LINKSYS WES610NV2 4-Port Dual-Band N Entertainment Bridge User Manual

LINKSYS LLC 4-Port Dual-Band N Entertainment Bridge

UserManual.wiki >

WES610NV2 User Manual >

Contents

1. User Manual
2. User Manual - Statements

User Manual

User GuideLinksys WET610N/WES610N Dual-Band N Entertainment Bridge

iContentsLinksys E-SeriesiProduct OverviewLED panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Ports panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Wireless Security ChecklistChange the default wireless network name or SSID 4Change the default password 4Enable MAC address ﬁltering 4Enable encryption 4General Network Security Guidelines. . . . . . . . . . . . . . . . . .4Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . .5Advanced ConﬁgurationHow to access the browser-based utility . . . . . . . . . . . . . . . .6Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7Language 7Network Setup 7Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . .7Basic Wireless Settings 8Wireless Security 8Wi-Fi Protected Setup 9Wireless > Wireless Network Site Survey . . . . . . . . . . . . . . . 10Wireless Network Site Survey 10Wireless > WMM® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11WMM 12Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . 13Advanced Wireless 13Administration > Management . . . . . . . . . . . . . . . . . . . . 14Management 14Administration > Factory Defaults . . . . . . . . . . . . . . . . . . . 15Factory Defaults 15Administration > Upgrade Firmware . . . . . . . . . . . . . . . . . 15Upgrade Firmware 15Status > Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Bridge Information 16Local Network 16Status > Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Wireless 16TroubleshootingWES610N/WET610N 17SpeciﬁcationsWES610N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18WET610N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Contents

2Product OverviewLinksys WES610N/WET610N2Thank you for choosing the Linksys Dual-Band N Entertainment Bridge. The bridge can connect any wired, Ethernet device to your wireless network. The bridge is based on dual-band Wireless-N, so it is compatible with any Wireless-N, -G, -A, or -B router or access point. For first-time installation, follow the steps on the CD folder. To configure advanced settings, use the convenient, browser-based utility.LED panelWES610N WET610NWireless (Blue) The Wireless LED lights up when there is a wireless connection. The LED flashes when the bridge is actively sending or receiving data over the wireless network.Wi-Fi Protected Setup Button If your router supports Wi-Fi Protected Setup and uses WPA or WPA2 security, then you can use Wi-Fi Protected Setup to automatically connect the bridge. To use Wi-Fi Protected Setup, refer to “Wireless > Basic Wireless Settings” on page 7.Wi-Fi Protected Setup LED (Blue/Amber) The LED flashes blue for two minutes during Wi-Fi Protected Setup. It lights up blue when wireless security is enabled. If there is an error during the Wi-Fi Protected Setup process, then the LED lights up amber. Make sure the network router supports Wi-Fi Protected Setup. Wait until the LED is off, and then try again. Ethernet (Blue) The Ethernet LED lights up when there is a wired connection. The LED flashes when the bridge is actively sending or receiving data over the Ethernet port(s).Power (Blue) The Power LED lights up when the bridge is powered on.Product Overview

3Product OverviewLinksys WES610N/WET610NPorts panelWES610N WET610NEthernet The Ethernet port(s) connects the bridge to a computer or other Ethernet network device. The WES610N has four ports, and the WET610N has a single port.Reset There are two ways to reset the bridge’s factory defaults. Either press and hold the Reset button for approximately five seconds, or restore the defaults from Administration > Factory Defaults in the bridge’s browser-based utility. The WES610N has a reset button on the bottom, and the WET610N has a reset button on the back port panel.Power The Power port connects the bridge to the included power adapter.

