8
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 42969 |
| Application ID | dOrPXWLTIKIqxDTtyxgRsA== |
| Document Description | 8 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 10.25kB (128102 bits) |
| Date Submitted | 1999-06-17 00:00:00 |
| Date Available | 1998-06-15 00:00:00 |
| Creation Date | 2001-06-20 17:57:13 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-06-20 17:57:19 |
| Document Title | 42969.pdf |
| Document Author: | VicodinES /CB /TNN |
USER MANUAL
PCI — SOUND CARD
March 1998
FCC
Version 1.0
Ago/P/o
FEDERAL COMMUNICATIONS COMMISSION (F.C.C.) STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation,
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and , if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation, if
this equipment does cause harmful interference to radio or television reception, which can be determined by
hurling the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
1. Reorient / Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver,
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
ea
4. Consult the dealer or an experienced radio/ TV technician for help.
NOTE: 1. The use of a non-shielded interface cable with this equipment is prohibited.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
PCI Sound Card
TABLE OF CONTENTS
I. DESCRIPTION ................................ 2
1.1. FEATURES ..............
1.2. CARD FIGURE .
1.3. CONNECTORS..
1.3.1. Etternal Connectors‘ .
1,3 2. [VI/Erna] Connectors
1.3 3. Audio Conneclors:..
2. HARDWARE INSTALLATION ..... ........... .......
2.1. HANDLING THE PCI SOUND CARD...
2.2. INSTALLING THE PCI SOUND CARD ..
3. SOFTWARE INSTALLATION ..................................
31. SOFTWARE CONTENTS ................................................
3.2. DEVICE DRIVER INSTALLATION UNDER WINDOWS 95
Awwwwm
UI
anal/d:-
Page - 1
PCI Sound Card
1. DESCRIPTION
This is a new audio adapter that provides the next generation ofPCl audio performance to
the PC market. The adapter not only meets the new demands of advanced PC audio
applications but also enables the integration of a complete multimedia subsystem on a
single adapter. The adapter functionality and interfaces are compliant with all major
industry standards, including the Sound Blaster Compatible, FC97, Windows 95 Direct
Sound, Windows Sound System and PCl 2.1 bus specification.
1.1. Features
PC] 2.1 compliant
PC] Bus Power Management rev. 1.0 compliant
PCI Bus master for PC[ Audio
True Full Duplex Playback and Capture with different Sampling Rate
Maximum 6mm: XG capital Wavetable Synthesizer including
GM compatibility
Direct Sound Hardware Acceleration
Direct Music Hardware Acceleration
: Downlondable Sound (DLS) level-l
Legacy Audio compatibility
5 Genuine OPL3
=> Hardware Sound Blaster Pro compatibility
:> MPUAOI UART mode MIDI interface
:> Joystick
Supports PC/PCI and distributed DMA {or Legacy
DMAC (8237) emulation
Support: I’ S serial input port for Zoomed Video port (optional)
Supports Consumer lEC958 Output (SPDIF) port
Supports AC-l interface (AC-Link)
Single Crystal operation (24.576 MHz)
SV Power supply for 110. 3.3V Power supply for internal core logic
Compliant with AC’97 Requirements
= 4 Stereo Inputs: Ll'NE, CD, VIDEO, AUX
: TAD connector for mono In and Output for modern Audio
3 l MlC Input
r.» Stereo LINE Output/ Speaker Output
20 dB MIC Amplifier
Analog Characteristics
= A/D SN: 35 dB
2 WA S/N: 90 dB
Low Power Consumption
6 Watt Power Amplifier
UUUUU
PCI Sound Card
1.2. Card Figure
ran-m wt mo with
mun
mm all m m MIMI-Mr
mun-t
tac- 4”; “MA-hm-
ttttsr
uler an mom...-
got...»-
mm...,,, M
v m
llIIIIIIIIIIllIIIIIIIlIIIIIIIlIIIl
1.3. Connectors
This PCI Sound Card includes up to seven internal connectors, four external Jack Ports, one
external MIDI/ Joystick connector, one VIDEO connector, one VOICE Modem connector,
one IZ S Interface, and one PC-PCI Legacy AUDIO SIDEBAND SIGNAL connector.
