Laird Connectivity BT2 TiWi-uB1 User Manual

LS Research, LLC TiWi-uB1

User Manual

TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 1 of 22 TiWi-uB1 Bluetooth Smart (BLE) Module  FEATURES   Built  in  CC2541  single-chip  Bluetooth Smart  (BLE  4.0)  System-On-Chip (SOC).   RF Output Power: 0 dBm (Class 3)   RF Receive Sensitivity: -92 dBm   Size: 11.6mm x 17.9 mm x 2.3 mm   Operating Voltage: 2.0V to 3.6V   Operating Temperature: -40 to +85o C   Worldwide Acceptance:  FCC  (USA),  IC (Canada), and CE (Europe)   REACH and RoHS compliant   Complete  power-optimized  stack, including Controller and Host o GAP  –  Central,  Peripheral, Observer,  or  Broadcaster  (Including Combination Roles) o ATT/GATT – Client and Server o SMP  – AES-128  Encryption  and Decryption o L2CAP   Multiple Configuration Options o Single-Chip  Configuration,  Allowing Applications to Run on CC2541 o Network  Processor  Interface  for Applications Running on an External Microcontroller  APPLICATIONS   2.4 GHz Bluetooth Low Energy Systems   Human-Interface  Devices  (Keyboard, Mouse, Remote Control)   Sports and Leisure Equipment   Mobile Phone Accessories   Consumer Electronics   DESCRIPTION LSR would like to announce a low-cost and low-power consumption module which has all of the BluetoothSmart functionalities.  The TiWi-uB1 module fully supports the  single mode Bluetooth Low Energy operation, and the output power can support class 3. The module provides  the  ability  to  either  put  your  entire application  into  the  integrated  8051 microcontroller,  or  use  the  module  in  Network Processor  mode  in  conjunction  with  the microcontroller of your choice. Need to get to market quickly?  Not an expert in Bluetooth Low Energy?  Need a custom antenna?  Do you need help with your host board?  LS Research Design Services will be happy to develop custom hardware or software, or help integrate the design.  Contact us at sales@lsr.com or call us at 262-375-4400.
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 2 of 22 TABLE OF CONTENTS FEATURES .......................................................................................................................... 1 APPLICATIONS ................................................................................................................... 1 DESCRIPTION ..................................................................................................................... 1 FOOTPRINT AND PIN DEFINITIONS.................................................................................. 4 PIN DESCRIPTIONS ............................................................................................................ 5 ELECTRICAL SPECIFICATIONS ........................................................................................ 6 Absolute Maximum Ratings ....................................................................................................................... 6 Recommended Operating Conditions ...................................................................................................... 6 General Characteristics .............................................................................................................................. 6 General Specifications ............................................................................................................................... 7 DC Characteristics ...................................................................................................................................... 7 Current Consumption ................................................................................................................................. 8 CURRENT CONSUMPTION WITH DC to DC Converter ........................................................................... 8 RF Characteristics ...................................................................................................................................... 9 SLOW CLOCK (32 KHZ) SOURCE REQUIREMENTS ..................................................... 10 32.768-kHz EXTERNAL CRYSTAL OSCILLATOR................................................................................... 10 32-kHz INTERNAL RC OSCILLATOR ....................................................................................................... 11 SPI INTERFACE CHARACTERISTICS ............................................................................. 12 DEBUG INTERFACE CHARACTERISTICS ...................................................................... 14 AGENCY CERTIFICATIONS ............................................................................................. 16 AGENCY STATEMENTS ................................................................................................... 