Lectrosonics HMAC1 Wireless Microphone Transmitter User Manual hma man indd
Lectrosonics Inc Wireless Microphone Transmitter hma man indd
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2939710 |
| Application ID | RXdAChnsx3Rmb0uNkeXJ4w== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 273.66kB (3420771 bits) |
| Date Submitted | 2016-03-23 00:00:00 |
| Date Available | 2016-03-23 00:00:00 |
| Creation Date | 2017-11-21 23:14:19 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-11-21 23:14:19 |
| Document Title | hma_man.indd |
| Document Creator | Adobe InDesign CC 2015 (Windows) |
INSTRUCTION MANUAL HMa Wideband Plug-On Transmitter With Digital Hybrid Wireless® Technology Digital Hybrid Wireless® US Patent 7,225,135 Fill in for your records: Serial Number: Purchase Date: Rio Rancho, NM, USA www.lectrosonics.com HMa LECTROSONICS, INC. Wideband Digital Hybrid® Plug-On Transmitter Thank you for selecting a Lectrosonics HMa plug-On transmitter. The unique design provides several distinct features for professional applications: • Outstanding RF operating range • Superb audio quality • Corrosion-resistant housing • Programmable compatibility modes for use with a wide variety of different receivers The Digital Hybrid Wireless® design (US Patent 7,225,135) combines 24-bit digital audio with analog FM resulting in a system that has the same operating range as analog systems, the same spectral eficiency as analog systems, the same long battery life as analog systems, plus the excellent audio idelity typical of pure digital systems. The transmitter uses a standard 3-pin XLR input jack for use with any microphone with a a mating XLR connector. An LCD, membrane switches and multi-color LEDs on the control panel make input gain adjustments and frequency and compatibility mode selection quick and accurate, without having to view the receiver. The housing is machined from a solid aluminum block to provide a lightweight and rugged package. A special non-corrosive inish resists salt water exposure and perspiration in extreme environments. The DSP-based design works with all Digital Hybrid receivers, and is backward compatible for use with Lectrosonics 200 and 100 Series and IFB receivers and some other brands of analog wireless receivers. Companion receivers are covered in separate manuals. Table of Contents General Technical Description ...............................................4 Wideband Design...................................................................4 Digital Hybrid Wireless® Technology ......................................4 No Pre-Emphasis/De-Emphasis ............................................4 Low Frequency Roll-Off .........................................................4 Input Limiter ...........................................................................5 Signal Encoding and Pilot Tone .............................................5 Microprocessor and DSP .......................................................5 Compatibility Modes...............................................................5 Control Panel .........................................................................5 Battery Options and Operating Time .....................................5 Frequency Blocks and Bands ................................................5 Controls and Functions ..........................................................6 LCD Screen ...........................................................................6 Power LED .............................................................................6 Audio Input Jack.....................................................................6 Battery Compartment.............................................................6 Modulation LEDs....................................................................6 Audio Button ..........................................................................6 Up/Down Arrows and Panel Lockout......................................6 Antenna..................................................................................6 Battery Installation ..................................................................7 Attaching/Removing a Microphone .......................................7 Operating Instructions ............................................................8 Power Up and Boot Sequence ...............................................8 Power Down ...........................................................................8 Automatic Power Restore.......................................................8 Standby Mode ........................................................................8 Compatibility Mode Screen ....................................................8 Selecting the Audio Polarity ...................................................8 LCD Backlight Settings ..........................................................9 Selecting Step Size mode ......................................................9 Setting Transmitter Operating Frequency...............................9 Lock/Unlock Screen ...............................................................9 Audio Screen .......................................................................10 Adjusting the Input Gain.......................................................10 Adjusting the Low Frequency Roll-off ..................................10 Selecting the Phantom Power Supply ..................................10 About the Phantom Power Supply .......................................11 Special Purpose Barrel Adapters .........................................12 MCA-M30 .............................................................................12 Accessories ...........................................................................13 Troubleshooting.....................................................................14 Specifications and Features .................................................16 Service and Repair ................................................................17 Returning Units for Repair ...................................................17 Consumer Alert for US Users - FCC Order DA 10-92 Most users do not need a license to operate this wireless microphone system. Nevertheless, operating this microphone system without a license is subject to certain restrictions: the system may not cause harmful interference; it must operate at a low power level (not in excess of 50 milliwatts); and it has no protection from interference received from any other device. Purchasers should also be aware that the FCC is currently evaluating use of wireless microphone systems, and these rules are subject to change. For more information, call the FCC at 1-888- CALL-FCC (TTY: 1-888-TELL-FCC) or visit the FCC’s wireless microphone website at www.fcc.gov/cgb/wirelessmicrophones. To operate wireless microphone systems at power greater than 50mW, you must qualify as a Part 74 user and be licensed. If you qualify and wish to apply for a license go to: http://www.fcc.gov/Forms/Form601/601.html Rio Rancho, NM HMa General Technical Description Wideband Design channel as eficiently and robustly as possible, yielding audio performance that rivals that of wholly digital systems, without the power and bandwidth problems inherent in digital transmission. The HMa transmitter uses ±75 kHz wide deviation for an excellent signal to noise ratio and wide dynamic range. The DSP controlled input limiter features a wide range dual envelope design which cleanly limits input signal peaks over 30 dB above full modulation. Switching power supplies to provide constant voltages to the transmitter circuits from the beginning (3 Volts) to the end (1.7 Volts) of battery life, and an ultra low noise input ampliier for quiet operation. Because it uses an analog FM link, Digital Hybrid Wireless® enjoys all the beneits of conventional FM wireless systems, such as excellent range, eficient use of RF spectrum, and resistance to interference. However, unlike conventional FM systems, it does away with the analog compandor and its artifacts. Digital Hybrid Wireless® Technology No Pre-Emphasis/De-Emphasis All wireless links suffer from channel noise to some degree, and all wireless microphone systems seek to minimize the impact of that noise on the desired signal. Conventional analog systems use compandors for enhanced dynamic range, at the cost of subtle artifacts (known as “pumping” and “breathing”). Wholly digital systems defeat the noise by sending the audio information in digital form, at the cost of some combination of power, bandwidth and resistance to interference. The Digital Hybrid Wireless® design results in a signal-tonoise ratio high enough to preclude the need for conventional pre-emphasis (HF boost) in the transmitter and de-emphasis (HF roll-off) in the receiver. This eliminates the potential for extreme distortion on signals with abundant high-frequency information. Low Frequency Roll-Off Lectrosonics Digital Hybrid Wireless® systems overcome channel noise in a dramatically new way, digitally encoding the audio in the transmitter and decoding it in the receiver, yet still sending the encoded information via an analog FM wireless link. This proprietary algorithm is not a digital implementation of an analog compandor but a technique that can be accomplished only in the digital domain, even though the inputs and outputs are analog. The low frequency roll-off can be set for a 3 dB down point at 35, 50 or 70 Hz to control subsonic and very low frequency audio content in the audio. The actual roll-off frequency will vary slightly depending upon the low frequency response of the microphone. Excessive low frequency content can drive the transmitter into limiting, or in the case of high level sound systems, can even cause damage to loudspeaker systems. The roll-off is normally adjusted by ear while listening as the system is operating. Channel noise still impacts received signal quality and will eventually overwhelm a receiver. Digital Hybrid Wireless® simply encodes the signal to use a noisy Bias Voltage 42V,15V, 5V Phantom Power Input Amp Digital Pot +4V Hi.Lo Pass Filter Audio A-D Converter 11001001 D-A Converter Encoded Audio and Pilot Tone Filter Amp 11001001 Audio Level 1.2V Digital Signal Processor 4V Shunt Limiter 3V Battery Switching Power Supply -3.3V +3.3V Microprocessor Reference Crystal LCD FREQ UP DWN Bicolor Modulation LEDs Control Panel AUDIO Phase Locked Loop Reference Crystal Voltage Controlled Oscillator Final Amplifier LECTROSONICS, INC. Wideband Digital Hybrid® Plug-On Transmitter Input Limiter A DSP-controlled analog audio limiter is employed before the analog-to-digital (A-D) converter. The limiter has a range of more than 30 dB for excellent overload protection. A dual release envelope makes the limiter acoustically transparent while maintaining low distortion. It can be thought of as two limiters in series, a fast attack and release limiter followed by a slow attack and release limiter. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels, to keep audio distortion low and while preserving short term dynamics. Signal Encoding and Pilot Tone In addition to controlling the limiter, the DSP also encodes the digitized audio from the A-D converter and adds an ultrasonic pilot tone to control the receiver’s squelch. A pilot tone squelch system provides a reliable method of keeping a receiver output muted (squelched) even in the presence of signiicant interference. When the system is operating in the hybrid mode, a different pilot tone frequency is generated for each carrier frequency to prevent inadvertent squelch problems and simplify multi-channel coordination. Microprocessor and DSP A microprocessor monitors user command inputs from the control panel buttons and numerous other internal signals. It works intimately with the DSP to ensure the audio is encoded according to the selected Compatibility Mode and that the correct pilot tone is added to the encoded signal. Control Panel The control panel includes four membrane switches and an LCD screen to adjust the operational settings. Multicolor LEDs are used to indicate audio signal levels for accurate gain adjustment and for battery status. Battery Options and Operating Time Switching power supplies convert battery voltages to operate various circuit stages with maximum eficiency. Frequency Blocks and Bands Lectrosonics established a “block” numbering system years ago to organize the range of frequencies available from the low 500 MHz band to the upper 700 MHz band. Each block includes 256 frequencies in 100 kHz increments. The block number is part of a simple formula to derive the frequency. The block number is multiplied by 25.6 to produce the lowest frequency in the block. For example, block 27 x 25.6 = 691.200. The HMa transmitter features a wideband tuning range that covers three blocks. This tuning range is referred to as a BAND rather than a block. Band Tuning Range (MHz) A1 170.100 - 534.575 B1 537.600 - 614.375 C1 614.400 - 691.175 *C1 will not be in use after the results of the next DTV transition spectrum auction in 2016 are in full effect. Compatibility Modes The transmitter was designed to operate with Lectrosonics Digital Hybrid Wirteless® receivers and will yield the best performance when doing so. However, due to the lexibility of digital signal processing, the transmitters can also operate in various compatibility modes for use with Lectrosonics 100 and 200 Series and IFB receivers. It will also work with certain non-Lectrosonics receivers. Contact your sales representative or the factory for a complete list of compatible non-Lectrosonics receivers. Rio Rancho, NM HMa Controls and Functions Input Coupler Modulation LEDs LCD UP Arrow Battery Compartment Modulation LEDs The Modulation LEDs provide a visual indication of the input audio signal level from the microphone. These two bicolor LEDs can glow either red or green to indicate modulation levels. Full modulation (0 dB) occurs when the -20 LED irst turns red. Signal Level XLR Input Jack PWR LED AUDIO Button FREQ Button DOWN Arrow LCD Screen The LCD is a numeric-type Liquid Crystal Display with several screens that allow settings to be made with the AUDIO, FREQ, UP and DOWN buttons to conigure the transmitter. The transmitter can be turned on in a Standby mode to make adjustments without the risk of interfering with other wireless systems nearby. Counters are presented on the LCD enabling this function. Power LED The PWR LED glows green when the batteries are good. The color changes to red when there is about 20 minutes of life left. When the LED begins to blink red, there are only a few minutes of life. A weak battery will sometimes cause the PWR LED to glow green immediately after being put into the unit, but will soon discharge to the point where the LED will go red or shut off completely. Audio Input Jack The XLR input jack on the transmitter accommodates most hand-held microphones. Phantom power can be set at various levels for use with a wide variety of electret microphones. Battery Compartment The battery compartment door is made of machined aluminum and is hinged to the housing to prevent it being damaged or lost. -20 LED -10 LED Less than -20 dB Off Off -20 dB to -10 dB Green Off -10 dB to +0 dB Green Green +0 dB to +10 dB Red Green Greater than +10 dB Red Red Audio Button The AUDIO button is used to display the audio level setting, low frequency roll-off and phantom power mode. Repeatedly pressing the button will cycle through the available settings, allowing the UP and DOWN arrow buttons to adjust the values. Freq Button The FREQ Button displays the selected operating frequency and also toggles the LCD between displaying the actual operating frequency in MHz and a two-digit hexadecimal number. Frequencies can be selected in either 100kHz or 25kHz steps. The appearance of the hexadecimal number is different in the 100kHz step size mode than in the 25kHz step size mode. NOTE: The FREQ and AUDIO buttons are used together to enter the standby mode and to turn the power on or off. Up/Down Arrows and Panel Lockout The Up and Down arrow buttons are used to select the operating frequency, adjust the audio level, or set the Compatibility Mode. Pressing both arrows simultaneously enters the lock countdown. Holding the two buttons in until the countdown is completed locks the control panel buttons so they can only be used to display current settings. “Loc” is displayed to indicate the controls are locked when a button is pressed