Launch Tech X631WAMU X-631 + Main Unit User Manual X 631 RF User s Manual
Launch Tech Co., Ltd. X-631 + Main Unit X 631 RF User s Manual
User Manual
X-631 RF User's Manual
V6.00.000
2012-06-25
Trademark Information
LAUNCH is a reg istered trademark of LAUNCH TECH. CO., LTD. (short for LAUNCH) in
China and other countries. All other LAUNCH trademarks, service marks, domain names, logos,
and company names referred t o in this manual are either trademarks, registered trademarks,
service marks, domain names, l ogos, company names of or are otherwise the property of
LAUNCH or its affiliates. In countries where any of the LAUNCH trad emarks, service marks,
domain names, logos and company names are not registered, LAUNCH claims o ther rights
associated with unregistered trademarks, service m arks, domain names, logos, and company
names. Other products or company names referred to in this manual may be trademarks of their
respective owners. You may not use any trademarks, service marks, domain names, logos, or
company names of LAUNCH o r any third party without permission from the owner of the
applicable trademarks, service m arks, domain names, logos, or c ompany names. You may
contact LAUNCH b y visiting Launch at http://www.cnlaunch.com, or w riting to Launch
Industrial Park, North of Wuhe Rd., Banxuegang, Longgang, Shenzhen, Guangdong, P. R.
China, to request written permission to use Materials on this manual for purposes or for all
other questions relating to this manual.
Copyright Information
Copyright © 2010 by Launch Tech Co., Ltd. All rights reserved. No part of this publication may
be reproduced, stored in a retrieval system, or tra nsmitted in any form or by any means,
electronic, mechanical, photocopying, recording or otherwise, without the prior written
permission of LAUNCH. The information contained herein is designed only for the use of this
unit. LAUNCH is not responsible for any use of this information as applied to other units.
Neither LAUNCH nor its affiliates shall be liable to the purchaser of this unit or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident,
misuse, or abuse of this unit, or unauthorized modifications, repairs, or alterations to this unit,
or failure to strictly comply with LAUNCH operating and maintenance instructions.
LAUNCH shall not be liable fo r any damages or problems arising from the use of any options
or any cons umable products other than those designated as Original LAUNCH Products or
LAUNCH Approved Products by LAUNCH.
General Notice
Other product names used herein are for identification purposes only and may be trademarks of their
respective owners. LAUNCH disclaims any and all rights in those marks.
1. X-631 RF
The system power supply is provided by the USB of PC. The power supply is 5.0V.
The computer communicate with RF by the serial port DB9.
2. The RF connect with PC
DB9
USB
X-631 antenna
Wire for Power supply and
communicate
X-631 RF
3. frequency
The RF transmit have 16 frequency channels. The frequency can be selected in the
16 frequency channels.
Channel List:
channel frequency
（MHz）
channel frequency
（MHz）
1 2402 9 2419
2 2404 10 2425
3 2406 11 2431
4 2408 12 2434
5 2410 13 2437
6 2412 14 2440
7 2414 15 2443
8 2416 16 2446
The state of sw1 must be cha nged when change the frequency of RF . The shorting cap is
connect 2 ,3 of SW1 when the RF communicate. The 1,2 of SW1 be shorted circuit when
set frequency or change frequency. The XH plug be pulled out before change the state
of SW1. The XH plug be connected after change the state of SW1.
After change state of SW 1, the state of SW1 is1,2 of SW1 be shorted circuit, find
the module setting program , select the 2.4G module. Click the icon “read m odule
frequency”, can get the frequency of RF . Select the frequency of you want, click the
icon “set module frequency”, you change the frequency of RF.
Only connect Wire
for Power supply
and communicate
Power LED
SW1 W ork
/set fre
q
uenc
y
Receive
indicator LED
Transmit
indicator LED
shorting cap
module setting program
FCC ID: XUJX631WAMU
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.