Lectrosonics HHAC1 Wireless Microphone Transmitter User Manual HHa man indd
Lectrosonics Inc Wireless Microphone Transmitter HHa man indd
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2792538 |
| Application ID | tqsXmqtEVtNDJgEAeOkTMA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 244.76kB (3059562 bits) |
| Date Submitted | 2015-10-24 00:00:00 |
| Date Available | 2016-04-20 00:00:00 |
| Creation Date | 2017-09-07 09:54:31 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-09-07 09:54:31 |
| Document Title | HHa_man.indd |
| Document Creator | Adobe InDesign CC 2015 (Windows) |
INSTRUCTION MANUAL HHa Handheld Transmitter Digital Hybrid Wireless® US Patent 7,225,135 Rio Rancho, NM, USA www.lectrosonics.com HHa LECTROSONICS, INC. Wideband Hand Held Transmitter Table of Contents General Technical Description ............................................. 4 Microphone Capsules: .......................................................... 6 Mechanical Assembly ........................................................... 6 Battery Installation ................................................................ 7 IR Sync ................................................................................... 7 Control Panel ......................................................................... 7 Setup and Adjustments ........................................................ 7 Powering On ........................................................................ 7 Powering Off ........................................................................ 8 Standby Mode ...................................................................... 8 Power Menu ......................................................................... 8 Battery Condition ................................................................. 8 Navigating Menus and Screens ........................................... 8 Input Gain Adjustment ........................................................ 10 Side Button Functions ........................................................ 11 Mic Capsule Adjustments ................................................... 12 (EXPERT LEVEL ADJUSTMENT) ..................................... 12 Firmware Updates ............................................................... 13 Parts and Accessories ........................................................ 14 Troubleshooting................................................................... 15 Speciications ...................................................................... 16 Service and Repair .............................................................. 17 Returning Units for Repair ................................................. 17 Consumer Alert for US Users - FCC Order DA 10-92 Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this microphone system without a license is subject to certain restrictions: the system may not cause harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device. Purchasers should also be aware that the FCC is currently evaluating use of wireless microphone systems, and these rules are subject to change. For more information, call the FCC at 1-888- CALL-FCC (TTY: 1-888-TELL-FCC) or visit the FCC’s wireless microphone website at www.fcc.gov/cgb/wirelessmicrophones. To operate wireless microphone systems at power greater than 50mW, you must qualify as a Part 74 user and be licensed. If you qualify and wish to apply for a license go to: http://www.fcc.gov/Forms/Form601/601.html Rio Rancho, NM HHa General Technical Description Digital Hybrid Wireless® Technology Introduction The HHa handheld transmitter uses state-of-the-art Digital Hybrid Wireless® wireless technology, selectable output power and a versatile microphone capsule mounting system to meet the needs of audio professionals and vocalists. The compandor-free Digital Hybrid audio chain preserves the quality of the selected microphone capsule and delivers it to the sound and recording system without coloration. This superb audio performance and highly reliable RF transmission makes it ideally suited for high end stage and studio production. Digital Signal Processor The DSP encodes the digitized audio from the A-D converter and adds an ultrasonic pilot tone to control the receiver’s squelch in systems that use pilot tone. It also controls the input limiter and audio metering. Compatibility Modes The transmitter was designed to operate with Lectrosonics Digital Hybrid Wireless® receivers and will yield the best performance when doing so. Due to the lexibility of digital signal processing, however, the transmitter is also able to operate with Lectrosonics 200 Series, Lectrosonics 100 Series, IFB and certain non-Lectrosonics analog receivers in special compatibility modes. (Contact the Lectrosonics Sales Department for a complete list of compatible receivers.) Bias 5V Phantom Power Mic capsule Interface Input Amp Digital Pot All wireless links suffer from channel noise to some degree and all wireless microphone systems seek to minimize the impact of that noise on the desired signal. Conventional analog systems use compandors to increase