LITE ON TECHNOLOGY CR8702SB JukeBlox Networked Media User Manual manual

LITE-ON Technology Corp. JukeBlox Networked Media manual

UserManual.wiki >

LITE ON TECHNOLOGY >

CR8702SB User Manual

manual

SMSC CR860/CR870 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL JukeBlox Networked Media Module CR Series Datasheet • Complete audio networking system on a small module • Integrated Ethernet + USB2.0 • WiFi-certified 802.11b/g • Built-in PIFA antenna • Glueless audio, video and control ports • FCC certified • Ideal for enabling network and USB audio playback for iPod docks, audio systems, AV Receivers, active speaker systems, internet radios, network playback adaptors

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 2 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 80 ARKAY DRIVE, HAUPPAUGE, NY 11788 (631) 435-6000 or 1 (800) 443-SEMI Copyright © 2011 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 3 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL Table of Contents 1 INTRODUCTION............................................................................................................... 4 2 BLOCK DIAGRAM ............................................................................................................. 4 3 BOARD PICTURES............................................................................................................ 5 3.1 TOP VIEW OF CR870-2A ................................................................................................... 5 3.2 BOTTOM VIEW OF CR870 TYPES 2A, 2D & 2S .......................................................................... 5 3.3 TOP VIEW OF CR870 TYPES 2C, 2F, 2G, 2I, 2J, 2K & 2R ........................................................... 6 3.4 BOTTOM VIEW OF CR870 TYPES 2C, 2G, 2I, 2J, 2K, 2L, 2N, 2O, 2P & 2R...................................... 6 3.5 TOP VIEW OF CR870 TYPES 2D, 2L, 2N, 2O, 2P, 2Q & 2S(INCLUDING 2S-B) ............................... 7 3.6 TOP VIEW OF CR870-2J .................................................................................................... 8 3.7 BOTTOM VIEW OF CR870-2J ............................................................................................... 8 3.8 TOP VIEW OF CR870-2R ................................................................................................... 9 3.9 BOTTOM VIEW OF CR870-2R .............................................................................................. 9 4 ORDERING GUIDE ......................................................................................................... 10 5 ELECTRICAL SPECIFICATIONS....................................................................................... 11 5.1 ABSOLUTE MAXIMUM RATINGS............................................................................................ 11 5.2 OPERATING CONDITIONS................................................................................................... 12 5.3 WIFI SPECIFICATION (CR870 ONLY) .................................................................................... 12 6 REGULATORY COMPLIANCE AND QUALITY .................................................................... 13 6.1 ROHS ........................................................................................................................ 14 6.2 ENVIRONMENTAL TEST...................................................................................................... 14 6.3 ESD AND TRANSIENT TEST (APPLIES TO LAN AND USB EXTERNAL CONNECTIONS ONLY) ......................... 14 6.4 MAGNETIC FIELD TEST..................................................................................................... 14 6.5 MTBF ........................................................................................................................ 14 6.6 MECHANICAL SPECIFICATIONS............................................................................................. 14 6.7 MODULE QUALITY........................................................................................................... 14 7 BOARD DIMENSIONS AND WEIGHT ............................................................................... 15 7.1 TOP VIEW AND SIDE VIEW OF CR870 MODULES WITH PIFA ANTENNA & NO SHIELDS............................. 15 7.2 BOTTOM VIEW OF CR870 MODULES WITH NO BOTTOM SHIELD........................................................ 15 7.3 TOP VIEW AND SIDE VIEW OF CR870 MODULES WITHOUT PIFA ANTENNA.......................................... 16 7.4 TOP VIEW AND SIDE VIEW OF CR870 MODULES WITH PIFA ANTENNA & TOP SHIELD.............................. 16 7.5 MODULE WEIGHT............................................................................................................ 17 8 CONNECTORS AND CONNECTIONS ................................................................................ 17 8.1 WLAN UFL ANTENNA CONNECTOR (OPTIONAL) ........................................................................ 17 8.2 MODULE CONNECTORS..................................................................................................... 17 8.2.1 Pin Descriptions ................................................................................................... 18 8.2.2 Connector PIN Assignments................................................................................... 23 9 APPLICATION GUIDELINES ........................................................................................... 24 9.1 POWER SUPPLY SEQUENCING AND RESET TIMING....................................................................... 24 9.1.1 Power up, Reset and Power Down Timing ................................................................ 25 9.2 RF CONSIDERATIONS....................................................................................................... 25 10 REVISION CONTROL.................................................................................................... 26

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 4 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 1 Introduction The CR-series module is a single-board networked media player module, based on SMSC’s DM860 and DM870 media processors, and enables fast product developments with Ethernet, USB and optional WiFi connectivity. The module connects to standard legacy components in various audio, video/LCD and control formats. 2 Block Diagram Ethernet PHYDM860orDM870 256 MbitSDRAMJTAGRJ-45100B-TMemUSBGPIO24.000 MHzReset InNAND1 GBNAND flash802.11RF amp(optional)802.11RMIISPIUSB(Host)USBRSTUART5V3.3VJukeBlox Networked Media Module – CR Series1.2VStereo OutVideo OutAudio I/O4/8bit MMC3x6bit RGB2 x UARTSPI Ctrl.max. 20 GPIOsIR sensorreset signalsanalog muteI2C busshift registerIC controlserial controlA/D, D/AS/PDIFCCIR-656LP2HP outDisplaySD-CardAV PortsLCDSSMDACPIFAAntenna1.9V Power Supply3.3V