16 Federal Communication Commission Interference Statement ............................................................ 16 Industry Canada Statements.................................................................................................................... 17 OEM RESPONSIBILITIES TO COMPLY WITH FCC AND INDUSTRY CANADA REGULATIONS ....................................................................................................... 18 OEM LABELING REQUIREMENTS FOR END-PRODUCT .............................................. 19 OEM END PRODUCT USER MANUAL STATEMENTS.................................................... 20 EUROPE ............................................................................................................................ 21 CE Notice ................................................................................................................................................... 21
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 3 of 22 Declaration of Conformity (DOC) ............................................................................................................ 21 BLUETOOTH CERTIFICATION ......................................................................................... 21 CONTACTING LS RESEARCH ......................................................................................... 22
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 4 of 22 FOOTPRINT AND PIN DEFINITIONS                                                       1          33   2          32   3          31   4          30   5          29   6          28   7          27   8          26   9          25   10          24   11          23   12          22    13 14 15 16 17 18 19 20 21                Figure 1 TiWi-uB1 Module Footprint (Viewed From Top)
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 5 of 22 PIN DESCRIPTIONS Module Pin Name I/O Type Description  1 RF OUT RF ANTENNA, 50 OHMS 2 GND GND GROUND 3 GND GND GROUND 4 OSC32K_Q1/P2_4 AI/DIO GENERAL PURPOSE DIGITAL I/O 5 OSC32K_Q2/P2_3 AI/DIO  32KHZ GENERAL PURPOSE DIGITAL I/O 6 /RESET DI ACTIVE LOW RESET 7 DC/P2_2 DI/DIO DEBUG CLOCK, GENERAL PURPOSE DIGITAL I/O 8 DD/P2_1 DIO DEBUG DATA, GENERAL PURPOSE DIGITAL I/O 9 NC - NO CONNECT (DO NOT CONNECT) 10 NC - NO CONNECT (DO NOT CONNECT) 11 AVCC PI ANALOG POWER SUPPLY TO MODULE (2.0V – 3.6V) 12 DVCC PI DIGITAL POWER TO SUPPLY MODULE (2.0V – 3.6V) 13 P2_0 DIO GENERAL PURPOSE DIGITAL I/O 14 SCL DIO I2C CLOCK, GENERAL PURPOSE DIGITAL I/O 15 SDA DIO I2C DATA, GENERAL PURPOSE DIGITAL I/O 16 P1_7 DIO GENERAL PURPOSE DIGITAL I/O 17 P1_6 DIO GENERAL PURPOSE DIGITAL I/O 18 P1_5 DIO GENERAL PURPOSE DIGITAL I/O 19 P1_4 DIO GENERAL PURPOSE DIGITAL I/O 20 P1_3 DIO GENERAL PURPOSE DIGITAL I/O 21 P1_2 DIO GENERAL PURPOSE DIGITAL I/O 22 GND GND GROUND 23 P1_1 DIO GENERAL PURPOSE DIGITAL I/O 24 P1_0 DIO GENERAL PURPOSE DIGITAL I/O 25 P0_7 DIO GENERAL PURPOSE DIGITAL I/O, ANALOG INPUT 26 P0_6 DIO GENERAL PURPOSE DIGITAL I/O, ANALOG INPUT 27 P0_5 DIO GENERAL PURPOSE DIGITAL I/O, ANALOG INPUT 28 P0_4 DIO GENERAL PURPOSE DIGITAL I/O, ANALOG INPUT 29 P0_3 DIO GENERAL PURPOSE DIGITAL I/O, ANALOG INPUT 30 P0_2 DIO GENERAL PURPOSE DIGITAL I/O, ANALOG INPUT 31 P0_1 DIO GENERAL PURPOSE DIGITAL I/O, ANALOG INPUT 32 P0_0 DIO GENERAL PURPOSE DIGITAL I/O, ANALOG INPUT 33 GND GND GROUND PI = Power Input    GND = Ground     DI = Digital Input     DO = Digital Output     DIO = Digital Input/Output AI = Analog Input     RF = Bi-directional RF Port Note: See the Texas Instruments CC2541 datasheet and user guide for further details on the I/O. Table 1 TiWi-uB1 Pin Descriptions
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 6 of 22 ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings Symbol Description Min Max Unit DVCC Digital Input Supply Voltage -0.3 3.9 V AVCC Analog Input Supply Voltage -0.3 3.9 V VDIO Voltage on any digital pin -0.3 VDD + 0.3 ≤ 3.9 V Table 2 Absolute Maximum Ratings1  Recommended Operating Conditions Test conditions: Ambient Temp = 25°C Symbol Min Typ Max Unit VCC 2.0 3.3 3.6 V Table 3 Recommended Operating Conditions   General Characteristics Characteristic Description Model Name TiWi-uB1 Product Description Bluetooth Low Energy Wireless Module Dimension 11.6 mm x 17.9 mm x 2.3 mm (W*L*T)  Operating temperature -40°C to 85°C Storage temperature -40°C to 85°C Humidity Operating Humidity 10% to 95% Non-Condensing Storage Humidity 5% to 95% Non-Condensing Weight 0.18 g  +/- 0.01g Table 4 General Characteristics    1 Under no circumstances should exceeding the ratings specified in the Absolute Maximum Ratings section be allowed.  Stressing the module beyond these limits may result permanent damage to the module that is not covered by the warranty.
