Leica Geosystems CPD LD3BT Laser Distance Meter User Manual My
Leica Geosystems AG, CPD Laser Distance Meter My
User man
Leica DISTOTM X4 The original laser distance meter Overview Technical data Instrument Set-up Settings Operations Message Codes Care Warranty Safety instructions Leica DISTO™ X4 10 27 53 54 55 56 Overview Ov e rv ie w Components 5 Add/ Navigate left The Leica DISTO™ is a laser distance meter operating with a class 2 laser. See chapter Technical data for scope of use. 6 Enter/ Equal Basic result screen 7 Selection keys linked to symbols above 8 Functions 9 Subtract/ Navigate right 10 Measuring reference/ Navigate downwards 1 Status bar 2 Main line 3 Active function 4 Favorites 1 Display 2 ON/ Measure 3 Clear/ OFF 4 Zoom/ Navigate upwards Leica DISTO™ X4 Overview Basic measuring screen Selection screen Icons on status bar Scroll down for further results Battery power Bluetooth® is switched on Bluetooth® connection established Measuring reference Device is measuring Offset is activated and adds/substracts the defined value from measuring distance Device is levelled Device is not levelled Zoom 1 Status bar 3 Active function 4 Favorites 5 Zoom stage 1 Function/ Settings 2 Settings 3 Help function 4 Page indicator 6 Cross hair Leica DISTO™ X4 Technical data T e c h n ic a ld a ta General Accuracy with favourable conditions * Accuracy with unfavourable conditions ** Range with favourable conditions * Range with unfavourable conditions ** Smallest unit displayed X-Range Power Technology Laser class Laser type ø laser point | at distances Tilt measuring tolerance to laser beam **** Tilt measuring tolerance to housing **** Tilt measuring range **** Protection class Auto. laser switch off Auto. power switch off 1 mm / 0.04" *** 2 mm / 0.08" *** 0.05 - 150m / 0.16 - 500ft *** 0.05 - 80m / 0.16 - 260ft *** 0.1 mm / 1/32 in yes 635 nm, <1 mW 6 /30 /60 mm | 10/ 50/ 100 m ± 0.2° ± 0.2° 360° IP65 (dust- and splash water protected) after 90 s after 180 s Bluetooth® Smart Bluetooth® v4.0 Power of Bluetooth® Smart 0.71 mW Frequency of Bluetooth® Smart 2400 - 2483.5 MHz Range of Bluetooth® Smart <10m Battery durability (2 x AA) up to 4000 measurements Dimension (H x D x W) 132 x 56 x 29 mm | 5.2 x 2.2 x 1.1 in Weight (with batteries) 184 g/ 6.49 oz Temperature range Storage | Operation -25 to 70°C/ -13 to 158°F | -10 to 50°C/ 14 to 122°F * favourable conditions are: white and diffuse reflecting target (white painted wall), low background illumination and moderate temperatures. ** unfavourable conditions are: targets with lower or higher reflectivity or high background illumination or temperatures at the upper or lower end of the specified temperature range. *** Tolerances apply from 0.05 m to 10 m with a confidence level of 95%. With favourable conditions the tolerance may deteriorate by 0.10 mm/m for distances above 10 m. Leica DISTO™ X4 With unfavourable conditions the tolerance may deteriorate by 0.15 mm/m for distances above 10 m. **** after user calibration. Additional angle related deviation of +/-0.01° per degree up to +/-45° in each quadrant. Applies at room temperature. For the whole operating temperature range the maximum deviation increases by +/-0.1°. Technical data Functions Distance measuring Min/Max measuring Permanent measuring Stake out Addition/Subtraction Area Room angle Volume Painter function (area with partial measurem.) Pythagoras Smart Horizontal Mode / Indirect height Level Memory Beep Illuminated colour display yes yes yes yes yes yes yes yes yes 3-point yes yes yes yes yes Bluetooth® Smart yes Personalized Favorites yes Timer yes Point to point function/ distance yes ***** Smart Area yes ***** Height tracking yes ***** In combination with Leica DST 360 adapter Leica DISTO™ X4 Instrument Set-up In s tru me n tS e t-u p Introduction The safety instructions (see Safety Instructions) and the user manual should be read through carefully before the product is used for the first time. CAUTION Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor injury and/or appreciable material, financial and environmental damage. Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner. The person responsible for the product must ensure that all users understand these directions and adhere to them. The symbols used have the following meanings: WARNING Indicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury. Leica DISTO™ X4 Instrument Set-up Insert batteries To ensure a reliable use, we recommend using high quality Alkaline batteries. Change batteries when battery symbol is flashing. Switching ON/OFF Device is turned OFF. Leica DISTO™ X4 Instrument Set-up Clear Undo last action. Leave actual function, go to default operation mode. Message Codes If the message "i" appears with a number, observe the instructions in Message Codes section. Example: Leica DISTO™ X4 Instrument Set-up Multifunctional endpiece When measuring with 90° flipped-out endpiece please meake sure that it lies plane against the edge you measure from. The orientation of the endpiece is automatically detected and the zero point is adjusted accordingly. Adjusting measuring reference d) Distance is measured from a Leica DISTO Adapter FTA 360. a) Distance is measured from the rear of the device (standard setting). b) Distance is measured from the front of the device. c) Distance is measured from the tripod thread. Leica DISTO™ X4 Confirm setting. If device is switched off, reference goes back to standard setting (rear of the device). Settings Se tin g s Overview Tilt units Distance units Turning screen** Beep Bluetooth® Bluetooth® settings Illumination Favorites Keypad lock Tilt calibration Information / Serial number Offset Calibration of DST 360* Reset * Activated when connected to Leica DST 360 adapter ** Firmware update might be required through the Leica DISTO™ Plan App to get this feature Leica DISTO™ X4 10 Settings Tilt units Switch between the following units: 360.0° 0.00 % Confirm setting. Leica DISTO™ X4 Exit settings. 11 Settings Distance units Switch between the following units: 0.00 m 0.00 ft 0.000 m 0.000 in 0.0000 m 0'00" 1/32 0.0 mm 0 in 1/32 Confirm setting. Leica DISTO™ X4 Exit settings. 12 Settings Turning screen ON/OFF* * Firmware update might be required through the Leica DISTO™ Plan App to get this feature To switch ON, repeat procedure. Leica DISTO™ X4 Exit settings. 13 Settings Beep ON/OFF To switch ON, repeat procedure. Leica DISTO™ X4 Exit settings. 14 Settings Bluetooth® ON/OFF Bluetooth® is switched on and black Bluetooth® icon is displayed in status bar. If connection is established the color of the icon changes to blue. To switch ON, repeat procedure. Leica DISTO™ X4 Exit settings. 15 Settings Bluetooth® Settings If activated in measuring mode, it allows the arrow keys to move the cursor on your computer. Short press: send the value of the main line to your computer. Long press: send all measurements and results to your computer. Select ON or OFF. If device is connected, the favorites disappear and two softkeys appear: Confirm setting. Leica DISTO™ X4 Select kind of decimal point for transmitted value. Confirm setting. Select if unit is transmitted or not. 16 Settings Confirm setting. Select termination of transmission. Confirm setting. Exit settings. Leica DISTO™ X4 Confirm setting. Select if value is transmitted automatically or manually. 17 Settings Illumination Select brightness. Confirm setting. Exit settings. To save power reduce brightness if not necessary. Leica DISTO™ X4 18 Settings Personalized favorites Select favorite function. Press selection key left or right. Function is set as favorite above the corresponding selection key. Select your favorite functions for quick access. Short cut: Press 2 sec on a selection-key in the measuring mode. Select your favorite function and press again short on the corresponding selection key. Exit settings. Leica DISTO™ X4 19 Settings De-/Activate keylock To deactivate, repeat procedure. The keylock is active if device is switched off. Leica DISTO™ X4 Exit settings. 20 Settings Calibration of tilt sensor (Tilt Calibration) Place device on absolutely flat surface. Turn the device horizontally by 180° and place it again on absolutely flat surface. Leica DISTO™ X4 Place device on absolutely flat surface. 21 Settings Turn the device horizontally by 180° and place it again on absolutely flat surface. Leica DISTO™ X4 After 2 sec the device goes back to the basic mode. 22 Settings Information Exit information screen. Leica DISTO™ X4 Exit settings. 23 Settings Offset Select digit. Approve value. Adjust digit. Exit settings. An offset adds or subtracts a specified value automatically to or from all measurements. This function allows tolerances to be taken into account. The offset icon is displayed. Leica DISTO™ X4 24 Settings Calibration of Leica DST 360 adapter* * Function is activated when connected to the Leica DST 360 adapter. Define a point to be measured in a distance more than 8 m. Aim at defined point and press DIST button to start the 5 seconds countdown to measure. Turn the device vertically by 180°. Leica DISTO™ X4 Turn the device by 180°. Aim again at defined point and press DIST button to start the 5 seconds countdown to measure. Get more accurate results of the device in combination with the Leica DST 360 adapter. 