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 5 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 3 Board Pictures 3.1 Top View of CR870-2A 3.2 Bottom View of CR870 types 2A, 2D & 2S(including 2S-B) PIFA antenna 802.11b/g front-end SMSC processor Ethernet FLASH SDRAM antenna connector Note: Components and Socket to the right of the Ethernet and Flash sections are not installed in production modules. Please see Section 3.3 for example production module top view picture. Media connector LCD connector +1.9V DC to DC converter Note: The connector shown to the left of the LCD connector is not installed on production modules. Please see section 3.4 for example production module bottom view picture.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 6 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 3.3 Top View of CR870 types 2C, 2F, 2G, 2I, 2J, 2K & 2R 3.4 Bottom View of CR870 types 2C, 2G, 2I, 2J, 2K, 2L, 2N, 2O, 2P & 2R Version with no top shield. Please note that label text will change to show version, and versions 2I, 2J, 2K will have no Ethernet components mounted. Versions with no bottom shield and no LCD connector. Please note that production version does not have exposed solder on the underside of the mounting holes.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 7 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 3.5 Top View of CR870 types 2D, 2L, 2N, 2O, 2P, 2Q & 2S(including 2S-B) Versions with top shield. For versions without PIFA antenna, PIFA antenna is not present and UFL connector is present, see the top view of CR870-2A for location of UFL connector.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 8 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 3.6 Top View of CR870-2J 3.7 Bottom View of CR870-2J

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 9 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 3.8 Top View of CR870-2R 3.9 Bottom View of CR870-2R

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 10 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 4 Ordering Guide Part Number SMSC ICs WiFi Ethernet USB Real-Time Clock LCD PIFA Antenna Ext. Antenna UFL Conn. SDRAM Top Module Shielding Contains shield Incl. connector CR870-2A DM870+T6201 X X X X X X (X)* 32MB CR870-2C DM870+T6201 X X X X 32MB CR870-2D DM870+T6201 X X X X X 32MB X CR870-2F DM870+T6201 X X X X X X (X)* 32MB CR870-2G DM870+T6201 X X X X 32MB CR870-2I DM870+T6201 X X X 16MB CR870-2J DM870+T6201 X X X X 16MB CR870-2K DM870+T6201 X X X X 16MB CR870-2L DM870+T6201 X X X X 32MB X CR870-2M DM870+T6201 X X X X X X (X)* 32MB X CR870-2N DM870+T6201 X X X 16MB X CR870-2O DM870+T6201 X X X X 16MB X CR870-2P DM870+T6201 X X X X 32MB X CR870-2Q DM870+T6201 X X X X 32MB X CR870-2R DM870+T6201 X X X X 16MB CR870-2S DM870+T6201 X X X X X 32MB X CR870-2S-B DM870+T6201 X X X X X 32MB X CR860-2A DM860 n/a X X n/a n/a 32MB CR860-2B DM860 n/a X X X X n/a n/a 32MB * Connector on board, but not enabled Note: Shaded rows are Custom or Obsolete configurations – not to be used for new / standard MP designs.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 11 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 5 Electrical Specifications Parameter State Model Voltage Symbol min. typ. max. Units Power Supply Voltage VIN +2.97 +1.08 +3.3 +1.2 +3.63 +1.32 V V Logic Input high voltage VIH 1.7 5.5 V Logic Input low voltage VIL -0.3 0.7 V Logic Input threshold voltage VIT 1.29 1.39 1.5 V Schmitt-trigger input low to high threshold voltage VIT+ 1.58 1.65 1.71 V Schmitt-trigger input high to low threshold voltage VIT- 0.95 1.01 1.06 V Logic Output high voltage VOH 2.4 V Logic Output low voltage VOL 0.4 V Logic Low-level output current (VOL=0.4V) IOL -9.6 -15.6 -19.3 mA Logic High-level output current (VOH=2.4V) IOH 11.1 22.5 35.3 mA 3.3V PIN3.3 - 230 300 mW CR870 int 1.9V 1.2V PIN1.2 - 45 60 mW 3.3V PIN3.3 - 165 215 mW 1.2V PIN1.2 - 45 60 mW CR870 ext 1.9V 1.9V PIN1.9 - 35 50 mW 3.3V PIN3.3 - 145 190 mW Reset State CR860 1.2V PIN1.2 - 45 60 mW 3.3V PIN3.3 - 1750 2275 mW CR870 int 1.9V 1.2V PIN1.2 - 600 800 mW 3.3V PIN3.3 - 825 1075 mW 1.2V PIN1.2 - 600 800 mW WLAN Operating CR870 ext 1.9V 1.9V PIN1.9 - 535 700 mW 3.3V PIN3.3 - 760 990 mW Power Consumption Operating CR860 1.2V PIN1.2 - 600 800 mW Note: The maximum power consumption values are 30% larger than the typical values. The maximum values are intended to be used for power supply sizing calculations. 5.1 Absolute Maximum Ratings Parameter Component Min Max Units 3.3V Supply Voltage -0.5 4.6 V 1.2V Supply Voltage -0.5 1.8 V Logic Input Voltage -0.5 6 V Logic Output Voltage Main -0.5 4.6 V

