Leidos NORMARC7011 NORMARC 7011 User Manual Installation and Commissioning Handbook Vol 1

Lockheed Martin Air Traffic Management NORMARC 7011 Installation and Commissioning Handbook Vol 1

7011 Installation and Communications Manual Vol 1

© 1999 Navia Aviation AS 21465-3.0NORMARC 7000INSTRUMENT LANDING SYSTEMInstallation & Commissioning Handbook Vol. 1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.RECORD OF CHANGESNM 7000 seriesPart no.:21465Change No.: Section: Entered by: Rev.:Section 1 3.0.Section 2 3.0.Section 3 3.0.Section 4 3.0.Section 5 3.0.Section 6 3.0.Change No.: Description:

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.TABLE OF CONTENTSInstallation and Commissioning Handbook Vol. 1NM 7000 SeriesFor further information, please look up Installation & Commissioning Handbook Volume 2, containing drawings and parts lists.SECTION 1 ANTENNA INSTALLATION PROCEDURESSECTION 2 SHELTER INSTALLATIONSECTION 3 ANTENNA SYSTEMS ADJUSTMENTS PROCEDURESChapter 1 NM 3522 6-element ArrayChapter 2 NM 3523B 12-element Single Frequency ArrayChapter 3 NM 3524 12-element Dual Frequency ArrayChapter 4 NM 3525 24-element ArrayChapter 5 NM 3526 16-element ArrayChapter 6 NM 3543 Null-Reference Glide PathChapter 7 NM 3544 Sideband-Reference Glide PathChapter 8 NM 3545 M-array Glide PathChapter 9 NM 3561 Marker Beacon SystemChapter 10 NM 3562 Dual Antenna Marker BeaconSECTION 4 EQUIPMENT TEST AND ADJUSTMENTSSECTION 5 APPENDIXChapter 1 Ground commissioning document LocalizerChapter 2 Ground commissioning document Glide PathChapter 3 Ground commissioning document Marker BeaconChapter 4 Ground commissioning document Far Field MonitorSECTION 6 APPENDIXDiagramsInstructions for coax connectors

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.SECTION 1ANTENNA INSTALLATION PROCEDURETable of contents1 Civil Work Checks ....................................................................................................31.1 Unpacking ..........................................................................................................32 Localizer Antenna System Assembly.....................................................................52.1 Positioning of antenna frame work..................................................................... 52.2 Framework assembly ......................................................................................... 52.3 Cable duct assembly.......................................................................................... 62.4 Antenna assembly.............................................................................................. 62.5 Anntenna cables................................................................................................. 62.6 Near Field monitor antenna installation..............................................................92.7 Cable installation NF .......................................................................................... 93 Glidepath antenna system assembly/towers 10m and 15m .................................113.1 General............................................................................................................... 113.2 Bottom Section...................................................................................................123.2.1 Vertical Beams.............................................................................................123.2.2 Bottom Flange ............................................................................................. 123.2.3 Diagonal struts.............................................................................................133.2.4 Third vertical leg .......................................................................................... 133.2.5 Ladder.......................................................................................................... 133.2.6 Locking of nuts............................................................................................. 133.3 Middle section .................................................................................................... 133.3.1 Vertical legs ................................................................................................. 133.4 Top section......................................................................................................... 133.4.1 General........................................................................................................ 133.4.2 Horizontal struts...........................................................................................133.5 Obstruction light ................................................................................................. 133.5.1 Obstruction light bracket ..............................................................................133.5.2 Obstruction light...........................................................................................143.6 Antenna suport...................................................................................................143.6.1 Adjustment rails ........................................................................................... 143.6.2 Mounting of supports ...................................................................................143.6.3 Antenna assembly .......................................................................................143.7 Cable trunks ....................................................................................................... 143.7.1 Cable trunk brackets.................................................................................... 143.7.2 Antenna cables............................................................................................153.8 Antenna mast erection .......................................................................................153.8.1 Erection of the mast..................................................................................... 153.8.2 Locking of nuts............................................................................................. 153.9 Cable installation into shelter ............................................................................. 153.9.1 Cable tube ................................................................................................... 153.9.2 Cable installation ......................................................................................... 154 Near field monitor..................................................................................................... 174.1 Cable installation................................................................................................174.2 NF Monitor antenna assembly ...........................................................................17

