Leica Geosystems CPD MTD0506 Handheld Laser Distance Meter User Manual 02 gb UM DistoA6
Leica Geosystems AG, CPD Handheld Laser Distance Meter 02 gb UM DistoA6
Contents
- 1. user manual
- 2. safety instructions
user manual
User Manual Version 1.0 Inserting / replacing Batteries English See figure {C} - Open the positioning bracket. Remove the locking clip and slide the endpiece down. Slide the red locking mechanism to the side and open the battery compartment. Insert new or replace used batteries. Close battery cover, reinsert the endpiece and fix locking clip. The battery symbol {B, 21} appears permanently blinking in the display when the battery voltage is too low. The batteries should be replaced as soon as possible. • Pay attention to correct polarity. • Use alkaline batteries. • Batteries should be removed if the device will not be used for a long time (danger of corrosion). When changing the batteries the settings and stack content remain unchanged. Congratulations on your purchase of a Leica DISTO™. The safety instructions can be found in a separate booklet, which accompanies this user manual. The safety instructions along with the user manual should be read carefully before initial operation. Helpful Hint: The first and last page including the pictures should be folded out and left open, whilst reading through the manual. Letters and Numbers in braces {} refer to the illustrations. Content Start-up ................................................................ 1 Menu functions ................................................... 3 Operation............................................................. 4 Measuring ............................................................ 4 Functions ............................................................. 5 Working with BLUETOOTH® .............................. 8 Appendix .............................................................. 9 Leica DISTO™ A6 1.0.0 gb Start-up GB NL DK FIN CN Multifunctional Endpiece See figure {D} The device can be used for different measurement situations: • For measurements from an edge open the positioning bracket until it locks in place. See figure {E}. • For measurements from a corner, open the positioning bracket until it locks in place, with a slight Start-up RC ROK PL RUS CZ D GB NL DK FIN push to the right the bracket can be turned further. See figure {D and F}. A built-in sensor automatically detects the orientation of the positioning bracket and calculates the corresponding distances accordingly. Integrated telescopic viewfinder The integrated bubble level allows simple horizontal levelling of the instrument. RC See figure {A}: 1 ON/MEASURING 2 2nd FUNCTION LEVEL 3 PLUS [+] 4 TIMER 5 EQUAL [=] 6 AREA/VOLUME 7 STORAGE 8 MEASUREMENT REFERENCE PL RUS See figure {B} 1 Information about faulty measurements 2 Laser active 3 Circumference 4 Maximum value of continuous measurement 5 Minimum value of continuous measurement 6 Measurement reference 7 Recall of Historical Storage 8 Storage of constant 9 Main line 10 Units with exponents (2/3) 11 Ceiling area 12 Wall area 13 Three auxiliary lines (e.g. previous results) 14 BLUETOOTH® on/off 15 2nd Function Level on 16 Hardware error 17 Indirect measurement - Pythagoras 18 Indirect measurement - Pythagoras - partial height 19 Area / Volume 20 Offset setting 21 Battery indication Level Keypad CLEAR/OFF MENU ILLUMINATION INDIRECT MEASUREMENT (PYTHAGORAS) MINUS [-] BLUETOOTH® Display The device is equipped with a telescopic viewfinder on the right hand side. The viewfinder is especially helpful when aiming at distant targets. When looking through the viewfinder, the target is clearly visible thanks to the 2x magnification. At distances beyond 30 m laser spot is centered on the crosshair, below 30 m the laser spot appears on the edge of the crosshair, which is normal. CN ROK 10 11 12 13 14 CZ Start-up Leica DISTO™ A6 1.0.0 gb Distance 0' 0'' 1/32 0.0 in 0 1/32 in Menu functions Presettings The menu allows selection of the settings that will remain in memory after the instrument is switched off. Area 0.00 ft² 0.00 ft² 0.00 ft² Volume 0.00 ft³ 0.00 ft³ 0.00 ft³ An offset automatically adds or subtracts a value to/ from ALL measurements. With this feature tolerances can be taken into consideration e.g. between unfinished and finished dimensions. Press the MENU -key {A, 10} repeatedly to scroll through the possible menu functions (UNIT, OFFSET, TRIPOD, RESET). Selecting Units Select the menu function OFFSET {B, 20} (OFFSET blinks in the display), confirm with the EQUAL - key {A, 5}. Adjust the OFFSET with the PLUS - key {A, 3} or the MINUS - key {A, 13}. By holding