Laird Connectivity 1004 Sterling-LWB5 User Manual
Laird Technologies Sterling-LWB5 Users Manual
Users Manual
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 1 of 25
Sterling-LWB5 Module
APPLICATION GUIDE
Last updated
May 24, 2017
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 2 of 25
Table of Contents
1 Introduction ............................................................................................................................ 3
1.1 Purpose & Scope ....................................................................................................................... 3
1.2 Applicable Documents ............................................................................................................... 3
2 Sterling-LWB5 Modules and Accessories .................................................................................. 4
3 Sterling-LWB5 Module PCB Layout Requirements .................................................................... 5
4 Reference Designs ................................................................................................................... 6
4.1 Chip Antenna ............................................................................................................................. 7
4.2 U.FL (External Antenna) ............................................................................................................ 9
5 Sterling-LWB5 Approved Antenna Specifications ................................................................... 11
5.1 External Antenna Connector ................................................................................................... 11
5.2 Chip Antenna Specifications .................................................................................................... 12
5.3 LSR 2.4/5.5 GHz Dual-Band FlexPIFA Antenna Specifications .............................................. 14
5.4 LSR 2.4/5.5 GHz Dual-Band Dipole Antenna Specifications .................................................. 16
6 EMC Compliance .................................................................................................................... 18
6.1 Summary ................................................................................................................................. 18
6.2 Module Integration Considerations - Antenna Systems .......................................................... 18
6.3 Module Integration Considerations - Substitute Antenna Systems ......................................... 18
6.4 Module Integration Considerations - Circuit Implementation .................................................. 19
6.5 Module Integration Considerations - Top Assembly................................................................ 19
6.6 Testing Requirements for End-Product ................................................................................... 19
6.7 Agency Certifications ............................................................................................................... 20
6.8 Agency Statements ................................................................................................................. 20
6.9 OEM Responsibilities To Comply With FCC and Industry Canada Regulations .................... 22
6.10 OEM Labeling Requirements For End-Product ....................................................................... 23
6.11 OEM End-Product User Manual Statements ........................................................................... 24
7 Contacting LSR ....................................................................................................................... 25
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 3 of 25
1 Introduction
1.1 Purpose & Scope
The purpose of this document is to provide details regarding the design and integration of
certified antennas to the Sterling-LWB5 module. It covers all three certified off module antenna
options, which consist of a ceramic chip, LSR dipole, and LSR FlexPIFA antenna. It will inform the
designer as to the required PCB details required to retain the LSR modular certification for the
Sterling-LWB5 module.
1.2 Applicable Documents
• Sterling-LWB5 Datasheet (330-0208)
• LSR 2.4/5.5 GHz Dipole Antenna Datasheet (330-0094)
• LSR U.FL to RPSMA Cable Datasheet (330-0018)
• LSR 2.4/5.5 GHz FlexPIFA Antenna Datasheet (330-0156)
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 4 of 25
2 Sterling-LWB5 Modules and Accessories
The Sterling-LWB5 Base Module is a System in Package (SIP) module. The Sterling-LWB5 module
is certified with several off module antennas.
Part Number
Description
LSR 450-0162
LSR 450-0162R
LSR 450-0162C
Sterling-LWB5 Module
Sterling-LWB5 Module, Tape & Reel
Sterling-LWB5 Module, Cut Tape
Johanson
2450AD14A5500T
2.4/5.5 GHz Chip Antenna
LSR 001-0016
2.4/5.5 GHz FlexPIFA Antenna w/U.FL cable,
100mm
001-0009
2.4/5.5 GHz Dipole Antenna with Reverse Polarity
SMA Connector
LSR 080-0001
U.FL to Reverse Polarity SMA Bulkhead Cable 105
mm
Table 1 Sterling-LWB5 Modules and Accessories
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 5 of 25
3 Sterling-LWB5 Module PCB Layout Requirements
Since the modules and their associated set of approved antennas has been certified by the FCC
and Industry Canada (IC) as a Modular Radio, the end user is authorized to integrate these
modules into an end-product, and is solely responsible for the Unintentional Emissions levels
produced by the end-product.
In order to preserve the Modular Radio certifications, the integrator of the module must abide
by the PCB layout recommendations outlined in the following paragraphs. Any divergence from
these recommendations will invalidate the modular radio certifications and require the
integrator to re-certify the module and/or end-product.