the signal to noise ratio, at the cost of distortion artifacts. Wholly digital systems defeat the noise by sending the audio information in digital form, at the cost of some combination of power, bandwidth or channel count. The Lectrosonics Digital Hybrid Wireless® system overcomes channel noise by digitally encoding the audio in the transmitter and decoding it in the receiver, yet still sending the encoded information via an analog FM wireless link. This proprietary algorithm is not a digital implementation of an analog compandor. Instead, it is a technique that can be accomplished only in the digital domain, even though the inputs and outputs are analog signals. Because it uses an analog FM link, the system enjoys all the beneits of conventional FM wireless systems, such as excellent range, eficient use of RF spectrum, and long battery life. However, unlike conventional FM systems, the design has eliminated the analog compandor and its artifacts. Wide Deviation ±75 kHz deviation is used in the Digital Hybrid and 200 Series compatibility modes to dramatically improve the capture ratio, signal to noise ratio and dynamic range of the wireless system. This, in conjunction with accurate input gain adjustment, produces outstanding audio quality that rivals a hard wired connection. +7V Hi.Lo Pass Filter Audio A-D Converter 11001001 D-A Converter Encoded Audio and Pilot Tone Filter Amp Variable Switching Power Supply 11001001 Audio Level Digital Signal Processor Shunt Limiter 3V Battery Switching Power Supply Microprocessor Reference Crystal LCD BACK MUTE POWER Bicolor Modulation LEDs Control Panel MENU/SEL Phase Locked Loop Reference Crystal Voltage Controlled Oscillator Final Amplifier LECTROSONICS, INC. Wideband Hand Held Transmitter Pilot Tone Squelch The beneit of the pilot tone squelch system is that the associated receiver will remain muted until it receives the pilot tone from the matching transmitter, even if a strong RF signal is present on the carrier frequency of the system. All Digital Hybrid Wireless® transmitters use one of 256 different ultrasonic tones between 25 and 32 kHz in each standard frequency block to operate the receiver squelch. The HHa is a wideband design that tunes across three standard blocks (up to 76 MHz). The pilot tone frequency is determined by the selected operating frequency in 100 kHz steps. In other words, the same pilot tone is used for all four frequencies within each 100 kHz step of the tuning range. This preserves compatibility with earlier Digital Hybrid products that tune across a single frequency block (25.6 MHz). Input Gain Range and Limiter 45 dB range of input gain adjustment allows gain settings to accurately match the user’s voice and the varying sensitivity of different microphone capsules. A DSP-controlled analog audio limiter is employed before the A-D converter. The limiter has a range of more than 30 dB for excellent overload protection. A dual release envelope makes the limiter acoustically transparent while maintaining low distortion. It can be thought of as two limiters in series, a fast attack and release limiter followed by a slow attack and release limiter. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels to keep audio distortion low while preserving short term dynamics. Long Battery Life Switching power supplies throughout the design allow over 5 hours of operation using two alkaline AA batteries. Lithium batteries will provide over 8 hours of operation. The battery compartment and contacts are designed to prevent “rattle” as the unit is handled. Menu-Driven Control A high-resolution LCD and control panel with membrane switches provide access to the menu-driven setup. Transmitter RF power, high-pass ilter, frequency selection, backlight timeout, mute or talkback functions and tuning modes are easily accessed. Wideband Tuning Range The transmitter can tune across band of up to 76 MHz in either 100 kHz or 25 kHz steps. Rio Rancho, NM Frequency Selection Operating frequency is normally selected using a receiver or analyzer to assess signals in the local environment to avoid interference. Once an interferencefree frequency is identiied, the transmitter frequency is set to match the receiver. The LCD on the transmitter displays frequency in MHz and with a two character hex code that is used on most Lectrosonics receivers. Antenna A newly designed helical antenna allows the transmitter to be held in any position, since the user’s hands have little or no effect on the RF output power. Microphone Capsules The transmitter is available from Lectrosonics with the HHC and HHVMC cardioid condenser capsules. Capsules from several other manufacturers are also available for use with the HH: those with a 1.25” x 28 thread pitch and three contact rings. Condenser or dynamic microphone heads can be used with the HH, depending on the user’s preference or the application. IR (infrared) Sync An IR Sync Port is used for quick setup with receivers that offer this feature. Settings for frequency, step size and compatibility mode are transferred from receiver to transmitter via the IR ports. Side Button Functions A