Land Pride At 2560 Users Manual
!! Land-29 Land Pride Lawn Mower Manuals - Lawn Mower Manuals – The Best Lawn Mower Manuals Collection
FD2560 to the manual ca7b9f92-ba66-47d1-bf7e-6142e29b11bd
2015-02-09
: Land-Pride Land-Pride-At-2560-Users-Manual-569826 land-pride-at-2560-users-manual-569826 land-pride pdf
Open the PDF directly: View PDF 
.
Page Count: 27
| Download | |
| Open PDF In Browser | View PDF |
Table of Contents
Grooming Mower, 3-spindle
FD2560, FD2572, AT2560 & AT2572
10618
14326
310-148M
Operator’s Manual
!
Read the Operator’s manual entirely. When
you see this symbol, the subsequent
instructions and warnings are serious - follow
without exception. Your life and the lives of
others depend on it!
© Copyright 2006 Printed
10/11/06
Cover photo may show optional equipment
not supplied with standard unit.
Land Pride
Table of Contents
Table of Contents
Important Safety Information . . . . . . . . . . .1
Section 4: Maintenance and Lubrication 16
Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General Maintenance . . . . . . . . . . . . . . . . . . . . . . 16
Blade Inspection . . . . . . . . . . . . . . . . . . . . . . . 16
Blade Sharpening . . . . . . . . . . . . . . . . . . . . . . 16
Blade Replacement . . . . . . . . . . . . . . . . . . . . . 17
AIR TIRES (AIR PRESSURE): . . . . . . . . . . . . 17
V-Belt Installation . . . . . . . . . . . . . . . . . . . . . . 17
Belt Tension . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Service Daily . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Service Every 50 Hours Of Operation: . . . . . . 18
PTO U-Joint . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PTO Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Wheel Bushing (Martin) . . . . . . . . . . . . . . . . . . 19
Wheel Bushing (Neilson) . . . . . . . . . . . . . . . . . 19
Bearing in Blade Spindle Hubs . . . . . . . . . . . . 19
Wheel Support Bushings . . . . . . . . . . . . . . . . . 19
Introduction . . . . . . . . . . . . . . . . . . . . . . . .8
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 8
Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 8
Serial Number Plate . . . . . . . . . . . . . . . . . . . . . 8
Further Assistance . . . . . . . . . . . . . . . . . . . . . . 8
Section 1: Assembly & Set-up . . . . . . . . . .9
General Description . . . . . . . . . . . . . . . . . . . . . . . . 9
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . 9
Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . 9
Upper Hitch Arms . . . . . . . . . . . . . . . . . . . . . . . 9
Lower Hitch Lugs . . . . . . . . . . . . . . . . . . . . . . . 9
Initial Hitch Arm Position . . . . . . . . . . . . . . . . . . 9
Gauge Wheel Assembly . . . . . . . . . . . . . . . . . 10
Grass Chute Assembly . . . . . . . . . . . . . . . . . . 10
Final Inspection . . . . . . . . . . . . . . . . . . . . . . . . 10
Section 5: Options . . . . . . . . . . . . . . . . . .20
Section 6: Specifications & Capacities . .21
Section 2: Operating Instructions . . . . . .11
Section 7: Troubleshooting . . . . . . . . . . .22
General Description . . . . . . . . . . . . . . . . . . . . . . . 11
Pre-Start Instructions . . . . . . . . . . . . . . . . . . . . . . 11
Tractor Requirements . . . . . . . . . . . . . . . . . . . 11
Tractor Hook-Up . . . . . . . . . . . . . . . . . . . . . . . 11
Driveline Installation . . . . . . . . . . . . . . . . . . . . . . . 11
Checking Driveline Minimum Length . . . . . . . . 12
Operating Instructions . . . . . . . . . . . . . . . . . . . . . 13
Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Section 8: Appendix . . . . . . . . . . . . . . . . .23
Torque Values Chart . . . . . . . . . . . . . . . . . . . . . . 23
Tire Inflation Chart . . . . . . . . . . . . . . . . . . . . . . . . 23
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Section 3: Adjustments . . . . . . . . . . . . . .14
Mower Chute . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Floating & Front To Back Hitch Adjustments . . . . 14
Leveling The Mower . . . . . . . . . . . . . . . . . . . . . . 14
Four Gauge Wheels . . . . . . . . . . . . . . . . . . . . 14
Cutting Height Adjustment . . . . . . . . . . . . . . . . . . 15
Belt Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
© Copyright 2006 All rights Reserved
Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land
Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves
the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
Land Pride is a registered trademark.
All other brands and product names are trademarks or registered trademarks of their respective holders.
Printed in the United States of America.
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Land Pride
▲
Table of Contents
Important Safety Information
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Safety at All Times
Look For The Safety Alert Symbol
Thoroughly read and understand
the instructions given in this
manual before operation. Refer to
the “Safety Label” section, read
all instructions noted on them.
Do not allow anyone to operate
this equipment who has not fully
read and comprehended this
manual and who has not been
properly trained in the safe
operation of the equipment.
The SAFETY ALERT SYMBOL indicates there is a
potential hazard to personal safety involved and extra
safety precaution must be taken. When you see this
symbol, be alert and carefully read the message that
follows it. In addition to design and configuration of
equipment, hazard control and accident prevention
are dependent upon the awareness, concern,
prudence and proper training of personnel involved in
the operation, transport, maintenance and storage of
equipment.
▲ Operator should be familiar with
all functions of the unit.
▲ Operate implement from the
driver’s seat only.
▲ Make sure all guards and shields
are in place and secured before
operating the implement.
▲ Do not leave tractor or implement
unattended with engine running.
▲ Dismounting from a moving
tractor could cause serious injury
or death.
▲ Do not stand between the tractor
and implement during hitching.
▲ Keep hands, feet, and clothing
away from power-driven parts.
▲ Wear snug fitting clothing to avoid
entanglement with moving parts.
▲ Watch out for wires, trees, etc.,
when raising implement. Make
sure all persons are clear of
working area.
▲ Turning tractor too tight may
cause implement to ride up on
wheels. This could result in injury
or equipment damage.
!
Be Aware of
Signal Words
A Signal word designates a degree or
level of hazard seriousness. The
signal words are:
! DANGER
Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury. This
signal word is limited to the most
extreme situations, typically for
machine components that, for
functional purposes, cannot be
guarded.
