8
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 44559 |
| Application ID | XFGKmhnz/rCUdbaiLJlBYQ== |
| Document Description | 8 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 17.12kB (213973 bits) |
| Date Submitted | 1999-06-28 00:00:00 |
| Date Available | 1998-07-08 00:00:00 |
| Creation Date | 2001-06-21 14:58:22 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-06-21 14:58:29 |
| Document Title | 44559.pdf |
| Document Author: | VicodinES /CB /TNN |
USER MANUAL
ISA — SOUND CARD
March 1998
A-115-0054
Version 1.0
ABMFW
Pl“? 6? P144 Sound Card
The inrnrmiiiion in this document I! subject
to change wlilimii nolict
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 ofthe FCC mles. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. lfthis equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more ofthe following
measures:
I Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
I Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
I Consult the dealer or an experienced radio/TV technician for help.
Use only shielded cables to connect l/O devices to this equipment.
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.
Note:
The user may find the following booklet prepared by the Federal Communications
Commission helpful:
" How to Identify and Resolve Radio-TV Interference Problems. "
This booklet is available from the U.S. Government Printing Office,
Washington, DC 20402
Stock No. 004-000-00345-4.
All brands and trademarks are registered by their respective companies
Printed in Taiwan
M {Pay Sound Card
TABLE OF CONTENTS
1. DESCRIPTION ......
1.1. FEATURES ..
1,2. APPLICATIONS
1.3. SYSTEM REQUIREMENTS
I 4. CARD FIGURE.
1.5. CONNECTORS.
l 5.1. Slandard C ormecmn.
1 5 z Ofillcmalf‘onflzdorx
1 5 3 AudIo Carma/arr.
2. HARDWARE INSTALLATION .......................................................
2. I. HANDLING THE AVANCE LOGIC ALSIZO SOUND CARD
2.2. INSTALLING THE AVANCIE LOGIC ALS [20 SOUND CARD ......
3. SOFTWARE INSTALLATION ..........................................
3.1. SOFTWARE CONTENTS .....
3.2. SOFTWARE DRJVER INSTALLATION UNDER WINDOWS® 3.1
3.3. SOFTWARE DRIVER INSTALLATION UNDER DOS.
3.4. SOFTWARE DRIVER INSTALLATION UNDER WINDOWS® 9
3.5. SOFTWARE DRIVER INSTALLATION UNDER WINDOWS® NT 3.51/40
2.»
ng'alniaiuh
u-
oeslslmm ax thin
PEI“ - 2
7529 47 P144 Sound Card
1. DESCRIPTION
This is a 16-bit PC stereo sound card using the AVANCE LOGIC ALSIZO chipset
with the Bundle Software “SOFT SYNTI-I" Sofiware Wavetable.
This PIug-and-Play sound card is comprised ofthe following functions:
3D sound effect and a Hardware Wavetahle Upgrade function which lets you add a
stereo audio to your personal computer system. Our add-in sound card provides an
integrated audio sub—syslem and is completelyjumper and swilch free,
1.1. Features
Single mixed-signal, high performance VLSI sound ASIC
Compatible with Sound Blaster, Sound Blaster Pro ‘ Sound Blaster 16
Emulation and Windows Sound System
Built-in 3D Sound Effect Processor
Built-in ALSFM Synthesizer w/ external wavetable support
ISA Plug-and—Play support logic
Supports Sound Blaster ADPCM decompression
MPU-401 MIDI controller with FIFO
Supports 8-bit Type F DMA lines (0, 1,3)
Software selectable intemipt lines (5, 7, 9, 10, 11)
8/16 bit mono/stereo digital audio from 4 kHz lo 48 kHz
Enhanced normal & digital game pon support
MIDI port with inpul and output FIFO
Full duplex for concurrent recording and playback
16-bit PNP address l/O decoder
510 V digital/analog mode
IOO-pin PQFP package
Applications
- Windows and MPC level 2 compatible audio sub-system
- PC games
- Computer vased audio reproduction
UU
UUUUUUUUUUUUUU
...