25 Settings Reset Reset returns the instrument to the factory settings. All customized settings and memories are lost. Second confirmation with selection keys: a) Refuse b) Confirm Leica DISTO™ X4 26 Operations Op e ra tio n s Overview Single distance measurement Area Volume Room angle Smart Horizontal Mode Level Pythagoras (3-point) Stake out Timer Height tracking** Memory Point to point measurement* Point to point measurement levelled* Smart area measurement*/** * Activated when connected to Leica DST 360 adapter ** Firmware update might be required through the Leica DISTO™ Plan App to get this feature Leica DISTO™ X4 27 Operations Pointfinder This is a great help for outdoor measuring. The integrated pointfinder (viewscreen) shows the target on the display. The device measures in the middle of the cross hair, even if the laser dot is not visible. Parallax errors occur when the pointfinder camera is used on close targets, with the effect that the laser appears displaced in the crosshair. In this case rely on the real laser dot. When using the point to point functions and smart area measurement the error is automatically corrected Leica DISTO™ X4 with a shift of the crosshair. The pointfinder is always on, when the laser beam is on. 28 Operations Measuring single distance Aim active laser at target. Target surfaces: Measuring errors can occur when measuring to colourless liquids, glass, styrofoam or permeable surfaces or when aiming at high gloss surfaces. Against dark surfaces the measuring time increases. Leica DISTO™ X4 29 Operations Permanent / Minimum-Maximum measuring Use Down navigation key to take over values in the main line for sending via Bluetooth® Smart. Used to measure room diagonals (maximum values) or horizontal distance (minimum values). The minimum and maximum distance measured is displayed (min, max.). The last value measured is displayed in the main line. Stops permanent / minimum-maximum measuring. Leica DISTO™ X4 30 Operations Add / Subtract The next measurement is added to the previous one, respectively subtracted from the previous one. Leica DISTO™ X4 This process can be repeated as required. The same process can be used for adding or subtracting areas or volumes. 31 Operations Area The area is calculated based on the mathematic term multiplying 2 distances. Aim laser at first target point. Aim laser at second target point. Leica DISTO™ X4 a) First distance b) Second distance c) Circumference d) Area The result is shown in the main line and the measured value above. Painter function: Press + or - after starting the first measurement. Measure and add or subtract wall lengths. Measure finally height for second length to get the wall area. Use Down navigation key to take over values in the main line for sending via Bluetooth® Smart. 32 Operations Volume The volume is calculated based on the mathematic term multiplying 3 distances. Aim laser at first target point. Aim laser at second target point. Leica DISTO™ X4 Aim laser at third target point. 33 Operations Use Down navigation key to show more results or to take over values in the main line for sending via Bluetooth® Smart. a) First distance b) Second distance c) Third distance d) Volume Leica DISTO™ X4 a) Ceiling/floor area b) Wall areas c) Circumference 34 Operations Room angle The angle is calculated based on the cosine rule with 3 known side lengths of a triangle. Aim laser at first target point. Aim laser at second target point. Leica DISTO™ X4 Aim laser at third target point. 35 Operations Use Down navigation key to show more results or to take over values in the main line for sending via Bluetooth® Smart. a) First distance b) Second distance c) Third distance d) Angle between first and second measurement Leica DISTO™ X4 a) Circumference b) Triangular area 36 Operations Smart Horizontal Mode The horizontal distance is calculated based on the trigonimetric function cosine with 1 known length and 1 known angle. Aim laser at target (up to 360° and a transverse tilt of ±10°). Use Down navigation key to take over values in the main line for sending via Bluetooth® Smart. Leica DISTO™ X4 37 Operations Level Displays inclinations of 360°. Instrument beeps at 0° and 90°. Ideal for horizontal or vertical adjustments. Leica DISTO™ X4 38 Operations Pythagoras (3-point) The distance is calculated based on the Pythagorean theorem with 3 known lengths of 2 right-angled triangles. Aim laser at first target. Aim laser at second target. Leica DISTO™ X4 Aim laser at third target. 39 Operations The result is shown in the main line and the measured distance above. Pressing the measuring key for 2 sec in the function activates automatically Minimum or Maximum measurement. We recommend to use the pythagoras only for indirect horizontal measuring. For height measuring (vertical) it is more precise to use a function with inclination measurement. Use Down navigation key to take over values in the main line for sending via Bluetooth® Leica DISTO™ X4 Smart. 