LINKSYS WMP300N Wireless-N PCI Adapter User Manual Book

Download:
Mirror Download [FCC.gov]
Document ID	654627
Application ID	nsHV12xnAGL8x9/xxruQ7A==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	225.3kB (2816222 bits)
Date Submitted	2006-05-04 00:00:00
Date Available	2006-05-04 00:00:00
Creation Date	2006-03-31 14:20:55
Producing Software	Acrobat Distiller 6.0.1 (Windows)
Document Lastmod	2006-05-04 14:03:23
Document Title	Book Template.book
Document Creator	FrameMaker 7.0
Document Author:	junelee

2.4 GHz Wireless-N
PCI Adapter
WIRELESS
Model No.
WMP300N
User Guide
Wireless-N PCI Adapter
Copyright and Trademarks
Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2006 Cisco Systems, Inc. All
rights reserved. Other brands and product names are trademarks or registered trademarks of their respective
holders.
WARNING: This product contains chemicals, including lead, known
to the State of California to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
How to Use this User Guide
This User Guide has been designed to make understanding networking with the Wireless-N PCI Adapter easier
than ever. Look for the following items when reading this User Guide:
This checkmark means there is a note of interest and is something you
should pay special attention to while using the Adapter.
This exclamation point means there is a caution or warning and is
something that could damage your property or the Adapter.
This question mark provides you with a reminder about something
you might need to do while using the Adapter.
In addition to these symbols, there are definitions for technical terms that are presented like this:
word: definition.
Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:
Figure 0-1: Sample Figure Description
Figure numbers and descriptions can also be found in the “List of Figures” section.
WMP300N-UG-60331NC JL
Wireless-N PCI Adapter
Table of Contents
Chapter 1: Introduction
Welcome
What’s in this User Guide?
Chapter 2: Planning Your Wireless Network
Network Topology
Roaming
Network Layout
Chapter 3: Getting to Know the Wireless-N PCI Adapter
Overview
The PCI Card
The Antenna Stand
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Starting the Setup
Connecting the Adapter
Setting up the Adapter
Chapter 5: Using the Wireless Network Monitor
Accessing the Wireless Network Monitor
Using the Wireless Network Monitor
Link Information
Connect
Profiles
Creating a New Profile
Appendix A: Troubleshooting
Common Problems and Solutions
Frequently Asked Questions
Appendix B: Windows XP Wireless Zero Configuration
Appendix C: Wireless Security
Security Precautions
Security Threats Facing Wireless Networks
Appendix D: Windows Help
Appendix E: Glossary
18
18
18
18
21
23
24
34
34
34
38
41
41
41
44
45
Wireless-N PCI Adapter
Appendix F: Specifications
Appendix G: Warranty Information
Appendix H: Regulatory Information
Appendix I: Contact Information
50
52
53
59
Wireless-N PCI Adapter
List of Figures
Figure 3-1: Connectors and LED
Figure 3-2: Antenna Stand and Cables
Figure 4-1: Setup Wizard’s Welcome
Figure 4-2: Setup Wizard’s License Agreement
Figure 4-3: Installing the Adapter
Figure 4-4: Available Wireless Networks
Figure 4-5: WEP Key Needed for Connection
Figure 4-6: PSK Needed for Connectio
Figure 4-7: PSK2 Needed for Connectio
Figure 4-8: Congratulations
Figure 4-9: Available Wireless Networks
Figure 4-10: Network Settings
Figure 4-11: Wireless Mode
Figure 4-12: Ad-Hoc Mode Settings
Figure 4-13: Wireless Security
Figure 4-14: Wireless Security - WEP
Figure 4-15: Wireless Security - PSK
Figure 4-16: Wireless Security - PSK2
Figure 4-17: Wireless Security - PSK+RADIUS - EAP-TLS
Figure 4-18: Wireless Security - PSK+RADIUS - PEAP
Figure 4-19: Wireless Security - PSK2+RADIUS - EAP-TLS
Figure 4-20: Wireless Security - PSK2+RADIUS - PEAP
Figure 4-21: Wireless Security - RADIUS - EAP-TLS
Figure 4-22: Wireless Security - RADIUS - PEAP
Figure 4-23: Confirm New Settings
Figure 4-24: Congratulations
Figure 5-1: Wireless Network Monitor Icon
Figure 5-2: Link Information
Figure 5-3: More Information - Wireless Network Status
Figure 5-4: More Information - Wireless Network Statistics
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
19
20
Wireless-N PCI Adapter
Figure 5-5: Connect
Figure 5-6: WEP Key Needed for Connection
Figure 5-7: PSK Needed for Connection
Figure 5-8: PSK2 Needed for Connection
Figure 5-9: Profiles
Figure 5-10: Available Wireless Networks
Figure 5-11: WEP Key Needed for Connection
Figure 5-12: PSK Needed for Connection
Figure 5-13: PSK2 Needed for Connection
Figure 5-14: Congratulations
Figure 5-15: Available Wireless Networks
Figure 5-16: Network Settings
Figure 5-17: Wireless Mode
Figure 5-18: Ad-Hoc Mode Settings
Figure 5-19: Wireless Security
Figure 5-20: Wireless Security - WEP
Figure 5-21: Wireless Security - PSK
Figure 5-22: Wireless Security - PSK2
Figure 5-23: Wireless Security - PSK+RADIUS - EAP-TLS
Figure 5-24: Wireless Security - PSK+RADIUS - PEAP
Figure 5-25: Wireless Security - PSK2+RADIUS - EAP-TLS
Figure 5-26: Wireless Security - PSK2+RADIUS - PEAP
Figure 5-27: Wireless Security - RADIUS - EAP-TLS
Figure 5-28: Wireless Security - RADIUS - PEAP
Figure 5-29: Confirm New Settings
Figure 5-30: Congratulations
Figure B-1: Wireless Network Monitor Icon
Figure B-2: Windows XP - Use Windows XP Wireless Configuration
Figure B-3: Windows XP Wireless Zero Configuration Icon
Figure B-4: Available Wireless Network
Figure B-5: No Wireless Security
Figure B-6: Network Connection - Wireless Security
Figure B-7: Wireless Network Connection
21
21
22
22
23
24
24
25
25
25
26
26
27
27
28
28
29
29
30
30
31
31
32
32
33
33
38
38
38
39
39
40
40
Wireless-N PCI Adapter
Chapter 1: Introduction
Welcome
Thank you for choosing the Wireless-N PCI Adapter. Setting up your network and the Adapter is easier than ever.
How does the Adapter do this? Like all wireless products, the Adapter allows for greater range and mobility
within your wireless network, whether it’s using the Wireless-G (802.11g) or Wireless-B (802.11b) standard. But
with Wireless-N, it has even better range and speed.
adapter: a device that adds network functionality
to your PC.
network: a series of computers or devices
connected for the purpose of data sharing,
storage, and/or transmission between users.
But what does all of this mean?
Networks are useful tools for sharing computer resources. You can access one printer from different computers
and access data located on another computer's hard drive. Networks are even used for playing multiplayer video
games. So, networks are not only useful in homes and offices, they can also be fun.
PCs equipped with wireless cards and adapters can communicate without cumbersome cables. By sharing the
same wireless settings, within their transmission radius, they form a wireless network.
802.11g a wireless networking standard that
specifies a maximum data transfer rate of 54Mbps
and an operating frequency of 2.4GHz.
802.11b: a wireless networking standard that
specifies a maximum data transfer rate of 11Mbps
and an operating frequency of 2.4GHz.
The included Setup Wizard walks you through configuring the Adapter to your wireless network settings, step by
step. Use the instructions in this Guide to help you install and set up the Adapter using the Setup Wizard. These
instructions should be all you need to get the most out of the Adapter.
What’s in this User Guide?
This user guide covers the steps for setting up and using the Wireless-N PCI Adapter.
• Chapter 1: Introduction
This chapter describes the Adapter’s applications and this User Guide.
• Chapter 2: Planning Your Wireless Network
This chapter discusses a few of the basics about wireless networking.
• Chapter 3: Getting to Know the Wireless-N PCI Adapter
This chapter describes the physical features of the Adapter.
• Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
This chapter instructs you on how to install and configure the Adapter.
Chapter 1: Introduction
Welcome
Wireless-N PCI Adapter
• Chapter 5: Using the Wireless Network Monitor
This chapter show you how to use the Adapter’s Wireless Network Monitor.
• Appendix A: Troubleshooting
This appendix describes some problems and solutions, as well as frequently asked questions, regarding
installation and use of the Adapter.
