LITE ON TECHNOLOGY WP8333V1 802.11ac Tri Band PoE Access Point User Manual

LITE-ON Technology Corp. 802.11ac Tri Band PoE Access Point

User Manual

C-110 Mojo Access Point / SensorQuick Start GuidePackage ContentsYou should have received the following components in your C110 package.C110 15/16” (24mm) Mounting Bracket
Mounting the C-1104. Rotate the device such that all the mounting posts on the rear-side of the device are snapped in to the respective notches on the bracket.2. Rotate bracket to snap on to T- Grid.1. Aix bracket to T - Grid.3. Place the irst mounting post on the rear-side of the device on to the lower notch of the bracket.
Getting the C-110 OnlineStep 1: Power upIf using PoE, plug one end of the Ethernet cable into the PoE switch or injector and plug the other end into the Ethernet + PoE port (LAN1) on the C110. Make sure the PoE source you are using is turned ON.ORAs an alternative to PoE, insert the power adapter plug into an AC power outlet and the other end into the power input port on the C110.Warning: If not using PoE, make sure you use only an AC power adapter supported by the C110 access point (AP).Step 2: Connect to the networkIf you are using PoE, then the C110 should already be connected to your network. If you are not using PoE, then plug one end of the Ethernet cable into an Ethernet jack on your network and the other end into the Ethernet port (LAN1) on the C110.Step 3: Check the LED statusWait for a few minutes till theLEDs for Power and Ethernet (LAN1) turn solid GREEN, which indicates that the C110 is online and operational.
TroubleshootingThe following table provides the status of the device based on the LEDs.After following these guidelines, if you are still unable to resolve the problem, contact thelocal Mojo Networks Sales Engineer or 24/7 Mojo Networks Technical Support.Tel: +1 (650) 641 0027 Email: support@mojonetworks.comMojo Networks, Inc. 339 N. Bernardo Avenue #200, Mountain View, CA 94043T +1.877.424.7844 T 650.961.1111 F 650.961.1169 www.mojonetworks.com info@mojonetworks.com© 2016 Mojo Networks, Inc. All rights reserved. Mojo Networks and the Mojo Networks logo are trademarks, and Mojo is a registered trademark of Mojo Networks, Inc. All other trademarks mentioned herein are properties of their respective owners. Speciications are subject to change without notice.LED Status DescriptionPower Solid Green Power OnO Power OLAN1/PoE Solid Green Device connected to LAN port 1 at 10/100/1000 MbpsBlinking Green Activity on LAN port 1LAN2 Solid Green Device connected to LAN port 2 at 10/100/1000 MbpsBlinking Green Activity on LAN port 22.4 GHzSolid Green Client connected to 2.4 GHz radioBlinking Green Wireless activity on 2.4 GHz radio5 GHz Solid Green Client connected to 5 GHz radioBlinking Green Wireless activity on 5 GHz radioRadio 3 Blinking Green Activity on third radio If the AP is not able to connect to Mojo Wireless Manager, check the following:1. Ensure that the Ethernet cable is plugged into the correct port on the C110 and the other end of the cable is plugged into an Ethernet jack or port on a switch that is turned ON.2. If the C110 did not receive a valid IP address from the DHCP server, ensure that a DHCP server is ON and available on the VLAN/subnet to which the AP is connected. If the AP still fails to get a valid IP address, reboot it once to see if that resolves the problem.3. If you are using Mojo Cloud Services, ensure that Internet connectivity is available from the VLAN/subnet to which the AP is connected. Check if the required ports for AP and Server communication – UDP 3851 and default HTTP (TCP port 80) – are open on the Firewall. If you are using a Proxy, Web accelerator or URL content iltering, ensure the settings allow communication between the AP and Mojo Cloud Services.
For indoor use only.Pour une utilisation en intérieur uniquement.Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz.Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz.
This device is restricted for indoor use.

Navigation menu