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$65 Marker beacon installation antenna assembly......................................................195.1 Antenna assembly.............................................................................................. 195.2 Antenna Cables installation................................................................................195.3 Antenna Mast erection .......................................................................................19

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.1 Civil Work ChecksCheck that the civil work is carried out according to NM specifications.• Correct positions for antenna foundation bolts.• Correct dimensions and quality of bolts in concrete.• Check note 4 and 5 on LLZ foundation drawing.• Earth sticks/plates at shelter and antenna foundation.• Shelter interior installations.• Mains power installations in shelter and antenna assembly.• Pulling rope in cable ducts.• Remote control cables and terminals for RCU interface.1.1 UnpackingEquipment cases are carefully transported to the appropriate sites before unpacking.Check each item toward packing list so as to detect any discrepancy before assemblies.Parts to be installed in shelters shall be immediately brought inside.Do not spread out loose isopore pieces

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.2 Localizer Antenna System Assembly2.1 Positioning of antenna frame workBy means of a theodolite determine the exact position of the extended runway centre line and mark the 90 degrees angle points on each concrete slab. See Figure 2-1.Figure 2-1 Alignment of antenna frame work.2.2 Framework assemblySee Vol. 2 Section 2 Chapter 6.See also Figure 2-1On middle aluminium bar mark exact centre. Position the bar accurately so the marks line up with the extended centre line. Affix the two clamping angles.The remaining aluminium bars of the front part can now be assembled across the concrete fundaments. Use junction plates between each bar. On each fundament (left and right) adjust to the same distance between the theodolite mark and the aluminium bar.The al. Bars are numbered at each end on top side. The center bar is marked 1-1 and the next bar on each side is marked 1-2. The third bar on each side is marked 2-3 and so on.Figure 2-2 22 11 11 22 3

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6Check antenna spacing after assembly. Repeat for the rear bars and maintain correct spac-ing distance between the front and rear bars.Tighten all clamping angles.2.3 Cable duct assemblySee Vol. 2 Section 2 Chapter 6.The cable duct sections are numbered and should be assembled according to the drawing. Sections are joined together by means of blind rivets. When the assembly is complete drill holes through to the concrete and fix the duct by means of plastic plugs and screws.The lids should not be put on until cables are installed.2.4 Antenna assemblySee Vol. 2 Section 2 Chapter 6.Lay out all masts and stay on the frame work.Place the bottom ends on al.bar and let all top ends point towards the runway. Notice that the rear masts have a slot near the bottom end.Before erecting, all monitor and antenna cables must be installed. Check that the cable mark-ings are close to the connector. Roll off about one meter from the outer end and form it to a straight line. Push the cable through the slot in the mast all the way to the top at the same time as you roll off more of the cable. Gently turn the roll left/right to avoid the obstacles inside the mast. Leave the rest of the roll in the cable duct.After all cables are installed the masts can be erected. Secure masts with stays immediately after erection. Depending on antenna mast height there will be one or two long stays between front and rear rows.Tighten all bolts at the mast bottom. Level the masts sideways and tighten the short stays. Leave the long stays loose, to make it easier to install antennas. Install the networks. Check the drawing for antenna system in question. Don’t forget the thick alu.-washer behind the backplate ( pos 9 dwg 16361 A3 ) Install the antennas. The flange at the front can be tightened with all four bolts. Cables should not be connected at this stage, just secure the rear flange with one bolt. 2.5 Anntenna cablesDuring this operation the connectors must be protected.Carefully roll out the cables forward, through the antenna system and towards the runway. All cables to the left of the centre should be brought to the left of respectively mast and of course opposite for the other side (see figure 2-3 )Cut appr. 0,5 m pieces of the flexible conduit, one for each antenna. Push them over the cables and into the mast, leaving just a few cm outside. Also slide the plastic bushing all the way to the mast. Pull the cables back and feed them through the hole in the cable duct. Lay the cables in a loop inside the duct, and connect them to respectively network. Be observant by pulling so the cables don’t hook on to any obstacles on the ground.

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.Now the cables can be connected to the antennas. Lift up the rear end 4-5 cm and put some-thing between the flanges to keep them apart. Be careful don’t shake the mast. Connect the cables, take away the support and tighten the flange.Level the antenna masts backward/forward and tighten the long supports.