The module must be used with one of the approved antennas:
1. Johanson Technology 2450AD14A5500T Ceramic Chip Antenna.
2. LSR 001-0016 2.4/5.5 GHz FlexPIFA Antenna w/U.FL cable.
3. LSR 001-0009 center-fed 2.4/5.5 GHz dipole antenna and 080-0001 U.FL to Reverse Polarity
SMA connector cable.
When using the modules and or the reference designs that support the off module U.FL
connector(s), you may use a substitute antenna if the antenna gain is less than or equal to +2.5
dBi in the 2.4 GHz band and less than or equal to +4 dBi in the 5 GHz band. It may be possible to
use a substitute chip antenna, however there are restrictions so please contact LSR for guidance
prior to making any chip antenna substitutions.
LSR provides a FCC Modular Certified reference design. It is a controlled impedance PCB that
uses microstrip trace design to route RF signals from the Sterling-LWB5 module to the Antennas
and coaxial connectors.
Please use the latest CAD files from the LSR web site when incorporating the Sterling-LWB5
module into a new design. CAD files are provided in native Mentor Graphics PADS PCB and
PADS Logic formats, as well as ASCII, Gerber, and PDF formats. CAD files can also be translated
to most popular CAD package. Contact LSR Tech support for CAD translation.
Visit the LSR web site http://www.lsr.com for current PCB and Schematic CAD files.
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 6 of 25
4 Reference Designs
In order to use the modular certification for your design, it is critical that the reference design is
correctly followed. This section describes the details of using a PCB that is a 4-layer stack up.
The full 4-layer Chip Antenna PCB reference design is shown in Figure 1 and Bill of Materials in
Table 2. The full 4-layer U.FL (external antenna) PCB reference design is shown in Figure 2 and
Bill of Materials in Table 3.
It is not required to replicate the entire design, but what is required are the circuitry and layout
as it pertains to the antenna configuration being used in your design as shown in
Visit the LSR web site http://www.lsr.com for the current PCB and Schematic CAD files.
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 7 of 25
4.1 Chip Antenna
Figure 1 Chip Antenna Reference Design
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 8 of 25
Qty
PCB Ref
POP
Option
Value
Tolerance
Manufacturer
Mfg Part Number
1
ANT1
JOHANSON
2450AD14A5500#
1
!C1
1.3nH
+/- 0.1nH
Murata
LQP15MN1N3B02#
1
C3
4.7uF
+/- 20%
Murata
GRM155R60G475ME47#
1
C4
10pF
+/- 5%
Murata
GRM1555C1H100JA01#
2
C8 C9
NP
10pF
+/- 5%
Murata
GRM1555C1H100JA01#
1
C5
NP
1.0pF
+/- 0.25pF
Murata
GRM1555C1H1R0CA01#
1
C10
NP
10uF
+/- 10%
Murata
GRM188R61A106KE69#
1
D1
Infineon
ESD108B1CSP0201XTSA1
1
J1
NP
Hirose
U.FL-R-SMT-1#
1
L1
2.2uH
+/- 20%
TDK
MLP2016H2R2M#0S1
1
M1
LSR
450-0162
2
R1 R4
0
50m Ohm Max
KOA
RK73Z1ET#
1
R3
NP
0
50m Ohm Max
KOA
RK73Z1ET#
1
*R2
1.0pF
+/- 0.1pF
Murata
GJM1555C1H1R0BB01#
Notes:
# designates mfg material package option.
* Capacitor placed on Resistor footprint
! Inductor placed on Capacitor footprint
* RF Critical Components That Cannot be Substituted
Table 2 Chip Antenna Reference Design BOM
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 9 of 25
4.2 U.FL (External Antenna)
Figure 2 U.FL (External Antenna) Reference Design
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 10 of 25
Qty
PCB Ref
POP
Option
Value
Tolerance
Manufacturer
Mfg Part Number
1
ANT1
NP
JOHANSON
2450AD14A5500#
1
!C1
NP
1.3nH
+/- 0.1nH
Murata
LQP15MN1N3B02#
1
C3
4.7uF
+/- 20%
Murata
GRM155R60G475ME47#
1
C4
10pF
+/- 5%
Murata
GRM1555C1H100JA01#
2
C8 C9
NP
10pF
+/- 5%
Murata
GRM1555C1H100JA01#
1
C5
NP
1.0pF
+/- 0.25pF
Murata
GRM1555C1H1R0CA01#
1
C10
NP
10uF
+/- 10%
Murata
GRM188R61A106KE69#
1
D1
Infineon
ESD108B1CSP0201XTSA1
1
J1
Hirose
U.FL-R-SMT-1#
1
L1
2.2uH
+/- 20%
TDK
MLP2016H2R2M#0S1
1
M1
LSR
450-0162
2
R3 R4
0
50m Ohm Max
KOA
RK73Z1ET#
1
R1
NP
0
50m Ohm Max
KOA
RK73Z1ET#
1
*R2
NP
1.0pF
+/- 0.1pF
Murata
GJM1555C1H1R0BB01#
Notes:
# designates mfg material package option.
* Capacitor placed on Resistor footprint
! Inductor placed on Capacitor footprint
* RF Critical Components That Cannot be Substituted
Table 3 U.FL (External Antenna) Reference Design BOM
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 11 of 25
5 Sterling-LWB5 Approved Antenna Specifications
5.1 External Antenna Connector
Either the LSR 2.4/5.5 GHz Dual-Band Dipole Antenna with Reverse Polarity SMA Connector and U.FL to
SMA Cable or the LSR 2.4/5.5 GHz Dual-Band FlexPIFA Antenna are used in conjunction with the Hirose
PCB mounted U.FL connector to provide an externally mounted antenna solution for the Sterling-LWB5
module.
5.1.1 U.FL Connector Drawing
Figure 3 U.FL Connector Drawing
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 12 of 25
5.2 Chip Antenna Specifications
The Johanson 2450AD14A5500T Ceramic Chip Antenna provides an off-module, PCB mounted, antenna
solution for the Sterling-LWB5 module. The antenna on the Sterling-LWB5 evaluation platform is
positioned on the PCB to allow maximum performance while using a minimum amount of board space.
Figure 4 Chip Antenna Specifications
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 13 of 25
5.2.1 Chip Antenna Mechanical Dimensions
Figure 5 Chip Antenna Mechanical Dimensions
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 14 of 25
5.3 LSR 2.4/5.5 GHz Dual-Band FlexPIFA Antenna Specifications
The LSR 2.4/5.5 GHz Dual-Band FlexPIFA Antenna is used in conjunction with the Hirose PCB mounted
U.FL connector (Figure 3), to provide an externally mounted antenna solution for the Sterling-LWB5
module.
Specification
Value
2.4 GHz Band Peak Gain
+2.5 dBi
5 GHz Band Peak Gain
+3 dBi
2.4 GHz Average Gain
> -1.9 dBi
5 GHz Average Gain
> -4.0 dBi
Impedance
50 ohms
Type
Flexible Planar Inverted F Antenna (FlexPIFA)
Polarization
Linear
VSWR
<3.0:1, 2400 – 2480 MHz
<3.0:1, 4900 – 5900 MHz
Frequency
2400 - 2480 MHz, 4900 - 5900 MHz
Weight
1.13g
Size
38.6mm × 12.7mm × 2.5mm
Antenna Color
Clear Yellow
Adhesive
3M 100MP
Operating Temp
-40°C to +85°C
Connector Mating Height
U.FL: 2.5mm Max
Table 4 LSR 2.4/5.5 GHz Dual-Band FlexPIFA Antenna Specifications
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 15 of 25
5.3.1 LSR 2.4/5.5 GHz Dual-Band FlexPIFA Antenna Mechanical Dimensions
Figure 6 LSR 2.4/5.5 GHz Dual-Band FlexPIFA Antenna Mechanical Dimensions
Visit the LSR web site http://www.lsr.com for further information on the LSR Dual-Band FlexPIFA Antenna.
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 16 of 25
5.4 LSR 2.4/5.5 GHz Dual-Band Dipole Antenna Specifications
The LSR 2.4/5.5 GHz Dual-Band Dipole Antenna is used in conjunction with the LSR U.FL to Reverse
Polarity SMA Cable, and the Hirose PCB mounted U.FL connector (Figure 3), to provide an externally
mounted antenna solution for the Sterling-LWB5 module.