4Wireless Security ChecklistLinksys WES610N/WET610N4Wireless networks are convenient and easy to install, so homes with high-speed Internet access are adopting them at a rapid pace. Because wireless networking operates by sending information over radio waves, it can be more vulnerable to intruders than a traditional wired network. Like signals from your cellular or cordless phones, signals from your wireless network can also be intercepted. Since you cannot physically prevent someone from connecting to your wireless network, you need to take some additional steps to keep your network secure. Change the default wireless network name or SSIDWireless devices have a default wireless network name or Service Set Identifier (SSID) set by the factory. This is the name of your wireless network, and can be up to 32 characters in length. Linksys wireless products use linksys as the default wireless network name. You should change the wireless network name to something unique to distinguish your wireless network from other wireless networks that may exist around you, but do not use personal information (such as your Social Security number) because this information may be available for anyone to see when browsing for wireless networks. Change the default passwordFor wireless products such as access points and routers, you will be asked for a password when you want to change their settings. These devices have a default password set by the factory. The Linksys default password is admin. Hackers know these defaults and may try to use them to access your wireless device and change your network settings. To thwart any unauthorized changes, customize the device’s password so it will be hard to guess.Enable MAC address filteringLinksys routers give you the ability to enable Media Access Control (MAC) address filtering. The MAC address is a unique series of numbers and letters assigned to every networking device. With MAC address filtering enabled, wireless network access is provided solely for wireless devices with specific MAC addresses. For example, you can specify the MAC address of each computer in your home so that only those computers can access your wireless network. Enable encryptionEncryption protects data transmitted over a wireless network. Wi-Fi Protected Access (WPA/WPA2) and Wired Equivalent Privacy (WEP) offer different levels of security for wireless communication.A network encrypted with WPA/WPA2 is more secure than a network encrypted with WEP, because WPA/WPA2 uses dynamic key encryption. To protect the information as it passes over the airwaves, you should enable the highest level of encryption supported by your network equipment. WEP is an older encryption standard and may be the only option available on some older devices that do not support WPA.General Network Security GuidelinesWireless network security is useless if the underlying network is not secure. • Password protect all computers on the network and individually password protect sensitive files. • Change passwords on a regular basis. • Install anti-virus software and personal firewall software. • Disable file sharing (peer-to-peer). Some applications may open file sharing without your consent and/or knowledge.Wireless Security Checklist

5Wireless Security ChecklistLinksys WES610N/WET610NAdditional Security Tips • Keep wireless routers, access points, or gateways away from exterior walls and windows. • Turn wireless routers, access points, or gateways off when they are not being used (at night, during vacations). • Use strong passphrases that are at least eight characters in length. Combine letters and numbers to avoid using standard words that can be found in the dictionary.

6Advanced ConfigurationLinksys WES610N/WET610N6After setting up the bridge by following the steps on the CD folder, the bridge will be ready for use. However, if you want to change its advanced settings, use the bridge’s browser-based utility. This chapter describes each web page of the utility and each page’s key functions. You can access the utility via a web browser on a computer networked with the bridge.The browser-based utility has these main tabs: Setup, Wireless, Administration, and Status. Additional tabs will be available after you click one of the main tabs.How to access the browser-based utilityUse a web browser to access the browser-based utility.If the bridge is connected to a network with a DHCP server (usually the network router), then the bridge will obtain its IP address from the DHCP server. If there is no DHCP server, then the bridge will use its default static IP address, 169.254.1.250. (If you set a permanent static IP address on the bridge through the browser-based utility, then enter the static IP address instead.)NOTEIf you do not know the bridge’s IP address, then find its IP address in the DHCP clients table of your router. (Refer to the documentation for your router.)If you cannot locate the bridge’s IP address, you can reset the bridge; press the Reset button on the bridge for approximately five seconds, using a straightened paper clip. This will reset the bridge back to the factory default settings. The bridge will request an IP address from the DHCP server (usually the network router). If no DHCP server is found, then the bridge will use its default static IP address, 169.254.1.250, until it detects a DHCP server and is assigned a dynamic IP address.If the bridge is not associated with a router and is using the factory default settings, connect a computer to the bridge using an Ethernet connection to access the web-based utility. You will need to configure the Ethernet connection on the computer with a static IP address and subnet mask.The IP address of your Ethernet adapter should be set to a specific IP address.1. In the IP address field, enter 169.254.x.y (x should be replaced by a number between 1 and 254, and y should be replaced by a number between 0 and 255).2. In the Subnet mask field, enter 255.255.0.0.NOTEThe steps to assign a static IP address to the Ethernet adapter on your computer vary by operating system. For instructions, please refer to the help documentation of your specific operating system. After you have assigned your Ethernet adapter with a static IP address, launch your web browser, and enter the Adapter’s IP address (the default setting is 169.254.1.250)in the Address field. Press Enter.A password request screen appears. (Non-Windows XP users will see a similar screen.) Leave the User name field blank. Enter the password you created during the Setup Wizard. If you did not create a new password, use the default password admin. (You can set a new password from the Administration > Management screen.) Click OK to continue. NOTE If the password request screen does not appear, wait two minutes and try again.Advanced Configuration

7Advanced ConfigurationLinksys WES610N/WET610NSetup > Basic SetupThe first screen that appears is the Basic Setup screen. Use this screen to change the browser-based utility’s language, or to change the bridge’s wired, Ethernet network settings.LanguageLanguage This is used to set the language displayed by the browser-based utility. Select the desired language from the drop-down menu.Network SetupThis section determines if the bridge’s IP address is obtained automatically from a DHCP server, such as your network router (Automatic Configuration - DHCP), or set manually (Static IP).Bridge IP If your network has a DHCP server, such as your network router, assigning IP addresses to your network devices, then keep the default, Automatic Configuration - DHCP. The bridge will request an IP address from the DHCP server (usually the network router). If no DHCP server is found, then the bridge will use its default static IP address, 169.254.1.250, until it detects a DHCP server and is assigned a dynamic IP address.If you want to set a permanent static IP address for the bridge, then select Static IP.If you select Static IP, then complete the following fields: • Static IP Address Enter a unique IP address that will be used to access the browser-based utility. • Subnet Mask Enter the subnet mask of your wired network. • Default Gateway Enter the IP address of the default gateway for your network (in most cases, this is your router).Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.Wireless > Basic Wireless SettingsUse the Basic Wireless Settings screen to configure the bridge’s basic wireless and security settings.There are two ways to configure the bridge’s settings, manual and Wi-Fi Protected Setup. Wi-Fi Protected Setup is a feature that makes it easy to set up your wireless network. If your network router supports Wi-Fi Protected Setup and uses WPA or WPA2 security, then you can use Wi-Fi Protected Setup to automatically connect the bridge.Configuration View To manually configure your wireless network, select Manual. Refer to Basic Wireless Settings, page 8. To use Wi-Fi Protected Setup, select Wi-Fi Protected Setup. Refer to Wi-Fi Protected Setup, page 9.

8Advanced ConfigurationLinksys WES610N/WET610NBasic Wireless SettingsNetwork Name (SSID) The SSID is the network name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any characters on the keyboard). Make sure this setting matches the setting on your wireless router or access point. For added security, you should change the default SSID (linksys) to a unique name.Wireless SecurityThe bridge supports the following wireless security options: WPA Personal, WPA2 Personal, and WEP. WPA (Wi-Fi Protected Access) and WPA2 are stronger security methods than WEP (Wired Equivalent Privacy). For more information about wireless security, refer to “Wireless Security Checklist” on page 4.Security ModeSelect the security method for your wireless network. If you do not want to use wireless security, keep the default, Disabled.NOTERemember that each device in your wireless network MUST use the same security method and passphrase/key, or else the wireless devices will not be able to communicate with each other.WPA PersonalWPA is a security standard stronger than WEP encryption. Encryption WPA supports the TKIP encryption method, with dynamic encryption keys. Passphrase Enter the key shared by the bridge and your wireless router or access point. It must have 8-63 characters.Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.WPA2 PersonalWPA2 is a more advanced, more secure version of WPA. Encryption WPA2 supports two encryption methods, TKIP and AES, with dynamic encryption keys. Select the encryption method, AES or TKIP or AES. The default selection is AES.

9Advanced ConfigurationLinksys WES610N/WET610NPassphrase Enter the key shared by the bridge and wireless router or access point. It must have 8-63 characters.Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.WEPWEP is a basic encryption method, which is not as secure as WPA or WPA2.Encryption Select a level of WEP encryption, 40/64 bits (10 hex digits) or 104/128 bits (26 hex digits). The default is 40/64 bits (10 hex digits).Key 1 Enter the WEP key of your network.Tx Key Key 1 is the transmit key used by the bridge.Authentication The default is Auto, which allows either Open system or Shared key authentication to be used. Select Open to use open system authentication; the sender and recipient do not use a WEP key for authentication. Select Shared to use shared key authentication; the sender and recipient use a WEP key for authentication.Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.Wi-Fi Protected SetupThere are two methods available. Use the method that applies to the router you are using.Method #1Use this method if your router has a Wi-Fi Protected Setup button.1. Click or press the Wi-Fi Protected Setup button on the router.2. Within two minutes, click the Wi-Fi Protected Setup button on the bridge’s Wi-Fi Protected Setup screen.3. After the bridge has been configured, click Close.The Wi-Fi Protected Setup screen displays the Link Status, Network Name (SSID), and Security method.