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 12 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 5.2 Operating Conditions Parameter Min Max Units Operating Temperature 0 +70 °C Operating Humidity 10 90 (non condensing) %RH Storage Temperature -10 +75 °C Storage Humidity 10 95 (non condensing) %RH Storage Temperature Cycle Test 24 hrs -10 +75 °C 5.3 WiFi Specification (CR870 only) Feature Description WLAN Standards IEEE 802.11b IEEE 802.11g Frequency Band 2.412 – 2.472 GHz (2.4GHz ISM Band, 13 Channels) Channel 1 - Channel 13 North America, Japan Telec, Europe ETSI Modulation 802.11b mode (DS-SS: IEEE 802.11b) 802.11g mode (OFDM: IEEE 802.11g) Transmission Speed 802.11b mode 11Mbps, 5.5Mbps, 1Mbps 802.11g mode 54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 9Mbps, 6Mbps Tx Power 802.11b mode (16.5dBm, +/-1dBm) 802.11g mode (21dBm, +/-1dBm) Power-on Ramp < 2us RF Carrier Suppression < 15dBc TX EVM < -9dB @ 6Mbps < -25dB @ 54Mbps Rx Sensitivity (incl. CE2 Mother board) 802.11b mode =<-88dBm @ 1Mbps, =<-85dBm @ 5.5Mbps, =<-83dBm @ 11Mbps 802.11g mode =<-86dBm @ 6Mbps, =<-75dBm @ 36Mbps, =<-69dBm @ 54Mbps Throughput Rate (measured for each module) See factory test specification

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 14 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 6.1 RoHS Uses only RoHS compliant components 6.2 Environmental Test Withstands 4 hours at 70°C, 90% RH 6.3 ESD and Transient Test (Applies to LAN and USB external connections only) ESD: +/- 2kV operation, +/- 4kV no destruction (part of CE test) Fast electrical transients: +/- 500V operation, +/- 1000V no destruction (part of CE test) 6.4 Magnetic Field Test Passes EN55022 and EN55024 (part of CE test) 6.5 MTBF >10000 hours 6.6 Mechanical Specifications Passes drop test according to I.E.C. 68-2-32, height 100 cm, 1 corner, 6 faces. Passes vibration test with sine, vertical, 60 minutes, 600 to 18000 cpm, 1G 6.7 Module Quality Defect Rate: 7 months <0.5% failures, 14 months <1% failures AQL CR=0, MA=0.4, MI=0.4

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 15 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 7 Board Dimensions and Weight Note: For mechanical details of versions CR870-2C Mfg200 and CR870-2Q, please see the appropriate addendum: dat_CR860_CR870_3_3_datasheet_addendum_2C_Mfg200a.pdf or dat_CR860_CR870_3_5_datasheet_addendum_2Q.pdf. These addendums are available upon request from SMSC. 7.1 Top View and Side View of CR870 modules with PIFA antenna & no shields 7.2 Bottom View of CR870 modules with no bottom shield Note: 1. All dimensions are measured in millimetres (mm). 2. PCB’s thickness: 1.00 +/- 0.10mm 3. Tolerance: +/-0.10mm 4. Outline Tolerance: +/-0.10mm 5. NPTH Hole: +/-0.05mm 6. PTH Hole: +/-0.075mm 7. Connector positions, board dimensions, mounting hole positions and sizes are the same for all module variants. 8. Connector position tolerance: +/- 0.38mm Drawings shown: • With PIFA antenna • No top shield • No bottom shield RF section shield is always present in CR870 modules. Drawing shown: • With connector locations • No bottom shield

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 16 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 7.3 Top View and Side View of CR870 modules without PIFA antenna 7.4 Top View and Side View of CR870 modules with PIFA antenna & top shield Drawings shown: • Without PIFA antenna • No top shield • No bottom shield RF section shield is always present in CR870 modules. Drawings shown: • With PIFA Antenna • With top shield For versions without PIFA antenna, ignore PIFA antenna shown on the drawings in this section. RF section top shield is always present in CR870 modules.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 17 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 7.5 Module weight CR860: 25g CR870: 25g Note: Module weight applies to all versions of the module. 8 Connectors and Connections 8.1 WLAN UFL Antenna Connector (optional) One coaxial antenna connector is provided as an alternative to the built-in PIFA antenna. The choice between using the PIFA antenna or using the coaxial socket is a build option, determined by the position of a surface mount capacitor on the module PCB. Please see ordering guide for build option details. The surface-mount antenna socket used in the CR module is: UF.L type Ultra Small Surface Mount Coaxial Connector 8.2 Module Connectors The CR860/870 module uses 3 female board-to-board connectors as interfaces to the product main board. The connectors needed on the product main board are male type, with the part numbers as shown in the table below. Connector Number Connector Purpose Connector Type Number of Pins Pin Configuration Male Mating Connector Part Numbers J1 LCD 30 2 x 15 x 0.5mm 14-5046-030-145-829+ (Kyocera) J2 Media B2B Connector 120 2 x 60 x 0.5mm 14-5046-120-145-829+ (Kyocera)