programmable switch on the side of the housing can be conigured as a mute/cough switch, to provide a talkback function, a power switch, or be disabled. The talkback function provides a communication channel when used with a receiver equipped with this feature, such as a Venue Wideband receiver with appropriate irmware. When pressed and held in, the side switch re-directs the audio output to a different audio channel on the receiver. As soon as the switch is released, audio is returned to the program channel. The talkback function works only in the Digital Hybrid compatibility mode. USB Port for Firmware Updates Firmware updates are enabled by simply downloading a ile and utility program from the Lectrosonics web site, connecting the transmitter to a computer via the USB port and running the program. HHa A mic capsule is threaded onto the body of the transmitter in the direction shown. Do not overtighten it. Mechanical Assembly The lower housing opens by rotating it in the direction shown. After the threads are disengaged, pull the housing downward until it engages the detent that holds it open. The threaded interface is a 1.25” diameter opening with 28 threads per inch and three contact rings Microphone Capsules: Lectrosonics offers two types of capsules. The HHC is the standard capsule and the HHVMC is the Variable Mic Capsule which includes adjustments for Bass, Midrange and Treble. Do not touch the contacts between the mic capsule and transmitter body. When necessary, the contacts can be cleaned with a cotton swab and alcohol. HHC Lectrosonics cardioid electret Capsule Installation HHVMC Lectrosonics cardioid electret with VariMic preamp Along with these two models from Lectrosonics, a variety of different capsules with a common thread and electrical interface are available from the major microphone manufacturers. Capsules are attached with a right-hand thread. To remove the windscreen from the mic capsule, line up the blue wrench (included with the capsule head) with the lat notches on the lower threaded area of the mic capsule. Align lats on the wrench with lats on the capsule. A list of compatible capsules is on the website at www. lectrosonics.com listed on the HH transmitter page. *All product names are trademarks of their respective owners, which are in no way affiliated with Lectrosonics. LECTROSONICS, INC. Wideband Hand Held Transmitter Battery Installation To insert batteries, close the eject lever and insert the upper contacts irst (closest to the mic capsule). Polarity is marked on the label in the bottom of the battery compartment. Control Panel Six membrane switches on the control panel are used to set up the transmitter by navigating the menus on the LCD and selecting the desired values. UP/DOWN Buttons for Menu Item Selection Power Button Close eject lever to install batteries Modulation LEDs IR Sync Port Enter Menu and Select Item To remove the batteries, pull the eject lever outward. The battery tips will move outward, making them easier to grasp. Pull eject lever outward to release batteries from contacts Previous Screen Side Button Setup Switch Setup and Adjustments Powering On Press and hold the Power Button for several seconds until a countdown on the LCD is completed. The countdown from 1 through 3 will appear on the LCD, followed by a display of the model, irmware version, frequency block and compatibility mode. The contacts are very tight to prevent the batteries from “rattling” as the transmitter is being handled. IR Sync The IR SYNC (infrared sync) port is used with receivers that offer this feature. Settings stored in the receiver for frequency, step size and compatibility mode are transferred to the transmitter via the infrared ports. To use this feature, open the housing on the transmitter to expose the control panel. Hold the transmitter near the receiver (less than 3 feet away) so the IR ports face each other. The transfer is triggered by a switch on the receiver. The LCD on the transmitter will display a message conirming that the settings were successfully transferred, or an error message that identiies the problem that occurred. IR Sync OK Rio Rancho, NM HH V1.00 Blk 24 Hybrid Hold for Rf On ...3 When you release the button, the unit will be operational with the RF output turned on and the Main Window displayed. 5A The Main Window 623.400 -40 -20 NOTE: If the Power Button is released before the countdown is completed, the unit will boot up in the “standby” mode with the RF output turned off. Button Cough HHa Powering Off Battery Condition Press and hold the Power Button (or the side button if it is conigured for turning the power on and off) for several seconds and observe the countdown on the LCD. The countdown on the LCD will progress from 3 to 1 and the power will then be turned off. This can be done from any menu or screen. Powering Off . . . NOTE: If the Power Button is released before the countdown is completed, the unit will remain turned on and the LCD will return to the same screen or menu that was displayed previously. Standby Mode A brief push of the Power Button turns the unit on and places it into a “standby” mode (not transmitting). This allows the transmitter to be set up without the risk of creating interference for other wireless systems that are operating in the vicinity. A notice will appear briely conirming that the RF output of the transmitter is turned off, followed by the Main Window. The antenna symbol will blink as a reminder that the RF output is turned off. Rf Off 5A -20 5A 623.400 -40 -20 Battery Gauge Rechargeable batteries give little or no warning when nearing depletion. If you use rechargeable batteries in the HH, we recommend trying fully charged batteries irst, noting the length of time that the batteries will run the unit, and in the future using somewhat less than that time to determine when the battery needs to be replaced. The Venue and other receivers from Lectrosonics offer a timer function to assist in this process. Navigating Menus and Screens The Main Window displays the following information: Power Menu Icon indicates whether RF output is turned on or off Hex Code for Operating frequency 5A TB Symbol blinks when RF output is turned OFF MUTE 623.400 -40 An icon on the Main Window indicates the remaining power of the transmitter batteries. This battery gauge is most accurate with the typical voltage drop across the life of alkaline and dry cell lithium batteries. Battery condition 623.400 Operating frequency in MHz -40 -20 Function of the rear panel switch (talkback button) Audio level When the transmitter is turned on, a brief push of the Power Button will reveal a menu allowing you to choose between Resume, Rf On?, and Pwr Off?. 1) Press the MENU/SEL button to enter the setup menu. Use the UP/DOWN buttons to highlight the menu item. Use the UP/DOWN buttons to select one of the menu items, then press the MENU/SEL button to conirm this action. The Rf On? selection will enter another screen prompting a Yes or No answer. 2) Press the MENU/SEL button to enter the setup screen for that item. Use the UP/DOWN buttons to select the desired value or mode. Resume Rf On? Pwr Off? • Resume: Continue operating in the same condition as before. • Rf On?: Begin transmitting the RF signal. • Pwr Off?: Turns off the transmitter. Gain Freq. Button Rolloff Gain 25 -40 -20 3) Press the MENU/SEL button to save this setting and return to the previous screen. 4) Press the BACK button to return to the Main Window. The unit can also be turned off from any menu or screen on the LCD by holding the power button in for the duration of the countdown. LECTROSONICS, INC. Wideband Hand Held Transmitter Gain Compat This setting is very important since it will determine the audio signal to noise ratio and dynamic range that the wireless system will deliver. Gain must be set according to the individual voice, the mic capsule in use and the handling technique of the user. LEDs in the control panel facilitate accurate gain adjustment. Gain Freq. Button Rolloff Gain 25 -40 -20 IMPORTANT: See the section Input Gain Adjustment on page 10 for details. Freq. The operating frequency is normally determined using the scanning function in the receiver or with coordination software. The frequency is shown on the transmitter LCD display in MHz and with a hexadecimal code that is used on most Lectrosonics receivers. Gain Freq. Button Rolloff Freq 8A 628.200 -40 -20 Button The Side Button on the housing can be set to provide several functions, or it can be bypassed. Gain Freq. Button Rolloff Functions: TalkBack Power Cough Mute (none) See page 11 for details Compat Hybrid The available modes are as follows: • • • • • • Hybrid Mode 3 200 Mode 100 Mode Mode 6 IFB Mode Digital Hybrid receivers (other brand contact the factory) Earlier Lectrosonics receivers 100 Series Lectrosonics receivers (other brand contact the factory) Lectrosonics IFB receivers Tuning The frequency can be adjusted in 100 kHz or 25 kHz steps to match the receiver. 100 kHz is the standard increment for Lectrosonics wireless systems, but 25 kHz increments may be needed for use with systems from other manufacturers or when frequency coordination requires it. Compat Tuning TxPower Phase Tuning 100 kHz 25 kHz The Hex Code on the Main Screen will be smaller in the 25 kHz mode and a fraction will appear next to the characters if a frequency in between even 100 kHz steps is selected. Gain 25 A low frequency roll-off ilter can be set for a -3dB point at 35, 50, 70, 100 or 125 Hz. Roll-off slopes are 12.2 dB/octave at 35 Hz and 10.1 dB/octave at 70 Hz through 125 Hz. Rolloff 70 Hz The roll-off frequency is normally adjusted by ear to suit personal preferences. Rio Rancho, NM Compat Tuning TxPower Phase Button Rolloff Gain Freq. Button Rolloff The HH can be used with earlier Lectrosonics wireless and IFB systems and systems from other manufacturers by selecting the correct Compatibility Mode. The receiver must be set to the same mode. Cough -40 -20 TxPower Output power can be set to 100 mW to extend operating range (which can also suppress noise and dropouts to some extent) or set to 50 mW to slightly extend the operating life of the batteries. Compat Tuning TxPower Phase TxPower 50 mW 100 mW HHa Phase The phase (polarity) of the audio can be inverted to match other microphone capsules as needed. TxPower Phase Backlgt Rf On? Phase Input Gain Adjustment The two bicolor Modulation LEDs (located at the bottom of the control panel) provide a visual indication of the audio signal level entering the transmitter. 