Lectrosonics SMV9 Wireless Microphone Transmitter User Manual SMV 941 Series man indd

Lectrosonics Inc Wireless Microphone Transmitter SMV 941 Series man indd

User Manual

SMV-941 SeriesSuper Miniature Variable Power TransmittersWith Digital Hybrid Wireless® TechnologySMV-941 Single Battery ModelSMQV-941 Dual Battery ModelINSTRUCTION MANUALRio Rancho, NM, USAwww.lectrosonics.comFill in for your records: Serial Number: Purchase Date:US Patent 7,225,135Digital Hybrid Wireless®US Patent 7.225.135
SMV SeriesLECTROSONICS, INC.2IntroductionThe SM Series variable power transmitters are the product of many years of engineering and experience in professional audio markets. The unique design provides several distinct features for professional applications:• Selectable output power to maximize battery life or operating range as needed• Superb, compandor-free audio quality• Ultra-lightweight, corrosion resistant housing• Water resistant seals for use in damp environments• Programmable compatibility modes for use with a wide variety of different receiversThe Digital Hybrid Wireless® design (US Patent 7,225,135) combines 24-bit digital audio with analog FM resulting in a system that has the same operating range as analog systems, the same spectral efficiency as analog systems, the same long battery life as analog systems, plus the excellent audio fidelity typical of pure digital systems.The SM Series transmitters feature the unique servo bias input circuitry with a standard TA5M type input jack for use with electret lavaliere mics, dynamic mics, or line level signals. A water resistant control panel with LCD, membrane switches and multi-color LEDs make input gain adjustments, frequency and compatibility mode selection quick and accurate, without having to view the receiver. The battery compartment accepts AA lithium or rechargeable batteries. The housings are machined from solid aluminum billets to provide an extremely lightweight and rugged package. A special non-corrosive finish resists salt water exposure and perspiration in extreme environments.
Super-Minature Belt Pack TransmitterRio Rancho, NM 3Table of ContentsIntroduction ............................................................................ 2General Technical Description ............................................. 4Controls and Functions ........................................................ 6LCD Screen ......................................................................... 6Power LED ........................................................................... 6Power LED Off Feature ........................................................ 6Audio Input Jack ................................................................... 6AUDIO and FREQ Buttons ................................................... 6UP/DOWN Arrow Buttons .................................................... 6Battery and Battery Eliminator Installation ......................... 7Attaching and Removing the Microphone ........................... 7Operating Instructions .......................................................... 8Power Up and Boot Sequence ............................................. 8Power Down ......................................................................... 8Standby Mode ...................................................................... 8Menus .................................................................................. 8Locking/Unlocking the Control Panel ................................. 10Remote Control Operation ................................................. 105-Pin Input Jack Wiring ....................................................... 11Installing the Connector: .................................................... 11Line Level Signals .............................................................. 11Microphone Cable Termination for Non-Lectrosonics Microphones ............................ 12Microphone RF Bypassing ................................................. 13Wiring Hookups for Different Sources .............................. 14Silver Paste on SM Series Transmitter Thumbscrews ...... 15LectroRM .............................................................................. 16Accessories for single battery models: ............................. 17Accessories for dual battery models: ................................ 17Accessories for Both Models ............................................. 18Specifications and Features ............................................... 19Specifications ..................................................................... 19Troubleshooting ................................................................... 20Service and Repair .............................................................. 22Returning Units for Repair ................................................. 22For body worn operation, this transmitter models has been tested and meets the FCC RF exposure guidelines when used with the Lectrosonics accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Contact Lectrosonics if you have any questions or need more information about RF exposure using this product..This device complies with FCC radiation exposure limits as set forth for an uncontrolled environment. This device should be installed and operated so that its antenna(s) are not co-located or operating in conjunction with any other antenna or transmitter.
SMV SeriesLECTROSONICS, INC.4Variable 1.8 - 4v+6V+5V 5VRegulatorServo Bias InputThe voltage and current requirements of the wide vari-ety of electret microphones used in professional appli-cations has caused confusion and compromises in the wiring needed for wireless transmitters. To address this problem, the unique Servo Bias input circuit provides an automatically regulated voltage over a very wide range of current for compatibility with all microphones.Digital Hybrid Wireless® TechnologyAll wireless links suffer from channel noise to some de-gree, and all wireless microphone systems seek to mini-mize the impact of that noise on the desired signal. Con-ventional analog systems use compandors for enhanced dynamic range, at the cost of subtle artifacts (typically “pumping” and “breathing”). Wholly digital systems defeat the noise by sending the audio information in digital form, at the cost of some combination of power, bandwidth and resistance to interference.Digital Hybrid systems overcome channel noise in a dramatically new way, digitally encoding the audio in the transmitter and decoding it in the receiver, yet still send-ing the encoded information via an analog FM wireless link. This proprietary algorithm is not a digital imple-mentation of an analog compandor but a technique that can be accomplished only in the digital domain, even though the inputs and outputs are analog.Because it uses an analog FM link, the Digital Hybrid system enjoys all the benefits of conventional FM wire-less systems and it does away with the analog compan-dor and its artifacts.General Technical DescriptionNo Pre-Emphasis/De-EmphasisThe Digital Hybrid design results in a signal-to-noise ratio high enough to preclude the need for conventional pre-emphasis (HF boost) in the transmitter and de-emphasis (HF roll off) in the receiver. This eliminates the potential for distortion of signals with abundant high-frequency information.Low Frequency Roll-OffThe low frequency roll-off can be set for a 3 dB down point at 35, 50, 70, 100, 120 and 150 Hz to control sub-sonic and very low frequency audio content in the au-dio. The actual roll-off frequency will vary slightly depend-ing upon the low frequency response of the microphone.Excessive low frequency content can drive the transmit-ter into limiting, or in the case of high level sound sys-tems, can even cause damage to loudspeaker systems. The roll-off is normally adjusted by ear while listening as the system is operating.Input LimiterA DSP-controlled analog audio limiter is employed be-fore the A-D converter. The limiter has a range of more than 30 dB for excellent overload protection. A dual re-lease envelope makes the limiter acoustically transpar-ent while maintaining low distortion. It can be thought of as two limiters in series, a fast attack and release limiter followed by a slow attack and release limiter. The limiter recovers quickly from brief transients, with no audible side effects, and also recovers slowly from sustained high levels to keep audio distortion low while preserving short term dynamics.
Super-Minature Belt Pack TransmitterRio Rancho, NM 5Signal Encoding and Pilot ToneIn addition to controlling the limiter, the DSP also en-codes the digitized audio from the A/D converter and adds an ultrasonic pilot tone to control the squelch in the receiver. A pilot tone squelch system provides a reli-able method of keeping a receiver output muted (audio mute) even in the presence of significant interference. When the system is operating in the hybrid mode, a dif-ferent pilot tone frequency is generated for each carrier frequency to prevent inadvertent squelch problems in multi-channel sytems.Microprocessor ControlA microprocessor monitors user command inputs from the control panel buttons and numerous other internal signals. It works intimately with the DSP to ensure the audio is encoded according to the selected Compatibil-ity Mode and that the correct pilot tone is added to the encoded signal.Compatibility ModesSM transmitters are designed to operate with Lectroson-ics Digital Hybrid receivers and will yield the best per-formance when doing so, however, due to the flexibility of digital signal processing, the transmitter can also operate with Lectrosonics IFB receivers in the same frequency band.Control PanelThe control panel includes four membrane switches and an LCD screen to adjust the operational settings. Multi-color LEDs are used to indicate audio signal levels for accurate gain adjustment and for battery status.Variable Power OutputThis advanced feature allows the operator to optimize the transmitter for maximum battery life, or for slightly increased operating range. Power output is selected us-ing the LCD in a setup mode while the RF output of the transmitter is turned off.Battery Options and Operating TimeSwitching power supplies convert regulated battery volt-ages to operate various circuit stages with maximum efficiency. The firmware “remembers” the power status when a battery fails, so the transmitter will be turned on auto-matically when the battery is replaced and the previous settings will be enabled.Circulator/IsolatorThe RF output circuit includes a one way circulator/iso-lator using a magnetically polarized ferrite. This device greatly reduces RF intermodulation produced when multiple transmitters are used in close proximity to one another (several feet apart). The isolator also provides additional RF output stage protection against static shock.
SMV SeriesLECTROSONICS, INC.6Controls and FunctionsLCD ScreenThe LCD is a numeric-type Liquid Crystal Display with screens for adjusting power, frequency, audio level and low frequency audio roll-off. The transmitter can be powered up with or without the RF output turned on. A countdown appears in the LCD when powering on and off, allowing the transmitter to be turned on without RF for adjustments, and to prevent accidentally turning it off with momentary button presses.Power LEDThe PWR LED glows green when the battery is good. The color changes to red at a midpoint of the runtime as the battery voltage drops. When the LED begins to blink red, there is usually less than 30 minutes remain-ing with a lithium battery.The exact point at which the LED turns red will vary with battery brand and condition, temperature, and the out-put power setting. The LED is intended to simply catch your attention, not to be an exact indicator of remaining time. The illustration below depicts typical behavior with a lithium battery in the single battery model at 50 mW.1.61.41.21.0.82468HoursVoltageVariesGreen Red BlinkA weak battery will sometimes cause the PWR LED to glow green immediately after the transmitter is turned on, but will soon discharge to the point where the LED will turn red or the unit will turn off completely.Power LED Off FeatureIn normal operating mode, the UP and DOWN arrow buttons may be used to turn the PWR LED indica-tors off and on. This setting does not persist through a power cycle nor does it affect the LCD backlight.Audio Input JackThe Servo Bias input circuitry accommodates virtually every lavaliere, handheld or shotgun microphone avail-able, plus line level signals.Battery Compartment and Thumb ScrewThe large knurled thumbscrew is used to release or secure the Battery Compartment Cover Plate.Modulation LEDsProper input gain adjustment is critical to ensure the best audio quality. Two bicolor LEDs will glow either red or green to accurately indicate modulation levels. The input circuitry includes a wide range DSP controlled limiter to prevent distortion at high input levels.It is important to set the gain (audio level) high enough to achieve full modulation during louder peaks in the audio. The limiter can handle over 30 dB of level above full modulation, so with an optimum setting, the LEDs will flash red during use. If the LEDs never flash red, the gain is too low. In the table below, +0 dB indicates full modulation (-20 LED just turns red).Signal Level -20 LED -10 LEDLess than -20 dB Off Off-20 dB to -10 dB Green Off-10 dB to +0 dB Green Green+0 dB to +10 dB Red GreenGreater than +10 db Red RedAUDIO and FREQ ButtonsThe AUDIO button is used to display the audio level and low frequency roll-off settings. The UP and DOWN ar-row buttons adjust the values.The FREQ Button displays the selected operating frequency and toggles the LCD between displaying the actual operating frequency in MHz and a two-digit hexadecimal number that corresponds to the equivalent frequency switch setting on legacy transmitters.Pressing both buttons simultaneously enters the standby mode and turns the unit on and offUP/DOWN Arrow ButtonsThe UP and DOWN arrow buttons are used to select the values on the various setup screens and to lock out the control panel.AntennaThe transmitter uses a whip antenna with a flexible wo-ven, galvanized steel mesh cable and a standard SMA connector.Battery Compartment Thumb ScrewBattery Compartment Cover PlateAudio Input JackAUDIO Button FREQ ButtonModulation LEDsPWR LEDUP ArrowDOWN ArrowAntenna JackLCD
Super-Minature Belt Pack TransmitterRio Rancho, NM 7Battery and Battery Eliminator InstallationNote: Standard zinc-carbon batteries marked “heavy-duty” or “long-lasting” are not adequate.The battery status circuitry is designed for the voltage drop over the life of lithium batteries.To install new batteries:1. Turn the battery cover plate thumbscrew counter-clockwise a few turns until the door will rotate.2. Insert the new batteries into the housing. Polarity is marked on the back of the housing.3. Align the battery cover plate and tighten the battery cover plate thumbscrew.Two battery compartments (SMQV)Gore-Tex® covered ventPolarity engraved into housingDo Not Cover VentCover plate thumbscrewTo install the battery eliminator, loosen the thumbscrew completely and remove the battery door. Insert the battery eliminator and tighten the thumbscrew. Install plastic cap on dual battery model to cover the open battery compartment.Attaching and Removing the MicrophoneThe flexible sleeve over the 5-pin plug on the micro-phone helps prevent dust and moisture from getting into the input jack, and provides additional strain relief. The flange around the rim of the connector on the transmitter creates a splash proof connection and keeps the sleeve securely attached.The following procedure simplifies the attachment and removal of the microphone to assure the sleeve is seated securely.Align the latch on the plug and jack and insert the connector. It is easier to attach the microphone when the sleeve is pulled back as shown in the Step 3 photo below.1If the sleeve is pulled down and covering the connector, squeeze the end of the sleeve so you can feel the connector inside and press it into the jack until it latches.Pinch and squeeze the sleeve on this end to work it down over the flange.2Pinch and squeeze the sleeve near the flange and work it down with a kneading motion over the flange all the way around until it stays in place flush with the housing. Pull on the connector to make sure it is firmly latched.3Release buttonTo remove the connec-tor, pull the sleeve back to expose the black release button. Press the button to unlatch the plug.Gore - Tex Registered trademark of W. L. Gore and Associates
SMV SeriesLECTROSONICS, INC.8Operating InstructionsPower Up and Boot Sequence1) Ensure that good batteries are installed in the unit.2) Simultaneously press and hold the AUDIO and FREQ buttons until the power on boot sequence is initiated.The count will progress from 1 through 3 and the unit will then power up with the RF output turned on. During this turn on sequence, the modulation and power LEDs all glow red, then green, and then revert to normal operation. If the buttons are released before the count is complete, the unit will boot up into the standby mode (see below). The LCD displays the following information during the boot sequence:Company Name: LECtroFrequency Block and Firmware Version (rX.X):941r1.1 (typical)Compatibility Mode: CP nHb (typical)Power Level Pr 100 (as set)Audio: Aud 22 (as set)Power DownInitial Power OffTimer Screen1) Simultaneously press and hold the AUDIO and FREQ buttons while observing that the word “Off” appears in the LCD along with a counter.2) When the counter reaches “0”, the unit turns off.Note: If the AUDIO and FREQ buttons are released before the LCD goes blank at the end of the countdown, the unit will not turn off. Instead, it will stay energized and the display will return to the previous screen.Standby ModeStandby ScreenWith the power turned off, pressing the AUDIO and FREQ buttons briefly places the unit in Standby Mode.In this mode the RF output is turned off so all setup adjustments can be made without interfering with other systems operating in the same location. The screen displays “rf OFF” to remind the user that the unit is not transmitting.While the unit is in the standby mode, access the setup screens using the AUDIO and FREQ buttons and make adjustments using the UP and DOWN arrows.MenusSetup is accomplished using menus and setup screens accessed by holding the UP and DOWN arrow buttons at turn on, and by pressing the AUDIO and FREQ but-tons when the unit is turned on.Hold UP arrow at turn on.Hold the UP arrow button in while pressing both AUDIO and FREQ buttons to access the setup screens below. It’s easier if you lay the unit on a flat surface and use two hands to press all three buttons at the same time. After the first screen loads, press the AUDIO button repeatedly to switch between the settings. Press the UP and DOWN arrow buttons for the desired selection.After the settings are made, press both AUDIO and FREQ buttons together to exit and turn the power off.CP (compatibility modes) Allows the transmitter to be used with 941 Series re-ceivers or IFB systems in the 941 MHz band. nHb new hybrid mode (ETSI compliant)IFb Lectrosonics IFB systemsNOTE: The nHb compatibility mode is the same as the NU HYBR mode in the SRc-941 receiver.Pr (power output) Can be set at 100 for slightly increased range or at 50 for longer battery life. 50 50 mW output and longer battery life when maximum range is not necessary100 100 mW for slightly increased rangeNOTE: See battery life table in the specificationsbL (backlight settings) Adjusts how long the LCD stays lit after pressing buttons.55 minutes30 30 secondson Stays onStP (Frequency step size)Sets the increments of frequency adjustment.100 100 kHz steps25 25 kHz steps
