LINKSYS WUSB54GX4 Wireless-G USB Network Adapter with SRX400 User Manual Book

LINKSYS LLC Wireless-G USB Network Adapter with SRX400 Book

Manual

Model No.USB Network Adapter Wireless-GWUSB54GX4User GuideWIRELESSGHz2.4802.11gwith SRX400
Wireless-G USB Network Adapter with SRX400Copyright and TrademarksSpecifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2006 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.How to Use This User GuideThis User Guide has been designed to make understanding networking with the Wireless-G USB Network Adapter with SRX400 easier than ever. Look for the following items when reading this User Guide:In addition to these symbols, there are definitions for technical terms that are presented like this:Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this:Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.This exclamation point means there is a caution or warning and is something that could damage your property or the Wireless-G USB Network Adapter with SRX400.This checkmark means there is a note of interest and is something you should pay special attention to while using the Wireless-G USB Network Adapter with SRX400.This question mark provides you with a reminder about something you might need to do while using the Wireless-G USB Network Adapter with SRX400.word: definition.Figure 0-1: Sample Figure DescriptionWUS54GX4-UG-60215NC BWWARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
Wireless-G USB Network Adapter with SRX400Table of ContentsChapter 1: Introduction 1Welcome 1What’s in This User Guide? 1Chapter 2: Planning Your Wireless Network 3Network Topology 3Roaming 3Network Layout 4Chapter 3: Getting to Know the Wireless-G USB Network Adapter with SRX400 5Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400 6Starting the Setup Wizard 6Setting Up the Adapter 7Chapter 5: Using the Wireless Network Monitor 17Accessing the Wireless Network Monitor 17Link Information Screens 17Site Survey 20Profiles 22Creating a New Profile 23Appendix A: Troubleshooting 33Common Problems and Solutions 33Frequently Asked Questions 34Appendix B: Using Windows XP Wireless Zero Configuration 37Appendix C: Wireless Security 40Security Precautions 40Security Threats Facing Wireless Networks 40Appendix D: Windows Help 43Appendix E: Glossary 44Appendix F: Specifications 49Appendix G: Warranty Information 50Appendix H: Regulatory Information 51Appendix I: Contact Information 57
Wireless-G USB Network Adapter with SRX400List of FiguresFigure 3-1: USB Network Adapter with SRX400’s USB Port 5Figure 3-2: USB Network Adapter with SRX400’s LEDs 5Figure 4-1: Setup Wizard’s Welcome Screen 6Figure 4-2: Setup Wizard’s License Agreement 6Figure 4-3: Connecting the Adapter Screen 7Figure 4-4: Available Wireless Network Screen 7Figure 4-5: Available Wireless Network Screen 8Figure 4-6: WEP Key Needed for Connection 8Figure 4-7: WPA-Personal Needed for Connection 9Figure 4-8: WPA2-Personal Needed for Connection 9Figure 4-9: Congratulations Screen 9Figure 4-10: Available Wireless Network Screen 10Figure 4-11: Network Settings Screen 10Figure 4-12: Wireless Mode Screen 11Figure 4-13: Ad-Hoc Mode Settings Screen 11Figure 4-14: Wireless Security Screen 12Figure 4-15: Wireless Security - WEP Screen 12Figure 4-16: Wireless Security - WPA Personal Screen 13Figure 4-17: Wireless Security - WPA2 Personal Screen 13Figure 4-18: Wireless Security - WPA Enterprise Using EAP-TLS Screen 14Figure 4-19: Wireless Security - WPA Enterprise Using PEAP Screen 14Figure 4-20: Wireless Security - RADIUS Screen 15Figure 4-21: Wireless Security - PEAP Screen 15Figure 4-22: Confirm New Settings Screen 16Figure 4-23: Congratulations Screen 16Figure 5-1: Wireless Network Monitor Icon 17Figure 5-2: Link Information Screen 17Figure 5-3: More Information - Wireless Network Status Screen 18Figure 5-4: More Information - Wireless Network Statistics Screen 19Figure 5-5: Site Survey Screen 20Figure 5-6: WEP Key Needed for Connection 20Figure 5-7: WPA-Personal Needed for Connection 21Figure 5-8: WPA2-Personal Needed for Connection 21
Wireless-G USB Network Adapter with SRX400Figure 5-9: Profiles Screen 22Figure 5-10: Import a Profile 22Figure 5-11: Export a Profile 22Figure 5-12: Create a New Profile 23Figure 5-13: Available Wireless Network Screen 23Figure 5-14: Available Wireless Network Screen 24Figure 5-15: WEP Key Needed for Connection 24Figure 5-16: WPA-Personal Needed for Connection 25Figure 5-17: WPA2-Personal Needed for Connection 25Figure 5-18: Congratulations Screen 25Figure 5-19: Available Wireless Network Screen 26Figure 5-20: Network Settings Screen 26Figure 5-21: Wireless Mode Screen 27Figure 5-22: Ad-Hoc Mode Settings 27Figure 5-23: Wireless Security Screen 28Figure 5-24: Wireless Security - WEP Screen 28Figure 5-25: Wireless Security - WPA Personal Screen 29Figure 5-26: Wireless Security - WPA2 Personal Screen 29Figure 5-27: Wireless Security - WPA Enterprise Using EAP-TLS Screen 30Figure 5-28: Wireless Security - WPA Enterprise Using PEAP Screen 30Figure 5-29: Wireless Security - RADIUS Screen 31Figure 5-30: Wireless Security - RADIUS Screen 31Figure 5-31: Confirm New Settings Screen 32Figure 5-32: Congratulations Screen 32Figure B-1: Wireless Network Monitor Icon 37Figure B-2: Windows XP - Use Windows XP Wireless Configuration 37Figure B-3: Windows XP Wireless Configuration Icon 37Figure B-4: Available Wireless Network 38Figure B-5: No Wireless Security 38Figure B-6: Network Connection - Wireless Security 39Figure B-7: Wireless Network Connection 39
1Chapter 1: IntroductionWelcomeWireless-G USB Network Adapter with SRX400Chapter 1: IntroductionWelcomeThank you for choosing the Wireless-G USB Network Adapter with SRX400. With this Adapter, your wireless networking experience will be faster and easier than ever.How does the Adapter do this? Like all wireless products, the Adapter allows for greater range and mobility within your wireless network, whether it’s using the Wireless-G (802.11g) or Wireless-B (802.11b) standard. But with SRX400, your speed and range are even better than before. And with USB, connection is simple.But what does all of this mean?Networks are useful tools for sharing computer resources. You can access one printer from different computers and access data located on another computer's hard drive. Networks are even used for playing multiplayer video games. So, networks are not only useful in homes and offices, they can also be fun.PCs equipped with wireless cards and adapters can communicate without cumbersome cables. By sharing the same wireless settings, within their transmission radius, they form a wireless network.The included Setup Wizard walks you through configuring the Adapter to your wireless network settings, step by step. Use the instructions in this Guide to help you set up and connect the Adapter using the Setup Wizard. These instructions should be all you need to get the most out of the Adapter.What’s in This User Guide?This user guide covers the steps for setting up and using the Wireless-G USB Network Adapter with SRX400.• Chapter 1: IntroductionThis chapter describes the Adapter’s applications and this User Guide.• Chapter 2: Planning Your Wireless NetworkThis chapter discusses a few of the basics about wireless networking.• Chapter 3: Getting to Know the Wireless-G USB Network Adapter with SRX400This chapter describes the physical features of the Adapter.• Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400This chapter shows you how to set up and connect the Adapter.802.11b: an IEEE wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.adapter: a device that adds network functionality to your PC.network: a series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users.802.11g an IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz.