while the panel is locked. Once locked, the buttons are unlocked by removing the battery. Antenna An antenna is formed between the housing and the attached microphone, operating much like a dipole type. At UHF frequencies the length of the housing is similar to 1/4 wavelength of the operating frequency, so the antenna is surprisingly eficient, which helps extend the operating range and suppress noise and interference. LECTROSONICS, INC. Wideband Digital Hybrid® Plug-On Transmitter Battery Installation The transmitter is powered by two AA batteries. Note: Standard zinc-carbon batteries marked “heavy-duty” or “long-lasting” are not adequate. Attaching/Removing a Microphone The spring loaded coupler under the XLR jack maintains a secure it to the microphone jack with continuous pressure applied by an internal spring. To attach the microphone, simply align the XLR pins and press the microphone onto the transmitter until the coupler retracts and latches. A click sound will be heard as the connector latches. To remove the microphone, hold the transmitter body in one hand with the microphone pointing upward. Use your other hand to rotate the coupler until the latch releases and the coupler rises slightly. TO ATTACH TO REMOVE Press firmly, listen for click. Depress collar fully. Batteries operate in series, with a connecting plate built into the battery door Click! Hold the transmitter case with the microphone pointed upward. Rotate the collar in the direction shown. To install new batteries: 1. Slide open the Battery Cover and remove any old batteries. 2. Insert the new batteries into the housing. One battery goes in positive (+) end irst, the other negative (-) end irst. Look into the battery compartment to determine which end goes in which side. The side with the plastic ring is the side which accepts the positive end of the battery. positive (+) terminal Pull on mic to ensure it is locked. NOTE: Do not hold or apply any pressure to the microphone body while trying to remove it, as this may prevent the latch from releasing. negative (–) terminal Note: It is possible to install the batteries backward and close the battery door, but the batteries will not make contact and the unit will not work. 3. Slide the Battery Cover until it snaps securely shut. Rio Rancho, NM HMa Operating Instructions Modulation LEDs UP Arrow PWR LED Automatic Power Restore The irmware will remember the power on/off state and the settings when batteries reach their end of life or are removed. When fresh batteries are installed, the unit will reboot and return to the previous settings without the need to press any buttons. This only works when the unit is fully on and transmitting. It does not work in the Standby Mode. Standby Mode AUDIO Button FREQ Button DOWN Arrow Power Up and Boot Sequence 1) Ensure that good batteries are installed in the unit. 2) Simultaneously press and hold the AUDIO and FREQ buttons. Continue holding the buttons until On and the characters 1, 2, 3 have appeared. The boot sequence will then initiate. Initial Power On Timer Screen As the unit turns on, the Modulation LEDs and PWR LED all glow red, then green, and then they revert to normal operation. The LCD displays a bootup sequence which consists of four screens: Company Name: Lectro Frequency Band (XX) and Firmware Version (rX.X): b21r1.1 (typ) Compatibility Mode: CP 400 (typ) Audio: Aud 12 (typ) Power Down Simultaneously press and hold the AUDIO and FREQ buttons. Continue holding the buttons until OFF and the countdown characters 3, 2, 1 have appeared. The unit will then power down. If the AUDIO and FREQ buttons are released before the LCD goes blank at the end Initial Power Off of the countdown, the unit will Timer Screen not turn off. Instead, it will stay on and the LCD will return to the previous screen. NOTE: If batteries are removed or reach the end of life while the unit is turned on, the unit will turn back on with a brief, simultaneous press of the AUDIO and FREQ buttons. The counting sequence will not be displayed in this instance. Standby Mode allows you to verify or change the transmitter’s operating frequency Standby Screen or audio input level without transmitting a signal. Quickly press and release both the AUDIO and FREQ buttons simultaneously to enter and exit this mode. The characters rF OFF will appear on the LCD while the unit is in the standby mode. Compatibility Mode Screen Hold down the UP arrow button while powering up the unit to enter the Compatibility Mode screen. Use the UP or DOWN arrow buttons to select one of six compatibility modes: Note: RF transmission is prevented while selecting Compatibility Modes. Also, the HM exits this screen to the Standby Mode. 400 - For Digital Hybrid Wireless® receivers. 200 - For Lectrosonics 200 Series receivers. 100 - For Lectrosonics 100 Series receivers. 