LINKSYS WVC54GV1 Wireless-G Video Camera User Manual Book

LINKSYS LLC Wireless-G Video Camera Book

Contents

Part 1

A Division of Cisco Systems, Inc.®Model No.Internet Video CameraWireless-GWVC54G V1.1User GuideWIRELESSGHz2.4802.11g
Wireless-G Internet Video CameraCopyright and TrademarksSpecifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2004 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. How to Use this GuideYour guide to the Wireless-G Internet Video Camera has been designed to make understanding networking with the Camera easier than ever. Look for the following items when reading this guide:In addition to these symbols, there are definitions for technical terms that are presented like this:Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this:Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.This exclamation point means there is a Caution or warning and is something that could damage your property or the Camera.word: definition.This checkmark means there is a Note of interest and is something you should pay special attention to while using the Camera.This question mark provides you with a reminder about something you might need to do while using the Camera.Figure 0-1: Sample Figure DescriptionWVC54G-UG-40420NC JL
Wireless-G Internet Video CameraTable of ContentsChapter 1: Introduction 1Welcome 1What’s in this Guide? 2Chapter 2: Planning Your Wireless Network 4Introduction 4Ad-Hoc and Infrastructure Modes 4Network Layout 4Chapter 3: Getting to Know the Wireless-G Internet Video Camera 6Camera LCD Screen and Built-in Microphone 6Camera LEDs 6Camera Head 6Camera Ports 7Chapter 4: Connecting the Wireless-G Internet Video Camera for Setup 8Overview 8Connection to a Wired Network for Setup 8Connection to a Wireless Ad-Hoc Network for Setup 8Moving the Camera to a Different Network 9Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera 10Setup Wizard 10Placement Options 16Audio Option 16Chapter 6: Installing and Using the Wireless-G Internet Video Camera Viewer& Recorder Utility 17Overview 17Installing the Viewer & Recorder Utility 17Using the Viewer & Recorder Utility 19Chapter 7: Setting up the Linksys SoloLink™ DDNS Service 30Overview 30Introduction 30Setup Wizard for the SoloLink DDNS Service 30SoloLink Registration of Additional Cameras 40
Wireless-G Internet Video CameraChapter 8: Using the Wireless-G Internet Video Camera’s Web-based Utility 42Overview 42How to Access the Web-based Utility 42View Video 42Setup 43Help 54Appendix A: Troubleshooting 56Common Problems and Solutions 56Frequently Asked Questions 59Appendix B: Wireless Security 62Security Precautions 62Security Threats Facing Wireless Networks 62Appendix C: Upgrading Firmware 64Appendix D: Windows Help 65Appendix E: Glossary 66Appendix F: Specifications 73Appendix G: Warranty Information 75Appendix H: Regulatory Information 76Appendix I: Contact Information 79
Wireless-G Internet Video CameraList of FiguresFigure 3-1: Camera LCD Screen and Built-in Microphone 6Figure 3-2: Camera LEDs 6Figure 3-3: Camera Head 6Figure 3-4: Camera Ports 7Figure 4-1: Connect the Ethernet Network Cable 8Figure 4-2: Connect the Power Adapter 8Figure 5-1: Setup Wizard - Welcome Screen 10Figure 5-2: Connection for Setup Screen 10Figure 5-3: Cameras Found Screen 11Figure 5-4: Login Screen 11Figure 5-5: Basic Settings Screen 11Figure 5-6: Network Settings Screen 12Figure 5-7: IP Settings Screen 12Figure 5-8: Mode Settings Screen 13Figure 5-9: Wireless Settings Screen 13Figure 5-10: Security Settings Screen 14Figure 5-11: Review New Settings Screen 14Figure 5-12: Confirmation Screen 15Figure 5-13: Congratulations Screen 15Figure 5-14: Stand Option 16Figure 5-15: Camera Desktop Stand 16Figure 5-16: Wall Mount Option 16Figure 5-17: Wall-Mount Slots 16Figure 6-1: Install Viewer & Recorder Utility Screen 17Figure 6-2: Install Viewer & Recorder Utility - Welcome Screen 17Figure 6-3: Choose Destination Location Screen 18Figure 6-4: Select Program Folder Screen 18Figure 6-5: OCX Plug-in Screen 18