• Appendix B: Windows XP Wireless Zero Configuration
This appendix describes how to use Windows XP Wireless Zero Configuration.
• Appendix C: Wireless Security
This appendix discusses security issues regarding wireless networking and measures you can take to help
protect your wireless network.
• Appendix D: Windows Help
This appendix describes how you can use Windows Help for instructions about networking, such as installing
the TCP/IP protocol.
• Appendix E: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
• Appendix F: Specifications
This appendix provides the Adapter’s technical specifications.
• Appendix G: Warranty Information
This appendix supplies the Adapter’s warranty information.
• Appendix H: Regulatory Information
This appendix supplies the Adapter’s regulatory information.
• Appendix I: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support.
Chapter 1: Introduction
What’s in this User Guide?
Wireless-N PCI Adapter
Chapter 2: Planning Your Wireless Network
Network Topology
A wireless network is a group of computers, each equipped with one wireless adapter. Computers in a wireless
network must be configured to share the same radio channel. Several PCs equipped with wireless cards or
adapters can communicate with one another to form an ad-hoc network.
Linksys wireless adapters also provide users access to a wired network when using an access point or wireless
router. An integrated wireless and wired network is called an infrastructure network. Each wireless PC in an
infrastructure network can talk to any computer in a wired network infrastructure via the access point or wireless
router.
An infrastructure configuration extends the accessibility of a wireless PC to a wired network, and can double the
effective wireless transmission range for two wireless adapter PCs. Since an access point is able to forward data
within a network, the effective transmission range in an infrastructure network can be doubled.
topology: the physical layout of a network.
ad-hoc: a group of wireless devices
communicating directly with each other (peerto-peer) without the use of an access point.
access point: a device that allows wirelessequipped computers and other devices to
communicate with a wired network
infrastructure: a wireless network that is
bridged to a wired network via an access point.
Roaming
Infrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your
wireless PC within your network and the access points will pick up the wireless PC's signal, providing that they
both share the same channel and SSID.
roaming: the ability to take a wireless device
from one access point's range to another without
losing the connection.
ssid: your wireless network's name.
Before enabling you consider roaming, choose a feasible radio channel and optimum access point position.
Proper access point positioning combined with a clear radio signal will greatly enhance performance.
Network Layout
Linksys wireless access points and wireless routers have been designed for use with 802.11a, 802.11b, and
802.11g products. With 802.11g products communicating with the 802.11b standard and some products
incorporating both “a” and “g”, products using these standards can communicate with each other.
Access points and wireless routers are compatible with 802.11a, 802.11b and 802.11g adapters, such as the
notebook adapters for your laptop computers, PCI adapters for your desktop PCs, and USB adapters for when you
want to enjoy USB connectivity. Wireless products will also communicate with the wireless print server.
Chapter 2: Planning Your Wireless Network
Network Topology
Wireless-N PCI Adapter
When you wish to connect your wired network with your wireless network, network ports on access points and
wireless routers can be connected to any of Linksys's switches or routers.
With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at
www.linksys.com for more information about wireless products.
Chapter 2: Planning Your Wireless Network
Network Layout
Wireless-N PCI Adapter
Chapter 3: Getting to Know the Wireless-N PCI Adapter
Overview
The Adapter has two parts, the PCI card and antenna stand.
The PCI Card
The Adapter's connectors attach the antenna stand’s cables to the PCI card of the Adapter.
ANT,
CENTER ANT,
ANT
The antenna connectors are connection points for the PCI card’s antenna cables.
LED
Figure 3-1: Connectors and LED
Green. The LED lights up when the Adapter has an active wireless connection. It flashes when the
Adapter is transmitting or receiving data.
The Antenna Stand
The Adapter’s antenna stand has built-in cables that are color-coded to match the connectors on the PCI card.
Figure 3-2: Antenna Stand and Cables
Chapter 3: Getting to Know the Wireless-N PCI Adapter
Overview
Wireless-N PCI Adapter
Chapter 4: Setting up and Connecting the Wireless-N PCI
Adapter
Starting the Setup
The Wireless-N PCI Adapter Setup Wizard will guide you through the installation procedure. The Setup Wizard will
install the driver and Wireless Network Monitor, as well as connect and configure the Adapter.
IMPORTANT: Do not connect the Adapter until you are instructed to
do so or the setup will not work.
Insert the Setup Wizard CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the
Welcome screen should appear. If it does not, click the Start button and choose Run. In the field that appears,
enter D:\setup.exe (if “D” is the letter of your CD-ROM drive).
On the Welcome screen, you have the following choices:
Figure 4-1: Setup Wizard’s Welcome
Click Here to Start- Click the Click Here to Start button to begin the software installation process.
User Guide - Click the User Guide button to open the PDF file of this User Guide.
Diagnostic - Click the Diagnostic button to run a diagnostic check on your installed Adapter’s Wireless Network
Monitor and driver.
Exit - Click the Exit button to exit the Setup Wizard.
1. To install the Adapter, click the Click Here to Start button on the Welcome screen.
2. After reading the License Agreement, click the Next button if you agree and want to continue the installation,
or click the Cancel button to end the installation.
3. Windows will begin copying the files onto your PC.
Figure 4-2: Setup Wizard’s License Agreement
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Starting the Setup
Wireless-N PCI Adapter
4. The Setup Wizard will now prompt you to install the Adapter into your PC. Click Next and power off your PC.
After installing the Adapter, as shown below, and restarting your PC, the Setup Wizard will continue.
Connecting the Adapter
1. If you haven’t already done so, power off your desktop PC before installing the Adapter.
2. Open your PC case and locate an available PCI slot on the motherboard. Check with your computer
manufacturer for instructions.
3. Slide the Adapter into the PCI slot. Make sure that all of its pins are touching the slot's contacts. You may have
to apply a bit of pressure to slide the Adapter all the way in. After the Adapter is firmly in place, secure its
fastening tab to your PC's chassis with a mounting screw. Then, close your PC.
4. Connect the antenna stand’s cables to the PCI card of the Adapter. Plug the cable with the blue connector into
the blue CENTER ANT port. Then attach the remaining cables to the other ANT ports.
Figure 4-3: Installing the Adapter
NOTE: The antenna cable with the blue connector must plug into the blue CENTER ANT
port. The other antenna cables plug into the rest of the Adapter’s ANT ports.
5. Power on your desktop PC.
Setting up the Adapter
The next screen to appear will be the Available Wireless Networks screen. It provides two options for setting up
the Adapter.
• Available Wireless Networks (for most users). Use this option if you already have a network configured. The
networks available to this Adapter will be listed on-screen. You can choose one of these networks and click
the Connect button to connect to it. Click the Refresh button to update the Available Wireless Network list.
• Advanced Setup. If your network is not listed on this screen, select Advanced Setup to set up the Adapter
manually. This method of setting up the Adapter is intended for advanced users only.
The setup for each option is described, step by step, under the appropriate heading on the following pages.
Click Back to close the Setup Wizard, if you wish to set up the Adapter later.
Figure 4-4: Available Wireless Networks
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Connecting the Adapter
Wireless-N PCI Adapter
Available Wireless Networks
wep (wired equivalent privacy): a method of encrypting network
data transmitted on a wireless network for greater security.
The available networks are listed in the table on the center of the screen by Wireless Network Name. Select the
wireless network you wish to connect to and click the Connect button. (If you do not see your network listed, you
can click the Refresh button to bring the list up again.) If the network uses wireless security, you will need to
configure security on the Adapter. If not, you will be taken directly to the Congratulations screen.
wpa (wi-fi protected access: a wireless security protocol
using TKIP (Temporal Key Integrity Protocol) encryption,
which can be used in conjunction with a RADIUS server.
1. If you have wireless security enabled on your network, continue to step 2. If you don’t have wireless security
enabled, continue to step 3.
encryption: encoding data transmitted in a network.
2. If your network has WEP, PSK, or PSK2 wireless security enabled, then that security
screen will appear. Continue to the section for your wireless security method.
WEP
If you have WEP enabled, this screen will appear. Select 64-bit or 128-bit encryption. Then enter a
passphrase or WEP key.
Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The
passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must match the
passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If
you have any non-Linksys wireless products, enter the WEP key manually on those products.)
WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption,
enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters.
Valid hexadecimal characters are “0” to “9” and “A” to “F”.
Figure 4-5: WEP Key Needed for Connection
Then click Connect and proceed to step 3.