10Advanced ConfigurationLinksys WES610N/WET610NMethod #2Use this method if your router requests the PIN number of the bridge.1. On the router’s Wi-Fi Protected Setup screen, enter the PIN number on the bridge’s Wi-Fi Protected Setup screen. Then click Register or the appropriate button. (It is also listed on the label on the bottom of the bridge.)2. On the bridge’s Wi-Fi Protected Setup screen, click OK.3. After the bridge has been configured, click Close.The Wi-Fi Protected Setup screen displays the Link Status, Network Name (SSID), and Security method.Wireless > Wireless Network Site SurveyClick the Wireless Network Site Survey tab to begin a site survey. The Wireless Network Site Survey screen lists the wireless networks detected by the bridge.Wireless Network Site SurveyNumber of Wireless Networks The number of wireless networks detected by the bridge is displayed.Select To connect to a wireless network, click Select. Then click Connect.Wireless Network Name The network name or SSID of the wireless network is displayed.GHz The radio band of the wireless network is displayed.Signal The percentage of signal strength is displayed. 100% is the strongest signal strength possible; 0% is the weakest possible.Security If the network supports Wi-Fi Protected Setup, the Wi-Fi Protected Setup icon is displayed. The security method used by the wireless network is displayed.Click Refresh to update the on-screen information.After you have selected a network, click Connect. A new screen appears. Follow the instructions for the security method of your network.WPANetwork Name (SSID) The name of the network you selected is automatically displayed.Security Mode WPA Personal is automatically displayed.Encryption WPA supports the TKIP encryption method, with dynamic encryption keys. Passphrase Enter the key shared by the bridge and wireless router or access point. It must have 8-63 characters.Click Refresh to update the on-screen information.After you have entered the security settings, click Connect.

11Advanced ConfigurationLinksys WES610N/WET610NWPA2Network Name (SSID) The name of the network you selected is automatically displayed.Security Mode WPA2 Personal is automatically displayed.Encryption WPA2 supports two encryption methods, TKIP and AES, with dynamic encryption keys. Select the encryption method, AES or TKIP or AES. Passphrase Enter the key shared by the bridge and wireless router or access point. It must have 8-63 characters.Click Refresh to update the on-screen information.After you have entered the security settings, click Connect.WEPNetwork Name (SSID) The name of the network you selected is automatically displayed.Security Mode WEP is automatically displayed.Encryption Select a level of WEP encryption, 40/64 bits (10 hex digits) or 104/128 bits (26 hex digits).Key 1 Enter the WEP key of your network.Tx Key Key 1 is the transmit key used by the bridge.Authentication The default is Auto, which allows either Open system or Shared key authentication to be used. Select Open to use open system authentication; the sender and recipient do not use a WEP key for authentication. Select Shared to use shared key authentication; the sender and recipient use a WEP key for authentication.Click Refresh to update the on-screen information.After you have entered the security settings, click Connect.Wireless > WMM®Configure the Wireless MultiMedia (WMM) settings. WMM prioritizes packets depending on their respective access mode (traffic type): Background, Best Effort, Video, or Voice. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance.NOTEThe settings on the WMM screen are designed for advanced users only.

