LINKSYS WUSBF54G Wireless-G USB Adapter with Wi-Fi Finder User Manual Book

LINKSYS LLC Wireless-G USB Adapter with Wi-Fi Finder Book

Contents

Users Manual 1

A Division of Cisco Systems, Inc.®Model No.USB Network AdapterWireless-GWUSBF54GUser GuideWIRELESSGHz2.4802.11gwith Wi-Fi Finder
Wireless-G USB Network Adapter with Wi-Fi FinderCopyright and TrademarksSpecifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.How to Use this User GuideThis User Guide has been designed to make understanding networking with the Wireless-G USB Network Adapter with Wi-Fi Finder easier than ever. Look for the following items when reading this User Guide:In addition to these symbols, there are definitions for technical terms that are presented like this:Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this:Figure numbers and descriptions can also be found in the "List of Figures" section in the “Table of Contents”. This exclamation point means there is a Caution or warning and is something that could damage your property or the Wireless-G USB Network Adapter with Wi-Fi Finder.This checkmark means there is a Note of interest and is something you should pay special attention to while using the Wireless-G USB Network Adapter with Wi-Fi Finder.This question mark provides you with a reminder about something you might need to do while using the Wireless-G USB Network Adapter with Wi-Fi Finder.word: definition.Figure 0-1: Sample Figure DescriptionWUSBF54G-UG-50810NC BWWARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
Wireless-G USB Network Adapter with Wi-Fi FinderTable of ContentsChapter 1: Introduction 1Welcome 1What’s in this Guide? 2Chapter 2: Planning your Wireless Network 4Network Topology 4Roaming 4Network Layout 5Chapter 3: Getting to Know and Using the Wireless-G Network Adapter with Wi-Fi Finder 6The Front Panel 6Using the Wi-Fi Finder 7The Side Panels 8Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi Finder 9Starting the Setup Wizard 9Connecting the Adapter 10Setting Up the Adapter 10Chapter 5: Using the Wireless Network Monitor 20Accessing the Wireless Network Monitor 20Link Information Screens 20Site Survey 23Profiles 24Creating a New Profile 25Appendix A: Troubleshooting 35Common Problems and Solutions 35Frequently Asked Questions 36Appendix B: Using Windows XP Wireless Configuration 39Appendix C: Wireless Security 42Security Precautions 42Security Threats Facing Wireless Networks 42Appendix D: Windows Help 45
Wireless-G USB Network Adapter with Wi-Fi FinderAppendix E: Glossary 46Appendix F: Specifications 53Appendix G: Warranty Information 54Appendix H: Regulatory Information 55Appendix I: Contact Information 57
Wireless-G USB Network Adapter with Wi-Fi FinderList of FiguresFigure 3-1: Front Panel 6Figure 3-2: Wi-Fi Finder’s Wireless Network Screen 7Figure 3-3: Wi-Fi Finder’s ON/OFF Switch and Buttons 8Figure 4-1: Setup Wizard’s Welcome Screen 9Figure 4-2: Setup Wizard’s License Agreement 9Figure 4-3: The Connecting the Adapter Screen 10Figure 4-4: Available Wireless Network 10Figure 4-5: Available Wireless Network 11Figure 4-6: Wireless Security - WEP 11Figure 4-7: Wireless Security - WPA Personal 12Figure 4-8: Congratulations 12Figure 4-9: Available Wireless Network 13Figure 4-10: Network Settings 13Figure 4-11: Wireless Mode 14Figure 4-12: Ad-Hoc Mode Settings 14Figure 4-13: Wireless Security 15Figure 4-14: Wireless Security - WEP 15Figure 4-15: Wireless Security - WPA Personal 16Figure 4-16: Wireless Security - WPA Enterprise - EAP-TLS 17Figure 4-17: Wireless Security - WPA Enterprise - PEAP 17Figure 4-18: Wireless Security - RADIUS - EAP-TLS 18Figure 4-19: Wireless Security - RADIUS - PEAP 18Figure 4-20: Confirm New Settings 19Figure 4-21: Congratulations 19Figure 5-1: Wireless Network Monitor Icon 20Figure 5-2: Link Information 20Figure 5-3: More Information - Wireless Network Status 21Figure 5-4: More Information - Wireless Network Statistics 22Figure 5-5: Site Survey 23Figure 5-6: WEP Key Needed for Connection 23
