LINKSYS WPS54GV2 Wireless-G Print Server User Manual Book

LINKSYS LLC Wireless-G Print Server Book

Contents

Manual 1

Wireless-G PrintServerCopyright and TrademarksSpecifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. How to Use this User GuideThe user guide to the Wireless-G PrintServer has been designed to make understanding networking with the PrintServer easier than ever. Look for the following items when reading this User Guide:In addition to these symbols, there are definitions for technical terms that are presented like this:Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this:Figure numbers and descriptions can also be found in the “List of Figures” section. This exclamation point means there is a caution or warning and is something that could damage your property or the PrintServer.word: definition.This checkmark means there is a note of interest and is something you should pay special attention to while using the PrintServer.This question mark provides you with a reminder about something you might need to do while using the PrintServer.Figure 0-1: Sample Figure DescriptionWPS54G-UG-50315C JLWARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
Wireless-G PrintServerTable of ContentsChapter 1: Introduction 1Welcome 1What’s in this Guide? 2Chapter 2: Getting to Know the PrintServer 4The Bottom Panel 4The Front Panel 5Chapter 3: Connecting the PrintServer 6Overview 6Connecting the PrintServer to Your Network 6Placement Options 7Chapter 4: Configuring the PrintServer Using the Setup Wizard 8Starting the Setup Wizard 8Installing the PrintServer 8Chapter 5: Windows Driver Installation 19Overview 19Using the Instructions in This Chapter 19Driver Installation 20Configuration of the PrintServer Driver 22Chapter 6: Configuring the PrintServer Using the Web-based Utility 25Overview 25The Setup Tab 26The Protocol Tab - TCP/IP 27The Protocol Tab - AppleTalk 28The Protocol Tab - NetBEUI 29The Protocol Tab - SNMP 30The Wireless Tab - Basic 31The Wireless Tab - Security 32The Printer Tab - Internet Printing 33The Printer Tab - Logical Port 34The Status Tab - Device 35The Status Tab - Printer 36The Status Tab - Wireless 36The Exit Tab 36
Wireless-G PrintServerChapter 7: Bi-Admin Management 37Overview 37Bi-Admin Installation 37Starting the Bi-Admin Management Utility 39The Bi-Admin Management Utility 40Chapter 8: Internet Printing Protocol (IPP) 51Overview 51Windows IPP Client Setup 51Appendix A: Troubleshooting 56Common Problems and Solutions 56Appendix B: Wireless Security 58Security Precautions 58Security Threats Facing Wireless Networks 58Appendix C: About Bi-Directional Printing 61Appendix D: Upgrading Firmware 62Appendix E: Windows Help 63Appendix F: Glossary 64Appendix G: Specifications 71Appendix H: Warranty Information 72Appendix I: Regulatory Information 73Appendix J: Contact Information 75
Wireless-G PrintServerList of FiguresFigure 2-1: PrintServer’s Bottom Panel 4Figure 2-2: PrintServer’s Front Panel 5Figure 3-1: Connect to the Ethernet Port 6Figure 3-2: Connect to the USB Port 6Figure 3-3: Connect to the Power Port 6Figure 3-4: Desktop Placement 7Figure 4-1: Welcome 8Figure 4-2: Locate Your Printer 8Figure 4-3: Disconnect USB Printer from PC 9Figure 4-4: Connect Printer to PrintServer 9Figure 4-5: Connect PrintServer to the Router 10Figure 4-6: Connect Power to PrintServer 10Figure 4-7: Connect Power to Printer 11Figure 4-8: Select PrintServer 11Figure 4-9: Password 12Figure 4-10: Basic Settings 12Figure 4-11: IP Settings 13Figure 4-12: Set PrintServer’s Password 13Figure 4-13: Wireless Settings 14Figure 4-14: Wireless Security Settings - WPA 14Figure 4-15: Wireless Security Settings - WEP 15Figure 4-16: Confirmation 15Figure 4-17: Remove Power from PrintServer 16Figure 4-18: Disconnect Network Cable 16Figure 4-19: Reconnect Power to PrintServer 17Figure 4-20: Wireless is Now Active 17Figure 4-21: Installation of PrintServer Driver 18Figure 5-1: Welcome 20Figure 5-2: Driver Setup Welcome 20Figure 5-3: Choose Destination Location 20Figure 5-4: Select Program Folder 21
Wireless-G PrintServerFigure 5-5: Setup Complete 21Figure 5-6: Wireless-G PrintServer Setup 22Figure 5-7: Wireless-G PrintServer Diagnostic - Check Printer Driver Installation 22Figure 5-8: Printer Driver Not Installed 22Figure 5-9: Wireless-G PrintServer Diagnostic - Check Network Status 23Figure 5-10: Wireless-G PrintServer Diagnostic - Congratulations 23Figure 5-11: PrintServer Diagnostic Icon 24Figure 5-12: PrintServer Info 24Figure 5-13: Right-click Icon 24Figure 6-1: Setup Tab 26Figure 6-2: Protocol Tab - TCP/IP 27Figure 6-3: Protocol Tab - AppleTalk 28Figure 6-4: Protocol Tab - NetBEUI 29Figure 6-5: Protocol Tab - SNMP 30Figure 6-6: Wireless Tab - Basic 31Figure 6-7: Wireless Tab - Security (WEP) 32Figure 6-8: Wireless Tab - Security (WPA) 32Figure 6-9: Printer - Internet Printing 33Figure 6-10: Printer - Logical Port 34Figure 6-11: Status Tab - Device 35Figure 6-12: Firmware Upgrade 35Figure 6-13: Status Tab - Printer 36Figure 6-14: Status Tab - Wireless 36Figure 6-15: Exit 36Figure 7-1: Bi-Admin Setup Welcome 37Figure 7-2: Choose Destination Location 38Figure 7-3: Select Program Folder 38Figure 7-4: Connected Protocol 39Figure 7-5: Searching for Device 39Figure 7-6: Bi-Admin Management Utility 40Figure 7-7: Device Information 40Figure 7-8: Printer Status 41Figure 7-9: Configuration - System 42