the keys down, the setting values will increase/decrease faster. Once you have entered the proper offset confirm your selection with the EQUAL - key {A, 5}. As long as an OFFSET {B, 20} is added/ subtracted the symbol is visible on the display. "UNIT" blinks in the display. Possible units: Measuring with tripod When the desired menu option appears, select it with the EQUAL - key {A, 5}, scroll through the possible settings with the PLUS - key {A, 3} or the MINUS key {A, 13} and store the selected setting with the EQUAL - key {A, 5}. Press CLEAR - key {A, 9} to leave the menu without saving any changes in the settings. Distance 0.000 m 0.00 m 0 mm 0.00 ft 0.00 1/32 ft in Area 0.000 m² 0.00 m² 0.000 m² 0.00 ft² 0.00 ft² Leica DISTO™ A6 1.0.0 gb NL DK FIN CN RC Using a tripod eliminates shaking when measuring over long distances. On the back of the instrument is an industry standard ¼"-threaded hole for use with a camera tripod mounting screw. For correct measurements the reference needs to be adapted. Select the menu function TRIPOD {A, 8} ("triPod" blinks in the display) and confirm with the EQUAL - key {A, 5}. Volume 0.000 m³ 0.00 m³ 0.000 m³ 0.00 ft³ 0.00 ft³ GB Measure with offset Navigation in the Menu ROK PL RUS CZ Menu functions D GB NL DK FIN CN RC ROK Reset Measuring reference When you select the menu function RESET ("rESET" will blink in the display) and press the EQUAL-key {A, 5} twice the device will default to factory settings. CAUTION: Any customized presettings as well as stored values will be deleted. If the positioning bracket is folded out, the device recognizes the position, adapts the reference and calculates distances accordingly. The default reference setting is from the rear of the instrument. By pressing the REFERENCE - key {A, 8}, the setting can be changed, so that the next measurement taken will be from the "front" of the in-strument. Afterwards the reference setting automatically defaults back to rear. See picture {G}. You can choose the "front" reference permanently by pressing the REFERENCE - key {A, 8} longer. Press the REFERENCE - key {A, 8} longer another time to change back to the "rear" reference. See also "Measuring with tripod". Operation Switching On/Off ON: OFF: Press ON - key {A, 1} briefly. Battery indication is displayed until the next keystroke. Press and hold OFF - key {A, 9}. To maximize battery life the laser beam will switch off after 3 minutes of inactivity, the device will automatically switch off after 6 minutes of inactivity. Measuring Single distance measuring Pressing DIST - key {A, 1} turns the laser on. Aim at the desired target and press DIST - key {A, 1} again. The measured distance is displayed immediately in the chosen unit. CLEAR key Pushing the CLEAR - key {A, 9} clears the last entry or measurement. Within a function (area, volume, etc.) single measurements can be deleted step by step and remeasured. Minimum/maximum measuring PL RUS This function allows the user to measure the minimum or maximum distance from a fixed measuring point as well as to determine spacing - see figure {H}. It is commonly used to measure diagonal distances Illumination Pressing the ILLUMINATION - key {A, 11} turns on/ off the display backlight. CZ Operation Leica DISTO™ A6 1.0.0 gb area function. The corresponding symbol appears in the display. When both measurements have been taken the result will be automatically calculated and displayed in the main line. Press the AREA/VOLUME - key {A, 6} longer to calculate the circumference {B, 3}. Press the AREA/ VOLUME - key {A, 6} longer again to return to the previous area measurement. If you want to measure another area, press AREA/ VOLUME - key {A, 6} again. (maximum values) or horizontal distances (minimum values). Press and hold DIST - key {A, 1} until you hear a beep, indicating the device is in a continuous measuring mode. Then slowly sweep the laser back and forth respectively up and down over the desired target point - see figure {I, J} - (e.g. a corner in the room). Press DIST - key {A, 1} again and the continuous measurement will be stopped. The values for maximum and minimum distances are shown in the display as well as the last measured value in the main line. Special Function: Sides to be measured can be made up of several distances. If necessary, all sides of your area measurement can be made up of several partial measurements. Choose the area mode. Press the PLUS - key {A, 3} or MINUS - key {A, 13} before you start with the first partial measurement. Proceed with the first partial measurement by pressing DIST - key {A, 1}. In the display an addition or subtraction symbol appears. Make the first