40 Operations Stake out Two different distances (a and b) can be entered to mark off defined measured lengths. Select digit. Leica DISTO™ X4 Adjust digit. Approve value "a". Adjust value "b". 41 Operations Approve value "b" and start measurement. Move device slowly along the stake out line. The distance to the next stake out point is displayed. a) Distance to first stake out point b) Actual position to measured target c) Distance to second stake out point The function can be stopped by pressing the CLEAR/OFF button. When approaching a stake out point to less than 18 mm the value of the stake out point is frozen and the arrows on the side change their colour to red for marking purposes. Leica DISTO™ X4 42 Operations Timer Select release time. Confirm setting. The self release starts if ON/Measure key is pressed. Leica DISTO™ X4 43 Operations Height tracking* * Firmware update might be required through the Leica DISTO™ Plan App to get this feature. Aim laser at lower point. The height is calculated based on trigonimetric functions with 1 known length and 1 measured angle. Aim laser at upper points and angle/height tracking starts automatically. Leica DISTO™ X4 Stops height tracking. 44 Operations Heights of buildings or trees without suitable reflective points can be determined. At the bottom point, distance and tilt is measured - which needs a reflective laser target. The upper point can be targeted with the pointfinder / crosshair and does not need a reflective laser target as only the inclination is measured. Use Down navigation key to show more results or to take over values in the main line for sending via Bluetooth® Smart. Leica DISTO™ X4 45 Operations Memory (last 20 results) a) Delete memory b) Take over value for further actions Leica DISTO™ X4 Use Down navigation key to show more detailed results of the specific measurement. Use Left/Right navigation keys to switch between measurements. 46 Operations Point to point measurement* * Function is activated when connected to the Leica DST 360 adapter. Aim laser at first target point. The tie distance is calculated based on 2 known coordinates with x,y and z value. Aim laser at second target point. Leica DISTO™ X4 Use Down navigation key to take over values in the main line for sending via Bluetooth® Smart. 47 Operations If chosen permanent measurement for second target point, the actual tie distance is displayed. Leica DISTO™ X4 48 Operations Point to point measurement levelled* * Function is activated when connected to the Leica DST 360 adapter. on 2 known coordinates with x,y and z value. For levelling, device needs to be in an inclination range of +/- 5°. Rotate the device clockwise 90°. Follow the instructions on the display. Use this Point to Point measurement function to get more measuring data. Do not move device after levelling. The tie distance is calculated based Rotate the device clockwise 90°. Follow the instructions on the display. Levelling is finished when OK icon appears on the display. Leica DISTO™ X4 Check status line: a) Indicates proper levelling b) Indicates insufficient levelling Aim laser at first target point. 49 Operations Aim laser at second target point. Use Down navigation key to take over values in the main line for sending via Bluetooth® Smart. If chosen permanent measurement for second target point, the actual tie distance is displayed. Leica DISTO™ X4 50 Operations Smart area measurement* * Function is activated when connected to the Leica DST 360 adapter. Firmware update might be required through the Leica DISTO™ Plan App to get this feature. Aim laser at first target point. The area is calculated based on several known coordinates with x,y and z value. Aim at and measure additional points (max. 30). Leica DISTO™ X4 a) Circumference of measured area Use Down navigation key to take over values in the main line for sending via Bluetooth® Smart. 51 Operations Bluetooth® Smart DISTO™ Plan. Use App for Bluetooth® data transfer. Your device can be also be updated through this App. Bluetooth® Smart is always active when the device is switched on. Connect the device with your smart-phone, tablet, laptop... Measurement values will be transferred automatically right after a measurement if "Autosend" is activated. To transfer a result press the following softkey: Leica DISTO™ X4 Bluetooth® switches off as soon as the laser distance meter is switched off. The efficient and innovative Bluetooth® Smart module (with the new Bluetooth® standard V4.0) works together with all Bluetooth® Smart Ready devices. All other Bluetooth® devices do not support the energy saving Bluetooth® Smart Module, which is integrated in the device. We provide no warranty for free DISTO™ software and offer no support for it. We accept no liability whatsoever arising from the use of the free software and we are not obliged to provide corrections nor to develop upgrades. A wide range of commercial software can be found on our homepage. Apps for Android® or iOS can be found in special internet shops. For more details, see our homepage. 