LINKSYS WAP610N Wireless-N Access Point with Dual-Band User Manual WAP610N User Guide

Download:
Mirror Download [FCC.gov]
Document ID	1110054
Application ID	CnJnFyqCY6ffhQ1xHObAFw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	213.81kB (2672613 bits)
Date Submitted	2009-05-13 00:00:00
Date Available	2009-05-13 00:00:00
Creation Date	2009-04-13 18:53:54
Producing Software	Adobe PDF Library 9.0
Document Lastmod	2009-05-13 16:42:08
Document Title	WAP610N User Guide
Document Creator	Adobe InDesign CS4 (6.0)
Document Author:	Linksys by Cisco

USER GUIDE
Ultra RangePlus Wireless-N
Access Point with Dual-Band
Model:
WAP610N
About This Guide
About This Guide
Icon Descriptions
While reading through the User Guide you may see
various icons that call attention to specific items. Below is
a description of these icons:
NOTE: This check mark indicates that there is
a note of interest and is something that you
should pay special attention to while using the
product.
WARNING: This exclamation point indicates
that there is a caution or warning and it is
something that could damage your property or
product.
WEB: This globe icon indicates a noteworthy
website address or e-mail address.
Online Resources
Website addresses in this document are listed without
http:// in front of the address because most current web
browsers do not require it. If you use an older web browser,
you may have to add http:// in front of the web address.
Resource
Website
Linksys
www.linksysbycisco.com
Linksys
International
www.linksysbycisco.com/international
Glossary
www.linksysbycisco.com/glossary
Network
Security
www.linksysbycisco.com/security
Copyright and Trademarks
Linksys, Cisco and the Cisco Logo are
registered trademarks or trademarks of
Cisco Systems, Inc. and/or its affiliates in
the U.S. and certain other countries. Other
brands and product names are trademarks
or registered trademarks of their respective
holders. Copyright © 2009 Cisco Systems,
Inc. All rights reserved.
Ultra RangePlus Wireless-N Access Point with Dual-Band
Table of Contents
Chapter 1:
Product Overview
LEDs Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ports Panel .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 1
Chapter 2:
Wireless Security Checklist
General Network Security Guidelines  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Additional Security Tips  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Chapter 3:
Advanced Configuration
Setup > Basic Setup .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3
Wireless > Basic Wireless Settings .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Wireless > Wireless Security .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5
Wireless > Wireless MAC Filter .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7
Wireless > WMM®  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8
Wireless > Advanced Wireless Settings .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 11
Administration > Management .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 12
Administration > Factory Defaults  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 12
Administration > Firmware Upgrade .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 13
Status > Access Point .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 13
Status > Wireless Network .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 13
Status > About .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 13
Appendix A:
Troubleshooting
14
Appendix B:
Specifications
15
Appendix C:
Warranty Information
16
Limited Warranty  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 16
Appendix D:
Regulatory Information
18
FCC Statement .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 18
FCC Radiation Exposure Statement .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 18
Safety Notices .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 18
Industry Canada Statement .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 19
Restrictions in the 5 GHz Band .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 19
Avis d’Industrie Canada .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 19
Restrictions dans la bande 5 GHz .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 19
Wireless Disclaimer  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 20
Avis de non-responsabilité concernant les appareils sans fil  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 20
Ultra RangePlus Wireless-N Access Point with Dual-Band
ii
Table of Contents
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste
Electric and Electronic Equipment (WEEE)  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 21
Appendix E: Software End User License Agreement
25
Cisco Products .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 25
Software Licenses .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 25
Ultra RangePlus Wireless-N Access Point with Dual-Band
iii
Product Overview
Chapter 1
Chapter 1:
Product Overview
Thank you for choosing the Linksys by Cisco
Ultra RangePlus Wireless-N Access Point with Dual-Band.
TBD TBD TBD.
Ethernet (Blue) The Ethernet LED lights up
when there is a wired connection. The LED
flashes when the Access Point is actively sending
or receiving data over the Ethernet port.
Power (Blue) The Power LED lights up when
the Access Point is powered on.
Ports Panel
LEDs Panel
Ethernet The Ethernet port connects the
Access Point to a router.
Wireless (Blue) The Wireless LED lights up
when there is a wireless connection. The LED
flashes when the Access Point is actively sending
or receiving data over the wireless network.
Wi-Fi Protected Setup Button If your router
supports Wi-Fi Protected Setup and uses
WPA or WPA2 security, then you can use Wi-Fi
Protected Setup to automatically connect the
Access Point. To use Wi-Fi Protected Setup, run
the Setup Wizard, or refer to Wireless > Basic
Wireless Settings, page 4.
Reset There are two ways to reset the Access
Point’s factory defaults. Either press and
hold the Reset button for approximately
five seconds, or restore the defaults from
Administration > Factory Defaults in the Access
Point’s web-based utility.
Power The Power port connects the Access
Point to the included power adapter.
Wi-Fi Protected Setup LED (Blue/Amber) The
LED flashes blue for two minutes during Wi-Fi
Protected Setup. It lights up blue when wireless
security is enabled. If there is an error during
the Wi‑Fi Protected Setup process, then the LED
lights up amber. Make sure the network router
supports Wi‑Fi Protected Setup. Wait until the
LED is off, and then try again.
Ultra RangePlus Wireless-N Access Point with Dual-Band
Wireless Security Checklist
Chapter 2
Chapter 2:
Wireless Security Checklist
Wireless networks are convenient and easy to install, so
homes with high-speed Internet access are adopting them
at a rapid pace. Because wireless networking operates by
sending information over radio waves, it can be more
vulnerable to intruders than a traditional wired network.
Like signals from your cellular or cordless phones, signals
from your wireless network can also be intercepted. Since
you cannot physically prevent someone from connecting
to your wireless network, you need to take some additional
steps to keep your network secure.
1. Change the default wireless
network name or SSID
Wireless devices have a default wireless network name
or Service Set Identifier (SSID) set by the factory. This
is the name of your wireless network, and can be up
to 32 characters in length. Linksys wireless products
use linksys as the default wireless network name. You
should change the wireless network name to something
unique to distinguish your wireless network from other
wireless networks that may exist around you, but do not
use personal information (such as your Social Security
number) because this information may be available for
anyone to see when browsing for wireless networks.
2. Change the default password
For wireless products such as access points and routers,
you will be asked for a password when you want to change
their settings. These devices have a default password set
by the factory. The Linksys default password is admin.
Hackers know these defaults and may try to use them
to access your wireless device and change your network
settings. To thwart any unauthorized changes, customize
the device’s password so it will be hard to guess.
3. Enable MAC address filtering
Linksys routers give you the ability to enable Media Access
Control (MAC) address filtering. The MAC address is a
unique series of numbers and letters assigned to every
networking device. With MAC address filtering enabled,
wireless network access is provided solely for wireless
devices with specific MAC addresses. For example, you can
specify the MAC address of each computer in your home
so that only those computers can access your wireless
network.
Ultra RangePlus Wireless-N Access Point with Dual-Band
4. Enable encryption
Encryption protects data transmitted over a wireless
network. Wi-Fi Protected Access (WPA/WPA2) and Wired
Equivalent Privacy (WEP) offer different levels of security
for wireless communication.
A network encrypted with WPA/WPA2 is more secure
than a network encrypted with WEP, because WPA/WPA2
uses dynamic key encryption. To protect the information
as it passes over the airwaves, you should enable the
highest level of encryption supported by your network
equipment.
WEP is an older encryption standard and may be the
only option available on some older devices that do not
support WPA.
General Network Security Guidelines
Wireless network security is useless if the underlying
network is not secure.
•• Password protect all computers on the network and
individually password protect sensitive files.
•• Change passwords on a regular basis.
•• Install anti-virus software and personal firewall
software.
•• Disable file sharing (peer-to-peer). Some applications
may open file sharing without your consent and/or
knowledge.
Additional Security Tips
•• Keep wireless routers, access points, or modem routers
away from exterior walls and windows.
•• Turn wireless routers, access points, or modem routers
off when they are not being used (at night, during
vacations).
•• Use strong passphrases that are at least eight characters
in length. Combine letters and numbers to avoid using
standard words that can be found in the dictionary.
WEB: For more information on wireless security,
visit www.linksysbycisco.com/security
Chapter 3
Chapter 3:
Advanced Configuration
After setting up the Access Point with the Setup Wizard
(located on the CD-ROM), the Access Point will be ready
for use. However, if you want to change its advanced
settings, use the Access Point’s web-based utility. This
chapter describes each web page of the utility and each
page’s key functions. You can access the utility via a web
browser on a computer networked with the Access Point.
Advanced Configuration
1. In the IP address field, enter 169.254.x.y (x should
be replaced by a number between 1 and 254, and y
should be replaced by a number between 0 and 255).
2. In the Subnet mask field, enter 255.255.0.0.
NOTE: The steps to assign a static IP address to
the Ethernet adapter on your computer vary by
operating system. For instructions, please refer
to the help documentation of your specific
operating system.
The web-based utility has these main tabs: Setup,
Wireless, Administration, and Status. Additional tabs will
be available after you click one of the main tabs.
After you have assigned your Ethernet adapter with a static
IP address, launch your web browser, and enter the Access
Point’s IP address (the default setting is 169.254.1.226) in
the Address field. Press Enter.
How to Access the Web-Based Utility
A password request screen appears. (Non-Windows XP
users will see a similar screen.) Leave the User name field
blank. Enter the password you created during the Setup
Wizard. If you did not create a new password, use the
default password admin. (You can set a new password
from the Administration > Management screen.) Click OK
to continue.
Use a web browser to access the web-based utility.
If the Access Point is connected to a network with a DHCP
server (usually the network router), then the Access Point
will obtain its IP address from the DHCP server. If there is
no DHCP server, then the Access Point will use its default
static IP address, 169.254.1.226. (If you set a permanent
static IP address on the Access Point through the webbased utility, then enter the static IP address instead.)
NOTE: If you do not know the Access Point’s
IP address, then find its IP address in the
DHCP clients table of your router. (Refer to the
documentation for your router.)
If you cannot locate the Access Point’s IP address,
you can reset the Access Point; press the Reset
button on the Access Point for approximately
five seconds, using a straightened paper clip.
This will reset the Access Point back to the
factory default settings. The Access Point will
request an IP address from the DHCP server
(usually the network router). If no DHCP server is
found, then the Access Point will use its default
static IP address, 169.254.1.226, until it detects
a DHCP server and is assigned a dynamic IP
address.
Password Screen
NOTE: If the password request screen does not
appear, wait two minutes and try again.
Setup > Basic Setup
The first screen that appears is the Basic Setup screen. Use
this screen to change the web-based utility’s language,
or to change the Access Point’s wired, Ethernet network
settings.
If the Access Point is not associated with a router and is
using the factory default settings, connect a computer
to the Access Point using an Ethernet connection to
access the web‑based utility. You will need to configure
the Ethernet connection on the computer with a static IP
address and subnet mask.
The IP address of your Ethernet adapter should be set to a
specific IP address.
Ultra RangePlus Wireless-N Access Point with Dual-Band
Setup > Basic Setup (Automatic Configuration - DHCP)
Advanced Configuration
Chapter 3
Wi-Fi Protected Setup and uses WPA or WPA2 security,
then you can use Wi‑Fi Protected Setup to automatically
connect the Access Point.
Configuration
View To
manually
configure
your wireless network, select Manual. Refer to
Basic Wireless Settings (Manual), page 4. To use Wi-Fi
Protected Setup, select Wi-Fi Protected Setup. Refer to
Wi-Fi Protected Setup™, page 7.
Basic Wireless Settings (Manual)
Setup > Basic Setup (Static IP)
Language
Language This is used to set the language displayed by
the web-based utility. Select the desired language from
the drop-down menu.
Network Setup
This section determines if the Access Point’s IP address is
obtained automatically from a DHCP server, such as your
network router (Automatic Configuration - DHCP), or set
manually (Static IP).
Access Point IP If your network has a DHCP server,
such as your network router, assigning IP addresses to
your network devices, then keep the default, Automatic
Configuration - DHCP. The Access Point will request an IP
address from the DHCP server (usually the network router).
If no DHCP server is found, then the Access Point will use
its default static IP address, 169.254.1.226, until it detects
a DHCP server and is assigned a dynamic IP address.
If you want to set a permanent static IP address for the
Access Point, then select Static IP.
If you select Static IP, then complete the following fields:
•• Static IP Address Enter a unique IP address that will
be used to access the web-based utility.
•• Subnet Mask Enter the subnet mask of your wired
network.
•• Default Gateway Enter the IP address of the default
gateway for your network (in most cases, this is your
router).
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless > Basic Wireless Settings
Use the Basic Wireless Settings screen to configure the
Access Point’s basic wireless and security settings.
There are two ways to configure the Access Point’s
settings, manual and Wi-Fi Protected Setup™. Wi-Fi
Protected Setup™ is a feature that makes it easy to set up
your wireless network. If your network router supports
Ultra RangePlus Wireless-N Access Point with Dual-Band
Wireless > Basic Wireless Settings (Manual)
Wireless Band This is used to select the 2.4 GHz or 5.0
GHz band.
Network Mode (5 GHz) From this drop-down menu,
you can select the wireless standards running on your
network. If you have only Wireless-A devices in your
network, keep the default setting, Wireless-A Only. If
you have Wireless-N, Wireless-G, and Wireless-B devices in
your network, select Mixed.
Network Mode (2.4 GHz) From this drop-down menu,
you can select the wireless standards running on your
network. If you have only Wireless-B and Wireless-G devices
in your network, keep the default setting, Wireless-B/G
Only. If you have Wireless-N, Wireless-G, and Wireless-B
devices in your network, select Mixed.
Network Name (SSID) The SSID is the network name
shared among all points in a wireless network. The SSID
must be identical for all devices in the wireless network. It
is case-sensitive and must not exceed 32 characters (use
any characters on the keyboard). Make sure this setting
is the same for all Access Points in your wireless network.
For added security, you should change the default SSID
(linksys) to a unique name.
Channel Width For best performance in a Wireless-N
network, select 40MHz only. For Wireless-G and Wireless-B
networking only, keep the default, 20MHz only. If you
Advanced Configuration
Chapter 3
are not sure which option to use, select Auto (20MHz or
40MHz).
Wide Channel If you selected 40 MHz for the Channel
Width setting, then this setting will be available for your
primary Wireless-N channel. Select any channel from the
drop-down menu. If you are not sure which channel to
select, keep the default, Auto.
Standard Channel If you selected 20 MHz Only for the
Channel Width setting, then this setting will be available.
Select any channel from the drop-down menu. If you are
not sure which channel to select, keep the default, Auto.