12Advanced ConfigurationLinksys WES610N/WET610NWMMAccess ModeYou can assign different settings to the four access modes available. Select the mode you want to configure: Background, Best Effort, Video, or Voice. Follow the instructions for the mode you select. BackgroundUse Aggregation This option defines whether or not the Media Access Control (MAC) layer will set up an Add Block Acknowledgement (ADDBA) session. The default is No. Select Yes to enable this option.Accept Aggregation This option defines whether or not the MAC layer will accept an ADDBA request. The default is Yes. Select No to disable this option.Max. Number of Packets in Aggregation This option defines the maximum number of packets (sub-frames) in the aggregate. The range is 0 to 7. The default is 7.Max. Aggregation Size This option defines the maximum size of the aggregate (in bytes). The range is 0 to 16000. The default is 12000.Timeout Internal This option defines the timeout period in which the aggregate should be closed with a “closing condition” before it is closed by the timer. The range is 0 to 100 ms. The default is 3.Min. Size of Packet in Aggregation This option defines the minimum size (in bytes) of packets to be accumulated in the aggregate. The range is 0 to 1500. The default is 10.ADDBA Timeout This option defines the duration after which the ADDBA setup is terminated, if there are no frame exchanges within this duration by the Block Acknowledgement (ACK) agreement. The range is 0 to 65535 ms. The default is 0, which disables the timeout.Aggregation Window Size This option defines the maximum number of packets transmitted without getting ACKs. The range is 0 to 64. The default is 64.Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.Best EffortUse Aggregation This option defines whether or not the Media Access Control (MAC) layer will set up an Add Block Acknowledgement (ADDBA) session. The default is Yes. Select No to disable this option.Accept Aggregation This option defines whether or not the MAC layer will accept an ADDBA request. The default is Yes. Select No to disable this option.Max. Number of Packets in Aggregation This option defines the maximum number of packets (sub-frames) in the aggregate. The range is 0 to 10. The default is 10.Max. Aggregation Size This option defines the maximum size of the aggregate (in bytes). The range is 0 to 20000. The default is 16000.Timeout Internal This option defines the timeout period in which the aggregate should be closed with a “closing condition” before it is closed by the timer. The range is 0 to 100 ms. The default is 3.Min. Size of Packet in Aggregation This option defines the minimum size (in bytes) of packets to be accumulated in the aggregate. The range is 0 to 1500. The default is 10.ADDBA Timeout This option defines the duration after which the ADDBA setup is terminated, if there are no frame exchanges within this duration by the Block Acknowledgement (ACK) agreement. The range is 0 to 65535 ms. The default is 0, which disables the timeout.Aggregation Window Size This option defines the maximum number of packets transmitted without getting ACKs. The range is 0 to 64. The default is 64.Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.VideoUse Aggregation This option defines whether or not the Media Access Control (MAC) layer will set up an Add Block Acknowledgement (ADDBA) session. The default is Yes. Select No to disable this option.Accept Aggregation This option defines whether or not the MAC layer will accept an ADDBA request. The default is Yes. Select No to disable this option.Max. Number of Packets in Aggregation This option defines the maximum number of packets (sub-frames) in the aggregate. The range is 0 to 7. The default is 7.

13Advanced ConfigurationLinksys WES610N/WET610NMax. Aggregation Size This option defines the maximum size of the aggregate (in bytes). The range is 0 to 16000. The default is 12000.Timeout Internal This option defines the timeout period in which the aggregate should be closed with a “closing condition” before it is closed by the timer. The range is 0 to 100 ms. The default is 3.Min. Size of Packet in Aggregation This option defines the minimum size (in bytes) of packets to be accumulated in the aggregate. The range is 0 to 1500. The default is 10.ADDBA Timeout This option defines the duration after which the ADDBA setup is terminated, if there are no frame exchanges within this duration by the Block Acknowledgement (ACK) agreement. The range is 0 to 65535 ms. The default is 0, which disables the timeout.Aggregation Window Size This option defines the maximum number of packets transmitted without getting ACKs. The range is 0 to 64. The default is 64.Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.VoiceUse Aggregation This option defines whether or not the Media Access Control (MAC) layer will set up an Add Block Acknowledgement (ADDBA) session. The default is Yes. Select No to disable this option.Accept Aggregation This option defines whether or not the MAC layer will accept an ADDBA request. The default is Yes. Select No to disable this option.Max. Number of Packets in Aggregation This option defines the maximum number of packets (sub-frames) in the aggregate. The range is 0 to 2. The default is 2.Max. Aggregation Size This option defines the maximum size of the aggregate (in bytes). The range is 0 to 16000. The default is 10000.Timeout Internal This option defines the timeout period in which the aggregate should be closed with a “closing condition” before it is closed by the timer. The range is 0 to 100 ms. The default is 10.Min. Size of Packet in Aggregation This option defines the minimum size (in bytes) of packets to be accumulated in the aggregate. The range is 0 to 1500. The default is 10.ADDBA Timeout This option defines the duration after which the ADDBA setup is terminated, if there are no frame exchanges within this duration by the Block Acknowledgement (ACK) agreement. The range is 0 to 65535 ms. The default is 0, which disables the timeout.Aggregation Window Size This option defines the maximum number of packets transmitted without getting ACKs. The range is 0 to 64. The default is 64.Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.Wireless > Advanced Wireless SettingsConfigure the bridge’s advanced wireless functions. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance.NOTEThe settings on the Advanced Wireless Settings screen are designed for advanced users only.Advanced WirelessUse LDPC Low-Density Parity-Check Code (LDPC) enables or disables error correction to reduce the probability of data loss in noisy channels. The Rate Adaptation algorithm automatically disabled LDPC coding when working at high PHY rates (higher than 162). To use the LDCP advanced error correction scheme, keep the default, Yes. Otherwise, select No.

