Launch Tech CRP429 Professional Diagnostic Tool User Manual 15 CRP429 UserMan

Launch Tech Co., Ltd. Professional Diagnostic Tool 15 CRP429 UserMan

15_CRP429 UserMan

User ManualLAUNCHStatement: LAUNCH owns the complete intellectual property rights for the software used by this product. For any reverse engineering or cracking actions against the software, LAUNCH will block the use of this product and reserve the right to pursue their legal liabilities.Professional Diagnostic ToolCRP429Launch Tech Co., Ltd.
iLAUNCH CRP429 User's ManualENTrademark InformationLAUNCH is a registered trademark of LAUNCH TECH CO., LTD. (LAUNCH) in China and other countries. All other LAUNCH trademarks, service marks, domain names, logos and company names referred to in this manual are either trademarks, registered trademarks, service marks, domain names, logos and company names of or are otherwise the property of LAUNCH or its afliates. In countries where any of the LAUNCH trademarks, service marks, domain names, logos and company names are not registered, LAUNCH claims other rights associated with unregistered trademarks, service marks, domain names, logos and company names. Other products or company names referred to in this manual may be trademarks of their respective owners. You may not use any trademark, service mark, domain name, logo, or company name of LAUNCH or any third party without permission from the owner of the applicable trademark, service mark, domain name, logo, or company name. You may contact LAUNCH by visiting the website at www.cnlaunch.com, or writing to LAUNCH TECH. CO., LTD., Launch Industrial Park, North of Wuhe Avenue, Banxuegang, Bantian, Longgang, Shenzhen, Guangdong, P.R.China, to request written permission to use Materials on this manual for purposes or for all other questions relating to this manual.Copyright InformationCopyright © 2018 by LAUNCH TECH. CO., LTD. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying and recording or otherwise, without the prior written permission of LAUNCH. The information contained herein is designed only for the use of this unit. LAUNCH is not responsible for any use of this information as applied to other units.
iiLAUNCH CRP429 User's ManualGeneral Notice•Other product names used herein are for identification purposes only andmay be trademarks of their respective owners. LAUNCH disclaims any and all rights in those marks. •There is a possibility that this unit is inapplicable to some of the vehiclemodels or systems listed in the diagnosis section due to different countries, areas, and/or years. Do not hesitate to contact LAUNCH if you come across such questions. We are to help you solve the problem as soon as possible.Disclaimer•To take full advantage of the unit, you should be familiar with the engine.•All information, illustrations, and specications contained in this manual arebased on the latest information available at the time of publication. The rightis reserved to make change at any time without notice.• Neither LAUNCH nor its afliates shall be liable to the purchaser of this unitor third parties for damages, losses, costs or expenses incurred by purchaseror third parties as a result of: accident, misuse, or abuse of this unit, orunauthorized modifications, repairs, or alterations to this unit, or failure tostrictly comply with LAUNCH operating and maintenance instructions.•LAUNCH shall not be liable for any damages or problems arising from theuse of any options or any consumable products other than those designatedas Original LAUNCH Products or LAUNCH Approved Products by LAUNCH.Safety Precautions and WarningsTo prevent personal injury or damage to vehicles and/or the CRP429, please read this user’s manual first carefully and observe the following safety precautions at a minimum whenever working on a vehicle:•Always perform automotive testing in a safe environment.•Do not attempt to operate or observe the tool while driving a vehicle.Operating or observing the tool will cause driver distraction and could cause afatal accident.• Wear safety eye protection that meets ANSI standards.•Keep clothing, hair, hands, tools, test equipment, etc. away from all moving orhot engine parts.•Operate the vehicle in a well-ventilated work area: Exhaust gases arepoisonous.•Put blocks in front of the drive wheels and never leave the vehicle unattendedwhile running tests.
iiiLAUNCH CRP429 User's ManualEN•Use extreme caution when working around the ignition coil, distributor cap,ignition wires and spark plugs. These components create hazardous voltageswhen the engine is running.•Put the transmission in P (for A/T) or N (for M/T) and make sure the parkingbrake is engaged.• Keep a re extinguisher suitable for gasoline/chemical/ electrical res nearby.•Don’t connect or disconnect any test equipment while the ignition is on or theengine is running.•Keep the CRP429 dry, clean, free from oil/water or grease. Use a milddetergent on a clean cloth to clean the outside of the CRP429, whennecessary.•Please use the DC 5V power adaptor to charge the CRP429. No responsibilitycan be assumed for any damage or loss caused as a result of using poweradaptors other than the right one.Warning:This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.The device has been evaluated to meet general RF exposure requirement. The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types Professional Diagnostic Tool with model CRP429 has also been tested against this SAR limit. The highest reported SAR values for body-worn is 1.25 W/kg. This device was tested for typical body-worn operations with the back of the handset kept 0mm from the body. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided.