SSID Broadcast When wireless clients survey the local
area for wireless networks to associate with, they will detect
the SSID broadcast by the Access Point. To broadcast the
Access Point’s SSID, keep the default setting, Enabled. If
you do not want to broadcast the Access Point’s SSID, then
select Disabled.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless > Wireless Security
The Access Point supports the following wireless security
options: WPA Personal, WPA2 Personal, WPA Enterprise,
WPA2 Enterprise, and WEP. WPA (Wi‑Fi Protected Access)
and WPA2 are stronger security methods than WEP (Wired
Equivalent Privacy). For more information about wireless
security, refer to Chapter 2: Wireless Security Checklist,
page 2.
Security Mode > WPA Personal
Encryption WPA supports the TKIP encryption method,
with dynamic encryption keys.
Passphrase Enter the key shared by the Access Point
and your wireless router or access point. It must have 8-63
characters.
Key Renewal Enter a Key Renewal period, which
instructs the Access Point how often it should change the
encryption keys. The default Key Renewal period is 3600
seconds.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
WPA2 Personal
WPA2 is a more advanced, more secure version of WPA.
Security Mode
Select the security method for your wireless network. If
you do not want to use wireless security, keep the default,
Disabled.
NOTE: Remember that each device in your
wireless network MUST use the same security
method and passphrase/key, or else the wireless
devices will not be able to communicate with
each other.
WPA Personal
WPA is a security standard stronger than WEP encryption.
Security Mode > WPA2 Personal
Encryption WPA2 supports two encryption methods,
TKIP and AES, with dynamic encryption keys. Select the
encryption method, AES or TKIP or AES. The default
selection is AES.
Passphrase Enter the key shared by the Access Point
and wireless router or access point. It must have 8-63
characters.
Key Renewal Enter a Key Renewal period, which
instructs the Access Point how often it should change the
encryption keys. The default Key Renewal period is 3600
seconds.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Ultra RangePlus Wireless-N Access Point with Dual-Band
Advanced Configuration
Chapter 3
WPA Enterprise
This option features WPA used in coordination with a
RADIUS server. (This should only be used when a RADIUS
server is connected to the Router.)
RADIUS Port Enter the port number of the RADIUS server.
The default value is 1812.
Shared Secret Enter the key shared between the Router
and the server.
Key Renewal Enter a Key Renewal period, which
instructs the Access Point how often it should change the
encryption keys. The default Key Renewal period is 3600
seconds.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
WEP
WEP is a basic encryption method, which is not as secure
as WPA or WPA2.
Security Mode > WPA Enterprise
RADIUS Server Enter the IP Address of the RADIUS
server.
RADIUS Port Enter the port number of the RADIUS server.
The default value is 1812.
Shared Secret Enter the key shared between the Router
and the server.
Key Renewal Enter a Key Renewal period, which
instructs the Access Point how often it should change the
encryption keys. The default Key Renewal period is 3600
seconds.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Security Mode > WEP
Encryption Select a level of WEP encryption, 40/64 bits
(10 hex digits) or 104/128 bits (26 hex digits). The
default is 40/64 bits (10 hex digits).
Key 1 Enter the WEP key of your network.
WPA2 Enterprise
This option features WPA2 used in coordination with a
RADIUS server. (This should only be used when a RADIUS
server is connected to the Router.)
Tx Key Key 1 is the transmit key used by the Access
Point.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Security Mode > WPA2 Enterprise
Encryption WPA2 supports two encryption methods,
TKIP and AES, with dynamic encryption keys. Select the
encryption method, AES or TKIP or AES. The default
selection is AES.
RADIUS Server Enter the IP Address of the RADIUS
server.
Ultra RangePlus Wireless-N Access Point with Dual-Band
Advanced Configuration
Chapter 3
Wi-Fi Protected Setup™
There are three methods available. Use the method that
applies to the client device you are configuring.
1. On the client’s Wi-Fi Protected Setup screen, enter the
PIN number listed on the Access Point’s Wi-Fi Protected
Setup screen. Then click Register or the appropriate
button. (The PIN number is also listed on the label on
the bottom of the Access Point.)
2. On the Access Point’s Wi-Fi Protected Setup screen,
click OK.
3. After the client device has been configured, click
OK. Then refer back to your client device or its
documentation for further instructions
The Wi-Fi Protected Setup Status, Wireless Band, Network
Name (SSID), and Security method are displayed at the
bottom of the screen.
Wireless > Wireless MAC Filter
Wireless access can be filtered by using the MAC addresses
of the wireless devices transmitting within your network’s
radius.
Wireless > Basic Wireless Settings (Wi-Fi Protected Setup)
Method #1
Use this method if your client device has a Wi-Fi Protected
Setup button.
1. Click or press the Wi-Fi Protected Setup button on
the client device.
2. Within two minutes, click the Wi‑Fi Protected Setup
button on the Access Point’s Wi-Fi Protected Setup
screen.
3. After the client device has been configured, click
OK. Then refer back to your client device or its
documentation for further instructions
The Wi-Fi Protected Setup Status, Wireless Band, Network
Name (SSID), and Security method are displayed at the
bottom of the screen.
Method #2
Use this method if your client device has a Wi-Fi Protected
Setup PIN number.
1. Enter the PIN number in the field on this screen.
2. Click Register.
3. After the client device has been configured, click
OK. Then refer back to your client device or its
documentation for further instructions
The Wi-Fi Protected Setup Status, Wireless Band, Network
Name (SSID), and Security method are displayed at the
bottom of the screen.
Method #3
Use this method if your client device requests the Access
Point’s PIN number.
Ultra RangePlus Wireless-N Access Point with Dual-Band
Wireless > Wireless MAC Filter
Wireless MAC Filter
Enabled/Disabled To filter wireless users by MAC
Address, either permitting or blocking access, select
Enabled. If you do not wish to filter users by MAC Address,
keep the default setting, Disabled.
Access Restriction
Prevent Select this to block wireless access by MAC
Address. This option is selected by default.
Permit Select this to allow wireless access by MAC
Address. This option is not selected by default.
Advanced Configuration
Chapter 3
MAC Address Filter List
Wireless Client List Click this to open the Wireless Client
List screen.
Wireless Client List
Wireless Client List
Wireless > WMM
This screen shows computers and other devices on the
wireless network. The list can be sorted by MAC Address
and Status.
Select Save to MAC Address Filter List for any device
you want to add to the MAC Address Filter List. Then click
Add.
To retrieve the most up-to-date information, click Refresh.
To return to the Wireless MAC Filter screen, click Close.
MAC 01-32 Enter the MAC addresses of the devices
whose wireless access you want to block or allow.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless > WMM®
Configure the Wireless MultiMedia (WMM) settings. WMM
prioritizes packets depending on their respective access
mode (traffic type): Background, Best Effort, Video, or
Voice. These settings should only be adjusted by an expert
administrator as incorrect settings can reduce wireless
performance.
NOTE: The settings on the WMM screen are
designed for advanced users only.
WMM®
Access Mode
You can assign different settings to the four access
modes available. Select the mode you want to configure:
Background, Best Effort, Video, or Voice. Follow the
instructions for the mode you select.
Background
Use Aggregation This option defines whether or not the
Media Access Control (MAC) layer will set up an Add Block
Acknowledgement (ADDBA) session. The default is No.
Select Yes to enable this option.
Accept Aggregation This option defines whether or not
the MAC layer will accept an ADDBA request. The default
is Yes. Select No to disable this option.
Max. Number of Packets in Aggregation This option
defines the maximum number of packets (sub-frames) in
the aggregate. The range is 0 to 7. The default is 7.
Max. Aggregation Size This option defines the maximum
size of the aggregate (in bytes). The range is 0 to 16000.
The default is 12000.
Timeout Internal This option defines the timeout
period (in time units, TU, where ITU = 1024 µs) in which
the aggregate should be closed with a “closing condition”
before it is closed by the timer. The range is 0 to 100 ms.
The default is 3.
Min. Size of Packet in Aggregation This option defines
the minimum size (in bytes) of packets to be accumulated
Ultra RangePlus Wireless-N Access Point with Dual-Band
Chapter 3
in the aggregate. The range is 0 to 1500. The default
is 10.
ADDBA Timeout This option defines the duration
after which the ADDBA setup is terminated, if there are
no frame exchanges within this duration by the Block
Acknowledgement (ACK) agreement. The range is 0 to
65535 ms. The default is 0, which disables the timeout.
Advanced Configuration
Max. Number of Packets in Aggregation This option
defines the maximum number of packets (sub-frames) in
the aggregate. The range is 0 to 10. The default is 10.
Max. Aggregation Size This option defines the
maximum size of the aggregate (in bytes). The range is 0
to 20000. The default is 16000.
Aggregation Window Size This option defines the
maximum number of packets transmitted without getting
ACKs. The range is 0 to 64. The default is 64.
Timeout Internal This option defines the timeout period
in which the aggregate should be closed with a “closing
condition” before it is closed by the timer. The range is 0 to
100 ms. The default is 3.
CW Min for STA This option defines the minimum
contention window limit from which the random backoff
is computed for an STA in BSS. The range is 15 to 1023.
The default is 15.
Min. Size of Packet in Aggregation This option defines
the minimum size (in bytes) of packets to be accumulated
in the aggregate. The range is 0 to 1500. The default
is 10.
CW Max for STA This option defines the maximum
contention window limit from which the random backoff
is computed for an STA in BSS. The range is 15 to 1023.
The default is 1023.
ADDBA Timeout This option defines the duration
after which the ADDBA setup is terminated, if there are
no frame exchanges within this duration by the Block
Acknowledgement (ACK) agreement. The range is 0 to
65535 ms. The default is 0, which disables the timeout.
AIFSN for STA This option defines the Arbitration
Interframe Space Number for an STA in BSS. The range is 0
to 15. The default is 7.
TXOP for STA This option defines the Transmission
Opportunity for an STA in BSS. The range is 0 to 8192. The
default is 0.
CW Min for AP This option defines the minimum
contention window limits from which the random backoff
is computed for AP. The range is 15 to 1023. The default
is 15.
CW Max for AP This option defines the maximum
contention window limits from which the random backoff
is computed for AP. The range is 15 to 1023. The default
is 1023.
AIFSN for AP This option defines the Arbitration
Interframe Space Number for AP. The range is 0 to 15. The
default is 7.
TXOP for AP This option defines the Transmission
Opportunity for AP. The range is 0 to 8192. The default is
0.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Best Effort
Use Aggregation This option defines whether or not the
Media Access Control (MAC) layer will set up an Add Block
Acknowledgement (ADDBA) session. The default is Yes.
Select No to disable this option.
Accept Aggregation This option defines whether or not
the MAC layer will accept an ADDBA request. The default
is Yes. Select No to disable this option.
Ultra RangePlus Wireless-N Access Point with Dual-Band
Aggregation Window Size This option defines the
maximum number of packets transmitted without getting
ACKs. The range is 0 to 64. The default is 64.
CW Min for STA This option defines the minimum
contention window limit from which the random backoff
is computed for an STA in BSS. The range is 15 to 1023.
The default is 15.
CW Max for STA This option defines the maximum
contention window limit from which the random backoff
is computed for an STA in BSS. The range is 15 to 1023.
The default is 1023.
AIFSN for STA This option defines the Arbitration
Interframe Space Number for an STA in BSS. The range is 0
to 15. The default is 3.
TXOP for STA This option defines the Transmission
Opportunity for an STA in BSS. The range is 0 to 8192. The
default is 0.
CW Min for AP This option defines the minimum
contention window limits from which the random backoff
is computed for AP. The range is 15 to 63. The default is 15.
CW Max for AP This option defines the maximum
contention window limits from which the random backoff
is computed for AP. The range is 15 to 63. The default is 63.
AIFSN for AP This option defines the Arbitration
Interframe Space Number for AP. The range is 0 to 15. The
default is 3.
TXOP for AP This option defines the Transmission
Opportunity for AP. The range is 0 to 8192. The default is
0.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Advanced Configuration
Chapter 3
Video
is computed for AP. The value is set to 15 (default) and
cannot be changed.
Use Aggregation This option defines whether or not the
Media Access Control (MAC) layer will set up an Add Block
Acknowledgement (ADDBA) session. The default is Yes.
Select No to disable this option.
AIFSN for AP This option defines the Arbitration
Interframe Space Number for AP. The range is 0 to 15. The
default is 1.
Accept Aggregation This option defines whether or not
the MAC layer will accept an ADDBA request. The default
is Yes. Select No to disable this option.
TXOP for AP This option defines the Transmission
Opportunity for AP. The range is 0 to 8192. The default is
3008.
Max. Number of Packets in Aggregation This option
defines the maximum number of packets (sub-frames) in
the aggregate. The range is 0 to 7. The default is 7.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Max. Aggregation Size This option defines the maximum
size of the aggregate (in bytes). The range is 0 to 16000.
The default is 12000.
Timeout Internal This option defines the timeout period
in which the aggregate should be closed with a “closing
condition” before it is closed by the timer. The range is 0 to
100 ms. The default is 3.
Min. Size of Packet in Aggregation This option defines
the minimum size (in bytes) of packets to be accumulated
in the aggregate. The range is 0 to 1500. The default
is 10.
ADDBA Timeout This option defines the duration
after which the ADDBA setup is terminated, if there are
no frame exchanges within this duration by the Block
Acknowledgement (ACK) agreement. The range is 0 to
65535 ms. The default is 0, which disables the timeout.
Aggregation Window Size This option defines the
maximum number of packets transmitted without getting
ACKs. The range is 0 to 64. The default is 64.
CW Min for STA This option defines the minimum
contention window limit from which the random backoff
is computed for an STA in BSS. The value is set to 7 (default)
and cannot be changed.
Voice
Use Aggregation This option defines whether or not the
Media Access Control (MAC) layer will set up an Add Block
Acknowledgement (ADDBA) session. The default is Yes.
Select No to disable this option.
Accept Aggregation This option defines whether or not
the MAC layer will accept an ADDBA request. The default
is Yes. Select No to disable this option.
Max. Number of Packets in Aggregation This option
defines the maximum number of packets (sub-frames) in
the aggregate. The range is 0 to 2. The default is 2.
Max. Aggregation Size This option defines the maximum
size of the aggregate (in bytes). The range is 0 to 16000.
The default is 10000.
Timeout Internal This option defines the timeout period
in which the aggregate should be closed with a “closing
condition” before it is closed by the timer. The range is 0 to
100 ms. The default is 10.
Min. Size of Packet in Aggregation This option defines
the minimum size (in bytes) of packets to be accumulated
in the aggregate. The range is 0 to 1500. The default
is 10.
CW Max for STA This option defines the maximum
contention window limit from which the random backoff
is computed for an STA in BSS. The value is set to 15
(default) and cannot be changed.
ADDBA Timeout This option defines the duration
after which the ADDBA setup is terminated, if there are
no frame exchanges within this duration by the Block
Acknowledgement (ACK) agreement. The range is 0 to
65535 ms. The default is 0, which disables the timeout.
AIFSN for STA This option defines the Arbitration
Interframe Space Number for an STA in BSS. The range is 0
to 15. The default is 2.