3 - (Mode 3) For non-Lectrosonics analog receivers. Contact the the factory for details. • IFB - For Lectrosonics IFB receivers. • 6 - (Mode 6) For non-Lectrosonics analog receivers. Contact the factory for details. • 7 - (Mode 7) For non-Lectrosonics analog receivers. Contact the factory for details. While in the compatibility mode screen, pressing either the AUDIO or FREQ button exits to standby mode. To power off from the compatibility mode screen, press and hold AUDIO and FREQ together. • • • • Selecting the Audio Polarity Hold the UP arrow in and press the AUDIO and FREQ buttons together to enter the setup mode. The display will irst enter the CP (compatibility mode) setup screen. The character P denotes “positive” polarity and the character n denotes “negative” polarity. Press the AUDIO or FREQ button to enter the AP (audio polarity) setup screen. Use the UP and DOWN arrows to select the desired polarity. NOTE: The audio polarity can also be reversed at the output of most Lectrosonics receivers. LECTROSONICS, INC. Wideband Digital Hybrid® Plug-On Transmitter LCD Backlight Settings The LCD backlight can be set to turn off after either 5 minutes or 30 seconds or stay on continuously. Hold the UP arrow in while powering up the unit to enter the setup screen. Press the AUDIO button repeatedly to step through the setup items to reach the backlight settings screen. Use the UP or DOWN arrow button to select the desired setting. Set Up in 100kHz Mode Frequency displayed in MHz Frequency displayed as two-digit hexadecimal number The operating frequency can be displayed either in MHz or as a two-digit hexadecimal number. The example of the two-digit display shown here indicates CH (channel) and 2C as the frequency. The frequency can be set with the unit in standby mode or when powered up for normal operation. Set Up in 25kHz Mode Selecting Step Size mode The hexadecimal display in the 25 kHz mode will appear with a decimal sufix to indicate the 25 kHz steps. The frequency increments can be set at either 25 kHz or 100 kHz. Hold the UP arrow in while powering up the unit to enter the setup screen. Press the AUDIO button repeatedly to step through the setup items to reach the Step Size Mode screen. Use the UP or DOWN arrow button to select the desired setting. 644.400 MHz 644.425 MHz 644.450 MHz 644.475 MHz Lock/Unlock Screen Setting Transmitter Operating Frequency 1) If the LCD is displaying something other than the Frequency Screen, press the FREQ button on the Control Panel to enter this screen. Simultaneously pressing and holding both the UP and DOWN arrow buttons during normal operation starts the Lock timer. The timer starts at three and counts down to zero. When the timer reaches zero, the keypad controls are locked. Note: The default display is in MHz. Pressing the FREQ button again displays the operating frequency as a two-digit hexadecimal number that corresponds to legacy Lectrosonics products that used two 16-position switches to set the frequency. 2) While holding the FREQ button, use the UP or DOWN arrow buttons to move the operating frequency up or down. Note: The operating frequency displayed on the LCD wraps as it reaches the upper or lower end of its range. Thus, if you intend to move the operating frequency from the lower end of the range to the upper end, it may be faster to do this by using the DOWN arrow until the frequency wraps to the upper end. The LCD will display the locked condition as long as the arrow buttons are held, then revert back to the previous screen when either button is released. With the controls locked, the AUDIO and FREQ buttons can still be used to display current settings. Any attempt to change a setting by pressing either the UP or DOWN arrow button will result in an on-screen Loc reminder that the controls are locked. Remove the batteries to unlock the control panel. Important: Once the transmitter is locked, it cannot be unlocked or powered off using the buttons. The only way to unlock a locked transmitter is to remove the batteries. Rio Rancho, NM HMa Audio Screen The Audio Screen is used to adjust input gain and low frequency roll-off, and to turn phantom power on and off. Repeatedly pressing the AUDIO button selects the setting. Press and hold the AUDIO button and use the UP and DOWN arrows to adjust the value. 5) If the unit was set up in Standby Mode, it will be necessary to turn the transmitter off, then power it up again in normal operation so the RF output will be on. Then the other components in the sound or recording system can be adjusted. Adjusting the Low Frequency Roll-off Repeatedly press the AUDIO button until the LF rolloff adjustment screen appears. Then press and hold the AUDIO button while selecting the desired roll-off frequency with the UP and DOWN arrows. Adjusting the Input Gain The control panel Modulation LEDs indicate the modulation level and limiter activity. This gain adjustment matches the transmitter gain with the microphone’s output level, the user’s voice level and the position of the microphone. Once set, the transmitter’s audio level setting should not be used to control the volume of your sound system or recorder levels. The audio input level can be set with the unit in Standby Mode or while powered up in normal operation. Signal Level -20 LED -10 LED Less than -20 dB Off Off -20 dB to -10 dB Green Off -10 dB to +0 dB Green Green +0 dB to +10 dB Red Green Greater than +10 dB Red Red Note: Voice levels vary signiicantly between different people. If several different people will be using the transmitter and there is not time to make the adjustment for each individual, adjust it for the loudest voice. 1) With the HMa powered off, insert the microphone plug into the XLR Input Jack, aligning the pins and ensuring that the connector locks. 2) Place the transmitter in the Standby Mode, or if the unit is to be powered up and adjusted, mute the main sound system prior to powering up the transmitter. 