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 18 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 8.2.1 Pin Descriptions Signal(s) Type Description POWER VIN(+3.3V) P Power supply input ; +3.3V. VIN (+1.2V) P Power supply input ; +1.2V. VIN_OUTSIDE(+1.9V) P +1.9V for powering RF section. This voltage is generated internally on the module from the 3.3V supply for all current module versions. Leave these pins open. 3V3RTC P The RTC function is no longer supported. This pin should be left open. GND P Ground (GND) connection for power supply 0V, signal returns and shielding. SPI SPI_DOUT O SPI data from DM870 to host controller. SPI_DIN I SPI data from host controller to DM870. SPI_CLK I SPI clock from host controller to DM870. Maximum recommended frequency is 2MHz, typical frequency is 1MHz. See Note 2 below. SPI_NCS0 I SPI chip select from host controller to DM870. PDOUT1 O This signal is used as SPI_REQ, SPI request signal, from DM870 to host controller for eDMP applications. Logic 1 indicates that there is an SPI message waiting to be read, the host controller should start the SPI clock and read any changed registers. Logic 0 indicates that all changed register messages have been read and the message buffer is empty. Also GPIO-06. SPI_NCS1 I Not used. Leave open. UART RXD1 I UART1 input to the DM870, used for shell access. SMSC recommends providing a connection to an external RS-232 transceiver and DB9 connector to connect to a PC COM port. Such a connection can be used for product development debugging, and for module programming control on the product manufacturing line and for module control during certification procedures. TXD1 O UART1 output from the DM870, used for shell access. SMSC recommends providing a connection to an external RS-232 transceiver and DB9 connector to connect to a PC COM port. Such a connection can be used for product development debugging, and for module programming control on the product manufacturing line and for module control during certification procedures. RXD0 I UART0 input. Optionally used for controlling an iPod via UART. TXD0 O UART0 output. Optionally used for controlling an iPod via UART.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 19 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL AUDIO AV2DATA0 O I2S or left justified audio data output. Typically connected to external D/A converter input or to external DSP for further audio processing. Used for main left and right channel audio output data. See Note 3. AV2CTRL0 O LRCK, audio data word clock at the audio sample rate (Fs). Maximum currently supported frequency is 192kHz. AV2CTRL1 O MCLK, audio master clock at 256Fs. This can be used to clock an external D/A converter or DSP. AV2CLK O SCLK, audio data bit clock at 64Fs. Allows for up to 32 audio data bits per sample word. AV4DATA1 O SPDIF format output. Can support samples rates up to 192kHz, so the maximum instantaneous frequency on this pin is 24.576MHz. AV4DATA0 I SPDIF input. Not used at present. Leave open. AV2DATA1 O I2S or left justified audio data output. Not used at present. Leave open. AOUTLP/AOUTLN, AOUTRP/AOUTRN O Differential stereo output from PWM-DAC, right and left channels. These signals require analog low pass filtering. SMSC is not recommending using the PWM-DAC outputs because of the potential for high out-of-band noise and uncharacterized audio quality. SMSC recommends using an external D/A converter connected to AV2DATA0. AV2DATA2 I I2S or left justified audio data input. Can be driven from an optional external A/D converter used to interface to iPod analog output or other analog audio sources. If not used, leave open. AV2DATA3 I I2S or left justified audio data input. Not used at present. Leave open. CONTROL NCS3 I BIST activate. Low-active input to invoke the Built In Self Test (BIST) function. This only applies to factory fresh modules. After JB2 firmware is loaded, this signal becomes GPIO-17 and is currently not used. DM870-internal pull-up. Leave this pin open. PDOUT0 I Factory Reset. GPIO-04. Return the CnE to factory settings. High-active input, DM870-internal pull-down. Pull to GND with a 10kohm resistor, unless return to factory settings from a hardware control is needed. Normally, return to factory settings is controlled from the host controller via SPI register. This pin is only monitored during the boot up process. VCO0 I Infrared sensor input. GPIO-05. This is a Schmitt-Trigger input and can handle inputs with slow slopes. Used for aDMP firmware builds for infrared remote control sensor output connection to DM870. For applications with a host controller, pull this pin to +3.3V via a 10kohm resistor. AV3CLK O ETH_NRESET Low-active reset for the on-board ethernet PHY. This output is driven by the DM870. GPIO-12. Leave this pin open. AV3CTRL0, AV3CTRL1 I/O I2C_SCL, I2C_SDA bus created by GPIO-13 and GPIO-14. No internal pull-ups; Use 4.7kohm pull up resistor on each pin to +3.3V. Maximum frequency is 400kHz. NRESET_MOD I Low-active input to reset the module. This signal must be driven by an external reset generator, or by a GPIO output from a host controller. See the application section of this datasheet for the timing requirements for NRESET_MOD. Includes internal 10K pull-up resistor to +3.3V. NPD_RF I Active low input to shut down the power for the 802.11 RF section. Internal 10kohm pull-up resistor to +3.3V. Leave open if powering down the RF section is not required.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 20 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL ETHERNET ETH_RX-, ETH_RX+, ETH_CT, ETH_TX+, ETH_TX- M Ethernet signals between the magnetics (transformer) on the module and the external RJ45 connector. See Note 4. Maximum bit rate is 100Mbps. ETH_LED_SPEED, ETH_LED_ACT O 3.3V push-pull outputs (max. ±12mA) to drive the ethernet LEDs. 100Mbps speed mode and activity are indicated by the outputs being low. Connect to LEDs through 220ohm resistors. USB USB_DN, USB_DP M USB data signals, normally connected to type A connector, USB switch or iPod dock connector. Maximum bit rate is USB High Speed at 480Mbps. USB_VBUS M Analog input for monitoring USB type A connector power. Connect to the +5V power which is driving the USB type A connector power pins. If this pin drops below 4.6V, then the DM870 will drive the USBVBUSDRV signal low to control an external power MOSFET to disconnect +5V power from the USB type A connector. See Note 5. USBVBUSDRV O Logic output to control an external MOSFET that is in series with USB type A connector power. See USB_VBUS above and Note 5. JTAG TMS,TCK,TDI, TDO I/O JTAG port for DM870. Leave open. SSM SSMD4, SSMD5, SSMD6, SSMD7 I/O Can be used to drive external shift registers to make extended GPIO signals (see Note 6), or as individual GPIO signals, or to make an SD card interface. SD card firmware is not supported at present in JB2. Can be mapped to GPIO #s 08,09,10,11. Leave open if not used. SSMD0, SSMD1, SSMD2, SSMD3, SSMCLK, SSMCP, SSMCMD, SSMWP I/O Used to make an SD card interface. SD card firmware is not supported at present in JB2. Leave open. VIDEO AV0CLK, AV0CTRL0, AV0CTRL1, AV0CTRL2, AV0DATA0, AV0DATA1, AV0DATA2, AV0DATA3, AV1DATA0, AV1DATA1, AV1DATA2, AV1DATA3 O ITU-R BT.656 digital video output signals. Optionally used to make a TVout menu display, or to display decoded album art. Can be connected to video D/A converter (see Note 7), or connected to a video DSP.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 21 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL GPIO (not already mentioned elsewhere in this table) A22 O GPIO18 Reserved for NOR flash address A22. Leave open. A23 O GPIO-16 Reserved for NOR flash address A23. Leave open. NWAIT I/O GPIO-15 Not currently assigned. Leave open. NCS2 I GPIO-19 Assigned to iPod dock connector iPod NDETECT. See Note 8. VCO1 I/O GPIO-07 Not currently assigned. Leave open. MMIICRS I/O GPIO-00 Not currently assigned. Leave open. MIICOL I/O GPIO-01 Not currently assigned. Leave open. MIITXER I/O GPIO-02 Not currently assigned. Leave open. MIITXCLK I/O GPIO-03 iPod dock connector Accessory Power signal. See Note 8. MII MIITXD0, MIITXD1, MIIRXD0, MIIRXD1 I/O Can be used, with GPIO signals above, to drive an external ethernet PHY. This is not supported by JB2 firmware. Leave open. LCD LCDD0, LCDD1, LCDD2, LCDD3, LCDD4, LCDD5, LCDD6, LCDD7, LCDD8, LCDD9, LCDD10, LCDD11, LCDD12, LCDD13, LCDD14, LCDD15, LCD16, LCDD17, LCDCLK, LCDCTRL0, LCDCTRL1, LCDCTRL2, LCDCTRL3 O Uses optional J1 LCD connector. Connect to local LCD display. See Note 9. Leave open if not used.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 22 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL Notes: 1. Signal type codes: I – 3.3V level Digital Logic Input into the DM870 O – 3.3V level Digital Logic Output from the DM870 IO – 3.3V level Digital Logic Input and Output (bi-directional) signal M – Miscellaneous, see text for description P – Power Supply 2. For SPI timing diagram for eDMP applications, please see: BridgeCo_JB2x - DeviceControlProtocol_Registers_v_2_1.pdf, or later version. For detailed setup and hold timing details, see DM870 IC datasheet: dat_DM870_16_datasheet.pdf, or later version. 3. For audio port timing diagrams, and for detailed setup and hold timing, please see DM870 IC datasheet: dat_DM870_16_datasheet.pdf, or later version. 4. For example ethernet external schematic, see: CR Module Ethernet_V1.0.pdf, or later version. 5. For example USB schematics, see: CR Module USB_V1.0.pdf, or later version. 6. For example use of extended GPIO shift registers, see CE2 schematic: A EVMCE2-4_schematic.pdf, or later version. 7. For example connection to a video D/A converter, see CE2 schematic: A EVMCE2-4_schematic.pdf, or later version. 8. iPod dock connector pin and GPIO assignments are under discussion. Please contact SMSC for recommendations for iPod dock connections to CR870 module. 9. For example connection to an LCD display, see CE2 schematic: A EVMCE2-4_schematic.pdf, or later version. 10. SMSC has a set of example motherboard schematics that shows example external circuitry that is typically connected to the module. Please check the SMSC/BridgeCo customer portal for a copy of these example schematics. Please check the SMSC/BridgeCo Customer Portal at https://portal.bridgeco.net/ DOWNLOAD area for the latest version of SMSC documents. If you do not have an account, please contact SMSC.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 23 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 8.2.2 Connector PIN Assignments J2 – Media Connector Function GPIO IC PIN Signal Signal IC PIN GPIO FunctionGND 1 2 GNDVIN (+3.3V) 3 4 VIN (+3.3V)VIN (+3.3V) 5 6 VIN (+3.3V)GND 7 8 GNDVIN (+1.2V) 9 10 VIN (+1.2V)VIN (+1.2V) 11 12 VIN (+1.2V)GND 13 14 GNDVIN_OUTSIDE (+1.9V) 15 16 VIN_OUTSIDE (+1.9V)GND 17 18 GNDF4 3V3RTC 19 20 GNDGND 21 22 TMS B20GND 23 24 TCK A20E17 SPI_DOUT 25 26 TDI B19F17 SPI_DIN 27 28 TDO A19D17 SPI_CLK 29 30 SPI_NCS0 D16C17 TXD0 31 32 SPI_NCS1 D15A18 RXD0 33 34 NRESET_MOD Module reset inputB17 RXD1 35 36 SSMD6 B16 GPIO-10 SPI_E_CLKA17 TXD1 37 38 SSMD4 C15 GPIO-08 SPI_E_SDOGND 39 40 SSMD2 A15SPI_E_NCS GPIO-11 C16 SSMD7 41 42 SSMD1 C14SPI_E_SDI GPIO-09 A16 SSMD5 43 44 SSMCMD A14B15 SSMD3 45 46 SSMWP C11B14 SSMD0 47 48NCS3M18GPIO-17BIST activateC13 SSMCLK 49 50 NCS2 L18 GPIO-19 iPod NDETECTC12 SSMCP 51 52 GNDGND 53 54 USB_VBUSA1 USB_DN 55 56 GNDB1 USB_DP 57 58 AOUTRN K2USBVBUSDRV 59 60 AOUTRP J2GND 61 62 GNDH3 AOUTLP 63 64 PDOUT1 L1 GPIO-06 SPI_REQJ3 AOUTLN 65 66 VCO1 L2 GPIO-07GND 67 68PDOUT0M1GPIO-04Factory resetGPIO-16 K20 A23 69 70VCO0M2GPIO-05IR inputGPIO-18 K19 A22 71 72AV3CLKU3GPIO-12ETH NRESETI2C SDA GPIO-14 V1 AV3CTRL1 73 74 AV0CTRL0 M3I2C SCL GPIO-13 V2 AV3CTRL0 75 76 AV1DATA3 P3K3 AV0CTRL2 77 78 AV1DATA2 R1L3 AV0CTRL1 79 80 AV1DATA1 R2N1 AV0CLK 81 82 AV1DATA0 R3N2 AV0DATA3 83 84 GNDN3 AV0DATA2 85 86 AV2CTRL1 T1 MCLKP1 AV0DATA1 87 88 GNDP2 AV0DATA0 89 90 AV2CLK R4 SCLKGND 91 92 GNDLRCK T2 AV2CTRL0 93 94 AV4DATA1 W2 SPDIF outputA/D data 1 T3 AV2DATA3 95 96 AV4DATA0 Y1 SPDIF inputA/D data 0 T4 AV2DATA2 97 98 GNDD/A data 1 U1 AV2DATA1 99 100 ETH_LED_ACTD/A data 0 U2 AV2DATA0 101 102 ETH_LED_SPEEDGND 103 104 MIICRS Y14 GPIO-00ETH_RX- 105 106 MIICOL W14 GPIO-01ETH_RX+ 107 108 MIITXER V10 GPIO-02ETH_CT 109 110 MIITXCLK V11 GPIO-03 iPod Access PowerETH_TX- 111 112 MIITXD0 W10ETH_TX+ 113 114 MIITXD1 Y10GND 115 116 MIIRXD0 W12Free GPIO-15 N18 NWAIT 117 118 MIIRXD1 Y12NPD_RF119120GNDUSBVideo OutputEthernetUSBVideo OutputEthernetPIN NumberSPIDebug UARTJTAGSPI Note: The IC PIN column indicates the pin number on the DM860 or DM870 integrated circuit. This allows for easy cross-reference to the DM860 or DM870 datasheet information.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 24 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL J1 – LCD Connector Function GPIO IC PIN Signal Signal IC PIN GPIO FunctionGND12GNDY7 LCDD034LCDD1 W7V7 LCDD256LCDD3 Y6W6 LCDD478LCDD5 V6U6 LCDD6910LCDD7 Y5W5 LCDD81112LCDD9 V5U5 LCDD101314LCDD11 Y4W4 LCDD121516LCDD13 V4U4 LCDD141718LCDD15 Y3W3 LCDD161920LCDD17 Y2GND2122GNDY9 LCDCLK2324LCDCTRL0 W9Y8 LCDCTRL12526LCDCTRL2 W8V8 LCDCTRL32728GNDGND2930GNDPIN NumberLCD InterfaceLCD InterfaceLCD InterfaceLCD Interface Note: The IC PIN column indicates the pin number on the DM860 or DM870 integrated circuit. This allows for easy cross-reference to the DM860 or DM870 datasheet information. 9 Application Guidelines 9.1 Power Supply sequencing and Reset Timing There are strict power sequencing and reset timing requirements. • Power up the I/O voltage (3.3V) first and hold NRESET_MOD low. • The core voltage (1.2V) must never be higher than (I/O voltage +0.5 V). • The core voltage (1.2V) must be within the specified core voltage limits less than 300ms after the I/O voltage (3.3V) reaches the specified I/O voltage limits. • Throughout the power down process, the 3.3V supply must maintain a higher voltage than the 1.2V supply, until both have reached ground potential. • To assure a proper IC reset, the power supplies must be present for a minimum time of 2ms before NRESET_MOD is de-asserted. Please see the power and reset timing figure in Section 9.1.1 below.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 25 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL 9.1.1 Power up, Reset and Power Down Timing TimeVoltageNRESET_MOD0V+1.2V+3.3V< 300ms>= 2msPower Up Power Down 9.2 RF Considerations Note that overall system, RF and WiFi performance is significantly affected by the product design, environment and the application. It is the responsibility of the product designer to ensure proper system level shielding (if required) and to verify performance and fitness for the given product features and applications. The WiFi performance will be affected by the RF environment surrounding the CR module. Please ensure that the CR module is positioned in a “quiet” RF environment, as far away as possible from high frequency clock signals and any other sources of RF energy. Also, make sure the antenna is not shielded by any metal objects, for example loudspeakers or other metal parts. Please make sure that the power supplies, in particular the +1.9V supply, are quiet and free from noise. SMSC recommends that systems implementing AirPlay should use a module configuration that includes top module shielding, as well as paying particular attention to system configuration and shielding.

