Lantronix Network Router 2100E Users Manual WiBox 6.6 User Guide

2015-02-09

• WiBox 2100E Device Server User Guide
  • Intellectual Property
  • Warranty
  • Contacts
  • Revision History
  • Table of Contents
  • List of Tables
  • List of Figures
• 1: Using This Guide
  • Purpose and Audience
  • Chapter Summary
  • Additional Documentation
• 2: Introduction
  • Applications
  • Application Examples
    • Serial Tunneling – Network
    • Ad Hoc Network
    • Serial Tunneling – Infrastructure
    • Ad Hoc WiBox 2100E Connection
    • WiBox 2100E with Ethernet
  • Protocol Support
  • Configuration Methods
  • Addresses and Port Numbers
    • Hardware Address
    • IP Address
    • WLAN Settings
    • Port Numbers
  • Serial Connector Pinouts
  • WiBox 2100E Network Interface
    • Ethernet Connector Pinouts
  • LEDs
  • Technical Specifications
• 3: Getting Started
  • Installing the WiBox 2100E
  • Configuring the WiBox 2100E
  • Installing DeviceInstaller
  • Viewing the Current Configuration
• 4: Web Manager Configuration
  • Accessing Web Manager through a Web Browser
  • Network Configuration
    • Network Mode Configuration
    • Automatic IP Address Configuration
    • Static IP Address Configuration
    • Ethernet Configuration
  • Server Configuration
    • Server Configuration
    • Advanced
  • Hostlist Configuration
    • Retry Settings
    • Host Information
  • Channel 1 and Channel 2 Configuration
    • Serial Settings
      • Channel
      • Port Settings
      • Pack Control
      • Flush Input Buffer (Serial to Network)
      • Flush Output Buffer (Network to Serial)
    • Connection Settings - TCP
      • Connect Protocol
      • Connect Mode: Passive Connection
      • Connect Mode: Active Connection
      • Endpoint Configuration
      • Common Options
      • Disconnect Mode
    • Connection Settings - UDP
      • Connect Protocol
      • Datagram Mode
      • Endpoint Configuration
  • WLAN Configuration
    • Wireless Network Configuration
    • Wireless Network Security
    • WEP Options
    • WPA Options
    • 802.11i/WPA2-Personal Options
    • Advanced Settings
  • Updating Settings
  • Applying Defaults
• 5: Telnet or Serial Port (Setup Mode) Configuration
  • Accessing Setup Mode
    • Telnet Connection
    • Serial Port Connection
  • Exiting Setup Mode
• 6: Setup Mode: Server Configuration
  • Server Configuration (Option 0)
    • Network Mode
  • IP Address
  • Set Gateway IP Address
  • Netmask: Number of Bits for Host Part
  • Set DNS Server IP Address
  • Change Telnet Configuration Password
    • Automatic Host MAC Detection
  • DHCP Name
• 7: Setup Mode: Channel Configuration
  • Channel 1 (Option 1)
  • Baudrate
  • I/F (Interface) Mode
  • Flow
  • Port Number
  • Connect Mode
    • a) Incoming Connection
    • b) Response
    • c) Active Startup
    • d) Datagram Type
    • e) Modem Mode
  • Send the Escape Sequence (+++) in Modem Mode
  • Show IP addr after 'RING'
  • Auto Increment Source Port
  • Remote IP Address
  • Remote Port
  • DisConnMode
  • Flush Mode (Buffer Flushing)
  • Pack Control
    • Packing Interval
    • Trailing Characters
    • Send Characters
  • DisConnTime (Inactivity Timeout)
  • Send Characters
  • Telnet Terminal Type
  • Channel (Port) Password
  • WLAN Settings
    • Topology
    • Network Name (SSID)
    • Adhoc Network Channel
    • Security Suite
    • WEP
    • WPA
    • 802.11i/WPA2-Personal
    • Fixed or Automatic Data Rate
    • Transmission Data Rate
    • Minimum TX Data Rate
    • Enable Power Management
    • Enable Soft AP Roaming
    • Max TX Failures
• 8: Setup Mode: Advanced Settings
  • Expert Settings (Option 5)
    • TCP Keepalive time in seconds
    • ARP Cache timeout in seconds
    • CPU Performance
    • Disable Monitor Mode at bootup
    • HTTP Port Number
    • MTU Size
    • TCP Re-transmission Timeout
    • Enable Alternate MAC
    • Ethernet Connection Type
    • Configurable Server Port Number
    • Automatic Host MAC Detection
  • Security Settings (Option 6)
    • Disable SNMP
    • SNMP Community Name
    • Disable Telnet Setup
    • Disable TFTP Firmware Upgrade
    • Disable Port 77FE (Hex)
    • Disable Web Server
    • Disable Web Setup
    • Disable ECHO Ports
    • Enable Encryption
    • Enable Encryption
    • Enable Enhanced Password
  • Default Settings (Option 7)
    • Channel 1 Configuration
    • Channel 2 Configuration
    • WLAN Settings
    • Expert Settings
    • Security Settings
  • Exit Configuration Mode
• 9: Monitor Mode
  • Entering Monitor Mode via the Serial Port
  • Entering Monitor Mode via the Network Port
  • Monitor Mode Commands
• 10: Updating Firmware
  • Obtaining Firmware
  • Reloading Firmware
  • Recovering the Firmware Using the Serial Port and DeviceInstaller
  • WLAN Country Setting
• 11: Wireless Bridging
  • Configuring the WiBox 2100E in Bridging Mode
    • Method 1
    • Method 2
    • Method 3
• 12: Troubleshooting
  • Diagnostic LED States
  • Problems and Error Messages
  • Technical Support
• A: Mounting Brackets
• B: Binary to Hexadecimal Conversions
  • XE "Binary to hexadecimal conversions" Converting Binary to Hexadecimal
    • Conversion Table
    • Scientific Calculator
• C: Compliance
  • Compliance Information
  • Regulatory Information
    • USA Federal Communications Commission (FCC) Notice
    • Canada – Industry Canada Notice
      • Antenna Notice:
      • Exposure of Humans to RF Fields
    • Europe – R&TTE Directive 99/5/EC, Wireless Notice
    • Australia & New Zealand – Wireless Notice