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6Figure 2-3

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.2.6 Near Field monitor antenna installationThe mast shall be assembled and installed at the extended runway centre line according to dwg.no. 14256A3 Vol. 2 Section 2 Chapter 8.The NF antenna shall be installed horizontally and point towards the centre of the LLZ antenna array.2.7 Cable installation NFThe NF Monitor cable is first carefully rolled out and positioned such that there is no risk for damage during installation in the cable duct.The cable is fixed to the pulling rope at the NF position end together with and extra rope for maintenance purpose.Connectors and cable labels must be protected against dust and water wear during pulling operation.The cable is pulled through the pipe into the shelter and installed and connected to the NF Monitor Input of the Cabinet.The coaxial cable shall be protected with flexible conduit tube and strapped along the mast. The entrance of the cable tube shall be filled with expansion foam in order to prevent water leakage into the cable tube.

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.3 Glidepath antenna system assembly/towers 10m and 15m3.1 GeneralSee Volume 2 Section 3 Chapter 6.The site selected for the assembly of the GP mast framework should be of sufficient size to accommodate either the 10 meter or the 15 meter mast.It is also recommended to select a relatively well levelled site to avoid twists or bends in the mast construction which may create difficulties in joining the parts.To facilitate the work, four trestles are needed, made of timber from the transport crates or other. See Vol. 2 Section 3 Chapter 6.Align the trestles, one pair for the first section, parallel to each other, approximately 4 meters apart. See marked-up drawing 16641A3/16642A3.Before the work starts, the colours of the sections should be observed as follows:Tightening and securing of bolts:Recommended torque’s are: M12 - 75NM; M24 - 700NM (ungreased bolts). Preferred tighten-ing method is “Turn of nut” method: 1. Snug tight using 0,6 x recommended torque. (0,36 x for greased bolts) C1 (clearance length) = Distance between bolthead and nut. See fig. 3-110 meter mast: Top section: OrangeBottom section: WhiteRef. drawing 16641A3.15 meter mast: Top section: OrangeMiddle section: WhiteBottom section: OrangeRef. drawing 16642A3.Turn nut - 1/3 turn if C1< 2x bolt dia. 1/2 turn if C1 is between 2 and 4x bolt dia. 2/3 turn if C1 is between 4x and 8x bolt dia.

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6.Figure 3-1 Securing: Bolts should be secured by either deformation of threads by use of a chisel or by the use of lock-nuts (double nuts). Ref. Fig. 3-2 .Figure 3-2 3.2 Bottom Section3.2.1 Vertical BeamsPlace two vertical main legs, pos. 1 dwg.16612A3 on the trestles.3.2.2 Bottom FlangeAssemble vertical main legs and bottom flanges, pos. 8 DWG. 16612A3 and also junction plates pos. 9.HBK1130-1SPRING W.FLAT W.C1FLAT W.SECURING N.MAIN N.ADJUST N.Double Nut MethodPunching of Nutflat and spring washersMAIN NUTFLAT W.RecommendedADJUST NUTHBK 1131-1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.3.2.3 Diagonal strutsPosition and bolt diagonal struts, starting with the shorter, pos. 2, and continuing with the longer pos. 3 in accordance with pos. 2, 3, and 4, DWG. 16612A3.3.2.4 Third vertical legRepeat the procedure as for 3.2.2 and 3.2.3. Bolt third leg to end of diagonal struts of the other two legs.3.2.5 LadderHoist/lift the ladder pos. 20 into the centre of the section, assemble 8 PC’s of brackets pos: 11 and connect them to the ladder acc. dwg. 16612A3. Lift up the ladder, and connect pos. 11 as shim between the bracing. Don't tighten up the bolts before all brackets are connected and adjusted.3.2.6 Locking of nutsTorque - load nuts as follows: According to general instructions Chapter 3.1 M-12: 75 Nm.3.3 Middle section3.3.1 Vertical legsRepeat procedure as for 3.2.1 and onwards, (except 3.2.2 bottom flanges)127(7KHVHFRQGPLGGOHVHFWLRQZLOORQDPPDVWEHWKHWRSVHFWLRQ3.4 Top section3.4.1 GeneralFollow steps described under MIDDLE SECTION, except for "section joints" which in this case is pos. 10.3.4.2 Horizontal strutsPosition and bolt horizontal struts pos 5 at the top of the upper mast section. Ref. dwg. 16612A3.3.5 Obstruction light3.5.1 Obstruction light bracketThe obstruction light bracket (pos. 7) is fixed to two of the horizontal struts at the top, pos. 5. Dwg. 16612A3.