2Chapter 1: IntroductionWhat’s in This User Guide?Wireless-G USB Network Adapter with SRX400• Chapter 5: Using the Wireless Network Monitor This chapter explains how to use the Adapter’s Wireless Network Monitor.• Appendix A: TroubleshootingThis appendix describes some problems and solutions, as well as frequently asked questions, regarding installation and use of the Adapter.• Appendix B: Using Windows XP Wireless Zero ConfigurationThis chapter instructs you on how to use Window XP Wireless Zero Configuration.• Appendix C: Wireless SecurityThis appendix discusses security issues regarding wireless networking and measures you can take to help protect your wireless network.• Appendix D: Windows HelpThis appendix describes how you can use Windows Help for instructions about networking, such as installing the TCP/IP protocol.• Appendix E: GlossaryThis appendix gives a brief glossary of terms frequently used in networking.• Appendix F: SpecificationsThis appendix provides the Adapter’s technical specifications.• Appendix G: Warranty InformationThis appendix supplies the Adapter’s warranty information.• Appendix H: Regulatory InformationThis appendix supplies the Adapter’s regulatory information.• Appendix I: Contact InformationThis appendix provides contact information for a variety of Linksys resources, including Technical Support.
3Chapter 2: Planning Your Wireless NetworkNetwork TopologyWireless-G USB Network Adapter with SRX400Chapter 2: Planning Your Wireless NetworkNetwork TopologyA wireless network is a group of computers, each equipped with one wireless adapter. Computers in a wireless network must be configured to share the same radio channel. Several PCs equipped with wireless cards or adapters can communicate with one another to form an ad-hoc network.Linksys wireless adapters also provide users access to a wired network when using an access point or wireless router. An integrated wireless and wired network is called an infrastructure network. Each wireless PC in an infrastructure network can talk to any computer in a wired network infrastructure via the access point or wireless router.An infrastructure configuration extends the accessibility of a wireless PC to a wired network, and can double the effective wireless transmission range for two wireless adapter PCs. Since an access point is able to forward data within a network, the effective transmission range in an infrastructure network can be doubled.RoamingInfrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your wireless PC within your network and the access points will pick up the wireless PC's signal, providing that they both share the same channel and SSID.Before you consider enabling roaming, choose a feasible radio channel and optimum access point position. Proper access point positioning combined with a clear radio signal will greatly enhance performance.infrastructure: a wireless network that is bridged to a wired network via an access point.ad-hoc: a group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access point.roaming: the ability to take a wireless device from one access point's range to another without losing the connection.ssid: your wireless network's name.topology: the physical layout of a network.access point: a device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network
4Chapter 2: Planning Your Wireless NetworkNetwork LayoutWireless-G USB Network Adapter with SRX400Network LayoutLinksys wireless access points and wireless routers have been designed for use with 802.11b and 802.11g products. Products using the 802.11g and 802.11b standards can communicate with each other.Access points and wireless routers are compatible with 802.11b and 802.11g adapters, such as the notebook adapters for your laptop computers, PCI adapters for your desktop PCs, and USB adapters for when you want to enjoy USB connectivity. Wireless products will also communicate with a wireless print server.When you wish to connect your wired network with your wireless network, network ports on access points and wireless routers can be connected to any of Linksys's switches or routers.With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at www.linksys.com for more information about wireless products. router: a networking device that connects multiple networks togetherswitch: a data switch that connects computing devices to host computers, allowing a large number of devices to share a limited number of ports
5Chapter 3: Getting to Know the Wireless-G USB Network Adapter with SRX400Wireless-G USB Network Adapter with SRX400Chapter 3: Getting to Know the Wireless-G USB Network Adapter with SRX400The USB PortThe USB Port is where you connect the USB cable.The LEDsThe USB Network Adapter’s LEDs displays information about network activity.LINK Green. The LINK LED lights up when the Adapter has an active connection.ACT Green. The ACT LED flashes when there is network activity.Figure 3-1: USB Network Adapter’s USB PortFigure 3-2: USB Network Adapter’s LEDs
6Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400Starting the Setup WizardWireless-G USB Network Adapter with SRX400Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400The Wireless-G USB Network Adapter with SRX400 is set up with the Setup Wizard that comes on the CD enclosed with the Adapter. This chapter will guide you through the setup procedure. Starting the Setup WizardTo begin the setup process, insert the Setup Wizard CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the Welcome screen should appear. If it does not, click the Start button and choose Run. In the field that appears, enter D:\setup.exe (if “D” is the letter of your CD-ROM drive). On the Welcome screen, you have the following choices:Click Here to Start - Click the Click Here to Start button to begin the software installation process. User Guide - Click the User Guide button to open this User Guide. Exit - Click Exit to exit the Setup Wizard.1. To install the Adapter, click the Click Here to Start button on the Welcome screen.2. After reading the License Agreement, click Next if you agree and want to continue the installation, or click Cancel to end the installation.Figure 4-1: Setup Wizard’s Welcome ScreenFigure 4-2: Setup Wizard’s License AgreementIMPORTANT: Do not connect the Adapter until you are instructed to do so or the setup will not work.
7Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400Setting Up the AdapterWireless-G USB Network Adapter with SRX4003. Windows will begin copying the files onto your PC.4. The Setup Wizard will now prompt you to install the Adapter into your PC. Click Next. Connect one end of the supplied USB cable into the USB port of the USB Network Adapter with SRX400 and connect the other end into the USB port of your computer. Adjust the antennas and continue the Setup Wizard.Setting Up the AdapterWhen the Setup Wizard resumes, the next screen to appear will be the Available Wireless Network screen.This screen provides two options for setting up the Adapter.•Available Wireless Network. Most users should use this option. The networks available to this Adapter will be listed on this screen. You can choose one of these networks and click the Connect button to connect to it. Click the Refresh button to update the Available Wireless Network list.•Manual Setup. To set up the Adapter manually, select Manual Setup.The setup for each option is described, step by step, under the appropriate heading on the following pages.Click Exit to close the Setup Wizard, if you wish to set up the Adapter later.Figure 4-3: Connecting the Adapter ScreenFigure 4-4: Available Wireless Network Screen
8Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400Setting Up the AdapterWireless-G USB Network Adapter with SRX400Setting Up the Adapter with an Available NetworkThe available networks are listed in the table on the center of the screen by SSID. Select the wireless network you wish to connect to and click the Connect button. (If you do not see your network listed, you can click the Refresh button to bring the list up again.) If the network utilizes wireless security, you will need to configure security on the Adapter. If not, you will be taken directly to the Congratulations screen. 1. If wireless security has been enabled on this network, you will see a wireless security screen. If your network uses WEP (Wired Equivalent Privacy) encryption, the WEP Key Needed for Connection screen will appear. If your network uses WPA Personal or WPA2 Personal security, a screen will appear for one of those encryption methods.WEP Key Needed for ConnectionSelect the level of encryption you want to use, 64-bit or 128-bit. Then, enter a passphrase or WEP key.Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The passphrase is case-sensitive and should not be longer than 31 alphanumeric characters. It must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key 1 - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption, enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel.Figure 4-5: Available Wireless Network ScreenFigure 4-6: WEP Key Needed for Connectionwep (wired equivalent privacy): a method of encrypting network data transmitted on a wireless network for greater security.encryption: encoding data transmitted in a network.wpa (wi-fi protected access): a wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.
9Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400Setting Up the AdapterWireless-G USB Network Adapter with SRX400WPA-Personal for ConnectionWPA Personal offers two encryption methods, TKIP and AES, with dynamic encryption keys. Select one of these methods. Then enter a passphrase.Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. The longer and more complex your Passphrase is, the more secure your network will be.Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel.WPA2 - Personal Needed for ConnectionAES is automatically used as the encryption method. Enter a passphrase on this screen.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. The longer and more complex your Passphrase is, the more secure your network will be.Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel. 2. After the Adapter has been configured for the network, the Congratulations screen will appear. Click Connect to Network to connect to your network.Congratulations! Setup is complete.To check the link information, search for available wireless networks, or make additional configuration changes, refer to “Chapter 5: Using the Wireless Network Monitor.”Figure 4-7: WPA-Personal Needed for ConnectionFigure 4-9: Congratulations ScreenFigure 4-8: WPA2-Personal Needed for Connection
10Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400Setting Up the AdapterWireless-G USB Network Adapter with SRX400Setting Up the Adapter with Manual SetupClick Manual Setup on the Available Wireless Network screen to set up the Adapter manually. 1. After clicking Manual Setup, the Network Settings screen will appear. If your network has a router or other DHCP server, click the radio button next to Obtain network settings automatically (DHCP).If your network does not have a DHCP server, click the radio button next to Specify network settings. Enter an IP Address, Subnet Mask, Default Gateway, and DNS addresses appropriate for your network. You must specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and DNS addresses, leave these fields empty. IP Address - This IP Address must be unique to your network.Subnet Mask - The Adapter’s Subnet Mask must be the same as your wired network’s Subnet Mask.Default Gateway - Enter the IP address of your network’s Gateway here. DNS 1 and DNS 2 - Enter the DNS address of your wired Ethernet network here.Click Next to continue, or click Back to return to the Available Wireless Network screen.Figure 4-10: Available Wireless Network ScreenFigure 4-11: Network Settings Screenip address: the address used to identify a computer or device on a network.default gateway: a device that forwards Internet traffic from your local area network.dns (domain name server): the IP address of your ISP's server, which translates the names of websites into IP addresses. subnet mask: an address code that determines the size of a network.
11Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400Setting Up the AdapterWireless-G USB Network Adapter with SRX400 2. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio button if you want to connect to a wireless router or access point. Click the Ad-Hoc Mode radio button if you want to connect to another wireless device directly without using a wireless router or access point. Then, enter the SSID for your network.Infrastructure Mode - Use this mode if you want to connect to a wireless router or access point.Ad-Hoc Mode - Use this mode if you want to connect to another wireless device directly without using a wireless router or access point.SSID - This is the wireless network name that must be used for all the devices in your wireless network. It is case- sensitive and should be a unique name to help prevent others from entering your network.Click Next to continue or Back to return to the previous screen. 3. If you chose Infrastructure Mode, go to Step 4 now. If you chose Ad-Hoc Mode, the Ad-Hoc Mode Settings screen will appear. Select your channel and network mode settings on this screen.Channel - Select the correct channel for your wireless network. The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which channel to use, keep the default setting.Click Next to continue or click Back to change any settings.Figure 4-12: Wireless Mode ScreenFigure 4-13: Ad-Hoc Mode Settings Screen
12Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400Setting Up the AdapterWireless-G USB Network Adapter with SRX400 4. The Wireless Security screen will appear.If your wireless network doesn’t use wireless security, select Disabled and then click the Next button to continue. Proceed to Step 5.From the Security drop-down menu, select the security method you want to use: WEP, WPA Personal, WPA2 Personal, WPA Enterprise, or RADIUS. WEP stands for Wired Equivalent Privacy, and WPA uses a security standard stronger than WEP encryption. RADIUS stands for Remote Authentication Dial-In User Service. Then proceed to the appropriate instructions for your security method.WEP Select a level of WEP encryption to use, and then enter a passphrase or WEP key.WEP - To use WEP encryption, select 64-bit or 128-bit characters from the drop-down menu.Passphrase - Instead of manually entering a WEP key, you can enter a passphrase in the Passphrase field, so a WEP key is automatically generated. This case-sensitive passphrase must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key- The WEP key you enter must match the WEP key of your wireless network. If you are using 64-bit WEP encryption, then the key must consist of exactly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Advanced Users:TX Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit key number 2, 3, or 4, select the appropriate number from the TX Key drop-down box.Authentication - The default is set to Auto, where it auto-detects for Shared Key or Open system. Shared Key is when both the sender and the recipient share a WEP key for authentication. Open key is when the sender and the recipient do not share a WEP key for authentication. All devices on your network must use the same authentication type.Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen.Figure 4-14: Wireless Security ScreenFigure 4-15: Wireless Security - WEP Screen
13Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400Setting Up the AdapterWireless-G USB Network Adapter with SRX400WPA Personal Select an encryption method, TKIP or AES, and then enter a passphrase.Encryption - Select the type of algorithm, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase of 8-63 characters in the Passphrase field. Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen.WPA2 Personal WPA2 Personal automatically uses AES, which is a stronger encryption method than TKIP. Enter a passphrase on this screen.Passphrase - Enter a Passphrase of 8-63 characters in the Passphrase field. Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen.Figure 4-16: Wireless Security - WPA Personal ScreenFigure 4-17: Wireless Security - WPA2 Personal Screen
14Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400Setting Up the AdapterWireless-G USB Network Adapter with SRX400WPA EnterpriseWPA Enterprise is used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) WPA Enterprise offers two encryption methods, TKIP and AES, with dynamic encryption keys. It offers two authentication methods, EAP-TLS and PEAP. Select one of these methods and follow the appropriate instructions below.EAP-TLSLogin Name - Enter the login name of your wireless network.Server Name - Enter the name of the authentication server (this is optional).Certificate - Select the certificate you have installed to authenticate you on your wireless network. If you want to use any certificate, keep the default setting, Trust Any.Encryption - Select the type of algorithm you want to use, TKIP or AES.PEAPLogin Name - Enter the login name of your wireless network.Password - Enter the password of your wireless network.Server Name - Enter the name of the authentication server (this is optional).Certificate - Select the certificate you have installed to authenticate you on your wireless network. If you want to use any certificate, keep the default setting, Trust Any.Inner Authen. - Select the authentication method used inside the PEAP tunnel.Encryption - Select the type of algorithm you want to use, TKIP or AES.Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen.Figure 4-18: Wireless Security - WPA Enterprise Using EAP-TLS ScreenFigure 4-19: Wireless Security - WPA Enterprise Using PEAP Screen
15Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400Setting Up the AdapterWireless-G USB Network Adapter with SRX400RADIUSRADIUS uses the security of a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) It offers two authentication methods, EAP-TLS and PEAP. Select one of these methods and follow the appropriate instructions below.EAP-TLSLogin Name - Enter the login name of your wireless network.Server Name - Enter the name of the authentication server (this is optional).Certificate - Select the certificate you have installed to authenticate you on your wireless network. If you want to use any certificate, keep the default setting, Trust Any.PEAPLogin Name - Enter the login name of your wireless network.Password - Enter the password of your wireless network.Server Name - Enter the name of the authentication server (this is optional).Certificate - Select the certificate you have installed to authenticate you on your wireless network.Inner Authen. - Select the authentication method used inside the PEAP tunnel.Encryption - Select the type of algorithm you want to use, TKIP or AES.Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen.Figure 4-20: Wireless Security - RADIUS Screenradius (remote authentication dial-in user service): a protocol that uses an authentication server to control network access.Figure 4-21: Wireless Security - PEAP Screen
16Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400Setting Up the AdapterWireless-G USB Network Adapter with SRX400 5. The next screen displays all of the Adapter’s settings. If these are correct, click Save to save these settings to your hard drive. If these settings are not correct, click Back to change your settings. 6. After the software has been successfully installed, the Congratulations screen will appear. Click Connect to Network to connect to your network. Click Return to Profiles screen to open the Wireless Network Monitor’s Profiles screen. For more information about the Wireless Network Monitor, refer to “Chapter 5: Using the Wireless Network Monitor.”Congratulations! Setup is complete.To check the link information, search for available wireless networks, or make additional configuration changes, refer to “Chapter 5: Using the Wireless Network Monitor.”Figure 4-22: Confirm New Settings ScreenFigure 4-23: Congratulations Screen
17Chapter 5: Using the Wireless Network MonitorAccessing the Wireless Network MonitorWireless-G USB Network Adapter with SRX400Chapter 5: Using the Wireless Network MonitorUse the Wireless Network Monitor to check the link information, search for available wireless networks, or create profiles that hold different configuration settings.Accessing the Wireless Network MonitorAfter setting up and connecting the Adapter, the Wireless Network Monitor icon will appear in your PC’s system tray. If the Wireless Network Monitor is enabled, then the icon will be green. If the Wireless Network Monitor is disabled or the Adapter is not connected, then the icon will be gray.Link Information ScreensThe opening screen of the Wireless Network Monitor is the Link Information screen. From this screen, you can find out how strong the current wireless signal is and how good the connection’s quality is. You can also click the More Information button to view additional status and statistics about the current wireless connection. To search for available wireless networks, click the Site Survey tab. To perform configuration changes or create connection profiles, click the Profiles tab.Link InformationThe Link Information screen displays network mode, signal strength, and link quality information about the current connection. It also provides a button to click for additional status information.Ad-Hoc Mode or Infrastructure Mode - The screen indicates whether the Adapter is currently working in Ad-Hoc or Infrastructure mode.Signal Strength - The Signal Strength bar indicates signal strength. Link Quality - The Link Quality bar indicates the quality of the wireless network connection.Click the More Information button to view additional information about the wireless network connection on the Wireless Network Status screen.Figure 5-1: Wireless Network Monitor IconFigure 5-2: Link Information ScreenNOTE: The Wireless Network Monitor should only be accessed AFTER installing the Adapter. For more information on setting up and connecting the Adapter, refer to “Chapter 4: Setting Up and Connecting the Wireless-G USB Network Adapter with SRX400.”
18Chapter 5: Using the Wireless Network MonitorLink Information ScreensWireless-G USB Network Adapter with SRX400Wireless Network StatusThe Wireless Network Status screen provides information on your current network settings.Status - This shows the status of the wireless network connection.SSID - This is the unique name of the wireless network. Wireless Mode - The mode of the wireless network currently in use is displayed here.Transfer Rate - The data transfer rate of the current connection is shown here.Channel - This is the channel to which the wireless network devices are set. Security - The status of the wireless security feature is displayed here.Authentication - This is your wireless network’s authentication method.IP Address - The IP Address of the Adapter is displayed here.Subnet Mask - The Subnet Mask of the Adapter is shown here.Default Gateway - The Default Gateway address of the Adapter is displayed here.DNS - This is the DNS address of the Adapter.DHCP Client - This displays the Adapter’s status as a DHCP client.MAC Address- The MAC address of the wireless network’s access point or wireless router is shown here.Signal Strength - The Signal Strength bar indicates the signal strength. Link Quality - The Link Quality bar indicates the quality of the wireless network connection.Click the Back button to return to the initial Link Information screen. Click the Statistics button to go to the Wireless Network Statistics screen. Click the Save to Profile button to save the currently active connection settings to a profile.Figure 5-3: More Information - Wireless Network Status Screen
19Chapter 5: Using the Wireless Network MonitorLink Information ScreensWireless-G USB Network Adapter with SRX400Wireless Network StatisticsThe Wireless Networks Statistics screen provides statistics on your current network settings.Transmit Rate - This is the data transfer rate of the current connection. (In Auto mode, the Adapter dynamically shifts to the fastest data transfer rate possible at any given time.)Receive Rate - This is the rate at which data is received.Packets Received - This shows the number of packets received by the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Packets Transmitted - This shows the number of packets transmitted from the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Bytes Received - This shows the number of bytes received by the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Bytes Transmitted - This shows the number of bytes transmitted from the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Driver Version - This shows the version of the Adapter’s driver.Noise Level - This shows the level of background noise affecting the wireless signal. A lower reading translates into a higher quality signal.Signal Strength - This is the intensity of the wireless signal received by the Adapter.Up Time - This indicates the length of the most recent connection to a wireless network.Total Up Time - This indicates the cumulative total of the Adapter’s connection time.Signal Strength - The Signal Strength bar indicates the signal strength. Link Quality - The Link Quality bar indicates the quality of the wireless network connection.Refresh - Click the Refresh button to reset the statistics.Click the Back button to return to the initial Link Information screen. Click the Status button to go to the Wireless Network Status screen. Click the Save to Profile button to save the currently active connection settings to a profile.Figure 5-4: More Information - Wireless Network Statistics Screen
20Chapter 5: Using the Wireless Network MonitorSite SurveyWireless-G USB Network Adapter with SRX400Site SurveyThe Site Survey screen displays a list of available networks in the table on the left. The table shows each network’s SSID, Channel, and the quality of the wireless signal the Adapter is receiving. You may click SSID, CH (Channel), or Signal, to sort by that field.SSID - The SSID or unique name of the wireless network is displayed here.CH - This is the channel that the network uses.Signal - This is the percentage of signal strength, from 0 to 100%.Site InformationFor each network selected, the following settings are listed:SSID - This the SSID or unique name of the wireless network. Wireless Mode - This is the mode of the wireless network currently in use.Channel - This is the channel to which the wireless network devices are set. Security - The status of the wireless security feature is displayed here.MAC Address- The MAC address of the wireless network’s access point is displayed here.Refresh - Click the Refresh button to perform a new search for wireless devices.Connect - To connect to one of the networks on the list, select the wireless network, and click the Connect button. If the network has wireless security enabled, a screen requiring security information will appear.If the network has WEP encryption enabled, then you will see the WEP Key Needed for Connection screen. Select the appropriate level of WEP encryption, 64-bit or 128-bit Then enter the network’s Passphrase or WEP Key. To connect to the network, click Connect. To cancel the connection, click Cancel.Figure 5-5: Site Survey ScreenFigure 5-6: WEP Key Needed for Connection
21Chapter 5: Using the Wireless Network MonitorSite SurveyWireless-G USB Network Adapter with SRX400If the network has WPA Personal security enabled, then you will see the WPA-Personal Needed for Connection screen. Select the appropriate encryption type, TKIP or AES. Enter the network’s Passphrase or pre-shared key in the Passphrase field. To connect to the network, click Connect. To cancel the connection, click Cancel.If the network has WPA2 Personal security enabled, then you will see the WPA2-Personal Needed for Connection screen. Enter the network’s Passphrase or pre-shared key in the Passphrase field. To connect to the network, click Connect. To cancel the connection, click Cancel.Figure 5-7: WPA-Personal Needed for ConnectionFigure 5-8: WPA2-Personal Needed for Connection
22Chapter 5: Using the Wireless Network MonitorProfilesWireless-G USB Network Adapter with SRX400ProfilesThe Profiles screen lets you save different configuration profiles for different network setups. The table on the left displays a list of available profiles with their profile names and SSIDs.Profile - The name of the profile is displayed here.SSID - The SSID or unique name of the wireless network is displayed here.Site InformationFor each profile selected, the following are listed:Wireless Mode - This is the mode of the wireless network currently in use.Channel - This is the channel to which the wireless network devices are set. Security - The status of the wireless security feature is displayed here.Authentication - The authentication setting for the network is shown here.Connect - To connect to a wireless network using a specific profile, select the profile, and click the Connect button.New - Click New to create a new profile. See the next section, “Creating a New Profile,” for detailed instructions.Edit - Select the profile you want to change, and then click Edit. Import - Click Import to import a profile that has been saved in another location. Select the appropriate file, and click the Open button.Export - Select the profile you want to save in a different location, and click Export. Direct Windows to the appropriate folder, and click the Save button.Delete - Select the profile you want to delete, and then click Delete. Figure 5-9: Profiles ScreenFigure 5-10: Import a ProfileFigure 5-11: Export a ProfileNOTE: If you want to export more than one profile, you have to export them one at a time.
23Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with SRX400Creating a New ProfileOn the Profiles screen, click the New button to create a new profile. Enter a name for the new profile, and click the OK button. Click the Cancel button to return to the Profiles screen without entering a name.The Available Wireless Network screen provides two options for setting up a profile.•Available Wireless Network. Most users should use this option. The networks available to this Adapter will be listed on this screen. You can choose one of these networks and click the Connect button to connect to it. Click the Refresh button to update the Available Wireless Network list.•Manual Setup. To set up the Adapter manually, select Manual Setup.The setup for each option is described, step by step, under the appropriate heading on the following pages.Click Exit to close the Setup Wizard, if you wish to set up the Adapter later.Figure 5-12: Create a New ProfileFigure 5-13: Available Wireless Network Screen
24Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with SRX400Setting Up the Adapter with an Available NetworkThe available networks are listed in the table on the center of the screen by SSID. Select the wireless network you wish to connect to and click the Connect button. (If you do not see your network listed, you can click the Refresh button to bring the list up again.) If the network utilizes wireless security, you will need to configure security on the Adapter. If not, you will be taken directly to the Congratulations screen.1. If wireless security has been enabled on this network, you will see a wireless security screen. If your network uses WEP (Wired Equivalent Privacy) encryption, the WEP Key Needed for Connection screen will appear. If your network uses WPA Personal or WPA2 Personal security, a screen will appear for one of those encryption methods.WEP Key Needed for ConnectionSelect the level of encryption you want to use, 64-bit or 128-bit. Then, enter a passphrase or WEP key.Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The passphrase is case-sensitive and should not be longer than 31 alphanumeric characters. It must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key 1 - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption, enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel.Figure 5-14: Available Wireless Network ScreenFigure 5-15: WEP Key Needed for Connection
25Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with SRX400WPA-Personal for ConnectionWPA Personal offers two encryption methods, TKIP and AES, with dynamic encryption keys. Select one of these methods. Then enter a passphrase.Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. The longer and more complex your Passphrase is, the more secure your network will be.Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel.WPA2 - Personal Needed for ConnectionAES is automatically used as the encryption method. Enter a passphrase on this screen.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. The longer and more complex your Passphrase is, the more secure your network will be.Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel.2. After the Adapter has been configured for the network, the Congratulations screen will appear. Click Connect to Network to connect to your network.Congratulations! The profile is complete.Figure 5-16: WPA-Personal Needed for ConnectionFigure 5-17: WPA2-Personal Needed for ConnectionFigure 5-18: Congratulations Screen
26Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with SRX400Setting Up the Adapter with Manual SetupClick Manual Setup on the Available Wireless Network screen to set up the Adapter manually. 1. After clicking Manual Setup, the Network Settings screen will appear. If your network has a router or other DHCP server, click the radio button next to Obtain network settings automatically (DHCP).If your network does not have a DHCP server, click the radio button next to Specify network settings. Enter an IP Address, Subnet Mask, Default Gateway, and DNS addresses appropriate for your network. You must specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and DNS addresses, leave these fields empty. IP Address - This IP Address must be unique to your network.Subnet Mask - The Adapter’s Subnet Mask must be the same as your wired network’s Subnet Mask.Default Gateway - Enter the IP address of your network’s Gateway here. DNS 1 and DNS 2 - Enter the DNS address of your wired Ethernet network here.Click Next to continue, or click Back to return to the Available Wireless Network screen.Figure 5-19: Available Wireless Network ScreenFigure 5-20: Network Settings Screen
27Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with SRX400 2. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio button if you want to connect to a wireless router or access point. Click the Ad-Hoc Mode radio button if you want to connect to another wireless device directly without using a wireless router or access point. Then, enter the SSID for your network.Infrastructure Mode - Use this mode if you want to connect to a wireless router or access point.Ad-Hoc Mode - Use this mode if you want to connect to another wireless device directly without using a wireless router or access point.SSID - This is the wireless network name that must be used for all the devices in your wireless network. It is case- sensitive and should be a unique name to help prevent others from entering your network.Click Next to continue or Back to return to the previous screen. 3. If you chose Infrastructure Mode, go to Step 4 now. If you chose Ad-Hoc Mode, the Ad-Hoc Mode Settings screen will appear. Select your channel and network mode settings on this screen.Channel - Select the correct channel for your wireless network. The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which channel to use, keep the default setting.Click Next to continue or click Back to change any settings.Figure 5-22: Ad-Hoc Mode SettingsFigure 5-21: Wireless Mode Screen
28Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with SRX400 4. The Wireless Security screen will appear.If your wireless network doesn’t use wireless security, select Disabled and then click the Next button to continue. Proceed to Step 5.From the Security drop-down menu, select the security method you want to use: WEP, WPA Personal, WPA2 Personal, WPA Enterprise, or RADIUS. WEP stands for Wired Equivalent Privacy, and WPA uses a security standard stronger than WEP encryption. RADIUS stands for Remote Authentication Dial-In User Service. Then proceed to the appropriate instructions for your security method.WEP Select a level of WEP encryption to use, and then enter a passphrase or WEP key.WEP - To use WEP encryption, select 64-bit or 128-bit characters from the drop-down menu.Passphrase - Instead of manually entering a WEP key, you can enter a passphrase in the Passphrase field, so a WEP key is automatically generated. This case-sensitive passphrase must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key- The WEP key you enter must match the WEP key of your wireless network. If you are using 64-bit WEP encryption, then the key must consist of exactly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Advanced Users:TX Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit key number 2, 3, or 4, select the appropriate number from the TX Key drop-down box.Authentication - The default is set to Auto, where it auto-detects for Shared Key or Open system. Shared Key is when both the sender and the recipient share a WEP key for authentication. Open key is when the sender and the recipient do not share a WEP key for authentication. All devices on your network must use the same authentication type.Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen.Figure 5-23: Wireless Security ScreenFigure 5-24: Wireless Security - WEP Screen
29Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with SRX400WPA Personal Select an encryption method, TKIP or AES, and then enter a passphrase.Encryption - Select the type of algorithm, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase of 8-63 characters in the Passphrase field. Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen.WPA2 Personal WPA2 Personal automatically uses AES, which is a stronger encryption method than TKIP. Enter a passphrase on this screen.Passphrase - Enter a Passphrase of 8-63 characters in the Passphrase field. Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen.Figure 5-25: Wireless Security - WPA Personal ScreenFigure 5-26: Wireless Security - WPA2 Personal Screen
30Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with SRX400WPA EnterpriseWPA Enterprise is used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) WPA Enterprise offers two encryption methods, TKIP and AES, with dynamic encryption keys. It offers two authentication methods, EAP-TLS and PEAP. Select one of these methods and follow the appropriate instructions below.EAP-TLSLogin Name - Enter the login name of your wireless network.Server Name - Enter the name of the authentication server (this is optional).Certificate - Select the certificate you have installed to authenticate you on your wireless network. If you want to use any certificate, keep the default setting, Trust Any.Encryption - Select the type of algorithm you want to use, TKIP or AES.PEAPLogin Name - Enter the login name of your wireless network.Password - Enter the password of your wireless network.Server Name - Enter the name of the authentication server (this is optional).Certificate - Select the certificate you have installed to authenticate you on your wireless network. If you want to use any certificate, keep the default setting, Trust Any.Inner Authen. - Select the authentication method used inside the PEAP tunnel.Encryption - Select the type of algorithm you want to use, TKIP or AES.Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen.Figure 5-27: Wireless Security - WPA Enterprise Using EAP-TLS ScreenFigure 5-28: Wireless Security - WPA Enterprise Using PEAP Screen
31Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with SRX400RADIUSRADIUS uses the security of a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) It offers two authentication methods, EAP-TLS and PEAP. Select one of these methods and follow the appropriate instructions below.EAP-TLSLogin Name - Enter the login name of your wireless network.Server Name - Enter the name of the authentication server (this is optional).Certificate - Select the certificate you have installed to authenticate you on your wireless network. If you want to use any certificate, keep the default setting, Trust Any.PEAPLogin Name - Enter the login name of your wireless network.Password - Enter the password of your wireless network.Server Name - Enter the name of the authentication server (this is optional).Certificate - Select the certificate you have installed to authenticate you on your wireless network.Inner Authen. - Select the authentication method used inside the PEAP tunnel.Encryption - Select the type of algorithm you want to use, TKIP or AES.Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen.Figure 5-29: Wireless Security - RADIUS ScreenFigure 5-30: Wireless Security - RADIUS Screen
32Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with SRX400 5. The next screen displays all of the Adapter’s settings. If these are correct, click Save to save these settings to your hard drive. If these settings are not correct, click Back to change your settings. 6. After the software has been successfully installed, the Congratulations screen will appear. Click Connect to Network to connect to your network. Click Return to Profiles screen to open the Wireless Network Monitor’s Profiles screen.Congratulations! The profile is complete.Figure 5-32: Congratulations ScreenFigure 5-31: Confirm New Settings Screen
33Appendix A: TroubleshootingCommon Problems and SolutionsWireless-G USB Network Adapter with SRX400Appendix A: TroubleshootingThis appendix consists of two parts: “Common Problems and Solutions” and “Frequently Asked Questions.” This appendix provides solutions to problems that may occur during the installation and operation of the Wireless-G USB Network Adapter. Read the description below to solve your problems. If you can't find an answer here, check the Linksys website at www.linksys.com.Common Problems and Solutions1.My computer does not recognize the USB Network Adapter.• Make sure that the USB Network Adapter is properly inserted into the USB port.• Also, make sure that the USB Controller is enabled in the BIOS. Check with your motherboard User Guide for more information.2. The USB Network Adapter does not work properly.• Reinsert the USB Network Adapter into the notebook or desktop’s USB port. • Right-click on My Computer, and select Properties. Select the Adapter, then chose the Device Manager tab, and click on the Network Adapter. You will find the USB Network Adapter if it is installed successfully. If you see a yellow exclamation mark, the resources may be conflicting and you must follow the steps below:• Uninstall the driver software from your PC.• Restart your PC and repeat the hardware and software installation as specified in this User Guide.3. I cannot communicate with the other computers linked via Ethernet in the Infrastructure configuration.• Make sure that the notebook or desktop is powered on.• Make sure that your USB Network Adapter is configured on the same channel, SSID, and WEP as the other computers in the Infrastructure configuration..
34Appendix A: TroubleshootingFrequently Asked QuestionsWireless-G USB Network Adapter with SRX400Frequently Asked QuestionsCan I run an application from a remote computer over the wireless network?This will depend on whether or not the application is designed to be used over a network. Consult the application’s user guide to determine if it supports operation over a network.Can I play computer games with other members of the wireless network?Yes, as long as the game supports multiple players over a LAN (local area network). Refer to the game’s user guide for more information.What is the IEEE 802.11b standard?It is one of the IEEE standards for wireless networks. The 802.11b standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11b standard. The 802.11b standard states a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.What is the IEEE 802.11g standard?It is one of the IEEE standards for wireless networks. The 802.11g standard allows wireless networking hardware from different manufacturers to communicate, provided that the hardware complies with the 802.11g standard. The 802.11g standard states a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz.What IEEE 802.11b features are supported?The product supports the following IEEE 802.11b functions: • CSMA/CA plus Acknowledge protocol • Multi-Channel Roaming • Automatic Rate Selection • RTS/CTS feature • Fragmentation • Power Management •What IEEE 802.11g features are supported?The product supports the following IEEE 802.11g functions: • CSMA/CA plus Acknowledge protocol • OFDM protocol• Multi-Channel Roaming • Automatic Rate Selection • RTS/CTS feature • Fragmentation• Power Management
35Appendix A: TroubleshootingFrequently Asked QuestionsWireless-G USB Network Adapter with SRX400What is ad-hoc mode?When a wireless network is set to ad-hoc mode, the wireless-equipped computers are configured to communicate directly with each other. The ad-hoc wireless network will not communicate with any wired network. What is infrastructure mode?When a wireless network is set to infrastructure mode, the wireless network is configured to communicate with a wired network through a wireless access point.What is roaming?Roaming is the ability of a portable computer user to communicate continuously while moving freely throughout an area greater than that covered by a single access point. Before using the roaming function, the workstation must make sure that it is the same channel number with the access point of dedicated coverage area. To achieve true seamless connectivity, the wireless LAN must incorporate a number of different functions. Each node and access point, for example, must always acknowledge receipt of each message. Each node must maintain contact with the wireless network even when not actually transmitting data. Achieving these functions simultaneously requires a dynamic RF networking technology that links access points and nodes. In such a system, the user’s end node undertakes a search for the best possible access to the system. First, it evaluates such factors as signal strength and quality, as well as the message load currently being carried by each access point and the distance of each access point to the wired backbone. Based on that information, the node next selects the right access point and registers its address. Communications between end node and host computer can then be transmitted up and down the backbone.As the user moves on, the end node’s RF transmitter regularly checks the system to determine whether it is in touch with the original access point or whether it should seek a new one. When a node no longer receives acknowledgment from its original access point, it undertakes a new search. Upon finding a new access point, it then re-registers, and the communication process continues.What is ISM band?The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in the hands of users around the globe. What is Spread Spectrum?Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade-off produces a signal that is, in effect, louder and thus easier to detect, provided that
36Appendix A: TroubleshootingFrequently Asked QuestionsWireless-G USB Network Adapter with SRX400the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS).What is DSSS? What is FHSS? And what are their differences?Frequency-Hopping Spread-Spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-Sequence Spread-Spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip (or chipping code). The longer the chip, the greater the probability that the original data can be recovered. Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can recover the original data without the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. Would the information be intercepted while transmitting on air?The Adapter features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum technology, it has the inherent security feature of scrambling. On the software side, the Adapter offers a variety of security methods, including WEP and WPA, to enhance security and access control. For more information, refer to “Appendix C: Wireless Security.”What is WEP?WEP is Wired Equivalent Privacy, a data privacy mechanism based on a shared key algorithm, as described in the IEEE 802.11 standard. For more information, refer to “Appendix C: Wireless Security.”What is WPA?WPA is Wi-Fi Protected Access, a wireless security protocol that can be used in conjunction with a RADIUS server. For more information, refer to “Appendix C: Wireless Security.”What is RADIUS?RADIUS is Remote Authentication Dial-In User Service, which uses an authentication server to control network access. For more information, refer to “Appendix C: Wireless Security.”