! WARNING
Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury, and
includes hazards that are exposed
when guards are removed. It may also
be used to alert against unsafe
practices.
! CAUTION
Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
For Your Protection
Shutdown and Storage
▲ Thoroughly read and understand
the “Safety Label” section, read all
instructions noted on them.
▲ Lower machine to ground, put
tractor in park, turn off engine, and
remove the key.
▲ Detach and store implements in a
area where children normally do
not play. Secure implement by
using blocks and supports.
OFF
REMO
VE
10/11/06
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
1
Table of Contents
Land Pride
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Use Safety
Lights and Devices
Transport
Machinery Safely
▲ Slow moving tractors, selfpropelled equipment, and towed
implements can create a hazard
when driven on public roads. They
are difficult to see, especially at
night.
▲ Flashing warning lights and turn
signals are recommended
whenever driving on public roads.
Use lights and devices provided
with implement.
▲ Comply with state and local laws.
▲ Maximum transport speed for
implement is 20 mph. DO NOT
EXCEED. Never travel at a speed
which does not allow adequate
control of steering and stopping.
Some rough terrain require a
slower speed.
▲ Sudden braking can cause a
towed load to swerve and upset.
Reduce speed if towed load is not
equipped with brakes.
Practice Safe Maintenance
Use A Safety Chain
▲ A safety chain will help control
drawn machinery should it
separate from the tractor
drawbar.
▲ Use a chain with the strength
rating equal to or greater than
the gross weight of the towed
machinery.
▲ Attach the chain to the tractor
drawbar support or other
specified anchor location. Allow
only enough slack in the chain to
permit turning.
▲ Do not use safety chain for
towing.
2
▲ Understand procedure before
doing work. Use proper tools and
equipment, refer to Operator’s
Manual for additional information.
▲ Work in a clean dry area.
▲ Lower the implement to the
ground, put tractor in park, turn off
engine, and remove key before
preforming maintenance.
▲ Allow implement to cool
completely.
▲ Install all transport locks on raised
drill before working underneath, refer
to the Operator’s Manual for quantity
and location of transport locks.
▲ Do not grease or oil implement
while it is in operation.
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
▲ Use the following maximum
speed - tow load weight ratios as
a guideline:
▲ 20 mph when weight is less than
or equal to the weight of tractor.
▲ 10 mph when weight is double
the weight of tractor.
▲ IMPORTANT: Do not tow a load
that is more than double the
weight of tractor.
▲ Move the opener handle to the
“ROAD” position and complete
raising the openers to lock them
up before working underneath
them.
▲ Disk edges are sharp. Be careful
when working in this area.
▲ Disconnect battery ground cable
(-) before servicing or adjusting
electrical systems or before
welding on implement.
▲ Inspect all parts. Make sure parts
are in good condition & installed
properly.
▲ Remove buildup of grease, oil or
debris.
▲ Remove all tools and unused pars
from implement before operation.
10/11/06
Table of Contents
Land Pride
Important Safety Information
These are common practices that may or may not be applicable to the products described in
this manual.
Prepare for Emergencies
▲ Be prepared if a fire starts.
▲ Keep a first aid kit and fire
extinguisher handy.
▲ Keep emergency numbers for
doctor, ambulance, hospital and
fire department near phone.
Wear
Protective Equipment
▲ Protective clothing and equipment
should be worn.
▲ Wear clothing and equipment
appropriate for the job. Avoid
loose fitting clothing.
▲ Prolonged exposure to loud noise
can cause hearing impairment or
hearing loss. Wear suitable
hearing protection such as
earmuffs or earplugs.
▲ Operating equipment safely
requires the full attention of the
operator. Avoid wearing radio
headphones while operating
machinery.
911
Keep Riders
Off Machinery
▲ Riders obstruct the operator’s
view, they could be struck by
foreign objects or thrown from the
machine.
▲ Never allow children to operate
equipment.
10/11/06
Tire Safety
▲ Tire changing can be dangerous
and should be preformed by
trained personnel using the
correct tools and equipment.
▲ When inflating tires, use a clip-on
chuck and extension hose long
enough to allow you to stand to
one side and NOT in front of or
over the tire assembly. Use a
safety cage if available.
▲ When removing and installing
wheels, use wheel handling
equipment adequate for the
weight involved.
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
3
Table of Contents
Land Pride
Important Safety Information
Safety Labels
Your Grooming Mower comes equipped with all safety
labels in place. They were designed to help you safely
operate your implement. Read and follow their
directions.
1.
2.
3.
Keep all safety labels clean and legible.
Replace all damaged or missing labels. To order new
labels go to your nearest Land Pride dealer or visit our
dealer locator at landpride.com.
Some new equipment installed during repair requires
4.
safety labels to be affixed to the replaced component as
specified by Land Pride. When ordering new components
make sure the correct safety labels are included in the
request.
Refer to this section for proper label placement.
To install new labels:
a. Clean the area the label is to be placed.
b. Spray soapy water on the surface where the label is to
be placed.
c. Peel backing from label. Press firmly onto the surface.
d. Squeeze out air bubbles with the edge of a credit card.
818-555C
Rotating Blade Hazard
(Flat Deck)
13098
818-555C
Rotating Blade Hazard
(Air Tunnel)
13100
818-556C
Thrown Object Hazard
(Flat Deck)
13098
4
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Land Pride
Table of Contents
Important Safety Information
818-556C
13100
Thrown Object Hazard
(Air Tunnel)
818-130C
13099
13101
13099
Operate at 540 RPM
PTO (Flat Deck)
818-130C
Operate at 540 RPM
PTO (Air Tunnel)
818-142C
Rotating Driveline Hazard
(Flat Deck)
10/11/06
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
5
Table of Contents
Land Pride
Important Safety Information
818-142C
13101
Rotating Driveline Hazard
(Air Tunnel)
818-144C
13099
13101
V-Belt Instructions
(Flat Deck)
818-144C
V-Belt Instructions
(Air Tunnel)
6
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Land Pride
Table of Contents
Important Safety Information
13102
818-540C
Danger Guard Missing
ROTATING DRIVELINE
KEEP AWAY!
13102
818-552C
Danger Rotating Driveline
10/11/06
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
7
Table of Contents
Land Pride
Introduction
Introduction
Land Pride welcomes you to the growing family of new
product owners.
