LINKSYS WRT160N Wireless-N Broadband Router User Manual

LINKSYS LLC Wireless-N Broadband Router Linksys WRT160N User Guide

a href="https://usermanual.wiki/LINKSYS" itemprop="url"> LINKSYS >

Manual 2

Chapter 3 Advanced Configuration7Wireless-N Broadband Routerinactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 15 minutes.Keep Alive: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default value is 30 seconds.L2TPL2TP is a service that applies to connections in Israel only.Internet Connection Type > L2TPServer IP Address This is the IP address of the L2TP Server. Your ISP will provide you with the IP Address you need to specify here.Username and Password Enter the Username and Password provided by your ISP.Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 15 minutes.Keep Alive: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default Redial Period is 30 seconds.Telstra CableTelstra Cable is a service that applies to connections in Australia only.Internet Connection Type > Telstra CableServer IP Address This is the IP address of the Heartbeat Server. Your ISP will provide you with the IP Address you need to specify here.Username and Password Enter the Username and Password provided by your ISP.Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to have elapsed before your Internet connection terminates. The default Max Idle Time is 15 minutes.Keep Alive: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, you specify how often you want the Router to check the Internet connection. The default Redial Period is 30 seconds.Optional SettingsSome of these settings may be required by your ISP. Verify with your ISP before making any changes.Optional SettingsHost Name and Domain Name These fields allow you to supply a host and domain name for the Router. Some ISPs, usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a
Chapter 3 Advanced Configuration8Wireless-N Broadband Routerhost and domain name. In most cases, leaving these fields blank will work. MTU MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet transmission. Select Manual if you want to manually enter the largest packet size that is transmitted. To have the Router select the best MTU for your Internet connection, keep the default setting, Auto.Size When Manual is selected in the MTU field, this option is enabled. Leave this value in the 1200 to 1500 range. The default size depends on the Internet Connection Type:DHCP, Static IP, or Telstra: 1500PPPoE: 1492PPTP or L2TP: 1460Network SetupThe Network Setup section changes the settings on the network connected to the Router’s Ethernet ports. Wireless setup is performed through the Wireless tab.Router IPThis presents both the Router’s IP Address and Subnet Mask as seen by your network.Router IPDHCP Server SettingThe settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. If you choose to enable the Router’s DHCP server option, make sure there is no other DHCP server on your network. DHCP Server SettingDHCP Server DHCP is enabled by factory default. If you already have a DHCP server on your network, or you don’t want a DHCP server, then select Disabled (no other DHCP features will be available).DHCP Reservation Click this button if you want to assign a fixed local IP address to a MAC address. •••DHCP ReservationYou will see a list of DHCP clients with the following information: Client Name, Interface, IP Address, and MAC Address. DHCP ReservationSelect Clients from DHCP Table Click the Select check box to reserve a client’s IP address. Then click Add Clients.Manually Adding Client To manually assign an IP address, enter the client’s name in the Enter Client Name field. Enter the IP address you want it to have in the Assign IP Address field. Enter its MAC address in the To This MAC Address field. Then click Add.Clients Already ReservedA list of DHCP clients and their fixed local IP addresses will be displayed at the bottom of the screen. If you want to remove a client from this list, click Remove.Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. To view the most up-to-date information, click Refresh. To exit this screen, click Close.Start IP Address Enter a value for the DHCP server to start with when issuing IP addresses. Because the Router’s default IP address is 192.168.1.1, the Start IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.253. The default Starting IP Address is 192.168.1.100.Maximum Number of Users Enter the maximum number of PCs that you want the DHCP server to assign IP addresses to. This number cannot be greater than 253. The default is 50.IP Address Range Displayed here is the range of available IP addresses.••
Download:
Mirror Download [FCC.gov]
Document ID874381
Application IDT4j/UhRSrDsr815/pdyPUg==
Document DescriptionManual 2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize198.48kB (2481042 bits)
Date Submitted2007-11-30 00:00:00
Date Available2007-11-30 00:00:00
Creation Date2007-10-24 14:55:24
Producing SoftwareAdobe PDF Library 7.0
Document Lastmod2007-11-29 11:57:14
Document TitleLinksys WRT160N User Guide
Document CreatorAdobe InDesign CS2 (4.0.5)
Document Author: Linksys
FCC ID Filing: Q87-WRT160N

Navigation menu