Wireless-G PrintServerFigure 7-10: Configuration - TCP/IP 43Figure 7-11: Configuration - AppleTalk 44Figure 7-12: Configuration - NetBEUI 45Figure 7-13: Configuration - Internet Printing 46Figure 7-14: Configuration - Port 47Figure 7-15: Configuration - Wireless 48Figure 7-16: Configuration - SNMP 49Figure 7-17: Upgrade 50Figure 7-18: Detected LAN Cards 50Figure 7-19: BIN File Information 50Figure 7-20: Add Cross Segment PrintServer 50Figure 8-1: Windows XP - Local or Network Printer 53Figure 8-2: Windows XP - Specify a Printer 54Figure 8-3: Windows 2000 - Locate Your Printer 54Figure D-1: Status Tab - Device 62Figure D-2: Firmware Upgrade 62
1Chapter 1: IntroductionWelcomeWireless-G PrintServerChapter 1: IntroductionWelcomeThank you for choosing the Linksys Wireless-G PrintServer. The PrintServer lets you connect a USB printer directly to your network, eliminating the need to dedicate a PC to print sharing chores. Using a PrintServer frees up your “print share PC” so you don’t have to leave it on all the time. It also removes the printing bottleneck, and sets your PC free to do more useful work.The USB port is compatible with USB 1.1 printers, as well as printers that support the new high-speed USB 2.0 specification for even faster throughput.How does the PrintServer do all of this? A print server is a device that allows multiple computers to share a printer over a network. You can connect the PrintServer directly to your network using an Ethernet network cable, or you can connect the PrintServer over Wireless-G (802.11g) at up to 54Mbps. The wireless option lets you put your printer wherever you want to, without having to run a cable. Whichever way the PrintServer is attached to your network, both your wireless and wired PCs will have access to it and its USB printer.But what does all of this mean?Networks are useful tools for sharing Internet access and computer resources. Multiple computers can share Internet access, so you don’t need more than one high-speed Internet connection. Using the PrintServer, you can access one printer from different computers. Plus, you can access data located on another computer’s hard drive and play multi-player video games. So, networks not only are useful in homes and offices, but also can be fun.PCs on a wired network create a LAN, or Local Area Network. They are connected with Ethernet cables, which is why the network is called “wired”. PCs equipped with wireless cards or adapters can communicate without cumbersome cables. By sharing the same wireless settings, within their transmission radius, they form a wireless network. This is sometimes called a WLAN, or Wireless Local Area Network. Your network router bridges wireless networks of both 802.11b and 802.11g standards and wired networks, allowing them to communicate with each other.To guide you through the process of installing the PrintServer, run the Setup Wizard on the Setup CD-ROM (you can use the instructions in the Quick Installation or User Guide to help you). After you have installed the PrintServer, you can change its settings using its browser-based utility, which is described in this User Guide. These instructions should be all you need to get the most out of the Wireless-G PrintServer.ethernet: an IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission mediumlan (local area network): the computers and networking products that make up the network in your home or office802.11b: an IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz802.11g: an IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devicesbrowser: an application program that provides a way to look at and interact with all the information on the World Wide Webmbps: one million bits per second; a unit of measurement for data transmission
2Chapter 1: IntroductionWhat’s in this Guide?Wireless-G PrintServerWhat’s in this Guide?This user guide covers the steps for setting up and using the PrintServer.• Chapter 1: IntroductionThis chapter describes the PrintServer’s applications and this User Guide.• Chapter 2: Getting to Know the PrintServerThis chapter describes the physical features of the PrintServer.• Chapter 3: Connecting the PrintServerThis chapter instructs you on how to connect the PrintServer to your network.• Chapter 4: Configuring the PrintServer using the Setup WizardThis chapter instructs you on how to use the Setup Wizard to install your PrintServer.• Chapter 5: Windows Driver InstallationThis chapter explains how to install the Windows driver for the PrintServer.• Chapter 6: Configuring the PrintServer Using the Web-based UtilityThis chapter explains use the web-based utility to change the PrintServer’s settings.• Chapter 7: Bi-Admin ManagementThis chapter explains how to use the Bi-Admin Management utility, which is for advanced users only.• Chapter 8: Internet Printing Protocol (IPP)This chapter instruct you on how to use the PrintServer as an IPP server so you can run remote print jobs.• Appendix A: TroubleshootingThis appendix describes some potential problems and solutions regarding use of the PrintServer.• Appendix B: Wireless SecurityThis appendix explains the security risks in wireless networking and how you can help protect your network• Appendix C: About Bi-Directional PrintingThis appendix describes bi-directional printing.• Appendix D: Upgrading FirmwareThis appendix instructs you on how to upgrade the firmware on the PrintServer should you need to do so.
