LITE ON TECHNOLOGY CR1004 User Manual 34488

Download:
Mirror Download [FCC.gov]
Document ID	34488
Application ID	HvTbuPHYRv6KFPaJ8MpOdQ==
Document Description	8
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.59kB (132383 bits)
Date Submitted	1999-04-27 00:00:00
Date Available	1999-04-29 00:00:00
Creation Date	2001-06-29 17:44:36
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-06-29 17:44:41
Document Title	34488.pdf
Document Author:	VicodinES /CB /TNN

NEUTRON EMC LAB.
FCC ID: H4ICDR1®®4
Attachment
User’s Manual
ATAPIlE-IDE
CD-ROM DRIVE
User's Manual
Gebrauchsanleitung
Manual del Ussuario
Manuel pour l’utilisation
Manuale dell’utente
Gebruiksaanwijzing
FCC Compliance statement
This equipment has been tested and found to comply with the limits for a Class 13 digital device.
pursuant to Pan IS of the FCC Rules These lirttits are designed to provide reasonable protection
against harmful interfuewce in a residential installation. This equipmmt generates, uses and can
radiate radio frequency enery and, ifnot installed or used in accordance with the instructions. may
cause harmful interference to radio communications, However. there is no guarantee that
interference will not occur in a television reception, which can be determined by turning the
equipment MT and on, the user is encouraged to try and correct the interference by one or more of
the following measures (1) Reorient or relocate the receiving antenna. (2) Increase the separation
between the equipment and the receiver (3) Connect the equipment into an outlet on a circuit
difl‘erent from that to which the receiver is connected (4) Consult the duler or an experienced
radiofr V technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate the equipment
Acknowledgment a. Trademark
All contents are subject to change at any time without notice No responsibility is assumed for its
use, not for infringements of patents or other rights of third parties and no patent or license is
implied hereby
All trademarks are the property ot‘their respective owners
(6
Safety Notice
1 Do not install or operate the product in high temperature. humidity or dusty environment
2 Do not attempt to open the cover to repair the product yourself
3 Never spill liquid ofany kind on the product
4c Always follow instmctions on this manual under operating the product.
. To prevent exposure to laser emanations(harmful to human eyes), do not attempt to disassemble
this unit
6 Hold CD discs by their edges Do not touch the surface of the discs.
7 The drive is designed to be incorporated into a computer-based system or unit which has an
enclosing cover Using the drive alone or in any other configuration is prohibited.
Caution: Use of controls or adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure
M-LTN-SLB-970E
NGLIS
HARDWARE INSTALLATION
Turn off your PC and disconnect all power cords‘
Refer to your PC user's manual to remove the PC cover,
Set up your CD~ROM to Master or Slave device according to the following section
Find an empty bay, slide the CD~ROM into the bay and mount the drive by using 4
screws
5 Connect the power cable to your CD-ROM drive,
No TE; The pin definition o/powzr connector should be the some in that in figure I.
6 Connect the E~IDE cable (40 pin) to your CD-ROM according to the description in the
following section
7 Connect the sound cable from the Analog Audio on the rear panel of your CDvROM to
your sound card if you have a sound card in your system
NOTE: The R channel i4- normalh- in red color,
8 Put the PC cover back and connect the power cords
pinto...
Set Master or Slave Jumper
There are three pairs ofjurnpers, MA(Master), SuSlave) and CS(CSEL) on the rear panel
ofyour CD-ROM drive. Figure 1 shows the location ofthe jumper.
c 5 CT
mam; ANALOG sfi’fi “E
AUDIO ALDIO Mm Hosrirrznuct
c s w 3; “x
s l, A m \2
Figure 1: Rear pane] ofCD-ROM drive
The Master Slave jumper can be used to set the CD-ROM drive to Mar/er or Slave device.
Figure 2 IS the illustration of jumper semng.
c s M c s M
s L A s L A
ManaDcwce ShveDevine
(Def-winttma)
Figure 2: The setting ofMasier or Slave dewce.
NOTE: Do not use rwojumpers (a set MA and SL sbnuhanenusiy. -
'*‘~_—fl
ENGLISH