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 27 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL Revision Date / Author Details of Change Reason for Change V3.5 b May 15, 2011 / SHs • Updated the Feature list on Cover page • Updated J1 & J2 “Connector PIN Assignments” tables: removed Power column & re-organised columns + added Notes • Changed “Application Notes” title to “Application Guidelines” • Updated Copyright date to “2011” • Updated Table of Contents font styling • Updated “Electrical Specifications” table: new logic I/O values • Updated Top View of CR870-2A Board Picture: removed “Optional socket” label + added a Note • Updated Bottom View of CR870-2A Board Picture: added a Note + labelled “+1.9V DC to DC converter” • Added Note 11 to the “Pin Descriptions” section • Updated “Regulatory Compliance and Quality” table: updated the Module Versions Passed for Radio Regulations • Removed text before “Pin Descriptions” table V3.5 a May 6, 2011 / SHs • Updated “Power up, Reset & Power down Timing” figure V3.5 May 5, 2011 / SHs • Added note to Module Weight section • Updated the Ordering Guide – added new Q & R versions & shaded version K • Updated appropriate Board Picture section titles with new versions • Added note to “Board Dimensions and Weight” section • Updated text in the “Power Supply sequencing and Reset Timing” section • Added new Power Supply & Timing figure • Updated the Key Connections table • Updated “Key Connections” section title to “Pin Descriptions” • Updated “Detailed Connector PIN Descriptions” section title to “Connector PIN Assignments” • Updated J2 Media Connector table • Re-imported Block Diagram as a wmf file V3.4 b March 3, 2011 / SHs • Updated J2 Media Connector table • Updated Block Diagram V3.4 February 5, 2011 / SHs • Updated “Ordering Guide” – added CR870-2P configuration, CR870-2M to 32MB SDRAM • Updated Board Pictures subsection titles – 3.4 & 3.5