3Chapter 1: IntroductionWhat’s in this Guide?Wireless-G PrintServer• Appendix E: Windows HelpThis appendix describes how you can use Windows Help for instructions about networking, such as installing the TCP/IP protocol.• Appendix F: GlossaryThis appendix gives a brief glossary of terms frequently used in networking.• Appendix G: SpecificationsThis appendix provides the technical specifications for the PrintServer.• Appendix H: Warranty InformationThis appendix supplies the warranty information for the PrintServer.• Appendix I: Regulatory InformationThis appendix supplies the regulatory information regarding the PrintServer.• Appendix J: Contact InformationThis appendix provides contact information for a variety of Linksys resources, including Technical Support.
4Chapter 2: Getting to Know the PrintServerThe Bottom PanelWireless-G PrintServerChapter 2: Getting to Know the PrintServerThe Bottom PanelThe PrintServer’s ports and Reset button are located on the bottom panel.Power The Power port is where you will connect the power adapter.Ethernet The Ethernet port is where you will connect the PrintServer to your wired network. (This is optional.)USB Printer The USB Printer port is where you will connect the USB printer to the PrintServer.The USB icon (right) designates a USB port. The PrintServer comes with a USB cable. One end has a rectangular connector called Type A. The other end has a square connector called Type B. The USB cable’s Type A end connects to the PrintServer, and the Type B end connects to the printer. Reset Button Use the Reset Button to reset the PrintServer to its factory defaults or print a test page. The instructions are provided on the right side of this page.IMPORTANT: Resetting the PrintServer will delete all of your settings and replace them with the factory defaults. Do not reset the PrintServer if you want to retain the settings.Figure 2-1: PrintServer’s Bottom PanelTo reset the factory default settings1. Unplug the PrintServer.2. Press and hold the Reset button. While pressing the button, plug in the PrintServer.3. If you continue pressing the button for 10 seconds, the PrintServer will be reset to factory defaults.To generate a diagnostic print-out1. Ensure that both the PrintServer and the printer attached to the Printer port are ON.2. Press the Reset button, and hold it in for 2 seconds.3. The test page, which lists the current settings, will be printed. PostScript printers are unable to print this page. If you have a PostScript printer on the USB Printer port, the test page will not be printed.USB Connector-Type A  USB Connector-Type B
5Chapter 2: Getting to Know the PrintServerThe Front PanelWireless-G PrintServerThe Front PanelThe PrintServer’s LEDs are located on the front panel.Power Green/Orange. If the Power LED is continuously lit green, then the PrintServer is ready for use. The LED flashes green when the PrintServer is booting up, a system self-test is running, or the firmware is being upgraded. It lights up orange when there is an error.Ethernet Green/Orange. If the Ethernet LED is continuously lit green, the PrintServer is successfully connected to a device through the Ethernet port. The LED flashes green when the PrintServer is actively sending or receiving data from the wired network. It flashes orange when there are collisions detected on the Ethernet port.Wireless Green. The Wireless LED serves two purposes. If the LED is continuously lit, the PrintServer is successfully connected to the wireless network. If the LED is flashing, the PrintServer is actively sending or receiving data from the wireless network.USB Green/Orange. The USB LED lights up green when there is a printer connected to the USB port. The LED flashes green when the PrintServer is sending data through the USB port. It lights up orange when there is a problem with the USB printer.Figure 2-2: PrintServer’s Front Panel
6Chapter 3: Connecting the PrintServerOverviewWireless-G PrintServerChapter 3: Connecting the PrintServer Overview Before starting the physical installation, note the PrintServer’s default name, which starts with “LK” (for example, LK71107). The default name is shown in the Server field on the PrintServer’s sticker, which is located on the PrintServer’s back panel. During the PrintServer driver installation, this name is used to identify the PrintServer you are currently installing.Connecting the PrintServer to Your Network1. Use the USB cable to connect your USB printer to the PrintServer’s USB Printer port. Plug the Type A connector end into the PrintServer and the Type B connector end into the printer.2. If you are connecting the PrintServer to your wired network, then plug one end of the Ethernet network cable into the PrintServer’s Ethernet port.Then connect the other end of the cable to your router or switch. The distance between the PrintServer and the other device should not exceed 328 feet (100 meters).3. Power on your printer.4. Plug the power adapter into the PrintServer’s Power port.Then plug the other end into an electrical outlet.Proceed to the next section, “Placement Options.”Figure 3-1: Connect to the Ethernet PortNOTE: The PrintServer does not have an on/off power switch.  Whenever its power adapter is plugged into a power supply, the PrintServer is powered on. The PrintServer can be powered on before, during, or after your network is powered on. Figure 3-2: Connect to the USB PortFigure 3-3: Connect to the Power PortIMPORTANT: Make sure you use the power adapter supplied with the PrintServer. Use of a different power adapter could damage the PrintServer.