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 7 of 22 General Specifications Measured on LSR TiWi-uB1 EM reference design with TA = 25°C and VDD = 3 V Parameter Test Conditions Min Typ Max Unit WAKE-UP AND TIMING Power mode 1 → Active Digital regulator on, 16-MHz RCOSC and 32-MHz crystal oscillator off. Start-up of 16-MHz RCOSC 4   µS Power mode 2 or 3 → Active Digital regulator off, 16-MHz RCOSC and 32-MHz crystal oscillator off. Start-up of regulator and 16-MHz RCOSC 120   µS Active → TX or RX Crystal ESR = 16 Ω. Initially running on 16-MHz RCOSC, with 32-MHz XOSC OFF 500   µS With 32-MHz XOSC initially on 180   µS RX/TX turnaround Proprietary auto mode 130   µS BLE mode 150   Data rate and modulation format 2 Mbps, GFSK, 500-kHz deviation 2 Mbps, GFSK, 320-kHz deviation 1 Mbps, GFSK, 250-kHz deviation 1 Mbps, GFSK, 160-kHz deviation 500 kbps, MSK (Proprietary RF Only) 250 kbps, GFSK, 160-kHz deviation 250 kbps, MSK (Proprietary RF Only) Table 5 Bluetooth General Specifications DC Characteristics Parameter Test Conditions Min Typ Max Unit Logic-0 input voltage    0.5 V Logic-1 input voltage  2.4   V Logic-0 input current Input equals 0 V -50  50 nA Logic-1 input current Input equals VDD -50  50 nA I/O-pin pullup/pulldown resistors   20  kΩ Logic-0 output voltage, 4- mA pins Output load 4 mA   0.5 V Logic-1 output voltage, 4-mA pins Output load 4 mA  2.5  V Logic-0 output voltage, 20- mA pins Output load 20 mA   0.5 V Logic-1 output voltage, 20-mA pins Output load 20 mA  2.5  V Table 6 Bluetooth General DC Characteristics
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 8 of 22 Current Consumption  Measured on LSR TiWiuB1 EM reference design with TA = 25°C, VDD = 3 V, fc = 2440 MHz. LEDs disabled, DC to DC disabled  Mode Description Average Current Unit Icore Core current consumption RX mode, standard mode, no peripherals active, low MCU activity 17.9 mA RX mode, high-gain mode, no peripherals active, low MCU activity 20.2 TX mode, –20 dBm output power, no peripherals active, low MCU activity 16.8 TX mode, 0 dBm output power, no peripherals active, low MCU activity 18.2 Power mode 1. Digital regulator on; 16-MHz RCOSC and 32-MHz crystal oscillator off; 32.768-kHz XOSC, POR, BOD and sleep timer active; RAM and register retention 270 µA Power mode 2. Digital regulator off; 16-MHz RCOSC and 32-MHz crystal oscillator off; 32.768-kHz XOSC, POR, and sleep timer active; RAM and register retention 1 Power mode 3. Digital regulator off; no clocks; POR active; 0.5 RAM and register retention 0.5 Low MCU activity: 32-MHz XOSC running. No radio or peripherals. Limited flash access, no RAM access. 6.7 mA I peri Peripheral current consumption  *Adds to core current Icore for each peripheral unit activated Timer 1. Timer running, 32-MHz XOSC used 90 µA Timer 2. Timer running, 32-MHz XOSC used 90 Timer 3. Timer running, 32-MHz XOSC used 60 Timer 4. Timer running, 32-MHz XOSC used 70 Sleep timer, including 32.753-kHz RCOSC 0.6  ADC, when converting 1.2 mA Table 7 Bluetooth General DC Characteristics CURRENT CONSUMPTION WITH DC to DC Converter Measured on LSR TiWiuB1 EM reference design with TA = 25°C, VDD = 3 V, fc = 2440 MHz. LEDs disabled, DC to DC Enabled 1 Mbsp, GFSK, 250-kHz deviation, Bluetooth™ low energy Mode, 1% BER Mode Description Average Current Unit Current consumption RX mode, standard mode, no peripherals active, low MCU activity 14.7 mA RX mode, high-gain mode, no peripherals active, low MCU activity 16.7 TX mode, –20 dBm output power, no peripherals active, low MCU activity 13.1 TX mode, 0 dBm output power, no peripherals active, low MCU activity 14.3 Table 8 Bluetooth Power Consumption
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 9 of 22 RF Characteristics Measured on LSR TiWiuB1 EM reference design with TA = 25°C, VDD = 3 V, fc = 2440 MHz. LEDs disabled, DC to DC disabled,  measured at RF connecter.  Parameter Test Conditions Min Typ Max Unit TRANSMIT SECTION Output Power Measured on LSR TiWiuB1 450-0106 EM reference design at RF connector using maximum recommended output power setting  0  dBm Measured on LSR TiWiuB1 450-0106 EM reference design at RF connector using minimum recommended output power setting  -20  Spurious emission conducted measurement f < 1 GHz  -52  dBm f > 1 GHz  -48  dBm RF frequency range Programmable in 1-MHz steps 2379                       2496 MHz RECEIVE SECTION  Receiver sensitivity(1) (2) 1 Mbps, GFSK, 250-kHz Deviation, Bluetooth low energy Mode, 0.1% BER  -94  dBm Saturation(2) BER < 0.1%  5  dBm Co-channel rejection (2) Wanted signal –67 dBm  -6  dB Frequency error tolerance Including both initial tolerance and drift. Sensitivity better than -67dBm, 250 byte payload. BER 0.1% -250                          250 KHz Intermodulation (2) Minimum interferer level  -36  dBm Table 9 Bluetooth RF Characteristics  1.  The receiver sensitivity setting is programmable using a TI BLE stack vendor-specific API command. The default value is standard mode. 2.  Results based on standard-gain mode.