14Advanced ConfigurationLinksys WES610N/WET610NERP Protection Type This option configures protection of OFDM packets despite the presence of 802.11b stations within the wireless network. By sending RTS/CTS or CTS2Self packets in 802.11b rates, the bridge informs the wireless network that OFDM packets are going to be transferred and protects the packets in the wireless network. The RTS/CTS and CTS2Self packets create overhead, which may result in lower throughputs. The RTS/CTS option provides better coverage but lower throughputs when compared to CTS2Self, because the RTS/CTS option includes acknowledgement from the receiving device. To use the RTS/CTS option, keep the default, RTS/CTS. The None option may cause collisions between OFDM and CCK packets. To use the None option, select None. To use the CTS2Self option, select CTS2Self.11n Protection Type This option configures protection from non-High Throughput (HT) devices within the wireless network. In case the wireless router (or access point) detects an association of a non-HT legacy device, it will signal all the HT devices to use RTS/CTS or CTS2Self mechanisms before each data transmission. This feature also supports all 802.11n standard protections, including MIMO.The RTS/CTS option provides better coverage but lower throughputs when compared to CTS2Self, because the RTS/CTS option includes acknowledgement from the receiving device. To use the RTS/CTS option, keep the default, RTS/CTS. The None option may cause collisions between HT and legacy packets. To use the None option, select None. To use the CTS2Self option, select CTS2Self.Percentage of maximal transmit power This option sets the percentage of maximal transmit power relative to the regulatory domain restrictions. For example, if the regulatory domain restriction allows transmissions of up to 20 dB, then setting the percentage at 50% allows maximal transmit power of 10 dB. Select the percentage you want to use: 12%, 25%, 50%, or 100%. The default is 100%.QoS Classification Type This option sets 802.1D or 802.1Q mapping from the IP DSCP/TOS field to WMM priorities (Background, Best Effects, Video, Voice). Keep the default, 802.1D, or select 802.1Q, which is used by some IPTV streams.Re-establish Ethernet connection when initiating wireless connection To trigger DHCP discovery from the device that resides behind the bridge, the bridge will reset the Ethernet link between the bridge and the device every time a wireless connection is established. To disable this behavior, select No. Otherwise, keep the default, Yes.Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.Administration > ManagementUse this screen to manage specific bridge functions: access to the web-based utility, backup of the configuration file, and reboot.ManagementBridge AccessUse a password to protect access to the browser-based utility.Bridge Password Enter a new Password for the bridge.Re-enter to confirm Enter the Password again to confirm.Idle Timeout The login times out after a period of inactivity that you specify. The range is 60 to 3600 seconds. The default is 600.Web AccessAccess via Wireless If you are using the bridge in a public domain where you are giving wireless access to your guests, you can disable wireless access to the bridge’s browser-based utility. You will only be able to access the browser-based utility via a wired connection if you disable the setting. Keep the default, Enabled, to allow wireless access to the bridge’s browser-based utility, or select Disabled to block wireless access to the utility.Backup and RestoreBackup To back up the bridge’s configuration file, click Backup Configurations. Then follow the on-screen instructions.

15Advanced ConfigurationLinksys WES610N/WET610NRestore Click Browse and select the configuration file. Then click Restore Configurations.System RebootReboot To reboot or restart the bridge, click Start to Reboot.Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes.Administration > Factory DefaultsUse this screen to restore the bridge’s configuration to its factory default settings. Factory DefaultsRestore All Settings To reset the bridge’s settings to the factory defaults, click Restore All Settings. Any settings you have saved will be lost when the default settings are restored.Administration > Upgrade FirmwareUse this screen to upgrade the bridge’s firmware. Do not upgrade the firmware unless you are experiencing problems with the bridge or the new firmware has a feature you want to use. Before upgrading the firmware, download the bridge’s firmware upgrade file from the Linksys website, www.Linksys.com/support.Upgrade FirmwarePlease select a file to upgrade the firmware Click Browse and select the firmware upgrade file. Then click Start to Upgrade and follow the on-screen instructions.Status > BridgeThe bridge’s current status information is displayed.