Wireless-G Internet Video CameraFigure 6-6: Setup Complete Screen 18Figure 6-7: Viewer & Recorder Utility Icon 19Figure 6-8: Main Screen 19Figure 6-9: Find Camera from LAN Screen 20Figure 6-10: Camera Added Successfully Screen 20Figure 6-11: Find Camera from Internet Screen 21Figure 6-12: Change Settings Screen 21Figure 6-13: Delete Camera Screen 22Figure 6-14: Confirm Deletion of Camera Screen 22Figure 6-15: View Video Screen 23Figure 6-16: Recording Icon Screen 23Figure 6-17: Scheduled Recordings in Progress Screen 26Figure 6-18: Files Screen 26Figure 6-19: Recorded Files Screen 26Figure 6-20: Window Showing SnapShot Folders 27Figure 6-21: Preferences Screen 27Figure 6-22: Recording Schedule Screen 28Figure 6-23: Add to Recording Schedule Screen 28Figure 6-24: Stop Scheduled Recording Screen 29Figure 6-25: View Video Screen 29Figure 7-1: SoloLink Service 30Figure 7-2: SoloLink Welcome Screen 30Figure 7-3: SoloLink for Dynamic IP Address Screen 31Figure 7-4: SoloLink for Convenience Screen 31Figure 7-5: Check Connections Screen 32Figure 7-6: Cameras Found Screen 32Figure 7-7: Login Screen 33Figure 7-8: SoloLink DDNS Screen 33Figure 7-9: Confirm Active Internet Connection Screen 34Figure 7-10: Welcome to the SoloLink DDNS Service Screen 34
Wireless-G Internet Video CameraFigure 7-11: Sign Up Screen 35Figure 7-12: Confirmation of New Settings Screen 36Figure 7-13: Select a Location ID Screen 36Figure 7-14: Confirm Your Location ID Screen 37Figure 7-15: Payment Screen 37Figure 7-16: Verification Screen 37Figure 7-17: Create Links Screen 38Figure 7-18: Successful Registration Screen 38Figure 7-19: Account Confirmation of Camera Screen 39Figure 7-20: Successful Setup Screen 39Figure 7-21: Port Forwarding Information 40Figure 7-22: Web-based Utility Welcome 40Figure 7-23: Web Utility Login Screen 40Figure 7-24: SoloLink DDNS Screen 41Figure 7-25: Find Available Port Screen 41Figure 8-1: Camera’s Default IP Address 42Figure 8-2: Web-based Utility Welcome 42Figure 8-3: Security Warning Screen 43Figure 8-4: Web Utility Login Screen 43Figure 8-5: Basic Screen 44Figure 8-6: Confirmation Screen 45Figure 8-7: WEP Key Settings Screen 45Figure 8-8: Image Screen 46Figure 8-9: Password Screen 47Figure 8-10: Users Screen 48Figure 8-11: Add/Modify User Screen 48Figure 8-12: SoloLink DDNS Screen 49Figure 8-13: New User Registration Screen 49Figure 8-14: Password Request Screen 50Figure 8-15: Manage Your SoloLink DDNS Account 50
Wireless-G Internet Video CameraFigure 8-16: Device Removal Screen 50Figure 8-17: Find Available Port Screen 51Figure 8-18: Status Screen 52Figure 8-19: Options Screen 53Figure 8-20: Administrator Help 54Figure 8-21: Upgrade Firmware Screen 55Figure C-1: Upgrade Firmware Screen 64
1Chapter 1: IntroductionWelcomeWireless-G Internet Video CameraChapter 1: IntroductionWelcomeThank you for choosing the Linksys Wireless-G Internet Video Camera. This Camera sends live video through the Internet to a web browser anywhere in the world! This compact, self-contained unit lets you keep an eye on your home, your kids, your workplace—whatever’s important to you.How does the Camera do all of this? Unlike standard “web cams” that require an attached PC, the Internet Video Camera contains its own web server, so it can connect directly to a network, either over Wireless-G (802.11b) networking, or over 10/100 Ethernet cable. The advanced MPEG-4 video compression produces a high-quality, high-framerate, up to 640 x 480 audio/video stream.The Internet Video Camera’s unique form-factor and wireless connectivity allows you to mount it on a wall nearly anywhere, or slip it into its included stand for desktop use. Once it’s connected to your home network, you can “see what it sees” from any PC in the house, while the audio/video stream is secured from the outside world, hidden behind your Router. If