Aggregation Window Size This option defines the
maximum number of packets transmitted without getting
ACKs. The range is 0 to 64. The default is 64.
TXOP for STA This option defines the Transmission
Opportunity for an STA in BSS. The range is 0 to 8192. The
default is 3008.
CW Min for STA This option defines the minimum
contention window limit from which the random backoff
is computed for an STA in BSS. The value is set to 3 (default)
and cannot be changed.
CW Min for AP This option defines the minimum
contention window limits from which the random backoff
is computed for AP. The value is set to 7 (default) and
cannot be changed.
CW Max for AP This option defines the maximum
contention window limits from which the random backoff
Ultra RangePlus Wireless-N Access Point with Dual-Band
CW Max for STA This option defines the maximum
contention window limit from which the random backoff
is computed for an STA in BSS. The value is set to 7 (default)
and cannot be changed.
10
Advanced Configuration
Chapter 3
AIFSN for STA This option defines the Arbitration
Interframe Space Number for an STA in BSS. The range is 0
to 15. The default is 2.
will be able to communicate with the Router or Access
Point but not with each other. To use this function, select
Enabled. AP Isolation is disabled by default.
TXOP for STA This option defines the Transmission
Opportunity for an STA in BSS. The range is 0 to 8192. The
default is 1504.
Authentication Type The Authentication Type setting
is available if the Security mode is WEP. The default is
set to Auto, which allows either Open System or Shared
Key authentication to be used. With Open System
authentication, the sender and the recipient do NOT
use a WEP key for authentication. With Shared Key
authentication, the sender and recipient use a WEP key for
authentication. Select Shared Key to only use Shared Key
authentication.
CW Min for AP This option defines the minimum
contention window limits from which the random backoff
is computed for AP. The value is set to 3 (default) and
cannot be changed.
CW Max for AP This option defines the maximum
contention window limits from which the random backoff
is computed for AP. The value is set to 7 (default) and
cannot be changed.
AIFSN for AP This option defines the Arbitration
Interframe Space Number for AP. The range is 0 to 15. The
default is 1.
TXOP for AP This option defines the Transmission
Opportunity for AP. The range is 0 to 8192. The default is
1504.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Wireless > Advanced Wireless Settings
Configure the Access Point’s advanced wireless functions.
These settings should only be adjusted by an expert
administrator as incorrect settings can reduce wireless
performance.
Basic Rate The Basic Rate setting is not actually one rate
of transmission but a series of rates at which the Access
Point can transmit. The Access Point will advertise its
Basic Rate to the other wireless devices in your network,
so they know which rates will be used. The Access Point
will also advertise that it will automatically select the best
rate for transmission. The default setting is Default, when
the Access Point can transmit at all standard wireless
rates (1-2Mbps, 5.5Mbps, 11Mbps, 18Mbps, and 24Mbps).
Other options are 1-2Mbps, for use with older wireless
technology, and All, when the Access Point can transmit
at all wireless rates. The Basic Rate is not the actual rate of
data transmission. If you want to specify the Access Point’s
rate of data transmission, configure the Transmission Rate
setting.
Transmission Rate The rate of data transmission should
be set depending on the speed of your wireless network.
You can select from a range of transmission speeds, or you
can select Auto to have the Access Point automatically
use the fastest possible data rate and enable the AutoFallback feature. Auto-Fallback will negotiate the best
possible connection speed between the Access Point and
a wireless client. The default is Auto.
N Transmission Rate The rate of data transmission
should be set depending on the speed of your Wireless-N
networking. You can select from a range of transmission
speeds, or you can select Auto to have the Access Point
automatically use the fastest possible data rate and enable
the Auto-Fallback feature. Auto-Fallback will negotiate the
best possible connection speed between the Access Point
and a wireless client. The default is Auto.
Wireless > Advanced Wireless Settings
NOTE: The settings on the Advanced Wireless
Settings screen are designed for advanced users
only.
Advanced Wireless
AP Isolation This isolates all wireless clients and wireless
devices on your network from each other. Wireless devices
Ultra RangePlus Wireless-N Access Point with Dual-Band
Transmission Power This option sets the percentage
of maximal transmit power relative to the regulatory
domain restrictions. For example, if the regulatory domain
restriction allows transmissions of up to 20 dB, then setting
the percentage at 50% allows maximal transmit power of
10 dB. Select the percentage you want to use: 12%, 25%,
50%, or 100%. The default is 100%.
CTS Protection Mode The Access Point will automatically
use CTS (Clear-To-Send) Protection Mode when your
Wireless-N and Wireless-G products are experiencing
severe problems and are not able to transmit to the
11
Advanced Configuration
Chapter 3
Access Point in an environment with heavy 802.11b traffic.
This function boosts the Access Point’s ability to catch all
Wireless-N and Wireless-G transmissions but will severely
decrease performance. The default is Auto.
Access Point
Beacon Interval Enter a value between 1 and 65,535
milliseconds. The Beacon Interval value indicates the
frequency interval of the beacon. A beacon is a packet
broadcast by the Access Point to synchronize the wireless
network. The default value is 100.
Access Point Password Enter a new Password for the
Access Point.
DTIM Interval This value, between 1 and 255, indicates
the interval of the Delivery Traffic Indication Message
(DTIM). A DTIM field is a countdown field informing
clients of the next window for listening to broadcast and
multicast messages. When the Access Point has buffered
broadcast or multicast messages for associated clients, it
sends the next DTIM with a DTIM Interval value. Its clients
hear the beacons and awaken to receive the broadcast
and multicast messages. The default value is 1.
RTS Threshold Should you encounter inconsistent data
flow, only minor reduction of the default value, 2347, is
recommended. If a network packet is smaller than the
preset RTS threshold size, the RTS/CTS mechanism will not
be enabled. The Access Point sends Request to Send (RTS)
frames to a particular receiving station and negotiates
the sending of a data frame. After receiving an RTS, the
wireless station responds with a Clear to Send (CTS) frame
to acknowledge the right to begin transmission. The RTS
Threshold value should remain at its default value of
2347.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Administration > Management
Use this screen to manage specific Access Point functions:
access to the web‑based utility, backup of the configuration
file, and reboot.
Use a password to protect access to the web-based
utility.
Re-enter to confirm Enter the Password again to confirm.
Idle Timeout The login times out after a period of
inactivity that you specify. The range is 60 to 3600 seconds.
The default is 600.
Local Management Access
Access via Wireless If you are using the Access Point in
a public domain where you are giving wireless access to
your guests, you can disable wireless access to the Access
Point’s web-based utility. You will only be able to access
the web-based utility via a wired connection if you disable
the setting. Keep the default, Enabled, to allow wireless
access to the Access Point’s web-based utility, or select
Disabled to block wireless access to the utility.
Backup and Restore
Backup To back up the Access Point’s configuration file,
click Backup Configurations. Then follow the on-screen
instructions.
Restore Click Browse and select the configuration file.
Then click Restore Configurations.
System Reboot
Reboot To reboot or restart the Access Point, click Start
to Reboot.
Click Save Settings to apply your changes, or click Cancel
Changes to cancel your changes.
Administration > Factory Defaults
Use this screen to restore the Access Point’s configuration
to its factory default settings.
Factory Defaults
Restore All Settings To reset the Access Point’s settings
to the factory defaults, click Restore All Settings. Any
settings you have saved will be lost when the default
settings are restored.
Administration > Management
Administration > Factory Defaults
Ultra RangePlus Wireless-N Access Point with Dual-Band
12
Advanced Configuration
Chapter 3
Administration > Firmware Upgrade
Status > Wireless Network
Use this screen to upgrade the Access Point’s firmware.
Do not upgrade the firmware unless you are experiencing
problems with the Access Point or the new firmware has a
feature you want to use.
Information about your wireless network is displayed.
Status > Wireless Network
Administration > Firmware Upgrade
Before upgrading the firmware, download the Access Point’s
firmware upgrade file from www.linksysbycisco.com.
Firmware Upgrade
Please select a file to upgrade the firmware Click
Browse and select the firmware upgrade file. Then click
Start to Upgrade and follow the on-screen instructions.
MAC Address The Access Point’s MAC Address, as seen
on your local, wireless network, is displayed.
Mode The wireless mode used by the network is
displayed.
Network Name (SSID) The wireless network name or
SSID is displayed.
Wireless Band The radio band of your wireless network
is displayed.
Status > Access Point
Channel Width The channel width, in MHz, used by your
wireless network is displayed.
The Access Point’s current status information is displayed.
Wide Channel Depending on the channel settings of
your Access Point, the Wide Channel is displayed.
Standard Channel The Standard Channel setting is
displayed.
Security The security method of your wireless network
is displayed.
SSID Broadcast The status of SSID broadcast (enabled or
disabled) is displayed.
Status > About
Status > Access Point
Information about the web-based utility is displayed.
Access Point Information
Firmware Version The Access Point’s current firmware is
displayed.
Local Network
Local MAC Address The Access Point’s MAC Address, as
seen on your local, Ethernet network, is displayed.
Status > About
Access Point IP Address The Access Point’s IP Address, as
seen on your local, Ethernet network, is displayed.
Web Server
Subnet Mask The Subnet Mask configured for your local
network is displayed.
Powered By The web server of the web-based utility is
displayed.
Ultra RangePlus Wireless-N Access Point with Dual-Band
13
Appendix A
Appendix A:
Troubleshooting
Troubleshooting
to its factory default, admin. All other Access Point
settings will be reset to the factory defaults as well.
(To access the web-based utility, enter admin in the
Password field.)
Your computer or other wired, Ethernet device cannot
communicate with the wireless router.
After you make changes through the web-based utility,
the new settings are not displayed on-screen.
1. Access the web-based utility of the Access Point (refer
to Chapter 3: Advanced Configuration, page 3).
On your web browser, click Refresh. If the new settings
are not displayed, then follow these instructions:
2. On the Basic Wireless Settings screen, make sure the
Network Name (SSID) matches the name of your
wireless network.
1. Unplug the power adapter from the Access Point.
3. Make sure the security settings (WPA, WPA2, or WEP)
match the security settings of your wireless network.
3. On your web browser, click Refresh.
The Access Point’s IP address needs to be changed.
If the Access Point is connected to a network with a DHCP
server (usually the network router), then the Access Point
will obtain its IP address from the DHCP server.
2. Wait five seconds, and then plug the power adapter
back into the Access Point.
WEB: If your questions are not addressed
here, refer to the Linksys website,
www.linksysbycisco.com
If you want the Access Point to always use a static IP
address, then follow these instructions:
1. Access the web-based utility of the Access Point (refer
to Chapter 3: Advanced Configuration, page 3).
2. Click the Network Setup tab.
3. From the Network Connection Type drop-down menu,
select Static IP.
4. Complete the Static IP Address, Subnet Mask, and
Default Gateway fields.
5. Click Save Settings.
The Access Point-enabled computer or other wired,
Ethernet device will not communicate with another
wireless-enabled device (such as a computer or printer).
Check the following:
•• Make sure the wireless-enabled device is on the same
wireless network as the computer or other wired,
Ethernet device connected to the Access Point.
•• Make sure that the same Network Name (SSID) is used
for all devices on the wireless network.
•• Make sure all devices are on the same IP network,
using compatible IP addresses.
The web-based utility does not accept your password.
Check the following:
•• The password is case-sensitive. Make sure that you are
using the correct case(s) when entering the password.
•• If you forget your password, you can reset the Access
Point to its factory defaults.
Press and hold the Access Point’s Reset button for
approximately five seconds; the password will be reset
Ultra RangePlus Wireless-N Access Point with Dual-Band
14
Specifications
Appendix B
Appendix B:
Specifications
Model
WAP610N
Standards
IEEE 802.3u, 802.11g, 802.11b,
802.11a, Draft 802.11n
LEDs
Power, Ethernet, Wi-Fi Protected
Setup™, Wireless
Ports
Ethernet, Power
Buttons
Reset, Wi-Fi Protected Setup™
Cabling Type
CAT5
No. of Antennas
3 (internal)
(145 x 106 x 52 mm)
Weight
5.61 oz (159 g)
Power
12V, 1A
Certi-cation
FCC, UL/cUL, ICES-003, RSS210,
Wi-Fi (IEEE 802.11a/b/g/draft n),
WPA2™, Wi-Fi Protected Setup™
Operating Temp.
32 to 104ºF (0 to 40ºC)
Storage Temp.
-4 to 140ºF (-20 to 60ºC)
Operating Humidity 10 to 85% Noncondensing
Storage Humidity
5 to 90% Noncondensing
Speci-cations are subject to change without notice.
Antenna Connector
Type
N/A
Detachable (Yes/No) No
Modulations
802.11a: OFDM/BPSK, QPSK,
16-QAM, 64-QAM
802.11b: CCK/QPSK, BPSK
802.11g: OFDM/BPSK, QPSK,
16-QAM, 64-QAM
802.11n: OFDM/BPSK, QPSK,
Antenna Gain in dBi For 2.4 GHz: 1.58 dBi
For 5 GHz: 1.45 dBi
Wireless Security
WEP, Wi-Fi Protected Access™2
(WPA2)
Security Key Bits
Up to 128-Bit Encryption
OS Requirements
Windows XP, Vista, or Vista 64-Bit
Edition with Latest Updates (for
Setup Wizard only)
Environmental
Dimensions
5.71" x 4.17" x 2.05"
Ultra RangePlus Wireless-N Access Point with Dual-Band
15
Appendix C
Appendix C:
Warranty Information
Limited Warranty
Linksys warrants this Linksys hardware product against
defects in materials and workmanship under normal
use for the Warranty Period, which begins on the date of
purchase by the original end-user purchaser and lasts for
the period specified below:
•• One (1) year for new product
•• Ninety (90) days for refurbished product
Your exclusive remedy and Linksys’ entire liability under
this limited warranty will be for Linksys, at its option, to
(a) repair the product with new or refurbished parts,
(b) replace the product with a reasonably available
equivalent new or refurbished Linksys product, or (c) refund
the purchase price of the product less any rebates. Any
repaired or replacement products will be warranted for
the remainder of the original Warranty Period or thirty (30)
days, whichever is longer. All products and parts that are
replaced become the property of Linksys.
Linksys additionally warrants that any media on which
the software may be provided will be free from defects in
materials and workmanship under normal use for a period
of ninety (90) days from the date of original purchase.
Your exclusive remedy and Linksys’ entire liability under
this limited warranty will be for Linksys, at its option, to
(a) replace the software media, or (b) refund the purchase
price of the software media.
Exclusions and Limitations
This limited warranty does not apply if: (a) the product
assembly seal has been removed or damaged, (b) the
product has been altered or modified, except by Linksys,
(c) the product damage was caused by use with nonLinksys products, (d) the product has not been installed,
operated, repaired, or maintained in accordance with
instructions supplied by Linksys, (e) the product has
been subjected to abnormal physical or electrical stress,
misuse, negligence, or accident, (f ) the serial number on
the Product has been altered, defaced, or removed, or
(g) the product is supplied or licensed for beta, evaluation,
testing or demonstration purposes for which Linksys does
not charge a purchase price or license fee.