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 28 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL Revision Date / Author Details of Change Reason for Change V3.3 c January 24, 2011 / SHs • Updated “Board Pictures” subsection titles & notes – removing mention of Mfg code • Updated “Ordering Guide” – removed Mfg column, fixed Top Shielding column V3.3 b January 22, 2011 / SHs • Updated “Board Pictures” subsection titles • Added text to “Board Pictures” subsections • Updated “Board Dimensions and Weight” subsection titles • Added text to “Board Dimensions and Weight” subsections • Removed all references to “DAB” as this option is no longer available • Updated Block Diagram by removing DAB block and moving USB switch • Updated Application Notes – RF Considerations section • Updated the Ordering Guide table with L, M, N, O configurations and new explanatory shading V3.3 January 14, 2011 / SHs • Updated “Board Pictures” section sub-section titles • Updated “Top View of CR870-2F Mfg 100, CR870-2G Mfg 101, CR870-2I Mfg 100, CR870-2J Mfg 100, CR870-2K Mfg 100” section board image • Removed “Bottom View of CR870-2C Mfg 200” section and associated image • Updated Ordering Guide – removed CR870-2C Mfg 200 row and Bottom Module Shielding column • Updated “Board Dimensions and Weight” section sub-section titles • Removed section 7.4.2 – “Bottom View” and associated image • Updated Side View drawing in “Top View and Side View of CR870 modules with top shields, with PIFA antenna” section V3.2 b January 11, 2011 / SHs • Updated Application Notes section with new subsections – “Power Supply sequencing and Reset Timing” & “RF Considerations” • Updated subsection titles for Board Pictures section • Updated subsection titles for Board Dimensions and Weight section • Updated Ordering Guide with CR870-2K options V3.2 January 3, 2011 / SHs • Updated the Ordering Guide

