Leedarson Lighting 6VY-A806ST-Q1R LED lamp User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3344890
Application ID	lfgTMXn3sfsRa5qBOM+teg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.58kB (244783 bits)
Date Submitted	2017-04-05 00:00:00
Date Available	2017-04-07 00:00:00
Creation Date	2017-03-16 14:24:25
Document Lastmod	2017-03-16 14:24:25
Document Title	主板规格
Document Creator	WPS Office
Document Author:	微软用户

Leedarson LED Bulb DIM
Quick User Guide
Draft
Ver.
Fu
V1.0
Leedarson Lighting
Description
Time
2016.12.12
1 Product Introduction
1.1 Basic Information
CONTROL YOUR LIGHTS FROM ANYWHERE in the world from the palm of your hand. The
DIM Retrofit produces beautiful high quality light that you can tune, dim, and control from your
smartphone or tablet. Easy to setup, bulbs fit into your standard household sockets - no need for
installation by an electrician. A wireless network is required to operate bulbs.
SET LIGHT SCENES: Create rich indirect light scenes in your home by dim the light. Schedule to
turn on the lights so you don't come home to a dark house. Set automated timers, or program the bulb
to gradually increase brightness in the the morning like the sunrise for a more pleasant, natural alarm.
SAVE ENERGY: Lightify bulbs use up to 84% less energy than traditional incandescent bulbs and last
up to 20,000 hours making them a smart choice for energy conscious homes.
1.2 Special notes for Connected Bulbs
Line Voltage Dimmer
LEEDARSON does not recommended the use of a line voltage dimmer with connected bulbs.The
reason is that each connected bulb contains a radio and by reducing,or removing,power through a line
voltage dimmer may cause the connected bulb to not function properly.
For dimming, LEEDARSON recommends using a compatible App (i.e., LEEDARSON’S LDS App)or
a compatible wireless switch that uses the same wireless protocol as the bulb.
1.3 Leave your fixture on
If your switch or fixture is OFF,or is turned OFF, then control and communication from the App, or
wireless switch, to the LED Bulb is lost.
Leedarson Lighting
Inclusion Procedure
The following are the general procedures for the Z-Wave bulb to be “included” into the network:
1. Screw the DIM bulb into a standard E27 socket.
2. Turn on the bulb with your wall switch to apply power to the bulb.
a) If you’re not using a wall switch, then use your alternate method to apply power to the bulb.
3. Activate the “inclusion”mode on your Z-wave controller or gateway.
a) This may also be done through your associated app,if your ecosystem has that capability.
4. Toggle the wall-switch, from OFF, then to ON.
a) Or use your alternate method to toggle power from OFF, then to ON.
5. The LED bulb will flash once if it has been successfully “included”into your Z-Wave network.
Note: If you are using 3rdpartyZ-Wave Controller or Gateway, please refer to 3rdParty’s instruction on
how to add a new devices to your network.
Note 2: If the bulb will not join the network after repeated attempts, please use the Factory Reset
procedures to clear the bulb’s settings.
1.4 Factory Reset Procedure
Physically switch the bulb on and off six (6) times for intervals of 0.5-2seconds. After the 6thtime, the
bulb will flash twice indicating that it’s successfully reset.
Leedarson Lighting
1.5 Behaviors of the bulb
This bulb has some behaviors to indicate users the status of the bulb.
1.5.1 Factory Reset mode
The bulb will flash twice when it is powered on in reset mode or factory mode.
1.5.2 Inclusion Mode
The A19 bulb will flash once when it has been included into the network.
1.5.3 Exclusion Mode
The A19 bulb will flash once and then dim to 5% when it has been excluded outside the network. If
you want the bulb to be re-included, you need re-power the bulb, and then execute the inclusion
process.
1.6 Technical Parameter
Protocol
Frequency
Communication Distance
Modulation Mode
Power(W)
Voltage(V)
Dim Range
CCT(K)
CRI
Beam Angle
Dimensions(mm)
Leedarson Lighting
Z-Wave
908.42MHz
40m(LOS)
FSK(BFSK/GFSK)
100-240
5-100%
2700
80
240
120*60
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
3.NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help
- This device and its antenna(s) must not be co-located or operating in conjunction with any
other antenna or transmitter.
Leedarson Lighting

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 5
Author                          : 微软用户
Comments                        : 
Company                         : 
Create Date                     : 2017:03:16 14:24:25+06:24
Creator                         : WPS Office
Modify Date                     : 2017:03:16 14:24:25+06:24
Producer                        : 
Source Modified                 : D:20170316142425+06'24'
Subject                         : 
Title                           : 主板规格
Trapped                         : false

EXIF Metadata provided by EXIF.tools