Lectrosonics LMAE WIRELESS MICROPHONE TRANSMITTER User Manual USERS MANUAL

Lectrosonics Inc WIRELESS MICROPHONE TRANSMITTER USERS MANUAL

USERS MANUAL

LMaFrequency-Agile UHF Belt-Pack TransmitterFeaturingDigital Hybrid Wireless™ TechnologyUS Patent 7,225,135INSTRUCTION MANUALRio Rancho, NM, USAwww.lectrosonics.comFill in for your records: Serial Number: Purchase Date:
LMaLECTROSONICS, INC.2
Frequency-Agile UHF Belt-Pack TransmitterRio Rancho, NM 3Table of ContentsIntroduction .............................................................................................................................................................................................4Digital Hybrid Technology .....................................................................................................................................................................4Frequency Agility...................................................................................................................................................................................4Wide-Band Deviation ............................................................................................................................................................................4Long Battery Life ...................................................................................................................................................................................4Servo Bias Input and Wiring .................................................................................................................................................................4Input Limiter ..........................................................................................................................................................................................5No Pre-Emphasis/De-Emphasis ...........................................................................................................................................................5Pilot Tone Squelch ................................................................................................................................................................................5LMa Block Diagram ...............................................................................................................................................................................5Controls and Functions .........................................................................................................................................................................6Input Jack ..............................................................................................................................................................................................6Power ON/OFF Switch ..........................................................................................................................................................................6Power LED ............................................................................................................................................................................................6Frequency Select Switches ...................................................................................................................................................................6Modulation LEDs ...................................................................................................................................................................................6Audio Level ...........................................................................................................................................................................................6Antenna .................................................................................................................................................................................................6Belt Clip .................................................................................................................................................................................................6Battery Installation .................................................................................................................................................................................7Operating Instructions ...........................................................................................................................................................................8Selecting the Compatibility Mode ..........................................................................................................................................................8Attaching a Microphone or Musical Instrument and Adjusting Audio Levels .........................................................................................8Adjusting the Transmitter Frequency .....................................................................................................................................................95-Pin Input Jack Wiring ........................................................................................................................................................................10Microphone RF Bypassing ..................................................................................................................................................................10Line Level Signals ...............................................................................................................................................................................10Microphone Cable Terminationfor Non-Lectrosonics Microphones ................................................................................................11Wiring Hookups for Different Sources ...............................................................................................................................................12Compatible Wiring for Both Servo Bias Inputs and Earlier Transmitters: ............................................................................................12Simple Wiring for Servo Bias Inputs Only: ..........................................................................................................................................12Wiring Diagram for MI33A Instrument Cable ......................................................................................................................................13Troubleshooting ....................................................................................................................................................................................15Specifications and Features ................................................................................................................................................................16Service and Repair ...............................................................................................................................................................................17Returning Units for Repair ..................................................................................................................................................................17