ivLAUNCH CRP429 User's ManualTable of Contents1. Introduction ............................................................................................. 12. General Information ............................................................................... 22.1 On-Board Diagnostics (OBD) II ..................................................................... 22.2 Diagnostic Trouble Codes (DTCs) ................................................................. 22.3 Location of the Data Link Connector (DLC)................................................... 32.4 OBD II Readiness Monitors ........................................................................... 42.5 OBD II Monitor Readiness Status.................................................................. 52.6 OBD II Denitions .......................................................................................... 53. Product Descriptions ............................................................................. 73.1 Outline of CRP429......................................................................................... 73.2 Technical Specications ................................................................................ 93.3 Accessories Checklist .................................................................................... 94. Initial Use............................................................................................... 104.1 Charging CRP429 ....................................................................................... 104.2 Getting Started ............................................................................................ 104.3 Job Menu ..................................................................................................... 125. Diagnose ............................................................................................... 145.1 Connection .................................................................................................. 145.2 System Diagnosing...................................................................................... 145.2.1 Smart Diagnosis (Auto-Detect) ............................................................ 145.2.2 Manual Diagnosis ................................................................................ 165.3 OBDII Diagnosis .......................................................................................... 235.4 History ......................................................................................................... 265.5 Resetting ..................................................................................................... 276. Update ................................................................................................... 287. Data ........................................................................................................ 297.1 Diagnostic Record ....................................................................................... 297.2 Diagnostic Report ........................................................................................ 307.3 DTC Library ................................................................................................. 307.4 DLC(Data Link Connector) Location............................................................ 317.5 Image........................................................................................................... 31
vLAUNCH CRP429 User's ManualEN7.6 Feedback ..................................................................................................... 317.7 Firmware Fix ................................................................................................ 317.8 User Manual ................................................................................................ 318. Settings ................................................................................................. 328.1 Units of measurement ................................................................................. 328.2 Automatic detection on connect................................................................... 328.3 Display & Brightness ................................................................................... 328.4 Sound .......................................................................................................... 328.5 Network ....................................................................................................... 328.6 Date/Time .................................................................................................... 328.7 Language..................................................................................................... 328.8 Email Setup ................................................................................................. 338.9 Recovery ..................................................................................................... 338.10 Version....................................................................................................... 338.11 About .......................................................................................................... 339. FAQ ........................................................................................................ 34
1LAUNCH CRP429 User's ManualEN1. IntroductionCRP429 is an evolutionary smart solution for passenger car diagnosis. It inherits from LAUNCH’s advanced diagnosing technology and is characterized by covering a wide range of vehicles, featuring powerful functions, and providing precise test result.CRP429 has the following functions and advantages:•Smart(Auto-Detect) Diagnosis: Once CRP429 and the vehicle are properlyconnected, the system starts auto-detect process. Once the whole process is successfully nished, a diagnostic report will be automatically generated and sent to your email box (if bound). •Manual Diagnosis: If Auto-Detect failure occurs, manual diagnosis is alsoavailable. Diagnosis functions include: Version Information, Read DTCs, Clear DTCs and Read Data Stream (supports 3 display modes: Value, Graph and Merged).•OBDII/EOBD Diagnosis: 10 modes of OBD II test are supported, includingEVAP, O2 Sensor, I/M Readiness, MIL Status, VIN Info, and On-boardmonitors testing etc.•Remote Diagnosis (optional): This option aims to help repair shops ortechnicians launch instant messaging and remote diagnosis, making therepair job getting xed faster.•Reset: Frequently used maintenance and reset items including Oil lamp reset,DPF regeneration, Electronic parking brake reset, Steering angle calibration,IMMO service, Battery maintenance system reset, ABS bleeding and Injectorcoding can be done.•One-click Update: Let you update your diagnostic software and APK online.•Diagnostic History: This function provides a quick access to the testedvehicles and users can choose to view the test report or resume from the lastoperation, without the necessity of starting from scratch.•Diagnostic Feedback: Use this option to submit the vehicle issue to us foranalysis and troubleshooting.•DTC Library: Allows you to retrieve the definition of the diagnostic troublecode from the abundant DTC database.•Displays battery real-time voltage once properly connected to the vehicle.•Features screenshot capture. Screenshots and reports sharing are supported.•Touch & Keypad input are supported. Quick Dial buttons enables you to easilyaccess the corresponding functions.