EXCEPT FOR THE LIMITED WARRANTY ON MEDIA SET FORTH
ABOVE AND TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, ALL SOFTWARE PROVIDED BY LINKSYS
WITH THE PRODUCT, WHETHER FACTORY LOADED ON THE
PRODUCT OR CONTAINED ON MEDIA ACCOMPANYING
THE PRODUCT, IS PROVIDED “AS IS” WITHOUT WARRANTY
OF ANY KIND. Without limiting the foregoing, Linksys does
Ultra RangePlus Wireless-N Access Point with Dual-Band
Warranty Information
not warrant that the operation of the product or software
will be uninterrupted or error free. Also, due to the
continual development of new techniques for intruding
upon and attacking networks, Linksys does not warrant
that the product, software or any equipment, system or
network on which the product or software is used will be
free of vulnerability to intrusion or attack. The product
may include or be bundled with third party software or
service offerings. This limited warranty shall not apply to
such third party software or service offerings. This limited
warranty does not guarantee any continued availability
of a third party’s service for which this product’s use or
operation may require.
TO THE EXTENT NOT PROHIBITED BY APPLICABLE
LAW, ALL IMPLIED WARRANTIES AND CONDITIONS
OF MERCHANTABILITY, SATISFACTORY QUALITY OR
FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO
THE DURATION OF THE WARRANTY PERIOD. ALL OTHER
EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS
AND WARRANTIES ARE DISCLAIMED. Some jurisdictions
do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. This
limited warranty gives you specific legal rights, and you
may also have other rights which vary by jurisdiction.
TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW,
IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST
DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT,
CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES,
REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING
NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE
OF OR INABILITY TO USE THE PRODUCT, SOFTWARE OR
ANY SERVICES PROVIDED IN RESPECT OF SUCH PRODUCT
OR SOFTWARE, EVEN IF LINKSYS HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. TO THE EXTENT
NOT PROHIBITED BY APPLICABLE LAW, IN NO EVENT WILL
LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU
FOR THE PRODUCT. The foregoing limitations will apply
even if any warranty or remedy provided under this limited
warranty fails of its essential purpose. Some jurisdictions
do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or
exclusion may not apply to you.
Obtaining Warranty Service
If you have a question about your product
or experience a problem with it, please go to
www.linksysbycisco.com/support where you will find a
variety of online support tools and information to assist
you with your product. If the product proves defective
during the Warranty Period, contact Linksys Technical
Support for instructions on how to obtain warranty service.
The telephone number for Linksys Technical Support in
your area can be found in the product User Guide and
at www.linksysbycisco.com. Have your product serial
number and proof of purchase on hand when calling. A
16
Appendix C
Warranty Information
DATED PROOF OF ORIGINAL PURCHASE IS REQUIRED TO
PROCESS WARRANTY CLAIMS. If you are requested to
return your product, you will be given a Return Materials
Authorization (RMA) number. You are responsible for
properly packaging and shipping your product to Linksys
at your cost and risk. You must include the RMA number
and a copy of your dated proof of original purchase when
returning your product. Products received without a RMA
number and dated proof of original purchase will be
rejected. Do not include any other items with the product
you are returning to Linksys. Defective product covered
by this limited warranty will be repaired or replaced and
returned to you without charge. Customers outside of
the United States of America and Canada are responsible
for all shipping and handling charges, custom duties,
VAT and other associated taxes and charges. Repairs or
replacements not covered under this limited warranty will
be subject to charge at Linksys’ then-current rates.
Technical Support
This limited warranty is neither a service nor a
support contract. Information about Linksys’ current
technical support offerings and policies (including
any fees for support services) can be found at
www.linksysbycisco.com/support.
This limited warranty is governed by the laws of the
jurisdiction in which the Product was purchased by you.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,
CA 92623.
Ultra RangePlus Wireless-N Access Point with Dual-Band
17
Appendix D
Regulatory Information
Appendix D:
Regulatory Information
The availability of some specific channels and/or
operational frequency bands is country dependent
and programmed at the factory to match the intended
destination. This setting is not accessible by the end user.
FCC Statement
Safety Notices
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This product has been tested and complies with the
specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used according to the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which is found by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment or
devices
•
Connect the equipment to an outlet other than the
receiver’s
•
Consult a dealer or an experienced radio/TV technician
for assistance
WARNING: Do not use this product near water,
for example, in a wet basement or near a
swimming pool.
WARNING: Avoid using this product diring an
electrical storm. There ma be a remote risk of
electric shock from lightning.
WARNING: This product contains lead, known
to the State of California to cause cancer, and
birth defects or other reproductive harm. Wash
hands after handling.
FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
For operation within the 5.15 ~ 5.25GHz frequency range,
it is restricted to indoor environments.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Ultr a R angePlus Wireless-N A ccess P oint with D ual-B and
18
Appendix D
Regulatory Information
section ne doivent pas être capables de transmettre dans
la bande 5 600-5 650 MHz afin de protéger les radars
d’Environnement Canada qui l’utilisent.
Wireless Disclaimer
The maximum performance for wireless is derived from
IEEE Standard 802.11 specifications. Actual performance
can vary, including lower wireless network capacity,
data throughput rate, range and coverage. Performance
depends on many factors, conditions and variables,
including distance from the access point, volume of
network traffic, building materials and construction,
operating system used, mix of wireless products used,
interference and other adverse conditions.
Avis de non-responsabilité concernant les
appareils sans fil
Les performances maximales pour les réseaux sans fil
sont tirées des spécifications de la norme IEEE 802.11.
Les performances réelles peuvent varier, notamment
en fonction de la capacité du réseau sans fil, du débit
de la transmission de données, de la portée et de la
couverture. Les performances dépendent de facteurs,
conditions et variables multiples, en particulier de la
distance par rapport au point d’accès, du volume du trafic
réseau, des matériaux utilisés dans le bâtiment et du
type de construction, du système d’exploitation et de la
combinaison de produits sans fil utilisés, des interférences
et de toute autre condition défavorable.
Ultra RangePlus Wireless-N Access Point with Dual-Band
20
Appendix D
User Information for Consumer Products
Covered by EU Directive 2002/96/EC on
Waste Electric and Electronic Equipment
(WEEE)
This document contains important information for users
with regards to the proper disposal and recycling of
Linksys products. Consumers are required to comply
with this notice for all electronic products bearing the
following symbol:
Regulatory Information
Čeština (Czech) - Informace o ochraně životního
prostředí pro zákazníky v zemích Evropské unie
Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené
tímto symbolem na produktu anebo na obalu bylo likvidováno
s netříděným komunálním odpadem. Tento symbol udává,
že daný produkt musí být likvidován odděleně od běžného
komunálního odpadu. Odpovídáte za likvidaci tohoto produktu
a dalších elektrických a elektronických zařízení prostřednictvím
určených sběrných míst stanovených vládou nebo místními
úřady. Správná likvidace a recyklace pomáhá předcházet
potenciálním negativním dopadům na životní prostředí a lidské
zdraví. Podrobnější informace o likvidaci starého vybavení si
laskavě vyžádejte od místních úřadů, podniku zabývajícího se
likvidací komunálních odpadů nebo obchodu, kde jste produkt
zakoupili.
Dansk (Danish) - Miljøinformation for kunder i EU
English - Environmental Information for Customers in
the European Union
European Directive 2002/96/EC requires that the equipment
bearing this symbol on the product and/or its packaging must
not be disposed of with unsorted municipal waste. The symbol
indicates that this product should be disposed of separately
from regular household waste streams. It is your responsibility to
dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or
local authorities. Correct disposal and recycling will help prevent
potential negative consequences to the environment and
human health. For more detailed information about the disposal
of your old equipment, please contact your local authorities,
waste disposal service, or the shop where you purchased the
product.
Български (Bulgarian) - Информация относно
опазването на околната среда за потребители в
Европейския съюз
Европейска директива 2002/96/EC изисква уредите, носещи
този символ върху изделието и/или опаковката му, да не
се изхвърля т с несортирани битови отпадъци. Символът
обозначава, че изделието трябва да се изхвърля отделно от
сметосъбирането на обикновените битови отпадъци. Ваша
е отговорността този и другите електрически и електронни
уреди да се изхвърлят в предварително определени от
държавните или общински органи специализирани пунктове
за събиране. Правилното изхвърляне и рециклиране
ще спомогнат да се предотвратят евентуални вредни за
околната среда и здравето на населението последствия. За
по-подробна информация относно изхвърлянето на вашите
стари уреди се обърнете към местните власти, службите за
сметосъбиране или магазина, от който сте закупили уреда.
Ultra RangePlus Wireless-N Access Point with Dual-Band
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol
på produktet og/eller emballagen ikke må bortskaffes som
usorteret kommunalt affald. Symbolet betyder, at dette produkt
skal bortskaffes adskilt fra det almindelige husholdningsaffald.
Det er dit ansvar at bortskaffe dette og andet elektrisk og
elektronisk udstyr via bestemte indsamlingssteder udpeget
af staten eller de lokale myndigheder. Korrekt bortskaffelse
og genvinding vil hjælpe med til at undgå mulige skader for
miljøet og menneskers sundhed. Kontakt venligst de lokale
myndigheder, renovationstjenesten eller den butik, hvor du
har købt produktet, angående mere detaljeret information om
bortskaffelse af dit gamle udstyr.
Deutsch (German) - Umweltinformation für Kunden
innerhalb der Europäischen Union
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische
Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit
diesem Symbol versehen ist , nicht zusammen mit unsortiertem
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf
hin, dass das Produkt von regulärem Haushaltmüll getrennt
entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses
Gerät und andere elektrische und elektronische Geräte über
die dafür zuständigen und von der Regierung oder örtlichen
Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei,
potentielle negative Folgen für Umwelt und die menschliche
Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur
Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an
die örtlichen Behörden oder städtischen Entsorgungsdienste
oder an den Händler, bei dem Sie das Produkt erworben haben.
21
Appendix D
Regulatory Information
Eesti (Estonian) - Keskkonnaalane informatsioon
Euroopa Liidus asuvatele klientidele
Français (French) - Informations environnementales
pour les clients de l’Union européenne
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on
seadmeid, millel on tootel või pakendil käesolev sümbol ,
keelatud kõrvaldada koos sorteerimata olmejäätmetega. See
sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest
olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva
ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike
ametiasutuste poolt ette nähtud kogumispunktide kaudu.
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste
tervisele. Vanade seadmete kõrvaldamise kohta täpsema
informatsiooni saamiseks võtke palun ühendust kohalike
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te
toote ostsite.
La directive européenne 2002/96/CE exige que l’équipement
sur lequel est apposé ce symbole sur le produit et/ou son
emballage ne soit pas jeté avec les autres ordures ménagères. Ce
symbole indique que le produit doit être éliminé dans un circuit
distinct de celui pour les déchets des ménages. Il est de votre
responsabilité de jeter ce matériel ainsi que tout autre matériel
électrique ou électronique par les moyens de collecte indiqués
par le gouvernement et les pouvoirs publics des collectivités
territoriales. L’élimination et le recyclage en bonne et due forme
ont pour but de lutter contre l’impact néfaste potentiel de ce
type de produits sur l’environnement et la santé publique. Pour
plus d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs publics
locaux, le service de traitement des déchets, ou l’endroit où vous
avez acheté le produit.
Español (Spanish) - Información medioambiental para
clientes de la Unión Europea
La Directiva 2002/96/CE de la UE exige que los equipos que
lleven este símbolo en el propio aparato y/o en su embalaje
no deben eliminarse junto con otros residuos urbanos no
seleccionados. El símbolo indica que el producto en cuestión
debe separarse de los residuos domésticos convencionales con
vistas a su eliminación. Es responsabilidad suya desechar este y
cualesquiera otros aparatos eléctricos y electrónicos a través de
los puntos de recogida que ponen a su disposición el gobierno y
las autoridades locales. Al desechar y reciclar correctamente estos
aparatos estará contribuyendo a evitar posibles consecuencias
negativas para el medio ambiente y la salud de las personas. Si
desea obtener información más detallada sobre la eliminación
segura de su aparato usado, consulte a las autoridades locales,
al servicio de recogida y eliminación de residuos de su zona o
pregunte en la tienda donde adquirió el producto.
Ελληνικά (Greek) - Στοιχεία περιβαλλοντικής
προστασίας για πελάτες εντός της Ευρωπαϊκής
Ένωσης
Σύμφωνα με την Κοινοτική Οδηγία 2002/96/EC, ο εξοπλισμός που
φέρει αυτό το σύμβολο στο προϊόν ή/και τη συσκευασία του
δεν πρέπει να απορρίπτεται μαζί με τα μη διαχωρισμένα αστικά
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων,
οι οποίες ορίζονται από το κράτος ή τις αρμόδιες τοπικές αρχές.
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη
ενδεχόμενων αρνητικών επιπτώσεων στο περιβάλλον και την
υγεία. Για περισσότερες πληροφορίες σχετικά με την απόρριψη
του παλαιού σας εξοπλισμού, επικοινωνήστε με τις τοπικές αρχές,
τις υπηρεσίες αποκομιδής απορριμμάτων ή το κατάστημα από
το οποίο αγοράσατε το προϊόν.
Ultra RangePlus Wireless-N Access Point with Dual-Band
Italiano (Italian) - Informazioni relative all’ambiente
per i clienti residenti nell’Unione Europea
La direttiva europea 2002/96/EC richiede che le apparecchiature
contrassegnate con questo simbolo
sul prodotto e/o
sull’imballaggio non siano smaltite insieme ai rifiuti urbani
non differenziati. Il simbolo indica che questo prodotto non
deve essere smaltito insieme ai normali rifiuti domestici. È
responsabilità del proprietario smaltire sia questi prodotti sia
le altre apparecchiature elettriche ed elettroniche mediante
le specifiche strutture di raccolta indicate dal governo o dagli
enti pubblici locali. Il corretto smaltimento ed il riciclaggio
aiuteranno a prevenire conseguenze potenzialmente negative
per l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle vecchie
apparecchiature in Vostro possesso, Vi invitiamo a contattare gli
enti pubblici di competenza, il servizio di smaltimento rifiuti o il
negozio nel quale avete acquistato il prodotto.
Latviešu valoda (Latvian) - Ekoloģiska informācija
klientiem Eiropas Savienības jurisdikcijā
Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota
zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst
izmest nešķirotā veidā kopā ar komunālajiem atkritumiem
(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē
to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar
parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo
un citas elektriskas un elektroniskas ierīces izmest atkritumos,
izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko
nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos
un pārstrāde tiek veikta pareizi, tad mazinās iespējamais
kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par
novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt
vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā,
kur iegādājāties šo izstrādājumu.
