Leap Devices NTX RadioPopper User Manual

Leap Devices, LLC RadioPopper

User Manual

4567NanoUser GuideAfter each trigger or test trigger, the Nano will indicate its battery level by blinking 1, 2, 3, or 4 lights.Approximate Battery Level1 2 3 41 2 3 41 2 3 41 2 3 4100%75%50%25%Touch Sensitive ButtonsYour new RadioPopper Nano features touch sensitive buttons. There is no need to “press” on the unit. Simply touch your nger to the button area.Touch and hold POWER/TEST to turn the unit on or o.Power Saving ModeIn the unlikely event your Nano is left on or is accidentally powered on when not in use, several power saving features have been included in both the transmitter and receiver units. These features will automatically power down the Nano to prevent unintentional drain of battery.Guide ContentsBattery Level Indicator . . . . . . . . . . . . . . .Touch Sensitive Buttons . . . . . . . . . . . . .Power Saving Modes . . . . . . . . . . . . . . . .Transmitter Auto Power O . . . . . . . . . .Receiver Auto Power O . . . . . . . . . . . . .RadioPopper Support . . . . . . . . . . . . . . .Nano Specications . . . . . . . . . . . . . . . . . FCC & IC Statements . . . . . . . . . . . . . . . . .4567891011NANO1 2 3 4CHANSET POWERTESTDouble Tap:Change ChannelTouch & Hold:Power On/OSingle Tap:Test TriggerLight blinks to indicate channelTransmitter Auto Power OIf your Nano transmitter is not triggered or test red for more than one hour, it will automatically power down. If you trigger the Nano transmitter after this power down (by taking a picture with your camera for example), the Nano will automatically power up and resume normal operation.
8910Receiver Auto Power OYour Nano receiver senses when it is attached to a ash or studio strobe. If there is nothing attached (or turned on) for more than ve minutes, the Nano receiver will automatically power down. Once it again senses an attached ash or studio light, the Nano receiver will automatically power up and resume normal operation.SupportSpecicationsWe love and support our customers. Contact us anytime if you have any questions.www.radiopopper.comsupport@radiopopper.com360-713-0776Battery (Tx and Rx): One “CR123” Size Battery, 3.0v. Rechargeable approved.Battery Life: Approx 100 Hours total power-on time per battery.Radio Frequency:902-928 MHz, ISM BandRadio Range:300 ft to 1500 ft depending on conditions and environment.Maximum Sync Speed: 1/500 for cameras having leaf shutters. FCC STATEMENTThis equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:* Reorient or relocate the receiving antenna.* Increase the separation between the equipment and receiver.* Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.* Consult the dealer or an experienced radio/TV technician for help.This equipment has been veried to comply with the limits for a class B computing device, pursuant to FCC Rules. Operation with non-approved equipment is likely to result in interference to radio and TV reception. The user is cautioned that changes and modications made to the equipment without the approval of manufacturer could void the user’s authority to operate this equipment.Important Note: To comply with FCC RF exposure compliance requirements, the following antenna installation and device operating congurations must be satised - This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. INDUSTRY CANADA INFORMATIONThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.FCC ID: V4TNTXThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference and(2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu