Learning Resources Inc Microscope And Magnifier Ler 4411 X10 Users Manual

LER 4411 X10 to the manual 3b97a3af-6261-4088-8e7c-235f7291c2d6

: Learning-Resources Learning-Resources-Learning-Resources-Inc-Microscope-And-Magnifier-Ler-4411-X10-Users-Manual-570643 learning-resources-learning-resources-inc-microscope-and-magnifier-ler-4411-x10-users-manual-570643 learning-resources pdf

Open the PDF directly: View PDF .
Page Count: 2

LER 4 411

X10~X200 1.3 MP Digital Microscope

Please Read All Instructions Carefully Before Using

User Guide

Twist™ User Guide Twist™ User Guide Twist™ User Guide Twist™ User GuideTwist™ User Guide Twist™ User Guide Twist™ User Guide

2468357

•   Please retain these instructions for future reference.

•   Do not allow your Twist™ to come into contact with 

water or other liquids.

•   In the event of an electro-static discharge, your Twist™

may malfunction. In this case, you may need to 

disconnect from the computer to reset it.

•   Warranty is void if the case is opened for any reason.

•   The warranty does not cover any data loss from the 

unit nor any consequential loss of information.

FCC compliance

NOTE:

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY 

RADIO OR TV INTERFERENCE CAUSED BY 

UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. 

SUCH MODIFICATIONS COULD VOID THE USER’S 

AUTHORITY TO OPERATE THE EQUIPMENT

NOTE: This equipment has been tested and found to 

comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against 

harmful interference in a residential installation. This 

equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful 

interference to radio communications. However, there is 

no guarantee that interference will not occur in a 

particular installation.

If this equipment does cause harmful interference to 

radio or television reception, which can be determined 

by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or 

more of the following measures:

•   Reorient or relocate the receiving antenna 

•   Increase the separation between the equipment 

and receiver 

•   Connect the equipment into an outlet on a circuit 

different from that to which the receiver is connected 

•   Consult the dealer or an experienced radio/TV 

technician for help

Know Your Twist™Twist™ Controls

There are two buttons on the base of the Twist™:

•   Press the snapshot button to take 

a new picture 

•   Press the Light button to turn on 

the LEDs 

In addition to the camera button, Twist™ has a 3.5 mm 

mono jack socket so that external switches can be used 

to take pictures.

Twist™

Flexible Digital Microscope

Bendy 

gooseneck

Focus wheel

LED lights

LED light on/off

Photo button

Ext photo switch socket

To adjust the focus, rotate the adjustment wheel slowly 

until the image on the screen is clearly displayed.

Marking on label shows reference figure for measurement  

(for user with “Flexi-measure” software only).

Using the Twist™/Flexi-Scope™ software

Control Panel

Current image

Maximize image

Main display

Saved images

Place CD into CD-ROM

drive and follow steps

shown on screen, then

reboot PC before you

start the program

To start the program, go to “Start” 

“Twist™”/”Flexi-Scope™”

Click this icon to take a picture. 

Pictures taken will be stored in the 

Folder “C\MyPic130” by default

Video settings

Start video recording and choose the 

Video settings. Videos will be stored 

in C\MyVideo130 by default 

Allows the user to take pictures and video 

automatically at set intervals 

Click this icon to launch the “Flexi-Measure” 

application 

Click this icon to Exit the program

Using the Flexi-Measure software

Dimension 

tools

Color & font

Foot notes

Measurement 

settings

Capture the image and

read the magnification

reference number from

the focus wheel. Enter

this figure into the

magnification box

Before measurement,

you need to know the

Magnification reference

number of the captured

images and enter it into

the magnification box”

Twist™ User Guide Twist™ User Guide Twist™ User Guide Twist™ User GuideTwist™ User Guide Twist™ User Guide Twist™ User Guide Twist™ User Guide

10 12 14 16911 13 15

Problem Image is too dark

Solution Turn on LED lamp for extra illumination

Problem Image is not in focus

Solution Slowly rotate the focus wheel until the 

displayed image is in focus

Problem Magnification is too low

Solution Move the Twist™ nearer to the object and 

refocus. The nearer the Twist™ is to the 

object, the higher the magnification will be

Support & Warranty

This product is provided with a one-year warranty for 

problems found during normal usage. Mistreating the 

Twis t™ or opening the unit will invalidate this warranty. 

Any data stored on the unit and any consequential loss 

is not covered by this warranty. The battery is not user 

replaceable.

All out-of-warranty repairs will be subject to a 

replacement fee.

Please visit www.LearningResources.com for the latest 

product information and technical support.

©  Learning Resources, Inc., Vernon Hills, IL (U.S.A.)

  Please retain our address for future reference.

  Made in China.         LRM4411-GUD

  Fabriqué en Chine.  Informations à conserver.

  Made in China.  Bitte bewahren Sie unsere 

    Adresse für spätere 

    Nachfragen auf.

  Hecho en China.  Conservar estos datos.

This device complies with Part 15 of the FCC Rules. 

Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and 

(2) This device must accept any interference received, 

including interference that may cause undesired 

operation.

Warning: Changes or modifications to this unit not 

expressly approved by the party responsible for 

compliance could void the user’s authority to operate 

the equipment. 

You can draw a 

circle by moving 

the cursor to 

3 points

Settings

All captured images are saved in 

“C:\MyPic130” by default. Opening a 

captured image will display the image 

on the screen for measurement.

Click “Save” to save images to any desired 

location.

To email an image instantly, Click “email.” 

This will load your default email program 

(applicable for Microsoft Outlook only).

Click this icon if you want to “undo” your 

previous action.

Click this icon to choose the color of the line 

or circle you want to show on screen.

You can add footnotes on photo. Click this 

icon and move cursor to the place where you 

want to add text; then input your text in the 

blank text box. 

Click this icon to choose the font size. 

Click this icon to choose the footnote font 

size & color

Click on this icon to enter the magnification 

reference (this must be done before making 

measurements)

Technical specification

Image Sensor  1.3 Megapixels Color Sensor

Resolution  1.3 M pixel (1280 x 960)

Frame rate  30 fps

Magnification  10X–200X

LED lamp   6 LED light for illumination

Lens     High-precision glass lens with filter

OS Support  Windows XP / Vista

Interface    High-speed USB 2.0

Troubleshooting

Twis t™ is designed to work reliably and predictably in all 

normal conditions. However, it is possible that problems 

may occur. Please check the following before contacting 

technical support:

Using your TWIST™ with Mac.

In addition to using the Twist™ with your PC, the Twist™

is also compatible with Mac ( OS 10.6 and above). 

Here’s how to get started:  

  1.  Insert the included CD into your Mac.

  2.  Drag the TWIST™ MAC software to your desktop.

  3.  To launch the software, click on both       

  “MICROMEASURE” and “MICROCAPTURE”.

Your opinion matters! Visit

www.LearningResources.com

to write a product review or to

find a store near you.

Images 

Capture

 X-Y  

Axis

Coordinate

Video 

Record

Settings

Measure Exit

Schedule