Launch Tech WIFIPR WIFI Printer User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2157789
Application ID	TNdxgXkTkut/FeLwCxVGzA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	39.79kB (497360 bits)
Date Submitted	2014-01-06 00:00:00
Date Available	2014-01-06 00:00:00
Creation Date	2013-12-30 10:27:23
Producing Software	Adobe PDF Library 8.0
Document Lastmod	2013-12-30 10:27:26
Document Title	User Manual
Document Creator	Adobe InDesign CS3 (5.0)

LAUNCH
LAUNCH
1. Introduction
WI-FI PRINTER
LAUNCH
3. General Controls
This Wi-Fi printer is an optional accessory
of a series of LAUNCH’s diagnostic devices.
The built-in Wi-Fi module enables you to
easily print the real time test results without
connecting any USB cable.
Compared to conventional printers, it is
smaller and easier to carry. Meanwhile,
being free of paper spindle, it is also simple
and fast to load printing paper. In addition
to the included DC power adaptor, it can
be powered alternatively by the built-in
rechargeable battery, which enables you to
use it anytime and anywhere.
User’s Manual
LAUNCH TECH. CO., LTD.
Launch Industrial Park, North of Wuhe
Avenue, Banxuegang, Longgang,
Shenzhen, Guangdong,
P.R.China, 518129
Tel: +86-755-84528767
http://www.cnlaunch.com
http://www.x431.com
LAUNCH
Furthermore, this printer has auto-hibernate
and auto power-off features. While it does
not perform printing operation, it will enter
auto sleeping mode to save power. If no
activities are made within 30 minutes, it will
power off automatically. To start printing,
users need to power it on again.
2. Accessories
a) DC adaptor x 1
b) Rechargeable Lithium battery x 1
c) Thermal printing paper x 1
-1-
test whether thermal paper is properly
installed while the MODE indicator goes
out.
6) CHARGE indicator
[Green]: Indicates the battery is fully
charged.
[Red]: Indicates it is charging.
7) DC 9V adaptor jack (Note: The USB
port next to it is disabled. Do not attempt
to insert the cable into it.)
8) Rechargeable battery
LAUNCH
the compartment with its starting end
approaching to the paper outlet (refer to
the figure shown as below). Reversing
paper direction will result in that no
results will be printed out.
4. Thermal paper loading
This Wi-Fi printer applies thermal paper roll
with size of Φ30×57mm. Follow the steps
described as below to load it.
1. Hold the side notches on the front of the
printer and lift it up to open the cover.
LAUNCH
3. Pull out some printing paper and
introduce it along the slot until it comes
out of the paper outlet shown as below.
Otherwise, paper can not be fed.
1) Side lock notch
2) Paper outlet
3) POWER button: Hold and press it for 2
seconds to turn it on/off.
4) MODE (ready) button: Press it to get
the printer ready or switch it to manual
feed mode.
5) FEED (paper test) button: Press it to
2. Place the unpacked thermal paper into
4. Close the paper cover and press it down
until you hear a click (see the figure
shown on the next page).
-2-
-3-
-4-
Notes:
A. After loading the paper, users need to check
whether the paper can be fed normally. For
details, please refer to “How to print test
results”.
B. If the printer keeps printing for a long time,
the thermal matrixes (shown as below) will
overheat. To avoid a risk of burning injury,
please do NOT touch the matrixes.
Notice: The printer applies the thermal paper,
which should be prevented from being heated
before printing, otherwise, the paper would be
no longer effective or printing results disappear.
-5-
LAUNCH
LAUNCH
5. Using the rechargeable battery
responsibilities for any personal injury or
loss resulting from using other adaptors or
rechargeable batteries not specified in this
user manual.
B. If the printer keeps unattended for a long
period, please remove the rechargeable
battery.
The included rechargeable battery must be
installed to ensure that the printer can print
the test result normally. This printer utilizes
a 7.2V, 1200mAh rechargeable Lithium
battery. Do the following steps to install and
charge it:
1. Align the latches
on the bottom
of the battery
with the holes
(shown as right)
on the battery
compartment.
2. Press the battery down until it is firmly
fitted.
3. Press the [POWER] button for 2 seconds
to turn it on. If the battery is low, the
[POWER] indicator blinks. Please plug
the included adaptor into an outlet
to charge the battery in time. While
charging, the charge indicator turns red.
After charging is complete, the indicator
will turn green. The normal charging time
is 2 hours.
6. Wi-Fi connections
Before printing, you need to make Wi-Fi
connection and settings.
111 Tap “ Settings” on the main menu of
your diagnostic tool.
222 Tap “Wi-Fi” and slide its switch to ON.
333 Locate and tap the X-431PRINTERXXX (XXX stands for 3 numbers).
LAUNCH
the screen once it is successful.