LMaLECTROSONICS, INC.4IntroductionThe design of the LMa transmitter introduces the advanced technology and features of Digital Hybrid WirelessTM in a Lectrosonics belt-pack transmitter at a modest cost. Digital Hybrid Wireless™ combines a 24-bit digital audio chain with an analog FM radio link to eliminate a compandor and its artifacts, yet preserve the extended operating range and noise rejection of the finest analog wireless systems. DSP “compatibil-ity modes” allow the LMa to be used with a variety of analog receivers in addition to its native hybrid mode by emulating the compandors found in Lectrosonics 100 Series, 200 Series and IFB transmitters, and certain receivers from other manufacturers (contact the factory for details). Changing the compatibility mode is accom-plished with a simple procedure using the frequency switches and power switch.The housing is a rugged, machined aluminum package with removable, stainless steel wire belt clip. The input jack is a standard Lectrosonics 5-pin type for use with electret lavaliere mics, dynamic mics, musical instru-ment pickups and line level signals. The LEDs on the front panel allow quick and accurate level settings with-out having to view the receiver. The battery compart-ment accepts any 9 volt battery and makes a positive connection via self-adjusting contacts. The antenna is a super-rugged, permanently attached 1/4 wavelength design made of flexible galvanized steel cable.The switching power supplies in the LMa provide constant voltages to the transmitter circuits from the beginning (9.3 VDC) to the end (5.5 VDC) of battery life, with output power remaining constant over the life of the battery. The input amplifier uses an ultra low noise op amp for quiet operation. Input gain is adjustable over a 43 dB range, with a DSP controlled dual envelope input limiter to cleanly handle signal peaks over 30 dB above full modulation.Digital Hybrid Technology All wireless links suffer from channel noise to some degree, and all wireless microphone systems seek to minimize the impact of that noise on the desired signal. Conventional analog systems use compandors for enhanced dynamic range, at the cost of subtle artifacts (known as “pumping” and “breathing”). Wholly digital systems defeat the noise by sending the audio informa-tion in digital form, at the cost of some combination of power, bandwidth, operating range and resistance to interference.The Lectrosonics Digital Hybrid Wireless™ system overcomes channel noise in a dramatically new way, digitally encoding the audio in the transmitter and decoding it in the receiver, yet still sending the encoded information via an analog FM wireless link. This pro-prietary algorithm is not a digital implementation of an analog compandor but a technique which can be ac-complished only in the digital domain.Since the RF link between transmitter and receiver is FM, channel noise will increase gradually with increased operating range and weak signal condi-tions, however, the hybrid system handles this situa-tion elegantly with rarely audible audio artifacts as the receiver approaches its squelch threshold. In contrast, a purely digital system tends to drop the audio suddenly during brief dropouts and weak signal conditions. The Digital Hybrid Wireless™ system simply encodes the signal to use a noisy channel as efficiently and robustly as possible, yielding audio performance that rivals that of purely digital systems, without the power, noise and bandwidth problems inherent in digital transmis-sion. Because it uses an analog FM link, Digital Hybrid Wireless™ enjoys all the benefits of conventional FM wireless systems, such as excellent range, efficient use of RF spectrum, and long battery life.Frequency AgilityThe transmitter section uses a synthesized, frequency selectable main oscillator. The frequency is extremely stable over a wide temperature range and over time.Two rotary switches, located on the side panel provide 256 frequencies in 100 kHz steps over a 25.6 MHz bandwidth.Wide-Band DeviationIn the Digital Hybrid and 200 Series modes, the sys-tem uses ±75 kHz deviation to dramatically improve the capture ratio, and signal to noise ratio of the overall wireless system.Long Battery LifeThe use of switching power supplies throughout the design allows over 6 hours of operation using a single 9 volt alkaline battery and over 7 hours of operation with a 9 volt LiPolymer rechargeable battery. The battery contacts are spring loaded to prevent “rattle” as the unit is handled.Servo Bias Input and WiringThe LMa input preamp is a radically different design than previous Lectrosonics transmitter inputs. The improve-ments are audible and make the transmitters easier to use and much harder to overload. It is no longer neces-sary on some mics to introduce pads to prevent over-load of the input stage, divide the bias voltage down for some low voltage mics, or reduce the limiter range at minimum gain settings.Two different microphone wiring schemes are now available to simplify and standardize the configuration. Simplified 2-wire and 3-wire configurations for the servo bias input only take full advantage of the preamp cir-cuitry to maximize the signal to noise ratio, and several other configurations are available that are compatible with the servo bias input and earlier types. The input will automatically switch the low frequency roll-off to 35 Hz when the MI33ARA and MI33AST