22
Appendix D
Regulatory Information
Lietuvškai (Lithuanian) - Aplinkosaugos informacija,
skirta Europos Sąjungos vartotojams
Nederlands (Dutch) - Milieu-informatie voor klanten
in de Europese Unie
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir
kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį),
negalima šalinti kartu su nerūšiuotomis komunalinėmis
atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai
nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam
tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo
sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta
galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos
apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios
institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose
įsigijote tą gaminį.
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die
is voorzien van dit symbool op het product of de verpakking,
niet mag worden ingezameld met niet-gescheiden huishoudelijk
afval. Dit symbool geeft aan dat het product apart moet worden
ingezameld. U bent zelf verantwoordelijk voor de vernietiging
van deze en andere elektrische en elektronische apparatuur via de
daarvoor door de landelijke of plaatselijke overheid aangewezen
inzamelingskanalen. De juiste vernietiging en recycling van
deze apparatuur voorkomt mogelijke negatieve gevolgen voor
het milieu en de gezondheid. Voor meer informatie over het
vernietigen van uw oude apparatuur neemt u contact op met
de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de
winkel waar u het product hebt aangeschaft.
Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti
fl-Unjoni Ewropea
Norsk (Norwegian) - Miljøinformasjon for kunder i EU
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih
is-simbolu
fuq il-prodott u/jew fuq l-ippakkjar ma jistax
jintrema ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu
jindika li dan il-prodott għandu jintrema separatament minn ma’
l-iskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi
dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku
permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew
mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin
jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u
għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata
dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja
lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew
il-ħanut minn fejn xtrajt il-prodott.
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol
avbildet på produktet og/eller pakningen, ikke må kastes
sammen med usortert avfall. Symbolet indikerer at dette
produktet skal håndteres atskilt fra ordinær avfallsinnsamling
for husholdningsavfall. Det er ditt ansvar å kvitte deg med
dette produktet og annet elektrisk og elektronisk avfall via egne
innsamlingsordninger slik myndighetene eller kommunene
bestemmer. Korrekt avfallshåndtering og gjenvinning vil
være med på å forhindre mulige negative konsekvenser for
miljø og helse. For nærmere informasjon om håndtering av
det kasserte utstyret ditt, kan du ta kontakt med kommunen,
en innsamlingsstasjon for avfall eller butikken der du kjøpte
produktet.
Magyar (Hungarian) - Környezetvédelmi információ az
európai uniós vásárlók számára
Polski (Polish) - Informacja dla klientów w Unii
Europejskiej o przepisach dotyczących ochrony
środowiska
A 2002/96/EC számú európai uniós irányelv megkívánja, hogy
azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán
az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági
hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott
termék kidobásakor a szokványos háztartási hulladékelszállítási
rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön
felelõssége, hogy ezt, és más elektromos és elektronikus
berendezéseit a kormányzati vagy a helyi hatóságok által
kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ
hulladékfeldolgozás segít a környezetre és az emberi egészségre
potenciálisan ártalmas negatív hatások megelõzésében. Ha
elavult berendezéseinek felszámolásához további részletes
információra van szüksége, kérjük, lépjen kapcsolatba a helyi
hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal
üzlettel, ahol a terméket vásárolta.
Ultra RangePlus Wireless-N Access Point with Dual-Band
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt
oznaczony symbolem znajdującym się na produkcie i/lub jego
opakowaniu nie był wyrzucany razem z innymi niesortowanymi
odpadami komunalnymi. Symbol ten wskazuje, że produkt
nie powinien być usuwany razem ze zwykłymi odpadami z
gospodarstw domowych. Na Państwu spoczywa obowiązek
wyrzucania tego i innych urządzeń elektrycznych oraz
elektronicznych w punktach odbioru wyznaczonych przez władze
krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób
i jego recykling pomogą zapobiec potencjalnie negatywnym
konsekwencjom dla środowiska i zdrowia ludzkiego. W celu
uzyskania szczegółowych informacji o usuwaniu starego sprzętu,
prosimy zwrócić się do lokalnych władz, służb oczyszczania
miasta lub sklepu, w którym produkt został nabyty.
23
Appendix D
Regulatory Information
Português (Portuguese) - Informação ambiental para
clientes da União Europeia
Slovenščina (Slovene) - Okoljske informacije za
stranke v Evropski uniji
A Directiva Europeia 2002/96/CE exige que o equipamento
que exibe este símbolo no produto e/ou na sua embalagem
não seja eliminado junto com os resíduos municipais não
separados. O símbolo indica que este produto deve ser
eliminado separadamente dos resíduos domésticos regulares.
É da sua responsabilidade eliminar este e qualquer outro
equipamento eléctrico e electrónico através das instalações
de recolha designadas pelas autoridades governamentais ou
locais. A eliminação e reciclagem correctas ajudarão a prevenir
as consequências negativas para o ambiente e para a saúde
humana. Para obter informações mais detalhadas sobre a
forma de eliminar o seu equipamento antigo, contacte as
autoridades locais, os serviços de eliminação de resíduos ou o
estabelecimento comercial onde adquiriu o produto.
Evropska direktiva 2002/96/ES prepoveduje odlaganje opreme s
tem simbolom – na izdelku in/ali na embalaži z nesortiranimi
komunalnimi odpadki. Ta simbol opozarja, da je treba izdelek
zavreči ločeno od preostalih gospodinjskih odpadkov. Vaša
odgovornost je, da to in preostalo električno in elektronsko
opremo oddate na posebna zbirališča, ki jih določijo državne
ustanove ali lokalne oblasti. S pravilnim odlaganjem in
recikliranjem boste preprečili morebitne škodljive vplive na
okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare
opreme, se obrnite na lokalne oblasti, odlagališče odpadkov ali
trgovino, kjer ste izdelek kupili.
Română (Romanian) - Informaţii de mediu pentru
clienţii din Uniunea Europeană
Directiva europeană 2002/96/CE impune ca echipamentele care
prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să
nu fie casate împreună cu gunoiul menajer municipal. Simbolul
indică faptul că acest produs trebuie să fie casat separat de
gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi
acest produs şi alte echipamente electrice şi electronice prin
intermediul unităţilor de colectare special desemnate de guvern
sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta
la prevenirea potenţialelor consecinţe negative asupra sănătăţii
mediului şi a oamenilor. Pentru mai multe informaţii detaliate
cu privire la casarea acestui echipament vechi, contactaţi
autorităţile locale, serviciul de salubrizare sau magazinul de la
care aţi achiziţionat produsul.
Slovenčina (Slovak) - Informácie o ochrane životného
prostredia pre zákazníkov v Európskej únii
Podľa európskej smernice 2002/96/ES zariadenie s týmto
symbolom
na produkte a/alebo jeho balení nesmie byť
likvidované spolu s netriedeným komunálnym odpadom.
Symbol znamená, že produkt by sa mal likvidovať oddelene
od bežného odpadu z domácností. Je vašou povinnosťou
likvidovať toto i ostatné elektrické a elektronické zariadenia
prostredníctvom špecializovaných zberných zariadení určených
vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia
pomôže zabrániť prípadným negatívnym dopadom na životné
prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie
informácie o likvidácii starého zariadenia, obráťte sa, prosím, na
miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov
alebo obchod, v ktorom ste si produkt zakúpili.
Ultra RangePlus Wireless-N Access Point with Dual-Band
Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä
symboli
itse tuotteessa ja/tai sen pakkauksessa, laitteistoa
ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.
Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään
tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää
tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet
viemällä tuote tai tuotteet viranomaisten määräämään
keräyspisteeseen. Laitteiston oikea hävittäminen estää
mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten
terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta
saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä
myymälästä, josta ostit tuotteen.
Svenska (Swedish) - Miljöinformation för kunder i
Europeiska unionen
Det europeiska direktivet 2002/96/EC kräver att utrustning med
denna symbol på produkten och/eller förpackningen inte får
kastas med osorterat kommunalt avfall. Symbolen visar att denna
produkt bör kastas efter att den avskiljts från vanligt hushållsavfall.
Det faller på ditt ansvar att kasta denna och annan elektrisk och
elektronisk utrustning på fastställda insamlingsplatser utsedda
av regeringen eller lokala myndigheter. Korrekt kassering och
återvinning skyddar mot eventuella negativa konsekvenser
för miljön och personhälsa. För mer detaljerad information om
kassering av din gamla utrustning kontaktar du dina lokala
myndigheter, avfallshanteringen eller butiken där du köpte
produkten.
WEB: For additional information, please visit
www.linksysbycisco.com
24
Appendix E
Appendix E: Software End
User License Agreement
Cisco Products
This product from Cisco Systems, Inc. or its subsidiary
licensing the Software instead of Cisco Systems, Inc.
(“Cisco”) contains software (including firmware) originating
from Cisco and its suppliers and may also contain software
from the open source community.
Any software originating from Cisco and its suppliers is
licensed under the Cisco Software License Agreement
contained at Schedule 1 below. You may also be prompted
to review and accept the Cisco Software License Agreement
upon installation of the software. Separate terms and
features of Network Magic, a Cisco Software product, are
set forth in Schedule 2 below.
Any software from the open source community is licensed
under the specific license terms applicable to that software
made available by Cisco at www.linksysbycisco.com/gpl
or as provided for in Schedule 3 below. By using the Software,
you acknowledge that you have reviewed such license
terms and that you agree to be bound by the terms of
such licenses. Where such specific license terms entitle
you to the source code of such software, that source
code is available upon request at cost from Cisco for
at least three years from the purchase date of this
product and may also be available for download from
www.linksysbycisco.com/gpl. For detailed license terms
and additional information on open source software in
Cisco products please look at the Cisco public web site at:
www.linksysbycisco.com/gpl/ or Schedule 3 below as
applicable. If you would like a copy of the GPL or certain
other open source code in this Software on a CD, Cisco will
mail to you a CD with such code for $9.99 plus the cost of
shipping, upon request.
THIS SOFTWARE END USER LICENSE AGREEMENT IS
A LEGAL AGREEMENT BETWEEN YOU AND CISCO.
READ IT CAREFULLY BEFORE INSTALLING AND USING
THE SOFTWARE. IT PROVIDES A LICENSE TO USE THE
SOFTWARE AND CONTAINS WARRANTY INFORMATION
AND LIABILITY DISCLAIMERS. BY CHECKING THE “NEXT”
BOX, DOWNLOADING, INSTALLING OR USING THE
SOFTWARE, OR USING THE PRODUCT CONTAINING THE
SOFTWARE, YOU ARE CONFIRMING YOUR ACCEPTANCE
OF THE SOFTWARE AND CONSENTING TO BE BOUND
BY THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL
OF THESE TERMS, THEN DO NOT CLICK ON THE “NEXT”
BUTTON AND DO NOT DOWNLOAD, INSTALL OR USE THE
SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR,
IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER
PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND
UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO
Ultra RangePlus Wireless-N Access Point with Dual-Band
Software End User License Agreement
THE RETURN PROCESS AND POLICIES OF THE PARTY FROM
WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.
IN THE EVENT THAT YOU HAVE ELECTED TO OBTAIN A
SUBSCRIPTION LICENSE, AS INDICATED IN YOUR ORDER,
YOU ADDITIONALLY AGREE TO BE BOUND BY THE “TERMS
OF SERVICE” SET FORTH IN SCHEDULE 2 IF APPLICABLE.
Software Licenses
The software licenses applicable to software
from Cisco are made available at the Cisco public
web
site
at:
www.linksysbycisco.com
and
www.linksysbycisco.com/gpl/ respectively. For your
convenience of reference, a copy of the Cisco Software
License Agreement and the main open source code
licenses used by Cisco in its products are contained in the
Schedules below.
Schedule 1
Cisco Software License Agreement
License. Subject to the terms and conditions of this
Agreement, Cisco grants the original end user purchaser of
the Software a nonexclusive license to (i) use the Software
solely as embedded in, as a stand-alone application or
(where authorized in the applicable documentation) for
communication with such product, each solely at Cisco’s
discretion; (ii) if the Software is purchased separately
from any Cisco Product, install the Software on personal
computers within a single household or business
location according to the maximum number of licenses
you have purchased; and (iii) make one copy of the
Software in machine-readable form and one copy of the
Documentation, solely for backup purposes. This license
may not be sublicensed, and is not transferable except
to a person or entity to which you transfer ownership of
the complete Cisco product containing the Software or
complete Software product, provided you permanently
transfer all rights under this Agreement and do not retain
any full or partial copies of the Software, and the recipient
agrees to the terms of this Agreement.
“Software” includes, and this Agreement will apply to (a)
the software of Cisco or its suppliers purchased separately
or provided in or with the applicable Cisco product, and
(b) any upgrades, updates, bug fixes or modified versions
(“Upgrades”) or backup copies of the Software supplied
to you by Cisco or an authorized reseller (whether or not
for a fee), provided you already hold a valid license to the
original software and have paid any applicable fee for the
Upgrade.
“Documentation” means all documentation and other
related materials supplied by Cisco to you pursuant to this
Agreement.
25
Appendix E
License Restrictions. Other than as set forth in this
Agreement, you may not (i) make or distribute copies
of the Software or its related Documentation, or
electronically transfer the Software or Documentation
from one computer to another or over a network; (ii) alter,
merge, modify, adapt, decrypt or translate the Software or
related Documentation, or decompile, reverse engineer,
disassemble, or otherwise reduce the Software to a
human-perceivable form (except to the extent expressly
permitted by law notwithstanding this provision); (iii)
share, sell, rent, lease, or sublicense the Software or
related Documentation; (iv) modify the Software or create
derivative works based upon the Software; (v) if you
make a backup copy of the Software and Documentation,
you must reproduce all copyright notices and any other
proprietary legends found on the original Software and
Documentation; (vi) use the Software for management
of a business network with more than 8 computers; (vii)
use the Software under any circumstances for competitive
evaluation, including developing competing software;
(ix) to the extent permitted under applicable law, assign,
sublicense or otherwise transfer the Software unless
the prospective assignee, sublicensee or transferee
expressly agrees to all the terms and conditions under this
Agreement.
The Software and Documentation contain trade secrets
and/or copyrighted materials of Cisco or its suppliers. You
will not disclose or make available such trade secrets or
copyrighted material in any form to any third party.
In the event that you fail to comply with this Agreement,
the license granted to you will automatically terminate,
at which time you must immediately (i) stop using the
Cisco Product in which the Software is embedded, or
(ii) uninstall the Software and destroy all copies of the
Software and Documentation where the Software is
purchased separately. All other rights of both parties and
all other provisions of this Agreement will survive this
termination.
Ownership. The Software and Documentation are
licensed and not sold to you by Cisco and the relevant
third parties set forth in Schedule 3. Cisco and its licensors
retain all right, title and interest, including all copyright
and intellectual property rights, in and to, the Software
and Documentation and all copies and portions thereof.
All rights not specifically granted to you in this Agreement
are reserved by Cisco and its licensors. Your use of any
software product from an entity other than Cisco that may
have been recommended by Cisco is governed by such
software product’s end user license agreement.
Third Party Services, Links and Advertising. Cisco may
provide from within the Software links to websites or
third party software products. In addition, third party
services may be provided with the Software which may be
subject to terms and conditions from the provider of the
service. Cisco makes no representations as to the quality,
Ultra RangePlus Wireless-N Access Point with Dual-Band
Software End User License Agreement
suitability, functionality, or legality of any sites or products
to which links may be provided or third party services, and
you hereby waive any claim you might have against Cisco
with respect to such sites or third party software products
or services. Your correspondence or business dealings
with, or participation in promotions of third parties found
through the Software and any other terms, conditions,
warranties, or representations associated with such
dealings, are solely between you and such third party. You
agree that Cisco is not responsible or liable for any loss
or damage of any sort incurred as the result of any such
dealings or as the result of the presence of such third party
links, products or services in the Cisco Software, and Cisco
may discontinue or modify the services or links offered at
any time.
Collection and Processing of Information. You agree
that Cisco and/or its affiliates may, from time to time,
collect and process information about your Cisco product
and/or the Software and/or your use of either in order
(i) to enable Cisco to offer you Upgrades; (ii) to provide
support and assistance with your product and/or the
Software; (iii) to ensure that your Cisco product and/or
the Software is being used in accordance with the terms
of this Agreement; (iv) to provide improvements to the
way Cisco delivers technology to you and to other Cisco
customers; (v) to provide reports regarding the status
and health of the network, including network traffic and
application usage; (vi) to enable Cisco to comply with
the terms of any agreements it has with any third parties
regarding your Cisco product and/or Software; and/or
(vii) to enable Cisco to comply with all applicable laws
and/or regulations, or the requirements of any regulatory
authority or government agency. Cisco and/ or its affiliates
may collect and process this information provided that it
does not identify you personally. You agree that Cisco has
no responsibility or liability for the deletion of or failure to
store any data or other information related to your Cisco
product, Software or related Services.
The reports feature of certain Software allows you to
monitor the activity of computers running the Software in
your home or small office. You must activate this feature in
order to receive reports. If you activate the reports feature,
you agree to the following: (a) the Software tracks and
monitors the following components and activities in your
home or office: network traffic (e.g. megabytes per hour),
application usage (the foreground window is tracked and
the time each application is in the foreground during
active usage of the computer) and internet history. (b)
For all computers on which reports feature is enabled, the
above information is transmitted to servers at Cisco and/
or a third party at periodic intervals while the computer
is online. This information is associated and stored with
the email address supplied by you when you activated
the reports feature. This information is summarized into
a formal report and is emailed to the identified email
address. © Any computer on the network running the
26
Appendix E
Software can enable any other computer (on the same
primary network) to generate reports. When a computer
is enabled, that computer shows a notification that it is
being monitored. As long as that computer is enabled,
each time the Software is started the user of that particular
computer will see a notification that it is being monitored
by the reports feature. Any computer on the network with
the Software installed can enable or disable any other
computer from the reports feature.
In addition, Cisco may collect and store detailed
information regarding your network configuration
and usage for the purpose of providing you technical
networking support. The information is associated with
you only when you provide a unique ID number to the
support representative while you are receiving help. The
unique ID is generated randomly on your computer upon
installation and is completely under your control.
Your use of your Cisco product and/or the Software
constitutes consent by you to Cisco’s and/or its affiliates’
collection and use of such information and, for European
Economic Area (EEA) customers, to the transfer of such
information to a location outside the EEA. Any information
collected by your Cisco product and/or the Software is
done and utilized in accordance with our Privacy Policy
available at Privacy Statement. Your election to use the
Cisco product and/or Software indicates your acceptance
of the terms of the Cisco Privacy Policy, so please review
the policy carefully and check the Web site above to
review updates to it.
Software Upgrades etc. If the Software enables you to
receive Upgrades, you may elect at any time to receive
these Upgrades either automatically or manually. If you
elect to receive Upgrades manually or you otherwise
elect not to receive or be notified of any Upgrades, you
may expose your Cisco product and/or the Software to
serious security threats and/or some features within your
Cisco product and/or Software may become inaccessible.
There may be circumstances where we apply an Upgrade
automatically in order to comply with changes in
legislation, legal, security or regulatory requirements or
as a result of requirements to comply with the terms of
any agreements Cisco has with any third parties regarding
your Cisco product and/or the Software. You will always
be notified of any Upgrades being delivered to you. The
terms of this license will apply to any such Upgrade unless
the Upgrade in question is accompanied by a separate
license, in which event the terms of that license will
apply.
Changes to Browser Settings and Error Processing. By
installing the Software, you acknowledge and agree that
the Software may change certain settings in your Internet
browser software, including the default settings for search
provider and source of DNS error pages and may direct
erroneous URLs to an error landing page hosted by Cisco.
You may opt out of these settings by not accepting them as
Ultra RangePlus Wireless-N Access Point with Dual-Band
Software End User License Agreement
part of the installation process or by requesting a change
to your software settings in the error process. Installing
the software and changing these software settings may
conflict with license agreements you have entered into
with other entities, such as your Internet service provider.
Error queries that are libelous, slanderous, defamatory or
that may violate the intellectual property rights of others
may not be processed by Cisco or its suppliers.
Term and Termination. You may terminate this License
at any time by destroying all copies of the Software
and documentation. Your rights under this License will
terminate immediately without notice from Cisco if you
fail to comply with any provision of this Agreement.
Limited Warranty. Cisco additionally warrants that any
media on which the Software may be provided will be
free from defects in materials and workmanship under
normal use for a period of ninety (90) days from the date
of original purchase. Your exclusive remedy and Cisco’s
entire liability under this limited warranty will be for Cisco,
at its option, to (a) replace the Software media, or (b)
refund the purchase price of the Software media.
EXCEPT FOR THE LIMITED WARRANTY ON MEDIA
SET FORTH ABOVE AND TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, ALL SOFTWARE AND
SERVICES PROVIDED BY CISCO ARE PROVIDED “AS IS” WITH
ALL FAULTS AND WITHOUT WARRANTY OF ANY KIND.
Without limiting the foregoing, Cisco does not warrant
that the operation of the product, software or services will
be uninterrupted or error free. Also, due to the continual
development of new techniques for intruding upon and
attacking networks, Cisco does not warrant that the
product, software or services, or any equipment, system
or network on which the product, software or services
are used will be free of vulnerability to intrusion or attack.
The product may include or be bundled with third party
software or service offerings. This limited warranty shall
not apply to such third party software or service offerings.
This limited warranty does not guarantee any continued
availability of a third party’s service for which this product’s
use or operation may require.
TO THE EXTENT NOT PROHIBITED BY APPLICABLE
LAW, ALL IMPLIED WARRANTIES AND CONDITIONS
OF
MERCHANTABILITY,
SATISFACTORY
QUALITY,
NONINFRINGEMENT OR FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED TO THE DURATION OF THE
WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED
CONDITIONS, REPRESENTATIONS AND WARRANTIES ARE
DISCLAIMED. Some jurisdictions do not allow limitations
on how long an implied warranty lasts, so the above
limitation may not apply to you. This limited warranty
gives you specific legal rights, and you may also have
other rights which vary by jurisdiction.
27
Appendix E
Software End User License Agreement
Disclaimer of Liabilities. TO THE EXTENT NOT PROHIBITED
BY APPLICABLE LAW, IN NO EVENT WILL CISCO BE LIABLE
FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL,
INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE
DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY
(INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED
TO THE USE OF OR INABILITY TO USE THE PRODUCT,
SOFTWARE OR ANY SERVICES PROVIDED IN RESPECT
OF SUCH PRODUCT OR SOFTWARE, EVEN IF CISCO HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW,
IN NO EVENT WILL CISCO’S LIABILITY EXCEED THE
AMOUNT PAID BY YOU FOR THE PRODUCT. IF YOU LIVE
IN THE EUROPEAN UNION, REFERENCES TO “SPECIAL,
INDIRECT, CONSEQUENTIAL, PUNITIVE OR INCIDENTAL
DAMAGES” SHALL MEAN ANY LOSSES WHICH (i) WERE NOT
REASONABLY FORESEEABLE BY BOTH PARTIES, AND/OR (ii)
WERE KNOWN TO YOU BUT NOT TO US AND/OR (iii) WERE
REASONABLY FORESEEABLE BY BOTH PARTIES BUT COULD
HAVE BEEN PREVENTED BY YOU SUCH AS, FOR EXAMPLE
(BUT WITHOUT LIMITATION), LOSSES CAUSED BY VIRUSES,
TROJANS OR OTHER MALICIOUS PROGRAMS, OR LOSS OF
OR DAMAGE TO YOUR DATA. The foregoing limitations will
apply even if any warranty or remedy provided under this
limited warranty fails of its essential purpose.
supersedes any conflicting or additional terms contained
in any purchase order or elsewhere.
Technical Support. This limited warranty is neither
a service nor a support contract. Information about
Cisco’s current technical support offerings and policies
(including any fees for support services) can be found at
www.linksysbycisco.com/support.
Terms of Service for Subscription Licenses. These Terms
of Service only apply if you have obtained a subscription
license to Network Magic as specified in your order. Such
subscription licenses may subject you to fees which you
are responsible for paying in order to continue to subscribe
to the Services.
Export. Software, including technical data, may be subject
to U.S. export control laws and regulations and/or export
or import regulations in other countries. You agree to
comply strictly with all such laws and regulations.
U.S. Government Users. The Software and Documentation
qualify as “commercial items” as defined at 48 C.F.R. 2.101
and 48 C.F.R. 12.212. All Government users acquire the
Software and Documentation with only those rights
herein that apply to non-governmental customers. Use of
either the Software or Documentation or both constitutes
agreement by the Government that the Software and
Documentation are “commercial computer software”
and “commercial computer software documentation,”
and constitutes acceptance of the rights and restrictions
herein.
General Terms. This Agreement will be governed by and
construed in accordance with the laws of the State of
California, without reference to conflict of laws principles.
The United Nations Convention on Contracts for the
International Sale of Goods will not apply. If any portion
of this Agreement is found to be void or unenforceable,
the remaining provisions will remain in full force and
effect. This Agreement constitutes the entire agreement
between the parties with respect to the Software and
Ultra RangePlus Wireless-N Access Point with Dual-Band
Linksys, Cisco and the Cisco Logo and other trademarks
contained in the Software and Documentation are
trademarks or registered trademarks of Linksys, Cisco,
its licensors and third parties, as the case may be. You
may not remove or alter any trademark, trade names,
product names, logo, copyright or other proprietary
notices, legends, symbols or labels in the Software and
Documentation. This Agreement does not authorize
you to use Cisco’s or its licensors’ names or respective
trademarks.
END OF SCHEDULE 1
Schedule 2
Network Magic Features
Network Magic License Restrictions. Other than as
set forth in this Agreement or as otherwise permitted
by Cisco, you may not install or execute the Network
Magic Software on any non-personal computer product,
including, but not limited to, a Web appliance, set top box,
handheld device, phone, Web pad device, or any device
running the Microsoft Windows CE operating system.
1. Network Magic Cancellation. You may cancel the
Services at any time. If you cancel the Services, Cisco
will not be obligated to provide you any Network Magic
product Upgrades. If you cancel the Services, Cisco may
delete data relating to you or your use of the Services
from Cisco or its suppliers’ servers. To the extent not
prohibited by applicable law, you understand and agree
that cancellation of your Services is your sole remedy with
respect to any dispute with Cisco.
2. Modifications. Cisco may modify or cancel the terms
of this Agreement or the price, content, or nature of the
Services (including discontinuing the Services program),
upon notice to you. If Cisco modifies any of these
terms, you may cancel the Service by providing written
notice to Cisco via www.networkmagic.com/support
of such cancellation and uninstalling the Software and
discontinuing your use of the Service. Cisco may provide
notice by e-mail, via Network Magic, or by publishing the
changes on its Web site.
3. Email Notification. Cisco may send you email from
time to time to let you know about new products and
services that are available to you. You will be able to optout of receiving these emails using the link provided
within the email. Cisco reserves the right, however, to
28
Appendix E
send you Service related email messages as long as you
are a subscriber to the Service. If you wish to opt-out
of receiving Service related email messages, you may
cancel the Service by providing written notice via www.
networkmagic.com/support to Cisco of such cancellation
and uninstalling the Software and discontinuing your use
of the Service.
END OF SCHEDULE 2
Schedule 3
Open Source and Third Party Licenses
Schedule 3-A
If this Cisco product contains open source software
licensed under Version 2 of the “GNU General Public
License” then the license terms below in this Schedule 3-A
will apply to that open source software. The license terms
below in this Schedule 3-A are from the public web site at
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright © 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
USA
Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the
GNU General Public License is intended to guarantee your
freedom to share and change free software—to make
sure the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s
software and to any other program whose authors
commit to using it. (Some other Free Software Foundation
software is covered by the GNU Lesser General Public
License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to
freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to
distribute copies of free software (and charge for this
service if you wish), that you receive source code or can
get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know
you can do these things.
Software End User License Agreement
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must give the recipients
all the rights that you have. You must make sure that they,
too, receive or can get the source code. And you must
show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the
software, and (2) offer you this license which gives you
legal permission to copy, distribute and/or modify the
software.
Also, for each author’s protection and ours, we want to
make certain that everyone understands that there is no
warranty for this free software. If the software is modified
by someone else and passed on, we want its recipients
to know that what they have is not the original, so that
any problems introduced by others will not reflect on the
original authors’ reputations.
Finally, any free program is threatened constantly by
software patents. We wish to avoid the danger that
redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary.
To prevent this, we have made it clear that any patent must
be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution
and modification follow.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License applies to any program or other work
which contains a notice placed by the copyright
holder saying it may be distributed under the terms
of this General Public License. The “Program”, below,
refers to any such program or work, and a “work
based on the Program” means either the Program
or any derivative work under copyright law: that is
to say, a work containing the Program or a portion
of it, either verbatim or with modifications and/
or translated into another language. (Hereinafter,
translation is included without limitation in the term
“modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and
modification are not covered by this License; they
are outside its scope. The act of running the Program
is not restricted, and the output from the Program is
covered only if its contents constitute a work based on
the Program (independent of having been made by
running the Program). Whether that is true depends
on what the Program does.
To protect your rights, we need to make restrictions that
forbid anyone to deny you these rights or to ask you to
surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the
software, or if you modify it.
Ultra RangePlus Wireless-N Access Point with Dual-Band
29
Appendix E
1. You may copy and distribute verbatim copies of the
Program’s source code as you receive it, in any medium,
provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice
and disclaimer of warranty; keep intact all the notices
that refer to this License and to the absence of any
warranty; and give any other recipients of the Program
a copy of this License along with the Program.
Software End User License Agreement
distribution of derivative or collective works based on
the Program.