partial measurement, press PLUS - key {A, 3} or MINUS - key {A, 13} and make the second partial measurement. Unlimited partial measurements can be summed up or subtracted. To finish the distance measurement press the EQUAL - key { A, 5}. The second distance can be made up of partial distances with the same method. The area result is shown as usual in the main line. Functions Addition/Subtraction To add or subtract two or more measurements simply works as follows: Measurement +/- Measurement +/- Measurement +/- …. = RESULT Pressing the EQUAL - key {A, 5} ends the sequence and displays the result in the main line; the actual measurements are scrolled upwards in the display. Pushing the CLEAR - key {A, 9} undoes the most recent operation. Areas and volumes can be added/subtracted in exactly the same manner. GB NL DK FIN CN RC ROK PL RUS Area Press the AREA/VOLUME - key {A, 6} once for the Leica DISTO™ A6 1.0.0 gb CZ Functions D GB NL DK FIN CN RC ROK PL RUS partial distances with the same method. The volume result is shown as usual in the main line. Volume Press the AREA/VOLUME - key {A, 6} twice for the volume function. The corresponding symbol appears in the display. When 3 measurements have been taken the result will be automatically calculated and displayed in the main line. Press the AREA/VOLUME - key {A, 6} longer to display additional room information such as ceiling/ floor area, surface area of the walls, circumference. Press the AREA/VOLUME - key {A, 6} long again to return to the previous volume measurement. If you want to measure another volume press AREA/ VOLUME - key {A, 6} again. Indirect Measuring The device can calculate distances using Pythagoras' theorem. This method is useful when the distance to be measured is difficult or dangerous to access. • The method is only used to estimate distances, it cannot replace an accurate measurement. • Make sure you strictly follow the sequence of the measurements • All target points need to be vertically or horizontally in the same plane • Best results can be expected if the device is turned around a fixed point (e.g. positioning bracket folded out completely and the device is held towards a wall) • It is highly recommended to use the "Minimum/ maximum measuring" by pressing the DIST key {A, 1} longer. The minimum value is used for the measurements perpendicular towards the target respectively the maximum value for the other measurements. This increases the accuracy of the indirect measuring considerably. Special Function: Sides to be measured can be made up of several distances. If necessary, all sides of your volume measurement can be made up of several partial measurements. Choose the volume mode. Press the PLUS - key {A, 3} or MINUS - key {A, 13} before you start with the first partial measurement. Proceed with the first partial measurement by pressing DIST - key {A, 1}. In the display an addition or subtraction symbol appears. Make the first partial measurement, press PLUS - key {A, 3} or MINUS - key {A, 13} and make the second partial measurement. Unlimited partial measurements can be summed up or subtracted. To finish the distance measurement press the EQUAL - key { A, 5}. The second and the third distance can be made up of Indirect Measuring - Determination with two points See figure {K} Press the PYTHAGORAS - key {A, 12} until the correct symbol appears on the display. The distance CZ Functions Leica DISTO™ A6 1.0.0 gb to be measured will flash in the display. Take the necessary measurements. The result and the single measurements appear on the display. CAUTION: Right angle is necessary between the second measurement and the resulting distance. We recommend to press the DIST - key {A, 1} longer to activate the perpendicular (min.) measuring function. the perpendicular (min.) measuring function. Storage of Constants/Historical Storage Storage of a Constant See figure {L} Press the PYTHAGORAS - key {A, 12} until the correct symbol appears on the display. The length to be measured appears flashing on the display. Take the necessary measurements. The result and the single measurements appear on the display. CAUTION: Right angle is necessary between the second measurement and the resulting distance. We recommend to press the DIST - key {A, 1} longer to activate the perpendicular (min.) measuring function. Press STORAGE - key {A, 7} to recall the constant and make it available with a press on the EQUAL - key {A, 5} for further calculations. Special function: Adjusting the constant A measured value can be adjusted. If you press the EQUAL - key {A, 5}, the value starts blinking and can be adjusted with the PLUS - key {A, 3} or