Wireless-G USB Network Adapter with Wi-Fi FinderFigure 5-7: WPA-Personal Needed for Connection 23Figure 5-8: Profiles 24Figure 5-9: Import a Profile 24Figure 5-10: Export a Profile 24Figure 5-11: Create a New Profile 25Figure 5-12: Available Wireless Network 25Figure 5-13: Available Wireless Network 26Figure 5-14: WEP Key Needed for Connection 26Figure 5-15: WPA-Personal Needed for Connection 27Figure 5-16: The Congratulations Screen 27Figure 5-17: Available Wireless Network 28Figure 5-18: Network Settings 28Figure 5-19: Wireless Mode 29Figure 5-20: Ad-Hoc Mode Settings 29Figure 5-21: Wireless Security 30Figure 5-22: Wireless Security - WEP 30Figure 5-23: Wireless Security - WPA Personal 31Figure 5-24: Wireless Security - WPA Enterprise - EAP-TLS 32Figure 5-25: Wireless Security - WPA Enterprise - PEAP 32Figure 5-26: Wireless Security - RADIUS - EAP-TLS 33Figure 5-27: Wireless Security - RADIUS - PEAP 33Figure 5-28: Confirm New Settings 34Figure 5-29: The Congratulations Screen 34Figure B-1: Wireless Network Monitor Icon 39Figure B-2: Windows XP - Use Windows XP Wireless Configuration 39Figure B-3: Windows XP Wireless Configuration Icon 39Figure B-4: Available Wireless Network 40Figure B-5: No Wireless Security 40Figure B-6: Network Connection - Wireless Security 41Figure B-7: Wireless Network Connection 41
1Chapter 1: IntroductionWelcomeWireless-G USB Network Adapter with Wi-Fi FinderChapter 1: IntroductionWelcomeThank you for choosing the Wireless-G USB Network Adapter with Wi-Fi Finder. With this Adapter, your wireless networking experience will be faster and easier than ever.How does the Adapter do this? Like all wireless products, the Adapter allows for greater range and mobility within your wireless network. Connecting to your PC via the USB port means that this Adapter leaves the PC’s slots open for other purposes. This adapter communicates over the 802.11g wireless standard, one of the newest wireless standards, to communicate with your network. It also has a convenient Wi-Fi Finder that enables you to find an available wireless network to connect to with just a click of a button.But what does all of this mean? Networks are useful tools for sharing computer resources. You can access one printer from different computers and access data located on another computer's hard drive. Networks are even used for playing multiplayer video games. So, networks are not only useful in homes and offices, they can also be fun.PCs equipped with wireless cards and adapters can communicate without cumbersome cables. By sharing the same wireless settings, within their transmission radius, they form a wireless network. Use the instructions in this Guide to help you connect the Adapter, set it up, and configure it for your network. These instructions should be all you need to get the most out of the Adapter. 802.11g: an IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices.adapter: a device that adds network functionality to your PC. network: a series of computers or devices connected for the purpose of data sharing, storage, and/or transmission between users.
2Chapter 1: IntroductionWhat’s in this Guide?Wireless-G USB Network Adapter with Wi-Fi FinderWhat’s in this Guide?This user guide covers the steps for setting up and using the Wireless-G USB Network Adapter with Wi-Fi Finder.• Chapter 1: IntroductionThis chapter describes the Adapter’s applications and this User Guide.• Chapter 2: Planning Your Wireless NetworkThis chapter discusses a few of the basics about wireless networking.• Chapter 3: Setting Up and Connecting the Wireless-G USB Network Adapter with Wi-Fi Finder.This chapter shows you how to setup and connect the Adapter.• Chapter 4: Using the Wireless Network Monitor This chapter show you how to use the Adapter’s Wireless Network Monitor.• Appendix A: TroubleshootingThis appendix describes some problems and solutions, as well as frequently asked questions, regarding installation and use of the Adapter.• Appendix B: Using Windows XP Wireless ConfigurationThis appendix describes how Windows XP users can use Window’s built-in wireless configuration to monitor their Adapter.• Appendix C: Wireless SecurityThis appendix discusses security issues regarding wireless networking and measures you can take to help protect your wireless network.• Appendix D: Windows HelpThis appendix describes how you can use Windows Help for instructions about networking, such as installing the TCP/IP protocol.• Appendix E: GlossaryThis appendix gives a brief glossary of terms frequently used in networking.• Appendix F: SpecificationsThis appendix provides the Adapter’s technical specifications.• Appendix G: Warranty InformationThis appendix supplies the Adapter’s warranty information.
3Chapter 1: IntroductionWhat’s in this Guide?Wireless-G USB Network Adapter with Wi-Fi Finder• Appendix H: Regulatory InformationThis appendix supplies the Adapter’s regulatory information.• Appendix I: Contact InformationThis appendix provides contact information for a variety of Linksys resources, including Technical Support.
4Chapter 2: Planning your Wireless NetworkNetwork TopologyWireless-G USB Network Adapter with Wi-Fi FinderChapter 2: Planning your Wireless NetworkNetwork TopologyA wireless network is a group of computers, each equipped with one wireless adapter.  Computers in a wireless network must be configured to share the same radio channel. Several PCs equipped with wireless cards or adapters can communicate with one another to form an ad-hoc network.Linksys wireless adapters also provide users access to a wired network when using an access point or wireless router.  An integrated wireless and wired network is called an infrastructure network. Each wireless PC in an infrastructure network can talk to any computer in a wired network infrastructure via the access point or wireless router.An infrastructure configuration extends the accessibility of a wireless PC to a wired network, and can double the effective wireless transmission range for two wireless adapter PCs.  Since an access point is able to forward data within a network, the effective transmission range in an infrastructure network can be doubled.RoamingInfrastructure mode also supports roaming capabilities for mobile users. Roaming means that you can move your wireless PC within your network and the access points will pick up the wireless PC's signal, providing that they both share the same channel and SSID.Before enabling you consider roaming, choose a feasible radio channel and optimum access point position. Proper access point positioning combined with a clear radio signal will greatly enhance performance.access point: device that allows wireless-equipped computers and other devices to communicate with a wired network.ad-hoc: a group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access pointinfrastructure: Configuration in which a wireless network is bridged to a wired network via an access point.roaming: the ability to take a wireless device from one access point's range to another without losing the connection. ssid: your wireless network’s name
5Chapter 2: Planning your Wireless NetworkNetwork LayoutWireless-G USB Network Adapter with Wi-Fi FinderNetwork LayoutLinksys wireless access points and wireless routers have been designed for use with 802.11a, 802.11b, and 802.11g products. With 802.11g products communicating with the 802.11b standard and some products incorporating both “a” and “g”, products using these standards can communicate with each other.Access points and wireless routers are compatible with 802.11a, 802.11b and 802.11g adapters, such at the PC Cards for your laptop computers, PCI Card for your desktop PC, and USB Adapters for when you want to enjoy USB connectivity. Wireless products will also communicate with the wireless PrintServer.When you wish to connect your wired network with your wireless network, network ports on access points and wireless routers can be connected to any of Linksys's switches or routers.With these, and many other, Linksys products, your networking options are limitless. Go to the Linksys website at www.linksys.com for more information about wireless products. 802.11g: an IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an operating frequency of 2.4GHz. It is backward compatibility with 802.11b devices.switch: device that is the central point of connection for computers and other devices in a network, so data can be shared at full transmission speeds.router: a networking device that connects multiple networks together, such as a local network and the Internet.802.11b: A wireless networking standard that specifies a maximum data transfer rate of 11Mbps and an operating frequency of 2.4GHz.802.11a: A wireless networking standard that specifies a maximum data transfer rate of 54Mbps and an operating frequency of 5GHz.
6Chapter 3: Getting to Know and Using the Wireless-G Network Adapter with Wi-Fi FinderThe Front PanelWireless-G USB Network Adapter with Wi-Fi FinderChapter 3: Getting to Know and Using the Wireless-G Network Adapter with Wi-Fi FinderThe Front PanelThe Network Adapter's LEDs and Wi-Fi Finder LCD screen are located on the Front Panel.LEDsPower Green. The Power LED lights up when the Adapter is powered on.Link Green. The Link LED lights up when there is wireless activity. Figure 3-1: Front PanelPower LEDLink LEDWi-Fi Finder’s Wireless Network Screen USB Connector
7Chapter 3: Getting to Know and Using the Wireless-G Network Adapter with Wi-Fi FinderUsing the Wi-Fi FinderWireless-G USB Network Adapter with Wi-Fi FinderUsing the Wi-Fi FinderFigure 3-2: Wi-Fi Finder’s Wireless Network ScreenWireless Network Name (SSID)Channel (1-11) Wireless Network Scan Modes A = All U = UnsecuredS = Specific Network NameNumber of Available Wireless Networks (maximum of 15)Wireless Network’s Security Status(Secured or Unsecured)Wireless ModeB = 802.11bG = 802.11gBattery Power Status Low or Normal (Normal shown, Low is displayed as small amount of black)Signal Strength
8Chapter 3: Getting to Know and Using the Wireless-G Network Adapter with Wi-Fi FinderUsing the Wi-Fi FinderWireless-G USB Network Adapter with Wi-Fi FinderON/OFF Switch  The ON/OFF switch is located on the side panel. Slide the button to the right side to turn on the Wi-Fi Finder.Scan The Scan button is located on the side panel. Push the Scan button to scan for a wireless network.There are three Wireless Network Scan Modes (shown in bottom right corner of screen): A = All Networks (default mode), U = Unsecured Networks, S = Specific Network NameTo change the mode, push and hold the Scan button. • All Networks: This default mode scans and displays all secure and unsecure networks. • Unsecured Networks: This mode scans and displays only unsecured networks.• Specific Network Name: This mode scans and displays any networks with a selected specific network name. First, while in the All Networks mode, use the Scroll button and scroll until the network that you want is on your screen, then push and hold the Scan button to change the icon to S. Then, push the Scan button again to scan for any network with the selected name.Scroll The Scroll button is located on the side panel. Push the Scroll button to view the next available wireless network, which will be displayed in the order of strongest to weakest signal strength. A maximum of fifteen wireless networks can be viewed. Figure 3-3: Wi-Fi Finder’s ON/OFF Switch and Buttons
9Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderStarting the Setup WizardWireless-G USB Network Adapter with Wi-Fi FinderChapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderThe Wireless-G USB Network Adapter with Wi-Fi Finder is set up with the Setup Wizard that comes on the CD enclosed with the Adapter. This chapter will guide you through the setup procedure. Starting the Setup WizardTo begin the setup process, insert the Setup Wizard CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the Welcome screen should appear.  If it does not, click the Start button and choose Run. In the field that appears, enter D:\setup.exe (if “D” is the letter of your CD-ROM drive). On the Welcome screen, you have the following choices:Click Here to Start - Click the Click Here to Start button to begin the software installation process. User Guide - Click the User Guide button to open this User Guide. Exit - Click Exit to exit the Setup Wizard.1. To install the Adapter, click the Click Here to Start button on the Welcome screen.2. After reading the License Agreement, click Next if you agree and want to continue the installation, or click Cancel to end the installation.Figure 4-1: Setup Wizard’s Welcome ScreenFigure 4-2: Setup Wizard’s License AgreementIMPORTANT: Do not connect the Adapter until you are instructed to do so or the setup will not work.
10Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderConnecting the AdapterWireless-G USB Network Adapter with Wi-Fi Finder3. Windows will begin copying the files onto your PC.4. The Setup Wizard will now prompt you to connect the Adapter to your PC’s USB port. Once you’ve connected, click Next.5. If prompted by Windows, Windows 98SE and ME users will need to restart their PCs. Connecting the Adapter 1. Insert the USB connector end of the Adapter into the USB port of the PC. 2. The Power LED should light up when the Adapter is plugged in.Setting Up the AdapterThe next screen to appear will be the Available Wireless Network screen.This screen provides two options for setting up the Adapter•Available Wireless Network. (For most users.) Use this option if you have already set up a network and the network is listed on the screen. Select the network and click the Connect button to connect to it. If you need to update the Available Wireless Network list, click the Refresh button. •Manual Setup. If your network is not listed on this screen, select Manual Setup to set up the Adapter manually. This method of setting up the Adapter is intended for Advanced Users only.The setup for each option is described, step by step, under the appropriate heading on the following pages.Click Exit to close the Setup Wizard, if you wish to set up the Adapter later.Figure 4-3: The Connecting the Adapter ScreenFigure 4-4: Available Wireless Network
11Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderSetting Up the AdapterWireless-G USB Network Adapter with Wi-Fi FinderSetting Up the Adapter with Available NetworksThe available networks are listed in the table on the center of the screen by SSID. Select the wireless network you wish to connect to and click the Connect button. (If you do not see your network listed, you can click the Refresh button to bring the list up again.) If the network utilizes wireless security, you will need to configure security on the Adapter. If not, you will be taken directly to the Congratulations screen.1. If wireless security has been enabled on this network, you will see a wireless security screen. If your network utilizes WEP (Wired Equivalent Privacy) encryption, the WEP Key Needed for Connection screen will appear. If your network utilizes WPA-Personal (Wi-Fi Protected Access) encryption, the WPA-Personal Needed for Connection screen will appear. WEP Key Needed for ConnectionSelect 64-bit or 128-bit. Then, enter a passphrase or WEP key.Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption, enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel.Figure 4-5: Available Wireless NetworkFigure 4-6: Wireless Security - WEP
12Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderSetting Up the AdapterWireless-G USB Network Adapter with Wi-Fi FinderWPA-Personal Needed for ConnectionEncryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. The passphrase must match the devices on your wireless network.Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel.2. After the Adapter has been configured for the network, the Congratulations screen will appear. Click Connect to Network to connect to your network.Congratulations! Setup is complete.To check the link information, search for available wireless networks, or make additional configuration changes, refer to Chapter 5: Using the Wireless Network MonitorFigure 4-7: Wireless Security - WPA PersonalFigure 4-8: Congratulations
13Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderSetting Up the AdapterWireless-G USB Network Adapter with Wi-Fi FinderSetting Up the Adapter with Manual SetupIf your network is not listed with the available networks, click Manual Setup on the Available Wireless Network screen to set up the Adapter manually. 1. After clicking Manual Setup, the Network Settings screen will appear. If your network has a router or other DHCP server, click the radio button next to Obtain network settings automatically (DHCP).If your network does not have a Router or DHCP server, click the radio button next to Specify network settings. Enter an IP Address, Subnet Mask, Default Gateway, and DNS addresses appropriate for your network. You must specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and DNS addresses, leave these fields empty. IP Address - This IP Address must be unique to your network.Subnet Mask - The Adapter’s Subnet Mask must be the same as your wired network’s Subnet Mask.Default Gateway - Enter the IP address of your network’s Gateway here. DNS 1 and DNS 2 - Enter the DNS address of your wired Ethernet network here.Click Next to continue, or click Back to return to the Available Wireless Network screen.Figure 4-9: Available Wireless NetworkFigure 4-10: Network Settings
14Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderSetting Up the AdapterWireless-G USB Network Adapter with Wi-Fi Finder 2. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio button if you want to connect to a wireless router or access point. Click the Ad-Hoc Mode radio button if you want to connect to another wireless device directly without using a wireless router or access point. Then, enter the SSID for your network.Infrastructure Mode - Use this mode if you want to connect to a wireless router or access point.Ad-Hoc Mode - Use this mode if you want to connect to another wireless device directly without using a wireless router or access point.SSID - This is the wireless network name that must be used for all the devices in your wireless network. It is case- sensitive and should be a unique name to help prevent others from entering your network.Click Next to continue or Back to return to the previous screen. 3. If you chose Infrastructure Mode, go to Step 4 now. If you chose Ad-Hoc Mode, the Ad-Hoc Mode Settings screen will appear.Select the correct Channel for your wireless network. The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which channel to use, keep the default setting.Then, select the Network Mode in which your wireless network will operate. In Mixed Mode, Wireless-B and Wireless-G devices can both operate on the network, though at a slower speed. In G-Only Mode, no Wireless-B devices can operate in the network.Click Next to continue or click Back to change any settings.Figure 4-11: Wireless ModeFigure 4-12: Ad-Hoc Mode Settings
15Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderSetting Up the AdapterWireless-G USB Network Adapter with Wi-Fi Finder 4. The Wireless Security screen will appear. This step will configure wireless security.If your wireless network doesn’t use wireless security, select Disabled and then click the Next button to continue. Proceed to Step 5.Select WEP, WPA-Personal, WPA-Enterprise, or Radius for the Encryption Method. WEP stands for Wired Equivalent Privacy, WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption, and RADIUS stands for Remote Authentication Dial-In User Service. If you don’t want to use encryption, select Disabled. Then, click the Next button to continue or the Back button to return to the previous screen. WEP WEP - To use WEP encryption, select 64-bits or 128-bit characters from the drop-down menu, and enter a passphrase or key.WEP Key- The WEP key you enter must match the WEP key of your wireless network. If you are using 64-bit WEP encryption, then the key must consist of exactly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Passphrase - Instead of manually entering a WEP key, you can enter a passphrase in the Passphrase field, so a WEP key is automatically generated. This case-sensitive passphrase must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)TX Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit key number 2, 3, or 4, select the appropriate number from the TX Key drop-down box.Authentication -The default is set to Auto, where it auto-detects for Shared Key or Open systemNetshared Key is when both the sender and the recipient share a WEP key for authentication. Open key is when the sender and the recipient do not share a WEP key for authentication. All points on your network must use the same authentication type.Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen. Figure 4-13: Wireless Securityencryption: encoding data transmitted in a network.Figure 4-14: Wireless Security - WEPwep (wired equivalent privacy): a method of encrypting network data transmitted on a wireless network for greater security.
16Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderSetting Up the AdapterWireless-G USB Network Adapter with Wi-Fi FinderWPA PersonalWPA Personal offers two encryption methods, TKIP and AES, with dynamic encryption keys. Select TKIP or AES for encryption. Then enter a Passphrase that is 8-63 characters in length.Encryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. The passphrase must match the devices on your wireless network.Click the Next button to continue or the Back button to return to the previous screen.Figure 4-15: Wireless Security - WPA Personal
17Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderSetting Up the AdapterWireless-G USB Network Adapter with Wi-Fi FinderWPA EnterpriseWPA Enterprise features WPA security used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) WPA Enterprise offers two authentication methods, EAP-TLS and PEAP, as well as two encryption methods, TKIP and AES, with dynamic encryption keys.Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.EAP-TLSIf you selected EAP-TLS, enter the login name of your wireless network in the Login Name field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network. Select the type of encryption, TKIP or AES, from the Encryption drop-down menu.Click the Next button to continue or the Back button to return to the previous screen.PEAPIf you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the password of your wireless network in the Password field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network; if you want to use any certificate, keep the default setting, Trust Any. Then select the authentication method (Inner Authen.) used inside the PEAP tunnel. Select EAP-MSCHAP v2. Then, select the type of encryption, TKIP or AES, from the Encryption drop-down menu.Click the Next button to continue or the Back button to return to the previous screen.Figure 4-17: Wireless Security - WPA Enterprise - PEAPFigure 4-16: Wireless Security - WPA Enterprise - EAP-TLS
18Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderSetting Up the AdapterWireless-G USB Network Adapter with Wi-Fi FinderRADIUSRADIUS uses the security of a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) It offers two authentication methods: EAP-TLS and PEAP.Authentication - Select the authentication method your network is using, EAP-TLS or PEAP.EAP-TLSEnter the Login name of your wireless network in the Login Name field. From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network. PEAPIf you selected PEAP, enter the login name of your wireless network in the Login Name field. Enter the password of your wireless network in the Password field. Enter the name of the authentication server in the Server Name field (this is optional). From the Certificate drop-down menu, select the certificate you have installed to authenticate you on your wireless network; if you want to use any certificate, keep the default setting, Trust Any. Then select the authentication method (Inner Authen.) used inside the PEAP tunnel. Select EAP-MSCHAP v2. Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen. Figure 4-18: Wireless Security - RADIUS - EAP-TLSFigure 4-19: Wireless Security - RADIUS - PEAP
19Chapter 4: Setting up and Connecting the Wireless-G USB Network Adapter with Wi-Fi FinderSetting Up the AdapterWireless-G USB Network Adapter with Wi-Fi Finder 5. The next screen displays all of the Adapter’s settings. If these are correct, you can save these settings to your hard drive by clicking Save. Click Next to continue and finish the setup. If these settings are not correct, click Back to change your settings. To exit the setup, click Exit. 6. After the software has been successfully installed, the Congratulations screen will appear. Click Connect to Network to connect to your network. Clicking Return to Profiles screen will open the Wireless Network Monitor’s Profiles screen. For more information about the Wireless Network Monitor, refer to Chapter 5: Using the Wireless Network Monitor.Congratulations! Setup is complete.To check the link information, search for available wireless networks, or make additional configuration changes, refer to Chapter 5: Using the Wireless Network Monitor.Figure 4-20: Confirm New SettingsFigure 4-21: Congratulations