5A Pos Neg 623.400 Backlgt -40 The LCD includes a backlight that illuminates the display for easier viewing in dim lighting conditions. It is set to come on when any button on the control panel is pressed, then stay on for either 30 seconds or 5 minutes, or to stay on all the time. Compat Tuning TxPower Backlgt Backlgt On 30 sec 5 min Rf On? The transmitter output can be switched on or off with this menu item. This is useful, for example, when the transmitter is in the “standby” mode during setup, allowing it to be turned on for normal operation without having to cycle the power. Tuning TxPower Backlgt Rf On? Rf On? No Yes This menu item can also be used to change the transmitter to the “standby” mode with the RF output turned off for additional setup. Default The default setting simple returns the transmitter back to the factory settings and any of the menu items can be readjusted from that default point. TxPower Backlgt Rf On? Default Default settings No Yes -20 The audio level is shown by LEDs and in the LCD screen. The gain should be set so that the -20 LED just turns red on the loudest peak (the onset of limiting). The LEDs will glow either red or green to indicate modulation levels as shown in the following table. Signal Level -20 LED -10 LED Less than -20 dB Off Off -20 dB to -10 dB Green Off -10 dB to +0 dB Green Green +0 dB to +10 dB Red Green Greater than +10 dB Red Red It is best to go through the following procedure with the transmitter in the “standby” mode so that no audio will enter the sound system, which could cause feedback. 1) With fresh batteries in the transmitter, power the unit on into “standby” (no transmission) mode. 2) Press the MENU/SEL button once to enter the setup menu. Use the UP/DOWN buttons to select Gain. Press the MENU/SEL button again to enter the setup screen. 3) Hold the microphone the way it will be used in actual operation. 4) Speak or sing at the same voice level that will actually be used during the program, while observing the modulation LEDs. Use the UP/DOWN buttons to adjust the gain until the –20 dB LED starts to licker red and the –10 dB glows green. 5) Once the audio gain has been set, the signal can be sent through the sound system for overall level adjustments, monitor settings, etc. To do this, the unit must be set to transmit (see Powering On and Off, and the Standby Mode on page 7). NOTE: Full modulation is achieved when the -20 LED irst turns red. 30 dB of clean limiting is available above this point. 10 LECTROSONICS, INC. Wideband Hand Held Transmitter Side Button Functions Cough A special button (the Side Button) on the outside of the housing can be conigured to provide a several different functions, or to be inoperative. Side Button Functions: • TalkBack • Power • Cough • Mute • (none) Button Mute The Side Button Setup Switch on the control panel opens a setup screen to set the Side Button function. Enter this setup screen and then use the UP/DOWN arrows to select the desired function, then press the MENU/SEL button to return to the Main Window. Press the Side Button Setup Switch or select Button on the main menu. Side Button Setup Switch Gain Freq. Button Rolloff The button menu provides a scrollable list of the available functions. Us the UP/DOWN arrows to highlight the desired function and press BACK or MENU/SEL to select it and return to the main menu. Talkback is a “push to talk” function Button that is active only while the button is pressed. The talkback function TalkBk provides a communication channel when used with a receiver equipped with this function, such as a Venue Wideband receiver with irmware Ver. 5.2 or higher. When pressed and held in, the side button re-directs the audio output to a different audio channel on the receiver. As soon as the switch is released, audio is returned to the program channel. NOTE: The Talkback function is only available in the Digital Hybrid compatibility mode. An error message will appear if Talkback is selected while in another mode. Button Power Power turns the power on and off. Hold the button in until the countdown sequence from 3 to 1 is completed. The power will then be turned off. Cough is a momentary mute switch. Audio is muted while the button is held in. Button NOTE: The Power and Cough functions were added starting with serial number 1001. Mute is a “push on/push” off function that toggles on and off each time the Side Button is pressed. The mute function defeats the audio in the transmitter, so it works in all compatibility modes and with all receivers. (none) disables the switch. Button (none) For detailed information on setting up the Talkback function and the Venue receiver, refer to the Installation Guide for the Venue Wideband Receiver. Main Window Displays for Mute and Talkback Functions The function of the Side Button is displayed in the LCD Main Window. 