MINUS key {A, 13}. Through pressing the EQUAL - key {A, 5} again the adjustment is confirmed. Now the value can be stored as usual as a constant. See figure {M} Press the PYTHAGORAS - key {A, 12} until the correct symbol appears on the display. The length to be measured appears flashing on the display. Take the necessary measurements. The result and the single measurements appear on the display. CAUTION: Right angle is necessary between the third measurement and the resulting distance. We recommend to press the DIST - key {A, 1} longer to activate Leica DISTO™ A6 1.0.0 gb Historical Storage Press STORAGE - key {A, 7} twice quickly and the previous 20 results (measurements or calculated results) are shown in reverse order. Using the PLUS key {A, 3} and the MINUS - key {A, 13} allows to navigate in the historical storage. Press EQUAL - key {A, 5} to take a result from the historical storage to use for further calculations. NL Recalling the constant Indirect Measuring - Determination of a partial height with three points GB It is possible to store and recall a frequently used value e.g. height of a room. Measure the desired distance, press and hold STORAGE - key {A, 7} until the device beeps to confirm the storage. Indirect Measuring - Determination with three points Functions DK FIN CN RC ROK PL RUS CZ D GB NL DK FIN Timer The direction keys Press and hold TIMER - key {A, 4} until desired time delay has been reached (5 - 60 seconds). Press DIST - key {A, 1}. Once the key is released the remaining seconds until measurement are displayed. The last 5 seconds are counted down with a beep. After the last beep the measurement is taken. Eight direction keys (identified by a small arrow near the key) on the operator's keypad are used to manoeuvre the cursor. The direction keys become active when you switch to the second level (by pressing the 2nd key {A, 2}). The distance measuring key is active in both levels. The functionality of the direction keys depends on the software used. Special function: Switch off of Beep Pressing MENU - key {A, 10} and MINUS - key {A, 13} together for 4 sec. switches the Beep off or on. Switching on BLUETOOTH® / sending measurements PL Switching off BLUETOOTH® CN RC ROK RUS If your software supports the direction keys use them to select the appropriate position for the cursor. To transmit the measurement press the BLUETOOTH® key {A, 14}. The measurement is then transmitted to your Pocket PC. For further details please consult your manual for the software used. Working with BLUETOOTH® A quick press on the BLUETOOTH® - key {A, 14} starts DISTO BLUETOOTH®. The data connection must then be established out from Pocket PC / PC by the application software. The BLUETOOTH® - icon in the display {B, 14} will continue to blink until this has been successfully completed. BLUETOOTH® automatically switches off if the connection to the Pocket PC / PC is not established within 120 sec from when the BLUETOOTH® was switched on. Transmitting the measurement During data transmission If the data is not confirmed as being successfully received by the Pocket PC / PC then no new measurement can be processed. The Info code "240" appears in the display if no data transmission has taken place after 2 seconds. Press the CLEAR - key {A, 9} and repeat the measurement and then transmit it. Selecting particular values in the display BLUETOOTH® switches off as soon as the DISTO™ is switched off. By using the Min. / Max. function particular measurements can be selected for transmission. The display shows a number of measurements (min., max., last CZ Working with BLUETOOTH® Leica DISTO™ A6 1.0.0 gb measurement taken). You can select a particular measurement by using a longer press on the PLUS key {A, 3} or a longer press on the MINUS - key {A, 13}. When selected the measurement blinks. Once selected and blinking, the measurement can be transmitted using the BLUETOOTH® - key {A, 14}. The same selection process can be used for areas, volumes, indirect measurements and room dimensions. GB Message Codes All message codes will be displayed with either "InFo" or "Error". The following mistakes can be corrected: InFo 204 206 Transmission of user-entered measurements A measurement on the display can be changed if you wish. By pressing the EQUAL - key {A, 5} the value blinks and can then be changed using the PLUS - key {A, 3} and the MINUS - key {A, 13}. Pressing the keys for longer increases the rate of change. Pressing the EQUAL - key {A, 5} again confirms the change and the value can be transmitted as normal. 