7. How to print test results
There are three indicators on the printer:
* [POWER]: Power indicator
[Red]: Indicates that the printer is on.
[Red and blink]: Indicates that the
rechargeable battery is low.
[Off]: Indicates the printer is off.
* [MODE]: Ready indicator
[Green]: Indicates that the printer is ready.
[Green and blink]: Indicates that no thermal
paper is loaded or the printer runs out of
paper.
[Off]: Indicates that the printer is switched
to manual feed mode.
LAUNCH
shows that the printer is ready.
FCC Warning:
appears on the top of the
If the printer icon
screen, it means that printing operation can
be done. Tap it to start printing.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Notes:
A. Never expose the apparatus to sunshine,
rain, or water.
B. Make sure that this apparatus operates in
the following conditions:
Working temperature: -10oC~50oC
Working humidity: 5oC RH~90oC RH.
444 Input the identity password (default
factory value is 12345678) and tap
“Connect”. “Connected” will appear on
-6-
-7-
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
Press the [POWER] button for 2 seconds
to turn it on, the [MODE] indicator will blink
and then remain on. (Every time you load or
change the paper, press the [MODE] button
to turn off the indicator first, and then press
[FEED] to test whether paper can be fed
normally.) When the [MODE] indicator is on, it
Statement: LAUNCH reserves the rights
to make any change to product designs and
specifications without notice. The actual object
may differ a little from the descriptions in the
manual in physical appearance, color and
configuration.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
-8-
-9-
- 10 -
* [FEED]: Paper test indicator
[Green]: Indicates that users can press the
[FEED] button to check whether the paper
is fed normally.
[Off]: Indicates that manual mode is off.
Notes:
A. Please use the included DC adaptor and
rechargeable battery only. We assume no
LAUNCH
LAUNCH
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the
equipment and receiver.
-- Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced
radio/TV technician for help.
RF warning
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be
installed and operated with minimum distance
20cm between the radiator & your body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c006 1.236519, Wed Jun 14 2006 08:31:24
Instance ID                     : uuid:3cb70fb8-339d-41ce-9f39-57e5c88e8536
Document ID                     : adobe:docid:indd:f0ee5677-70f8-11e3-928f-c83539877a47
Rendition Class                 : proof:pdf
Derived From Instance ID        : acb10d42-5342-11e3-97e3-fe4d7a037f9c
Derived From Document ID        : adobe:docid:indd:b90fca64-4bfc-11e3-8037-ca7a7709c44e
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 300.00, 200.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00
Manifest Placed Y Resolution    : 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 300.00, 200.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:faefaac3-f3e4-11e0-9f1e-fc0acb10e015, uuid:faefaac8-f3e4-11e0-9f1e-fc0acb10e015, uuid:61e274ee-f3e5-11e0-9f1e-fc0acb10e015, uuid:22b52371-f3e7-11e0-9f1e-fc0acb10e015, uuid:f74823da-4c39-11e3-a7f7-d25e97b81da1, uuid:13e55fc1-4c2b-11e3-baa5-a549f3c2b719, uuid:61e274f3-f3e5-11e0-9f1e-fc0acb10e015, uuid:74178186-c724-11e0-8009-f4493572bad6, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:cbb47d6e-e5b3-11e0-97ac-d9c5e79dd7af, uuid:fb054175-4cd4-11e3-8e66-ac8bfe8272fe
Manifest Reference Document ID  : adobe:docid:photoshop:85ff8f5a-bfe0-11e0-85d5-abfd7d56bbb9, adobe:docid:photoshop:a06266ed-bff4-11e0-85d5-abfd7d56bbb9, adobe:docid:photoshop:66812fb6-bff5-11e0-85d5-abfd7d56bbb9, adobe:docid:photoshop:25fcabf0-c7b6-11e0-9e92-9bb8d56fe103, adobe:docid:photoshop:f74823d9-4c39-11e3-a7f7-d25e97b81da1, adobe:docid:photoshop:df1500b1-4c2a-11e3-baa5-a549f3c2b719, adobe:docid:photoshop:acaa2521-bff2-11e0-85d5-abfd7d56bbb9, adobe:docid:photoshop:74178185-c724-11e0-8009-f4493572bad6, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:cbb47d6d-e5b3-11e0-97ac-d9c5e79dd7af, adobe:docid:photoshop:fb054174-4cd4-11e3-8e66-ac8bfe8272fe
Create Date                     : 2013:12:30 10:27:23+08:00
Modify Date                     : 2013:12:30 10:27:26+08:00
Metadata Date                   : 2013:12:30 10:27:26+08:00
Creator Tool                    : Adobe InDesign CS3 (5.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 4658 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 1
Creator                         : Adobe InDesign CS3 (5.0)

EXIF Metadata provided by EXIF.tools