37Appendix B: Using Windows XP Wireless Zero ConfigurationWireless-G USB Network Adapter with SRX400Appendix B: Using Windows XP Wireless Zero ConfigurationIf your computer is running Windows XP, then this choice will be available. If you want to use Windows XP Wireless Zero Configuration to control the Adapter, instead of using the Wireless Network Monitor, then right-click on the Wireless Network Monitor and select Use Windows XP Wireless Configuration. If you want to switch back to the Wireless Network Monitor, right-click the Wireless Network Monitor icon, and select Use Linksys Wireless Network Monitor.1. After installing the Adapter, the Windows XP Wireless Zero Configuration icon will appear in your computer’s system tray. Double-click the icon. Figure B-1: Wireless Network Monitor IconFigure B-2: Windows XP - Use Windows XP Wireless ConfigurationNOTE: For more information about Windows XP Wireless Zero Configuration, refer to Windows Help.Figure B-3: Windows XP Wireless Configuration Icon
38Appendix B: Using Windows XP Wireless Zero ConfigurationWireless-G USB Network Adapter with SRX4002. The screen that appears will show any available wireless network. Select the network you want. Click the Connect button.If your network does not have wireless security enabled, go to step 3.If your network does have wireless security enabled, go to step 4.3. If your network does not have wireless security enabled, click the Connect Anyway button to connect the Adapter to your network.NOTE: Steps 2 and 3 are the instructions and screenshots for Windows XP with Service Pack 2 installed.Figure B-4: Available Wireless NetworkFigure B-5: No Wireless Security
39Appendix B: Using Windows XP Wireless Zero ConfigurationWireless-G USB Network Adapter with SRX4004. If your network uses WEP encryption as its wireless security method, enter the WEP Key used in the Network Key and Confirm network key fields. If your network uses WPA Personal for wireless security, enter the Passphrase used in the Network Key and Confirm network key fields. Click the Connect button.5. Your wireless network will appear as Connected when your connection is active.For more information about wireless networking on a Windows XP computer, click the Start button, select Help, and choose Support. Enter the keyword wireless in the field provided, and press the Enter key.You are now connected to your wireless network.NOTE: Windows XP Wireless Configuration does not support the use of a passphrase. Enter the exact WEP key used by your wireless router or access point.Figure B-6: Network Connection - Wireless SecurityFigure B-7: Wireless Network Connection
40Appendix C: Wireless SecuritySecurity PrecautionsWireless-G USB Network Adapter with SRX400Appendix C: Wireless SecurityLinksys wants to make wireless networking as safe and easy for you as possible. The current generation of Linksys products provide several network security features, but they require specific action on your part for implementation. So, keep the following in mind whenever you are setting up or using your wireless network.Security PrecautionsThe following is a complete list of security precautions to take (at least steps 1 through 5 should be followed):1. Change the default SSID. 2. Disable SSID Broadcast. 3. Change the default password for the Administrator account. 4. Enable MAC Address Filtering. 5. Change the SSID periodically. 6. Use the highest encryption algorithm possible. Use WPA if it is available. Please note that this may reduce your network performance. 7. Change the encryption keys periodically. Security Threats Facing Wireless Networks Wireless networks are easy to find. Hackers know that in order to join a wireless network, wireless networking products first listen for “beacon messages”. These messages can be easily decrypted and contain much of the network’s information, such as the network’s SSID (Service Set Identifier). Here are the steps you can take:Change the administrator’s password regularly. With every wireless networking device you use, keep in mind that network settings (SSID, WEP keys, etc.) are stored in its firmware. Your network administrator is the only person who can change network settings. If a hacker gets a hold of the administrator’s password, he, too, can change those settings. So, make it harder for a hacker to get that information. Change the administrator’s password regularly.NOTE: Some of these security features are available only through the network router or access point. Refer to the router or access point’s documentation for more information.
41Appendix C: Wireless SecuritySecurity Threats Facing Wireless NetworksWireless-G USB Network Adapter with SRX400SSID. There are several things to keep in mind about the SSID: 1. Disable Broadcast 2. Make it unique 3. Change it often Most wireless networking devices will give you the option of broadcasting the SSID. While this option may be more convenient, it allows anyone to log into your wireless network. This includes hackers. So, don’t broadcast the SSID.Wireless networking products come with a default SSID set by the factory. (The Linksys default SSID is “linksys”.) Hackers know these defaults and can check these against your network. Change your SSID to something unique and not something related to your company or the networking products you use.Change your SSID regularly so that any hackers who have gained access to your wireless network will have to start from the beginning in trying to break in.MAC Addresses. Enable MAC Address filtering. MAC Address filtering will allow you to provide access to only those wireless nodes with certain MAC Addresses. This makes it harder for a hacker to access your network with a random MAC Address. WEP Encryption. Wired Equivalent Privacy (WEP) is often looked upon as a cure-all for wireless security concerns. This is overstating WEP’s ability. Again, this can only provide enough security to make a hacker’s job more difficult.There are several ways that WEP can be maximized:1. Use the highest level of encryption possible 2. Use “Shared Key” authentication3. Change your WEP key regularly WPA. Wi-Fi Protected Access (WPA) is the newest and best available standard in Wi-Fi security. Four modes are available: WPA-Personal, WPA2-Personal, WPA-Enterprise, and RADIUS. WPA-Personal gives you a choice of two encryption methods: TKIP (Temporal Key Integrity Protocol), which utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers, and AES (Advanced Encryption Standard), which utilizes a symmetric 128-Bit block data encryption. WPA2-Personal only uses AES encryption, which is stronger than TKIP. WPA-Enterprise offers two encryption methods, TKIP and AES, with dynamic encryption keys. RADIUS (Remote Authentication Dial-In User Service) utilizes a RADIUS server for authentication.IMPORTANT: Always remember that each device in your wireless network MUST use the same encryption method and encryption key or your wireless network will not function properly.
42Appendix C: Wireless SecuritySecurity Threats Facing Wireless NetworksWireless-G USB Network Adapter with SRX400WPA-Personal. If you do not have a RADIUS server, select the type of algorithm you want to use, TKIP or AES, and enter a password in the Passphrase field of 8-63 characters.WPA2-Personal. Enter a password in the Passphrase field of 8-63 characters.WPA-Enterprise. WPA used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.) WPA-Enterprise offers two encryption methods, TKIP and AES, with dynamic encryption keys. Enter the RADIUS server’s IP Address and port number, along with a key shared between the device and the server. Last, enter a Group Key Renewal period, which instructs the device how often it should change the encryption keys.RADIUS. WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router or other device.) First, enter the RADIUS server’s IP Address and port number, along with a key shared between the device and the server. Then, select a WEP key and a level of WEP encryption, and either generate a WEP key through the Passphrase or enter the WEP key manually.Implementing encryption may have a negative impact on your network’s performance, but if you are transmitting sensitive data over your network, encryption should be used. These security recommendations should help keep your mind at ease while you are enjoying the most flexible and convenient technology Linksys has to offer.
43Appendix D: Windows HelpWireless-G USB Network Adapter with SRX400Appendix D: Windows HelpAlmost all wireless products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix.TCP/IPBefore a computer can communicate with an access point or wireless router, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network. This is true for wireless networks as well. Your PCs will not be able to utilize wireless networking without having TCP/IP enabled. Windows Help provides complete instructions on enabling TCP/IP.Shared ResourcesIf you wish to share printers, folder, or files over your network, Windows Help provides complete instructions on utilizing shared resources.Network Neighborhood/My Network PlacesOther PCs on your network will appear under Network Neighborhood or My Network Places (depending upon the version of Windows you're running). Windows Help provides complete instructions on adding PCs to your network.
44Appendix E: GlossaryWireless-G USB Network Adapter with SRX400Appendix E: GlossaryThis glossary contains some basic networking terms you may come across when using this product. For more advanced terms, see the complete Linksys glossary at http://www.linksys.com/glossary.Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network.Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access point.AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption.Bandwidth - The transmission capacity of a given device or network.Bit - A binary digit.Boot - To start a device and cause it to start executing instructions.Broadband - An always-on, fast Internet connection.Browser - An application program that provides a way to look at and interact with all the information on the World Wide Web. Byte - A unit of data that is usually eight bits longCable Modem - A device that connects a computer to the cable television network, which in turn connects to the Internet.Daisy Chain - A method used to connect devices in a series, one after the other.DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (e.g., www.xyz.com) and a dynamic IP address.Default Gateway - A device that forwards Internet traffic from your local area network.DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign temporary IP addresses to network computers by "leasing" an IP address to a user for a limited amount of time, instead of assigning permanent IP addresses.
