 4 dBi Antenna 3 ≤ 4 dBi 5 GHz (Dipole Antennas) Antenna 1 ≤ 4.5 dBi Antenna 2 ≤ 4.5 dBi Antenna 3 ≤ 4.5 dBi UPnP SupportedSecurity features WEP, WPA, WPA2 Security key bits Up to 128-bit encryptionStorage File System Support FAT, and NTFS, and HFS+EnvironmentalDimensions 6.69” x 0.98” x 7.48” (170 x 25 x 190 mm)Unit Weight 7.62 oz (216 g)Power 12V, 2ACertiﬁcations FCC, IC, CE, Wi-Fi A/B/G/N Operating Temp. 32 to 95°F (0 to 35°C)Storage Temp. -4 to 140°F (-20 to 60°C)Operating Humidity 10 to 80% relative humidity, non-condensingStorage Humidity 5 to 90% non-condensingSpeciﬁcations are subject to change without notice.

70SpecificationsLinksys E4200Linksys E4200Model Name Linksys E4200Description Maximum Performance Wireless-N RouterModel Number E4200Standards 802.11n, 802.11a, 802.11g, 802.11b, 802.3, 802.3u, 802.3abRadio Frequency 2.4 and 5 GHzSwitch Port Speed 10/100/1000 Mbps (Gigabit Ethernet)Ports Power, USB, Internet, Ethernet (1-4)Buttons Reset, Wi-Fi Protected SetupLEDs Top panel: Power Back panel: Internet, Ethernet (1-4)Number of Antennas 6 total, 3 internal antennas per each 2.4 GHz and 5 GHz radio bandDetachable (y/n) NoModulations 802.11b: CCK, QPSK, BPSK 802.11g: OFDM 802.11a: OFDM 802.11n: BPSK, QPSK, 16-QAM, 64-QAMReceive Sensitivity 2.4 GHz 802.11b: -87 dBm @ 11 Mbps (Typical) 802.11g: -77 dBm @ 54 Mbps (Typical) 802.11n: 20 MHz: -71 dBm @ MCS15 (Typical) 802.11n: 40 MHz: -68 dBm @ MCS15 (Typical) 5 GHz 802.11a: -71 dBm @ 54 Mbps (Typical) 802.11n: 20 MHz: -70 dBm @ MCS23 (Typical) 802.11n: 40 MHz: -68 dBm @ MCS23 (Typical)Antenna Gain in dBi 2.4 GHz (3 internal PIFA antennas) PIFA 1 ≤ 3.6 dBi (Right) PIFA 2 ≤ 3.8 dBi (Left) PIFA 3 ≤ 3.8 dBi (Front) 5 GHz (3 internal PIFA antennas) PIFA 1 ≤ 4.8 dBi (Right) PIFA 2 ≤ 5.3 dBi (Left) PIFA 3 ≤ 5.2 dBi (Front)Supported File Systems for Storage Device FAT32, NTFS, and HSF+UPnP SupportedSecurity Features WEP, WPA, WPA2Security Key Bits Up to 128-bit encryptionEnvironmentalDimensions 8.86” x 0.98” x 6.30” (225 x 25 x 160 mm)Unit Weight 12.52 oz (355 g)Power 12V, 2ACertiﬁcations FCC, IC, CE, Wi-Fi a/b/g/n, Windows 7Operating Temp. 32 to 104°F (0 to 40°C)Storage Temp. -4 to 140°F (-20 to 60°C)Operating Humidity 10 to 80% relative humidity, non-condensingStorage Humidity 5 to 90% non-condensingSpeciﬁcations are subject to change without notice.