PSK
If your network has the wireless security PSK enabled, this screen will appear.
Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.
Pre-shared Key - Enter a Pre-shared key of 8-63 characters in the Pre-shared Key field.
Then click Connect and proceed to step 3.
Figure 4-6: PSK Needed for Connection
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Setting up the Adapter
Wireless-N PCI Adapter
PSK2
If your network has the wireless security PSK2 enabled, this screen will appear.
Pre-shared Key - Enter a Pre-shared Key of 8-63 characters in the Pre-shared Key field.
Then click Connect and proceed to step 3.
Figure 4-7: PSK2 Needed for Connection
3. After the software has been successfully installed, the Congratulations screen will appear. Click Finish to
exit. For more information about the Wireless Network Monitor, refer to “Chapter 5: Using the Wireless
Network Monitor.”
Congratulations! The installation of the Wireless-N PCI Adapter is complete.
To check the link information, search for available wireless networks, or make additional configuration
changes, proceed to “Chapter 5: Using the Wireless Network Monitor.”
Figure 4-8: Congratulations
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Setting up the Adapter
Wireless-N PCI Adapter
Advanced Setup
If your network is not listed with the available networks, you can use Advanced Setup.
1. Click Advanced Setup on the Available Wireless Network screen to set up the Adapter manually.
Figure 4-9: Available Wireless Networks
2. The Network Settings screen from the Wireless Network Monitor will appear. If your network has a router or
other DHCP server, click the Obtain network settings automatically (DHCP) radio button.
If your network does not have a DHCP server or router, click the Specify network settings radio button.
Enter an IP Address, Subnet Mask, Default Gateway, and DNS addresses appropriate for your network. You
must specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and
DNS addresses, leave these fields empty.
IP Address - This IP Address must be unique to your network.
Subnet Mask - The Adapter’s Subnet Mask must be the same as your wired network’s Subnet Mask.
Default Gateway - Enter the IP address of your network’s Gateway here.
DNS 1 and DNS 2 - Enter the DNS address of your wired Ethernet network here.
Figure 4-10: Network Settings
Click the Next button to continue, or click the Back button to return to the previous screen.
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Setting up the Adapter
10
Wireless-N PCI Adapter
3. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio
button if you want to connect to a wireless router or access point. Click the Ad-Hoc Mode radio button if you
want to connect to another wireless device directly without using a wireless router or access point. Enter the
Wireless Network Name for your network.
Infrastructure Mode - Use this mode if you want to connect to a wireless router or access point.
Ad-Hoc Mode - Use this mode if you want to connect to another wireless device directly without using a
wireless router or access point.
Wireless Network Name- This is the wireless network name (SSID) that must be used for all the devices in
your wireless network. It is case- sensitive and should be a unique name to help prevent others from entering
your network.
Click the Next button to continue, or click the Back button to return to the previous screen.
Figure 4-11: Wireless Mode
4. If you chose Infrastructure Mode, go to step 5 now. If you chose Ad-Hoc Mode, the Ad-Hoc Mode Settings
screen will appear.
Network Mode - Select the Network Mode in which your wireless network will operate. In Mixed mode,
Wireless-N, Wireless-B and Wireless-G devices can operate on the same network. In Wireless-G Only mode,
no Wireless-B devices can operate in the network.
Standard Channel - Select the correct channel for your wireless network. The channel you choose should
match the channel set on the other devices in your wireless network. If you are unsure about which channel
to use, keep the default setting, Auto.
Click the Next button to continue, or click the Back button to return to the previous screen.
Figure 4-12: Ad-Hoc Mode Settings
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Setting up the Adapter
11
Wireless-N PCI Adapter
5. If your wireless network doesn’t have wireless security, select Disabled, and then click the Next button to
continue. Proceed to step 6.
If your wireless network has wireless security, select the method of security used: WEP, PSK, PSK2
PSK+RADIUS, PSK2+RADIUS or RADIUS.
WEP stands for Wired Equivalent Privacy. PSK is a stronger security method than WEP.
PSK2 is a stronger security method than PSK. RADIUS stands for Remote Authentication Dial-In User Service.
Click the Next button to continue or the Back button to return to the previous screen.
Proceed to the appropriate section for your security method: WEP, PSK, PSK2, PSK+RADIUS, PSK2+RADIUS,
or RADIUS.
WEP
WEP - Select 64-bit or 128-bit encryption. Then enter a passphrase or WEP key.
Figure 4-13: Wireless Security
Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. It is casesensitive and should not be longer than 16 alphanumeric characters. This passphrase must match the
passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If
you have any non-Linksys wireless products, enter the WEP key manually on those products.)
WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption,
enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters.
Valid hexadecimal characters are “0” to “9” and “A” to “F”.
Advanced Users
TX Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit
key number 2, 3, or 4, select the appropriate number from the TX Key drop-down box.
Authentication -The default is set to Auto, so it will auto-detect for Shared Key or Open System
authentication. For Shared Key authentication, both the sender and the recipient share a WEP key for
authentication. For Open System authentication, the sender and the recipient do not share a WEP key for
authentication. If you are not sure which authentication method to select, keep the default, Auto.
Click the Next button to continue, or click the Back button to return to the previous screen.
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Setting up the Adapter
Figure 4-14: Wireless Security - WEP
12
Wireless-N PCI Adapter
PSK
PSK offers two encryption methods, TKIP and AES, with dynamic encryption keys. Select TKIP or
AES for encryption. Then enter a Pre-shared Key that is 8-63 characters in length.
Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.
Pre-shared Key - Enter a Pre-shared Key of 8-63 characters in the Pre-shared Key field.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 4-15: Wireless Security - PSK
PSK2
Enter a Pre-shared Key that is 8-63 characters in length.
Pre-shared Key - Enter a Pre-shared Key of 8-63 characters in the Pre-shared Key field.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 4-16: Wireless Security - PSK2
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Setting up the Adapter
13
Wireless-N PCI Adapter
PSK+RADIUS
PSK+RADIUS features PSK security used in coordination with a RADIUS server. (This should only be used
when a RADIUS server is connected to the Router.) PSK+RADIUS offers two authentication methods, EAPTLS and PEAP, as well as two encryption methods, TKIP and AES, with dynamic encryption keys.
Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.
EAP-TLS
If you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the
name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down
menu, select the certificate you have installed to authenticate you on your wireless network. Select the type
of encryption, TKIP or AES, from the Encryption drop-down menu.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 4-17: Wireless Security - PSK+RADIUS EAP-TLS
PEAP
If you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the
password of your wireless network in the Password field. Enter the name of the authentication server in the
Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have
installed to authenticate you on your wireless network; if you want to use any certificate, keep the default
setting, Trust Any. Then select the authentication method used inside the PEAP tunnel. Select the type of
encryption, TKIP or AES, from the Encryption drop-down menu.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 4-18: Wireless Security - PSK+RADIUS - PEAP
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Setting up the Adapter
14
Wireless-N PCI Adapter
PSK2+RADIUS
PSK2+RADIUS Enterprise features PSK2 security used in coordination with a RADIUS server. (This should only be used
when a RADIUS server is connected to the Router.) PSK2+RADIUS offers two authentication methods, EAPTLS and PEAP.
Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.
EAP-TLS
If you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the
name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down
menu, select the certificate you have installed to authenticate you on your wireless network.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 4-19: Wireless Security - PSK2+RADIUS EAP-TLS
PEAP
If you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the
password of your wireless network in the Password field. Enter the name of the authentication server in the
Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have
installed to authenticate you on your wireless network; if you want to use any certificate, keep the default
setting, Trust Any. Then select the authentication method used inside the PEAP tunnel.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 4-20: Wireless Security - PSK2+RADIUS - PEAP
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Setting up the Adapter
15
Wireless-N PCI Adapter
RADIUS
RADIUS features use of a RADIUS server. (This should only be used when a RADIUS server is connected to the
Router.) RADIUS offers two authentication types: EAP-TLS and PEAP.
Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.
EAP-TLS
If you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the
name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down
menu, select the certificate you have installed to authenticate you on your wireless network.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 4-21: Wireless Security - RADIUS - EAP-TLS
PEAP
If you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the
password of your wireless network in the Password field. Enter the name of the authentication server in the
Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have
installed to authenticate you on your wireless network; if you want to use any certificate, keep the default
setting, Trust Any. Then select the authentication method used inside the PEAP tunnel.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 4-22: Wireless Security - RADIUS - PEAP
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Setting up the Adapter
16
Wireless-N PCI Adapter
5. The Confirm New Settings screen will appear next and show the new settings. To save the new settings, click
the Save button. To edit the new settings, click the Back button. To exit the Advanced Setup through the
Wireless Network Monitor, click Exit.