3) Position the microphone in the location where it will be used in actual operation. The roll-off frequency can be set to 35, 50 or 70 Hz. Selecting the Phantom Power Supply The transmitter input jack can provide phantom power for the attached microphone if needed, with voltages at 5, 15 or 48. Phantom power will consume a slight amount of battery power, so it can also be turned off. With the transmitter powered on and in the normal or standby mode, press and hold the audio button and observe the LCD. Release the button and press and hold it again. Repeat this process until the display indicates the PH. Once you get to the PH setting, keep the AUDIO button pressed, then use the UP and DOWN arrow keys to cycle through the available settings (off, 5, 15, 48 volts) until the desired setting is displayed. When you release the AUDIO button, the setting will be stored to the value you selected. 4) Observe the audio level LEDs while speaking or singing into the microphone at the same voice level that will be used during use. While holding the AUDIO button, press the UP or DOWN arrows until the both the -20 and -10 LEDs glow green, with the -20 LED lickering red on louder peaks. This will optimize the signal to noise ratio of the system with full modulation and adequate headroom to prevent overload and audible compression of signal peaks. Note: Setting the audio level too high reduces the dynamic range of the audio signal. Setting the audio level too low may cause hiss and noise in the audio. 10 LECTROSONICS, INC. Wideband Digital Hybrid® Plug-On Transmitter About the Phantom Power Supply Three phantom voltages are selectable from the control panel. The voltages are: • 5 Volts for lavaliere microphones, • 15 Volts for some professional mics requiring high current and for many common stage mics that will operate over a wide phantom Voltage range of 12 to 48 Volts. With the proper adapter, this position can also be used with T power microphones. See our web site for details on inding or making the proper adapter. • 48 Volts for microphones that do in fact require a supply greater than 18 Volts. (See below for a discussion of why 42 and not a “true” 48 Volts.) For longest battery life use the minimum phantom voltage necessary for the microphone. Many stage microphones regulate the 48 Volts down to 10 Volts internally anyway, so you might as well use the 15 Volt setting and save some battery power. If you are not using a microphone for the input device, or are using a microphone that does not require phantom power, turn the phantom power off. Phantom power should only be used with a fully loating, balanced device such as most microphones with a 3-pin XLR connector. If you use the phantom power with an unbalanced device or if pins 2 or 3 are DC connected to ground, then you will draw maximum current from the power supply. The HM is fully protected against such shorts but the batteries will be drained at twice the normal rate. The transmitter can supply 4 mA at 42 Volts, 8 mA at 15 Volts, and 8 mA at 5 Volts. The 42 Volts setting actually supplies the same voltage to a 48 Volt microphone as the DIN standard arrangement due to a dynamic biasing scheme that does not have as much voltage drop as the DIN standard. The 48 Volt DIN standard arrangement protects against shorts and high fault current with high resistance in the power supply feeds to pins 2 and 3. This provides protection if the supply current is accidentally shorted to ground and also keeps the microphone from being attenuated by the power supply. The HMa improves on those functions and is able to use less power from the battery by using constant current sources and current limiters. With this dynamic arrangement the HMa can also supply more than twice the current of competing 48 Volt plug on units and provide four times the current for some very high end 15 Volt microphones. Rio Rancho, NM 11 HMa Special Purpose Barrel Adapters P/N 21750 Polarity Reversing Barrel Adapter Earthworks M30 Mic adapter for Earthworks M30 microphone with HM, HMa and UH400a/TM transmitters. This polarity reversing adapter may be needed to correct for asymmetrical current draw in some P48 powered condenser microphones, including older Neumann 100 Series, Rode NTG3 and others. If your microphone does not power on correctly when used with these transmitters, insert the adapter between the transmitter and microphone. Barrel Adapter MCA-M30 This adapter may be needed if you are experiencing noise or distortion with measurement microphones, particularly the Earthworks M30. The adapter has common mode checks for suppressing RF noise. If your microphone signal exhibits the problems listed above when connected to a UH400, HM or HMa transmitter, insert the adapter between the microphone and the transmitter. Insert the adapter between the transmitter and microphone to alleviate the problems listed above. 12 LECTROSONICS, INC. Wideband Digital Hybrid® Plug-On Transmitter Accessories PHTRAN3 MCA-TPOWER Replacement leather pouch with clear plastic screen cover, rotating belt clip and snap closure. Included with transmitter at purchase. This cable adapter is to be used with the UH200D, UH400, HM and HMa plug-on transmitters with T-powered microphones. It will protect a T-power mic against the 48V phantom power setting in the transmitter while allowing normal operation. The transmitter should be set to the 15V position for best operation and minimum battery drain. MC5AX Optional adapter for connecting a lavaliere microphone to the HMa or HM transmitters. TA5M to XLR3-M connectors. Passes transmitter phantom power to bias the electret lavaliere microphone. Includes zener protection to limit bias voltage to protect the microphone if transmitter phantom power is set too high. Rio Rancho, NM 13 HMa Troubleshooting Before going through the following chart, be sure that you have good batteries in the transmitter. It is important that you follow these steps in the sequence listed. SYMPTOM POSSIBLE CAUSE TRANSMITTER PWR LED OFF 1) Batteries are inserted backwards or dead. 2) Transmitter not powered up. (See Operating Instructions, Power UP and Boot Sequence.) 