5A 5A TB 5A 623.400 623.400 623.400 -40 -20 -40 None/Power -20 Talkback -40 MUTE -20 Mute/Cough When the Side Button is pressed, the function will be active and the LCD will display an indication. Reverse video Reverse video 5A TB 5A 623.400 623.400 -40 -20 Talkback active MUTE <–MUTE–> Mute active (MUTE blinks) (additional information on page 7) Rio Rancho, NM 11 HHa Mic Capsule Adjustments (EXPERT LEVEL ADJUSTMENT) Resonance tuned suspension HHVMC capsule These adjustments signiicantly alter the gain and tonal quality of the microphone, and are to be used only in special circumstances. Caution: Always make the final decision about sound quality with the windscreen in place. Remove the windscreen using the supplied wrench. Attenuator control EQ controls (HHVMC only) Align lats on the wrench with lats on the capsule. IMPORTANT: Be sure to set the attenuator control back to its original setting (“F”) for normal operation. or a subsequent user may think the unit is malfunctioning or has a poor signal to noise ratio. Attenuator Adjustment The HHC & HHVMC heads include an attenuator in the preamp circuitry to provide an additional 15 dB of headroom when needed for extremely loud voices. The attenuator should ONLY be used when the gain control is already turned all the way down and the audio is still driving the preamp into signiicant limiting where both -20 and -10 dB LEDs stay lit all or most of the time during peaks in the audio. LO/MID/HI (bass/mid/treble) - HHVMC only The HHVMC head includes VariMicTM equalization adjustments to boost or cut the frequency response in LOW, MID and HIGH ranges. The LOW and HIGH controls will boost/cut by up to 8 dB while the MID control will boost/cut up to 6 dB. The pointer is between the darkened dots. Gain -40 -20 Gain set to minimum (0) on the LCD. LOW LEDs on control panel The attenuator control is a 16 position switch that attenuates the audio in 1 dB steps. It is marked 0 through F where F is minimum attenuation and 0 is maximum attenuation. Rotating it clockwise increases the loudness, and counter clockwise decreases the loudness. MID HIGH The controls are set to “zero” (no boost or cut) in this photo These controls operate as standard tone controls in that a counterclockwise adjustment cuts the response in that band and a clockwise adjustment boosts the response. VariMic Tone Control Range +10 Boost Attenuator switch set at F for normal operation. Treble Bass Midrange Bass Midrange +5 0dB -5 Treble Cut -10 12 10Hz 100Hz 1KHz 10KHz LECTROSONICS, INC. Wideband Hand Held Transmitter Firmware Updates As of the date of this writing, the irmware update program runs only on a Windows operating system. Updating the irmware is simply a matter of downloading a utility program and ile from the web site and running the program with the receiver connected to a computer via the USB port. Go to www.lectrosonics.com/US. Click on SUPPORT in the top bar, then click on the link to the HHa transmitter in the CATEGORIES pane on the right side of the page. Click on the link labeled Firmware Updates at the bottom of the page. Download the Firmware Updater program zip ile and extract it to a temporary folder on your computer. Then download and extract the irmware zip ile (e.g. xxxx_16.zip) and extract it to a temporary folder on your computer. Remove the lower housing of the transmitter by unscrewing it from the housing attached to the capsule and pulling it straight off the body of the transmitter to expose the circuitry. Spring-loaded ball detents provide a “stop” with only the control panel exposed. Continue to pull the lower housing farther to remove it. Simply push the lower housing back onto the transmitter body to re-install it. Hold down the BACK and UP arrow buttons on the transmitter control panel while powering it up. The LCD will display UPDATE to conirm it is in this mode. UPDATE Connect the USB cable and run the utility program. The program will automatically detect the transmitter and prompt for the location of the irmware ile. Point at the ile and click on Start. The process takes about 90 seconds. A message on the computer screen will conirm the update is complete. Turn the transmitter off and disconnect the USB cable. Turn the transmitter back on again in the normal mode to verify it is working correctly. The USB port on the transmitter requires a micro-B male plug on the connecting cable. The other end of the cable would normally be a USB A-Type male connector to it the most common type of USB jack used on computers. Opening in clear plastic sleeve USB Port Rio Rancho, NM Spring-loaded balls engage detents in housing 13 HHa Parts and Accessories #55008 - Blue Battery Caddy HHXTND Extender to for use with microphone lags commonly used in ENG for network or station ID to keep the lag from covering the side switch and LCD HH2SEN Adapter #CCHH - Zippered Pouch Adapts Sennheiser G2, G3 and 2000 Series microphone capsule heads to the HH transmitter. Transmitter interface Capsule interface Padded zipper pouch for handheld transmitter HHA Adapter by Ambient Recording #26872 Mic Capsule Wrench Custom wrench for removing windscreen from mic capsule Adapts Neumann KK104 and KK105 and Sennheiser capsules for the 5000 Series wireless with Shure style threads to the HH transmitter HHA is available from Ambient Recording dealers Visit: www.ambient.de #13585 Mic Clip Screw on mic clip for standard mic stands with 5/8”-27 thread 14 LECTROSONICS, INC. Wideband Hand Held Transmitter Troubleshooting SYMPTOM POSSIBLE CAUSE TRANSMITTER WILL NOT POWER ON 1) Batteries are inserted backwards. 