7Chapter 3: Connecting the PrintServerPlacement OptionsWireless-G PrintServerPlacement OptionsThere are different ways to place the PrintServer. The first way is to place the PrintServer horizontally on a surface, so it sits on four small rubber pads. You can also use the included velcro to mount the PrintServer on a wall or underneath a shelf. To use the velcro, follow these instructions:1. Separate the included velcro into its two sides, the hook side and the loop side. You will use the tape on the backs of the velcro sides to attach them to the PrintServer and surface you want to use.2. For the first velcro side, peel off the cover protecting the tape, and attach it to the recessed area on the back panel of the PrintServer.3. For the other velcro side, peel off the cover, and attach it to the location you have chosen for the PrintServer.4. Attach the velcro sides to each other, and make sure the PrintServer is securely mounted on the wall or underneath the shelf.5. Adjust the position of the antenna so that it is positioned as high as possible. Usually, the higher you place the antenna, the better the performance and range will be.The physical installation of the Wireless-G PrintServer is complete. Proceed to “Chapter 4: Configuring the PrintServer Using the Setup Wizard.” Figure 3-4: Desktop Placement
8Chapter 4: Configuring the PrintServer Using the Setup WizardStarting the Setup WizardWireless-G PrintServerChapter 4: Configuring the PrintServer Using the Setup WizardStarting the Setup WizardTo install the PrintServer, you will use the Setup CD-ROM to run the Setup Wizard. It is highly recommended that you use a computer on the wired network to set up the PrintServer. However, if you only have a wireless network, then you can use a computer on the wireless network to set up the PrintServer.1. Insert the Setup CD-ROM into the computer’s CD-ROM drive. The Setup Wizard should run automatically. If it does not, click the Start button and choose Run. In the box that appears, enter D:\setupWizard.exe  (if “D” is the letter of your CD-ROM drive).2. When you see the Welcome screen, you have four choices:Click Set up PrintServer to set up the PrintServer. Click Set up Computer if you have already installed the PrintServer. Then proceed to “Chapter 5: Windows Driver Installation”.Click User Guide button to view the User Guide. Click Exit to end the installation.Installing the PrintServer1. If you have not already done so, click Set up PrintServer on the Welcome screen.2. You will see a screen asking you to locate your USB printer. Click Next to continue.Figure 4-1: WelcomeFigure 4-2: Locate Your Printer
9Chapter 4: Configuring the PrintServer Using the Setup WizardInstalling the PrintServerWireless-G PrintServer3. You will see a screen asking you to disconnect the printer from your computer. Click Next.4. You will see a screen showing the proper USB connection between the PrintServer and your printer. Click Next to continue.Figure 4-3: Disconnect USB Printer from PCFigure 4-4: Connect Printer to PrintServer
10Chapter 4: Configuring the PrintServer Using the Setup WizardInstalling the PrintServerWireless-G PrintServer5. The next screen will show the proper connection between the PrintServer and your router. Click Next.6. The next screen will ask you to connect power to the PrintServer. Click Next.Figure 4-5: Connect PrintServer to the RouterFigure 4-6: Connect Power to PrintServer
11Chapter 4: Configuring the PrintServer Using the Setup WizardInstalling the PrintServerWireless-G PrintServer7. The next screen will ask you to connect power to your printer. Click Next.8. After the Setup Wizard has found the PrintServer, the Wireless-G PrintServer Setup screen will appear. A list of all compatible printer servers will be displayed. Your PrintServer is listed by its default server name. Next to the PrintServer’s Server Name is its IP Address. Note the IP Address so you can use it to access the PrintServer’s web-based utility, as described in “Chapter 6: Configuring the PrintServer Using the Web-based Utility.” Select the PrintServer you want to configure and click Next to continue.Click the Refresh button to refresh the screen. Click Back to return to the previous screen.Figure 4-7: Connect Power to PrinterFigure 4-8: Select PrintServer
12Chapter 4: Configuring the PrintServer Using the Setup WizardInstalling the PrintServerWireless-G PrintServer9. Enter the PrintServer’s default password, admin. Click Enter to continue. (You will be able to change this password later.)10. The Basic Settings screen will appear. If you want to change the PrintServer Name or Workgroup Name, enter the new names in the respective fields. Click Next to continue, or click Back to return to the previous screen.Figure 4-9: PasswordFigure 4-10: Basic Settings
13Chapter 4: Configuring the PrintServer Using the Setup WizardInstalling the PrintServerWireless-G PrintServer11. The IP Settings screen will appear. If your network uses a router with a DHCP setting that automatically assigns IP addresses, select Automatically obtain an IP address (DHCP). If your network uses a static IP address, select Set IP configuration manually, and enter the IP Address, Subnet Mask, and Gateway in the fields provided.Click Next to continue, or click Back to return to the previous screen.12. The Set PrintServer’s Password screen will appear. If you want to change your password, enter your current password in the Current Password field. Enter the new password in the New Password field, and then enter it again in the Verify Password field. Click Next to continue, or click Back to return to the previous screen.Figure 4-11: IP SettingsFigure 4-12: Set PrintServer’s Passwordstatic ip address: a fixed address assigned to a computer or device connected to a network.ip (internet protocol): a protocol used to send data over a networkip address: the address used to identify a computer or device on a network
14Chapter 4: Configuring the PrintServer Using the Setup WizardInstalling the PrintServerWireless-G PrintServer13. The Wireless Settings screen will appear. In the SSID field, enter your wireless network’s SSID or name. This is the unique name shared by all devices in a wireless network. The SSID is case-sensitive and should have 32 characters or fewer.Select the channel at which the network broadcasts its wireless signal (available only if you selected Ad-Hoc for the Network Type setting).The Network Type setting shows a choice of two wireless modes. Select Infrastructure if you want the PrintServer to communicate using an access point or wireless router. Select Ad-Hoc if you want the PrintServer to communicate without using an access point or wireless router.Click Next to continue, or click Back to return to the previous screen.14. The Wireless Security Settings screen will appear. Select the type of security you want to use: WEP (64-Bit), WEP (128-Bit), or WPA-Pre-Shared Key (TKIP). All devices in a network must use the same type. Then proceed to the appropriate instructions for your wireless security method.If you do not want to use wireless security, keep the default, Disabled.WPA-Pre-Shared Key (TKIP)Enter a Passphrase (also known as a Pre-Shared Key) that is 8-64 characters in length. Click Next to continue, or click Back to return to the previous screen.Figure 4-13: Wireless SettingsFigure 4-14: Wireless Security Settings - WPAad-hoc: a group of wireless devices  communicating directly to each other (peer-to-peer) without the use of an access point.infrastructure: configuration in which a wireless network is bridged to a wired network via an access point.ssid: your wireless network’s name.wpa (wi-fi protected access: a wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.