Connect to Primary/Secondary IDE Port
—_.__——____
In most ofthe PC systems. the hard disk will be in Primary IDE pen and Master device for
the PC to boot the operating system. CD-ROM drive should be set to Slaw: device if you
need to connect your CD-ROM to the same Primary IDE part In some situations, you may
need to conneor your CD-ROM drive to Secondary IDE port if the Primary [DE port is
occupied. In this configuration the CD-ROM drive can be set to Master device if there is
no any other device in this Secondary IDE porn Otherwise, the CD-ROM drive should be
set to Slave device if Master dewcz already exists. Figure 3 shows the semng and the
connection ofyour CD»ROM to Primary IDE port or in Secondary IDE pone Table 1
illustrates the configuration of your CD-ROM if you want lo use Secondary IDE ports
pc Mulher Board
Secondary 1135 Pan
Primary 1135 Port
Figure 3 ' The connection oanmmjv or Secondary IDE Parr.
MDevioe 0 (Master) Device l (Slave)
_Hard disk chD-ROM CD»ROM
Table 1 The con/ignranun of Secondary IDE Purl.
SOFTWARE INSTALLATION
There is a dewce drlI/Er diskette in your CD-ROM drive package The device driver is
needed if your PC system is in DOS or Windows 3.1 or higher. Please follow the
procedures listed below if you need to install the device drrver in your system. Usually the
device driver is not necessary if you run the Windows 95, Windows NT, or 05/2. Please
refer the following procedures or the user's guide of the operating system if the CD-ROM
can't be recognized automatically.
DOS or Windows 3.x
Power on your PC and insen the driver diskette into a floppy drive.
Type A:(a:) or B:(li:) where the driver diskette locates.
Type Install under DOS prompt and Press Enter key.
Follow the instruction on the screen.
After the installation. remove the driver dirkct/c and reboot your system.
Windows 95
There is no need to install any CD-ROM device driver under Windows 95 system. Please
follow steps below if your CD-ROM can‘t be recognized automatically.
1 Stan-up your PC, the system will detect the new CD»ROM drive and use the soi‘nvare
device driver automatically If not. please proceed the next steps.
Click on g antral Panel icon under Myg omnuter
Click on Add New Hardware icon and Click M and m at the dialog boxes.
Follow the instructions on the screen and let Windows 95 search your new hardware. lt
will find the CD-ROM drive and load the driver software to complete the installation.
Windows NT or 0512 WARP
It is also not necessary (0 insrall the device driver under these operating systems. Please
refer the user's guide offliese operating systems if the CD-ROM can‘t be recognized
automatically .
mAle~
pwp
NOTE: Please read the README file an the driver diskette fur any updater made
afier this manuaL
EN ISH
USING THE CD-ROM DRIVE
{D Earphune Jack The user can use a stereo headphone to get sound output from
the earphone jack.
Q Volume Knob The user can adjust this knob to change the volume of
earphone.
9 OnlBusy LED The On/Busy LED will be flashinpv while the CDaRDM disc is
busy
3 Door The user can open or close the Door by pressing Ll):
Opem Close bunun.
3 Emergency Eject It“ the user can not eject the disc by pressing the Open/Close
butiun. he’slie can insert a small rod into this hole far manual
ejection.
NO TE: Please turn of] the power befare this manual ejection.
“iv Play/Skip When a CD-DA (Music) disc is loaded and the drive is not
playing, pressing this huncn Will make the drive start playing
from the lst truckisong), When the drive is playing, pressing
this button will cause the drive to skip to the next mick(50m_i)
Open/Close/Stop This is a toggle button. When pressed, the CD»ROM drive Wlll
eiiher open the door and tray out the discs or tray in the disc
and close die door. when playing a CD-DA disc. pressing this
hutirm Will stop playing
ED

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2001:06:29 17:44:36
Producer                        : Acrobat Distiller 4.0 for Windows
Author                          : VicodinES /CB /TNN
Title                           : 34488.pdf
Modify Date                     : 2001:06:29 17:44:41-04:00
Page Count                      : 7

EXIF Metadata provided by EXIF.tools