LITE ON TECHNOLOGY WN4517L 802.11a/b/g/n/ac, 2T2R Wireless LAN USB2.0 Module User Manual 05

Download:
Mirror Download [FCC.gov]
Document ID	3269850
Application ID	XrCQwhiFs3GtICz3J3MgdA==
Document Description	User manual Warning statement
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.26kB (128228 bits)
Date Submitted	2017-01-25 00:00:00
Date Available	2017-01-25 00:00:00
Creation Date	2017-01-11 05:14:16
Producing Software	Acrobat Distiller 9.5.5 (Windows)
Document Lastmod	2017-01-11 05:14:16
Document Title	Microsoft Word - 05.User manual-警語
Document Creator	PScript5.dll Version 5.2.2
Document Author:	User

FCC Statement:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.
This device and its antenna(s) must not be co‐located with any other transmitters except in
accordance with FCC multi‐transmitter product procedures.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20
cm between the radiator & your body.
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is responsible for the
compliance to all the rules that apply to the product into which this certified RF module is
integrated.
Additional testing and certification may be necessary when multiple modules are used.
20 cm minimum distance has to be able to be maintained between the antenna and the
users for the host this module is integrated into. Under such configuration, the FCC radiation
exposure limits set forth for an population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20
cm separation with the antenna while this end product is installed and operated. The end
user has to be informed that the FCC radio‐frequency exposure guidelines for an
uncontrolled environment can be satisfied. The end user has to also be informed that any
changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment. If the size of the end product is smaller than 8x10cm,
then additional FCC part 15.19 statement is required to be available in the users manual:
This device complies with Part 15 of FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC
ID: PPQ‐WN4517L ". If the size of the end product is larger than 8x10cm, then the following
FCC part 15.19 statement has to also be available on the label: This device complies with
Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.
OEM Integrator Checklist
The party below will implement the LITE‐ON Module in host systems in accordance with the
instructions specified in this document and the documents referenced herein.
1. The OEM integrator will ensure the Module is integrated in a host systems using only the
approved antenna model(s) described in this document.
WiFi_1：Walsin / RFMTA200700NNLB002 / PIFA Antenna / 2.4G Gain: 2.48 dBi, 5G Gain: 2.95
dBi
WiFi_2：Walsin / RFMTA340740IMLB701 / PIFA Antenna / 2.4G Gain: 2.30 dBi, 5G Gain: 4.36
dBi
2. The OEM integrator will ensure the antenna placement inside the host system will
maintain the required spacing to end user for RF Exposure compliance, as specified in this
document.
3. If other radios are integrated inside the host with the LITE‐ON Module, the OEM
integrator will contact its test lab, TCB or LITE‐ON to determine if additional FCC compliance
evaluation is required to meet FCC collocation rules.
4. The OEM integrator will ensure end user documentation will contain the specified
regulatory wording and ensure the host system and the Module itself are labeled as
specified in this document.
5. The OEM integrator will ensure the Module is programmed in the factory with compliant
transmit power not exceeding the levels specified in this document.
LITE‐ON requests that the OEM integrator acknowledge its receipt of this document and the
above instructions. You may contact LITE‐ON with any questions concerning this document
or the responsibilities of the OEM integrator.
IC Statement:
This device complies with Industry Canada license‐exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
For product available in the USA/Canada market, only channel 1~11 can be operated.
Selection of other channels is not possible.
Pour les produits disponibles aux États‐Unis / Canada du marché, seul le canal 1 à 11
peuvent être exploités. Sélection d'autres canaux n'est pas possible.
This device and its antenna(s) must not be co‐located with any other transmitters except in
accordance with IC multi‐transmitter product procedures.
Refering to the multi‐transmitter policy, multiple‐transmitter(s) and module(s) can be
operated simultaneously without reassessment permissive change.
Cet appareil et son antenne (s) ne doit pas être co‐localisés ou fonctionnement en
association avec une autre antenne ou transmetteur.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
potential for harmful interference to co‐channel mobile satellite systems.
les dispositifs fonctionnant dans la bande 5150‐5250 MHz sont réservés uniquement pour
une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux.
The maximum antenna gain permitted for devices in the band 5725‐5850 MHz shall be such
that the equipment still complies with the e.i.r.p. limits specified for point‐to‐point and
non‐point‐to‐point operation as appropriate.
le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725‐5850 MHz)
doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non
point à point, selon le cas.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250‐ 5350 MHz,
5470‐5600 MHz and 5650‐5725 MHz.
Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes
5250‐5350 MHz, 5470‐5600 MHz et 5650‐5725 MHz.
The maximum antenna gain permitted for devices in the bands 5250‐5350 MHz and
5470‐5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit.
le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250‐5350 MHz et
5470‐5725 MHz doit se conformer à la limite de p.i.r.e.
Users should also be advised that high‐power radars are allocated as primary users (i.e.
priority users) of the bands 5250‐5350 MHz and 5650‐5850 MHz and that these radars could
cause interference and/or damage to LE‐LAN devices.
De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute
puissance sont désignés utilisateurs principaux (c.‐à‐d., qu’ils ont la priorité) pour les bandes
5250‐5350 MHz et 5650‐5850 MHz et que ces radars pourraient causer du brouillage et/ou
des dommages aux dispositifs LAN‐EL.
Pour une utilisation en intérieur uniquement.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS‐102 radiation exposure limits set forth for an
uncontrolled
environment. This equipment should be installed and operated with minimum distance 20
cm
between the radiator & your body.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum
de 20 cm de distance entre la source de rayonnement et votre corps.
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC
compliance requirement of the end product, which integrates this module.
Any changes or modifications not expressly approved by the manufacturer could void the
user's authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20
cm separation with the antenna while this end product is installed and operated. The end
user has to be informed that the IC radio‐frequency exposure guidelines for an uncontrolled
environment can be satisfied. The end user has to also be informed that any changes or
modifications not expressly approved by the manufacturer could void the user's authority to
operate this equipment. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX IC:
4491A‐WN4517L ".

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : User
Create Date                     : 2017:01:11 05:14:16+08:00
Modify Date                     : 2017:01:11 05:14:16+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : PScript5.dll Version 5.2.2
Producer                        : Acrobat Distiller 9.5.5 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - 05.User manual-警語
Creator                         : User
Document ID                     : uuid:d0ee8452-69eb-4bfc-b9ac-0a85f9c36750
Instance ID                     : uuid:c6ed3cdd-2a59-4647-acfe-b0155a1e8ffe
Page Count                      : 6

EXIF Metadata provided by EXIF.tools