Super-Minature Belt Pack TransmitterRio Rancho, NM 9Hold DOWN arrow at turn on.Hold the DOWN arrow button in while pressing both AUDIO and FREQ buttons to access the setup screens below. It’s easier if you lay the unit on a flat surface and use two hands to press all three buttons at the same time. After the first screen loads, press the AUDIO but-ton repeatedly to switch between the settings. Press the UP and DOWN arrow buttons for the desired selection.After the settings are made, press both AUDIO and FREQ buttons together to exit and turn the power off.rc (remote control with mobile app)Allows the transmitter to respond to remote control “dweedle” tones from a mobile device, or from tones generated by the Lectrosonics RM and RM2 devices.on Enables the remote function.oFF Disables the remote function.NOTE: See page 10 for detailsPbAc (auto power restore)Sets the transmitter to automatically turn back on and return to the previous state after a battery change or power interruption when it is in the operating mode. This is convenient when the transmitter is powered by an external source.1 Restores power automatically0 Does not restore power automaticallyAUDIO ButtonWhen the unit is turned on in either the Standby or Operating Mode, pressing the AUDIO button repeatedly switches between the available settings.• LF (XX) adjusts the low frequency roll-off of the audio signal.• AUD (XX) adjusts the input gainLF (XX) - Adjusting the Low Frequency Roll-offRepeatedly press the AUDIO button until the LF roll-off adjustment screen appears. Then press and hold the AUDIO button while selecting the desired roll-off frequency with the UP and DOWN arrows.The roll-off frequency can be set to 35, 50, 70, 100, 120 and 150 Hz.AUD (XX) - Adjusting Audio Level (Gain)The control panel modulation LEDs marked -10 and -20 indicate the audio level and limiter activity. Once adjust-ed according to the following procedure, the transmit-ter’s audio level setting should not be used to control the volume of your sound system or recorder levels. This gain adjustment matches the transmitter gain with the microphone’s output level, the user’s voice level and the position of the microphone. The audio input level (gain) should be adjusted with the unit in the Standby Mode while observing the LEDs.It is generally best to set the LF roll-off before adjust-ing the gain, since low frequency energy can affect the input level to the transmitter.It is desirable to to set the gain so that some limiting occurs on louder peaks. The limiter is very transparent over a 43 dB range, and its effect is not audible until the system is close to overload. In other words, don’t be shy about turning up the gain.It is actually a good idea to turn the gain up to maxi-mum and listen for distortion or compression to get a feel for how much headroom is available.Signal Level -20 LED -10 LEDLess than -20 dB Off Off-20 dB to -10 dB Green Off-10 dB to +0 dB Green Green+0 dB to +10 dB Red GreenGreater than +10 dB Red RedNote: If several different people will be using the transmitter and there is not time to make the adjustment for each indi-vidual, adjust it for the loudest voice.1) With the transmitter in the Standby Mode, plug in the microphone and make sure the connector is firmly seated.Warning: If the wireless system is powered up while connected to a live sound system, be careful to turn the sound system level down first or severe feedback can occur.2) Position the microphone in the location where it will be used in actual operation.3) Observe the modulation LEDs while speaking or singing into the microphone at the same voice level that will be used during operation. While holding the AUDIO button, press the UP or DOWN arrow buttons until the both the -20 and -10 LEDs glow green, with the -20 LED flickering red during louder peaks in the audio. This will maximize the signal to noise ratio of the system with full modulation.4) If the unit was set up in Standby Mode, it will be necessary to turn the transmitter off, then power it up again in normal operation so the RF output will be on. Then the other components in the sound or recording system can be adjusted.
SMV SeriesLECTROSONICS, INC.10FREQ ButtonThe operating frequency can be adjusted according to the frequency in MHz or a two-digit hexadecimal code. Press the button repeatedly to switch between the two displays. The display switches when the button is first pushed; push and hold the button in the desired mode and use the UP and DOWN arrow buttons to make the adjustment.In this example, the same frequency is displayed in MHz and the equivalent hex code.The hex code is a hexadecimal sequence that pro-gresses upward from lowest to highest frequency using the numerals and letters from 0 through F. When the frequency is on a 100 kHz step, the hex code is only two digits, as shown above, which is easy to remember. When the step size is set to 25 kHz, additional charac-ters are used to denote the exact frequency with four characters.Locking/Unlocking the Control PanelSimultaneously pressing and holding both the UP and DOWN arrow buttons during normal operation starts the Lock timer. The timer starts at three and counts down to zero.When the timer reaches zero, the buttons on the control panel are locked.With the controls locked, the AUDIO and FREQ buttons can still be used to display current settings. Any attempt to change a setting by pressing either the UP or DOWN arrow button will result in an on-screen Loc reminder that the controls are locked. Remove the batteries to unlock the control panel.Important: Once the transmitter is locked, it cannot be unlocked or powered off using the buttons. The only ways to unlock a locked transmitter are to remove the battery or unlock it via the RM remote control.Remote Control OperationRemote Control ScreensThe transmitter can be controlled by signals from audio “dweedle” tones generated by a mobile phone, or with the Lectrosonics RM and RM2 devices.The remote function is enabled in the UP arrow power on options (see previous section). If a remote control signal is detected but the function is no enabled, the message rc oFF will be displayed briefly on the trans-mitter’s LCD.Remote functions available are:• Tx Input Gain• Sleep/Unsleep• Lock/Unlock• Frequency• Tuning in 25 kHz steps• Changing the low frequency roll-off setting• Turning on/off the PWR and Audio LEDs• Input gain functions In sleep mode, the transmitter uses about 20% of the normal amount of battery drain. Sleep mode can only be invoked with the remote control, and can only be revoked with the remote control or by removing the battery. When in the sleep mode, the PWR LED blinks green every few seconds to indicate that the transmitter is asleep and not turned off.