15Chapter 4: Configuring the PrintServer Using the Setup WizardInstalling the PrintServerWireless-G PrintServerWEPEnter a Passphrase. If you use a Passphrase, a WEP key will be automatically generated after you click the Next button. The Passphrase is case-sensitive and should have 16 alphanumeric characters or fewer. It must match the passphrase of your wireless network and is compatible with Linksys wireless products only. (You will have to enter the WEP key(s) manually on any non-Linksys wireless products.)If you want to enter the WEP key manually, then keep the default, Disabled. You will need to enable WEP encryption and enter the WEP key manually using the PrintServer’s Web-based Utility. (Refer to “Chapter 6: Configuring the PrintServer Using the Web-based Utility” for instructions.)Click Next to continue, or click Back to return to the previous screen.15. The Confirmation screen will appear. Your old and new settings will be displayed. If you want to save the new settings, click Next. If you want to make a change, click Back. If you want to exit the Setup Wizard, click Exit.Figure 4-15: Wireless Security Settings - WEPFigure 4-16: Confirmationpassphrase: used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption for Linksys products.wep (wired equivalent privacy): a method of encrypting data transmitted on a wireless network for greater security.
16Chapter 4: Configuring the PrintServer Using the Setup WizardInstalling the PrintServerWireless-G PrintServer16. After the new settings are saved, the next screen will ask you to remove the power from the PrintServer. Click Next to continue.17. The next screen will ask you to disconnect the network cable from the PrintServer. Click Next to continue.Figure 4-17: Remove Power from PrintServerFigure 4-18: Disconnect Network Cable
17Chapter 4: Configuring the PrintServer Using the Setup WizardInstalling the PrintServerWireless-G PrintServer18. The next screen will ask you to reconnect the power to the PrintServer. Click Next to continue.19. The next screen will indicate that the PrintServer is now part of your wireless network. Click Next to continue.Figure 4-19: Reconnect Power to PrintServerFigure 4-20: Wireless is Now Active
18Chapter 4: Configuring the PrintServer Using the Setup WizardInstalling the PrintServerWireless-G PrintServer20. The next screen will indicate that the setup of the PrintServer is complete. Now you will need to install the driver. Click Next to install the driver. The installation will occur automatically. Then proceed to the Configuration of the PrintServer Driver section of “Chapter 5: Windows Driver Installation”.If you have additional computers on your network, insert the Setup CD-ROM into the next computer and select Set up Computer on the Welcome screen. Then proceed to “Chapter 5: Windows Driver Installation”.If you want to make a change, click Back. If you want to exit the Setup Wizard, click Exit.Figure 4-21: Installation of PrintServer Driver
19Chapter 5: Windows Driver InstallationOverviewWireless-G PrintServerChapter 5: Windows Driver InstallationOverviewThis section installs the PrintServer’s software on your Windows 98, Me, 2000, or XP computers so they can use the PrintServer for print jobs. (The PrintServer is fully compatible with Windows 98, Me, 2000, and XP.)At this point, you must have the following:• the PrintServer hardware installed on your network. If not, see “Chapter 3: Connecting the PrintServer.”• the PrintServer configured on your network. If not, see “Chapter 4: Configuring the PrintServer Using the Setup Wizard.”• TCP/IP installed on each of your computers. • an IP address assigned to each of the computers on your network.• an IP address assigned to the PrintServer by you or your network router. By default the PrintServer has DHCP enabled so the network router will automatically assign an IP address. If you need to manually assign an IP address, run the Setup Wizard on the Setup CD-ROM or go to “Chapter 7: Bi-Admin Management.”It is assumed that your CD-ROM drive’s letter name is designated as “D”.  If your CD-ROM drive is named another letter, replace all instances of “D” with the appropriate letter.If you need to install the PrintServer’s driver on computers without a CD-ROM drive, you can create a setup disk by using a computer with a CD-ROM drive to copy the contents of D:\Driver\PTP onto a floppy disk. Using the Instructions in This ChapterIf you followed the instructions in “Chapter 4: Configuring the PrintServer Using the Setup Wizard,” then the driver has already been installed. Proceed to this section, “Configuration of the PrintServer Driver.”If you clicked Set up Computer on the Welcome screen of the Setup Wizard, then proceed to the next section, “Driver Installation.”HAVE YOU: already set up your printer? Linksys recommends that you set up your printer and install your printer’s driver before you install the PrintServer’s driver.