Figure 4-23: Confirm New Settings
6. The Congratulations screen will appear next. Click Connect to Network to implement the new settings and
return to the Link Information screen. Click Return to Profiles to return to the Profiles screen.
Congratulations! Your advanced setup through the Wireless Network Monitor is complete.
To check the link information, search for available wireless networks, or make additional configuration
changes, proceed to “Chapter 5: Using the Wireless Network Monitor.”
Figure 4-24: Congratulations
Chapter 4: Setting up and Connecting the Wireless-N PCI Adapter
Setting up the Adapter
17
Wireless-N PCI Adapter
Chapter 5: Using the Wireless Network Monitor
Use the Wireless Network Monitor to check the link information, search for available wireless networks, or create
profiles that hold different configuration settings.
Accessing the Wireless Network Monitor
After installing the Adapter, the Wireless Network Monitor icon will appear in the system tray of your computer. If
the Wireless Network Monitor is enabled, then the icon will be green. If the Wireless Network Monitor is disabled
or the Adapter is not installed, then the icon will be gray.
Figure 5-1: Wireless Network Monitor
Icon
Using the Wireless Network Monitor
The opening screen of the Wireless Network Monitor is the Link Information screen. From this screen, you can
find out how strong the current wireless signal is and how good the connection’s quality is. You can also click the
More Information button to view additional status information about the current wireless connection. To search
for available wireless networks, click the Connect tab. To perform configuration changes or create connection
profiles, click the Profiles tab.
Link Information
The Link Information screen displays network mode, signal strength, and link quality information about the
current connection. It also provides a button to click for additional status information.
Ad-Hoc Mode or Infrastructure Mode - The screen indicates whether the Adapter is currently working in ad-hoc or
infrastructure mode.
Signal Strength - The Signal Strength bar indicates signal strength.
Link Quality - The Link Quality bar indicates the quality of the wireless network connection.
Click the More Information button to view additional information about the wireless network connection on the
Wireless Network Status screen.
Figure 5-2: Link Information
Chapter 5: Using the Wireless Network Monitor
Accessing the Wireless Network Monitor
18
Wireless-N PCI Adapter
Wireless Network Status
The Wireless Network Status screen provides information on your current network settings.
Radio Band - This shows the radio band used on the network.
Wireless Network Name - This is the unique name (SSID) of the wireless network.
Wireless Mode - The mode of the wireless network currently in use is displayed here.
Wide Channel - This displays the Wireless-N primary channel used with a 40 MHz radio band network.
Standard Channel - This displays the channel used by your wireless network.
Security - The status of the wireless security feature is displayed here.
Authentication - This is your wireless network’s authentication method.
Figure 5-3: More Information - Wireless Network
Status
IP Address - The IP Address of the Adapter is displayed here.
Subnet Mask - The Subnet Mask of the Adapter is shown here.
Default Gateway - The Default Gateway address of the Adapter is displayed here.
DNS1 - This is the DNS address of the Adapter.
MAC Address- The MAC address of the wireless network’s access point or wireless router is shown here.
Signal Strength - The Signal Strength bar indicates the signal strength.
Link Quality - The Link Quality bar indicates the quality of the wireless network connection.
Click the Statistics button to go to the Wireless Network Statistics screen. Click the Back button to return to the
initial Link Information screen. Click the Save to Profile button to save the currently active connection settings to
a profile.
Chapter 5: Using the Wireless Network Monitor
Link Information
19
Wireless-N PCI Adapter
Wireless Network Statistics
The Wireless Networks Statistics screen provides statistics on your current network settings.
Transmit Rate - This is the data transfer rate of the current connection. (In Auto mode, the Adapter dynamically
shifts to the fastest data transfer rate possible at any given time.)
Receive Rate - This is the rate at which data is received.
Packets Received - This shows the packets received by the Adapter, in real time, since connecting to the wireless
network or since the Refresh Statistics button was last pressed.
Packets Transmitted - This shows the packets transmitted from the Adapter, in real time, since connecting to the
wireless network or since the Refresh Statistics button was last pressed.
Bytes Received - This shows the bytes received by the Adapter, in real time, since connecting to the wireless
network or since the Refresh Statistics button was last pressed.
Figure 5-4: More Information - Wireless Network
Statistics
Bytes Transmitted - This shows the bytes transmitted by the Adapter, in real time, since connecting to the
wireless network or since the Refresh Statistics button was last pressed.
Driver Version - This shows the version of the Adapter’s driver.
Noise Level - This shows the level of background noise affecting the wireless signal. A lower reading translates
into a higher quality signal.
Signal Strength - This is the intensity of the wireless signal received by the Adapter.
Transmit Power - This is the power output at which the Adapter is transmitting.
Up Time - This indicates the length of the most recent connection to a wireless network.
Total Up Time - This indicates the cumulative total of the Adapter’s connection time.
Signal Strength - The Signal Strength bar indicates the signal strength.
Link Quality - The Link Quality bar indicates the quality of the wireless network connection.
Click the Back button to return to the initial Link Information screen. Click the Status button to go to the Wireless
Network Status screen. Click the Save to Profile button to save the currently active connection settings to a
profile. Click the Refresh button to reset the statistics.
Chapter 5: Using the Wireless Network Monitor
Link Information
20
Wireless-N PCI Adapter
Connect
The Connect screen displays a list of available networks in the table on the left. The table shows each network’s
Wireless Network Name, Channel, and the quality of the wireless signal the Adapter is receiving. You may click
Wireless Network Name, CH (Channel), or Signal, to sort by that field.
Wireless Network Name - The SSID or unique name of the wireless network is displayed here.
CH - This is the channel that the network uses.
Signal - This is the percentage of signal strength, from 0 to 100%.
Site Information
For each network selected, the following settings are listed:
Figure 5-5: Connect
Wireless Mode - This is the mode of the wireless network currently in use.
Network Type- This is the network type used by your wireless network.
Radio Band - This is the radio band used by your wireless network.
Security - The status of the wireless security feature is displayed here.
wep (wired equivalent privacy): a method of encrypting network
data transmitted on a wireless network for greater security.
MAC Address- The MAC address of the wireless network’s access point is displayed here.
wpa (wi-fi protected access: a wireless security protocol
using TKIP (Temporal Key Integrity Protocol) encryption,
which can be used in conjunction with a RADIUS server.
Refresh - Click the Refresh button to perform a new search for wireless devices.
encryption: encoding data transmitted in a network.
Connect - To connect to one of the networks on the list, select the wireless network, and click the Connect
button. If the network has security enabled, then you will see a new screen appear.
• WEP Key Needed for Connection
If the network has the wireless security WEP encryption enabled, then you will see the WEP Key Needed for
Connection screen. Select the appropriate level of WEP encryption, 64-bit or 128-bit. Then enter the
network’s Passphrase or WEP Key. To connect to the network, click the Connect button. To cancel the
connection, click the Cancel button.
Figure 5-6: WEP Key Needed for Connection
Chapter 5: Using the Wireless Network Monitor
Connect
21
Wireless-N PCI Adapter
• PSK Needed for Connection
If the network has the wireless security PSK enabled, then you will see the PSK Needed
for Connection screen. Select the appropriate encryption type, TKIP or AES. Enter the network’s Pre-shared
Key in the Pre-shared Key field. To connect to the network, click the Connect button. To cancel the
connection, click the Cancel button.
Figure 5-7: PSK Needed for
Connection
• PSK2 Needed for Connection
If the network has the wireless security PSK2 enabled, then you will see the PSK2 Needed
for Connection screen. Enter the network’s Pre-shared Key in the Pre-shared Key field. To connect to the
network, click the Connect button. To cancel the connection, click the Cancel button.
Figure 5-8: PSK2 Needed for
Connection
Chapter 5: Using the Wireless Network Monitor
Connect
22
Wireless-N PCI Adapter
Profiles
The Profiles screen lets you save different configuration profiles for different network setups. The table on the left
displays a list of available profiles with their profile names and Wireless Network Names.
Profile - The name of the profile is displayed here.
Wireless Network Name - The SSID or unique name of the wireless network is displayed here.
Site Information
For each profile selected, the following are listed:
Wireless Mode - This is the mode of the wireless network currently in use.
Wide Channel - This displays the Wireless-N primary channel used with a 40 MHz radio band network.