In addition, mere aggregation of another work not
based on the Program with the Program (or with a
work based on the Program) on a volume of a storage
or distribution medium does not bring the other work
under the scope of this License.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee. .
3. You may copy and distribute the Program (or a
work based on it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2
above provided that you also do one of the following:
2. You may modify your copy or copies of the Program
or any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications
or work under the terms of Section 1 above, provided
that you also meet all of these conditions:
a) Accompany it with the complete corresponding
machine-readable source code, which must be
distributed under the terms of Sections 1 and 2
above on a medium customarily used for software
interchange; or,
a) You must cause the modified files to carry
prominent notices stating that you changed the
files and the date of any change.
b) Accompany it with a written offer, valid for at least
three years, to give any third party, for a charge
no more than your cost of physically performing
source distribution, a complete machine-readable
copy of the corresponding source code, to be
distributed under the terms of Sections 1 and 2
above on a medium customarily used for software
interchange; or,
b) You must cause any work that you distribute or
publish, that in whole or in part contains or is
derived from the Program or any part thereof, to be
licensed as a whole at no charge to all third parties
under the terms of this License.
c) If the modified program normally reads commands
interactively when run, you must cause it, when
started running for such interactive use in the most
ordinary way, to print or display an announcement
including an appropriate copyright notice and
a notice that there is no warranty (or else, saying
that you provide a warranty) and that users may
redistribute the program under these conditions,
and telling the user how to view a copy of
this License. (Exception: if the Program itself is
interactive but does not normally print such an
announcement, your work based on the Program
is not required to print an announcement.)
These requirements apply to the modified work as
a whole. If identifiable sections of that work are not
derived from the Program, and can be reasonably
considered independent and separate works in
themselves, then this License, and its terms, do not
apply to those sections when you distribute them as
separate works. But when you distribute the same
sections as part of a whole which is a work based on
the Program, the distribution of the whole must be on
the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights
or contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the
Ultra RangePlus Wireless-N Access Point with Dual-Band
c) Accompany it with the information you received as
to the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial
distribution and only if you received the program
in object code or executable form with such an
offer, in accord with Subsection b above.)
The source code for a work means the preferred form
of the work for making modifications to it. For an
executable work, complete source code means all
the source code for all modules it contains, plus any
associated interface definition files, plus the scripts
used to control compilation and installation of the
executable. However, as a special exception, the source
code distributed need not include anything that is
normally distributed (in either source or binary form)
with the major components (compiler, kernel, and so
on) of the operating system on which the executable
runs, unless that component itself accompanies the
executable.
If distribution of executable or object code is made
by offering access to copy from a designated place,
then offering equivalent access to copy the source
code from the same place counts as distribution of
the source code, even though third parties are not
compelled to copy the source along with the object
code.
30
Appendix E
4. You may not copy, modify, sublicense, or distribute
the Program except as expressly provided under
this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will
automatically terminate your rights under this License.
However, parties who have received copies, or rights,
from you under this License will not have their licenses
terminated so long as such parties remain in full
compliance.
5. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Program or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying
or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License
to do so, and all its terms and conditions for copying,
distributing or modifying the Program or works based
on it.
6. Each time you redistribute the Program (or any work
based on the Program), the recipient automatically
receives a license from the original licensor to copy,
distribute or modify the Program subject to these
terms and conditions. You may not impose any further
restrictions on the recipients’ exercise of the rights
granted herein. You are not responsible for enforcing
compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise)
that contradict the conditions of this License, they do
not excuse you from the conditions of this License. If
you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other
pertinent obligations, then as a consequence you
may not distribute the Program at all. For example,
if a patent license would not permit royalty-free
redistribution of the Program by all those who receive
copies directly or indirectly through you, then the only
way you could satisfy both it and this License would be
to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or
unenforceable under any particular circumstance,
the balance of the section is intended to apply and
the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or
to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free
software distribution system, which is implemented
by public license practices. Many people have
made generous contributions to the wide range of
software distributed through that system in reliance
Ultra RangePlus Wireless-N Access Point with Dual-Band
Software End User License Agreement
on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to
distribute software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly clear
what is believed to be a consequence of the rest of this
License.
8. If the distribution and/or use of the Program is
restricted in certain countries either by patents or by
copyrighted interfaces, the original copyright holder
who places the Program under this License may add an
explicit geographical distribution limitation excluding
those countries, so that distribution is permitted only
in or among countries not thus excluded. In such case,
this License incorporates the limitation as if written in
the body of this License.
9. The Free Software Foundation may publish revised
and/or new versions of the General Public License
from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version number.
If the Program specifies a version number of this
License which applies to it and “any later version”, you
have the option of following the terms and conditions
either of that version or of any later version published
by the Free Software Foundation. If the Program does
not specify a version number of this License, you
may choose any version ever published by the Free
Software Foundation.
10. If you wish to incorporate parts of the Program into
other free programs whose distribution conditions are
different, write to the author to ask for permission. For
software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will
be guided by the two goals of preserving the free status
of all derivatives of our free software and of promoting
the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
31
Appendix E
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE,
BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR
A FAILURE OF THE PROGRAM TO OPERATE WITH ANY
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES
END OF TERMS AND CONDITIONS
END OF SCHEDULE 3-A
Schedule 3-B
If this Cisco product contains open source software licensed
under Version 2.1 of the “GNU Lesser General Public
License” then the license terms below in this Schedule 3-B
will apply to that open source software. The license terms
below in this Schedule 3-B are from the public web site at
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright © 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301
USA
Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
[This is the first released version of the Lesser GPL. It also
counts as the successor of the GNU Library Public License,
version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your
freedom to share and change free software—to make
sure the software is free for all its users.
This license, the Lesser General Public License, applies to
some specially designated software packages—typically
libraries—of the Free Software Foundation and other
authors who decide to use it. You can use it too, but we
suggest you first think carefully about whether this license
or the ordinary General Public License is the better strategy
to use in any particular case, based on the explanations
below.
Ultra RangePlus Wireless-N Access Point with Dual-Band
Software End User License Agreement
When we speak of free software, we are referring to
freedom of use, not price. Our General Public Licenses
are designed to make sure that you have the freedom
to distribute copies of free software (and charge for this
service if you wish); that you receive source code or can
get it if you want it; that you can change the software and
use pieces of it in new free programs; and that you are
informed that you can do these things.
To protect your rights, we need to make restrictions that
forbid distributors to deny you these rights or to ask you
to surrender these rights. These restrictions translate to
certain responsibilities for you if you distribute copies of
the library or if you modify it.
For example, if you distribute copies of the library,
whether gratis or for a fee, you must give the recipients
all the rights that we gave you. You must make sure that
they, too, receive or can get the source code. If you link
other code with the library, you must provide complete
object files to the recipients, so that they can relink them
with the library after making changes to the library and
recompiling it. And you must show them these terms so
they know their rights.
We protect your rights with a two-step method: (1) we
copyright the library, and (2) we offer you this license,
which gives you legal permission to copy, distribute and/
or modify the library.
To protect each distributor, we want to make it very clear
that there is no warranty for the free library. Also, if the
library is modified by someone else and passed on, the
recipients should know that what they have is not the
original version, so that the original author’s reputation
will not be affected by problems that might be introduced
by others.
Finally, software patents pose a constant threat to the
existence of any free program. We wish to make sure
that a company cannot effectively restrict the users of
a free program by obtaining a restrictive license from a
patent holder. Therefore, we insist that any patent license
obtained for a version of the library must be consistent
with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered
by the ordinary GNU General Public License. This license,
the GNU Lesser General Public License, applies to certain
designated libraries, and is quite different from the
ordinary General Public License. We use this license for
certain libraries in order to permit linking those libraries
into non-free programs.
When a program is linked with a library, whether
statically or using a shared library, the combination of
the two is legally speaking a combined work, a derivative
of the original library. The ordinary General Public
License therefore permits such linking only if the entire
combination fits its criteria of freedom. The Lesser General
32
Appendix E
Public License permits more lax criteria for linking other
code with the library.
We call this license the “Lesser” General Public License
because it does Less to protect the user’s freedom than
the ordinary General Public License. It also provides
other free software developers Less of an advantage over
competing non-free programs. These disadvantages are
the reason we use the ordinary General Public License
for many libraries. However, the Lesser license provides
advantages in certain special circumstances.
For example, on rare occasions, there may be a special
need to encourage the widest possible use of a certain
library, so that it becomes a de-facto standard. To achieve
this, non-free programs must be allowed to use the library.
A more frequent case is that a free library does the same
job as widely used non-free libraries. In this case, there is
little to gain by limiting the free library to free software
only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use
a large body of free software. For example, permission to
use the GNU C Library in non-free programs enables many
more people to use the whole GNU operating system, as
well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less
protective of the users’ freedom, it does ensure that the
user of a program that is linked with the Library has the
freedom and the wherewithal to run that program using a
modified version of the Library.
The precise terms and conditions for copying, distribution
and modification follow. Pay close attention to the
difference between a “work based on the library” and a
“work that uses the library”. The former contains code
derived from the library, whereas the latter must be
combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
AND MODIFICATION
0. This License Agreement applies to any software library
or other program which contains a notice placed by
the copyright holder or other authorized party saying
it may be distributed under the terms of this Lesser
General Public License (also called “this License”). Each
licensee is addressed as “you”.
A “library” means a collection of software functions
and/or data prepared so as to be conveniently linked
with application programs (which use some of those
functions and data) to form executables.
The “Library”, below, refers to any such software library
or work which has been distributed under these terms.
A “work based on the Library” means either the Library
or any derivative work under copyright law: that is to
say, a work containing the Library or a portion of it,
Ultra RangePlus Wireless-N Access Point with Dual-Band
Software End User License Agreement
either verbatim or with modifications and/or translated
straightforwardly into another language. (Hereinafter,
translation is included without limitation in the term
“modification”.)
“Source code” for a work means the preferred form of
the work for making modifications to it. For a library,
complete source code means all the source code for
all modules it contains, plus any associated interface
definition files, plus the scripts used to control
compilation and installation of the library.
Activities other than copying, distribution and
modification are not covered by this License; they are
outside its scope. The act of running a program using
the Library is not restricted, and output from such a
program is covered only if its contents constitute a
work based on the Library (independent of the use
of the Library in a tool for writing it). Whether that is
true depends on what the Library does and what the
program that uses the Library does.
1. You may copy and distribute verbatim copies of the
Library’s complete source code as you receive it, in
any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this License and to
the absence of any warranty; and distribute a copy of
this License along with the Library.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Library or
any portion of it, thus forming a work based on the
Library, and copy and distribute such modifications
or work under the terms of Section 1 above, provided
that you also meet all of these conditions:
a) The modified work must itself be a software
library.
b) You must cause the files modified to carry
prominent notices stating that you changed the
files and the date of any change.
c) You must cause the whole of the work to be
licensed at no charge to all third parties under the
terms of this License.
d) If a facility in the modified Library refers to a function
or a table of data to be supplied by an application
program that uses the facility, other than as an
argument passed when the facility is invoked, then
you must make a good faith effort to ensure that,
in the event an application does not supply such
function or table, the facility still operates, and
performs whatever part of its purpose remains
meaningful.
33
Appendix E
Software End User License Agreement
(For example, a function in a library to compute square
roots has a purpose that is entirely well-defined
independent of the application. Therefore, Subsection
2d requires that any application-supplied function or
table used by this function must be optional: if the
application does not supply it, the square root function
must still compute square roots.)
If distribution of object code is made by offering
access to copy from a designated place, then offering
equivalent access to copy the source code from the
same place satisfies the requirement to distribute
the source code, even though third parties are not
compelled to copy the source along with the object
code.
These requirements apply to the modified work as
a whole. If identifiable sections of that work are not
derived from the Library, and can be reasonably
considered independent and separate works in
themselves, then this License, and its terms, do not
apply to those sections when you distribute them as
separate works. But when you distribute the same
sections as part of a whole which is a work based on
the Library, the distribution of the whole must be on
the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
5. A program that contains no derivative of any portion
of the Library, but is designed to work with the Library
by being compiled or linked with it, is called a “work
that uses the Library”. Such a work, in isolation, is not
a derivative work of the Library, and therefore falls
outside the scope of this License.
Thus, it is not the intent of this section to claim rights
or contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on
the Library.
When a “work that uses the Library” uses material from
a header file that is part of the Library, the object code
for the work may be a derivative work of the Library
even though the source code is not. Whether this is
true is especially significant if the work can be linked
without the Library, or if the work is itself a library. The
threshold for this to be true is not precisely defined by
law.
In addition, mere aggregation of another work not
based on the Library with the Library (or with a work
based on the Library) on a volume of a storage or
distribution medium does not bring the other work
under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU
General Public License instead of this License to a
given copy of the Library. To do this, you must alter all
the notices that refer to this License, so that they refer
to the ordinary GNU General Public License, version
2, instead of to this License. (If a newer version than
version 2 of the ordinary GNU General Public License
has appeared, then you can specify that version
instead if you wish.) Do not make any other change in
these notices.
Once this change is made in a given copy, it is
irreversible for that copy, so the ordinary GNU General
Public License applies to all subsequent copies and
derivative works made from that copy.
This option is useful when you wish to copy part of the
code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion
or derivative of it, under Section 2) in object code or
executable form under the terms of Sections 1 and
2 above provided that you accompany it with the
complete corresponding machine-readable source
code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used
for software interchange.
Ultra RangePlus Wireless-N Access Point with Dual-Band
However, linking a “work that uses the Library” with
the Library creates an executable that is a derivative
of the Library (because it contains portions of the
Library), rather than a “work that uses the library”. The
executable is therefore covered by this License. Section
6 states terms for distribution of such executables.
If such an object file uses only numerical parameters,
data structure layouts and accessors, and small macros
and small inline functions (ten lines or less in length),
then the use of the object file is unrestricted, regardless
of whether it is legally a derivative work. (Executables
containing this object code plus portions of the Library
will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you
may distribute the object code for the work under the
terms of Section 6. Any executables containing that
work also fall under Section 6, whether or not they are
linked directly with the Library itself.
6. As an exception to the Sections above, you may also
combine or link a “work that uses the Library” with the
Library to produce a work containing portions of the
Library, and distribute that work under terms of your
choice, provided that the terms permit modification
of the work for the customer’s own use and reverse
engineering for debugging such modifications.