2LAUNCH CRP429 User's Manual2. General Information2.1 On-Board Diagnostics (OBD) IIThe first generation of On-Board Diagnostics (OBD I) was developed by the California Air Resources Board (ARB) and implemented in 1988 to monitor some of the emission control components on vehicles. As technology evolved and the desire to improve the On-Board Diagnostic system increased, a new generation of On-Board Diagnostic system was developed. This second generation of On-Board Diagnostic regulations is called “OBD II”. The OBD II system is designed to monitor emission control systems and key engine components by performing either continuous or periodic tests of specic components and vehicle conditions. When a problem is detected, the OBD II system turns on a warning lamp (MIL) on the vehicle instrument panel to alert the driver typically by the phrase of “Check Engine” or “Service Engine Soon”. The system will also store important information about the detected malfunction so that a technician can accurately nd and x the problem. Here below follow three pieces of such valuable information:1) Whether the Malfunction Indicator Light (MIL) is commanded ‘on’ or ‘off’;2) Which, if any, Diagnostic Trouble Codes (DTCs) are stored;3) Readiness Monitor status.2.2 Diagnostic Trouble Codes (DTCs)OBD II Diagnostic Trouble Codes are codes that are stored by the on-board computer diagnostic system in response to a problem found in the vehicle. These codes identify a particular problem area and are intended to provide you with a guide as to where a fault might be occurring within a vehicle. OBD II Diagnostic Trouble Codes consist of a five-digit alphanumeric code. The first character, a letter, identifies which control system sets the code. The second character, a number, 0-3; other three characters, a hex character, 0-9 or A-F provide additional information on where the DTC originated and the operating conditions that caused it to set. Here below is an example to illustrate the structure of the digits:
3LAUNCH CRP429 User's ManualENFigure 2-12.3 Location of the Data Link Connector (DLC)The DLC (Data Link Connector or Diagnostic Link Connector) is typically a 16-pin connector where diagnostic code readers interface with the vehicle’s on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver’s side for most vehicles. If Data Link Connector is not located under dashboard, a label should be there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access the connector. If the DLC cannot be found, refer to the vehicle’s service manual for the location.
4LAUNCH CRP429 User's ManualFigure 2-22.4 OBD II Readiness MonitorsAn important part of a vehicle’s OBD II system is the Readiness Monitors, which are indicators used to find out if all of the emissions components have been evaluated by the OBD II system. They are running periodic tests on specific systems and components to ensure that they are performing within allowable limits.Currently, there are eleven OBD II Readiness Monitors (or I/M Monitors) dened by the U.S. Environmental Protection Agency (EPA). Not all monitors are supported in every vehicles and the exact number of monitors in any vehicle depends on the motor vehicle manufacturer’s emissions control strategy.Continuous Monitors -- Some of the vehicle components or systems are continuously tested by the vehicle’s OBD II system, while others are tested only under specific vehicle operating conditions. The continuously monitored components listed below are always ready:1. Misre2. Fuel System3. Comprehensive Components (CCM)Once the vehicle is running, the OBD II system is continuously checking the above components, monitoring key engine sensors, watching for engine misre, and monitoring fuel demands. Non-Continuous Monitors -- Unlike the continuous monitors, many emissions and engine system components require the vehicle to be operated under specic conditions before the monitor is ready. These monitors are termed non-continuous monitors and are listed below:1) EGR System2) O2 Sensors3) Catalyst4) Evaporative System5) O2 Sensor Heater
5LAUNCH CRP429 User's ManualEN6) Secondary air Injection7) Heated Catalyst8) A/C system2.5 OBD II Monitor Readiness StatusOBD II systems must indicate whether or not the vehicle’s PCM’s monitor system has completed testing on each component. Components that have been tested will be reported as “Ready”, or “Complete”, meaning they have been tested by the OBD II system. The purpose of recording readiness status is to allow inspectors to determine if the vehicle’s OBD II system has tested all the components and/or systems.The Powertrain Control Module (PCM) sets a monitor to “Ready” or “Complete” after an appropriate drive cycle has been performed. The drive cycle that enables a monitor and sets readiness codes to “Ready” varies for each individual monitor. Once a monitor is set as “Ready” or “Complete”, it will remain in this state. A number of factors, including erasing of Diagnostic Trouble Codes (DTCs) with a code reader or a disconnected battery, can result in Readiness Monitors being set to “Not Ready”. Since the three continuous monitors are constantly evaluating, they will be reported as “Ready” all of the time. If testing of a particular supported non-continuous monitor has not been completed, the monitor status will be reported as “Not Complete” or “Not Ready.”In order for the OBD monitor system to become ready, the vehicle should be driven under a variety of normal operating conditions. These operating conditions may include a mix of highway driving and stop and go, city type driving, and at least one overnight-off period. For specic information on getting your vehicle’s OBD monitor system ready, please consult your vehicle owner’s manual.2.6 OBD II DenitionsPowertrain Control Module (PCM) -- OBD II terminology for the on-board computer that controls engine and drive train.Malfunction Indicator Light (MIL) -- Malfunction Indicator Light (Service Engine Soon, Check Engine) is a term used for the light on the instrument panel. It is to alert the driver and/or the repair technician that there is a problem with one or more of vehicle’s systems and may cause emissions to exceed federal standards. If the MIL illuminates with a steady light, it indicates that a problem has been detected and the vehicle should be serviced as soon as possible. Under certain conditions, the dashboard light will blink or ash. This indicates a severe problem and flashing is intended to discourage vehicle operation. The vehicle onboard diagnostic system cannot turn the MIL off until the necessary repairs are completed or the condition no longer exists.
6LAUNCH CRP429 User's ManualDTC -- Diagnostic Trouble Codes (DTC) that identifies which section of the emission control system has malfunctioned.Enabling Criteria -- Also termed Enabling Conditions. They are the vehicle-specic events or conditions that must occur within the engine before the various monitors will set, or run. Some monitors require the vehicle to follow a prescribed “drive cycle” routine as part of the enabling criteria. Drive cycles vary among vehicles and for each monitor in any particular vehicle. Please refer to the vehicle’s factory service manual for specic enabling procedures.OBD II Drive Cycle -- A specific mode of vehicle operation that provides conditions required to set all the readiness monitors applicable to the vehicle to the “ready” condition. The purpose of completing an OBD II drive cycle is to force the vehicle to run its onboard diagnostics. Some form of a drive cycle needs to be performed after DTCs have been erased from the PCM’s memory or after the battery has been disconnected. Running through a vehicle’s complete drive cycle will “set” the readiness monitors so that future faults can be detected. Drive cycles vary depending on the vehicle and the monitor that needs to be reset. For vehicle specic drive cycle, consult the service manual.Freeze Frame Data -- When an emissions related fault occurs, the OBD II system not only sets a code but also records a snapshot of the vehicle operating parameters to help in identifying the problem. This set of values is referred to as Freeze Frame Data and may include important engine parameters such as engine RPM, vehicle speed, air ow, engine load, fuel pressure, fuel trim value, engine coolant temperature, ignition timing advance, or closed loop status.Fuel Trim (FT) - Feedback adjustments to the base fuel schedule. Short-term fuel trim refers to dynamic or instantaneous adjustments. Long-term fuel trim refers to much more gradual adjustments to the fuel calibration schedule than short-term trim adjustments. These long-term adjustments compensate for vehicle differences and gradual changes that occur over time.
7LAUNCH CRP429 User's ManualEN3. Product Descriptions3.1 Outline of CRP429Figure 3-1No. Name Descriptions1LCD Indicates test results.2I/M A quick dial to Read I/M readiness. *Note: This funcon only applies to Diagnose.
8LAUNCH CRP429 User's Manual3 Auto VIN DetectPress it to quickly launch the auto VIN detection module.*Note: To detect more and accurate VINs, a stable network connecon is highly recommened for this funcon.4 UpdateA quick access to the Update module. *Note: This funcon requires a stable network connecon.5 Return Exit the current program or return to the previous screen. 6 HOME Press to the home(Job menu) screen.7/Move cursor up and down for selection./Move cursor left or right for selection; Or turn page up and down when more than one page is displayed.8OBD-16 connectorTo connect to vehicle's DLC (Data Link Connector) via diagnostic cable.95V Charging port To connect to external DC power for charging CRP429. 10 Power• In Off mode, press it for about 5 seconds to turnthe handset on.• In On mode:•Press it to activate the LCD if the LCD is off.•Press it to turn off the LCD if the LCD lightsup.•Press it for 3 seconds to turn it off.11 OK Conrms a selection (or action) from a menu list.12 ScreenshotsPress it once to capture the current screen. All screenshots are saved in the “Image” folder of “Data”.13 Diagnostic ReportsA quick dial to the “Diagnostic Reports” module. Alternatively, it can also be accessed by “Data” -> “Diagnostic Report”.
9LAUNCH CRP429 User's ManualEN14 Help Provides detailed descriptions/tips for diagnostics.15 Charging LED Red means Charging and Green means Fully charged.3.2 Technical Specications• Screen: 5” IPS touch screen•RAM: 1G•ROM: 8GB•Battery: 4000mAh rechargeable Li-battery• OBDII input voltage range: 9~18V•Touch & Keypad input•Charging via:•DC 5V charging cable or•Diagnostic cable through connection to vehicle’s DLC•Dimension: 248.7mm x 93.5mm x 36mm•Net weight: 530g•Working temperature: -10 to 50°C (14 to 122 F°)•Storage temperature: -20 to 70°C (-4 to 158 F°)3.3 Accessories ChecklistFor detailed accessory items, please consult from the local agency or check the packing list supplied with CRP429 together.1. CRP429 handset2. OBD II diagnostic cable3. DC 5V charging cable4. User manual5. Padded carrying case
10LAUNCH CRP429 User's Manual4. Initial Use4.1 Charging CRP429There are two charging methods available:Via Charging Cable: Plug one end of the included charging cable into the DC-IN port of the tool, and the other end to the external DC power.Via Diagnostic Cable: Insert one end of the diagnostic cable into the DB-15 connector of the tool, and the other end to the vehicle’s DLC.Once the charging LED illuminates solid green, it indicates that the battery is fully charged.4.2 Getting StartedIf it is the first time you have used this tool, you need to make some system settings.1. Press the [Power] button to power it on.2. The screen displays a welcome page. Tap “Start” to go to next step.Figure 4-1
11LAUNCH CRP429 User's ManualEN3. Choose the desired system language, and tap “Next”.4. Choose the desired time zone, and tap “Next” to enter the WLAN setup page.5. Slide the switch to ON, the system starts searching for all available wirelessLANs. Choose the desired WLAN access point / network,• If the network you chose is open, you can connect directly;•If the selected network is encrypted, you have to enter the right securitykey (network password).*Note: If you choose “Ignore” in WLAN setup, it will go into the date seng page. If the tool has been properly connected to the Internet, the system will automacally obtain the correct network date and me and navigate to step 6. 6. After the network connection is done, tap “Next” to congure email address.Input the email address, and tap “Next” to navigate to the Job menu.Figure 4-2*Note: You are strongly recommended to fill in the valid email address. Once youcongured this opon, the system will automacally send the diagnosc report to your email box every me a complete Auto-Detect process is successfully nished.
