Laird Connectivity RM02410 2.4 GHz Frequency Hopping Spread Spectrum Transceiver System User Manual 1

AeroComm Corporation 2.4 GHz Frequency Hopping Spread Spectrum Transceiver System 1

Users Manual

RM024-10 Compliance Section
RM024 FCC / IC Information
Agency Identification Numbers
Family
US/FCC
CANADA/IC
RM024-10
KQL-RM02410
2268C-RM02410
RM024 FAMILY
*PART #
FORM FACTOR
TX OUTPUT
ANTENNA
RM024-S125-C-XX
Surface Mount
125mW
U.FL
RM024-S125-M-XX
Surface Mount
125mW
U.FL or chip
RM024-P125-C-XX
Pluggable
125mW
U.FL
RM024-P125-M-XX
Pluggable
125mW
U.FL or chip
RM024-S10-C-XX
Surface Mount
10mW
U.FL
RM024-S10-M-XX
Surface Mount
10mW
U.FL or chip
RM024-P10-C-XX
Pluggable
10mW
U.FL
RM024-P10-M-XX
Pluggable
10mW
U.FL or chip
Antenna Information
RM024 family has been designed to operate with the antennas listed below and having a maximum
gain of 9dBi. The required antenna impedance is 50 ohms.
Item
Part Number
Mfg.
Type
Gain (dBi)
1
WIC2450-A
Laird Technologies
Chip
2
2
S181-6-PX-2450S
Nearson
Dipole
2
The OEM is free to choose another vendor’s antenna of like type and equal or lesser gain as
an antenna appearing in the table and still maintain compliance. Refer ence FCC Part
15.204(c)(4) for further information on this topic.
To reduce potential radio interference to other users, the antenna type and gain should be
chosen so that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
permitted for successful communication.
OEM RESPONSIBILITIES
WARNING: The OEM must ensure that FCC labeling requirements are met. This includes a clearly visible
label on the outside of the OEM enclosure specifying the appropriate Laird Technology FCC identifier for this
product as well as the FCC notice below.
Contains FCC ID: KQL-RM02410
IC: 2268C-RM02410
The enclosed device complies with Part 15 of the FCC Rules and Industry Canada License Exempt
RSS Standard(s). Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation
Label and text information should be in a size of type large enough to be readily legible, consistent with
the dimensions of the equipment and the label. However, the type size for the text is not required to be
larger than eight point.
CAUTION: The OEM should have their device which incorporates the RM024 tested by a qualified test
house to verify compliance with FCC Part 15 Subpart B limits for unintentional radiators.
WARNING: This device has been tested with an U.FL connector and the antennas listed in the table
above. When integrated into the OEM’s product, these fixed antennas require professional installation
preventing end-users from replacing them with non-approved antennas. Any antenna not listed in the
above table must be evaluated for compliance with FCC Part 15.203 for unique antenna connectors.
Contact Laird Technology for assistance.
CAUTION: Any changes or modifications not expressly approved by Laird Technology could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does not cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to correct the interference by one or more of the following measures:
Re-orient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment to an outlet on a circuit that is different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION:
“THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES AND INDUSTRY CANADA LICENSE-EXEMPT RSS
STANDARD(S). OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.”
Industry Canada (IC) Caution:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
French equivalent is:
Le présent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.

Navigation menu