Figure 5-9: Profiles
Standard Channel - This displays the channel used by your wireless network.
Security - The status of the wireless security feature is displayed here.
Authentication - The authentication setting for the network is shown here.
Connect - To connect to a wireless network using a specific profile, select the profile, and click Connect.
New - Click the New button to create a new profile. See the next section, “Creating a New Profile,” for detailed
instructions.
Edit - Select the profile you want to change, and then click the Edit button.
Import - Click the Import button to import a profile that has been saved in another location. Select the
appropriate file, and click the Open button.
Export - Select the profile you want to save in a different location, and click the Export button. Direct Windows to
the appropriate folder, and click the Save button.
NOTE: If you want to export more than one
profile, you have to export them one at a time.
Delete - Select the profile you want to delete, and then click the Delete button.
Chapter 5: Using the Wireless Network Monitor
Profiles
23
Wireless-N PCI Adapter
Creating a New Profile
The next screen to appear will be the Available Wireless Networks screen. It provides two options for setting up
the Adapter.
• Available Wireless Networks (for most users). Use this option if you already have a network configured. The
networks available to this Adapter will be listed on-screen. You can choose one of these networks and click
the Connect button to connect to it. Click the Refresh button to update the Available Wireless Network list.
• Advanced Setup. If your network is not listed on this screen, select Advanced Setup to set up the Adapter
manually. This method of setting up the Adapter is intended for advanced users only.
The setup for each option is described, step by step, under the appropriate heading on the following pages.
Click Back to close the Setup Wizard, if you wish to set up the Adapter later.
Figure 5-10: Available Wireless Networks
Available Wireless Networks
The available networks are listed in the table on the center of the screen by Wireless Network Name. Select the
wireless network you wish to connect to and click the Connect button. (If you do not see your network listed, you
can click the Refresh button to bring the list up again.) If the network uses wireless security, you will need to
configure security on the Adapter. If not, you will be taken directly to the Congratulations screen.
1. If you have wireless security enabled on your network, continue to step 2. If you don’t have wireless security
enabled, continue to step 3.
2. If your network has WEP, PSK, or PSK2 wireless security enabled, then that security
screen will appear. Continue to the section for your wireless security method.
WEP
If you have WEP enabled, this screen will appear. Select 64-bit or 128-bit encryption. Then enter a
passphrase or WEP key.
Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The
passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must match the
passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If
you have any non-Linksys wireless products, enter the WEP key manually on those products.)
Figure 5-11: WEP Key Needed for Connection
Chapter 5: Using the Wireless Network Monitor
Creating a New Profile
24
Wireless-N PCI Adapter
WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption,
enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters.
Valid hexadecimal characters are “0” to “9” and “A” to “F”.
Then click Connect and proceed to step 3.
PSK
If your network has the wireless security PSK enabled, this screen will appear.
Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.
Pre-shared Key - Enter a Pre-shared key of 8-63 characters in the Pre-shared Key field.
Figure 5-12: PSK Needed for
Connection
Then click Connect and proceed to step 3.
PSK2
If your network has the wireless security PSK2 enabled, this screen will appear.
Pre-shared Key - Enter a Pre-shared Key of 8-63 characters in the Pre-shared Key field.
Then click Connect and proceed to step 3.
3. After the software has been successfully installed, the Congratulations screen will appear. Click Finish to
return to the Link Information screen.
Congratulations! The profile has been successfully configured.
Figure 5-13: PSK2 Needed for
Connection
Figure 5-14: Congratulations
Chapter 5: Using the Wireless Network Monitor
Creating a New Profile
25
Wireless-N PCI Adapter
Advanced Setup
If your network is not listed with the available networks, you can use Advanced Setup.
1. Click Advanced Setup on the Available Wireless Network screen to set up the Adapter manually.
Figure 5-15: Available Wireless Networks
2. The Network Settings screen from the Wireless Network Monitor will appear. If your network has a router or
other DHCP server, click the Obtain network settings automatically (DHCP) radio button.
If your network does not have a DHCP server or router, click the Specify network settings radio button.
Enter an IP Address, Subnet Mask, Default Gateway, and DNS addresses appropriate for your network. You
must specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and
DNS addresses, leave these fields empty.
IP Address - This IP Address must be unique to your network.
Subnet Mask - The Adapter’s Subnet Mask must be the same as your wired network’s Subnet Mask.
Default Gateway - Enter the IP address of your network’s Gateway here.
DNS 1 and DNS 2 - Enter the DNS address of your wired Ethernet network here.
Figure 5-16: Network Settings
Click the Next button to continue, or click the Back button to return to the previous screen.
Chapter 5: Using the Wireless Network Monitor
Creating a New Profile
26
Wireless-N PCI Adapter
3. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio
button if you want to connect to a wireless router or access point. Click the Ad-Hoc Mode radio button if you
want to connect to another wireless device directly without using a wireless router or access point. Enter the
Wireless Network Name for your network.
Infrastructure Mode - Use this mode if you want to connect to a wireless router or access point.
Ad-Hoc Mode - Use this mode if you want to connect to another wireless device directly without using a
wireless router or access point.
Wireless Network Name- This is the wireless network name (SSID) that must be used for all the devices in
your wireless network. It is case- sensitive and should be a unique name to help prevent others from entering
your network.
Click the Next button to continue, or click the Back button to return to the previous screen.
Figure 5-17: Wireless Mode
4. If you chose Infrastructure Mode, go to step 5 now. If you chose Ad-Hoc Mode, the Ad-Hoc Mode Settings
screen will appear.
Network Mode - Select the Network Mode in which your wireless network will operate. In Mixed mode,
Wireless-N, Wireless-B and Wireless-G devices can operate on the same network. In Wireless-G Only mode,
no Wireless-B devices can operate in the network.
Standard Channel - Select the correct channel for your wireless network. The channel you choose should
match the channel set on the other devices in your wireless network. If you are unsure about which channel
to use, keep the default setting, Auto.
Click the Next button to continue, or click the Back button to return to the previous screen.
Figure 5-18: Ad-Hoc Mode Settings
Chapter 5: Using the Wireless Network Monitor
Creating a New Profile
27
Wireless-N PCI Adapter
1. If your wireless network doesn’t have wireless security, select Disabled, and then click the Next button to
continue. Proceed to step 6.
If your wireless network has wireless security, select the method of security used: WEP, PSK, PSK2
PSK-RADIUS, PSK2-RADIUS, or RADIUS.
WEP stands for Wired Equivalent Privacy. PSK is a stronger security method than WEP.
PSK2 is a stronger security method than PSK. RADIUS stands for Remote Authentication Dial-In User Service.
Click the Next button to continue or the Back button to return to the previous screen.
Proceed to the appropriate section for your security method: WEP, PSK, PSK2, PSK+RADIUS
PSK2+RADIUS , or RADIUS.
WEP
WEP - Select 64-bit or 128-bit encryption. Then enter a passphrase or WEP key.
Figure 5-19: Wireless Security
Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. It is casesensitive and should not be longer than 16 alphanumeric characters. This passphrase must match the
passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If
you have any non-Linksys wireless products, enter the WEP key manually on those products.)
WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption,
enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters.
Valid hexadecimal characters are “0” to “9” and “A” to “F”.
Advanced Users
TX Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit
key number 2, 3, or 4, select the appropriate number from the TX Key drop-down box.
Authentication -The default is set to Auto, so it will auto-detect for Shared Key or Open System
authentication. For Shared Key authentication, both the sender and the recipient share a WEP key for
authentication. For Open System authentication, the sender and the recipient do not share a WEP key for
authentication. If you are not sure which authentication method to select, keep the default, Auto.
Click the Next button to continue, or click the Back button to return to the previous screen.
Chapter 5: Using the Wireless Network Monitor
Creating a New Profile
Figure 5-20: Wireless Security - WEP
28
Wireless-N PCI Adapter
PSK
PSK offers two encryption methods, TKIP and AES, with dynamic encryption keys. Select TKIP or
AES for encryption. Then enter a Pre-shared Key that is 8-63 characters in length.
Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.
Pre-shared Key - Enter a Pre-shared Key of 8-63 characters in the Pre-shared Key field.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 5-21: Wireless Security - PSK
PSK2
Enter a Pre-shared Key that is 8-63 characters in length.