12LAUNCH CRP429 User's Manual4.3 Job MenuIt mainly includes the following function modules.Figure 4-3Diagnose To congures CRP429 to operate as a diagnostic tool.OBD IIThis option presents a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related.Reset To perform common repair & maintenance items, including ABS bleeding, DPF regeneration and oil lamp reset etc. Update To update vehicle diagnostic software and APK.*Note: This function requires a stable network connection.
13LAUNCH CRP429 User's ManualENData Includes Diagnostic report, Diagnostic record, Feedback and Image etc.Settings To make some system settings, including Network setup, Email and Brightness etc.GEAR+(Coming soon)An add-on module for function extension, including Promotion message pushing and Software subscription etc.
14LAUNCH CRP429 User's Manual5. Diagnose5.1 Connection1. Turn the ignition off.2. Locate vehicle’s DLC socket: It provides standard 16 pins and is generallylocated on driver’s side, about 12 inches away from the center of dashboard.See Figure 2-2. If DLC is not equipped under dashboard, a label indicatingits position will be given. In case no DLC is found, please refer to AutomobileRepair Manual.3. Plug one end of the diagnostic cable into the DB-15 connector of CRP429,and tighten the captive screws. Connect the other end to the vehicle’s DLC.Diagnostic CableCRP429Vehicle's DLCFigure 5-15.2 System DiagnosingThis function is specially designed to diagnose electronic control systems of single vehicle model.5.2.1 Smart Diagnosis (Auto-Detect)After connection, turn the ignition key on and the system enters auto-detect
15LAUNCH CRP429 User's ManualENmode. *Note: To detect more and accurate VINs, a stable network connection is highlyrecommended for this funcon.*CAUTION: Don’t connect or disconnect any test equipment with ignion on or engine running.A. Once the system successfully obtains the VIN (Vehicle Identication Number) information of the currently identified vehicle, it will continue scanning the vehicle systems. After the scanning is complete, a diagnostic report will be automatically generated and sent to your email box (if bound). B. If the tool failed to access the VIN information, the screen will display as below:Fig. 5-2Input the VIN, and tap “OK”, the system will automatically identify the vehicle model. If the vehicle VIN is successfully decoded, it will perform auto-diagnosis until a diagnostic report is automatically output. Otherwise it will enter manual diagnosis mode. For details on manual diagnosis, see Chapter 5.2.2.*Notes: • The most recognizable location for this number is in the top left corner on the vehicle’s dashboard. Other locations include the driver’s door or post, and therewall under the hood. • In general, vehicle identification numbers are standardized - all contain 17
16LAUNCH CRP429 User's Manualcharacters. VIN characters may be capital letters A through Z and numbers 1 through 0; however, the letters I, O and Q are never used in order to avoid mistakes of misreading. No signs or spaces are allowed in the VIN. 5.2.2 Manual DiagnosisIf the tool can not obtain the VIN information, you can also perform vehicle diagnosis manually. In this mode, you need to execute the menu-driven command and then follow the on-screen instruction to proceed. *Notes: • Before diagnosing, please make sure the diagnosc program corresponding to certain vehicle model has been installed on your CRP429. • For vehicles manufactured by different vendors, it is possible that it has differentdiagnosc menus. For details, please follow the instrucons on the screen to proceed.Refer to the owchart illustrated as below to diagnose a vehicle manually:Select “Diagnose”Automatic(Note: This mode allows your tool to scan the vehicle test system automatically)Manual Select(Note: In this case, you need to choose the desired system manually. Just follow the on-screen instructions to proceed.)Select test systemSelect test functionSelect Vehicle Model(Note: For different vehicles, vehicle make selection may differ. Generally, we can choose a vehicle via make year. But for BENZ, we need to choose it via chassis.)Select Vehicle ManufacturerRead versioninformationRead fault codeClear fault codeRead data streamTake Demo as an example to demonstrate how to diagnose a vehicle.