20Chapter 5: Using the Wireless Network MonitorAccessing the Wireless Network MonitorWireless-G USB Network Adapter with Wi-Fi FinderChapter 5: Using the Wireless Network MonitorUse the Wireless Network Monitor to check the link information, search for available wireless networks, or create profiles that hold different configuration settings.Accessing the Wireless Network MonitorAfter setting up and connecting the Adapter, the Wireless Network Monitor icon will appear in your PC’s system tray. If the Wireless Network Monitor is enabled, then the icon will be green. If the Wireless Network Monitor is disabled or the Adapter is not connected, then the icon will be gray.Link Information ScreensThe opening screen of the Wireless Network Monitor is the Link Information screen. From this screen, you can find out how strong the current wireless signal is and how good the connection’s quality is. You can also click the More Information button to view additional status and statistics about the current wireless connection. To search for available wireless networks, click the Site Survey tab. To perform configuration changes or create connection profiles, click the Profiles tab.Link InformationThe Link Information screen displays network mode, signal strength, and link quality information about the current connection. It also provides a button to click for additional status information.Ad-Hoc Mode or Infrastructure Mode - The screen indicates whether the Adapter is currently working in Ad-Hoc or Infrastructure mode.Signal Strength - The Signal Strength bar indicates signal strength. Link Quality - The Link Quality bar indicates the quality of the wireless network connection.Click the More Information button to view additional information about the wireless network connection on the Wireless Network Status screen.Figure 5-1: Wireless Network Monitor IconFigure 5-2: Link InformationNOTE: The Wireless Network Monitor should only be accessed AFTER connecting the Adapter. For more information on Setting Up and Connecting the Adapter, refer to Chapter 4: Setting Up and Connecting the USB Network Adapter.
21Chapter 5: Using the Wireless Network MonitorLink Information ScreensWireless-G USB Network Adapter with Wi-Fi FinderWireless Network StatusThe Wireless Network Status screen provides information on your current network settings.Status - This shows the status of the wireless network connection.SSID - This is the unique name of the wireless network. Wireless Mode - The mode of the wireless network currently in use is displayed here.Transfer Rate - The data transfer rate of the current connection is shown here.Channel - This is the channel to which the wireless network devices are set. Security - The status of the wireless security feature is displayed here.Authentication - This is your wireless network’s authentication method.IP Address - The IP Address of the Adapter is displayed here.Subnet Mask - The Subnet Mask of the Adapter is shown here.Default Gateway - The Default Gateway address of the Adapter is displayed here.DNS - This is the DNS address of the Adapter.DHCP Client - This displays the Adapter’s status as a DHCP client.MAC Address- The MAC address of the wireless network’s access point or wireless router is shown here.Signal Strength - The Signal Strength bar indicates the signal strength. Link Quality - The Link Quality bar indicates the quality of the wireless network connection.Click the Back button to return to the initial Link Information screen. Click the Statistics button to go to the Wireless Network Statistics screen. Click the Save to Profile button to save the currently active connection settings to a profile.Figure 5-3: More Information - Wireless Network Status
22Chapter 5: Using the Wireless Network MonitorLink Information ScreensWireless-G USB Network Adapter with Wi-Fi FinderWireless Network StatisticsThe Wireless Networks Statistics screen provides statistics on your current network settings.Transmit Rate - This is the data transfer rate of the current connection. (In Auto mode, the Adapter dynamically shifts to the fastest data transfer rate possible at any given time.)Receive Rate - This is the rate at which data is received.Packets Received - This shows the packets received by the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Packets Transmitted - This shows the packets transmitted from the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Bytes Received - This shows the bytes received by the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Bytes Transmitted - This shows the bytes transmitted by the Adapter, in real time, since connecting to the wireless network or since the Refresh Statistics button was last pressed.Driver Version - This shows the version of the Adapter’s driver.Noise Level - This shows the level of background noise affecting the wireless signal. A lower reading translates into a higher quality signal.Signal Strength - This is the intensity of the wireless signal received by the Adapter.Transmit Power - This is the power output at which the Adapter is transmitting.Up Time - This indicates the length of the most recent connection to a wireless network.Total Up Time - This indicates the cumulative total of the Adapter’s connection time.Signal Strength - The Signal Strength bar indicates the signal strength. Link Quality - The Link Quality bar indicates the quality of the wireless network connection.Click the Back button to return to the initial Link Information screen. Click the Status button to go to the Wireless Network Status screen. Click the Save to Profile button to save the currently active connection settings to a profile. Click the Refresh button to reset the statistics.Figure 5-4: More Information - Wireless Network Statistics18 dBm
23Chapter 5: Using the Wireless Network MonitorSite SurveyWireless-G USB Network Adapter with Wi-Fi FinderFigure 5-5: Site SurveyFigure 5-6: WEP Key Needed for ConnectionFigure 5-7: WPA-Personal Needed for ConnectionSite SurveyThe Site Survey screen displays a list of available networks in the table on the left. The table shows each network’s SSID, Channel, and the quality of the wireless signal the Adapter is receiving. You may click SSID, CH (Channel), or Signal, to sort by that field.SSID - The SSID or unique name of the wireless network is displayed here.CH - This is the channel that the network uses.Signal - This is the percentage of signal strength, from 0 to 100%.Site InformationFor each network selected, the following settings are listed:SSID - This the SSID or unique name of the wireless network. Wireless Mode - This is the mode of the wireless network currently in use.Channel - This is the channel to which the wireless network devices are set. Security - The status of the wireless security feature is displayed here.MAC Address- The MAC address of the wireless network’s access point is displayed here.Refresh - Click the Refresh button to perform a new search for wireless devices.Connect - To connect to one of the networks on the list, select the wireless network, and click the Connect button. If the network has encryption enabled, a screen appear requiring security information.If the network has the wireless security WEP encryption enabled, then you will see the WEP Key Needed for Connection screen. Select the appropriate level of WEP encryption, 64-bit or 128-bit Then enter the network’s Passphrase or WEP Key. To connect to the network, click Connect. To cancel the connection, click Cancel.If the network has WPA-Personal wireless security enabled, then you will see the WPA-Personal Needed for Connection screen. Select the appropriate encryption type, TKIP or AES. Enter the network’s Passphrase or pre-shared key in the Passphrase field. To connect to the network, click Connect. To cancel the connection, click Cancel.