Frequency-Agile UHF Belt-Pack TransmitterRio Rancho, NM 5are eliminated.Pilot Tone SquelchThe DSP in the transmitter generates one of 256 differ-ent ultrasonic tones between 25 and 32 kHz to operate the receiver squelch (audio muting). The benefit of a pilot tone squelch system is that the receiver will remain quiet until it receives the pilot tone from the matching transmitter, even if a strong RF signal is present on the carrier frequency of the system. The pilot tone also eliminates noise (pops, thumps, etc.) from occurring when the transmitter is powered on and off.The pilot tone frequency is chosen according to which of the 256 channels has been selected by the frequen-cy switch setting. This ensures that all transmitters in a system have different pilot tone frequencies so even spurious RF from the wrong transmitters can’t open the receiver squelch.instrument cables are connected.Input LimiterThe transmitter employs a digitally-controlled analog audio limiter prior to the analog-to-digital converter. The limiter has a range greater than 30 dB for excellent overload protection. A dual release envelope makes the limiter acoustically transparent while maintaining low distortion. It can be thought of as two limiters in series, connected as a fast attack and release limiter followed by a slow attack and release limiter. The limiter recovers quickly from brief transients, so that its action is hidden from the listener, but recovers slowly from sustained high levels to keep audio distortion low and preserve short term dynamic changes in the audio.No Pre-Emphasis/De-EmphasisBecause the signal to noise ratio of the hybrid system is so high, there is no need for conventional pre-emphasis (HF boost) in the transmitter and de-emphasis (HF roll off) in the receiver. Thus, the possible distortion prob-lems associated with pre-emphasis and de-emphasis FreqSwitchesBicolorModulationLEDs 9VBatteryBicolorPowerLED+5vLMa Block Diagram
LMaLECTROSONICS, INC.6Controls and FunctionsInput JackThe 5-pin (Switchcraft TA5F compatible) input accom-modates virtually every lavaliere, hand-held or shotgun microphone available, and most musical instrument signals. Line level signals can also be accommodated. (See 5-Pin Input Jack Wiring.)Power ON/OFF SwitchThe Power ON/OFF switch turns the transmitter on and off. The pilot tone muting system prevents transient noise (pops, thumps, etc.) from occurring at the receiver even if the transmitter is abruptly switched on or off.Power LEDThe Power LED glows green when the transmitter is operating and the battery is good. It turns red when the battery voltage drops to 6.1 VDC and starts blinking red when the voltage drops to 5.6 VDC. When using a recommended lithium or alkaline battery, there will be about 30 minutes of operating time remaining when the Power LED first begins blinking red.Note: A weak battery will sometimes cause the Power LED to glow green, but it will soon discharge to the point where it will turn red or go out completely. If in doubt, replace the battery with a known new battery. If the Power LED fails to glow when the transmitter is turned on, replace the battery.LiPolymer rechargeable batteries give little or no warn-ing when they are depleted. If you wish to use these batteries in the transmitter, you will need to manually keep track of the operating time to prevent interruptions caused by dead batteries. Start with a fully charged bat-tery, then measure the time it takes for the Power LED to go out completely. Note: A number of Lectrosonics receivers incorporate a Battery Timer function which tracks the amount of time the transmitter signal is detected. See your receiver manual to determine if this function is available and, if so, the instructions on measuring the actual run time of the battery.Frequency Select SwitchesTwo 16-position rotary Frequency Select Switches, ac-cessed through the left side panel, are used to adjust the transmitter’s operating frequency. These switches are labeled 1.6M and 100K. The 1.6M switch is used for coarse frequency adjustments and the 100K is used for fine frequency adjustment.Modulation LEDsThe Modulation LEDs provide a visual indication of the input audio signal level from the microphone or musical instrument. These two bicolor LEDs can glow either red or green to indicate modulation levels. The Modulation LEDs are also used to indicate the Compatibility Mode when the transmitter is initially turned on. The Modulation LEDs will blink simultane-ously: • Oncefor100Seriesmode •Twotimesfor200Seriesmode •Threetimesformode3 •FourtimesforDigitalHybridWireless™ or 400 Series mode •FivetimesforIFBmode •Sixtimesformode6Audio LevelThe AUDIO LEVEL control is used to set the input gain for the proper modulation.AntennaThe flexible, insulated galvanized steel cable antenna supplied with the transmitter is cut to 1/4 wavelength of the center of the frequency block (the frequency range) of the transmitter. Belt ClipThe belt clip may be removed for special applications by pulling the ends out of the holes in the sides of the case. An optional hinged belt clip (P/N BCHINGED) is also available. Contact a Lectrosonics sales represen-tative, or visit our web site (www.lectrosonics.com) for more details.AUDIO LEVEL controlPower LEDAntennaInput JackModulation LEDsPowerON/OFFBelt Clip Attachment HolesFrequency Select SwitchesBattery Compartment Door
Frequency-Agile UHF Belt-Pack TransmitterRio Rancho, NM 7Battery InstallationThe transmitter is powered by a standard 9 volt battery. We recommend using alkaline, lithium, or rechargeable LiPolymer batteries for longest life. Standard zinc-car-bon batteries marked “heavy-duty” or “long-lasting” are not adequate. Alkaline batteries provide over six hours of operation at room temperature. LiPolymer bat-teries will last about 7 hours per charge, and Lithium batteries can provide up to 13 hours. The battery status circuitry is designed for the voltage drop over the life of alkaline batteries. Because rechargeable LiPolymer bat-teries run down quite abruptly, using the Power LED to verify battery status is not reliable with LiPolymer batter-ies. However, it may be possible to track battery status using the Battery Timer function available in a number of Lectrosonics receivers. (Refer to the associated receiver manual to determine if this function is available in your situation.) Warning: Care should be taken not to leave a fully discharged lithium battery in the transmitter, as swelling of the battery can make it difficult to remove from the compartment.To replace the battery, push up on the Battery Com-partment Door and rotate it clockwise. (See photo.) Remove the old battery and take note of the polarity marked inside showing the location of the positive (+) and negative ( -) terminals. (You can see the large and small contact holes inside the battery compartment with the door open.)Insert the new battery correctly and rotate the door to snap flush against the housing. If the battery is inserted incorrectly, the door will not fully close. Do not force the door closed.