3°
Karoke/music sound box
Voice annotations or voice E-mail interface
1.3. System Requirements
' An 80386 / 80486 PC computer or higher,
or Pentium with a VGA card installed
0 5 MB of free hard disk space
6 An available 16-bit expansion slot
PM; «9 PM Sound Card
Card Figure
11 <7 srnnxour
u 4— unm
14.7 man
IIIIIIIIIIIIIIIIIH IIIIIIIIIIIIIIIIIIIlIIIIIIII ‘IIIIIIIIIIIr
mwun M CIA-mums" a...“
m nmrmvmus'n
1.5. Connectors
This Sound Card includes up to five internal Conneclors. three external Jack Ports, and
one exlemal MIDI/Joystick Connector.
1 5 1. Standard Connectors:
...¢3.5mm Phone Jack for SPEAKER OUT.
$3.5mm Phone Jack for LINE IN.
$3.5mm Phone Jack for MIC IN.
Connector for MlDl/JOYSTICK internal/enema].
J2:
J3:
J4:
1.5.2. Optional Connectors:
CN ' 26vpin Connector for WAVETABLE UPGRADE.
Jl Connector for [BB CD‘ROM AUDIOJN. (ATAPI)
Jl Connector for IDE CD-ROM AUDIO-IN. (JST)
J13:. ...Connec\or for VOICE MODEMI
Page - 4
P149 4? P144, Sound Card
1.5.3. Audio Connectors:
J10: IDE L:LEF1 OMANNEL SIGNAL
G: GROUND
R: RIGHT ENANNEL StGNAI.
LGGR
J11: IDE L: LEFTEHANNEL stem.
E. 0 O 0 o: GROUND
R: RIGHT CHANNEL SIGNAL
R G L G
J13: TAD Me: MONO our
3690 O E sienounn
41 Ml: mono IN
Mn G G Mi
2. HARDWARE INSTALLATION
2.1. Handling the Avance Logic ALSIZO Sound Card
WARNING: Static electricity can damage your equipment. Do not take the card
out of its static protective bag until you are ready to work with it.
Follow these precautions when handling the card:
c Before you open the static protective bag. touch it to a metal expansion slot cover
on the back of your computer. This drains static electricity from the package and
from your body.
0 Do not touch any exposed printed circuitry after opening the package.
Keep other people from touching the card. They might have a static~electricity
build~up.
- Limit your movement, Movement causes a build-up of static electricity
2.2. Installing the Avance Logic ALSIZO Sound Card
Step 1. Tum off the system and all peripheral devices.
Step 2. Disconnect the power cord and all peripheral devices from the
system,
Step 3. Remove the system cover and identify an unused 16—bit slot.
Step 4. Unscrew the slot cover plate, plug in the Sound Card and tighten it
with the screw.
Step 5. lfyou have speakers or amplifiers, plug the cable into the Audio Out
Jack on the back of the Sound Card.
5.9. - 5
PM if no, Sound Card
Step 6. Depending on what type ofCD Audio cable you have, connect J10 or
Jll on the Sound Card and the Audio output at the back of the CD-
ROM drive. Make sure pin 1 ON“) or Jll is connected to the
leflmost pin of the CD-ROM Audio output.
Step 7. Put back the system cover, reconnect the system power cord and all
peripheral devices. Check and make sure all connections are correct
before you turn on the system.
3. Software Installation
3.1. Software Contents
There is one installation diskette which is included in this package.
Applications r Diskette Name
Windows 3.l ALSIZO DOS/Windows 3.1/Windows 95 Drivers and Utilities
ALSIZO DOS/Windows 3.1/Windows 95 Drivers and Utilities
ALSIZO DOS/W' dows 3 /Windows 95 Drivers and Utilities
Windows NT 3.51/41) ALSlZD Windows NT 3.5 l/4.0 Drivers
3.2. Software Driver Installation under Windowso 3.1
1. Start up Microsofl® Windows® 3.1 operating system,
2. Insert the ALSl20 DOS/Windows 3.1/Windows 95 Drivers and Utilities diskette
into the floppy disk drive A or B.
3. Select the RUN item from the Program Manager File menu and type
A:\Win31_95\Setup into the command line.
4. A Welcome dialog box will appear, Click on the “Next” push button to continue the
installation.
5. A “Choose Destination Location“ dialog box will appear. Click on the “Next“ push
button in the “Choose Destination" dialog box to install the ALSIZO sound driver to
the default directory or click on the “Browse” push button if you want to install to a
different directory.
6, Setup will automatically create a folder and icons for the sound application.
7. A Modifying AUTOEXECBAT dialog box will appear. Click on the “Next" push
button to accept the default to “Let Setup modify the AUTOEXECBATfile”.
8. A Configuration Panel dialog box will appear during the first time installation.
Please check the hardware settings and make changes appropriate to the hardware
installation and in case you cannot hear sound during tests.
9, Click on the “Finish" push button. Setup will configure the hardware settings, Refer
to the Setup Utility Program in the next chapter to configure your sound card.
10. After the configuration in complete, remove the diskette from the diskette drive.
Page-6
Play & PM; Sound Card
3.3. Software Driver Installation Under DOS
. Afler installing the ALSlZO sound card, insert the “ALS 120 DOS/Windows
3.1/Windows 95 Drivers and Utilities“ installation diskette into your floppy disk
drive A or B.
lfWindows® 3il is currently running, exit the application.
At the C:\> prompt. type A or B and press the ENTER key. At the A:\Win31'95\>
prompt, type DOSINST EXE and press the ENTER key
The Avance Sound Chip Installation Program screen will be displayed showing the
following defaults.
Avance sofiware copy to: C:\A3SOUND
System bootup drive: C:\
- To make changes to the defaults, select the parameter with the UP/DOWN
Arrow keys and press the ENTER key. Then change the parameter and press the
ENTER key again to accept the change.
0 When satisfied with the new parameters or to accept the defaults, select “Accept
the above“ with the UP/DOWN Arrow keys and press the ENTER key.
The installation ofthe Avance Logic software drivers will now begin.
When all ofthe files are copied to the fixed disk, the installation program will
automatically update the AUTOEXECBAT file, saving copies ofthe original files
with the extension “ALS”, and the ABCONFIGEXE utility will automatically start.
Use the instructions given in the “SETUP Utility Program” on the next page to set
up the ALSIZO sound card.
When the installation and setup are complete, remove the diskette from the floppy
disk drive.
3.4. Software Driver Installation under Windows® 95
. Start up your Microsofi® Windows® 95 operating system.
The “New Hardware Found” dialog box will appear. Click on the OK push button
to accept the default Select “Driver from disk provided by hardware manufacturer".
. Click on the 0K push button when the “Install From Disk" dialog box appears.
Insert the “ALSlZO DOS/Windows 3 l/Windows 95 Drivers and Utilities” diskette
into your floppy disk drive A or B. Select the correct directory and click on the OK
push button Wmdows® 95 will automatically copy all the necessary files and
configure the ALSIZO sound card.
, The sound application is included on this diskette and you have the option of
installing it now, lfyou do not need to install the application, remove the diskette
from the floppy disk drive and skip procedure 5 to 10.
PM 4? PM, Sound Card
5. Select the RUN item from the START menu and the Run dialog box will appear.
m cm.
6. Type A:\Win3l_95\5etttp and click on the OK push button.
7 Click on “Next" in the Welcome dialog box.
8 A Choose Destination dialog box will appear Click on “Next“ to install the sound
driver to the default directory or click on the “Browse" push button if you want to
install to a different directory.
9. Windows will automatically create fl folder and icon for the sound application
IO. Click on “Finish" to complete the installation.
”Remove the diskette from your floppy disk drive.
3.5. Software Driver Installation Under
Windows® NT 3.51/40
l. Ensure that the ALSlZO sound card is installed properly and start up your
Microsofi® Windows® NT 3.51/4.0 operating system.
2. Insert the installation diskette, labeled “ALSlZO Windows NT Drivers and Utilities“
into your floppy disk drive A or B.
Go to the >Control Panel >Mulrimedia >Device >Add and choose OK for “Avance
Logic, lnc.Sound Chip’fl
3. While installing, the “Driver Exists" wanting message will appear and ask you
whether to keep the old “midimapefg” or . Please select ,
otherwise MIDI will not function properly
4, Configure the proper l/Os and DMAs if necessary as they appear on screen.
5, Re-boot the system and remove the driver diskette before the driver will take effect.
A-l 15-0054
Version 1.0
Page - 8
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2001:06:21 14:58:22 Producer : Acrobat Distiller 4.0 for Windows Author : VicodinES /CB /TNN Title : 44559.pdf Modify Date : 2001:06:21 14:58:29-04:00 Page Count : 9EXIF Metadata provided by EXIF.tools