This Grooming Mower has been designed with care and
built by skilled workers using quality materials. Proper
assembly, maintenance and safe operating practices will
help you get years of satisfactory use from the machine.
Serial Number Plate
For prompt service always use the serial number and
model number when ordering parts from your Land Pride
dealer. Be sure to include your serial and model numbers
in correspondence also. Refer to Figure 1 for the location
of your serial number plate.
Using This Manual
• This Operator’s Manual is designed to help familiarize
•
•
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.
The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.
To order a new Operator’s or Parts Manual contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge from our website at
www.landpride.com or printed from the Land Pride
Service & Support Center by your dealer.
Terminology
“Right” or “Left” as used in this manual is determined by
facing the direction the machine will operate while in use
unless otherwise stated.
Definitions
NOTE: A special point of information that the
operator must be aware of before continuing.
IMPORTANT: A special point of information related
to its preceding topic. Land Pride’s intention is that
this information should be read and noted before
continuing.
Owner Assistance
15035
Serial Number Plate Location
Figure 1
Further Assistance
Your dealer wants you to be satisfied with your new
Grooming Mower. If for any reason you do not
understand any part of this manual or are not satisfied
with the service received, the following actions are
suggested:
1. Discuss the matter with your dealership service
manager making sure he is aware of any problems
you may have and that he has had the opportunity to
assist you.
2. If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem and request assistance.
3. For further assistance write to:
The Warranty Registration card should be filled out by
the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.
If customer service or repair parts are required contact a
Land Pride dealer. A dealer has trained personnel, repair
parts and equipment needed to service the Grooming
Mower.
Land Pride Service Department
1525 East North Street
P.O. Box 5060
Salina, Ks. 67402-5060
E-mail address
lpservicedept@landpride.com
The parts on your Grooming Mower have been specially
designed and should only be replaced with genuine Land
Pride parts. Therefore, should your mower require
replacement parts go to your Land Pride Dealer.
8
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Table of Contents
Land Pride
Section 1: Assembly & Set-up
Section 1: Assembly & Set-up
General Description
Lower Hitch Lugs
The 25 Series Grooming Mower is shipped crated and
partially assembled. Unloading and assembly of this
grooming mower is the responsibility of the Land Pride
Dealer. The mower should be completely assembled,
lubricated, and Adjusted for normal mowing operations
before delivery to the customer.
Refer to Figure 1-3
The Hitch Lug (#1) is installed from the factory in the
inward most position on the mower channel (#2).
Tools Required
1. Remove hair pin (#4). Remove pivot pin (#3)
2. Slide hitch lugs (#1) into the initial position as shown
in Figure 1-4.
• Sufficient Lifting device (e.g., fork lift, hoist, tractor) see
•
•
•
“Specification Chart” for unit weight.
Support Stands
Regular Hand Tools
Grease Gun
!
CAUTION
Always wear personal protection devices such as eye, ear, and
feet protectors during assembly operations.
Assembly Instructions
Using a safe lifting device, set the crate on safe
supporting stands. Remove crate. Remove loose
components - gauge wheels, gauge wheel arms and
miscellaneous hardware from the top of deck. Arrange
parts for easy identification.
Upper Hitch Arms
Refer to Figure 1-2:
1. Loosen 5/8" x 1 3/4" long bolts (#1) and swing upper
hitch (#2) up to a vertical position.
2. Remove 5/8" x 5 1/2" long bolt (#3) and install upper
hitch brace (#4), upper pivoting hitch (#5), and hitch
spacer (#6) with 5/8" x 5 1/2" long bolt (#3).
3. Refer to Figure 1-4, for initial bolting location of upper
hitch brace (#4).
13543
Lower Hitch Lugs
Figure 1-3
Initial Hitch Arm Position
Refer to Figure 1-4
1. Bolt the upper hitch arms and lower hitch lugs on the
mower to the positions shown
2. Tighten hardware to listed torque values.
11915
13542
Upper Hitch Arms Assembly
Figure 1-2
10/11/06
Initial Hitch Arm Position
Figure 1-4
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
9
Table of Contents
Land Pride
Section 1: Assembly & Set-up
Gauge Wheel Assembly
Grass Chute Assembly
Refer to Figure 1-5:
1. The rear gauge wheel arms (#1) are bolted to the
frame backwards from factory. Remove the 3/8" x 3"
long bolt (#2), hardware and gauge wheel arm (#1).
2. Bolt the rear gauge wheel arms (#1) to the mounting
channels on the mower frame using 3/8" x 3" long
bolt (#2) and hardware shown.
3. Insert the 1" diameter shaft of the gauge wheel yoke
(#3) into the bushings on the gauge wheel arm (#1),
noting the amount of spacers (#4) added to top or
bottom depending on cutting height {refer to Section
3 “Cutting Height Adjustments” on Page 15}.
4. Secure shaft to wheel arm with 1/4" lock pin (#5). Be
sure all the spacers are arranged the same on each
wheel assembly. Tighten all hardware to values
listed in the “Torque Values Chart” in the appendix.
Refer to Figure 1-5:
1. Loosen upper pivot bolt (#1) and remove lower
thumb screw (#2).
Hinge chute down and install thumb screw (#2) and flat
washer(#3). When set at position desired, tighten down
upper pivot bolt (#1) and lock nut (#4). Do not tighten
completely. Allow chute to hinge. Lock down lower
thumb screw (#2) with flat washer (#3).
2.
13544
Grass Chute Assembly
Figure 1-6
Final Inspection
After completing the “Dealer Assembly and Setup”
section, fill out the “Warranty Registration Form &
Inspection Report” in this manual.
13577
Gauge Wheel Assembly
Figure 1-5
10
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Land Pride
Table of Contents
Section 2: Operating Instructions
Section 2: Operating Instructions
General Description
The operator is responsible for the safe use of this
machine. Read and understand the safety section before
continuing.
This section covers the procedures needed to operate
this machine. Properly read and understand this section
before operating.
Pre-Start Instructions
Tractor Requirements
This mower is designed with a 3-Point category I hitch.
Horse power rating of the tractor should not exceed 30 PTO
horse power on 60 inch units and 35 PTO horse power on
72 inch units. PTO Speed of tractor should be 540 RPM.
NOTE: In order to maintain steering control, ballast
may have to be added to your tractor. To determine
whether or not to add ballast, refer to your tractor
operator’s manual for weight requirements and to the
“Specifications and Capacities” chart for the weight
of the unit.