LMaLECTROSONICS, INC.80123456789ABCDEF0123456789ABCDEFAttaching a Microphone or Musical Instrument and Adjusting Audio LevelsThe front panel Modulation LEDs indicate input level and limiter activity. (See Modulation LED Signal Level Table.) Since the distortion introduced by the limiter is minimal and full modulation is assured, occasional red flickering of the -20 LED is desirable.Different voices or instruments will usually require dif-ferent settings of the AUDIO LEVEL control, so check this adjustment as each new person uses the system. If several different people will be using the transmitter and there is not time to make the adjustment for each individual, adjust it for the loudest voice.Musicians also vary their volume depending on the na-ture of the music. It is suggested that the transmitter be adjusted for the passage with the loudest volume.1) If necessary, install a fresh battery.2) Insert the 5-pin into the input jack. Ensure the pins are aligned and the connector locks in (it will click). For those using a musical instrument, insert the 1/4 inch plug on the other end of the instrument cable into the appropriate jack on your musical instru-ment.3) Mute the main sound system or amplifier and rotate the AUDIO LEVEL control on the transmitter to maximum counterclockwise (Off).4) Set the transmitter Power switch to ON.5) For microphone users, position the microphone in the location where it will be used in actual opera-tion. For musicians, adjust the instrument volume con-trols to the highest levels that would be used during a performance.Selecting the Compatibility ModeThe LMa transmitter is capable of working with Lec-trosonics 400 Series Digital Hybrid Wireless™, 200 Series analog, 100 Series analog and some non-Lec-trosonics analog wireless receivers (contact the factory for details). The transmitter must be set to the operating mode of the matching receiver, which is easily done us-ing the supplied screwdriver and a battery.NOTE: The unit is supplied from the factory as a 400 series transmitter.1) Ensure the battery is good.2) Turn OFF the transmitter.3) With a small screwdriver (one is included with your unit), set the Frequency Select Switches to CC. (for Change, Change). 4) Toggle the power switch ON briefly – just long enough for the LED’s to light up and then turn it OFF.5) Change the Frequency Select Switches to one of the following settings: •100Seriesmode: 1,1 •200Seriesmode: 2,2 •Mode3:  3,3 •400Seriesmode: 4,4 •IFBSeriesmode: 5,5 •Mode6:  6,66) Toggle the power switch ON, then OFF again.7) Change the Frequency Select Switches to 0,0.8) Turn the transmitter ON to complete the operation.The LEDS will blink to indicate the selected com-patibility mode. Immediately after power up, all LEDs will blink together red, then green, followed by the audio level LEDs (-20 and -10) blinking to indicate the mode. The LEDs will blink: •Oncefor100Seriesmode  •Twotimesfor200Seriesmode  •Threetimesforsomeotherreceivers  •Fourtimesfor400Seriesmode  •FivetimesforIFBmode  •SixtimesforMode6Note: Each time the transmitter is turned on, the Modulation LEDs will confirm the current operating mode with the number of blinks listed in Step 2. The mode setting will not change until it is reset with the procedure listed above. Attention: During the procedure to set the compatibility mode, each step between toggles of the power switch must be performed within ten seconds, or the procedure must be started from the beginning.Operating InstructionsFrequency Select Switch Settings (C,C) 1.6M 100K
Frequency-Agile UHF Belt-Pack TransmitterRio Rancho, NM 9Adjusting the Transmitter FrequencyThe left switch adjusts the operating frequency of the transmitter up or down in 1.6 MHz steps. The right switch adjusts the operating frequency of the transmit-ter up or down in 100 kHz steps. It is suggested to use the metering on the associated receiver to find a clear channel. Turn the transmitter off and leave the receiver turned on.All 400 Series (and a number of earlier receivers) offer front panel LCDs that indicate the correct transmitter switch settings, and built in scanning functions to help locate clear channels. Use the scanning functions on these receivers to find a clear channel, then switch the transmitter to the frequency settings indicated in the receiver’s display.The R400A, Venue Series and other Lectrosonics receivers have an automatic scanning function called SmartTuneTM that automatically locates clear operat-ing channels. If your receiver does not have a built in scanning function, manually tune the receiver across its band and find a frequency where little or no RF activity is indicated.After finding a clear channel, set the transmitter to this new frequency, then turn it on and make sure the RF signal is strongly indicated at the receiver. Be sure the switch settings between the receiver and