20Chapter 5: Windows Driver InstallationDriver InstallationWireless-G PrintServerDriver Installation1. Make sure you have no programs or applications running on your computer.2. If you haven’t already done so, insert the Setup CD-ROM into the computer’s CD-ROM drive. The Setup CD-ROM should run automatically. If it does not, click the Start button and choose Run. In the field that appears, enter D:\setupWizard.exe (if “D” is the letter of your CD-ROM drive).3. When you see the Welcome screen, click Set up Computer to continue.If you have not set up the PrintServer, click Set up PrintServer. Then proceed to “Chapter 4: Configuring the PrintServer Using the Setup Wizard”. To view the User Guide, click User Guide. To end the installation, click Exit.4. The Welcome screen of the Print Server Driver program will appear first. Click Next to continue with the driver installation, or click Cancel to quit the setup program and then close the open programs. 5. The Choose Destination Location screen will appear. Choose the location where the driver’s folder will be installed. To install the driver in the default location, click Next to continue. If you want the folder to be installed in a different location, click the Browse button and select the location. Then click Next to continue.You can also click Back to return to the previous screen or click Cancel to end the driver installation.Figure 5-3: Choose Destination LocationFigure 5-2: Driver Setup WelcomeFigure 5-1: Welcome
21Chapter 5: Windows Driver InstallationDriver InstallationWireless-G PrintServer6. The Select Program Folder screen will appear. An icon will be added to the program folder listed. You may change the name for the program folder, if you wish. Click Next. You can also click Back to return to the previous screen or click Cancel to end the driver installation.7. When the driver is installed, the Setup Complete screen will appear. The Print Driver must still be configured, so make sure that Configure Print Driver now is selected. Click Finish to end the driver installation and begin the driver configuration.Figure 5-4: Select Program FolderFigure 5-5: Setup Complete
22Chapter 5: Windows Driver InstallationConfiguration of the PrintServer DriverWireless-G PrintServerConfiguration of the PrintServer Driver1. The Wireless-G PrintServer Setup screen will automatically appear. Select the appropriate printer, and then click Next.2. The Wireless-G PrintServer Diagnostic - Check Printer Driver Installation screen will appear. Select the driver for your printer, and click Next to continue.If you need to assign a driver, then click Assign and follow the on-screen instructions.If the driver for your printer is not installed, you will see a new window pop up. The message will ask you to exit the Wizard and install the driver for your printer. Click OK and install the driver. After the driver has been installed, run the Setup Wizard and click Driver Install on the Welcome screen.Figure 5-7: Wireless-G PrintServer Diagnostic - Check Printer Driver InstallationFigure 5-6: Wireless-G PrintServer SetupNOTE: If the PrintServer is not listed, then click Refresh. If the PrintServer cannot be found, then select Disable Firewall when Searching PrintServer and click Refresh again.Figure 5-8: Printer Driver Not Installed
23Chapter 5: Windows Driver InstallationConfiguration of the PrintServer DriverWireless-G PrintServer3. The Wireless-G PrintServer Diagnostic - Check Network Status screen will appear. Make sure the status says “Connected” and then click Next. If the status does not say “Connected,” then double-check the cable connections and PrintServer settings.4. The Wireless-G PrintServer Diagnostic - Congratulations screen will appear. If you want to print a test page, click Test Print. Then click Finish.Figure 5-9: Wireless-G PrintServer Diagnostic - Check Network StatusFigure 5-10: Wireless-G PrintServer Diagnostic - Congratulations
24Chapter 5: Windows Driver InstallationConfiguration of the PrintServer DriverWireless-G PrintServer5. The Print Server diagnostic icon will appear in the system tray of your desktop. When you double-click the icon, you will see the PrintServer Info screen. If you want to run the wizard that configures the printer driver, click the Diagnostics button. To close the PrintServer Info screen, click the Close button.When you right-click the Print Server diagnostic icon, you will see a menu. To see the version number of the Print Server Utility, click About. To see the PrintServer Info screen, click Info. To close the Utility, click Exit.The driver installation and configuration is complete. You can now use the PrintServer.If you would like to change the PrintServer’s settings, use the PrintServer’s web-based utility. For more information, refer to “Chapter 6: Configuring the PrintServer Using the Web-based Utility.”Figure 5-11: PrintServer Diagnostic IconFigure 5-12: PrintServer InfoFigure 5-13: Right-click Icon
25Chapter 6: Configuring the PrintServer Using the Web-based UtilityOverviewWireless-G PrintServerChapter 6: Configuring the PrintServer Using the Web-based UtilityOverviewAfter setting up the PrintServer with the Setup Wizard, the PrintServer will be ready for use. However, if you’d like to change its settings, use the PrintServer’s web-based utility. This chapter will describe each web page of the utility and each page’s key functions. The utility can be accessed via your web browser through the use of a networked computer.There are six main tabs: Setup, Protocol, Wireless, Printer, Status, and Exit. Additional tabs will be available after you click one of the main tabs, except for the Setup tab.To access the web-based utility, launch Internet Explorer or Netscape Navigator, and enter the PrintServer’s IP address in the Address field. Then press Enter.NOTE: Use the PrintServer’s IP address that you noted when you ran the Setup Wizard. Otherwise, insert the Setup CD-ROM, and when the Welcome screen appears, click Setup Wizard. Follow the instructions until you reach the Wireless-G PrintServer Setup screen. Note the IP address, and then click Back until you reach the Welcome screen. Click Exit.