Front Position Hitch Adjustment
Figure 2-1
Tractor Hook-Up
1. Be certain that the tractor draw bar will not interfere.
Move draw bar ahead or remove if required. Draw bar
should also be checked for clearance when unit is
being raised for the first time.
2. Align lower link arms of tractor to hitch lugs on
mower. Insert lower hitch pins into lower ball swivels
and attach lynch pins.
3. Referring to Figure 2-1, attach tractor top link to
upper floating hitch on mower with pin supplied.
4. Adjust the tractor top link in or out to place the upper
hitch pin vertically above the lower hitch pins as
shown in Figure 2-2, to allow mower flotation.
11915
NOTE: The initial position of the Upper Hitch Arms
and the Lower Hitch Lugs should be in the back
position. If there is a clearance problem refer to the
“Adjustment Section” under “Floating & Front To
Back Hitch Adjustments” page 14.
Driveline Installation
An additional driveline may be required if the mower is to
be used on more than one tractor especially if a quick
hitch is used.
!
CAUTION
Do not use a PTO adaptor with a quick hitch. A PTO adapter
will increase strain on the tractor’s PTO shaft resulting in
possible damage the shaft and driveline.
!
Back Position Floating Hitch Adjustment
Figure 2-2
!
!
WARNING
10/11/06
WARNING
Damaged drivelines can cause serious injury or death.
!
Damaged drivelines can cause serious injury or death.
CAUTION
Tractor PTO shield and all Grooming Mower guards must be
in place at all times during operation!
CAUTION
Always engage parking brake, shut off tractor and remove key
before dismounting from tractor.
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
11
Table of Contents
Land Pride
Section 2: Operating Instructions
IMPORTANT: Some tractors are equipped with
multi-speed PTO ranges. Be certain your tractor ‘s
PTO is set for 540 rpm.
IMPORTANT: Avoid premature driveline
breakdown. A driveline that is operating must not
exceed an angle of 25 degrees up or down while
operating the 3-point lift. See Figure 2-3 below.
13800
Maximum PTO driveline Movement During Operation
Figure 2-3
IMPORTANT: Always check driveline minimum
length during initial setup, when connecting to a
different tractor and when alternating between using
a quick hitch and a standard 3-point hitch. More than
one driveline may be required to fit all applications.
IMPORTANT: It is necessary to aligning the tractor’s
PTO shaft level with the gearbox shaft when
checking driveline minimum length. Too long a
driveline can damage tractor, gearbox and driveline.
4. The driveline will require shortening if it is too long to
fit between tractor and gearbox. Shorten driveline as
follows:
a. Raise or lower 3-point lower arms until gearbox
and tractor PTO shafts are approximately level
with each other. Securely block mower frame in
this position.
b. Set tractor in park, shut tractor engine off, set park
brake and remove switch key.
c. Pull driveline apart into two sections as shown in
Figure 2-4. Attach outer driveline universal joint to
the tractor PTO shaft. Attach inner driveline
universal joint to the gearbox shaft. Pull on each
driveline section to be sure universal joints are
secured to the shafts.
d. Hold driveline sections parallel to each other to
determine if they are too long. The inner and outer
shields on each section should end approximately
1" short of reaching the universal joint shield on
the adjacent section (see “B” dimension). If they
are too long, measure 1" (“B” dimension) back
from the universal joint shield and make a mark at
this location on the inner and outer driveline
shields.
e. Cut off inner shield at mark (“X” dimension). Cut
same amount off inner shaft (“X1” dimension).
Repeat cut off procedure (“Y” & “Y1” dimensions)
to cut outer driveline half.
5.
6.
7.
8.
f. Remove all burrs and cuttings.
Apply multi-purpose grease to the inside of the outer
driveline shaft and reassemble the two shafts.
Attach inner driveline yoke to the gearbox shaft.
Attach outer driveline yoke to the tractor's PTO shaft.
The driveline should now be moved back and forth to
insure that both ends are secured to the tractor and
gearbox PTO shafts. Reattach any end that is loose.
IMPORTANT: Two small chains are supplied with
the driveline. These chains must be attached to
outer and inner driveline yoke shields and to the
cutter deck and tractor to restrict driveline shields
from rotating.
22009
Shortening the PTO Shafts
Figure 2-4
Checking Driveline Minimum Length
Refer to Figure 2-4:
1. Start tractor and slowly engage 3-point to move
lower arms until the gearbox shaft is approximately
level with tractor's PTO shaft.
2. Slide inner yoke of the driveline over the gearbox
shaft and secure with locking collar.
3. Slide outer yoke of driveline over the tractor PTO
shaft and secure with locking collar. Skip to step 5 on
page 12 if driveline fits between tractor and gearbox.
12
9. Hook one of the driveline safety chains in a hole on
the outer driveline yoke shield and the opposite end
to the tractor to restrict outer shield rotation.
10. Hook the second driveline safety chain in a hole on
the inner driveline yoke shield and the opposite end
to the mower to restrict inner shield rotation.
11. Start tractor and raise the Grooming Mower just
enough to remove blocks used to support the mower
frame in step 4a above.
12. Slowly engage the tractor’s hydraulic 3-point to lower
the mower. Check for sufficient drawbar clearance.
Move drawbar ahead, aside or remove if required.
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Table of Contents
Land Pride
Section 2: Operating Instructions
Transporting
Operating Instructions
!
Pre-Start-up Checklist
CAUTION
Always disengage tractor PTO before transporting mower to
avoid injury from thrown objects or blade contact.
Read and follow the “Safety Rules” carefully.
Oil Level in gearbox
All plugs and caps in gearbox have been replaced and tightened properly.
All mower blades, bolts & nuts are tight
Inspect the blades. Make note of the wear to the blades and
the sharpness of the blades.
!
CAUTION
When traveling on public roads whether at night or during the
day, use accessory lights and devices for adequate warning to
operator’s of other vehicles. Comply with all federal, state and
local laws.
All guards and shields are in place and secure.
Grease PTO shaft and all other grease fittings.
Make a thorough examination of the PTO shafts. Also check
the connection to the gearbox and tractor PTO.
Clear the area to be mowed of rocks, branches and other foreign objects.
1. Clear the area to be mowed of objects and debris
that might be picked up and thrown by the mower
blades.