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$63.5.2 Obstruction lightThe obstruction light is mounted on the bracket (pos. 7) and the power cable is fixed with cable ties to the rear side of the ladder or inside the cable trunking if space is available.3.6 Antenna suport3.6.1 Adjustment railsAs support for the antennas, the mast is equipped with rails for vertical adjustment, see Dwg. No.: 16643A33.6.2 Mounting of supportsThe vertical adjustment rails are mounted in the mast structure in accordance with drawing dwg. 16643A3. The rails should be offset according to calculation made for the site in ques-tion. They should be positioned horizontally such that the centre of the rail lines up with the antenna offset given by the site data, and vertically so the centre lines up with the antenna height. See example Dwg. No.: 16641A3/16642A3.If the offset is too wide to be adjusted with the vertical rail, position the rail as far as possible to the side and do the rest of the adjustment by sliding the antenna in the bracket pos. 2 dwg. 16792A3.3.6.3 Antenna assemblyThe antenna assembly, which comprises the radom and the antenna, is mounted to the verti-cal adjustment rail. See dwg. 16792A3.If NM antennas are supplied, see dwg. 10039A3.From site data determine the exact distance between the antennas and to the ground. Adjust the vertical antenna positions according to these data. Tolerance: +/-5 mm.From site data determine the antenna offsets, i.e. the relative horizontal displacements between the antennas. Adjust the offsets. Tolerance: +/-5 mm.From site data determine the antenna forward shift i.e. relative vertical displacement. Adjust the forward shift. Tolerance ± 2mm.3.7 Cable trunks3.7.1 Cable trunk bracketsAll cable trunk brackets are prepared with 3 evenly spaced holes of 3.2 mm for cable trunk fixes.Brackets are mounted to the ladders in accordance with dwg. 16612A3. Cable trunks are mounted to the brackets with rivets.

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.3.7.2 Antenna cablesAntenna cables and monitor cables are carefully laid out in the cable trays such that equal length of all cables is sufficient to be guided into the shelter. However, the excess cables shall be neatly bundled and temporarily fixed to the antenna mast, and protected from damage dur-ing later mast erection.Connect the cable end connectors to the antenna receptacle temporarily in order to avoid dust and water problems.3.8 Antenna mast erection3.8.1 Erection of the mastA mobile crane will be needed in erecting the mast into the vertical position and placed onto the concrete foundation. Ref. dwg. 16641A3/16642A3.The vertical position of the mast must be checked after erection. Adjustment of the mast is made by means of the lower nuts ref. dwg. 7084A3 on the retaining bolts. The tolerance is +/-0,02 degrees. (Top of mast should be within +/- 5 mm referred to vertical centreline.)3.8.2 Locking of nuts Torque-load nuts as follows:M24: 700 Nm and secure them according to Chapter 3.1.3.9 Cable installation into shelter3.9.1 Cable tubeA cable tube is installed from the upper part of the shelter to the antenna mast, such that the tube ending in the mast is positioned a few centimetres lower than the other end in the shelter. (Prevents water from entering into the shelter).3.9.2 Cable installationCarefully unwind the antenna cable coils and feed the cables through the cable tube. Install the cables inside the shelter ending at the Antenna distribution unit and Monitoring combining unit. The excess cables are pulled back through the cable tube and fixed in the antenna mast.The power cable is installed through the cable tube to the Mains Distribution box.