52 Message Codes Me s s a g e Co d e s No. Cause Correction 156 Transverse tilt greater than 10° Hold the instrument without any transverse tilt. 162 Calibration error Make sure the device is placed on an absolutely horizontal and flat 204 Calculation error Perform measurement again. 240 Data transfer error Connect device and repeat procedure 252 Temperature too high Let device cool down. 253 Temperature too low Warm device up. 255 Received signal too weak, measuring time too long Change target surface (e.g. white paper). 256 Received signal too high Change target surface (e.g. white paper) . 257 Too much background light Shadow target area. 260 Laser beam interrupted Repeat measurement. 301 Device was moved, levelling not valid anymore Perform levelling again. Measuring with invalid levelling is partially 303 Error with Leica DST 360 adapter Repeat measurement. * If other message codes are displayed frequently even the instrument has been switched off and on, please contact your dealer. Leica DISTO™ X4 53 Care Ca re Clean the device with a damp, soft cloth. Never immerse the device in water. Never use aggressive cleaning agents or solvents. Leica DISTO™ X4 54 Warranty Wa ra n ty International Limited Warranty The Leica DISTO™ comes with a two year warranty from Leica Geosystems AG. To receive an additional year warranty, the product must be registered on our website at http://myworld.leicageosystems.com within eight weeks of the purchase date. If the product is not registered, our two year warranty applies. More detailed information about the International Limited Warranty can be found on the internet at: www.leica-geosystems.com/internationalwarranty. Leica DISTO™ X4 55 Safety instructions Sa fe ty in s tru c tio n s The person responsible for the instrument must ensure that all users understand these directions and adhere to them. The product is permitted to use for skilled persons only. Symbols used The symbols used have the following meanings: Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner. WARNING Indicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury. CAUTION Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor injury and/or appreciable material, financial and environmental damage. Leica DISTO™ X4 56 Safety instructions Permitted use Prohibited use Measuring distances Using the product without instruction Tilt measurement Using outside the stated limits Data transfer with Bluetooth® Leica DISTO™ X4 Deactivation of safety systems and removal of explanatory and hazard labels Opening of the equipment by using tools (screwdrivers, etc.) Use of accessories from other manufacturers without express approval Carrying out modification or conversion of the product Deliberate dazzling of third parties; also in the dark Inadequate safeguards at the surveying site (e.g. when measuring on roads, construction sites, etc.) Hazards in use WARNING Watch out for erroneous measurements if the instrument is defective or if it has been dropped or has been misused or modified. Carry out periodic test measurements. Particularly after the instrument has been subject to abnormal use, and before, during and after important measurements. CAUTION Never attempt to repair the product yourself. In case of damage, contact a local dealer. WARNING Deliberate or irresponsible behaviour on scaffolding, when using ladders, when measuring near machines which are running or near parts of machines or installations which are unprotected Changes or modifications not expressly approved could void the user´s authority to operate the equipment. Aiming directly in the sun Only use chargers recommended by the manufacturer to charge the batteries. CAUTION 57 Safety instructions Limits of use Refer to section Technical data. The device is designed for use in areas permanently habitable by humans. Do not use the product in explosion hazardous areas or in aggressive environments. Areas of responsibility Responsibilities of the manufacturer of the original equipment: Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Internet: www.leica-geosystems.com The company above is responsible for supplying the product, including the User Manual in a completely safe condition. The company above is not responsible for third