1) Gain control set to minimum. 2) Batteries are inserted backwards or dead. Check PWR LED. 3) Mic capsule is damaged or malfunctioning. 4) Mic connector is damaged or mis-wired. AUDIO LEVEL LEDs NOT LIGHTING RECEIVER RF INDICATOR OFF 1) 2) 3) 4) Transmitter not turned on, or is in Standby Mode. Transmitter batteries are dead. Receiver antenna missing or improperly positioned. Transmitter and receiver not on same frequency. Check switches/display on transmitter and receiver. 5) Transmitter and receiver not on same frequency block. 6) Operating range is too great. NO SOUND (OR LOW SOUND LEVEL), RECEIVER INDICATES PROPER AUDIO MODULATION 1) Receiver output level set too low. 2) Receiver output disconnected, or cable defective or mis-wired. 3) Sound system or recorder input is turned down. DISTORTED SOUND 1) Transmitter gain (audio level) is far too high. Check audio level LEDs and receiver audio levels during use. 2) Receiver output may be mismatched with the sound system or recorder input. Adjust output level on receiver to the correct level for the recorder, mixer or sound system. (Use the receiver’s Tone function to check level.) 3) Excessive wind noise or breath “pops.” Reposition microphone and/or use a larger windscreen. 4) Transmitter is not set to same frequency as receiver. Check that operating frequency on receiver and transmitter match. 5) Receiver/Transmitter Compatibility Mode mismatched. EXCESSIVE FEEDBACK 1) Transmitter gain (audio level) too high. Check gain adjustment and/or reduce receiver output level. 2) Talent standing too close to speaker system. 3) Mic is too far from user’s mouth. 14 LECTROSONICS, INC. Wideband Digital Hybrid® Plug-On Transmitter SYMPTOM POSSIBLE CAUSE HISS AND NOISE -- AUDIBLE DROPOUTS 1) 2) 3) 4) Transmitter gain (audio level) far too low. Receiver antenna missing or obstructed. Operating range too great. Signal interference. Turn off transmitter. If receiver’s signal strength indicator does not drop to nearly zero, this indicates an interfering signal may be the problem. Use a clear operating frequency. “Loc” APPEARS IN DISPLAY WHEN ANY BUTTON IS PRESSED 1) Control Panel is locked. (See Operating Instructions, Locking and Unlocking the Control Panel.) “Hold” APPEARS IN DISPLAY WHEN ARROW BUTTONS ARE PRESSED Reminder that it is necessary to hold down the AUDIO or FREQ button to make adjustments to the audio gain or frequency settings. “PLL” APPEARS IN DISPLAY Rio Rancho, NM Indication that the PLL is not locked. This is a serious condition that requires factory repair. It may be possible to operate on another frequency far removed from the one that was selected when the unlocked condition was indicated. 15 HMa Specifications and Features Operating frequencies: (Frequency usage varies by country) Band A1: 470.100 - 537.575 Band B1: 537.600 - 614.375 Band C1: 614.400 - 691.175 Band D1: 691.200 - 767.975 (export only) Channel Step Size: Normal Tuning mode: 100 kHz Fine Tuning mode: 25 kHz Frequency selection: Control panel mounted membrane switches RF Power output: 100 mW (nominal) Compatibility Modes (6) Digital Hybrid Wireless™ (400 Series), 200 Series, 100 Series, analog modes 3, 6, 7 and IFB mode Pilot tone: 25 to 32 kHz; 5 kHz deviation (in Digital Hybrid Mode) Frequency stability: ± 0.002% Deviation: ± 75 kHz max. (in 400 Series Mode) Spurious radiation: 60 dB below carrier Equivalent input noise: –125 dBV, A-weighted Input level: If set for dynamic mic: 0.5 mV to 50 mV before limiting. Greater than 1 V with limiting. If set for electret lavaliere mic: 1.7 uA to 170 uA before limiting. Greater than 5000 uA (5 mA) with limiting. Line level input: 17 mV to 1.7 V before limiting. Greater than 50 V with limiting. Input impedance: 300 Ohms Input limiter: Soft limiter, 30 dB range Gain control range: 55 dB Modulation indicators: Dual bicolor LEDs indicate modulation of –20, -10, 0, +10 dB referenced to full modulation. Controls: Control panel with LCD and four membrane switches. 16 Low frequency roll-off: Audio Frequency Response: Selectable; -3dB at 35, 50 or 70 Hz. 35 Hz to 20 kHz, +/-1 dB (The low frequency roll-off is adjustable) Signal to Noise Ratio (dB): (overall system, 400 Series mode) SmartNR No Limiting w/Limiting OFF 103.5 108.0 NORMAL 107.0 111.5 FULL 108.5 113.0 Total Harmonic Distortion: Audio Input Jack: Phantom Power: Antenna: Batteries:* Battery Life:* Weight: Overall Dimensions: Emission Designator: The dual envelope “soft” limiter provides exceptionally good handling of transients using variable attack and release time constants. The limiter reduces 30 dB of dynamic range into 4.5 dB, which reduces the measured igure for SNR without limiting by 4.5 dB. 0.2% typical (400 Series mode) 3-pin Female XLR • 5V @ 18 mA max. • 15V @ 15 mA max. • 48 V @ 4 mA max. • OFF Housing and attached microphone form the antenna Two 1.5 Volt AA alkaline • AA alkaline; No Phantom: 5h 0m • AA alkaline; 48V Phantom: 3h 30m * Duracell Quantum alkaline 6.7 oz (190 grams) without batteries 4.25x1.62x1.38 inches 180KF3E Speciications subject to change without notice. LECTROSONICS, INC. Wideband