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 10 of 22 SLOW CLOCK (32 KHZ) SOURCE REQUIREMENTS Two 32-kHz oscillators are available in the device as clock sources for the 32-kHz clock: • 32-kHz XOSC – External Crystal Oscillator • 32-kHz RCOSC – Internal RC Oscillator  By default, after a reset, the 32-kHz RCOSC is enabled and selected as the 32-kHz clock source. The RCOSC consumes less power, but is less accurate compared to the 32-kHz XOSC. The chosen 32-kHz clock source drives the Sleep Timer, generates the tick for the Watchdog Timer, and is used as a strobe in Timer 2 to calculate the Sleep Timer sleep time.  The crystal is required for accurate sleep timing, so it is only needed to for the module be BLE certified when using low power modes.  32.768-kHz EXTERNAL CRYSTAL OSCILLATOR Characteristic Condition Min         Typ Max Unit Crystal frequency   32768  Hz Crystal frequency accuracy requirement  -40  40 ppm ESR Equivalent series Resistance  6  60 Ω C0 Crystal shunt Capacitance  1  7 pF CL Crystal load capacitance  10  16 pF Start-up time   0.25  mS Power-down guard time The crystal oscillator must be in power down for a guard time before it is used again. This requirement is valid for all modes of operation. The need for power-down guard time can vary with crystal type and load.  3  mS Table 10 32 kHz External Clock Requirements
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 11 of 22 32-kHz INTERNAL RC OSCILLATOR Characteristic Condition Min Typ Max Unit Calibrated frequency (1)   32768  Hz Frequency accuracy after calibration  -40  40 ppm Temperature coefficient(2)   ±0.2  % Supply-voltage coefficient   3  %/V Calibration time(3)   2  mS Table 11 32 kHz Internal Clock Requirements 1) The calibrated 32-kHz RC oscillator frequency is 32-MHz divided by 977 2) Frequency drift when temperature changes after calibration 3) When the 32-kHz RC oscillator is enabled, it is calibrated when a switch from the 16-MHz RC oscillator to the 32-MHz crystal oscillator is performed while SLEEPCMD.OSC32K_CALDIS is set to 0.
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 12 of 22 SPI INTERFACE CHARACTERISTICS TA = –40°C to 85°C, VDD = 2 V to 3.6 V Characteristic Condition Min Typ Max Unit t1   SCK period Master, RX and TX 250   nS Slave, RX and TX 250   SCK duty cycle Master  50%   t2  SSN low to SCK Master 63   nS Slave 63   t3  SCK to SSN high Master 63   nS Slave 63   T4  SCK to SSN high Master, load = 10 pF   7 nS t5  MOSI late out Master, load = 10 pF   10 nS t6  MISO setup Master    nS t7  MISO hold Master    nS SCK duty cycle Slave  50%   t10 MOSI setup Slave    nS t11 MOSI hold Slave    nS t9 MISO late out Slave, load = 10 pF    nS Operating frequency Master, TX only   8 MHz Master, RX and TX   4 Slave, RX only   8 Slave, RX and TX   4 Table 12 SPI Timing
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 13 of 22  Figure 2 SPI Master Timing    Figure 3 Slave Timing
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 14 of 22 DEBUG INTERFACE CHARACTERISTICS  TA = –40°C to 85°C, VDD = 2 V to 3.6 V Characteristic Condition Min Typ Max Unit fclk_ dbg Debug clock frequency (see Figure 5)    12 MHz t1  Allowed high pulse on clock (see Figure 5)  35   ns t2 Allowed low pulse on clock (see Figure 5)  35   ns t  3  EXT_RESET_N low  to  first  falling  edge  on  debug  clock  (see  Figure 7)  167   ns t4 Falling edge on clock to EXT_RESET_N high (see Figure 7)  83   ns t6EXT_RESET_N high to first debug command (see Figure 7)  83   ns t6 Debug data setup (see Figure 6)  2   ns t7 Debug data hold (see Figure 6)  4   ns t8 Clock-to-data delay (see Figure 6) Load = 10 pF    ns Table 13  Debug Interface Timing   Figure 4 Slave Timing
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 15 of 22   Figure 5 Slave Timing    Figure 6 Slave Timing
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 16 of 22 AGENCY CERTIFICATIONS FCC ID: TFB-BT2, 15.247 IC ID: 5969A-BT2, RSS 210 CE: Compliant to standards EN 60950-1, EN 300 328, and EN 301 489   AGENCY STATEMENTS Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:   Reorient or relocate the receiving antenna.   Increase the separation between the equipment and receiver.   Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.   Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This portable transmitter with its antenna complies with FCC/IC RF exposure limits for general population / uncontrolled exposure. FCC  CAUTION:  Any  changes  or  modifications  not  expressly  approved  by  the  party responsible for compliance could void the user's authority to operate this equipment.