240 245 252 NOTE The free software supplied is designed to provide the user with basic functionality. Leica Geosystems provides no warranty for this free software and offers no support for it. Leica Geosystems accepts no liability whatsoever arising from the use of the free software and is not obliged to provide corrections nor to develop updates or upgrades. 253 255 256 257 You can find numerous commercial vendors of software for a wide range of applications on our homepage. Leica DISTO™ A6 1.0.0 gb Appendix 260 Cause Remedy Calculation error Repeat procedure No endpiece detec- Attach the endpiece tion properly. If error still occurs, replace the endpiece. Error in data trans- Repeat process mission Establish BLUE2nd key pressed although no BLUE- TOOTH® connection ® TOOTH connection exists. Temperature too Cool down instrument high Temperatur too low Warm up instrument Receiver signal too Use target plate weak, measurement time too long, distance > 100 m Received signal too Use target plate powerful (grey side) Wrong measureUse target plate ment, ambient (brown side) brightness too high Laser beam interRepeat measurement rupted Appendix NL DK FIN CN RC ROK PL RUS CZ D Error GB Cause Hardware error NL DK FIN CN RC ROK PL RUS Integrated level Multifunctional endpiece Timer Single Measurement Maximum, Minimum, Continuous Measurement Historical storage of Indirect Measuring functions with Pythagoras Storage of constant Area/Volume calculation with room calculations Addition/Subtraction Tripod thread Battery life, Type AA, 2 x 1.5V IP rating Remedy Switch on/off the device several times and check if the symbol still appears. If so please call your dealer for assistance. Technical Data Range 0.05 m to 200 m 0.2 ft to 650 ft Power Range Measurements can be Technology™ made up to 100 m without target plate Measuring accuracy up typ.: ± 2 mm* to 30 m (2 σ, standard deviation) Smallest unit displayed 1 mm Laser class II Laser type 635 nm, < 1 mW Ø laser spot (at 6 / 30 / 60 mm distance) (10 / 50 / 100 m) Autom. switch off laser 3 min Autom. switch off instrument 6 min Integrated telescopic viewer 2x magnification BLUETOOTH® Range of BLUETOOTH® Cl. 2 min. 10 m Display illumination Dimension Weight (with batteries) Temperature range: Storage Operating 20 values up to 10 000 measurements IP 54 splash proof, dust proof 148 x 64 x 36 mm 270 g -25°C to +70°C (-13°F to +158°F) -10°C to +50°C (-14°F to +122°F) * maximum deviation occurs under unfavourable conditions such as bright sunlight or when measuring to poorly reflecting or very rough surfaces. For distances over 30 m the maximum deviation may increase to a maximum of ± 10 mm. CZ Appendix 10 Leica DISTO™ A6 1.0.0 gb The Leica DISTO™ A6 is a product belonging to Radio Equipment Class 1 (radiated power < 10 mW; operating at a frequency range of 2400 to 2483 MHz) in accordance with the R&TTE Directive and in a harmonised frequency band. As it is a product belonging to Radio Equipment Class 1 its use within EU countries is not subject to any limitations. Care Do not immerse the unit in water. Wipe off dirt with a damp, soft cloth. Do not use aggressive cleaning agents or solutions. Treat the optical surfaces with the same care that you would apply to eyeglasses and cameras. Measuring Range At night, at dusk and when the target is shadowed the measuring range without target plate is increased. Use a target plate to increase the measurement range during daylight or if the target has a bad reflection. Warranty Measuring Conditions GB The Leica DISTO™ A6 comes with a two (2) year warranty from Leica Geosystems AG. More detailed information can be found at: www.disto.com All illustrations, descriptions and technical specifications are subject to change without prior notice. NL DK FIN Measuring Surfaces Measuring errors can occur when measuring toward colourless liquids (e.g. water) or dust free glass, styrofoam or similar semi-permeable surfaces. Aiming at high gloss surfaces deflects the laser beam and measurement errors can occur. Against non-reflective and dark surfaces the measuring time can be increased. CN RC ROK PL RUS CZ Leica DISTO™ A6 1.0.0 gb 11 Appendix D GB NL DK FIN CN RC ROK PL RUS CZ Appendix 12 Leica DISTO™ A6 1.0.0 gb
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Page Mode : UseNone XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Create Date : 2002:04:25 16:13:33Z Creator Tool : FrameMaker 7.2 Modify Date : 2006:05:22 07:59:15+01:00 Metadata Date : 2006:05:22 07:59:15+01:00 Format : application/pdf Title : 02-gb_UM_DistoA6.fm Creator : rog Document ID : uuid:bd1ccde6-96d9-4808-881e-d4f4705f9447 Instance ID : uuid:00c1922c-df22-4649-9e80-9380ddba9263 Page Count : 12 Author : rogEXIF Metadata provided by EXIF.tools