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 29 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL Revision Date / Author Details of Change Reason for Change V3.1 December 3, 2010 / SHs • Added Top and Bottom View images of new CR870-2C Mfg 200 • Added mechanical drawings of new CR870-2C Mfg 200 • Updated the Ordering Guide with CR870-2C Mfg 200 information V3.0 August 13, 2010 / SHs • Added Page Numbers to pages 1-3 • Moved “Module Revision History” section to underneath “Revision Control” table • Removed © from Table of Contents • Added a Note to Section 3.3 – Top View of CR870-2G • Amended Section 3.4 title to include more versions – Bottom View • Updated Section 7.1 title to say “with PIFA Antenna” • Updated Section 7.3 title to say “without PIFA Antenna” • Updated “Regulatory Compliance” table • Added Note underneath “Regulatory Compliance” table V3.0 July 22, 2010 / SHs • Add mechanical tolerances note to “Board Dimensions and Weight “ section • Updated Key Connections table with audio outputs data • Added section numbering • Added Table of Contents V2.15 July 4, 2010 / SHs • Updated “Ordering Guide” table V2.14 June 10, 2010 / SHs • Updated Frequency Band entry in “WiFi Specification” table V2.13 June 6, 2010 / SHs • Updated “Ordering Guide” table V2.12 May 27, 2010 / SHs • Updated TX EVM entry in “WiFi Specifications” table • Updated Power Consumption entries in “Electrical Specifications” table • Added Note to “Electrical Specifications” table • Removed box from “Bottom View of CR870-2C version” photo • Updated “Bottom View of CR870-2C version” title to “Bottom View of CR870-2B, CR870-2C, CR870-2G versions” • Added “Top View of CR870-2G version” photo • Updated “Top View” title to “Top View of CR870-2A version” • Updated “Bottom View” to “Bottom View of CR870-2A version” • Updated Notes in Board Dimensions section