Super-Minature Belt Pack TransmitterRio Rancho, NM 115-Pin Input Jack WiringThe wiring diagrams included in this section represent the basic wiring necessary for the most common types of microphones and other audio inputs. Some micro-phones may require extra jumpers or a slight variation on the diagrams shown.It is virtually impossible to keep completely up to date on changes that other manufacturers make to their products, thus you may encounter a microphone that differs from these instructions. If this occurs please call our toll-free number listed under Service and Repair in this manual or visit our web site at: www.lectrosonics.comSM Equivalent Input Circuit Wiring10k1k54321To Virtual GroundAudio AmplifierBIASMICBIAS SELECTLINE INGND+30uF+5 VDCServo BiasPin 4 to Pin 1 = 0 V Pin 4 Open = 2 VPin 4 to Pin 2 = 4 V+To Limiter Control30uF500 Ohm100 Ohm2.7K200 Ohm+3.3uF100 OhmAudio input jack wiring:PIN 1 Shield (ground) for positive biased electret lava-liere microphones. Shield (ground) for dynamic microphones and line level inputs.PIN 2 Bias voltage source for positive biased electret lavaliere microphones.PIN 3 Low impedance microphone level input for dynamic microphones. Also accepts hand-held electret microphones provided the microphone has its own built-in battery.PIN 4 Bias voltage selector for Pin 3. Pin 3 voltage (0, 2 or 4 volts) depends on Pin 4 connection.Pin 4 tied to Pin 1: 0 VPin 4 Open: 2 VPin 4 to Pin 2: 4 VPIN 5 High impedance, line level input for tape decks, mixer outputs, musical instruments, etc. Installing the Connector:1) If necessary, remove old connector from microphone cable.2) Slide Rubber Boot onto microphone cable with the large end facing away from the microphone. (See illus-tration above.)3) If necessary, slide the 1/8-inch black shrink tubing onto the mircrophone cable. (This tubing is needed for some cables to ensure the cable fits snugly in the rubber boot.)4) Use the resistors and connector included with this kit to configure the TA5F to your particular microphone. (See Wiring Diagrams below.) A length of .065 OD clear tubing is included if insulating the resistor leads or shield wire is necessary. (Remove rubber strain relief from connector backshell by pulling it out of the backshell.)5) Slide the Strain Relief over the TA5F Insert and crimp as shown to the right. Then insert the TA5F Insert and Strain Relief in the TA5F Latchlock. Screw the TA5F Flex Relief onto the TA5F Latchlock.6) If needed, position and shrink the 1/8-inch shrink tub-ing on the microphone cable, then slide the Rubber Boot down over the TA5F connector.Line Level SignalsThe normal hookup for line level signals is: Signal Hot to pin 5, Signal Gnd to pin 1 and pin 4 jumped to pin 1. This allows signal levels up to 3V RMS to be applied without limiting.If more headroom is needed, insert a 20 k resistor in series with pin 5. Put this resistor inside the TA5F con-nector to minimize noise pickup.TA5F LatchlockInsertInsulator Strain ReliefTA5F Backshell with Strain ReliefRemove strain relief if using dust bootTA5F Backshell(Strain Relief removed) Dust Boot (P/N 35510)Note: If you use the dust boot, remove the rubber strain relief that is attached to the TA5F cap, or the boot will not fit over the assembly.SMKITTA5 Connector kit for SMV series transmitters, 5-pin TA5F plug with sleeve
SMV SeriesLECTROSONICS, INC.12NOTE: This termination is intended for UHF transmitters only. VHF transmitters with 5-pin jacks require a different termination. Lectrosonics lavaliere microphones are terminated for compatibility with VHF and UHF transmitters, which is different than what is shown here.Microphone Cable Termination for Non-Lectrosonics MicrophonesTA5F Connector AssemblyMic Cord Stripping Instructions12345VIEW FROM SOLDERSIDE OF PINS0.3"0.15"Crimping to Shield and InsulationShieldInsulationStrip and position the cable so that the clamp can be crimped to contact both the mic cable shield and the insulation. The shield contact reduces noise with some microphones and the insulation clamp increases ruggedness.Crimp these fingers to contact the shieldCrimp these fingers to clamp the insulation
Super-Minature Belt Pack TransmitterRio Rancho, NM 13Microphone RF BypassingWhen used on a wireless transmitter, the microphone element is in the proximity of the RF coming from the transmitter. The nature of electret microphones makes them sensitive to RF, which can cause problems with the microphone/transmitter compatibility. If the electret microphone is not designed properly for use with wire-less transmitters, it may be necessary to install a chip capacitor in the mic capsule or connector to block the RF from entering the electret capsule.Some mics require RF protection to keep the radio signal from affecting the capsule, even though the transmitter input circuitry is already RF bypassed (see schematic diagram).If the mic is wired as directed, and you are having dif-ficulty with squealing, high noise, or poor frequency response, RF is likely to be the cause.The best RF protection is accomplished by installing RF bypass capacitors at the mic capsule. If this is not pos-sible, or if you are still having problems, capacitors can be installed on the mic pins inside the TA5F connector housing.3 WIRE MIC2 WIRE MICCAPSULE CAPSULESHIELDAUDIOSHIELDAUDIOBIASAlternate locations for bypass capacitorsTA5FCONNECTORTA 5FCONNECTORPreferred locations for bypass capacitorsInstall the capacitors as follows: Use 330 pF capaci-tors. Capacitors are available from Lectrosonics. Please specify the part number for the desired lead style. Leaded capacitors: P/N 15117 Leadless capacitors: P/N SCC330PAll Lectrosonics lavaliere mics are already bypassed and do not need any additional capacitors installed for proper operation.
SMV SeriesLECTROSONICS, INC.14BALANCED AND FLOATING LINE LEVEL SIGNALS*NOTE: If the output is balanced but center tapped to ground, such as on all Lectrosonics receivers, do not connect Pin 3 of the XLR jack to Pin 4 of the TA 5F connector.TA5F PLUGXLR JACKFig. 7Compatible Wiring for Both Servo Bias Inputs and Earlier Transmitters:Simple Wiring - Can ONLY be used with Servo Bias Inputs:Servo Bias was introduced in 2005 and all transmit-ters have been built with this feature since 2007.Wiring Hookups for Different SourcesIn addition to the microphone and line level wiring hook-ups illustrated below, Lectrosonics makes a number of cables and adapters for other situations such as con-necting musical instruments (guitars, bass guitars, etc.) to the transmitter. Visit www.lectrosonics.com and click on Accessories, or download the master catalog.A lot of information regarding microphone wiring is also available in the FAQ section of the web site at:http://www.lectrosonics.com/faqdbFollow the instructions to search by model number or other search options.4 VOLT POSITIVE BIAS 2-WIRE ELECTRETMost common type of wiring forlavaliere mics. This is the wiring for the Lectrosonics M152 lavaliere microphone.Fig. 2SHIELD TIP PIN 5 4 3 2 1 SLEEVE LINE LEVEL RCA or 1/4” PLUG A UDI O 1 2 3 4 5 T A5 F PLUG UNBALANCED LINE LEVEL SIGNALSFor signal levels up to 3V (+12 dBu) before limiting. Fully compatible with 5-pin inputs on other Lectrosonics transmitters such as the LM and UM Series. A 20k ohm resistor can be inserted in series with Pin 5 for an additional 20 dB of attenuation to handle up to 30V (+32 dBu).Fig. 812345PINSHIELDAUDIO1 2 3 4 5 T A5 F PLUG 2.7 k2 VOLT NEGATIVE BIAS 2-WIRE ELECTRETCompatible wiring for microphones such as negative bias TRAM models.NOTE: The resistor value can range from 2k to 4k ohms.Fig. 4Fig. 114 VOLT POSITIVE BIAS 3-WIRE ELECTRETNOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring.2 VOLT POSITIVE BIAS 2-WIRE ELECTRETSimplified wiring for microphones such as Countryman B6 Lavalier and E6 Earset models and others.NOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring.Fig. 9Fig. 3 - DPA MicrophonesDANISH PRO AUDIO MINIATURE MODELSThis wiring is for DPA lavalier and headset microphones.NOTE: The resistor value can range from 3k to 4k ohms.Same as DPA adapter DAD3056Fig. 102 VOLT NEGATIVE BIAS 2-WIRE ELECTRETSimplified wiring for microphones such as negative bias TRAM.NOTE: This servo bias wiring is not compatible with earlier versions of Lectrosonics transmitters. Check with the factory to confirm which models can use this wiring.Fig. 6LO-Z MICROPHONE LEVEL SIGNALSFor low impedance dynamic mics or electret mics with internal battery or power supply.XLR JACKInsert 1k resistor in series with pin 3 if attenuation is neededFig. 11 2 3 4 5 PIN SHIELD A UDI O 1 2 3 4 5 T A5 F PLUG 3.3 k1.5 k 2 VOLT POSITIVE BIAS 2-WIRE ELECTRET Compatible wiring for microphones such as Countryman E6 headworn and B6 lavaliere. Also see Fig. 9Fig. 5 - Sanken COS-11 and othersDRAIN (BIAS)SOURCE (AUDIO)SHIELD4 VOLT POSITIVE BIAS 3-WIRE ELECTRET WITH EXTERNAL RESISTORAlso used for other 3-wire lavaliere microphones that require an external resistor.
Super-Minature Belt Pack TransmitterRio Rancho, NM 15Silver Paste on SM Series Transmitter ThumbscrewsSilver paste is applied to thumbscrew threads on new units at the factory to improve the electrical connection from the battery compartment through the housing on any SM Series transmitter. This applies to the standard battery door and the battery eliminator.Threads provide electrical contactThe small vial contains a tiny amount (25 mg) of silver conductive paste. A small speck of this paste will im-prove the conductivity between the battery cover plate thumbscrew and the case of the transmitter.The tiny vial is about 1/2 inch tall and contains 25 mg of silver paste.With improved conductivity (lower resistance) more of the battery voltage can get to the internal power sup-plies causing reduced current drain and longer battery life. Though the amount seems very small, it is enough for years of use. It is, in fact, 25 times the amount that we use on the thumbscrews at the factory.To apply the silver paste, first completely remove the cover plate from the SM housing by backing the thumb-screw completely out of the case. Use a clean, soft cloth to clean the threads of the thumbscrew.NOTE: DO NOT use alcohol or a liquid cleaner.Simply hold the cloth around the threads and turn the thumbscrew. Move to a new spot on the cloth and do it again. Do this until the cloth remains clean. Now, clean the threads in the case by using a dry cotton swab (Q-tip) or equivalent. Again, clean the case threads until a fresh cotton swab comes away clean.Open the vial, and transfer a pinhead speck of silver paste to the second thread from the end of the thumb-screw. A easy way to pickup a speck of paste is to partially unfold a paper clip and use the end of the wire to acquire a tiny bit of paste. A toothpick will also work. An amount that covers the end of the wire is sufficient.Apply paste to second thread from end of thumbscrewIt is not necessary to spread the paste more than a little bit on the thread as the paste will spread itself every time the thumbscrew is screwed in and out of the case during battery changes.Do not apply the paste to any other surfaces. The cover plate itself can be cleaned with a clean cloth by rubbing the slightly raised rings on the plate where it contacts the battery terminal. All you want to do is to remove any oils or dirt on the rings. Do not abrade these surfaces with a harsh material such as a pencil eraser, emery paper, etc., as this will remove the conductive nickel plating and expose the underlying aluminum, which is a poor contact conductor.
SMV SeriesLECTROSONICS, INC.16LectroRMBy New Endian LLCLectroRM is a mobile application for iOS and Android operating systems. Its purpose is to remotely control Lectrosonics transmitters, including: • SM Series • WM • L Series The app remotely changes settings on the transmit-ter through the use of encoded audio tones, which when received by the attached microphone, will alter the configured setting. The app was released by New Endian, LLC in September 2011. The app is available for download and sells for about $20 on the Apple App Store and Google Play Store.LectroRM’s remote control mechanism is the use of an audio sequence of tones (dweedles) that are inter-preted by the transmitter as a configuration change. The settings available in LectroRM are: • Audio Input Gain • Frequency • Sleep/Unsleep • Lock Mode • Power Output • Low Frequency Roll-off • LEDs On/OffUser InterfaceThe user interface involves selecting the audio se-quence related to the desired change. Each version has an interface for selecting the desired setting and the desired option for that setting. Each version also has a mechanism to prevent accidental activation of the tone.iOS The iPhone version keeps each available setting on a separate page with the list of options for that setting. On iOS, the “Activate” toggle switch must be enabled to show the button which will then activate the audio. The iOS version’s default orientation is upside-down but can be configured to orient right-side up. The purpose for this is to orient the device’s speaker, which is at the bot-tom of the device, closer to the transmitter microphone.Android The Android version keeps all settings on the same page and allows the user to toggle between the activa-tion buttons for each setting. The activation button must be long pressed to activate. The Android version also allows users to keep a configurable list of full sets of settings. ActivationFor a transmitter to respond to remote control audio tones, the transmitter must meet certain requirements:• The transmitter must not be turned off; it can how-ever be in sleep mode.• The transmitter must have a firmware version that includes the remote control functions.• The remote control mode must be enabled in the setup screen.• The transmitter microphone must be within range.Please be aware this app is not a Lectrosonics product. It is privately owned and operated by New Endian LLC, www.newendian.com.
Super-Minature Belt Pack TransmitterRio Rancho, NM 17Accessories for single battery models:PSM Leather pouch with integrated belt clipSMBCUPSL Spring-loaded machined alumi-num clip for SMV; antenna extending upwardSMBCDNSL Spring-loaded, machined aluminum clip for SMV; antenna extending downwardSMBCDN Wire belt clip for SMV trans-mitters; antenna extending downwardSMBCUP Machined, wire belt clip for SMV transmitters; antenna extending upAccessories for dual battery models:PSMD Leather pouch with integrated belt clipSMDBCSL Spring-loaded machined aluminum clip for SMQV; fits for anten-na extending upward or downwardSMDBC Wire belt clip for SMQV trans-mitters35924 Thermal insu-lating pad for SMV and SMQV; adhesive backing
SMV SeriesLECTROSONICS, INC.18Accessories for Both ModelsSMBATELIM External power adapter (battery elimina-tor) for all SM Series transmitters. 6 to 36 volt external sources. Handles up to 1 amp consumption. Protected against shorts and reverse polarity.To install the battery eliminator, loosen the thumbscrew completely and remove the battery door. Insert the bat-tery eliminator and tighten the thumbscrew. SMKITTA5 Microphone connector kit with watertight sleeve for all SM Series transmitters.AMM944 Whip antenna for 941 MHz transmitters
Super-Minature Belt Pack TransmitterRio Rancho, NM 19Specifications and FeaturesSpecificationsOperating Frequency Range: 941.525 - 951.975 MHz 952.875 - 956.225 MHz 956.475 - 959.825 MHz Channel Spacing: Selectable; 25 or 100 kHzFrequency selection: Control panel membrane switchesRF Power output: Switchable; 50 or 100 mWPilot tone: 27 to 32 kHz; 3 kHz deviation (Digital Hybrid mode)Frequency stability: ± 0.002%Spurious radiation: Compliant with ETSI EN300 422-1 v1.4.2Equivalent input noise: –125 dBV, A-weightedInput level: Dynamic mic: 0.5 mV to 50 mV before limiting Greater than 1 V with limiting Electret lavaliere mic: 1.7 uA to 170 uA before limiting. Greater than 5000 uA (5 mA) with limiting. Line level: 17 mV to 1.7 V before limiting. Greater than 50 V with limiting.Input impedance: Dynamic mic: 300 Ohms Electret lavaliere: Input is virtual ground with servo adjusted constant current bias Line level: 2.7 k OhmsInput limiter: Soft limiter, 30 dB rangeBias voltages: • Fixed 5 V at up to 5 mA • Selectable 2 V or 4 V servo bias for electret lavaliereInput gain control range: 44 dB in 1 dB stepsModulation indicators: Dual bicolor LEDs indicate modulation of –20, -10, 0, +10 dB referenced to full modulation.Controls: Control panel with LCD and four membrane switches.Audio Performance (overall system): Frequency Response: 35 Hz to 20 kHz, +/-1 dB Low frequency roll-off: Adjustable from 35 to 150 Hz THD: 0.2% (typ.) 100 Hz to 20 kHz System Dynamic Range: SmartNR no limiting w/limitingOFF 103.5 108.0NORMAL 107.0 111.5FULL 108.5 113.0Note: The dual envelope “soft” limiter provides exceptionally good handling of transients using variable attack and release time constants. Once activated, the limiter compresses 30+ dB of transmitter input range into 4.5 dB of receiver output range, thus reducing the measured figure for SNR without limiting by 4.5 dB.The battery door rotates to open and close on the transmitters. A knurled knob is tightened to maintain pres-sure on the battery contacts. O-rings around the battery contacts block moisture and dust from entering the battery compartments.SMV modelSMQV modelAudio Input Jack: Switchcraft 5-pin locking (TA5F)Antenna: Flexible, unbreakable steel cable.Batteries: 1.5 Volt AA lithiumBattery Life: SMV-941 50 mW (1 AA): 7.25 hrsSMV-941 100 mW (1 AA): 5.5 hrsSMQV-941 50 mW (2 AA): 14.5 hrsSMQV-941 100 mW (2 AA): 14 hrs Weight: SMV: 2.7 oz.. (75.9 grams) with lithium battery SMQV 3.7 oz.. (105 grams) with lithium batteriesOverall Dimensions: SMV: 2.3 x 1.8 x 0.64 inches (58 x 46 x 16 mm) (not including microphone) SMQV: 2.3 x 2.4 x 0.64 inches (58 x 60 x 16 mm (not including microphone)Emission Designator: 180KF3ESpecifications subject to change without notice.
SMV SeriesLECTROSONICS, INC.20Before going through the following chart, be sure that you have a good battery in the transmitter. It is important that you follow these steps in the sequence listed.SYMPTOM POSSIBLE CAUSETRANSMITTER PWR LED OFF 1) Battery is inserted backwards or dead. 2) Transmitter not powered up.TRANSMITTER PWR LED BLINKS GREEN EVERY FEW SECONDS, TRANSMITTER DOES NOT RESPOND OTHERWISE 1) Transmitter has been put to sleep by the remote control. Either use the remote control to wake it up or remove and reinsert the transmitter’s battery.AUDIO LEVEL LEDs NOT LIGHTING 1) Gain control set to low or at minimum. 2) Batteries are dead or installed backwards. Check PWR LED. 3) Mic capsule is damaged or malfunctioning. 4) Mic cable damaged or mis-wired.RECEIVER RF INDICATOR OFF 1) Transmitter not turned on, or is in Standby Mode. 2) Transmitter battery is dead. 3) Receiver antenna missing or improperly positioned. 4) Transmitter and receiver not on same frequency. Check switches/display on transmitter and receiver. 5) Operating range is too great. 6) Defective transmitter or receiver antenna. NO SOUND (OR LOW SOUND LEVEL), RECEIVER INDICATES PROPER AUDIO MODULATION 1) Receiver output level set too low. 2) Receiver output disconnected, or cable defective or mis-wired. 3) Sound system or recorder input is turned down.DISTORTED SOUND 1) Transmitter gain (audio level) is far too high. Check audio level LEDs and receiver audio levels during use. 2) Receiver output may be mismatched with the sound system or recorder input. Adjust output level on receiver to the correct level for the recorder, mixer or sound system. (Use the receiver’s Tone function to check level.) 3) Transmitter is not set to same frequency as receiver. Check that operating frequency on receiver and transmitter match. 4) Receiver/Transmitter Compatibility Mode mismatched. EXCESSIVE FEEDBACK 1) Transmitter gain (audio level) too high. Check gain adjustment and/or reduce receiver output level. 2) Talent standing too close to speaker system. 3) Mic is too far from user’s mouth.Troubleshooting
Super-Minature Belt Pack TransmitterRio Rancho, NM 21SYMPTOM POSSIBLE CAUSEHISS AND NOISE -- AUDIBLE DROPOUTS 1) Transmitter gain (audio level) far too low. 2) Defective transmitter or receiver antenna. 3) Operating range too great. 4) Signal interference. Turn off transmitter. If receiver’s signal strength indicator does not drop to nearly zero, this indicates an interfering signal may be the problem. Try a different operating frequency.“Loc” APPEARS IN DISPLAY WHEN ANY BUTTON IS PRESSED 1) Control Panel is locked. 2) Unlock the control panel with remote or removing and replacing the batteries.“Hold” APPEARS IN DISPLAY WHEN ARROW BUTTONS ARE PRESSED 1) Reminder that it is necessary to hold down the AUDIO or FREQ button to make adjustments to the audio gain or frequency settings.“PLL” APPEARS IN DISPLAY 1) Indication that the PLL is not locked. This is a serious condition that requires factory repair. It may be possible to operate on another frequency far removed from the one that was selected when PLL appeared on the display.TRANSMITTER WON’T RESPOND TO REMOTE CONTROL 1) If LCD blinks “rc oFF”, transmitter has not been configured to respond to the remote control. 2) If LCD blinks “- - - - - -”, transmitter is already set as requested by the remote control. 3) If transmitter does not respond at all, try moving the remote control closer to the microphone or increasing the remote control’s loudness setting, or increasing the input gain on the transmitter. 4) Make sure volume of the remote device and proximity of microphone are sufficient to engage transmitter. 5) Make sure transmitter is not in Sleep mode.
SMV SeriesLECTROSONICS, INC.22Service and RepairIf your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the Troubleshooting section in this manual.We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop at-tempt anything other than the simplest repair. If the repair is more complicated than a broken wire or loose connection, send the unit to the factory for repair and service. Don’t attempt to adjust any controls inside the units. Once set at the factory, the various controls and trimmers do not drift with age or vibration and never require readjustment. There are no adjustments inside that will make a malfunctioning unit start working.LECTROSONICS’ Service Department is equipped and staffed to quickly repair your equipment. In warranty repairs are made at no charge in accordance with the terms of the warranty. Out-of-warranty repairs are charged at a modest flat rate plus parts and shipping. Since it takes almost as much time and effort to determine what is wrong as it does to make the repair, there is a charge for an exact quotation. We will be happy to quote approximate charges by phone for out-of-warranty repairs.Returning Units for RepairFor timely service, please follow the steps below:A. DO NOT return equipment to the factory for repair without first contacting us by email or by phone. We need to know the nature of the problem, the model number and the serial number of the equipment. We also need a phone number where you can be reached 8 A.M. to 4 P.M. (U.S. Mountain Standard Time).B. After receiving your request, we will issue you a return authorization number (R.A.). This number will help speed your repair through our receiving and repair departments. The return authorization number must be clearly shown on the outside of the shipping container.C. Pack the equipment carefully and ship to us, shipping costs prepaid. If necessary, we can provide you with the proper packing materials. UPS is usually the best way to ship the units. Heavy units should be “double-boxed” for safe transport.D. We also strongly recommend that you insure the equipment, since we cannot be responsible for loss of or dam-age to equipment that you ship. Of course, we insure the equipment when we ship it back to you.Lectrosonics USA:Mailing address: Shipping address: Telephone: Lectrosonics, Inc. Lectrosonics, Inc. (505) 892-4501 PO Box 15900 581 Laser Rd. (800) 821-1121 Toll-free Rio Rancho, NM 87174 Rio Rancho, NM 87124 (505) 892-6243 Fax USA USA Web: E-mail: www.lectrosonics.com sales@lectrosonics.comLectrosonics Canada:Mailing Address: Telephone: E-mail: 720 Spadina Avenue, (416) 596-2202 Sales: colinb@lectrosonics.com Suite 600 (877) 753-2876 Toll-free Service: joeb@lectrosonics.com Toronto, Ontario M5S 2T9 (877-7LECTRO) (416) 596-6648 Fax
581 Laser Road NE • Rio Rancho, NM 87124 USA • www.lectrosonics.com(505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 • sales@lectrosonics.comLIMITED ONE YEAR WARRANTYThe equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment.Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor. If Lectrosonics, Inc. cannot correct the defect in your equipment, it will be replaced at no charge with a similar new item. Lectrosonics, Inc. will pay for the cost of returning your equipment to you.This warranty applies only to items returned to Lectrosonics, Inc. or an authorized dealer, shipping costs prepaid, within one year from the date of purchase.This Limited Warranty is governed by the laws of the State of New Mexico. It states the entire liablility of Lectrosonics Inc. and the entire remedy of the purchaser for any breach of warranty as outlined above. NEITHER LECTROSONICS, INC. NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS, INC. EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT.This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state.8 November 2017

Navigation menu