transmitter are set exactly the same. If, for example, the 100K switch is one click above or below the desired frequency, the receiver will indicate RF, but no audio (or severely dis-torted audio) will be produced.Input JackAUDIO LEVELControl-20 LED-10 LED6) For microphone users, observe the Modulation LEDs while speaking or singing at the same voice level that will be used during the program. Gradu-ally rotate the AUDIO LEVEL control clockwise until the -10 LED glows green and the -20 dB glows green with occasional red flickers. This indicates full modulation and is the optimum setting for the transmitter’s gain. For musicians, gradually rotate the AUDIO LEVEL control clockwise while playing the loudest notes that will be played during the performance. It is ideal for the -20 LED to briefly flicker red during the loud-est passages.7) Once the transmitter’s audio gain has been set, the remaining components of the audio system can be energized and adjusted.Warning: DO NOT use the audio level control for controlling the volume of your sound system or recorder levels. This gain adjustment matches the transmitter gain with the user’s voice level and microphone positioning, or the instrument output level.0123456789ABCDEF0123456789ABCDEFFrequency Select Switch Settings 1.6M 100KModulation LED Signal Level TableSignal Level -20 LED -10 LEDLess than -20 dB Off Off-20 dB to -10 dB Green Off-10 dB to +0 dB Green Green+0 dB to +10 dB Red GreenGreater than +10 db Red Red
LMaLECTROSONICS, INC.10The wiring diagrams included in this section represent the basic wiring necessary for the most common types of microphones and other audio inputs. Some micro-phones may require extra jumpers or a slight variation on the diagrams shown.It is virtually impossible to keep completely up to date on changes that other manufacturers make to their products, thus you may encounter a microphone that differs from these instructions. If this occurs please call our toll-free number listed under Service and Repair in this manual or visit our web site at: www.lectrosonics.com10k1k54321To Virtual GroundAudio AmplifierBIASMICBIAS SELECTLINE INGND+30uF+5 VDCServo BiasPin 4 to Pin 1 = 0 V Pin 4 Open = 2 VPin 4 to Pin 2 = 4 V+To Limiter Control30uF500 Ohm100 Ohm2.7K200 Ohm+3.3uF100 OhmAudio input jack wiring:PIN 1 Shield (ground) for positive biased electret lava-liere microphones. Shield (ground) for dynamic microphones and line level inputs.PIN 2 Bias voltage source for positive biased electret lavaliere microphones.PIN 3 Low impedance microphone level input for dynamic microphones. Also accepts hand-held electret microphones provided the microphone has its own built-in battery.PIN 4 Bias voltage selector for Pin 3. Pin 3 voltage (0, 2 or 4 volts) depends on Pin 4 connection.Pin 4 tied to Pin 1: 0 VPin 4 Open: 2 VPin 4 to Pin 2: 4 VPIN 5 High impedance, line level input for tape decks, mixer outputs, musical instruments, etc.Microphone RF BypassingWhen used on a wireless transmitter, the microphone element is in the proximity of the RF coming from the transmitter. The nature of electret microphones makes them sensitive to RF, which can cause problems with the microphone/transmitter compatibility. If the electret microphone is not designed properly for use with wire-less transmitters, it may be necessary to install a chip capacitor in the mic capsule or connector to block the RF from entering the electret capsule.5-Pin Input Jack WiringSome mics require RF protection to keep the radio signal from affecting the capsule, even though the transmitter input circuitry is already RF bypassed (see schematic diagram).If the mic is wired as directed, and you are having dif-ficulty with squealing, high noise, or poor frequency response, RF is likely to be the cause.The best RF protection is accomplished by installing RF bypass capacitors at the mic capsule. If this is not pos-sible, or if you are still having problems, capacitors can be installed on the mic pins inside the TA5F connector housing.3 WIRE MIC2 WIRE MICCAPSULE CAPSULESHIELDAUDIOSHIELDAUDIOBIASAlternate locations for bypass capacitorsTA5FCONNECTORTA 5FCONNECTORPreferred locations for bypass capacitorsInstall the capacitors as follows: Use 330 pF capaci-tors. Capacitors are available from Lectrosonics. Please specify the part number for the desired lead style. Leaded capacitors: P/N 15117 Leadless capacitors: P/N SCC330PAll Lectrosonics lavaliere mics are already bypassed and do not need any additional capacitors installed for proper operation.Line Level SignalsThe normal hookup for line level signals is: Signal Hot to pin 5, Signal Gnd to pin 1 and pin 4 jumped to pin 1. This allows signal levels up to 3V RMS to be applied without limiting.If more headroom is needed, insert a 20 k resistor in series with pin 5. Put this resistor inside the TA5F con-nector to minimize noise pickup.