2) Batteries are dead, or too low to be used. HH MODULATION LEDs OFF 1) Audio Gain set too low. 2) Battery is inserted backwards. Check LCD for power indication. 3) Mic capsule is damaged or malfunctioning. Contact the factory for repair. HH MODULATION LEDs GOOD BUT NO SOUND 1) Talkback function is engaged (release multi-function button). See p. 11. 2) Receiver on wrong frequency or wrong block. 3) Receiver connected incorrectly to sound system. 4) Transmitter in standby mode. RECEIVER RF INDICATOR OFF 1) Transmitter not turned on. 2) Transmitter is in “standby” (non-transmitting) mode. Check the LCD for the antenna/transmission icon status. 3) Batteries are dead or installed backwards. 4) Receiver antenna missing, defective or improperly positioned. 5) Transmitter and receiver not on same frequency block. Check labels on transmitter and receiver to be sure they are operating on the same frequency block. 6) Make sure the transmitter and receiver frequency settings are in agreement. 7) Operating range is too great. 8) Receiver antenna missing, incorrect frequency or disconnected. NO SOUND BUT RECEIVER AUDIO LEVEL METER INDICATES SOUND 1) Receiver audio is muted. (Unmute receiver.) 2) Receiver audio output levels set too low. 3) Receiver audio output is disconnected or cable defective or mis-wired. 4) Sound system or recorder input level is turned down. DISTORTED SOUND 1) Transmitter Audio Gain set too high. Speak or sing into the transmitter and check the Audio Level LEDs, Audio Level bar graph in the transmitter LCD and corresponding indicators on the receiver. 2) Receiver output level may be too high for the sound system or recorder input. 3) Excessive wind noise or “breath pops.” Microphone may require an additional wind screen. 4) Transmitter frequency setting is not correct (when used with non-Digital Hybrid receiver). 5) Compatibility Mode mismatch between transmitter and receiver. 6) Mic capsule damaged or defective HISS AND NOISE -- AUDIBLE DROPOUTS 1) Transmitter Audio Gain set too low. See page 10 for proper audio gain setting. 2) Receiver antenna missing, defective or obstructed. 3) Operating range too great. 4) Interference may be present. Turn transmitter off and observe the RF level indicator on the receiver. Change frequency if necessary. 5) Return attenuator control back to default setting of “F”, then readjust audio gain per instructions on page 10 EXCESSIVE FEEDBACK 1) Transmitter Audio Gain set too high. Check level adjustment, reduce receiver output level, or both. 2) Microphone too close to speaker system. 3) Move microphone closer to the user’s mouth and lower the sound system volume. Rio Rancho, NM 15 HHa Specifications Operating frequencies: † Band A1: 470.100 - 537.575 Band B1: 537.600 - 614.375 Band C1: 614.400 - 691.175 Band D1: 691.200 - 767.975 (export only) Channel Step Size: Normal Tuning mode: Fine Tuning mode: RF Power output: Pilot tone: Frequency stability: Deviation: Spurious radiation: Operating temperature range: Input compressor: Audio Gain range: Modulation indicators: Frequency response Low frequency roll-off: Controls: External: Internal control panel: Battery: Battery Life: Battery Status Indication: Capsule Interface: Capsule Power available: Input impedance: Weight: Dimensions: Emission Designator: 100 kHz 25 kHz Selectable at 50 or 100 mW 25 to 32 kHz frequency; 5 kHz deviation (Hybrid, IFB, 200 Series, Mode 6) ± 0.002% ± 75 kHz max. (Digital Hybrid mode) 90 dB below carrier -20° C to +50° C Dual envelope compressor, >30 dB range 0 to 45 dB; menu selectable Dual bicolor LEDs indicate modulation of -20, -10, 0 and +10 dB referenced to full modulation, LCD bar-graph indicator 40 Hz to 20 kHz (+/- 1dB) -3 dB selectable @35, 50, 70, 100, 125 Hz, 36 dB/octave (varies slightly w/ selection) Programmable mute/talkback button Power, Side Button Setup, MENU/SEL, BACK and Up/Down arrow buttons for menu item selection and settings. (2) AA with polarity protection and battery ejection lever 5.5 hours (alkaline); 8-10 hours (lithium) Transmitted to Lectrosonics Digital Hybrid and 200 Series receivers 1.25 in. diameter x 28 thread pitch 5V, 25 mA max 1000 Ohms 11.4 oz. with lithium batteries and HHC capsule 9.5” long x 1.97” diameter at largest point with HHC capsule attached 180KF3E Specifications subject to change without notice. † Not all frequency blocks are available in all countries. Consult your local representative or contact Lectrosonics for more information. 