you want the video to be visible from outside your home network, you can open an appropriate port on the Router, and then create password-protected accounts to manage access to the Camera, or leave it wide open for the world to see. The SoloLink DDNS Service (trial sign-up included) lets you access your Camera using an easy-to-remember “name”, even if your home Internet connection uses a dynamic IP address.You can also turn on Security Mode, which tells the Camera to send you an e-mail message with a short video attached to up to three e-mail addresses whenever it detects motion in its field of view. You can then log onto the live video stream if the situation warrants. The included Viewer & Recorder utility lets you record the audio/video stream to your local hard drive, “live” or on a predetermined schedule.Use the instructions in this Guide to help you integrate the Camera into your network. These instructions should be all you need to get the most out of the Wireless-G Internet Video Camera.Ethernet: an IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium.802.11g: An IEEE wireless networking standard that specifies a maximum data transfer rate of 54Mbps, an operating frequency of 2.4GHz, and backward compatibility with 802.11b devices.
2Chapter 1: IntroductionWhat’s in this Guide?Wireless-G Internet Video CameraWhat’s in this Guide?This user guide covers the steps for setting up and using the Wireless-G Internet Video Camera.• Chapter 1: IntroductionThis chapter describes the Camera’s applications and this User Guide.• Chapter 2: Planning Your Wireless NetworkThis chapter discusses a few of the basics about wireless networking.• Chapter 3: Getting to Know the Wireless-G Internet Video CameraThis chapter describes the physical features of the Camera.• Chapter 4: Connecting the Wireless-G Internet Video CameraThis chapter instructs you on how to connect the Camera to your network before you run the Setup Wizard.• Chapter 5: Setting up and Mounting the Wireless-G Internet Video CameraThis chapter instructs you on how to use the Setup Wizard for setup and configuration of the Camera, as well as how to mount the Camera.• Chapter 6: Installing and Using the Wireless-G Internet Video Camera UtilityThis chapter explains how to install and use the Wireless-G Internet Video Camera Utility on your PC, so you can view and record video.• Chapter 7: Setting up the Linksys SoloLink™ DDNS ServiceThis chapter discusses the advantages of the SoloLink DDNS Service and walks you through the setup procedure.• Chapter 8: Using the Wireless-G Internet Video Camera Web-based UtilityThis chapter describes the Web-based Utility and the features available, so you can use and alter advanced configuration settings.• Appendix A: TroubleshootingThis appendix describes some problems and solutions, as well as frequently asked questions, regarding installation and use of the Camera.• Appendix B: Wireless SecurityThis appendix discusses security issues regarding wireless networking and measures you can take to help protect your wireless network.
3Chapter 1: IntroductionWhat’s in this Guide?Wireless-G Internet Video Camera• Appendix C: Upgrading FirmwareThis appendix explains how you can upgrade the Camera’s firmware.• Appendix D: Windows HelpThis appendix describes how you can use Windows Help for instructions about networking, such as installing the TCP/IP protocol.• Appendix E: GlossaryThis appendix gives a brief glossary of terms frequently used in networking.• Appendix F: SpecificationsThis appendix provides the technical specifications for the Camera.• Appendix G: Warranty InformationThis appendix supplies the warranty information for the Camera.• Appendix H: Regulatory InformationThis appendix supplies the regulatory information regarding the Camera.• Appendix I: Contact InformationThis appendix provides contact information for a variety of Linksys resources, including Technical Support.