45Appendix E: GlossaryWireless-G USB Network Adapter with SRX400DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be "seen" from the Internet.DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses.Domain - A specific name for a network of computers.Download - To receive a file transmitted over a network. DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines.Dynamic IP Address - A temporary IP address assigned by a DHCP server.EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access. Many specific authentication methods work within this framework.Encryption - Encoding data transmitted in a network. Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium.Firewall - A set of related programs located at a network gateway server that protects the resources of a network from users from other networks.Firmware - The programming code that runs a networking device.FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network.Full Duplex - The ability of a networking device to receive and transmit data simultaneously.Gateway - A device that interconnects networks with different, incompatible communications protocols. Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a time.HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World Wide Web.Infrastructure - A wireless network that is bridged to a wired network via an access point.IP (Internet Protocol) - A protocol used to send data over a network.
46Appendix E: GlossaryWireless-G USB Network Adapter with SRX400IP Address - The address used to identify a computer or device on a network.IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device.IPSec (Internet Protocol Security) - A VPN protocol used to implement secure exchange of packets at the IP layer.ISP (Internet Service Provider) - A company that provides access to the Internet. LAN - The computers and networking products that make up your local network.MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking device. Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet.Network - A series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users.Packet - A unit of data sent over a network.Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products.Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.POP3 (Post Office Protocol 3) - A standard mail server commonly used on the Internet.Port - The connection point on a computer or networking device used for plugging in cables or adapters. Power over Ethernet (PoE) - A technology enabling an Ethernet network cable to deliver both data and power.PPPoE (Point to Point Protocol over Ethernet) - A type of broadband connection that provides authentication (username and password) in addition to data transport.PPTP (Point-to-Point Tunneling Protocol) - A VPN protocol that allows the Point to Point Protocol (PPP) to be tunneled through an IP network. This protocol is also used as a type of broadband connection in Europe.RADIUS (Remote Authentication Dial-In User Service) - A protocol that uses an authentication server to control network access.
47Appendix E: GlossaryWireless-G USB Network Adapter with SRX400RJ-45 (Registered Jack-45) - An Ethernet connector that holds up to eight wires.Roaming - The ability to take a wireless device from one access point's range to another without losing the connection.Router - A networking device that connects multiple networks together.Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet.SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol.SPI (Stateful Packet Inspection) Firewall - A technology that inspects incoming packets of information before allowing them to enter the network.SSID (Service Set IDentifier) - Your wireless network's name.Static IP Address - A fixed address assigned to a computer or device that is connected to a network.Static Routing - Forwarding data in a network via a fixed path.Subnet Mask - An address code that determines the size of the network.Switch - 1. A data switch that connects computing devices to host computers, allowing a large number of devices to share a limited number of ports. 2. A device for making, breaking, or changing the connections in an electrical circuit. TCP (Transmission Control Protocol) - A network protocol for transmitting data that requires acknowledgement from the recipient of data sent.TCP/IP (Transmission Control Protocol/Internet Protocol) - A set of instructions PCs use to communicate over a network.Telnet - A user command and TCP/IP protocol used for accessing remote PCs.TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol that has no directory or password capability.Throughput - The amount of data moved successfully from one node to another in a given time period.
48Appendix E: GlossaryWireless-G USB Network Adapter with SRX400TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted.Topology - The physical layout of a network.TX Rate - Transmission Rate.Upgrade - To replace existing software or firmware with a newer version. Upload - To transmit a file over a network.URL (Uniform Resource Locator) - The address of a file located on the Internet. VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another over the Internet.WAN (Wide Area Network)- The Internet.WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for greater security.WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with each other wirelessly.WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.
49Appendix F: SpecificationsWireless-G USB Network Adapter with SRX400Appendix F: SpecificationsModel WUSB54GX4Standards 802.11g, 802.11bLEDs Link, Act# of Antennas TwoRF Pwr (EIRP) in dBm 17 dBm (b), 14 dBm (g)Security Features WPA, WPA2 WEP, and 802.1xWEP Key Bits 64/128bitDimensions 4.53" x 3.15" x 0.79" (115 mm x 80 mm x 20 mm)Unit Weight 2.7 oz. (0.077 kg)Power 3.3V ± 5%Certifications FCC, CE, ICES-003, Wi-Fi, WHQLOperating Temp. 0° C to 60° C (32° F to 140° F)Storage Temp. -20° C to 85° C (-4° F to 185° F)Operating Humidity Max. 90% Non-CondensingStorage Humidity 5% to 90% Non-Condensing17 dBm (g)
50Appendix G: Warranty InformationWireless-G USB Network Adapter with SRX400Appendix G: Warranty InformationLIMITED WARRANTYLinksys warrants to You that, for a period of three years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys' entire liability under this warranty will be for Linksys at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser. If the Product proves defective during the Warranty Period call Linksys Technical Support in order to obtain a Return Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You are responsible for shipping defective Products to Linksys. Linksys pays for UPS Ground shipping from Linksys back to You only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling charges. ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives You specific legal rights, and You may also have other rights which vary by jurisdiction.This warranty does not apply if the Product (a) has been altered, except by Linksys, (b) has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, or (c) has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the Product will be free of vulnerability to intrusion or attack.TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You.Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.
51Appendix H: Regulatory InformationWireless-G USB Network Adapter with SRX400Appendix H: Regulatory InformationFCC StatementThis product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna• Increase the separation between the equipment or devices• Connect the equipment to an outlet other than the receiver's• Consult a dealer or an experienced radio/TV technician for assistanceFCC Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.Safety NoticesCaution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.Do not use this product near water, for example, in a wet basement or near a swimming pool.Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.Industry Canada (Canada)This device complies with Canadian ICES-003 and RSS210 rules.Cet appareil est conforme aux normes NMB-003 et RSS210 d'Industry Canada.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE:
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Linksys declares that WUSB54GX4 (FCC ID: Q87-WUSB54GX4) is limited in CH1~CH11 for 2.4 GHz by specified firmware controlled in U.S.A.
52Appendix H: Regulatory InformationWireless-G USB Network Adapter with SRX400User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE)This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:
53Appendix H: Regulatory InformationWireless-G USB Network Adapter with SRX400
54Appendix H: Regulatory InformationWireless-G USB Network Adapter with SRX400
55Appendix H: Regulatory InformationWireless-G USB Network Adapter with SRX400
56Appendix H: Regulatory InformationWireless-G USB Network Adapter with SRX400For more information, visit www.linksys.com.
57Appendix I: Contact InformationWireless-G USB Network Adapter with SRX400Appendix I: Contact InformationNeed to contact Linksys?Visit us online for information on the latest products and updates to your existing products at: http://www.linksys.com or ftp.linksys.comCan't find information about a product you want to buyon the web? Do you want to know more about networkingwith Linksys products? Give our advice line a call at: 800-546-5797 (LINKSYS)Or fax your request in to: 949-823-3002If you experience problems with any Linksys product,you can call us at: 800-326-7114Don't wish to call? You can e-mail us at: support@linksys.comIf any Linksys product proves defective during its warranty period,you can call the Linksys Return Merchandise Authorizationdepartment for obtaining a Return Authorization Number at: 949-823-3000(Details on Warranty and RMA issues can be found in the WarrantyInformation section in this Guide.)

Navigation menu