Pre-shared Key - Enter a Pre-shared Key of 8-63 characters in the Pre-shared Key field.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 5-22: Wireless Security - PSK2
Chapter 5: Using the Wireless Network Monitor
Creating a New Profile
29
Wireless-N PCI Adapter
PSK+RADIUS
PSK+RADIUS features PSK security used in coordination with a RADIUS server. (This should only be used
when a RADIUS server is connected to the Router.) PSK+RADIUS offers two authentication methods, EAPTLS and PEAP, as well as two encryption methods, TKIP and AES, with dynamic encryption keys.
Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.
EAP-TLS
If you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the
name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down
menu, select the certificate you have installed to authenticate you on your wireless network. Select the type
of encryption, TKIP or AES, from the Encryption drop-down menu.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 5-23: Wireless Security - PSK+RADIUS EAP-TLS
PEAP
If you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the
password of your wireless network in the Password field. Enter the name of the authentication server in the
Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have
installed to authenticate you on your wireless network; if you want to use any certificate, keep the default
setting, Trust Any. Then select the authentication method used inside the PEAP tunnel. Select the type of
encryption, TKIP or AES, from the Encryption drop-down menu.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 5-24: Wireless Security - PSK+RADIUS PEAP
Chapter 5: Using the Wireless Network Monitor
Creating a New Profile
30
Wireless-N PCI Adapter
PSK2+RADIUS
PSK2+RADIUS features PSK2 security used in coordination with a RADIUS server. (This should only be used
when a RADIUS server is connected to the Router.) PSK2+RADIUS offers two authentication methods, EAPTLS and PEAP.
Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.
EAP-TLS
If you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the
name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down
menu, select the certificate you have installed to authenticate you on your wireless network.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 5-25: Wireless Security - PSK2+RADIUS EAP-TLS
PEAP
If you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the
password of your wireless network in the Password field. Enter the name of the authentication server in the
Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have
installed to authenticate you on your wireless network; if you want to use any certificate, keep the default
setting, Trust Any. Then select the authentication method used inside the PEAP tunnel.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 5-26: Wireless Security - PSK2+RADIUS PEAP
Chapter 5: Using the Wireless Network Monitor
Creating a New Profile
31
Wireless-N PCI Adapter
RADIUS
RADIUS features use of a RADIUS server. (This should only be used when a RADIUS server is connected to the
Router.) RADIUS offers two authentication types: EAP-TLS and PEAP.
Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.
EAP-TLS
If you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the
name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down
menu, select the certificate you have installed to authenticate you on your wireless network.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 5-27: Wireless Security - RADIUS - EAP-TLS
PEAP
If you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the
password of your wireless network in the Password field. Enter the name of the authentication server in the
Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have
installed to authenticate you on your wireless network; if you want to use any certificate, keep the default
setting, Trust Any. Then select the authentication method used inside the PEAP tunnel.
Click the Next button to continue or the Back button to return to the previous screen.
Figure 5-28: Wireless Security - RADIUS - PEAP
Chapter 5: Using the Wireless Network Monitor
Creating a New Profile
32
Wireless-N PCI Adapter
5. The Confirm New Settings screen will appear next and show the new settings. To save the new settings, click
the Save button. To edit the new settings, click the Back button. To exit the Advanced Setup through the
Wireless Network Monitor, click Exit.
Figure 5-29: Confirm New Settings
6. The Congratulations screen will appear next. Click Connect to Network to implement the new settings and
return to the Link Information screen. Click Return to Profiles to return to the Profiles screen.
Congratulations! The profile has been successfully configured.
Figure 5-30: Congratulations
Chapter 5: Using the Wireless Network Monitor
Creating a New Profile
33
Wireless-N PCI Adapter
Appendix A: Troubleshooting
This appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.” This
appendix provides solutions to problems that may occur during the installation and operation of the Wireless-N
PCI Adapter. Read the description below to solve your problems. If you can't find an answer here, check the
Linksys website at www.linksys.com.
Common Problems and Solutions
1. The Wireless-N PCI Adapter does not work properly.
• Power off the PC and remove the Adapter. Then reinstall the Adapter.
• Make sure you have installed the proper driver.
If the Adapter does not function after attempting the above steps, remove it and do the following:
• Uninstall the driver software from your PC.
• Run the Setup Wizard again to re-install the driver and software.
2. I cannot communicate with other computers linked via Ethernet in the Infrastructure configuration.
Make sure that the Adapter is configured with the same wireless network name (SSID) and security options
as the other computers in the Infrastructure configuration.
Frequently Asked Questions
Can I run an application from a remote computer over the wireless network?
This will depend on whether or not the application is designed to be used over a network. Consult the
application’s user guide to determine if it supports operation over a network.
Can I play computer games with other members of the wireless network?
Yes, as long as the game supports multiple players over a LAN (local area network). Refer to the game’s user
guide for more information.
What is the 802.11b standard?
It is one of the standards for wireless networks. The 802.11b standard allows wireless networking hardware from
different manufacturers to communicate, provided that the hardware complies with the 802.11b standard. The
802.11b standard states a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.
Appendix A: Troubleshooting
Common Problems and Solutions
34
Wireless-N PCI Adapter
What is the IEEE 802.11g standard?
It is one of the IEEE standards for wireless networks. The 802.11g standard allows wireless networking hardware
from different manufacturers to communicate, provided that the hardware complies with the 802.11g standard.
The 802.11g standard states a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz.
What 802.11b features are supported?
The product supports the following 802.11b functions:
• CSMA/CA plus Acknowledge protocol
• Multi-Channel Roaming
• Automatic Rate Selection
• RTS/CTS feature
• Fragmentation
• Power Management
What IEEE 802.11g features are supported?
The product supports the following IEEE 802.11g functions:
• CSMA/CA plus Acknowledge protocol
• OFDM protocol
• Multi-Channel Roaming
• Automatic Rate Selection
• RTS/CTS feature
• Fragmentation
• Power Management
What is ad-hoc mode?
When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to
communicate directly with each other. This type of network will not communicate with any wired network.
What is infrastructure mode?
When a wireless network is set to infrastructure mode, the wireless network is configured to communicate with a
wired network through a wireless access point.
What is roaming?
Roaming is the ability of a portable computer user to communicate continuously while moving freely throughout
an area greater than that covered by a single access point. Before using the roaming function, the workstation
must make sure that it is the same channel number with the access point of dedicated coverage area.
To achieve true seamless connectivity, the wireless LAN must incorporate a number of different functions. Each
node and access point, for example, must always acknowledge receipt of each message. Each node must
maintain contact with the wireless network even when not actually transmitting data. Achieving these functions
Appendix A: Troubleshooting
Frequently Asked Questions
35
Wireless-N PCI Adapter
simultaneously requires a dynamic RF networking technology that links access points and nodes. In such a
system, the user’s end node undertakes a search for the best possible access to the system. First, it evaluates
such factors as signal strength and quality, as well as the message load currently being carried by each access
point and the distance of each access point to the wired backbone. Based on that information, the node next
selects the right access point and registers its address. Communications between end node and host computer
can then be transmitted up and down the backbone.
As the user moves on, the end node’s RF transmitter regularly checks the system to determine whether it is in
touch with the original access point or whether it should seek a new one. When a node no longer receives
acknowledgment from its original access point, it undertakes a new search. Upon finding a new access point, it
then re-registers, and the communication process continues.
What is ISM band?
The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM
(Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available
worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in
the hands of users around the globe.
What is Spread Spectrum?
Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in
reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for
reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband
transmission, but the trade-off produces a signal that is, in effect, louder and thus easier to detect, provided that
the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to
the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives,
Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS).
What is DSSS? What is FHSS? And what are their differences?
Frequency-Hopping Spread-Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that
is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical
channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-Sequence SpreadSpectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip
(or chipping code). The longer the chip, the greater the probability that the original data can be recovered. Even if
one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can
recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low
power wideband noise and is rejected (ignored) by most narrowband receivers.
What is WEP?
WEP is Wired Equivalent Privacy, a data privacy mechanism based on a shared key algorithm, as described in the
802.11 standard.
Appendix A: Troubleshooting
Frequently Asked Questions
36
Wireless-N PCI Adapter
What is WPA?
WPA is Wi-Fi Protected Access, a wireless security protocol that can be used in conjunction with a RADIUS server.
What is RADIUS?
RADIUS is Remote Authentication Dial-In User Service, which uses an authentication server to control network
access.