1.3.1. External Connectors:
ta 3 5mm Phone Jack for LINE
2; 3 5mm Phone Jack for MIC
z 3 5mm Phone Jack (at LINE our.
to 3 5mm Phone lack fot SPEAKER out.
o. Connector for MIDI/JOYSTICK
1.3.2. Internal Connectors:
nlemnl conncclor for LINE IN. (oplicnal)
nlcmal conucclm for MIC IN. (optional)
Js lnlemal conneclor for LINE our, (optional)
mental connector for SPEAKER our. (ophonal)
onnecwr for ID]: CD-RODI Al'DlO (ATAPI)
unneclor for ID}: (tn-Rom AUDIO usn
Conncclor for AUX.
onnecIoI fat TAD/VOICE MODEM.
onnootor for VIDEO [NI
Dnnccmr for I 5 Interface (optional)
onneclor InI PC-I’Cl Legacy Audio SIDEBAND SIGNAL.
Page - 3
PCI Sound Card
1.3.3.
JID:
JII:
Jll:
113:
JM:
Jls:
JIfl:
ATAPI
CD—Andia
CD—Andin
AUX
TAD/Voice Madam
VIDEO IN
I! s lnlarflu
PC—PCI
Audio Connectors:
RGGL
L: LEFT CHANNEL SIGNAL
. ROUND
R: RIGHT CHANNEL SIGNAL
L: LEFI' CHANNEL SIGNAL
. ROUND
R: RIGHT CHANNEL SIGNAL
L; LEFT CHANNEL SIGNAL
6: GROUND
R: RIGHT CHANNEL SIGNAL
PHONE IN
GROUND
GROUND
MONO OUT
sun...
: LEI-T CHANNEL SIGNAL
: GROUND
R: RIGHT CHANNEL SIGNAL
nt-
SERIAL DATA I
SERIAL CLOCK
SERIAL DATA 0
GROUND
sun.-
PCGNT fl
GROUND
N. ,
PCREQ#
GROUIND
sERIRQfl
mw5UN_
2. HARDWARE INSTALLATION
2.1.
PCI Sound Card
Handling the PCI Sound Card
WARNING: Static electricity can damage your equipment. Do not take the card out o
f its
static protective bag until you are ready to work with it.
Follow these precautions when handling the card:
0 Before you open the static protective bag, touch it to a metal expansion slot cover on
the back of your computer. This drains static electricity from the package and from your
body.
- Do not touch any exposed printed circuitry afier opening the package.
- Keep other people from touching the card. They might have a static-electricity buildvup,
- Limit your movement. Movement causes a build—up of static electricity.
2.2.
Step 1.
Step 2,
Step 3.
Step 4.
Step 5.
Step 6.
Step 7.
Installing the PCI Sound Card
Turn off the system and all peripheral devices.
Disconnect the power cord and all peripheral devices from the system.
Remove the system cover and identify an unused PCI slot.
Unscrew the slot cover plate, plug in the PCI Sound Card, and tighten it
with the screw.
Ifyou have speakers or amplifiers, plug the cable into the J1 or JZ Jack on
the back ofthe Sound Card.
Depending on what type ofCD Audio cable you have connect J10 or J] 1
on the Sound Card and the Audio output at the back ofthe CD-ROM drive.
Make sure pin 1 own) or Jll is connected to the leflmost pin of the CD-
ROM Audio output.
Put back the system cover, reconnect the system power cord and all
peripheral devices. Check and make sure all connections are correct before
you turn on the system.
PCI Sound Card
3. SOFTWARE INSTALLATION
3.1. Software Contents
There is one CD‘title which comes with this package, labeled:
“Device Driver for Win 95"
This CD-title includes the necessary device driver for Win95 which you may use.
3.2. Device Driver Installation Under Windows 95
To install the device driver under Windows 95, please follow the steps below:
1.) Aficr you have installed the PC] Sound Card, restart your Windows 95 system.
2.) The "New Hardware Found" dialog box will display the message "PCI Multimedia
Audio Device". Choose the option "Driver from disk provided by hardware
manufacturer”.
3.) To continue the driver installation, select the appropriate CD-ROM letter and the root
directory, for example “E:\Win95”.
4.) Make sure the dialog box specifies the correct CD-ROM letter and click OK, This will
start the copying process,
5) Follow the on screen instructions and you should be able to install the device driver
easily,
FCC
Version 1.0
Page ~ 6
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2001:06:20 17:57:13 Producer : Acrobat Distiller 4.0 for Windows Author : VicodinES /CB /TNN Title : 42969.pdf Modify Date : 2001:06:20 17:57:19-04:00 Page Count : 8EXIF Metadata provided by EXIF.tools