17LAUNCH CRP429 User's ManualEN1). Select diagnostic software version: Tap the “DEMO” to go to Step 2.Fig. 5-3 Fig. 5-42). Select test item: Select the desired test item to proceed. Fig. 5-55.2.2.1 Health Report (Quick Test)This function varies from vehicle to vehicle. It enables you to quickly access all the electronic control units of the vehicle and generate a detailed report about vehicle health.Tap “Health Report”, the system starts scanning the ECUs. Once the scanning is
18LAUNCH CRP429 User's Manualcomplete, a screen similar to the following appears:Fig. 5-6In above gure, the tested system with fault code appears in red and the system with OK displays in white (normally).On-screen Buttons:: Tap to display the details of DTCs existing in the current system. Tap to hide it.Enter: Tap to select other test functions. For detailed operations, refer to Chapter 5.2.2.3 “System Selection”.Report: Tap to save the diagnostic result as a report.Clear DTC: Tap to clear the existing diagnostic trouble codes.5.2.2.2 System ScanThis option allows you to quickly scan which systems are installed on the vehicle.5.2.2.3 System SelectionThis option allows you manually select the test system and function step by step.In Fig. 5-5, tap “System Selection”, the screen displays as follows:
19LAUNCH CRP429 User's ManualENFig. 5-7Tap the desired system (take “ECM” for example) to jump to the test function page.Fig. 5-8*Note: Dierent vehicle has dierent diagnosc menus.A. Version InformationThis function is used to read the version information of system mode, vehicle VIN, software and ECU.B. Read Fault CodeThis function displays the detailed information of DTC records retrieved from the vehicle’s control system.In Fig. 5-8, tap “Read DTC”, the screen will display the diagnostic result.
20LAUNCH CRP429 User's ManualFig. 5-9On-screen Buttons:Freeze Frame: When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data. Freeze frame data includes a snapshot of critical parameter values at the time the DTC is set.Help: Tap to view the help information.Code Search: Tap it to search for more information about the current DTC online.Report: To save the current data in text format. All diagnostic reports can be accessed from “Data” -> “Diagnostic Report”.C. Clear Fault MemoryAfter reading the retrieved codes from the vehicle and certain repairs have been carried out, you can use this function to erase the codes from the vehicle. Before performing this function, please be sure the vehicle’s ignition key is in the ON position with the engine off.*Note: The trouble code will not disappear unl the trouble was completely cleared.D. Read Data Stream
21LAUNCH CRP429 User's ManualENThis option retrieves and displays live data and parameters from the vehicle’s ECU.In Fig. 5-8, tap “Read Data Stream”, the system will display data stream items. Fig. 5-10On-screen Buttons:Select All: Tap it to select all items of the current page. To select certain data stream item, just check the box before the item name.Unselect: Tap it to deselect all data stream items.OK: Tap it to conrm and jump to the next step.After selecting the desired items, tap “OK” to enter the data stream reading page.
22LAUNCH CRP429 User's ManualFig. 5-11*Notes: 1. If the value of the data stream item is out of the range of the standard (reference)value, the whole line will display in red. If it complies with the reference value, it displays in blue (normal mode).2. The indicator 1/X shown on the boom of the screen stands for the current page/total page number. Swipe the screen from the right/left to advance/return to the next/previous page. There are 3 types of display modes available for data viewing, allowing you to view various types of parameters in the most suitable way. •Value – this is the default mode which displays the parameters in texts andshows in list format. •Graph – displays the parameters in waveform graphs.•Combine – this option is mostly used in graph merge status for datacomparison. In this case, different items are marked in different colors.On-screen Buttons:: Tap it to view the waveform graph of the current data stream item.
23LAUNCH CRP429 User's ManualENFig. 5-12Combine: Tap it, a pull-down list of the data stream items appears on the screen. Select the necessary items and the screen will display the waveforms corresponding to these items immediately.Report: To save the current data as a diagnostic report. All diagnostic reports can be accessed from “Data” -> “Diagnostic Report”.Record: Tap to start recording diagnostic data for future playback and analysis. The saved le follows the naming rule: It begins with vehicle type, and then the record starting time and ends with .x431 (To differentiate between les, please congure the accurate system time). All diagnostic records can be replayed from “Data” -> “Diagnostic Record”.5.3 OBDII DiagnosisThis option presents a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related.On the Job menu, press [OBD II] to enter system, the screen will automatically jump to gure 5-13:
24LAUNCH CRP429 User's ManualFigure 5-13 Figure 5-14Tap [OK], a screen similar to Figure 5-14 will appear.It mainly includes the following functions:1. Read CodesThis option is used to identify which section of the emission control system has malfunctioned.2. Erase CodesAfter reading the retrieved codes from the vehicle and certain repairs have been carried out, you can use this function to erase the codes from the vehicle. Before performing this function, please be sure the vehicle’s ignition key is in the ON position with the engine off.*Notes:• Before performing this funcon, make sure to retrieve and record the trouble codes.• After clearing, you should retrieve trouble codes once more or turn ignition onand retrieve codes again. If there are sll some trouble codes in the system, please troubleshoot the code using a factory diagnosis guide, then clear the code andrecheck.