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.4 Near field monitor4.1 Cable installationThe NF Monitor cable is first carefully rolled out and positioned such that there is no risk for damage during installation in the cable duct.The cable is fixed to the pulling rope at the NF position end together with and extra rope for maintenance purpose.Connectors and cable labels must be protected against dust, water and wear during the pull-ing operation.The cable is pulled through the duct into the shelter and installed and connected to the NF Monitor Input of the cabinet.4.2 NF Monitor antenna assemblyThe mast and antenna is assembled complete in horizontally position according to dwg.no. 7058 A3.The antenna element is positioned as accurate as possible according to site date for NF mon-itor antenna height.Install a gasket in the top cover.On the NF monitor cable remove the connector and thread the cable from the bottom of the mast through the gasket.The mast is erected by three persons. Make sure that the cable at the bottom end is not bent excessively during mast erection.The vertical position of the mast must be checked after the erection. Adjustments of the mast is made by means of the lower nuts of the base section.The cable is installed from the top along the mast leaving adequate excess for antenna height adjustments.(Estimated adjustments: +/-60 cm.)

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.5 Marker beacon installation antenna assembly5.1 Antenna assemblySee Volume 2 Section 4.The LPDA is first mounted to the antenna mast, horizontally on the ground.Position the assembly such that the base is close to the foundation bolts.5.2 Antenna Cables installationFor Dual Antenna system the Distribution Network is preferably installed inside shelter.Antenna- and monitor cables are then carefully rolled out and positioned such that there is no risk for damage during installation.Install the cables through the hole below the end of the LPDA and out through the bottom of the mast.Fit the cable connectors into the appropriate A and M marked N-connectors in the LPDA.Carefully thread/pull the cables further into the shelter so there is no loop between the antenna mast base and the fundament.5.3 Antenna Mast erectionA crane is needed to erect the antenna mast assembly.Install the antenna in direction with the elements parallel to the runway.During erection make sure that there will be no twist or strain to the cables near the antenna base as the mast is lowered onto the base. If necessary carefully pull the cables from the shelter end to account for the excess cable length inside the base.

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.SECTION 2SHELTER INSTALLATIONTable of contents1 General ...................................................................................................................... 32 Mechanical installation LLZ/GP ..............................................................................52.1 Mounting Kit MK1343A.......................................................................................52.2 Moving RF Connectors.......................................................................................63 Electrical Installation LLZ/GP..................................................................................93.1 Connection Overview ......................................................................................... 93.2 Power and Battery.............................................................................................. 103.3 RF Inputs............................................................................................................ 123.4 RF Outputs......................................................................................................... 123.5 DC Loop (Localizer only)....................................................................................133.6 Remote Control ( CABINET) ..............................................................................143.7 PC and Modem ..................................................................................................153.8 DME (localizer only) ........................................................................................... 163.9 Analog Inputs ..................................................................................................... 183.10 Digital Inputs and Outputs..................................................................................193.11 Battery Warning.................................................................................................. 204 Mechanical Installation Marker Beacon .................................................................214.1 Marker beacon Cabinet......................................................................................215 Electrical installation marker beacon .....................................................................235.1 Marker beacon cabinet.......................................................................................235.1.1 Connection Overview..................................................................................235.2 RF In and Out.....................................................................................................245.3 Battery................................................................................................................ 245.4 Mains.................................................................................................................. 265.5 Remote Control cabinet...................................................................................... 275.6 PC and Modem ..................................................................................................285.7 Analogue Inputs .................................................................................................305.8 Digital Inputs and Outputs..................................................................................316 Remote Control Connections (TWR) ......................................................................336.1 Remote Master Connection................................................................................336.2 Power Supply Connection.................................................................................. 346.3 Remote slave connection...................................................................................356.4 Interlock switch connection ................................................................................36

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.1 GeneralEquipments are installed according to interior drawings. All electrical equipment including antenna systems and monitor antennas must be connected to a common earth point. See Volume 2 Chapters «Grounding» for resp. Equipment.Cables are routed the shortest distance in the cable trunks. Use terminal shoes at the cable ends before connecting them to cabinet terminals.Coax cables must be carefully formed along the trunking to avoid damage.Line transient absorbers must be installed at the entrance of the remote control lines, both in the shelter and the tower.