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 30 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL Revision Date / Author Details of Change Reason for Change • Added “Top and Side View of CR870-2G” drawings • Updated Module Weight titles V2.11 April 25, 2010 / SHs • Updated Power Consumption/WLAN Operating entry in “Electrical Specifications” table V2.10 April 10, 2010 / SHs • Corrected “Module Connectors” section text to say “female board-to-board connectors” • Updated Module Connectors table with correct “Male” Mating Connector Part Numbers V2.9 March 22, 2010 / SHs • Renamed “WLAN Antenna Connectors” section to “WLAN UFL Antenna Connector” • In the “WLAN Antenna Connectors” table, “receptible” became “receptacle” • CR870-2G option and External Antenna UFL connector column added to Ordering Guide • Power Consumption values added to Electrical Specifications table • Added Absolute Maximum Ratings table • Added Application Notes section • NREST became NRESET_MOD for Pin 34 in Key Connections table • SPI_REQ row added to Key Connections table • SPI_REQ added to Function column of Pin 64 in J2-Media Connector table V2.8 Feb. 24, 2010 / SHs • Added “Bottom View of CR870-2C version” image to “Overview” section V2.7 Feb. 16, 2010 / SHs • Updated “Module Connectors” table V2.6 Feb. 15, 2010 / SHs • Updated “Ordering Guide” table V2.5 Feb. 10, 2010 / SHs • Updated “Ordering Guide” table • Added new coaxial text in “WLAN Antenna Connectors” section • Added manufacturer name to “Module Connectors” table V2.4 Feb. 08, 2010 / SHs • Updated Rx Sensitivity description in “WiFi Specification” table V2.3 Feb. 03, 2010 / SHs • “Key Connectors” table title changed to “Key Connections” • Updated entries in “Key Connections” table • Updated pins 1, 2, 25, 27, 58 & 60 in “J2 – Media Connector” table

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 31 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL Revision Date / Author Details of Change Reason for Change V2.2 Feb. 02, 2010 / SHs • Added new items to “WiFi Specification” table • Amended Block Diagram to show input of 1.2V instead of 1.8V V2.1 Jan. 04, 2010 / SHs • Updated header layout • Removed “CR860/CR870” from datasheet title • Left justified Key Features list on front page • New Ordering Guide table • Updated Module Weights V2.0 Jan. 02, 2010 / JWs and SHs • New header and footer layout • Fit front and back Overview images onto one page • Bulletise Revision Control table V1.1 Dec. 18, 2009 / SHs • Changed Core Module name to “JukeBlox Networked Media Module(CR Series)” • Front page revisions: removed front and back images of board; inserted angled image of board; moved Key Features list to front page • Moved Disclaimers page to end of document • Replaced previous board images (front and back) in Overview section with better quality images • Added box and label to BridgeCo processor in Overview images • Revised Ordering Guide • Reduced Board Dimension drawings to fit on one page • Added mating connector part numbers to Module Connectors section. V1.0 Dec. 9, 2009 / SHs Initial version

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 32 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTFEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTFEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTFEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. CAUTION:CAUTION:CAUTION:CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. Labeling requirementsLabeling requirementsLabeling requirementsLabeling requirements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RF exposure warningRF exposure warningRF exposure warningRF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Information for the OEMs and IntegratorsInformation for the OEMs and IntegratorsInformation for the OEMs and IntegratorsInformation for the OEMs and Integrators

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 33 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. This device is intended for OEM integrators only. Please See the full Grant of Equipment document for other restrictions. This device must be operated and used with a locally approved access point. Information To Be Supplied to the Information To Be Supplied to the Information To Be Supplied to the Information To Be Supplied to the End User by the OEM or IntegratorEnd User by the OEM or IntegratorEnd User by the OEM or IntegratorEnd User by the OEM or Integrator The following regulatory and safety notices must be published in documentation supplied to the end user of the product or system incorporating an adapter in compliance with local regulations. Host system must be labeled with "Contains FCC ID:PPQ-CR8702N“, FCC ID displayed on label. Canada, Industry Canada (IC) NoticesCanada, Industry Canada (IC) NoticesCanada, Industry Canada (IC) NoticesCanada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure InformationRadio Frequency (RF) Exposure InformationRadio Frequency (RF) Exposure InformationRadio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person's body). This device has been certified for use in Canada. Status of the listing in the Industry Canada’s REL (Radio Equipment List) can be found at the following web address: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng Additional Canadian information on RF exposure also can be found at the following web address: http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html Canada, avis d'Industry Canada (IC)Canada, avis d'Industry Canada (IC)Canada, avis d'Industry Canada (IC)Canada, avis d'Industry Canada (IC)

JukeBlox Networked Media Modules – CR Series Datasheet SMSC CR860/CR870 34 Revision 3.8 (01-11-12) SMSC CONFIDENTIAL Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. Informations concernant l'exposition aux frInformations concernant l'exposition aux frInformations concernant l'exposition aux frInformations concernant l'exposition aux fréquences radio (RF)quences radio (RF)quences radio (RF)quences radio (RF) La puissance de sortie émise par l’appareil de sans fil Dell est inférieure à la limite d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de sans fil Dell de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition à des appareils mobiles (les antennes se situent à moins de 20 cm du corps d'une personne). Ce périphérique est homologué pour l'utilisation au Canada. Pour consulter l'entrée correspondant à l’appareil dans la liste d'équipement radio (REL - Radio Equipment List) d'Industry Canada rendez-vous sur: http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch.do?lang=eng Pour des informations supplémentaires concernant l'exposition aux RF au Canada rendez-vous sur : http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

Navigation menu

Upload a User Manual

Namespaces

Wiki Guide
HTML
PDF
Info

Views

User Manual
Discussion / Help

Navigation

© 2024 UserManual.wiki | Privacy Policy

Contact Us
DMCA