16 LECTROSONICS, INC. Wideband Hand Held Transmitter FCC Compliance: This device complies with FCC radiation exposure limits as set forth for an uncontrolled environment. This device should be installed and operated so that its antenna(s) are not co-located or operating in conjunction with any other antenna or transmitter. Notice to the End User: The normal condition of using this device is to keep the hand at least 20mm away from the base of the microphone. Industry Canada Compliance: This device operates on a no-protection no-interference basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio license is required. Please consult Industry Canada’s document CPC-2-1-28, Optional Licensing for Low-Power Radio Apparatus in the TV Bands, for details. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference; 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Cet appareil est conforme à Industrie Canada une licence standard RSS exonérés (s). Son fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne doit pas provoquer d’interférences 2. Cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant provoquer un fonctionnement indésirable de l’appareil Rio Rancho, NM 17 HHa Service and Repair If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the Troubleshooting section in this manual. We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop attempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connection, send the unit to the factory for repair and service. Don’t attempt to adjust any controls inside the units. Once set at the factory, the various controls and trimmers do not drift with age or vibration and never require readjustment. There are no adjustments inside that will make a malfunctioning unit start working. LECTROSONICS’ Service Department is equipped and staffed to quickly repair your equipment. In-warranty repairs are made at no charge in accordance with the terms of the warranty. Out-of-warranty repairs are charged at a modest lat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone for out-of-warranty repairs. Returning Units for Repair For timely service, please follow the steps below: A. DO NOT return equipment to the factory for repair without irst contacting us by letter or by phone. We need to know the nature of the problem, the model number and the serial number of the equipment. We also need a phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time). B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed your repair through our receiving and repair departments. The return authorization number must be clearly shown on the outside of the shipping container. C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the proper packing materials. UPS is usually the best way to ship the units. Heavy units should be “double-boxed” for safe transport. D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or damage to equipment that you ship. Of course, we insure the equipment when we ship it back to you. Mailing address: Lectrosonics, Inc. PO Box 15900 Rio Rancho, NM 87174 USA Shipping address: Lectrosonics, Inc. 581 Laser Rd. Rio Rancho, NM 87124 USA Web: www.lectrosonics.com E-mail: sales@lectrosonics.com Telephone: (505) 892-4501 (800) 821-1121 Toll-free (505) 892-6243 Fax Lectrosonics Canada: Mailing Address: 720 Spadina Avenue, Suite 600 Toronto, Ontario M5S 2T9 18 Telephone: (416) 596-2202 (877) 753-2876 Toll-free (877-7LECTRO) (416) 596-6648 Fax E-mail: Sales: colinb@lectrosonics.com Service: joeb@lectrosonics.com LECTROSONICS, INC. Wideband Hand Held Transmitter Rio Rancho, NM 19 LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot correct the defect in your equipment, it will be replaced at no charge with a similar new item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you. This warranty applies only to items returned to Lectrosonics, Inc. or an authorized dealer, shipping costs prepaid, within one year from the date of purchase. This Limited Warranty is governed by the laws of the State of New Mexico. It states the entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT. This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state. 581 Laser Road NE • Rio Rancho, NM 87124 USA • www.lectrosonics.com (505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.com 20 23 October 2015
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Create Date : 2015:10:23 10:25:03-06:00 Creator : Adobe InDesign CC 2015 (Windows) Modify Date : 2015:10:24 09:18:37-07:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Instance ID : uuid:70094543-6899-42bb-b519-833cfec1f129 Original Document ID : adobe:docid:indd:1d6baa05-eea2-11db-999c-8f25222bbf24 Document ID : xmp.id:313c1d72-d11c-304f-93d5-506d9f3120c2 Rendition Class : proof:pdf Version ID : 1 Derived From Instance ID : xmp.iid:ea3c7102-c525-9742-ab98-180ab6eff127 Derived From Document ID : xmp.did:57371cbe-fd35-2949-a7ec-e0fcd40c86ed Derived From Original Document ID: adobe:docid:indd:1d6baa05-eea2-11db-999c-8f25222bbf24 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2015 (Windows) History Changed : / History When : 2015:10:23 10:25:03-06:00 Metadata Date : 2015:10:24 09:18:37-07:00 Creator Tool : Adobe InDesign CC 2015 (Windows) Format : application/pdf Title : HHa_man.indd Producer : Adobe PDF Library 15.0 Trapped : False GTS PDFX Version : PDF/X-4 Page Count : 20EXIF Metadata provided by EXIF.tools