Specification
Value
2.4Ghz Band Peak Gain
+2 dBi
5 GHz Band Peak Gain
+2 dBi
Impedance
50 ohms, Nominal
Type
Dipole
Polarization
Linear Vertical
VSWR
≤2.0：1, Maximum
Frequency
2400-2500MHz, 5150-5850MHz
Weight
22g
Size
137 × 13 mm
Antenna Color
Black
Operating Temp
-20°C to +65°C
UL Rating
UL 94HB
Table 5 LSR 2.4/5.5 GHz Dual-Band Dipole Antenna Specifications
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 17 of 25
5.4.1 LSR 2.4/5.5 GHz Dual-Band Dipole Antenna Mechanical Dimensions
Figure 7 LSR 2.4/5.5 GHz Dual-Band Dipole Antenna Mechanical Dimensions
Visit the LSR web site http://www.lsr.com for further information on the LSR Dual-Band Dipole Antenna.
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 18 of 25
6 EMC Compliance
6.1 Summary
The Sterling-LWB5 module has been tested and approved as a Modular Radio in accordance with the
appropriate FCC and IC standards. The supporting test data may be found in the modular test report.
Since this module and its associated set of approved antennas have been certified as a Modular Radio,
this allows the end user to integrate this module into an end-product without the requirement of re-
certifying the radio module. The module-integrator is responsible for the unintentional conducted and
radiated emissions and must verify that the integrated product is compliant with the rules associated
with unintentional radiators. The module integrator is also required to maintain an engineering record
of the verification testing and declare on the product through proper labeling and marking that the
device is compliant with these particular rules.
The installed module’s FCC ID and IC numbers need to be clearly marked on the product with the
following verbiage “Contains FCC ID: TFB-1004” and "Contains IC: 5969A-1004".
6.2 Module Integration Considerations - Antenna Systems
The module must be used with one of the approved antennas:
1)
LSR 001-0009 2.4/5.5 GHz center-fed dipole antenna and LSR 080-0001 U.FL to Reverse Polarity SMA connector
cable.
2)
LSR 001-0016 2.4/5.5 GHz FlexPIFA antenna.
3)
Johanson 2450AD14A5500T chip antenna.
The antenna should be placed such that it is minimally disturbed by the product’s packaging material.
The incorporation of the largest practical free-space clearance around the antenna is important for
maximizing overall performance. Further, the antenna must be placed such that at least a 70 mm
separation distance is maintained from the antenna to all other radio transmitters.
6.3 Module Integration Considerations - Substitute Antenna Systems
The module’s certification is only valid for the list of approved antennas presented in section 6.2. When
using the U.FL connector, you may use a substitute antenna in place of an approved antenna, only if the
antennas are of the same type and the peak antenna gain is less than or equal to the peak gain of the
similar approved antenna. It may be possible to use a substitute chip antenna however there are
restrictions so please contact LSR for guidance prior to making any chip antenna substitutions.
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 19 of 25
6.4 Module Integration Considerations - Circuit Implementation
It is recommended that all connection PCB (printed circuit board) traces to the power supply and digital
control terminal be as short as possible. Though not necessarily required in all cases, it is a best practice
to provide an optional shunt capacitor placement at the module pin on all active and routed power
supply and digital control lines. Further, a series damping resistor placement should be incorporated
between the module pin/shunt capacitor node and the source/sink of the digital control signals. This
provides for effective bypassing and decoupling of digital lines from the radio module, in the event that
the application circuit has longer power supply and digital routing.
6.5 Module Integration Considerations - Top Assembly
In addition to the recommendations given for the antenna systems and the module placement onto a
product PCB, it is recommended that all wiring and interconnect systems within the product not be
routed anywhere close the module and its associated circuitry on the PCB, doing so could change the
emission characteristics of the module.
6.6 Testing Requirements for End-Product
Once the module is integrated and the end-product is realized, the end-product must be tested and
follow the verification process for Unintentional Conducted and Radiated Emissions in accordance to the
FCC and IC guidelines. The module needs to be powered and placed in the receive mode for this test.
The receiver must be tuned to its lowest frequency channel, mid-frequency channel, and highest
frequency channel. The supporting test data does not need to be submitted to the FCC or IC.
The implementation of the module in a specific end-product should also be reviewed to ensure
compliance with the FCC and IC requirements for SAR and MPE. Additional information for SAR
requirements of this module can be found in this document.