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 17 of 22 Industry Canada Statements This device complies with Industry Canada License-exempt RSS standard(s).  Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device has been designed to operate with the antenna(s) listed below, and having a maximum gain of -4.2 dBi (PCB Trace) and 2.0dBi (LSR 2.4 GHz Dipole).  Antennas not included in this list or having a gain greater than -4.2 dBi and 2.0 dBi are strictly prohibited for use with this device.  The required antenna impedance is 50 ohms. List of all Antennas Acceptable for use with the Transmitter  1)  On module PCB trace antenna.  2)  LS Research 001-0001 center-fed 2.4 GHz dipole antenna and LS Research 080-0001 U.FL to Reverse Polarity SMA connector cable.  Cet appareil est conforme aux normes d'Industrie Canada exempts de licence RSS (s).  L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. Pour réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doiventêtre choisis de manière que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pascelle permise pour une communication réussie. Cet appareil a été conçu pour fonctionner avec l'antenne (s) ci-dessous, et ayant un gain maximum de -4,2 dBi (PCB Trace) et 2,0 dBi (LSR 2.4 GHz Dipole). Antennes pas inclus dans cette liste ou présentant un gain supérieur à -4,2 dBi et 2,0 dBi sont strictement interdits pour une utilisation avec cet appareil. L'impédance d'antenne requise est de 50 ohms. Liste de toutes les antennes acceptables pour une utilisation avec l'émetteur 1)  Le module d'antenne PCB trace. 2)  LS Research 001-0001 centre-fed 2,4 GHz antenne dipôle et LS Research 080-0001 U.FL pour inverser câble connecteur SMA à polarité.
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 18 of 22 OEM RESPONSIBILITIES TO COMPLY WITH FCC AND INDUSTRY CANADA REGULATIONS The TiWi-uB1 Module has been certified for integration into products only by OEM integrators under the following conditions: The antennas for this transmitter must not be co-located with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter procedures.  Co-location means having a separation distance of less than 20 cm between transmitting antennas. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT  NOTE:  In  the  event  that  these  conditions  cannot  be  met  (for  certain configurations  or  co-location  with  another  transmitter),  then  the  FCC  and  Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will  be  responsible  for  re-evaluating  the  end  product  (including  the  transmitter)  and obtaining a separate FCC and Industry Canada authorization. Le module de TiWi-uB1 a été certifié pour l'intégration dans des produits uniquement par des intégrateurs OEM dans les conditions suivantes: Les antennes pour ce transmetteur ne doit pas être co-localisés avec les autres émetteurs sauf en conformité avec la FCC et Industrie Canada multi-émetteur procédures.  Co-localisation des moyens ayant une distance de séparation inférieure à 20 cm entre les antennes d'émission. Tant que les deux conditions précitées sont réunies, les tests de transmetteurs supplémentaires ne seront pas tenus. Toutefois, l'intégrateur OEM est toujours responsable de tester leur produit final pour toutes les exigences de conformité supplémentaires requis avec ce module installé (par exemple, les émissions appareil numérique, les exigences de périphériques PC, etc.) NOTE  IMPORTANTE:  Dans  le  cas  où  ces  conditions  ne  peuvent  être  satisfaites  (pour certaines configurations ou de co-implantation avec un autre émetteur), puis la FCC et Industrie autorisations Canada ne sont plus considérés comme valides et l'ID de la FCC et  IC  numéro  de  certification  ne  peut  pas  être  utilisé  sur  la  produit  final.  Dans  ces circonstances,  l'intégrateur  OEM  sera  chargé  de  réévaluer  le  produit  final  (y  compris l'émetteur) et l'obtention d'un distincte de la FCC et Industrie Canada l'autorisation.