24Chapter 5: Using the Wireless Network MonitorProfilesWireless-G USB Network Adapter with Wi-Fi FinderProfilesThe Profiles screen lets you save different configuration profiles for different network setups. The table on the left displays a list of available profiles with their profile names and SSIDs.Profile - The name of the profile is displayed here.SSID - The SSID or unique name of the wireless network is displayed here.Profile InformationFor each profile selected, the following are listed:Wireless Mode - This is the mode of the wireless network currently in use.Channel - This is the channel to which the wireless network devices are set. Security - The status of the wireless security feature is displayed here.Authentication - The authentication setting for the network is shown here.Connect - To connect to a wireless network using a specific profile, select the profile, and click the Connect button.New - Click New to create a new profile. See the next section, “Creating a New Profile,” for detailed instructions.Edit - Select the profile you want to change, and then click Edit. Import - Click Import to import a profile that has been saved in another location. Select the appropriate file, and click the Open button.Export - Select the profile you want to save in a different location, and click Export. Direct Windows to the appropriate folder, and click the Save button.Delete  - Select the profile you want to delete, and then click Delete. Figure 5-8: ProfilesFigure 5-9: Import a ProfileNOTE: If you want to export more than one profile, you must export them one at a time.Figure 5-10: Export a Profile
25Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with Wi-Fi FinderCreating a New ProfileOn the Profiles screen, click the New button to create a new profile. Enter a name for the new profile, and click the OK button. Click the Cancel button to return to the Profiles screen without entering a name.The Available Wireless Network screen will appear. This screen provides two options for setting up the Adapter•Available Networks. Use this option if you already have a network set up. The networks available to this Adapter will be listed on this screen. Select the network and click the Connect button to connect to it. Click the Refresh button to update the Available Wireless Network list.•Manual Setup. If your network is not listed on this screen, select Manual Setup to set up the adapter manually. This method of setting up the Adapter is intended for Advanced Users only.The setup for each option is described, step by step, under the appropriate heading on the following pages.Click Exit to close the Setup Wizard.Figure 5-11: Create a New ProfileFigure 5-12: Available Wireless Network
26Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with Wi-Fi FinderSetting Up the Adapter with Available NetworksThe available networks are listed in the table on the center of the screen by SSID. Select the wireless network you wish to connect to and click the Connect button. (If you do not see your network listed, you can click the Refresh button to bring the list up again.) If the network utilizes wireless security, you will need to configure security on the Adapter. If not, you will be taken directly to the Congratulations screen. 1. If wireless security has been enabled on this network, you will see a wireless security screen. If your network utilizes WEP (Wired Equivalent Privacy) encryption, the WEP Key Needed for Connection screen will appear. If your network utilizes WPA-Personal (Wi-Fi Protected Access) encryption, the WPA-Personal Needed for Connection screen will appear.WEP Key Needed for ConnectionSelect 64-bit or 128-bit. Then, enter a passphrase or WEP key.Passphrase - Enter a passphrase in the Passphrase field, so a WEP key is automatically generated. The passphrase is case-sensitive and should not be longer than 16 alphanumeric characters. It must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)WEP Key - The WEP key you enter must match the WEP key of your wireless network. For 64-bit encryption, enter exactly 10 hexadecimal characters. For 128-bit encryption, enter exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel.Figure 5-13: Available Wireless NetworkFigure 5-14: WEP Key Needed for Connection
27Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with Wi-Fi FinderWPA-Personal Needed for ConnectionEncryption - Select the type of algorithm you want to use, TKIP or AES, from the Encryption drop-down menu.Passphrase - Enter a Passphrase, also called a pre-shared key, of 8-63 characters in the Passphrase field. The passphrase must match the devices on your wireless network.Then, click Connect and proceed to the Congratulations screen. To cancel the connection, click Cancel. 2. After the software has been successfully installed, the Congratulations screen will appear. Click Connect to Network to connect to your network.Congratulations! The profile has been configured.Figure 5-15: WPA-Personal Needed for ConnectionFigure 5-16: The Congratulations Screen
28Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with Wi-Fi FinderSetting Up the Adapter with Manual SetupIf your network is not listed among the available networks, click Manual Setup on the Available Wireless Network screen to set up the adapter manually. 1. After clicking Manual Setup, the Network Settings screen will appear. If your network has a router or other DHCP server, click the radio button next to Obtain network settings automatically (DHCP).If your network does not have a Router or DHCP server, click the radio button next to Specify network settings. Enter an IP Address, Subnet Mask, Default Gateway, and DNS addresses appropriate for your network. You must specify the IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway and DNS addresses, leave these fields empty. IP Address - This IP Address must be unique to your network.Subnet Mask - The Adapter’s Subnet Mask must be the same as your wired network’s Subnet Mask.Default Gateway - Enter the IP address of your network’s Gateway here. DNS 1 and DNS 2 - Enter the DNS address of your wired Ethernet network here.Click Next to continue, or click Back to return to the Available Wireless Network screen.Figure 5-17: Available Wireless NetworkFigure 5-18: Network Settings
29Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with Wi-Fi Finder 2. The Wireless Mode screen shows a choice of two wireless modes. Click the Infrastructure Mode radio button if you want to connect to a wireless router or access point. Click the Ad-Hoc Mode radio button if you want to connect to another wireless device directly without using a wireless router or access point. Then, enter the SSID for your network.Infrastructure Mode - Use this mode if you want to connect to a wireless router or access point.Ad-Hoc Mode - Use this mode if you want to connect to another wireless device directly without using a wireless router or access point.SSID - This is the wireless network name that must be used for all the devices in your wireless network. It is case- sensitive and should be a unique name to help prevent others from entering your network.Click Next to continue or Back to return to the previous screen. 3. If you chose Infrastructure Mode, go to Step 4 now. If you chose Ad-Hoc Mode, the Ad-Hoc Mode Settings screen will appear.Select the correct Channel for your wireless network. The channel you choose should match the channel set on the other devices in your wireless network. If you are unsure about which channel to use, keep the default setting.Then, select the Network Mode in which your wireless network will operate. In Mixed Mode, Wireless-B and Wireless-G devices can both operate on the network, though at a slower speed. In G-Only Mode, no Wireless-B devices can operate in the network.Click Next to continue or click Back to change any settings.Figure 5-19: Wireless ModeFigure 5-20: Ad-Hoc Mode Settings
30Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with Wi-Fi Finder 4. The Wireless Security screen will appear. This step will configure wireless security.If your wireless network doesn’t use wireless security, select Disabled and then click the Next button to continue. Proceed to Step 6.Select WEP, WPA-Personal, WPA-Enterprise, or Radius for the Encryption Method. WEP stands for Wired Equivalent Privacy, WPA stands for Wi-Fi Protected Access, which is a security standard stronger than WEP encryption, and RADIUS stands for Remote Authentication Dial-In User Service. If you don’t want to use encryption, select Disabled. WEPWEP - To use WEP encryption, select 64-bits or 128-bit characters from the drop-down menu, and enter a passphrase or key.WEP Key - The WEP key you enter must match the WEP key of your wireless network. If you are using 64-bit WEP encryption, then the key must consist of exactly 10 hexadecimal characters. If you are using 128-bit WEP encryption, then the key must consist of exactly 26 hexadecimal characters. Valid hexadecimal characters are “0” to “9” and “A” to “F”.Passphrase - Instead of manually entering a WEP key, you can enter a passphrase in the Passphrase field, so a WEP key is automatically generated. This case-sensitive passphrase must match the passphrase of your other wireless network devices and is compatible with Linksys wireless products only. (If you have any non-Linksys wireless products, enter the WEP key manually on those products.)TX Key - The default transmit key number is 1. If your network’s access point or wireless router uses transmit key number 2, 3, or 4, select the appropriate number from the TX Key drop-down box.Authentication -The default is set to Auto, where it auto-detects for Shared Key or Open system. Shared Key is when both the sender and the recipient share a WEP key for authentication. Open key is when the sender and the recipient do not share a WEP key for authentication. All points on your network must use the same authentication type.Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen. Figure 5-21: Wireless SecurityFigure 5-22: Wireless Security - WEP
31Chapter 5: Using the Wireless Network MonitorCreating a New ProfileWireless-G USB Network Adapter with Wi-Fi FinderWPA PersonalWPA Personal offers two encryption methods, TKIP and AES, with dynamic encryption keys. Select the type of algorithm, TKIP or AES, for the Encryption Type. Enter a Passphrase of 8-63 characters in the Passphrase field. The passphrase must match the devices on your wireless network.Click the Next button to continue to the Confirm New Settings screen or the Back button to return to the previous screen. Figure 5-23: Wireless Security - WPA Personal

Navigation menu