26Chapter 6: Configuring the PrintServer Using the Web-based UtilityThe Setup TabWireless-G PrintServerThe Setup TabThe first screen that appears is the Setup tab and allows you to change the PrintServer’s general settings.WPS54G Device NameEnter the PrintServer’s name in the field provided. The name is located on a sticker on the bottom of the PrintServer.PasswordCurrent Password. To change the PrintServer’s password, enter the current password in the Current Password field. New Password and Verify Password. Enter the new password in the New Password field, and then enter the new password again in the Verify Password field.ProtocolsThe TCP/IP protocol is enabled by default.Enable: Apple Talk or NetBEUI. Check the box(es) for AppleTalk or NetBEUI, if they are used by your network. Click the Save button to apply your changes, or click Cancel to cancel your changes.Figure 6-1: Setup Tab
27Chapter 6: Configuring the PrintServer Using the Web-based UtilityThe Protocol Tab - TCP/IPWireless-G PrintServerThe Protocol Tab - TCP/IPClick the TCP/IP tab to view or change the TCP/IP values of the PrintServer.IP AddressObtain an IP Address Automatically. If your network router is using DHCP to assign IP addresses, select Obtain an IP Address Automatically. By default, Obtain an IP Address Automatically is enabled.Use the Following IP Address. If you need to assign the PrintServer a fixed IP address (also known as static IP address), select Use the Following IP Address, and enter the appropriate values under IP Address, Subnet Mask, and Gateway. Make sure the IP Address and Subnet Mask are appropriate for your network. If you change the PrintServer’s IP address, make sure you that you reconnect to the PrintServer using that new IP address. Otherwise, you will not be communicating with the PrintServer. In most cases, the Gateway IP address is the IP address of your router, and you should complete the Gateway field if you will use the PrintServer for Internet printing. (To find out your router’s IP address, consult your router’s documentation.) ConnectionDelay before reconnection attempt. Set how long you want the PrintServer to wait between attempts.Number of reconnection attempts. Specify the number of times that the PrintServer will attempt to connect to the network.Click the Save button to apply your changes, or click Cancel to cancel your changes.Figure 6-2: Protocol Tab - TCP/IP
28Chapter 6: Configuring the PrintServer Using the Web-based UtilityThe Protocol Tab - AppleTalkWireless-G PrintServerThe Protocol Tab - AppleTalkAppleTalk is a network communications protocol that allows computers to talk to each other using Ethernet. Typically only Macintoshes use AppleTalk, although other platforms can use it if they have the necessary, third-party software.CommunicationPrinter Object Type. The Printer Object Type can be obtained from the manufacturer of the printer. Enter the type of printer in the field provided. For each printer connected to the PrintServer, you will choose the Communications Protocol that allows the devices on the network to communicate. Communication Protocol. Select the type of Communication Protocol you will use, ASCII or Binary for each printer, according to the recommendation of the printer’s manufacturer. For more information, refer to the printer’s documentation.Click the Save button to apply your changes, or click Cancel to cancel your changes.Figure 6-3: Protocol Tab - AppleTalk
29Chapter 6: Configuring the PrintServer Using the Web-based UtilityThe Protocol Tab - NetBEUIWireless-G PrintServerThe Protocol Tab - NetBEUINetBEUI connection settings of the PrintServer are available on this tab.Domain NameEnter the name of the domain that you want the PrintServer associated with in the Domain Name field.If you are unsure of the Domain Name, you can find it out by looking on any computer already on the network.  In Windows 98, right-click Network Neighborhood and select Properties. Under the Identification tab, there will be listed that computer’s name, and the Domain to which it is connected. For Windows Me, 2000, or XP, right-click My Network Places. In Windows Me, choose Properties from the menu that appears. In Windows 2000 or XP, choose Properties from the menu that appears. Then, right-click Local Area Connection and choose Properties. The Domain name will appear. If you want the PrintServer to be connected to that same Domain, enter that Domain name here.  If no Domain name exists there, you will use the Workgroup name from that window.OptionsResponse Time. You can specify the Response Time that you prefer for the PrintServer. This is the amount of time (measured in seconds) that the PrintServer will wait for a response from the network before “timing out.”Abort Print Job if Error. You also have the option to use this feature, Abort Print Job if Error. Selecting Yes here will terminate the printing if there is an error of any kind. If you select No, print jobs that have errors will be sent to the printer, but might not print properly.Click the Save button to apply your changes, or click Cancel to cancel your changes.Figure 6-4: Protocol Tab - NetBEUI
30Chapter 6: Configuring the PrintServer Using the Web-based UtilityThe Protocol Tab - SNMPWireless-G PrintServerThe Protocol Tab - SNMPUse this screen to view or change the PrintServer’s SNMP (Simple Network Management Protocol) settings.The PrintServer supports SNMP, which allows network administrators to monitor and control the PrintServer through the use of network management platforms, such as HP OpenView.The appropriate MIB file must be imported into your SNMP management program using the Import-Compile command. Check your program’s documentation for details on this procedure. The MIB file is named Mib2p.mib and is provided in the MiB folder on the Setup CD-ROM.GeneralSysContact. Enter the name of the contact person in the SysContact field. SysLocation. Enter the location of the contact person in the SysLocation field.Management StationsStation No. Select the number of the management station from the Station No. drop-down menu (1-4). Click the Get Data button to display the information for the selected station.IP Address. Enter the IP address of the management station running the SNMP program.Community. Enter the name of the SNMP community, which is usually public or private. Access. Select the level of access for this management station, Not Accessible, Read-only, or Read/Write.Trap ReceiversReceiver No. Select the number of the trap receiver from the Receiver No. drop-down menu (1-4). Click the Get Data button to display the information for the selected trap receiver.IP Address. Enter the IP address of the trap receiver that will be sent the trap messages or notifications.Community. In the Community field, enter the name of the SNMP community, which is usually public or private.Enable with Severity level. To designate a severity level, click the checkbox next to Enable with Severity level. From the following drop-down menu, select the desired level of severity, with 1 meaning least severe.Click the Save button to apply your changes, or click Cancel to cancel your changes.Figure 6-5: Protocol Tab - SNMP