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 19 of 22 OEM LABELING REQUIREMENTS FOR END-PRODUCT The TiWi-uB1 module is labeled with its own FCC ID and IC Certification Number.  The FCC ID and IC certification numbers are not visible when the module is installed inside another device, as such the end device into which the module is installed must display a label referring to the enclosed module.  The final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: TFB-BT2” “Contains Transmitter Module IC: 5969A-BT2” or “Contains FCC ID: TFB-BT2” “Contains IC: 5969A-BT2” The OEM of the TiWi-uB1 Module must only use the approved antenna(s) listed above, which have been certified with this module.  Le module de TiWi-uB1 est étiqueté avec son propre ID de la FCC et IC numéro de certification. L'ID de la FCC et IC numéros de certification ne sont pas visibles lorsque le module est installé à l'intérieur d'un autre appareil, comme par exemple le terminal dans lequel le module est installé doit afficher une etiquette faisant référence au module ci-joint. Le produit final doit être étiqueté dans un endroit visible par le suivant:  “Contient Module émetteur FCC ID: TFB-BT2" “Contient Module émetteur IC: 5969A-BT2"  ou  “Contient FCC ID: TFB-BT2" “Contient IC: 5969A-BT2"  Les OEM du module TiWi-uB1 ne doit utiliser l'antenne approuvée (s) ci-dessus, qui ont été certifiés avec ce module.
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 20 of 22 OEM END PRODUCT USER MANUAL STATEMENTS The OEM integrator should not provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. Other user manual statements may apply.  L'intégrateur OEM ne devraient pas fournir des informations à l'utilisateur final sur la façon d'installer ou de supprimer ce module RF ou modifier les paramètres liés RF dans le manuel utilisateur du produit final.  Autres déclarations manuel de l'utilisateur peuvent s'appliquer.
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 21 of 22 EUROPE CE Notice This device has been tested and certified for use in the European Union.  See the Declaration of Conformity (DOC) for specifics. If this device is used in a product, the OEM has responsibility to verify compliance of the final product to the EU standards.  A Declaration of Conformity must be issued and kept on file as described in the Radio and Telecommunications Terminal Equipment (R&TTE) Directive.  The ‘CE’ mark must be placed on the OEM product per the labeling requirements of the Directive. Declaration of Conformity (DOC) The DOC can be downloaded from the LSR Wiki.     BLUETOOTH CERTIFICATION The TiWi-uB1 module has been certified as a Controller Subsystem and has a QDID of B021230.
TiWi-uB1 Module DATASHEET  The information in this document is subject to change without notice.  330-0132  Copyright © 2013 LS Research, LLC  Page 22 of 22 CONTACTING LS RESEARCH Headquarters  LS Research, LLC   W66 N220 Commerce Court   Cedarburg, WI 53012-2636  USA   Tel: 1(262) 375-4400   Fax: 1(262) 375-4248 Website www.lsr.com Wiki www.lsr.com/products-wiki Technical Support www.lsr.com/products-forum Sales Contact sales@lsr.com                    The  information  in  this  document  is  provided  in  connection  with  LS  Research  (hereafter  referred  to  as  “LSR”) products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of LSR products. EXCEPT AS SET FORTH IN LSR’S TERMS AND CONDITIONS OF SALE LOCATED ON LSR’S WEB SITE, LSR ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS  ANY  EXPRESS,  IMPLIED  OR  STATUTORY  WARRANTY  RELATING  TO  ITS  PRODUCTS INCLUDING,  BUT  NOT  LIMITED  TO, THE  IMPLIED WARRANTY OF  MERCHANTABILITY, FITNESS  FOR  A PARTICULAR  PURPOSE,  OR  NON-INFRINGEMENT.  IN  NO  EVENT  SHALL  LSR  BE  LIABLE  FOR  ANY DIRECT,  INDIRECT,  CONSEQUENTIAL,  PUNITIVE,  SPECIAL  OR  INCIDENTAL  DAMAGES  (INCLUDING, WITHOUT  LIMITATION,  DAMAGES  FOR  LOSS  OF  PROFITS,  BUSINESS  INTERRUPTION,  OR  LOSS  OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF LSR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. LSR makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications  and  product  descriptions at  any time  without  notice.  LSR  does  not  make  any commitment  to update the information contained herein. Unless specifically provided otherwise, LSR products are not suitable for, and shall not be used in, automotive applications. LSR’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

Navigation menu