Frequency-Agile UHF Belt-Pack TransmitterRio Rancho, NM 11NOTE: This termination is intended for UHF transmitters only. VHF transmitters with 5-pin jacks require a different termination. Lectrosonics lavaliere microphones are terminated for compatibility with VHF and UHF transmitters, which is different than what is shown here.Microphone Cable Termination for Non-Lectrosonics MicrophonesTA5F Connector AssemblyMic Cord Stripping Instructions12345VIEW FROM SOLDERSIDE OF PINS0.3"0.15"Crimping to Shield and InsulationShieldInsulationStrip and position the cable so that the clamp can be crimped to contact both the mic cable shield and the insulation. The shield contact reduces noise with some microphones and the insulation clamp increases ruggedness.Crimp these fingers to contact the shieldCrimp these fingers to clamp the insulation
LMaLECTROSONICS, INC.122 VOLT POSITIVE BIAS 2-WIRE ELECTRETSimplified wiring for microphones such as Countryman B6 Lavalier and E6 Earset models and others.NOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring.Compatible Wiring for Both Servo Bias Inputs and Earlier Transmitters:Simple Wiring for Servo Bias Inputs Only:4 VOLT POSITIVE BIAS 3-WIRE ELECTRETNOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring.Wiring Hookups for Different SourcesIn addition to the microphone and line level wiring hook-ups illustrated below, Lectrosonics makes a number of cables and adapters for other situations such as con-necting musical instruments (guitars, bass guitars, etc.) to the transmitter. Visit www.lectrosonics.com and click on Accessories, or download the master catalog.1 2 3 4 5 PIN SHIELD A UDI O 1 2 3 4 5 T A5 F PLUG 3.3 k1.5 k 2 VOLT POSITIVE BIAS 2-WIRE ELECTRET Compatible wiring for microphones such as Countryman E6 headworn and B6 lavaliere.4 VOLT POSITIVE BIAS 2-WIRE ELECTRETMost common type of wiring for lavaliere mics. Fully compatible with 5-pin inputs on Lectrosonics transmitters such as the LM and UM Series.DRAIN (BIAS)SOURCE (AUDIO)SHIELD4 VOLT POSITIVE BIAS 3-WIRE ELECTRET WITH EXTERNAL RESISTORThis wiring is fully compatible with 5-pin inputs on Lectrosonics transmitters such as the LM and UM Series. This is the wiring for the Lectrosonics M152 lavaliere microphone.Used for 3-wire lavaliere microphones that require an external resistor such as the Sanken COS-11.SHIELD TIP PIN 5 4 3 2 1 SLEEVE LINE LEVEL RCA or 1/4” PLUG A UDI O 1 2 3 4 5 T A5 F PLUG UNBALANCED LINE LEVEL SIGNALSFor signal levels up to 3V (+12 dBu) before limiting. Fully compatible with 5-pin inputs on other Lectrosonics transmitters such as the LM and UM Series. A 20k ohm resistor can be inserted in series with Pin 5 for an additional 20 dB of attenuation to handle up to 30V (+32 dBu).BALANCED AND FLOATING LINE LEVEL SIGNALS*NOTE: If the output is balanced but center tapped to ground, such as on all Lectrosonics receivers, do not connect Pin 3 of the XLR jack to Pin 4 of the TA 5F connector.TA5F PLUGXLR JACKLO-Z MICROPHONE LEVEL SIGNALSFor low impedance dynamic mics or electret mics with internal battery or power supply.XLR JACKA lot of information regarding microphone wiring is also available in the FAQ section of the web site at:http://www.lectrosonics.com/faq.htmFollow the instructions to search by model number or other search options.2 VOLT POSITIVE BIAS 2-WIRE ELECTRET - DPA MICROPHONESThis wiring is for DPA lavalier and headset microphones.NOTE: The resistor value can range from 3k to 4k ohms.2 VOLT NEGATIVE BIAS 2-WIRE ELECTRETSimplified wiring for microphones such as negative bias TRAM.NOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring.12345PINSHIELDAUDIO1 2 3 4 5 T A5 F PLUG 2.7 k2 VOLT NEGATIVE BIAS 2-WIRE ELECTRETCompatible wiring for microphones such as negative bias TRAM models.NOTE: The resistor value can range from 2k to 4k ohms.