Appendix A: Troubleshooting
Frequently Asked Questions
37
Wireless-N PCI Adapter
Appendix B: Windows XP Wireless Zero Configuration
If your computer is running Windows XP, then this choice will be available. If you want to use Windows XP
Wireless Zero Configuration to control the Adapter, instead of using the Wireless Network Monitor, then right-click
the Wireless Network Monitor and select Use Windows XP Wireless Configuration.
If you want to switch back to the Wireless Network Monitor, right-click the Wireless Network Monitor icon, and
select Use Linksys Wireless Network Monitor.
Figure B-1: Wireless Network Monitor Icon
Figure B-2: Windows XP - Use Windows XP
Wireless Configuration
1. After installing the Adapter, the Windows XP Wireless Zero Configuration icon will appear in your computer’s
system tray. Double-click the icon.
NOTE: For more information about Wireless Zero Configuration, refer to Windows Help.
Figure B-3: Windows XP Wireless Zero Configuration Icon
Appendix B: Windows XP Wireless Zero Configuration
38
Wireless-N PCI Adapter
2. The screen that appears will show any available wireless network. Select the network you want. Click the
Connect button.
NOTE: Steps 2 and 3 are the instructions and
screenshots for Windows XP with Service Pack 2
installed.
If your network does not have wireless security enabled, go to step 3.
If your network does have wireless security enabled, go to step 4.
Figure B-4: Available Wireless Network
3. If your network does not have wireless security enabled, click the Connect Anyway button to connect the
Adapter to your network.
Figure B-5: No Wireless Security
Appendix B: Windows XP Wireless Zero Configuration
39
Wireless-N PCI Adapter
4. If your network uses wireless security WEP, enter the WEP Key used in the Network Key and Confirm
network key fields. If your network uses wireless security WPA Personal, enter the Passphrase used in the
Network Key and Confirm network key fields. Click the Connect button.
Figure B-6: Network Connection - Wireless Security
NOTE: Windows XP Wireless Zero Configuration
does not support the use of a passphrase. Enter
the exact WEP key used by your access point.
5. Your wireless network will appear as Connected when your connection is active.
For more information about wireless networking on a Windows XP computer, click the Start button, select Help,
and choose Support. Enter the keyword wireless in the field provided, and press the Enter key.
The setup of Windows XP Wireless Configuration is complete.
Figure B-7: Wireless Network Connection
Appendix B: Windows XP Wireless Zero Configuration
40
Wireless-N PCI Adapter
Appendix C: Wireless Security
Linksys wants to make wireless networking as safe and easy for you as possible. The current generation of
Linksys products provide several network security features, but they require specific action on your part for
implementation. So, keep the following in mind whenever you are setting up or using your wireless network.
Security Precautions
The following is a complete list of security precautions to take (at least steps 1 through 5 should be followed):
1. Change the default SSID.
2. Disable SSID Broadcast.
3. Change the default password for the Administrator account.
4. Enable MAC Address Filtering.
5. Change the SSID periodically.
6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce
your network performance.
NOTE: Note: Some of these security features are
available only through the network router or
access point. Refer to the router or access point’s
documentation for more information.
7. Change the WEP encryption keys periodically.
Security Threats Facing Wireless Networks
Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking
products first listen for “beacon messages”. These messages can be easily decrypted and contain much of the
network’s information, such as the network’s SSID (Service Set Identifier). Here are the steps you can take:
Change the administrator’s password regularly. With every wireless networking device you use, keep in mind
that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the only
person who can change network settings. If a hacker gets a hold of the administrator’s password, he, too, can
change those settings. So, make it harder for a hacker to get that information. Change the administrator’s
password regularly.
Appendix C: Wireless Security
Security Precautions
41
Wireless-N PCI Adapter
SSID. There are several things to keep in mind about the SSID:
1. Disable Broadcast
2. Make it unique
3. Change it often
Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be
more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast
the SSID.
Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.)
Hackers know these defaults and can check these against your network. Change your SSID to something unique
and not something related to your company or the networking products you use.
Change your SSID regularly so that any hackers who have gained access to your wireless network will have to
start from the beginning in trying to break in.
MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only
those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with
a random MAC Address.
WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security
concerns. This is overstating WEP’s ability. Again, this can only provide enough security to make a hacker’s job
more difficult.
There are several ways that WEP can be maximized:
1. Use the highest level of encryption possible
2. Use “Shared Key” authentication
IMPORTANT: Always remember that each device
in your wireless network MUST use the same
encryption method and encryption key or your
wireless network will not function properly.
3. Change your WEP key regularly
WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. WPA2 is the
newer version of Wi-Fi Protected Access with stronger encryption than WPA. WPA gives you a choice of two
encryption methods: TKIP (Temporal Key Integrity Protocol), which incorporates Message Integrity Code (MIC) to
provide protection against hackers, and AES (Advanced Encryption System), which utilizes a symmetric 128-Bit
block data encryption. WPA2 uses AES encryption. (AES is stronger than TKIP.)
Appendix C: Wireless Security
Security Threats Facing Wireless Networks
42
Wireless-N PCI Adapter
WPA-Enterprise and WPA2-Enterprise use WPA/WPA2 security and a RADIUS (Remote Authentication Dial-In User
Service) server for authentication. RADIUS uses a RADIUS server.
WPA/WPA2-Personal. Select the type of algorithm, TKIP or AES (AES is automatically selected for WPA2Personal), and enter a password in the Pre-shared Key field of 8-63 characters.
WPA/WPA2-Enterprise. This method is WPA or WPA2 used in coordination with a RADIUS server. Select the
authentication method, EAP-TLS or PEAP. Then configure the appropriate settings for your authentication
method.
RADIUS. This method features use of a RADIUS server. Select the authentication method, EAP-TLS or PEAP.
Then configure the appropriate settings for your authentication method.
Implementing encryption may have a negative impact on your network’s performance, but if you are transmitting
sensitive data over your network, encryption should be used.
These security recommendations should help keep your mind at ease while you are enjoying the most flexible
and convenient technology Linksys has to offer.
Appendix C: Wireless Security
Security Threats Facing Wireless Networks
43
Wireless-N PCI Adapter
Appendix D: Windows Help
Almost all wireless products require Microsoft Windows. Windows is the most used operating system in the world
and comes with many features that help make networking easier. These features can be accessed through
Windows Help and are described in this appendix.
TCP/IP
Before a computer can communicate with an access point or wireless router, TCP/IP must be enabled. TCP/IP is a
set of instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless networks
as well. Your PCs will not be able to utilize wireless networking without having TCP/IP enabled. Windows Help
provides complete instructions on enabling TCP/IP.
Shared Resources
If you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on
utilizing shared resources.
Network Neighborhood/My Network Places
Other PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the
version of Windows you're running). Windows Help provides complete instructions on adding PCs to your
network.
Appendix D: Windows Help
44
Wireless-N PCI Adapter
Appendix E: Glossary
This glossary contains some basic networking terms you may come across when using this product. For more
advanced terms, see the complete Linksys glossary at http://www.linksys.com/glossary.
Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired
network. Also used to expand the range of a wireless network.
Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of an
access point.
AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption.
Bandwidth - The transmission capacity of a given device or network.
Bit - A binary digit.
Boot - To start a device and cause it to start executing instructions.
Broadband - An always-on, fast Internet connection.
Browser - An application program that provides a way to look at and interact with all the information on the World
Wide Web.
Byte - A unit of data that is usually eight bits long
Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the
Internet.
Daisy Chain - A method used to connect devices in a series, one after the other.
DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a fixed
domain name (e.g., www.xyz.com) and a dynamic IP address.
Default Gateway - A device that forwards Internet traffic from your local area network.
DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign
temporary IP addresses to network computers by “leasing” an IP address to a user for a limited amount of time,
instead of assigning permanent IP addresses.
Appendix E: Glossary
45
Wireless-N PCI Adapter
DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be “seen” from
the Internet.
DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP
addresses.
Domain - A specific name for a network of computers.
Download - To receive a file transmitted over a network.
DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines.
Dynamic IP Address - A temporary IP address assigned by a DHCP server.
EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access.
Many specific authentication methods work within this framework.
Encryption - Encoding data transmitted in a network.
Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common
transmission medium.
Firewall - A set of related programs located at a network gateway server that protects the resources of a network
from users from other networks.
Firmware - The programming code that runs a networking device.
FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network.
Full Duplex - The ability of a networking device to receive and transmit data simultaneously.
Gateway - A device that interconnects networks with different, incompatible communications protocols.
Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a
time.
HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World Wide
Web.
Infrastructure - A wireless network that is bridged to a wired network via an access point.