16Advanced ConfigurationLinksys WES610N/WET610NBridge InformationFirmware Version The bridge’s current firmware is displayed.Local NetworkLocal MAC Address The bridge’s MAC Address, as seen on your local, Ethernet network, is displayed.IP Address The bridge’s IP Address, as seen on your local, Ethernet network, is displayed.Subnet Mask The Subnet Mask configured for your local network is displayed.Status > WirelessInformation about your wireless network is displayed.WirelessLink Status The status of the connection to your wireless network is displayed.MAC Address The bridge’s MAC Address, as seen on your local, wireless network, is displayed.Network Name (SSID) The wireless network name or SSID is displayed.BSSID The wireless MAC address of the connected wireless router (or access point) is displayed.Radio Band The radio band of your wireless network is displayed.Channel Width The channel width, in MHz, used by your wireless network is displayed.Wide Channel Depending on the channel settings of your network router, the Wide Channel is displayed. If you selected Wide - 40MHz Channel for the router’s Radio Band or Channel Width setting, then this will be your primary Wireless-N channel.Standard Channel The Standard Channel setting is displayed. If you selected Wide – 40MHz Channel for the router’s Radio Band or Channel Width setting, then the Standard Channel will be a secondary channel for Wireless-N.Bit Rate The data transmission rate is displayed.Signal The percentage of signal strength is displayed. 100% is the strongest signal strength possible; 0% is the weakest possible.Security The security method of your wireless network is displayed.

17TroubleshootingLinksys WES610N/WET610N17WES610N/WET610N Your computer or other wired, Ethernet device cannot communicate with the wireless router.1. Access the bridge’s browser-based utility.2. On the Basic Wireless Settings screen, make sure the Network Name (SSID) matches the name of your wireless network.3. Make sure the security settings (WPA, WPA2, or WEP) match the security settings of your wireless network.The bridge’s IP address needs to be changed.If the bridge is connected to a network with a DHCP server (usually the network router), then the bridge will obtain its IP address from the DHCP server. If there is no DHCP server, then the bridge will use its default, static IP address, 169.254.1.250.If you want the bridge to always use a static IP address, then follow these instructions:1. Access the bridge’s browser-based utility.2. Click the Network Setup tab.3. From the Network Connection Type drop-down menu, select Static IP.4. Complete the Static IP Address, Subnet Mask, and Default Gateway fields.5. Click Save Settings.The bridge-enabled computer or other wired, Ethernet device will not communicate with another wireless-enabled device (such as a computer or printer).Check the following: • Make sure the wireless-enabled device is on the same wireless network as the computer or other wired, Ethernet device connected to the bridge. • Make sure that the same Network Name (SSID) is used for all devices on the wireless network. • Make sure all devices are on the same IP network, using compatible IP addresses.The browser-based utility does not accept your password.Check the following: • The password is case-sensitive. Make sure that you are using the correct case(s) when entering the password. • If you forget your password, you can reset the bridge to its factory defaults. Press and hold the bridge’s Reset button for approximately five seconds; the password will be reset to its factory default, admin. All other bridge settings will be reset to the factory defaults as well. (To access the browser-based utility, enter admin in the Password field.)After you make changes through the browser-based utility, the new settings are not displayed on-screen.On your web browser, click Refresh. If the new settings are not displayed, then follow these instructions:1. Unplug the power adapter from the bridge. 2. Wait five seconds, and then plug the power adapter back into the bridge. 3. On your web browser, click Refresh.WEBIf your questions are not addressed here, refer to the Linksys website at Linksys.com/supportTroubleshooting