4Chapter 2: Planning Your Wireless NetworkIntroductionWireless-G Internet Video CameraChapter 2: Planning Your Wireless NetworkIntroductionA wireless local area network (WLAN) is exactly like a regular local area network (LAN), except that each computer in the WLAN uses a wireless device to connect to the network. Computers and other devices, such as peripherals, in a WLAN share the same frequency channel and SSID, which is an identification name for wireless devices.Ad-Hoc and Infrastructure ModesUnlike wired networks, wireless networks have two different modes in which they may be set up: infrastructure and ad-hoc. An infrastructure configuration is a WLAN and wired LAN communicating to each other through an access point. An ad-hoc configuration is wireless-equipped computers communicating directly with each other. Choosing between these two modes depends on whether or not the wireless network needs to share data or peripherals with a wired network or not.If the computers on the wireless network need to be accessed by a wired network or need to share a peripheral, such as a printer, with the wired network computers, the wireless network should be set up in infrastructure mode. The basis of infrastructure mode centers around an access point, which serves as the main point of communications in a wireless network. (A wireless router can also be used because a wireless router incorporates the capabilities of an access point.) Access points transmit data to PCs equipped with wireless network cards, which can roam within a certain radial range of the access point. Multiple access points can be arranged to work in succession to extend the roaming range, and can be set up to communicate with your Ethernet (wired) hardware as well.If the wireless network is relatively small and needs to share resources only with the other computers on the wireless network, then the ad-hoc mode can be used. Ad-hoc mode allows computers equipped with wireless transmitters and receivers to communicate directly with each other, eliminating the need for an access point. The drawback of this mode is that, in Ad-Hoc mode, wireless-equipped computers are not able to communicate with computers on a wired network. And, of course, communication between the wireless-equipped computers is limited by the distance and interference directly between them.Network LayoutThe Wireless-G Internet Video Camera is compatible with all 802.11b and 802.11g routers, such as model numbers BEFW11S4 and WRT54G, as well as access points, including model numbers WAP11 and WAP54G. The Infrastructure: configuration in which a wireless network is bridged to a wired network via an access point.LAN (Local Area Network): the computers and networking products that make up the network in your home or office.Ad-hoc: a group of wireless devices communicating directly to each other (peer-to-peer) without the use of an access point.WLAN (Wireless Local Area Network): A group of computers and associated devices that communicate with each other wirelessly.
5Chapter 2: Planning Your Wireless NetworkNetwork LayoutWireless-G Internet Video CameraCamera will also communicate with network adapters, such as the Wireless-B and Wireless-G Notebook Adapters (model numbers WPC11 and WPC54G) for your laptop computers, Wireless-B and Wireless-G PCI Adapters (model numbers WMP11 and WMP54G) for your desktop PCs, and Wireless-B and Wireless-G USB Adapters (model numbers WUSB11 and WUSB54G) for your computers when you want to enjoy USB connectivity.With these, and many other Linksys products, your networking options are limitless. Go to the Linksys website at www.linksys.com for more information about products that work with the Wireless-G Internet Video Camera.
6Chapter 3: Getting to Know the Wireless-G Internet Video CameraCamera LCD Screen and Built-in MicrophoneWireless-G Internet Video CameraChapter 3: Getting to Know the Wireless-G Internet Video CameraCamera LCD Screen and Built-in MicrophoneThe Camera has a LCD screen that indicates the Camera’s current IP address and whether it is a fixed or dynamic address. If the Camera uses a fixed IP address, then the screen will display the word “FIXED.” If the Camera uses a dynamic IP address, then the screen will display the word “DHCP.” The built-in microphone is located approximately one inch below the LCD screen, in the middle of the Camera’s front panel. It has a range of approximately 9 feet (3 meters), depending on environmental conditions.Camera LEDsThe Camera has four LEDs to let you know how the Camera is functioning.READY Green. The READY LED lights up when the Camera is powered on. It flashes while the Camera is initializing and is steadily lit when the Camera is ready for use.ACT/LINK Green. The ACT/LINK LED flashes when there is activity.ETHERNET Green. The ETHERNET LED lights up when there is a connection to a wired network. It flashes when data is transmitted to or received from the wired network.WIRELESS Green. The WIRELESS LED lights up when there is a connection to a wireless network. It flashes when data is transmitted to or received from the wireless network.Camera HeadThe Camera head and its focus ring allow you to modify the aim and focus of the Camera.To alter the Camera’s aim, swivel the Camera head.To adjust the Camera’s focus, rotate the dark gray focus ring.Figure 3-1: Camera LCD Screen and Built-in MicrophoneFigure 3-2: Camera LEDsFigure 3-3: Camera HeadBuilt-in Microphone
7Chapter 3: Getting to Know the Wireless-G Internet Video CameraCamera PortsWireless-G Internet Video CameraCamera PortsThe Camera features three ports and a Reset button on the bottom panel.POWER The POWER port is where you will connect the power adapter.MIC IN The MIC IN port is where you will connect the 2.5 mm input jack of your external microphone (optional).ETHERNET The ETHERNET port is where you will connect the Ethernet network cable.RESET The RESET button is what you will press if you need to reset the Camera. Insert a paper clip into the opening next to the Ethernet port. Then press the button and hold it in for five seconds. IMPORTANT: Resetting the Camera will erase all of your settings, such as encryption information, and replace them with the factory defaults. Do not reset the Camera if you want to retain these settings.Figure 3-4: Camera Ports
8Chapter 4: Connecting the Wireless-G Internet Video Camera for SetupOverviewWireless-G Internet Video CameraChapter 4: Connecting the Wireless-G Internet Video Camera for SetupOverviewBefore you set up the Camera, connect it to a wired or wireless network. Proceed to the appropriate section for your setup.If you need to move the Camera from a wired network to a wireless network, or vice versa, go to this section, “Moving the Camera to a Different Network.”Connection to a Wired Network for Setup1. Attach the antenna.2. Connect the Ethernet network cable to your router, switch, or computer.3. Connect the other end of the cable to the Ethernet port on the Camera. See Figure 4-1.4. Connect the power adapter to the Power port on the Camera.5. Plug the power adapter into an electrical outlet.The Camera’s Ready LED flashes while the Camera is initializing. The Camera is ready for use when the Ready and Ethernet LEDs are solidly lit.Proceed to “Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera.”Connection to a Wireless Ad-Hoc Network for Setup1. Make sure your computer has the following wireless settings:• SSID - linksys• Network Mode - Ad-Hoc• Channel - 6• WEP - Disabled2. Attach the antenna.NOTE: You MUST connect the Camera to a PC, router, or switch using the Ethernet network cable BEFORE powering on the Camera. Otherwise, the Camera will not function.Figure 4-2: Connect the Power AdapterFigure 4-1: Connect the Ethernet Network Cable
9Chapter 4: Connecting the Wireless-G Internet Video Camera for SetupMoving the Camera to a Different NetworkWireless-G Internet Video Camera3. Connect the power adapter to the Power port on the Camera.4. Plug the power adapter into an electrical outlet.The Camera’s Ready LED flashes while the Camera is initializing. The Camera is ready for use when the Ready and Wireless LEDs are solidly lit.Proceed to “Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera.”Moving the Camera to a Different NetworkWhen you move the Camera from a wired network to a wireless network, or vice versa, you must power off the Camera before connecting to the new network. Proceed to the appropriate instructions.To move the Camera from a wired network to a wireless network, follow these instructions:1. Unplug the power adapter from the Camera.2. Unplug the Ethernet network cable from the Camera.3. Re-connect the power adapter to the Power port on the Camera.The Camera’s Ready LED flashes while the Camera is initializing. The Camera is ready for use when the Ready and Wireless LEDs are solidly lit.Proceed to “Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera.”To move the Camera from a wireless network to a wired network, follow these instructions:1. Unplug the power adapter from the Camera.2. Connect the Ethernet network cable to your PC, router, or switch.3. Connect the other end of the cable to the Ethernet port on the Camera.4. Re-connect the power adapter to the Power port on the Camera.The Camera’s Ready LED flashes while the Camera is initializing. The Camera is ready for use when the Ready and LAN LEDs are solidly lit.Proceed to “Chapter 5: Setting up and Mounting the Wireless-G Internet Video Camera.”
10Chapter 5: Setting up and Mounting the Wireless-G Internet Video CameraSetup WizardWireless-G Internet Video CameraChapter 5: Setting up and Mounting the Wireless-G Internet Video CameraSetup WizardThe Wireless-G Internet Video Camera Setup Wizard will guide you through the installation and configuration procedure.1. Insert the Setup CD-ROM into your CD-ROM drive. The Setup Wizard should run automatically, and the Welcome screen should appear. If it does not, click the Start button and choose Run. In the field provided, enter D:\wvc54g.exe (if “D” is the letter of your CD-ROM drive).•Setup. Click the Setup button to begin the installation process.•Install Viewer & Recorder Utility. Click this button to install the Camera’s Viewer & Recorder Utility on your PC.•Setup SoloLink DDNS Service. Click the Setup SoloLink DDNS Service button to configure and use Linksys’s Dynamic Domain Name System (DDNS) service.•User Guide. Click this button to open the PDF file of this User Guide.•Exit. Click the Exit button to exit the Setup Wizard.2. To install the Camera, click the Setup button on the Welcome screen.3. When you see the screen shown in Figure 5-2, make sure the Camera is properly connected to either a wired or wireless network. Then click the Next button to continue.Figure 5-2: Connection for Setup ScreenFigure 5-1: Setup Wizard - Welcome Screen
11Chapter 5: Setting up and Mounting the Wireless-G Internet Video CameraSetup WizardWireless-G Internet Video Camera4. The screen shown in Figure 5-3 displays a list of Wireless-G Internet Video Cameras on your network, along with the status information for the Camera whose name is highlighted. In the Selection box, click the name of the Camera you are currently installing. Write down the IP address of the Camera, so you can use it to access the Web-based Utility later. Click the Next button.5. For security purposes, you will be asked to enter a name and password in order to have administrator access to the Camera. In lowercase letters, enter admin in the Administrator Name and Administrator Password fields (later you can change these through the Web-based Utility). Then click the OK button.6. On the Basic Settings screen, you can alter the following settings:•Camera Name. You can give the Camera a unique name. Memorable names are helpful, especially if you are using multiple Cameras on the same network. It should have 15 characters or fewer.•Description. You may enter additional information, such as location, in this field. It has a maximum length of 32 characters.•Time Zone. Select the time zone for the Camera’s location.•Date. Enter today’s date in the fields provided.•Time. Enter the current time in the fields provided.When you have finished making your changes, click the Next button.Figure 5-4: Login ScreenFigure 5-3: Cameras Found ScreenFigure 5-5: Basic Settings Screen
12Chapter 5: Setting up and Mounting the Wireless-G Internet Video CameraSetup WizardWireless-G Internet Video Camera7. If your network has a DHCP server, such as a router with DHCP enabled, click the Automatic Configuration-DHCP radio button. If you need to assign a static IP address to the Camera, keep the default setting, Static IP address.Then click the Next button.8. If you selected Automatic Configuration-DHCP in step 7, then proceed to step 9. If you selected Static IP Address, then the IP Settings screen will appear. Enter an IP Address, Subnet Mask, and Default Gateway appropriate for your network. You must specify an IP Address and Subnet Mask on this screen. If you are unsure about the Default Gateway, it is better to leave this field blank. Then complete the Primary DNS and/or Secondary DNS fields. You must enter at least one DNS address, which can be obtained from your ISP. Click the Next button.Figure 5-6: Network Settings ScreenFigure 5-7: IP Settings Screen

Navigation menu