2. Grass is best cut when it is dry. Mowing wet grass
can cause plugging resulting in grass clumps behind
the mower.
3. Grass should be mowed frequently as shorter
clippings deteriorate faster.
4. If mowing extremely tall grass, it is best to raise
cutting height and mow the area, then lower cutting
height and mow a second time at the desired height.
5. Lower mower to ground. Set tractor throttle at
approximately 1/4 open. Engage PTO to start blades
rotating.
6. Operate only with 540rpm PTO tractor.
7. At first, begin mowing at a slow forward speed and
shift up until the desired speed is achieved maintaining 540 PTO rpm.
8. Mower blades will cut better at a faster rotor speed
than at reduced throttle.
9. After mowing the first 50 feet, stop and check to see
that the mower is adjusted properly.
10. Do not make sharp turns or attempt to back up while
mower is on the ground.
11. Do not engage PTO with mower in the fully raised
position. Do not engage PTO at full throttle.
12. After mowing disconnect tractor PTO and follow
transporting procedures.
!
!
CAUTION
The mower is wider than your tractor so care should be taken
when encountering oncoming traffic and roadside obstructions.
IMPORTANT: Always disengage PTO before raising
the mower to transport position.
1. When raising the mower to the transport position, be
sure that driveline does not contact tractor or mower.
Adjust the tractor’s 3-point hitch lift height so that the
PTO shaft does not contact the mower deck. Mower
should not be transported without tractor’s upper 3Point link attached.
2. Be sure to reduce tractor ground speed when
turning; and, leave enough clearance so the mower
does not contact obstacles such as buildings, trees
or fences.
3. Select a safe ground travel speed when transporting
from one area to another. When traveling on
roadways, transport in such a way that faster moving
vehicles may pass you safely.
4. When traveling over rough or hilly terrain, shift tractor
to a lower gear.
CAUTION
When mowing in sandy soil areas, wear may occur to your
mower blades caused from sand erosion. Frequent inspection
should be made and blades replaced if damaged
10/11/06
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
13
Table of Contents
Land Pride
Section 3: Adjustments
Section 3: Adjustments
!
CAUTION
Disengage PTO, engage parking brake, shut off tractor, and
remove key before making any adjustments!
Mower Chute
This mower is equipped with an adjustable grass
discharge chute. Adjustments can be made by loosening
the bolts on the front and rear of mower chute. With the
mower chute in the raised operating position, grass is
expelled away from the mower for a more even
distribution of grass clippings. Lowering the mower chute
will decrease the distance the grass is discharged from
the mower.
!
11023
DANGER
Middle Position Floating Hitch Adjustment
Figure 3-2
DO NOT in any condition operate mower with chute removed
Floating & Front To
Back Hitch Adjustments
The 3-point hitch system on this mower has been
designed for front to back flotation when mowing on
uneven terrain. The lower 3-point hitch blocks also are
adjustable from front to back for additional field float and
tractor clearance. The lower hitch blocks and top link rear
braces can be adjusted front to back as shown in Figure
3-1 and Figure 3-2, Middle Position Floating Hitch
Adjustment, in lFigure 3-2. Deviation from the 3 setting
will limit field float.
NOTE: Positioning the Upper Hitch Arms and Lower
Hitch Lugs to the back setting shortens overall tractor/
mower length allowing tighter turns and increasing
lifting power.
11917
Back Position Hitch Adjustment
Figure 3-3
Leveling The Mower
Four Gauge Wheels
NOTE: Tractor and mower should be on level ground.
Front Position Hitch Adjustment
Figure 3-1
14
1. Set lower hitches and upper floating hitch, as shown
in Figure 3-1, Figure 3-2, or Figure 3-3.
2. Make sure PTO is disengaged and start tractor.
3. Raise mower, watching that tractor draw bar (if not
removed) does not interfere with mower.
4. Slowly lower the mower until gauge wheels touch the
ground and the lower mower 3-point hitch bars are
parallel to the ground in floating position. Set the
tractor’s 3-point stop.
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Land Pride
Table of Contents
Section 3: Adjustments
5. Set the parking brake and turn off tractor. Remove
key from ignition.
6. Adjust the tractor top link in or out to place the upper
hitch pin vertically above the lower hitch pin as
shown in Figure 3-1, Figure 3-2, or Figure 3-3, to
allow mower flotation.
7. Rotate blades in line with direction of travel.
8. Measure the clearance from the cutting edge to the
ground at front and rear of the blade. This
measurement should be equal or have the blade at
the front of the mower not more than 1/2" lower than
the blade at the rear of the mower.
Cutting Height Adjustment
12732
1. Using the tractor, raise the mower off the ground and
support under it with secure blocking so not to let the
mower drift down during maintenance.
2. Holding wheel and yoke assembly up, remove quicklock pin from top of gauge wheel spindle. Position full
length spacers and half spacer as required. All
spacers on top of spindle tube allows for
approximately 1" cutting height. Adjustments range
from 1" to a maximum of 5 1/2" in 1/2" increments.
Refer to “Leveling The Mower” page 14.
!
Belt Tension
Figure 3-4
CAUTION
Engage parking brake, shut off tractor, remove key and
disengage PTO before making any height adjustments!
Belt Tension
Refer to Figure 3-4:
!
CAUTION
Belt drive system under spring tension; use care to avoid bodily
harm!
1. To check tension apply force at arrow A. With a
tension tester and deflect the belt 1/4". The force
required to get this deflection should range from 7 to
10 lbs.
2. To adjust belt tension, adjust eyebolt (#1), as
necessary. This adjustment will increase or decrease
the tension on spring (#2).
3. Excessive tension on the belt may lead to premature
failure of belt and drive components. Excessive
tension on the belt may also lead to a safety hazard
to the operator or bystanders. Not enough tension on
the belt may lead to premature failure of the belt due
to excessive slipping.
4. Excessive tension on the belt may lead to premature
failure of belt and drive components. Excessive
tension on the belt may also lead to a safety hazard
to the operator or bystanders.
10/11/06
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
15
Table of Contents
Land Pride
Section 4: Maintenance and Lubrication
Section 4: Maintenance and Lubrication
Proper servicing and adjustment is the key to the long life
of any implement. With careful and systematic
inspection, you can avoid costly maintenance, time and
repair.