party accessories. Responsibilities of the person in charge of the instrument: Leica DISTO™ X4 To understand the safety instructions on the product and the instructions in the User Manual. Disposal CAUTION Flat batteries must not be disposed of with household waste. Care for the environment and take them to the collection points provided in accordance with national or local regulations. The product must not be disposed with household waste. Dispose of the product appropriately in accordance with the national regulations in force in your country. Adhere to the national and country specific regulations. Product specific treatment and waste management can be downloaded from our homepage. To be familiar with local safety regulations relating to accident prevention. Always prevent access to the product by unauthorised personnel. 58 Safety instructions Electromagnetic Compatibility FCC statement (applicable in U.S.) (EMC) This equipment has been tested and found to comply with the limits for a Class B digital instrument, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. WARNING The device conforms to the most stringent requirements of the relevant standards and regulations. However, the possibility of causing interference in other devices cannot be totally excluded. this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement The radiated rf output power of the instrument is below the FCC radio frequency exposure limits for portable devices according to KDB 447498. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules. Operation is subjected to the following two conditions: Leica DISTO™ X4 This device may not cause harmful interference, and 59 Safety instructions ISED Statement (applicable in Japanese Radio Law Compliance Canada) This device is granted pursuant to the Japanese Radio Law 電 波 法 . This device should not be modified otherwise the granted designation number will become invalid. This device complies with Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: This device may not cause harmful interference, and this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Compliance Statement The radiated rf output power of the instrument is below the Health Canada's Safety Code 6 exclusion limit for portable devices (radiated element separation distance between the radiating element and user and/or bystander is below 20 cm). Use of the product with Bluetooth® WARNING Electromagnetic radiation can cause disturbances in other equipment, in installations (e.g. medical ones such as pacemakers or hearing aids) and in aircraft. It can also affect humans and animals. Precautions: Although this product conforms to the most stringent standards and regulations, the possibility of harm to people and animals cannot be totally excluded. Leica DISTO™ X4 Do not use the product near petrol stations, chemical plants, in areas with a potentially explosive atmosphere and where blasting takes place. Do not use the product near medical equipment. Do not use the product in airplanes. Do not use the product near your body for extended periods. 60 Safety instructions Laser classification The device produces visible laser beams, which are emitted from the instrument: It is a Class 2 laser product in accordance with: IEC60825-1 : 2014 „Radiation safety of laser products“ Wavelength 620 - 690 nm Maximum radiant output power for classification < 1 mW Pulse duration > 400 ps Pulse repetition frequency Laser Class 2 products: Do not stare into the laser beam or direct it towards other people unnecessarily. Eye protection is normally afforded by aversion responses including the blink reflex. 320 MHz Beam divergence 0.16 x 0.6 mrad WARNING Looking directly into the beam with optical aids (e.g. binoculars, telescopes) can be hazardous. CAUTION Looking into the laser beam may be hazardous to the eyes. Don't dazzle other individuals. Pay particular attention to the direction of the laser beam when remotely operating the product via an app or software. A measurement could be triggered at any time. Leica DISTO™ X4 61 Safety instructions Labelling Subject to change (drawings, descriptions and technical data) without prior notice. Leica DISTO™ X4 62
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Page Mode : UseOutlines Has XFA : No Page Count : 63 Language : en-gb XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : kla Description : Title : My Document Create Date : 2018:01:17 15:36:24+01:00 Modify Date : 2018:02:22 11:27:17+01:00 Metadata Date : 2018:01:17 15:41:38+01:00 Keywords : Producer : madbuild Document ID : uuid:92a95e32-904d-46b8-85ab-fab63dd527df Instance ID : uuid:ca29f9dd-2f92-4f2c-a1c2-d0a9ea977bc7 Author : kla Subject :EXIF Metadata provided by EXIF.tools