25LAUNCH CRP429 User's ManualEN3. I/M ReadinessI/M refers to Inspection and Maintenance that is legislated by the Government to meet federal clean-air standards. I/M Readiness indicates whether or not the various emissions-related systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing.The purpose of the I/M Readiness Monitor Status is to indicate which of the vehicle’s Monitors have run and completed their diagnosis and testing (as described in Chapter 2.5), and which ones have not yet run and completed testing and diagnosis of their designated sections of the vehicle’s emissions system.The I/M Readiness Monitor Status function also can be used (after repair of a fault has been performed) to confirm that the repair has been performed correctly, and/or to check for Monitor Run Status.4. Data StreamThis option retrieves and displays live data and parameters from the vehicle’s ECU.5. View Freeze FrameWhen an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data. Freeze Data is a snapshot of the operating conditions at the time of an emission-related fault.*Note: If DTCs were erased, Freeze Data may not be stored in vehicle memorydepending on vehicle.6. O2 sensor testThe results of O2 sensor test are not live values but instead the results of the ECU’s last O2 sensor test. For live O2 sensor readings, refer to any of the live sensor screens such as Graph Screen.Not all test values are applicable to all vehicles. Therefore, the list generated will vary depending on vehicle. In addition, not all vehicles support the Oxygen Sensors screen.7. On-board monitor testThis function can be utilized to read the results of on-board diagnostic monitoring tests for specic components/systems.8. EVAP System TestThe EVAP test function lets you initiate a leak test for the vehicle’s EVAP system. The CRP429 does not perform the leak test, but signals to vehicle’s on-board
26LAUNCH CRP429 User's Manualcomputer to initiate the test. Before using the system test function, refer to the vehicle’s service repair manual to determine the procedures necessary to stop the test.9. Vehicle InfoThis option displays the vehicle information, such as VIN (Vehicle Identication Number), CID (Calibration ID) and CVN (Calibration Verication Number).5.4 HistoryGenerally once a vehicle diagnosis is performed, CRP429 will record the every details of diagnostic session. The History function provides direct access to the previously tested vehicles and users can resume from the last operation, without the necessity of starting from scratch. Tap “History” on the Manual Diagnosis main menu screen, all diagnostic records will be listed on the screen in date sequence.Fig. 5-15• Tap certain vehicle model to view the details of the last diagnostic report.• To delete certain diagnostic history, select it and then tap “Delete”. To deleteall historical records, tap “Select All” and then tap “Delete”.
27LAUNCH CRP429 User's ManualEN• Tap “Quick access” to directly navigate to the function selection page of lastdiagnostic operation. Choose the desired option to proceed.5.5 ResettingIn addition to amazing & powerful diagnostic function, CRP429 also features Oil / Service lamp reset etc.There are two methods to reset service lamp: Manual reset or Auto reset. Auto reset follows the principle of sending command from CRP429 to vehicle’s ECU to do resetting. While using manual reset, users just follow the on-screen instructions to select appropriate execution options, enter correct data or values, and perform necessary actions, the system will guide you through the complete performance for various service operations.Follow the owchart shown as below to perform resetting.Select "Reset"Choose the desired service function (e.g. oil lamp reset etc.)Select the desired car brandSelect the reset mode (The available mode varies from vehicle to vehicle)Follow the on-screen instructions to proceed
28LAUNCH CRP429 User's Manual6. UpdateIf some new software or APK can be updated, a numeric indicator will display on the “Upgrade” module on the Job menu. In this case, you may use this option to keep it synchronized with the latest version.*Notes: • To enjoy more funcons and beer service, you are strongly suggested to update it on regular basis. • This funcon requires a stable network connecon.Tap “Upgrade” on the Job menu to enter the update center.By default, all diagnostic software is selected. To deselect certain software, tap “Unselect”, and then check the box next to vehicle model. Tap “Update” to start downloading. It may take several minutes to nish it, please be patient to wait. To pause downloading, tap “Stop”. To resume it, tap “Continue”. If network connection failure occurs, tap “Retry” to try again.Once download is nished, the software packages will be installed automatically.
29LAUNCH CRP429 User's ManualEN7. DataFig. 7-17.1 Diagnostic RecordIf user records the running parameters or waveform graphs while reading data stream, it will be saved as diagnostic records and appear under this tab.Tap “Diagnostic Record” to enter and select the desired data stream items and tap “OK” to jump to the playback page.On-screen Buttons:Graph – displays the parameters in waveform graphs.Combine – this option is mostly used in graph merge status for data comparison. In this case, different items are marked in different colors.Value – this is the default mode which displays the parameters in texts and shows in list format. Frame Playback – plays back the recorded data stream items frame by frame. Once it is in frame playback mode, this button changes into “Auto Playback”.
30LAUNCH CRP429 User's Manual7.2 Diagnostic ReportThis module stores all diagnostic reports generated in process of vehicle diagnosis. All the diagnostic reports are sorted by Date and Make. If there are too many reports stored, tap (Search) to lter and quickly locate it. •To select certain report, just check the box at the right lower corner of thereport. To select all reports, tap “Select All”. To deselect all, tap “Unselect”.•Tap it to view its details.• Select the desired report and then tap “Delete” to delete it.7.3 DTC LibraryThis option helps you to nd the location of the vehicle’s DLC.Fig. 7-2Swipe the screen upwards/downwards to alter the value, then press [OK] button, the screen will display denition of the DTC.