Frequency-Agile UHF Belt-Pack TransmitterRio Rancho, NM 13Wiring Diagram for MI33A Instrument CableThe MI33ARA and MI33AST instrument cable assem-blies allow an optimum match between musical instru-ment pickups and Lectrosonics transmitters with 5-pin input connectors. The low frequency roll-off in the LMa will be set to 35 Hz automatically when these cables are connected.The active preamp and low noise wire cable provide a “same as wire” experience in a wireless environment.The 30 inch long cable offers enough cable to com-fortably link the instrument to the wireless transmitter without being excessive.Note: This cable is prewired and cannot be field modified. The cable is available in two configurations, MI33ARA (right angle) and MI33AST (straight).SHIELDTIPPIN54321SLEEVE1/4 " PLUG12345PreampAUDIOTA 5FPLUGSHIELDAUDIOPWR3 k
LMaLECTROSONICS, INC.14TroubleshootingIt is important that you follow these steps in the sequence listed.Symptom: Possible Cause:Transmitter Battery LED off 1. Battery is inserted backwards.when Power Switch “ON” 2. Battery is dead.No Transmitter Modulation LEDs 1. Gain control turned all the way down.when Signal Should be Present 2. Battery is in backwards. Check power LED. 3. Mic capsule is damaged or malfunctioning. 4. Mic cable damaged or miswired. 5. Instrument Cable damaged or not plugged in. 6. Musical instrument output level set too low.Receiver Indicates RF But No Audio 1. Audio source or cable connected to transmitter is defective. Try using an alternate source or cable. 2. Make sure the compatibility mode is the same on transmitter and receiver. 3. Ensure musical instrument volume control is not set to minimum.Receiver RF Indicator Off 1. Ensure that the transmitter and receiver Frequency Select Switches are set to the same frequency. 2. Transmitter not turned on, or battery is dead. 3. Receiver antenna missing or improperly positioned. 4. Transmitter and receiver not on same frequency. Check switches/display on transmitter and receiver. 5. Operating distance is too great.No Sound (Or Low Sound Level), Receiver 1. Receiver output level set too low.Indicates Proper Audio Modulation 2. Receiver output is disconnected; cable is defective or miswired. 3. Sound system or recorder input is turned down.Distorted Sound 1. Transmitter gain (audio level) is too high. Check Modulation LEDs on transmitter and receiver while distortion is being heard. 2. Receiver output level may be mismatched with the sound system or recorder input. Adjust output level on receiver to the correct level for the recorder, mixer or sound system. 3. Transmitter and receiver may not be set to the same compatibility mode. Some mis-matched combinations will pass audio. 4. RF interference. Reset both transmitter and receiver to a clear channel.Wind Noise or Breath “Pops’” 1. Reposition microphone, or use a larger windscreen, or both. 2. Omni-directional mics produce less wind noise and breath pops than directional types.Hiss and Noise -- Audible Dropouts 1. Transmitter gain (audio level) far too low. 2. Receiver antenna missing or obstructed. 3. Operating distance too great. 4. RF interference. Reset both transmitter and receiver to a clear channel. 5. Musical instrument volume set too low.ExcessiveFeedback(WithMicrophone) 1. Transmitter gain (audio level) too high. Check gain adjustment and/or reduce receiver output level. 2. Microphone too close to speaker system. 3. Microphone is too far from user’s mouth.
Frequency-Agile UHF Belt-Pack TransmitterRio Rancho, NM 15The FCC requires that the following statement be included in this manual:This device complies with FCC radiation exposure limits as set forth for an uncontrolled environment. This device should be installed and operated so that its antenna(s) are not co-located or operating in conjunction with any other antenna or transmitter.Operating frequencies: Block 470 470.100 - 495.600 Block 19 486.400 - 511.900 Block 20 512.000 - 537.500 Block 21 537.600 - 563.100 Block 22 563.200 - 588.700 Block 23 588.800 - 607.900 and 614.100 - 614.300 Block 24 614.400 - 639.900 Block 25 640.000 - 665.500 Block 26 665.600 - 691.100 Block 27 691.200 - 716.700 Block 28 716.800 - 742.300 Block 29 742.400 - 767.900 (Frequency usage varies by countryFrequency Selection: 256 frequencies in 100 kHz stepsChannel Separation: 100 kHzCompatibility Modes: Lectrosonics 400 Series (Digital Hybrid), 200 Series, 100 Series, and IFB. Mode 3, Mode 6 (Other brands).RF Power output: Greater than 50 mWPilot tone: 25 to 32 kHz frequency; 5 kHz deviation (400 Series only)Frequency stability: ± 0.002%Deviation: ± 75 kHz max. (200 & 400 Series Modes)Spurious radiation: 60 dB below carrierEquivalent input noise: –120 dBV, A-weightedInput level: If set for dynamic mic: 0.5 mV to 50 mV before limiting. Greater than 1 V with limiting. If set for electret lavaliere mic: 