18SpecificationsLinksys WES610N/WET610N18WES610NModel WES610NStandards IEEE 802.3u, 802.11g, 802.11b, 802.11a, 802.11nLEDs Power, Ethernet, Wi-Fi Protected Setup™, Wireless, individual Ethernet link and activityPorts Ethernet (4), PowerButtons Reset, Wi-Fi Protected SetupCabling Type CAT5eAntennas 3 (internal)Antenna Connector Type N/ADetachable (Yes/No) NoModulations 802.11a: OFDM/BPSK, QPSK, 16-QAM, 64-QAM 802.11b: CCK/QPSK, BPSK 802.11g: OFDM/BPSK, QPSK, 16-QAM, 64-QAM 802.11n: OFDM/BPSK, QPSK, 16-QAM, 64-QAMRF Pwr (EIRP) in dBm 802.11a: 15 dBm (typical) @ 54Mbps 802.11b: 19 dBm (typical) @ 11 Mbps 802.11g: 16 dBm (typical) @ 54 Mbps 802.11n (2.4 GHz): 18 dBm (typical) @ MCS15 802.11n (5 GHz): 16 dBm (typical) @ MCS15Receive Sensitivity 802.11a: -72 dBm (typical) @ 54 Mbps 802.11b: -85 dBm (typical) @ 11 Mbps 802.11g: -73 dBm (typical) @ 54 Mbps 802.11n (20 MHz): -75 dBm (typical) @ MCS15 802.11n (40 MHz): -69 dBm (typical) @ MCS15 Antenna Gain in dBi 1Wireless Security WEP, Wi-Fi Protected Access™ (WPA), Wi-Fi Protected Access™ 2 (WPA2)Security Key Bits Up to 128-bit encryptionEnvironmentalDimensions 6.97” x 5.04” x 2.68” (177 x 128 x 68 mm)Weight 0.65 lb (295 g)Certiﬁcation FCC, UL/cUL, ICES-003, RSS210, CE, Wi-Fi (IEEE 802 11a/b/g/draft n), WPA2™, Wi-Fi Protected Setup, WMM®Power 12V, 1AOperating Temperature 32 to 104ºF (0 to 40ºC)Storage Temperature -4 to 140ºF (-20 to 60ºC)Operating Humidity 10 to 85% NoncondensingStorage Humidity 5 to 90% NoncondensingSpeciﬁcations are subject to change without notice. Specifications

19SpecificationsLinksys WES610N/WET610N19WET610NModel WET610NStandards IEEE 802.3u, 802.11g, 802.11b, 802.11a, 802.11nLEDs Power, Ethernet, Wi-Fi Protected Setup™, WirelessPorts Ethernet, PowerButtons Reset, Wi-Fi Protected SetupCabling Type CAT5eAntennas 3 (internal)Antenna Connector Type N/ADetachable (Yes/No) NoModulations 802.11a: OFDM/BPSK, QPSK, 16-QAM, 64-QAM 802.11b: CCK/QPSK, BPSK 802.11g: OFDM/BPSK, QPSK, 16-QAM, 64-QAM 802.11n: OFDM/BPSK, QPSK, 16-QAM, 64-QAMRF Pwr (EIRP) in dBm 802.11a: 15 dBm (typical) @ 54Mbps 802.11b: 18 dBm (typical) @ 11 Mbps 802.11g: 16 dBm (typical) @ 54 Mbps 802.11n: 12 dBm (typical) @ 130 Mbps (HT20), 270 Mbps (HT40)Receive Sensitivity 802.11a: -72 dBm (typical) @ 54 Mbps 802.11b: -85 dBm (typical) @ 11 Mbps 802.11g: -73 dBm (typical) @ 54 Mbps 802.11n: -70 dBm (typical) @ MCS15/2.4 GHz, -69 dBm (typical) @ MCS15/5.0 GHzAntenna Gain in dBi 1Wireless Security WEP, Wi-Fi Protected Access™ (WPA), Wi-Fi Protected Access™ 2 (WPA2)Security Key Bits Up to 128-bit encryptionEnvironmentalDimensions 5.71” x 4.17” x 2.05” (145 x 106 x 52 mm)Weight 5.61 oz (159 g)Certiﬁcation FCC, UL/cUL, ICES-003, RSS210, CE, Wi-Fi (IEEE 802 11a/b/g/draft n), WPA2™, Wi-Fi Protected Setup, WMM®Power 12V, 1AOperating Temperature 32 to 104ºF (0 to 40ºC)Storage Temperature -4 to 140ºF (-20 to 60ºC)Operating Humidity 10 to 85% NoncondensingStorage Humidity 5 to 90% NoncondensingSpeciﬁcations are subject to change without notice.