31LAUNCH CRP429 User's ManualEN7.4 DLC(Data Link Connector) LocationThis option helps you to nd the location of the vehicle’s DLC.7.5 ImageThis option enables you to manage the screenshots.7.6 FeedbackThis item allows you to feedback your diagnostic problems to us for analysis and troubleshooting.Tap “Feedback”, the following 3 options will be displayed on the left column of the screen.A. FeedbackTap a tested vehicle model to enter the feedback screen. 1) Tap “Choose File” to open the target folder and choose the desired diagnosticlogs. 2) Choose the failure type and ll in the detailed failure description in the blanktext box and telephone or email address. After inputting, tap “Submit Result” to send it to us.B. HistoryTap it to view all diagnostic feedback records. Different process states are marked with different colors.C. Ofine listTap it to display all diagnostic feedback logs which have not been submitted successfully due to network failure. Once the handset gets a stable network signal, it will be uploaded to the remote server automatically. 7.7 Firmware FixUse this item to upgrade and x diagnostic rmware. During xing, please do not cut power or switch to other interfaces.7.8 User ManualProvides a detailed description on how to operate the CRP429. Before operating the handset, please carefully read it.
32LAUNCH CRP429 User's Manual8. Settings8.1 Units of measurementIt is designed to set the measurement unit. Metric System and English System are available. 8.2 Automatic detection on connectThis option enables you to determine whether to start an automatic VIN detection once CRP429 is properly connected to the vehicle’s DLC.8.3 Display & BrightnessThis item allows you to set the standby time and screen brightness. *Tips: Reducing the brightness of the screen is helpful to conserve the power of the handset.8.4 SoundThis option lets you adjust the volume and other sound settings.8.5 Network*Note: Once WLAN is set as ON, CRP429 will consume more power. While it keepsunused, please set it o to save power. While WLAN keeps unused, please turn it o to conserve baery power. CRP429 has built-in WLAN module that can be used to get online. Once you’re online, you can register your tool, update diagnostic software & APK, send email on your network.Slide the switch to ON, the system starts searching for all available wireless LANs. Choose the desired WLAN access point / network to connect.8.6 Date/TimeThis option allows you to set the system date & time. *Note: Since all diagnostic reports are sorted by Make and Date. To differentiatebetween les, please congure the accurate system me.8.7 LanguageCRP429 supports multiple languages. You can use this option to change the target language.
33LAUNCH CRP429 User's ManualEN8.8 Email SetupThis option is used to set up the default email address for automatically receiving the diagnostic reports.8.9 RecoveryUse this item to reset this tool to the default factory setting. *Warning: Reseng may cause data loss. Before doing so, please be careful to perform this operaon.8.10 VersionBOOT, Download, App and System version are included.8.11 AboutThis option displays the hardware configuration information of the tool and license agreement.
34LAUNCH CRP429 User's Manual9. FAQHere we list some frequently asked questions and answers related to CRP429.1 System halts when reading data stream. What is the reason?It may be caused by a slackened connector. Please turn off the CRP429, rmly connect the connector, and switch it on again.2 Screen of main unit ashes at engine ignition start.Caused by electromagnetic disturbing, and this is normal phenomenon.3 There is no response when communicating with on-board computer.Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is in proper temperature.4 What to do if the system fails to start auto VIN detection?Please check the following possible reasons:•Whether CRP429 is properly connected to the vehicle’s DLC.• Whether the “Automatic detection on Connect” switch is OFF. If yes, slide it toON.5 Why are there so many fault codes?Usually, it’s caused by poor connection or fault circuit grounding.
35LAUNCH CRP429 User's ManualENWarrantyTHIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE LAUNCH PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER’S BUSINESS. LAUNCH electronic product is warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user. This warranty does not cover any part that has been abused, altered, used for a purpose other than for which it was intended, or used in a manner inconsistent with instructions regarding use. The exclusive remedy for any automotive meter found to be defective is repair or replacement, and LAUNCH shall not be liable for any consequential or incidental damages. Final determination of defects shall be made by LAUNCH in accordance with procedures established by LAUNCH. No agent, employee, or representative of LAUNCH has any authority to bind LAUNCH to any afrmation, representation, or warranty concerning LAUNCH automotive meters, except as stated herein. Order InformationReplaceable and optional parts can be ordered directly from your LAUNCH authorized tool supplier. Your order should include the following information:1. Quantity2. Part number3. Item descriptionCustomer ServiceIf you have any questions on the operation of the unit, please contact local dealer, or call 86-755-89366558.Launch website: http://www.cnlaunch.comhttp://www.golo365.comStatement: LAUNCH reserves the rights to make any change to this manual without notice. We have tried our best to make the descriptions and illustrations in the manual as accurate as possible, and defects are inevitable, if you have any question, please contact local dealer or LAUNCH TECH CO., LTD., LAUNCH does not bear any responsibility arising from misunderstandings.

Navigation menu