1.7 uA to 170 uA before limiting. Greater than 5000 uA (5 mA) with limiting. Line level input: 5.0 mV to 6 V before limiting. Greater than 15 V with limiting.Input impedance: Dynamic mic: 300 Ohms Electret lavaliere: Input is virtual ground with servo adjusted constant current bias Line level: 2.7 k OhmsInput limiter: Dual envelope, >30 dB range (Note: The dual envelope “soft” limiter provides exceptionally good handling of transients using variable attack and release time constraints.)Gain control range: 43 dB; semi-log rotary controlModulation indicators: Dual bicolor LEDs indicate modulation of -20, -10, 0, +10 dB referenced to full modulation.Low frequency roll-off: Microphone: –12 dB/octave; -3 dB @ 70 Hz Instrument Cable: –12 dB/octave; -3 dB @ 35 HzAudio frequency response (overall system): Microphone : 90 Hz to 20 kHz (+/- 1 dB) with the 70Hz low frequency roll-off filter. Instrument Cable : 40 Hz to 20 kHz (+/- 1 dB)Controls: 2 position “OFF-ON” slide switch for noiseless turn on/turn off operation. Front panel audio gain control. Rotary switches on side panel adjust transmitter frequency.Audio Input Jack: Switchcraft 5 pin locking (TA5F)Antenna: Galvanized steel, flexible wire.Battery: Precision compartment auto-adjusts to accept any known alkaline 9 volt battery. Battery Life: 6 hours (alkaline); 7 hours (LiPolymer); 13 hours continuous (lithium)Weight: 6.3 ozs. including batteryDimensions: 3.1 x 2.4 x .75 inchesEmission Designator: 180KF3ESpecifications and FeaturesSpecifications subject to change without notice
LMaLECTROSONICS, INC.16Service and RepairIf your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the Troubleshooting section in this manual.We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop at-tempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connection, send the unit to the factory for repair and service. Don’t attempt to adjust any controls inside the units. Once set at the factory, the various controls and trimmers do not drift with age or vibration and never require readjustment. There are no adjustments inside that will make a malfunctioning unit start working.LECTROSONICS’ Service Department is equipped and staffed to quickly repair your equipment. In warranty repairs are made at no charge in accordance with the terms of the warranty. Out-of-warranty repairs are charged at a modest flat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone for out-of-warranty repairs.Returning Units for RepairFor timely service, please follow the steps below:A. DO NOT return equipment to the factory for repair without first contacting us by email or by phone. We need to know the nature of the problem, the model number and the serial number of the equipment. We also need a phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time).B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed your repair through our receiving and repair departments. The return authorization number must be clearly shown on the outside of the shipping container.C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the proper packing materials. UPS is usually the best way to ship the units. Heavy units should be “double-boxed” for safe transport.D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or dam-age to equipment that you ship. Of course, we insure the equipment when we ship it back to you.Lectrosonics USA:Mailing address: Shipping address: Telephone: Lectrosonics, Inc. Lectrosonics, Inc. (505) 892-4501 PO Box 15900 581 Laser Rd. (800) 821-1121 Toll-free Rio Rancho, NM 87174 Rio Rancho, NM 87124 (505) 892-6243 Fax USA USA Web: E-mail: www.lectrosonics.com sales@lectrosonics.comLectrosonics Canada:Mailing Address: Telephone: E-mail: 49 Spadina Avenue, (416) 596-2202 Sales: colinb@lectrosonics.com Suite 303A (877) 753-2876 Toll-free Service: joeb@lectrosonics.com Toronto, Ontario M5V 2J1 (877-7LECTRO) (416) 596-6648 Fax
Frequency-Agile UHF Belt-Pack TransmitterRio Rancho, NM 17
LMaLECTROSONICS, INC.18
Frequency-Agile UHF Belt-Pack TransmitterRio Rancho, NM 19
LMa581 Laser Road NE • Rio Rancho, NM 87124 USA • www.lectrosonics.com(505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.com6 Mar 2008LIMITED ONE YEAR WARRANTYThe equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment.Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot correct the defect in your equipment, it will be replaced at no charge with a similar new item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you.This warranty applies only to items returned to Lectrosonics, Inc. or an authorized dealer, shipping costs prepaid, within one year from the date of purchase.This Limited Warranty is governed by the laws of the State of New Mexico. It states the entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT.This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state.

Navigation menu