31Chapter 6: Configuring the PrintServer Using the Web-based UtilityThe Wireless Tab - BasicWireless-G PrintServerThe Wireless Tab - BasicThis screen allows you to change the PrintServer’s basic wireless settings.ConfigurationRegulatory Domain and MAC Address. The PrintServer’s Regulatory Domain and MAC Address are listed and cannot be changed. SSID. In the SSID field, enter the name of your wireless network. This is the unique name shared by all devices in a wireless network. The SSID is case-sensitive and should have 32 characters or fewer.Channel No. If your network is set to ad-hoc mode, select your network’s channel setting from the Channel No. drop-down menu.Network Type. The Network Type setting shows a choice of two wireless modes. Select Infrastructure if you want the PrintServer to communicate using an access point or wireless router. Select Ad-Hoc if you want the PrintServer to communicate without using an access point or wireless router.Click the Save button to apply your changes, or click Cancel to cancel your changes.Figure 6-6: Wireless Tab - Basic
32Chapter 6: Configuring the PrintServer Using the Web-based UtilityThe Wireless Tab - SecurityWireless-G PrintServerThe Wireless Tab - SecurityConfigure the security of your wireless network on this screen. Wi-Fi Protected Access (WPA) and two levels of Wired Equivalent Privacy (WEP) encryption are available. If you do not want to use wireless security, select None from the Security Mode drop-down menu.Wireless SecuritySecurity Mode. To use WPA, select Pre-Shared Key. To use WEP, select the level of WEP encryption you want to use, 64 Bit Keys (10 Hex chars) or 128 Bit Keys (26 Hex chars). Then proceed to the instructions for your security method.WEPDefault Transmit Key. Select the Default Transmit Key used by your wireless network. This indicates which WEP key your network uses for WEP encryption.Passphrase. Enter a Passphrase and click the Generate Keys button to automatically generate WEP Keys 1-4. The Passphrase is case-sensitive and should have no more than 16 alphanumeric characters. It must match your wireless network’s passphrase and is compatible with Linksys wireless products only. (Enter the WEP key(s) manually on any non-Linksys wireless products.)Key 1 to Key 4. To enter the WEP keys manually, leave the Passphrase field blank and enter your WEP key(s). For 64-bit WEP encryption, each key must have 10 hexadecimal characters, while for 128-bit WEP encryption, the key must have 26 hexadecimal characters. Valid hexadecimal characters are “0”-“9” and “A”-“F”.Authentication. Select your wireless network’s authentication type. The default is Open System, for which the sender and the recipient do NOT use a WEP key for authentication. You can also choose Shared Key, for which the sender and recipient use a WEP key for authentication.Click the Save button to apply your changes, or click Cancel to cancel your changes.Pre-Shared Key (WPA)WPA Algorithm. TKIP is the default algorithm.WPA Shared Key. Enter your Pre-Shared Key, which must have 8-63 characters in length.Click the Save button to apply your changes, or click Cancel to cancel your changes.Figure 6-7: Wireless Tab - Security (WEP)Figure 6-8: Wireless Tab - Security (WPA)
33Chapter 6: Configuring the PrintServer Using the Web-based UtilityThe Printer Tab - Internet PrintingWireless-G PrintServerThe Printer Tab - Internet PrintingInternet Printing allows you to automatically print any e-mails that are sent to a specific e-mail account on your network. This is especially useful for printing information when you are not connected to the network. You can print from any location where you can access e-mail.Mail ServerMail Server IP Address. Enter the address of your mail server. (This value must be a fixed IP address.) Account Name and Password. Enter the Account Name and Account Password.Verify Password. Enter the password again in the Verify Password field. Check Mail every. Specify how often you want the PrintServer to check for e-mail to be printed.Redirect unprintable Mail to. Specify an e-mail address to which e-mails that cannot be printed are routed; this is useful for both graphic-intensive e-mails and for troubleshooting purposes.PrinterPrinter Model. Enter the Printer Model in the field provided. You can find this in the Device Manager. Printer Port. Choose the appropriate Printer Port from the drop-down menu: USB, the PrintServer’s USB port, or Logical Printer 1-3. The PrintServer has three logical or virtual printer ports. For example, you can have three different configurations for your USB printer: Logical Printer 1 for landscape orientation, Logical Printer 2 for double-sided copies, and Logical Printer 3 for manual feed. Then configure the Logical Printers on the Logical Port tab, so Logical Printers 1, 2, and 3 will be mapped to the physical printer on the PrintServer’s USB port.OptionsPrint every E-Mail. Click this checkbox if you want to print every e-mail message.Print Banner Page. Enabled by default, this feature tells the PrintServer to print a banner page for every print job (the banner page describes the print job). Click the checkbox to remove the checkmark and disable this feature.Mail response when printed. Click this checkbox if you want an e-mail sent when a print job is complete.Click the Save button to apply your changes, or click Cancel to cancel your changes.Figure 6-9: Printer - Internet Printing

Navigation menu