Digital Hybrid® Plug-On Transmitter FCC Notice: For body worn operation, this transmitter model has been tested and meets the FCC RF exposure guidelines when used with the Lectrosonics accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Contact Lectrosonics if you have any questions or need more information about RF exposure using this product. FCC Compliance: This device complies with FCC radiation exposure limits as set forth for an uncontrolled environment. This device should be installed and operated so that its antenna(s) are not co-located or operating in conjunction with any other antenna or transmitter. Industry Canada Compliance: This device operates on a no-protection no-interference basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio license is required. Please consult Industry Canada’s document CPC-2-1-28, Optional Licensing for Low-Power Radio Apparatus in the TV Bands, for details. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference; 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Cet appareil est conforme à Industrie Canada une licence standard RSS exonérés (s). Son fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne doit pas provoquer d’interférences 2. Cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant provoquer un fonctionnement indésirable de l’appareil Rio Rancho, NM 17 Service and Repair If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the Troubleshooting section in this manual. We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop attempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connection, send the unit to the factory for repair and service. Don’t attempt to adjust any controls inside the units. Once set at the factory, the various controls and trimmers do not drift with age or vibration and never require readjustment. There are no adjustments inside that will make a malfunctioning unit start working. LECTROSONICS’ Service Department is equipped and staffed to quickly repair your equipment. In warranty repairs are made at no charge in accordance with the terms of the warranty. Out-of-warranty repairs are charged at a modest lat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone for out-of-warranty repairs. Returning Units for Repair For timely service, please follow the steps below: A. DO NOT return equipment to the factory for repair without irst contacting us by email or by phone. We need to know the nature of the problem, the model number and the serial number of the equipment. We also need a phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time). B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed your repair through our receiving and repair departments. The return authorization number must be clearly shown on the outside of the shipping container. C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the proper packing materials. UPS is usually the best way to ship the units. Heavy units should be “double-boxed” for safe transport. D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or damage to equipment that you ship. Of course, we insure the equipment when we ship it back to you. Lectrosonics USA: Mailing address: Lectrosonics, Inc. PO Box 15900 Rio Rancho, NM 87174 USA Shipping address: Lectrosonics, Inc. 581 Laser Rd. Rio Rancho, NM 87124 USA Web: www.lectrosonics.com E-mail: sales@lectrosonics.com Telephone: (505) 892-4501 (800) 821-1121 Toll-free (505) 892-6243 Fax Lectrosonics Canada: Mailing Address: 720 Spadina Avenue, Suite 600 Toronto, Ontario M5S 2T9 Telephone: (416) 596-2202 (877) 753-2876 Toll-free (877-7LECTRO) (416) 596-6648 Fax E-mail: Sales: colinb@lectrosonics.com Service: joeb@lectrosonics.com LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot correct the defect in your equipment, it will be replaced at no charge with a similar new item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you. This warranty applies only to items returned to Lectrosonics, Inc. or an authorized dealer, shipping costs prepaid, within one year from the date of purchase. This Limited Warranty is governed by the laws of the State of New Mexico. It states the entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT. This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state. 581 Laser Road NE • Rio Rancho, NM 87124 USA • www.lectrosonics.com +1(505) 892-4501 • fax +1(505) 892-6243 • (800) 821-1121 US and Canada • sales@lectrosonics.com 2 November 2015
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Create Date : 2015:11:02 09:24:49-07:00 Creator : Adobe InDesign CC 2015 (Windows) Modify Date : 2016:03:23 18:00:01-07:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Instance ID : uuid:91226b59-cd54-46de-a036-d7bbe3a0996f Original Document ID : adobe:docid:indd:13ff4b1a-7390-11dd-8002-d2eeb9106ad6 Document ID : xmp.id:25e86a5a-2862-564a-b3f6-792aaebbba01 Rendition Class : proof:pdf Version ID : 1 Derived From Instance ID : xmp.iid:434e4c02-d72e-9349-8dfd-4db226141c19 Derived From Document ID : xmp.did:f11286b5-ebd6-fa40-a5d9-7e057e1852b4 Derived From Original Document ID: adobe:docid:indd:13ff4b1a-7390-11dd-8002-d2eeb9106ad6 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2015 (Windows) History Changed : / History When : 2015:11:02 09:24:49-07:00 Metadata Date : 2016:03:23 18:00:01-07:00 Creator Tool : Adobe InDesign CC 2015 (Windows) Format : application/pdf Title : hma_man.indd Producer : Adobe PDF Library 15.0 Trapped : False GTS PDFX Version : PDF/X-4 Page Count : 20EXIF Metadata provided by EXIF.tools