IP (Internet Protocol) - A protocol used to send data over a network.
Appendix E: Glossary
46
Wireless-N PCI Adapter
IP Address - The address used to identify a computer or device on a network.
IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device.
IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer.
ISP (Internet Service Provider) - A company that provides access to the Internet.
LAN - The computers and networking products that make up your local network.
MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking
device.
Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.
NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different
IP address for the Internet.
Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or
transmission between users.
Packet - A unit of data sent over a network.
Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically
generating the WEP encryption keys for Linksys products.
Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.
POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet.
Port - The connection point on a computer or networking device used for plugging in cables or adapters.
Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power.
PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication
(username and password) in addition to data transport.
PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be
tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe.
RADIUS (Remote Authentication Dial-In User Service) - A protocol that uses an authentication server to control
network access.
Appendix E: Glossary
47
Wireless-N PCI Adapter
RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires.
Roaming - The ability to take a wireless device from one access point's range to another without losing the
connection.
Router - A networking device that connects multiple networks together.
Server - Any computer whose function in a network is to provide user access to files, printing, communications,
and other services.
SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet.
SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol.
SPI (Stateful Packet Inspection) Firewall - A technology that inspects incoming packets of information before
allowing them to enter the network.
SSID (Service Set IDentifier) - Your wireless network's name.
Static IP Address - A fixed address assigned to a computer or device that is connected to a network.
Static Routing - Forwarding data in a network via a fixed path.
Subnet Mask - An address code that determines the size of the network.
Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of devices
to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an electrical
circuit.
TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement
from the recipient of data sent.
TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a
network.
Telnet - A user command and TCP/IP protocol used for accessing remote PCs.
TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password
capability.
Throughput - The amount of data moved successfully from one node to another in a given time period.
Appendix E: Glossary
48
Wireless-N PCI Adapter
TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for
each packet transmitted.
Topology - The physical layout of a network.
TX Rate - Transmission Rate.
Upgrade - To replace existing software or firmware with a newer version.
Upload - To transmit a file over a network.
URL (Uniform Resource Locator) - The address of a file located on the Internet.
VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another
over the Internet.
WAN (Wide Area Network)- The Internet.
WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for
greater security.
WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with each
other wirelessly.
WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key Integrity Protocol)
encryption, which can be used in conjunction with a RADIUS server.
Appendix E: Glossary
49
Wireless-N PCI Adapter
Appendix F: Specifications
Model
WMP300N
Standards
IEEE 802.11b, IEEE 802.11g, draft IEEE 802.11n
Channels
802.11b/802.11g/Wireless-N (20MHz)
11 Channels (USA, Canada)
13 Channels (Europe)
LEDs
ACT
Protocols
802.11b: CCK, QPSK, BPSK
802.11g: OFDM
Wireless-N: BPSK, QPSK, 16-QAM, 64-QAM
Peak Gain of the
Antenna
2-0.48dBi
dBi
Transmitted Power
802.11g:
22 +/-1dBm
(Typical)
802.11g: 12±1dBm
(Typical)
Wireless-N:
10±1dBm
(Typical)
Wireless-N: 25 +/-1dBm (Typical)
Receive Sensitivity
54Mbps @ -70dBm (Typical)
Wireless-N @ -70dBm (Typical)
Security Features
WEP Encryption Security
Dimensions
5.24" x 0.87" x 4.76" (133 mm x 22 mm x 121 mm)
Unit Weight
2.19 oz. (0.062 kg)
Power
3.3V
Operating Temp.
0ºC to 50ºC (32ºF to 122ºF)
Appendix F: Specifications
50
Wireless-N PCI Adapter
Storage Temp.
-25ºC to 70ºC (-13ºF to 158ºF)
Operating Humidity
10% to 80% Non-Condensing
Storage Humidity
5% to 90% Non-Condensing
Appendix F: Specifications
51
Wireless-N PCI Adapter
Appendix G: Warranty Information
LIMITED WARRANTY
Linksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially
free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under
this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any
rebates. This limited warranty extends only to the original purchaser.
If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return
Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are
requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a
copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You
are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You
only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling
charges.
ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED
TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives
You specific legal rights, and You may also have other rights which vary by jurisdiction.
This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated,
repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal
physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new
techniques for intruding upon and attacking networks, Linksys does not warrant that the Product will be free of
vulnerability to intrusion or attack.
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT,
OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF
LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT
(INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT
WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even
if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.
52
Appendix G: Warranty Information
Wireless-N PCI Adapter
Appendix H: Regulatory Information
FCC Statement
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
(1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment or devices.
(3) Connect the equipment to an outlet other than the receiver's. (4) Consult a dealer or an experienced radio/TV technician for assistance.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11.
This equipment
been SAR-evaluated
for expressly
use in notebooks
side
slotresponsible
configuration.
FCC
Caution: Anyhas
changes
or modifications not
approvedwith
by the
party
for compliance could void the user's authority to operate this equipment.
FCC Radiation Exposure Statement
This equipment
equipmentcomplies
complies
with
FCC
radiation
exposure
set for
forth
an uncontrolled
environment.
This
with
FCC
radiation
exposure
limitslimits
set forth
an for
uncontrolled
environment.
This equipment should be installed and operated with minimum distance 20cm
End
users
must
follow
the
specific
operating
instructions
for
satisfying
RF
exposure
compliance.
between the radiator & your body.
This
notnot
be be
co-located
or operating
in conjunction
with any
other
or transmitter.
This transmitter
transmittermust
must
co-located
or operating
in conjunction
with
anyantenna
other antenna
or transmitter.
Safety Notices
Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Do not use this product near water, for example, in a wet basement or near a
swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
IC STATEMENT
Operation is subject to the following two conditions:
(1) this device may not cause interference and (2)this device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IMPORTANT NOTE: 
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure
compliance. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Declaration d'Industrie Canada
Le fonctionnement est soumis aux conditions suivantes:
(1) Ce peripherique ne doit pas causer d'interferences;
(2)Ce peripherique doit accepter doit accepter toutes les interferences recues, y compris celles qui risquent d'entrainer un fonctionnement indesirable.
Appendix H: Regulatory Information
This device has been designed to operate with an antenna having a maximum gain of –0.48 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The
required antenna impedance is 50 ohms.
51
Wireless-N PCI Adapter
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic
Equipment (WEEE)
This document contains important information for users with regards to the proper disposal and recycling of Linksys
products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:
Appendix H: Regulatory Information
54
Wireless-N PCI Adapter
Appendix H: Regulatory Information
55
Wireless-N PCI Adapter
Appendix H: Regulatory Information
56
Wireless-N PCI Adapter
Appendix H: Regulatory Information
57
Wireless-G Notebook Adapter with RangeBooster
For more information, visit www.linksys.com.
Appendix H: Regulatory Information
58
Wireless-N PCI Adapter
Appendix I: Contact Information
Need to contact Linksys?
Visit us online for information on the latest products and updates
to your existing products at:
http://www.linksys.com or
ftp.linksys.com
Can't find information about a product you want to buy
on the web? Do you want to know more about networking
with Linksys products? Give our advice line a call at:
Or fax your request in to:
800-546-5797 (LINKSYS)
949-823-3002
If you experience problems with any Linksys product,
you can call us at:
Don't wish to call? You can e-mail us at:
800-859-2379
support@linksys.com
If any Linksys product proves defective during its warranty period,
you can call the Linksys Return Merchandise Authorization
department for obtaining a Return Authorization Number at:
(Details on Warranty and RMA issues can be found in the Warranty
Information section in this Guide.)
949-823-3000
59
Appendix I: Contact Information

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
Modify Date                     : 2006:05:04 14:03:23+08:00
Create Date                     : 2006:03:31 14:20:55Z
Page Count                      : 65
Page Mode                       : UseOutlines
Page Layout                     : SinglePage
About                           : uuid:68939d0f-7ded-4e38-966f-6d22755715a5
Producer                        : Acrobat Distiller 6.0.1 (Windows)
Creation Date                   : 2006:03:31 14:20:55Z
Mod Date                        : 2006:05:04 14:03:23+08:00
Author                          : junelee
Creator Tool                    : FrameMaker 7.0
Metadata Date                   : 2006:05:04 14:03:23+08:00
Document ID                     : uuid:7216ac66-7c15-4b5a-b20e-0327e240b89b
Format                          : application/pdf
Creator                         : junelee
Title                           : Book Template.book
Has XFA                         : No

EXIF Metadata provided by EXIF.tools