After using your Grooming Mower for several hours,
check all bolts to be sure they are tight.
Replace any worn, damaged or illegible safety labels by
obtaining new labels from your Land Pride Dealer.
!
CAUTION
For Safety reasons, each maintenance operation must be
performed with the tractor’s PTO disengaged, the mower
lowered completely, tractor engine shut off and ignition key
removed.
General Maintenance
Blade Inspection
Refer to Figure 4-1:
NOTE: Blade Wear: As blades wear and are
sharpened, the blade performance will be reduced.
!
Blade Sharpening
IMPORTANT: Always install blade with the cutting
edge facing direction of rotation.
IMPORTANT: Replace blades with Land Pride
blades only.
!
CAUTION
ALWAYS wear eye protection and gloves when sharpening a
blade.
1. If the blade cutting edge is dull or nicked, it should be
replaced or sharpened. Remove blades for replacing
or sharpening by grasping the end of the blade using
a rag or a thick, padded glove, while loosening and
removing the bolt/bolts that mount the blade.
2. Clean blade, blade washer and mounting surface of
all debris before replacing or sharpening.
NOTE: Care should be taken in order not to remove
any more material than necessary to sharpen blade.
3. Grind cutting edge at the same bevel as the original.
See Figure 4-2. Sharpen only the top of the cutting
edge to maintain sharpness.
DANGER
Bent, Deformed or Split Blades: Should be removed from unit
and discarded. DO NOT attempt to straighten for reuse.
!
WARNING
DO NOT attempt to modify blade, such as hard surfacing, heat
or cold treating and/or by any other method.
!
DANGER
DO NOT try to straighten a blade that is bent. Never weld a
broken or cracked blade. ALWAYS replace with a new Land
Pride blade to assure safety.
19327
Blade Sharpening
Figure 4-2
Inspection of Blades & Sharpening
Figure 4-1
16
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Table of Contents
Land Pride
Section 4: Maintenance and Lubrication
4. Check blade balance by positioning the blade
horizontally on a nail or shaft through the center hole.
See Figure 4-3. If either end of the blade rotates
downward, grind (remove) metal on that end until the
blade will balance. The blade is properly balanced
when neither end drops. Balance of a blade is
generally maintained by removing an equal amount
of material from each end of the blade when
sharpening.
HORIZONTAL
2. Move belt take-up handle in a clockwise direction to
relieve tension on belt.
3. With tension relieved from belt remove old belt from
pulleys.
4. Install new belt referring to the figure below (also
refer to the decal on top of mower deck). Be sure belt
is positioned in all the pulley grooves. Release belt
take-up handle to apply tension to new belt.
5. Reinstall all belt covers and secure in place with
hardware.
Belt Tension
19046
!
NAIL OR SHAFT
Blade Balancing
Figure 4-3
Blade Replacement
IMPORTANT: Always install blade with cutting edge
facing direction of blade spindle rotation and wing
tips pointing up towards bottom of deck.
1. Remove cap screw and blade washer from blade to
be replaced. Remove blade.
2. Install blade washer into center hole on blade.
3. Replace cap screw. Tighten bolts to proper torque,
see the “Torque Values Chart” section on page 23.
IMPORTANT: Replace blades with Land Pride
blades only.
1. Belt tension should be checked after approximately
20 hours of operation on a new belt.
2. Not enough tension on the belt may lead to
premature failure of the belt due to excessive
slipping of the belt.
Refer to “Belt Tension” on page 15 for proper
adjustment of belt tension.
!
WARNING
Excessive tension on the belt may lead to premature failure of
belt and drive components. Excessive tension on the belt may
also lead to a safety hazard to the operator or bystanders.
Storage
AIR TIRES (AIR PRESSURE):
Tire Sealant: Heavy Duty tire sealant has been added in
Air tires to help reduce air loss from punchers due to
nails/thorns etc....
NOTE: Under inflated tires can roll off of rim.
Maintaining air pressure within 5 PSI of maximum tire
pressure reduces the risk of tires rolling off of rim.
V-Belt Installation
1. Remove right hand, left hand and center belt covers.
V-Belt Installation, Routing & Rotation Decal
Figure 4-4
10/11/06
CAUTION
Belt drive system under spring tension; use care to avoid bodily
harm!
At the end of the working season or when the mower will
not be used for a long period, it is good practice to clean
off any dirt or grease that may have accumulated on the
mower and any of the moving parts. It may be necessary
to scrape off compacted dirt from the bottom of the deck,
then use a garden hose to thoroughly clean the surface.
1. Clean the mower as necessary. Be sure that the
mower is completely cleaned before storing.
2. Check the blades for wear and replace if necessary,
see “Maintenance” section on page 16.
3. Inspect the mower for loose, damaged or worn parts
and adjust or replace if needed.
4. Lubricate as noted in the “Lubrication” section on
page 18.
5. Remove mower drive belt from one pulley to release
drive belt tension.
6. Remove belt guards, thoroughly clean the top and
bottom of the mower frame.
7. Repaint parts where paint is worn or scratched to
prevent rust. Aerosol beige touch-up paint is
available from your dealer. Order Land Pride part
#821-011C.
8. Store mower in a clean, dry place for longer mower
life.
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
17
Table of Contents
Land Pride
Section 4: Maintenance and Lubrication
Lubrication
!
Service Every 50 Hours Of Operation:
CAUTION
For Safety reasons, each lubrication operation must be
performed with the tractor’s PTO disengaged, the mower
lowered completely, tractor engine shut off and ignition key
removed.
1. With the mower on level ground, check the oil level in
the gearbox by removing the plug in the side of the
box. The oil should reach the plug hole. If oil level is
low, remove the top plug in the gearcase and fill with
SAE 90 oil until oil flows from side port of the
gearbox. Reinstall plugs and retighten.
IMPORTANT: Do not overfill! Should your gearbox
require repair, take it to your Land Pride dealer.
Service Daily
1.
2.
3.
4.
Grease the PTO u-joints.
Wheel support bushings.
Wheel bushing.
Bearing in blade spindle hubs.
Lubrication
Legend
2. Disconnect PTO shaft from the tractor and slide
apart. Clean and coat the inner tube of the PTO shaft
with a light film of grease and then reassemble.