You must give prominent notice with each copy of
the work that the Library is used in it and that the
Library and its use are covered by this License. You
must supply a copy of this License. If the work during
execution displays copyright notices, you must include
the copyright notice for the Library among them, as
well as a reference directing the user to the copy of this
License. Also, you must do one of these things:
34
Appendix E
a) Accompany the work with the complete
corresponding machine-readable source code
for the Library including whatever changes were
used in the work (which must be distributed
under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the
complete machine-readable “work that uses the
Library”, as object code and/or source code, so that
the user can modify the Library and then relink
to produce a modified executable containing the
modified Library. (It is understood that the user
who changes the contents of definitions files in the
Library will not necessarily be able to recompile the
application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking
with the Library. A suitable mechanism is one that
(1) uses at run time a copy of the library already
present on the user’s computer system, rather than
copying library functions into the executable, and
(2) will operate properly with a modified version of
the library, if the user installs one, as long as the
modified version is interface-compatible with the
version that the work was made with.
c) Accompany the work with a written offer, valid
for at least three years, to give the same user the
materials specified in Subsection 6a, above, for a
charge no more than the cost of performing this
distribution.
d) If distribution of the work is made by offering access
to copy from a designated place, offer equivalent
access to copy the above specified materials from
the same place.
e) Verify that the user has already received a copy of
these materials or that you have already sent this
user a copy.
For an executable, the required form of the “work that
uses the Library” must include any data and utility
programs needed for reproducing the executable from
it. However, as a special exception, the materials to be
distributed need not include anything that is normally
distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless
that component itself accompanies the executable.
Software End User License Agreement
7. You may place library facilities that are a work based
on the Library side-by-side in a single library together
with other library facilities not covered by this License,
and distribute such a combined library, provided that
the separate distribution of the work based on the
Library and of the other library facilities is otherwise
permitted, and provided that you do these two things:
a) Accompany the combined library with a copy of the
same work based on the Library, uncombined with
any other library facilities. This must be distributed
under the terms of the Sections above.
b) Give prominent notice with the combined library of
the fact that part of it is a work based on the Library,
and explaining where to find the accompanying
uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or
distribute the Library except as expressly provided
under this License. Any attempt otherwise to copy,
modify, sublicense, link with, or distribute the Library
is void, and will automatically terminate your rights
under this License. However, parties who have received
copies, or rights, from you under this License will not
have their licenses terminated so long as such parties
remain in full compliance.
9. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Library or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying
or distributing the Library (or any work based on the
Library), you indicate your acceptance of this License
to do so, and all its terms and conditions for copying,
distributing or modifying the Library or works based
on it.
10. Each time you redistribute the Library (or any work
based on the Library), the recipient automatically
receives a license from the original licensor to copy,
distribute, link with or modify the Library subject
to these terms and conditions. You may not impose
any further restrictions on the recipients’ exercise of
the rights granted herein. You are not responsible
for enforcing compliance by third parties with this
License.
It may happen that this requirement contradicts the
license restrictions of other proprietary libraries that
do not normally accompany the operating system.
Such a contradiction means you cannot use both
them and the Library together in an executable that
you distribute.
Ultra RangePlus Wireless-N Access Point with Dual-Band
35
Appendix E
11. If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on
you (whether by court order, agreement or otherwise)
that contradict the conditions of this License, they do
not excuse you from the conditions of this License. If
you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other
pertinent obligations, then as a consequence you may
not distribute the Library at all. For example, if a patent
license would not permit royalty-free redistribution of
the Library by all those who receive copies directly or
indirectly through you, then the only way you could
satisfy both it and this License would be to refrain
entirely from distribution of the Library.
If any portion of this section is held invalid or
unenforceable under any particular circumstance,
the balance of the section is intended to apply, and
the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or
to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free
software distribution system which is implemented
by public license practices. Many people have
made generous contributions to the wide range of
software distributed through that system in reliance
on consistent application of that system; it is up to
the author/donor to decide if he or she is willing to
distribute software through any other system and a
licensee cannot impose that choice.
This section is intended to make thoroughly clear
what is believed to be a consequence of the rest of this
License.
12. If the distribution and/or use of the Library is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places
the Library under this License may add an explicit
geographical distribution limitation excluding those
countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the
body of this License.
Software End User License Agreement
license version number, you may choose any version
ever published by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into
other free programs whose distribution conditions are
incompatible with these, write to the author to ask for
permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for
this. Our decision will be guided by the two goals of
preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of
software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE LIBRARY, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE
LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD
THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE
COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW
OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY
AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE THE LIBRARY (INCLUDING
BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY
TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
END OF SCHEDULE 3-B
13. The Free Software Foundation may publish revised
and/or new versions of the Lesser General Public
License from time to time. Such new versions will be
similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number.
If the Library specifies a version number of this License
which applies to it and “any later version”, you have the
option of following the terms and conditions either of
that version or of any later version published by the Free
Software Foundation. If the Library does not specify a
Ultra RangePlus Wireless-N Access Point with Dual-Band
36
Appendix E
Schedule 3-C
OPENSSL LICENSE
If this Cisco product contains open source software
licensed under the OpenSSL license:
This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/).
This product includes cryptographic software written
by Eric Young (eay@cryptsoft.com).
This product includes software written by Tim Hudson
(tjh@cryptsoft.com).
In addition, if this Cisco product contains open source
software licensed under the OpenSSL license then the
license terms below in this Schedule 3-C will apply to
that open source software. The license terms below
in this Schedule 3-C are from the public web site at
http://www.openssl.org/source/license.html.
The OpenSSL toolkit stays under a dual license, i.e. both
the conditions of the OpenSSL License and the original
SSLeay license apply to the toolkit. See below for the
actual license texts. Actually both licenses are BSD-style
Open Source licenses. In case of any license issues related
to OpenSSL please contact openssl-core@openssl.org.
Software End User License Agreement
6. Redistributions of any form whatsoever must retain
the following acknowledgment: “This product includes
software developed by the OpenSSL Project for use in
the OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT
``AS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE
This product includes cryptographic software written by
Eric Young (eay@cryptsoft.com). This product includes
software written by Tim Hudson (tjh@cryptsoft.com).
Original SSLeay License
OpenSSL License
Copyright © 1995-1998 Eric Young (eay@cryptsoft.com)
All rights reserved.
Copyright © 1998-2007 The OpenSSL Project. All rights
reserved.
This package is an SSL implementation written by Eric
Young (eay@cryptsoft.com).
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
The implementation was written so as to conform with
Netscape’s SSL.
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the
following disclaimer.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgment: “This product includes software
developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project”
must not be used to endorse or promote products
derived from this software without prior written
permission. For written permission, please contact
openssl-core@openssl.org.
5. Products derived from this software may not be called
“OpenSSL” nor may “OpenSSL” appear in their names
without prior written permission of the OpenSSL
Project.
Ultra RangePlus Wireless-N Access Point with Dual-Band
This library is free for commercial and non-commercial
use as long as the following conditions are adhered to.
The following conditions apply to all code found in this
distribution, be it the RC4, RSA, lhash, DES, etc., code; not
just the SSL code. The SSL documentation included with
this distribution is covered by the same copyright terms
except that the holder is Tim Hudson (tjh@cryptsoft.
com).
Copyright remains Eric Young’s, and as such any Copyright
notices in the code are not to be removed.
If this package is used in a product, Eric Young should be
given attribution as the author of the parts of the library
used. This can be in the form of a textual message at
program startup or in documentation (online or textual)
provided with the package.
Redistribution and use in source and binary forms, with
or without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the
copyright notice, this list of conditions and the
following disclaimer.
37
Appendix E
Software End User License Agreement
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or
use of this software must display the following
acknowledgement:
“This product includes cryptographic software written
by Eric Young (eay@cryptsoft.com)”
The word ‘cryptographic’ can be left out if the routines
from the library being used are not cryptographic
related.
4. If you include any Windows specific code (or a derivative
thereof ) from the apps directory (application code)
you must include an acknowledgement: “This product
includes software written by Tim Hudson (tjh@
cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS’’
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The license and distribution terms for any publicly available
version or derivative of this code cannot be changed. i.e.
this code cannot simply be copied and put under another
distribution license [including the GNU Public License.]
END OF SCHEDULE 3-C
09041310NC-AI
Ultra RangePlus Wireless-N Access Point with Dual-Band
38

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-701
Startup Profile                 : Print
Producer                        : Adobe PDF Library 9.0
Trapped                         : False
Create Date                     : 2009:04:13 18:53:54-07:00
Modify Date                     : 2009:05:13 16:42:08+08:00
Metadata Date                   : 2009:05:13 16:42:08+08:00
Creator Tool                    : Adobe InDesign CS4 (6.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 7907 bytes, use -b option to extract)
Instance ID                     : uuid:b598ef95-581c-420a-8089-333a8dac372e
Document ID                     : adobe:docid:indd:eea66238-0e96-11de-bee2-8e9e54e2c9f2
Original Document ID            : adobe:docid:indd:eea66238-0e96-11de-bee2-8e9e54e2c9f2
Rendition Class                 : proof:pdf
Derived From Instance ID        : eea66233-0e96-11de-bee2-8e9e54e2c9f2
Derived From Document ID        : adobe:docid:indd:7e255387-c6d3-11dd-ba76-cd6abb69692b
History Action                  : saved, saved
History Instance ID             : xmp.iid:DB42CC138928DE119D41B3997D86481C, xmp.iid:DC42CC138928DE119D41B3997D86481C
History When                    : 2009:04:13 17:29:51-07:00, 2009:04:13 17:29:51-07:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0
History Changed                 : /, /metadata
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 300.00, 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 300.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 72.00, 300.00, 300.00, 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:D819FD6AB7EFDC11886C8824418B8FFA, uuid:7d9c43ff-3a8e-4863-8cb8-d3fd67c91f56, uuid:3c014673-a3b3-4eef-b4c0-f049614e3ed7, uuid:7913CDA7960EDE11A221E19043B870C6, uuid:720a9d92-6699-4f10-addd-c1a036fead8a, uuid:2f88acdd-617c-427a-9108-15f7271ed2a0, uuid:9da639e1-9017-4020-8617-fee87680f534, uuid:268df51b-3bda-4607-b288-233a2a7f5c04, uuid:3AB1624AA70EDE119192F5175C1A5BCA, uuid:bc57354c-2df8-4797-a0e8-c7a6ba264e6e, uuid:8634cb14-fc9c-4724-b0ef-dcbc35b3aebe, uuid:9031b442-7200-4cd4-8bd7-cb86f2cca9a8, uuid:872b26bb-4644-42af-be1a-cf8e7eed68f3, uuid:799933E1A60EDE119192F5175C1A5BCA, uuid:5cb52a1b-6847-4f7c-9113-6f552e39acba, uuid:90d96bae-0323-430e-9db4-8335c475cc05, uuid:30e57f42-7633-4c77-b17b-ab83861ac544, uuid:275c14cb-dc34-45a2-852c-185921140896, uuid:720a9d92-6699-4f10-addd-c1a036fead8a, uuid:720a9d92-6699-4f10-addd-c1a036fead8a, uuid:720a9d92-6699-4f10-addd-c1a036fead8a, uuid:88F5A4EA8199DD1193D2DBBD135F0544, uuid:720a9d92-6699-4f10-addd-c1a036fead8a, uuid:C4B5CE924D13DE1197DDEA6B309388C9, uuid:C8B5CE924D13DE1197DDEA6B309388C9, uuid:0B1F8290A113DE11B7F0911DEE19C56F, uuid:720a9d92-6699-4f10-addd-c1a036fead8a, uuid:60311750A113DE11B7F0911DEE19C56F, uuid:0E1F8290A113DE11B7F0911DEE19C56F, uuid:561279A35513DE1197DDEA6B309388C9, uuid:5C1279A35513DE1197DDEA6B309388C9, uuid:68A3A8B95513DE1197DDEA6B309388C9, uuid:6EA3A8B95513DE1197DDEA6B309388C9, uuid:758809925513DE1197DDEA6B309388C9, uuid:788809925513DE1197DDEA6B309388C9, uuid:728809925513DE1197DDEA6B309388C9, uuid:720a9d92-6699-4f10-addd-c1a036fead8a, uuid:63311750A113DE11B7F0911DEE19C56F, uuid:720a9d92-6699-4f10-addd-c1a036fead8a, uuid:260BD84C5513DE1197DDEA6B309388C9, uuid:230BD84C5513DE1197DDEA6B309388C9, uuid:200BD84C5513DE1197DDEA6B309388C9, uuid:892888325513DE1197DDEA6B309388C9, uuid:777EE38D8113DE11AA3EF030CFB27032, uuid:747EE38D8113DE11AA3EF030CFB27032, uuid:9da639e1-9017-4020-8617-fee87680f534, uuid:2f88acdd-617c-427a-9108-15f7271ed2a0, uuid:2f88acdd-617c-427a-9108-15f7271ed2a0, uuid:2f88acdd-617c-427a-9108-15f7271ed2a0, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9eba4cf1-ce64-44ca-af68-1b35b113ea09, uuid:9da639e1-9017-4020-8617-fee87680f534
Manifest Reference Document ID  : uuid:D719FD6AB7EFDC11886C8824418B8FFA, uuid:18B0122C8BEFDC119AC4860DC6351738, uuid:1AB0122C8BEFDC119AC4860DC6351738, uuid:7813CDA7960EDE11A221E19043B870C6, uuid:C6630B259416DB119752CE0FD4DE5706, uuid:872B750B9B16DB119752CE0FD4DE5706, uuid:C1630B259416DB119752CE0FD4DE5706, uuid:5B359B8CE962DC118B28B955CDF7556C, uuid:7C9933E1A60EDE119192F5175C1A5BCA, uuid:A1572EC97282DC11A5B39B97561417CE, uuid:48E9EFB92F9ADD11A8B7CEEA7B6CB8A1, uuid:7654656B6D82DC11A5B39B97561417CE, uuid:7C54656B6D82DC11A5B39B97561417CE, uuid:789933E1A60EDE119192F5175C1A5BCA, uuid:4AE9EFB92F9ADD11A8B7CEEA7B6CB8A1, uuid:02993C8463FADB1194DEA08FF816110E, uuid:DA357606212EDB11B82CA77C2B86F09F, uuid:7AF96653F60DDB11BAAC8C40D481A301, uuid:C6630B259416DB119752CE0FD4DE5706, uuid:C6630B259416DB119752CE0FD4DE5706, uuid:C6630B259416DB119752CE0FD4DE5706, uuid:C6630B259416DB119752CE0FD4DE5706, uuid:C3B5CE924D13DE1197DDEA6B309388C9, uuid:C7B5CE924D13DE1197DDEA6B309388C9, uuid:C6630B259416DB119752CE0FD4DE5706, uuid:C6630B259416DB119752CE0FD4DE5706, uuid:C6630B259416DB119752CE0FD4DE5706, uuid:C1630B259416DB119752CE0FD4DE5706, uuid:872B750B9B16DB119752CE0FD4DE5706, uuid:872B750B9B16DB119752CE0FD4DE5706, uuid:872B750B9B16DB119752CE0FD4DE5706, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:53D6E26581BCDB11B14BE839F33BF7D3, uuid:C1630B259416DB119752CE0FD4DE5706
Format                          : application/pdf
Title                           : WAP610N User Guide
Creator                         : Linksys by Cisco
Has XFA                         : No
Page Count                      : 42
Page Layout                     : SinglePage
Author                          : Linksys by Cisco

EXIF Metadata provided by EXIF.tools