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 20 of 25
6.7 Agency Certifications
FCC ID: TFB-1004, 15.247
IC ID: 5969A-1004, RSS 247
CE: Compliant to standards EN 60950-1, EN 300 328, and EN 301 489
6.8 Agency Statements
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC CAUTION: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 21 of 25
Industry Canada Statements
This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful
communication.
This device has been designed to operate with the antenna(s) listed below, and having a maximum gain
of 2.0/2.0 dBi (LSR Dipole), 2.5/3.0 dBi (LSR FlexPIFA), and 1.0/4.0 dBi (Johanson Chip). Antennas not
included in this list or having a gain greater than 2.0/2.0 dBi, 2.5/3.0 dBi, and 1.0/4.0 5dBi are strictly
prohibited for use with this device. The required antenna impedance is 50 ohms.
List of all Antennas Acceptable for use with the Transmitter
1)
LSR 001-0009 center-fed 2.4 GHz and 5.5 GHz dipole antenna and LSR 080-0001 U.FL to Reverse Polarity SMA
connector cable.
2)
LSR 001-0016 2.4 GHz and 5.5 GHz FlexPIFA antenna.
3)
Johanson Technology 2450AD14A5500 chip antenna.
Cet appareil est conforme avec Industrie Canada , exempts de licence standard RSS (s). L'opération
est soumise aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences et (2)
cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de l'appareil.
Pour réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doiventêtre
choisis de manière que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pascelle permise
pour une communication réussie.
Cet appareil a été conçu pour fonctionner avec l'antenne (s) ci-dessous, et ayant un gain maximum de
2,0/2,0 dBi (LSR Dipole), 2,5/3,0 dBi (LSR FlexPIFA), et 1,0/4,0 dBi (Johanson Chip). Antennes pas inclus
dans cette liste ou présentant un gain supérieure à 2,0/2,0 dBi, 2,5/3,0 dBi, et 1,0/4,0 dBi sont
strictement interdits pour une utilisation avec cet appareil. L'impédance d'antenne requise est de 50
ohms.
Liste de toutes les antennes acceptables pour une utilisation avec l'émetteur
1)
Antenne LSR 001-0009 centre-alimenté 2,4 GHz et 5,5 GHz dipôle et LSR 080-0001 U.FL à Inverse câble
connecteur SMA à polarité.
2)
LSR 001-0016 2,4 GHZ et 5,5 GHz antenne FlexPIFA.
3)
Antenne de puce Johanson Technology 2450AD14A5500.
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 22 of 25
6.9 OEM Responsibilities To Comply With FCC and Industry Canada Regulations
The Sterling-LWB5 Module has been certified for integration into products only by OEM integrators
under the following conditions:
To comply with FCC and Industry Canada RF exposure limits for general population / uncontrolled
exposure, the antenna must be installed to provide a separation distance of at least 70 mm from all
persons and operating in conjunction with any other antenna or transmitter, except in accordancce with
FCC multi-transmitter product procedures.
As long as the two conditions above are met, further transmitter testing will not be required.
However, the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed (for example, digital device
emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations
or co-location with another transmitter), then the FCC and Industry Canada authorizations are
no longer considered valid and the FCC ID and IC Certification Number cannot be used on the
final product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC and Industry Canada
authorization.
Le module de Sterling-LWB5 a été certifié pour l'intégration dans des produits uniquement par des
intégrateurs OEM dans les conditions suivantes:
Pour se conformer aux limites d'exposition aux RF de la FCC et d'Industrie Canada pour la population
générale / exposition non contrôlée, l'antenne doit être installé pour fournir une distance de séparation
d'au moins 70 mm de toutes les personnes et fonctionnant conjointement avec une autre antenne ou
émetteur, sauf en conformité avec la FCC procédures de produits multi- émetteurs.
Tant que les deux conditions précitées sont réunies, les tests de transmetteurs supplémentaires ne
seront pas tenus. Toutefois, l'intégrateur OEM est toujours responsable de tester leur produit final pour
toutes les exigences de conformité supplémentaires requis avec ce module installé (par exemple, les
émissions appareil numérique, les exigences de périphériques PC, etc.)
NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (pour certaines
configurations ou de co-implantation avec un autre émetteur), puis la FCC et Industrie
autorisations Canada ne sont plus considérés comme valides et l'ID de la FCC et IC numéro de
certification ne peut pas être utilisé sur la produit final. Dans ces circonstances, l'intégrateur
OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'un distincte
de la FCC et Industrie Canada l'autorisation.
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 23 of 25
6.10 OEM Labeling Requirements For End-Product
The Sterling-LWB5 module is labeled with its own FCC ID and IC Certification Number. The FCC ID and IC
certification numbers are not visible when the module is installed inside another device, as such the end
device into which the module is installed must display a label referring to the enclosed module. The
final end product must be labeled in a visible area with the following:
“Contains Transmitter Module FCC ID: TFB-1004”
“Contains Transmitter Module IC: 5969A-1004”
or
“Contains FCC ID: TFB-1004”
“Contains IC: 5969A-1004”
The OEM of the Sterling-LWB5 Module must only use the approved antenna(s) listed above, which have
been certified with this module.
Le module de Sterling-LWB5 est étiqueté avec son propre ID de la FCC et IC numéro de
certification. L'ID de la FCC et IC numéros de certification ne sont pas visibles lorsque le module
est installé à l'intérieur d'un autre appareil, comme par exemple le terminal dans lequel le module est
installé doit afficher une etiquette faisant référence au module ci-joint. Le produit final doit être
étiqueté dans un endroit visible par le suivant:
“Contient Module émetteur FCC ID: TFB-1004"
“Contient Module émetteur IC: 5969A-1004"
ou
“Contient FCC ID: TFB-1004"
“Contient IC: 5969A-1004"
Les OEM du module Sterling-LWB5 ne doit utiliser l'antenne approuvée (s) ci-dessus, qui ont été
certifiés avec ce module.
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 24 of 25
6.11 OEM End-Product User Manual Statements
The OEM integrator should not to provide information to the end user regarding how to install or
remove this RF module or change RF related parameters in the user manual of the end product.
The user manual for the end product must include the following information in a prominent location:
To comply with FCC and Industry Canada RF exposure limits for general population / uncontrolled
exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 70 mm from all persons and operating in conjunction with any other antenna or transmitter,
except in accordance with FCC multi-transmitter product procedures.
Other user manual statements may apply.
L'intégrateur OEM ne devraient pas fournir des informations à l'utilisateur final sur la façon d'installer ou
de supprimer ce module RF ou modifier les paramètres liés RF dans le manuel utilisateur du produit
final.
Le manuel d'utilisation pour le produit final doit comporter les informations suivantes dans unendroit
bien en vue:
Pour se conformer aux limites d'exposition aux RF de la FCC et d'Industrie Canada pour la population
générale / exposition non contrôlée, l'antenne(s) utilisée pour ce transmetteur doit être installé pour
fournir une distance de séparation d'au moins 70 mm de toutes les personnes et fonctionnant
conjointement avec une autre antenne ou émetteur, sauf en conformité avec les procédures de produits
multi- émetteur FCC.
Autres déclarations manuel de l'utilisateur peuvent s'appliquer.
Sterling-LWB5 Module
APPLICATION GUIDE
The information in this document is subject to change without notice.
Sterling-LWB5 User Manual Copyright © 2016-2017 LSR Page 25 of 25
7 Contacting LSR
Headquarters LS Research, LLC
W66 N220 Commerce Court
Cedarburg, WI 53012-2636
USA
Tel: (262) 375-4400
Fax: (262) 375-4248
Website www.lsr.com
Technical Support forum.lsr.com
Sales Contact sales@lsr.com
The information in this document is provided in connection with LS Research (hereafter referred to as “LSR”) products. No
license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in
connection with the sale of LSR products. EXCEPT AS SET FORTH IN LSR’S TERMS AND CONDITIONS OF SALE LOCATED ON
LSR’S WEB SITE, LSR ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL LSR BE LIABLE FOR ANY DIRECT,
INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES
FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE
THIS DOCUMENT, EVEN IF LSR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. LSR makes no representations or
warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make
changes to specifications and product descriptions at any time without notice. LSR does not make any commitment to update
the information contained herein. Unless specifically provided otherwise, LSR products are not suitable for, and shall not be
used in, automotive applications. LSR’s products are not intended, authorized, or warranted for use as components in
applications intended to support or sustain life.