Multi-purpose
spray lube
Multi-purpose
grease lube
Multi-purpose
oil lube
50
Intervals in hours
at which lubrication
is required
8
Hours
PTO U-Joint
Coat PTO u-joint with grease every 8 hours of operation
Type of Lubrication: Multipurpose
12559
Quantity = Coat Generously
20
Hours
PTO Shaft
Disconnect PTO shaft from the tractor and slide apart.
Clean and coat the inner tube of the PTO shaft with a light
film of grease and then reassemble.
12559
Type of Lubrication: Multipurpose
Quantity = Light Film
Fill
Oil
Level
Fill
25
Oil
Level
Hours
Gearbox
Check the oil level in the gearbox by removing the bottom
plug in the back of the box. Add oil if necessary into the plug
on the top of the gearbox. Retighten both plugs.
Type of Lubrication: SAE 90 Oil
Quantity = Until oil reaches outside plug hole
16648
DO NOT
OVERFILL!
18
23582
IMPORTANT: Should your gearbox require repair,
take it to your Land Pride Dealer! Check oil level in
gearbox every 50 hours of operation.
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Land Pride
Table of Contents
Section 4: Maintenance and Lubrication
8
Hours
Wheel Bushing (Martin)
Until grease starts to purge.
Type of Lubrication: Multipurpose grease
13105
Quantity = Until grease starts to purge
8
Hours
Wheel Bushing (Neilson)
Type of Lubrication: Multipurpose grease
Quantity = Until grease starts to purge
13106
Seasonally
Bearing in Blade Spindle Hubs
Type of Lubrication: Multipurpose Grease
16656
Quantity = Until grease starts to purge from the top bearing. Top
bearing has a purge gap which allows grease to purge from it.
Seasonally
Wheel Support Bushings
Type of Lubrication: Multipurpose Grease
13111
10/11/06
Quantity = Until grease starts to purge.
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
19
Table of Contents
Land Pride
Section 5: Options
Section 5: Options
310-050A. . . . . . . . FRONT ROLLER REPL 310-050S
310-041S . . . . . . . . FRONT ROLLER BUNDLE
This Anti-Scalping Roller Package is available for those
customers who are concerned about scalping the grass
and ground with deck/blades. The roller will not allow
deck to scalp the ground with the leading edge of the
mower.
20
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Table of Contents
Land Pride
Section 6: Specifications & Capacities
Section 6: Specifications & Capacities
FD2560, FD2572, AT2560 & AT2572 3-Spindle Grooming Mower
FD2560
FD2572
AT2560
AT2572
Cutting Width
Description
60”
72”
60”
72”
Overall Width
71 1/2"
83"
71 1/2"
83"
Height
36"
36"
36"
36"
Length
56"
62"
56
62"
Weight
652#
718 #
652#
718#
1/4 x 2.5 x 20 29/32
Heat Treated
Alloy Steel
1/4 x 2.5 x 25
Heat Treated
Alloy Steel
1/4 x 2.5 x 20 29/32
Heat Treated
Alloy Steel
1/4 x 2.5 x 25
Heat Treated
Alloy Steel
15,000 FPM
16,195 FPM
14,500 FPM
15,500 FPM
Blades - 3
Blade Tip Speed
Cutting Height
1"-5 1/2" {1/2" Increments}
Deck Material Thickness
3/16"
Blade Overlap
1 1/2"
Blade Spindles
Greasable-Side
Hitch
Gauge Wheels: Optional Air
Gauge Wheels: Opt. Solid
Caster Wheel Spindle
Drive Train
Grass Chute
10/11/06
Cat. 1 Floating Clevis
Castered 10" x 4" Air Tires with Sealant
Castered 10" x 3 1/4" Solid Tire
1" Diameter With Greasable Bushing
540 RPM PTO; Gearbox 1:2.5 Ratio; Beveled Gears; Cast Iron Housing; Single V-Belt
Hinged-Adjustable
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
21
Table of Contents
Land Pride
Section 7: Troubleshooting
Section 7: Troubleshooting
Troubleshooting Chart
Problem
Discharge chute plugged
!
CAUTION
Do not try to clean discharge opening
when mower is running. Bodily harm
may occur.
Belt slipping
Patches of uncut grass
Excessive vibration
Cause
Solution
Belt not installed correctly
Check installation of belt
Grass too wet
Wait until grass dries
Grass too tall
Raise cutting height of mower and cut
grass twice
RPM of tractor too low
Mow at full throttle (540 PTO rpm) Check
PTO speed & tractor engine
Ground speed too fast
Shift transmission to a lower gear
Plugged grooming mower
Unplug and clean mower deck
Debris in sheaves
Remove belt guard shields and clean
sheaves
Worn belt
Replace belt
RPM of tractor too low
Mow at full throttle (540 PTO rpm). Check
PTO
speed & tractor engine
Ground speed too fast
Shift transmission to a lower gear
Blade damaged or dull
Sharpen & balance or replace blade
Power Take Off shaft or distribution shafts
bend
Replace Power Take Off or distribution
shafts
Blade broken or bent
Replace blade
Sheaves damaged or out of alignment
Replace sheaves or align
Drive belt damaged
Replace drive belt
Inadequate clearance between belt guard
shields & belt
Remove belt guard shields & clean debris
from belt area & sheaves
Mower in raised position & mower running
Readjust 3-point hitch to raise mower to
maximum of 14 inches
Gearbox noisy
Low lubricant level
Check lubricant level
Blades scalping grass
Cutting too low
Raise cutting height by adjusting wheels
Ridges in terrain
Change mowing pattern
Blades scalping grass
Uneven cut
Tractor loaded down by mower
22
Fast turning speed
Reduce speed on turns
Cutting too low
Raise cutting height by adjusting wheels
Ridges in terrain
Change mowing pattern
Fast turning speed
Reduce speed on turns
Ground speed too fast
Shift to a lower gear
Mower not level
Level mower
Dull blades
Sharpen blades & balance or replace
RPM of engine too low
Mow at full throttle (540 PTO rpm)
Ground speed too fast
Shift to a lower gear
Debris wrapped around mower spindles or
blades
Clean mower
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Table of Contents
Land Pride
Section 8: Appendix
Section 8: Appendix
Torque Values Chart
Bolt Head Identification
Bolt Head Identification
Bolt Size
(Inches)
in-tpi 1
1/4" - 20
1/4" - 28
5/16" - 18
5/16" - 24
3/8" - 16
3/8" - 24
7/16" - 14
7/16" - 20
1/2" - 13
1/2" - 20
9/16" - 12
9/16" - 18
5/8" - 11
5/8" - 18
3/4" - 10
3/4" - 16
7/8" - 9
7/8" - 14
1" - 8
1" - 12
1-1/8" - 7
1 1/8" - 12
1 1/4" - 7
1 1/4" - 12
1 3/8" - 6
1 3/8" - 12
Grade 2
Grade 5
Bolt Size
(Metric)
Grade 8
5.8
8.8
10.9
Class 5.8
Class 8.8
Class 10.9
N · m ft-lb 3 N · m ft-lb N · m ft-lb
mm x pitch N · m ft-lb N · m ft-lb N · m ft-lb
7.4
8.5
15
17
27
31
43
49
66
75
95
105
130
150
235
260
225
250
340
370
480
540
680
750
890
1010
M 5 X 0.8
M6X1
M 8 X 1.25
M8X1
M10 X 1.5
M10 X 0.75
M12 X 1.75
M12 X 1.5
M12 X 1
M14 X 2
M14 X 1.5
M16 X 2
M16 X 1.5
M18 X 2.5
M18 X 1.5
M20 X 2.5
M20 X 1.5
M24 X 3
M24 X 2
M30 X 3.5
M30 X 2
M36 X 3.5
M36 X 2
5.6
6
11
13
20
22
32
36
49
55
70
79
97
110
170
190
165
185
250
275
355
395
500
555
655
745
11
13
24
26
42
47
67
75
105
115
150
165
205
230
360
405
585
640
875
955
1080
1210
1520
1680
1990
2270
8
10
17
19
31
35
49
55
76
85
110
120
150
170
265
295
430
475
645
705
795
890
1120
1240
1470
1670
16
18
33
37
59
67
95
105
145
165
210
235
285
325
510
570
820
905
1230
1350
1750
1960
2460
2730
3230
3680
12
14
25
27
44
49
70
78
105
120
155
170
210
240
375
420
605
670
910
995
1290
1440
1820
2010
2380
2710
1
2
4
7
17
18
33
39
58
60
90
92
99
145
155
195
220
280
310
480
525
960
1060
1730
1880
3
5
12
13
24
29
42
44
66
68
73
105
115
145
165
205
230
355
390
705
785
1270
1380
6
11
26
28
52
61
91
95
105
145
155
225
240
310
350
440
650
760
830
1510
1680
2650
2960
5
8
19
21
39
45
67
70
77
105
115
165
180
230
260
325
480
560
610
1120
1240
1950
2190
9
15
36
39
72
85
125
130
145
200
l215
315
335
405
485
610
900
1050
1150
2100
2320
3660
4100
7
11
27
29
53
62
93
97
105
150
160
230
245
300
355
450
665
780
845
1550
1710
2700
3220
in-tpi = nominal threadia. in inches-threads per inch
N· m = newton-meters
3 ft-lb= foot pounds
1 1/2" - 6
1180 870
2640 1950 4290 3160
4 mm x pitch = nominal thread diameter in millimeters x
1 1/2" - 12
1330 980
2970 2190 4820 3560
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
Tire Inflation Chart
Tire Size
10 x 4 Saw Tooth
10/11/06
Inflation
PSI
50
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
23
Table of Contents
Land Pride
Section 8: Appendix
Warranty
Land Pride warrants to the original purchaser that this Land Pride product will
be free from defects in material and workmanship for a period of one year, from
the date of delivery to the end user, when used as intended and under normal
service and conditions for personal use; and 6 months for municipalities, golf
courses, sod farms and rental purposes. This Warranty is limited to the
replacement of any defective part by Land Pride and the installation by the dealer
of any such replacement part, and does not cover common wear items such as
blades, belts, tines, etc. Land Pride reserves the right to inspect any equipment or
parts which are claimed to have been defective in material or workmanship.
This Warranty does not apply to any part or product which in Land Pride’s
judgment shall have been misused or damaged by accident or lack of normal
maintenance or care, or which has been repaired or altered in a way which
adversely affects its performance or reliability, or which has been used for a
purpose for which the product is not designed. Misuse also specifically includes
failure to properly maintain oil levels, grease points, and driveline shafts.
Claims under this Warranty must be made to the dealer which originally sold
the product and all warranty adjustments must be made through such dealer. Land
Pride reserves the right to make changes in materials or design of the product at
any time without notice.
This Warranty shall not be interpreted to render Land Pride liable for damages
of any kind, direct, consequential, or contingent to property. Furthermore, Land
Pride shall not be liable for damages resulting from any cause beyond its
reasonable control. This Warranty does not extend to loss of crops, any expense
or loss for labor, supplies, rental machinery or for any other reason.
No other warranty of any kind whatsoever, express or implied, is made
with respect to this sale; and all implied warranties of merchantability and
fitness for a particular purpose which exceed the obligations set forth in this
written warranty are hereby disclaimed and excluded from this sale.
This Warranty is not valid unless registered with Land Pride within 30 days from
the date of delivery to the end user.
In addition to the Standard Limited Warranty Land Pride also provides:
A Five - Year Limited Warranty on Gearbox Components, on RC6015,
RCM6015, RC5015, RCM5015, RC5010, RCM5010, PD15, PD25, and PD35. A
Three - Year Limited Warranty on Gearbox Components on RCR3596, RCR3510,
and RCRM3510, provided they have been properly maintained, and not subjected
to misuse or abuse. Misuse specifically includes, but is not limited to, maintaining
proper oil levels of the correct lubricant, and adjusting slip-clutches to provide
proper protection to Gearbox Components. Warranty is One Year for seals. Seals
are viewed as normal wear items and replacement will be the customer’s
responsibility. Gearboxes will either be replaced or rebuilt at Land Pride’s
discretion.
24
FD2560, FD2572, AT2560 & AT2572 Grooming Mower, 3-spindle 310-148M
10/11/06
Corporate Office: P.O. Box 5060
Salina, Kansas 67402-5060 USA
www.landpride.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Producer : Acrobat Distiller 4.05 for Sparc Solaris Creator : FrameMaker 6.0 Modify Date : 2008:05:08 14:10:13 Create Date : 1993:11:17 08:21:15 Page Count : 27 Page Mode : UseOutlinesEXIF Metadata provided by EXIF.tools