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.2 Mechanical installation LLZ/GPThe «NM7000» cabinet is constructed for mounting on a wall. For easy operation, the key-board/display section should be in eye/shoulder height (140-160cm). The RF connectors may be mounted either on the cabinet top or the cabinet bottom. The free space required around the cabinet is approximately one by one meter, see figure 2-1Figure 2-1 «NM7000» required mounting space (top view).2.1 Mounting Kit MK1343ANAVIA AVIATION supplies a wall mounting kit, MK1343A. This kit is dimensioned for stan-dard 60 cm space between studs. For easy mounting, place the cabinet on the rest screws (B) before entering the mounting screws (A). This is shown in the enlarged view in figure 2-2.0.9m1.0mHBK594-2

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6Figure 2-2 «NM7000» mounted on wall with MK1343A.2.2 Moving RF ConnectorsIf desired the RF connectors may be moved from the cabinet top to the bottom or vice versa, as illustrated in figure 2-3. The back section (F) of the main cabinet consists of a connector plate and a blind plate that are interchangeable. These plates are identical, except for the connectors. POWER POWERAdjustment screw11Flat washer M8Split lock washer M8Screw M8x25BAAAAHBK597-1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.To interchange the plates, follow these instructions:• Release the nuts (A), washers (B) and flanges (C) on the plates.• Release the ground connections (D) on the connector plate and (H) on the blind plate.• Interchange the plates.• Remount the nuts, washers and flanges in the order shown.• Remount the ground connections (D) and (H). Make shore they are located on the hinge (G) side of the cabinet.Figure 2-3 Moving the RF connectors to the cabinet top.CLDNFCABABCSB CLRCLR DS SBO CLRESBO CSBAFBCGHHBK596-1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.3 Electrical Installation LLZ/GPThis paragraph describes the external electrical connections of the «NMnr» main cabinet.3.1 Connection OverviewThe ILS main cabinet consists of three connector sites, illustrated in Figure 3-1. • The ILS RF signals to and from the antenna system are connected at the top of the main cabinet. These connectors may be moved to the top, see Mechanical Installation.• The power supply (supplies) and the backup battery are connected to the power connector rail inside the cabinet back section.• All other external connections are sited on the CI1210A connection interface board inside the cabinet back section.Figure 3-1 ILS main cabinet connection overview.RF CONNECTIONSCABLE FEEDTHROUGHCOU/SBOCLR/SBOCLR/CSBOUTCOU/CSBCLRDSNFIN CL1 AC LEVEL MEASUREMENTCI 1210A CONNECTIONS8 DIGITAL INPUT/OUTPUT3 DIFFERENTIAL ANALOG2 TEMP SENSORS1 DME1 REMOTE CONTROL3 RS 2324 DC LOOPSBATTERY +27V0VPOWER RAIL CONNECTIONSSUPPLYPOWER +27V0VHBK574-2

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$63.2 Power and BatteryThe power supply and the backup battery are connected to the power connector rail inside the cabinet back section as shown in Figure 3-2 and 3-3. If two power supplies are used, these are parallel coupled inside one of the power supplies (see Dwg.no.: 17370A3). The cables used should have 6mm2 intersection.Figure 3-2 Power and backup battery connections.Battery0V +27VPower Supply0V +27VHBK576-2

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.Figure 3-3 Power Supply connections. 234 819675NLG++ - -Currentsharing+NL G12 54376 98-+-To equipment0V+27V Power supplyBattery warning 1Battery warning 2220VFuseX FuseY220VCHARGER 1 CHARGER 2POWER SUPPLY CONNECTIONSsharingCurrent

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$63.3 RF InputsThe RF inputs are:• Course Line - CL.• Near Field Antenna - NF.• Displacement Sensitivity - DS.• Clearance - CLR (two frequency applications only).These are connected as shown in Figure 3-4 (front view).Figure 3-4 RF input connections.3.4 RF OutputsThe RF outputs are sited at the cabinet top as illustrated in Figure 3-5. The connections are:All applications:• COU SBO - COUrse Tx SideBand Only.• COU CSB - COUrse Tx Carrier and SideBand.Two frequency applications:• CLR SBO - CLeaRance Tx SideBand Only.• CLR CSB - CLeaRance Tx Carrier and SideBand.Figure 3-5 RF output connections.NF CL CLR DSHBK577-2COUCSBCOUSBOCLRCSBCLRSBOHBK578-2

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.3.5 DC Loop (Localizer only)The DC loops are connected to the CI1210A connection interface board in the cabinet back section. Placement and pin out are illustrated in Figure 3-6. •DL_REF* are the reference voltages from the main cabinet.•DL_DETECT* are the return voltages from the antennas.•GND is main cabinet ground.Suitable female connectors are Weidemüller BLZ-5.08/6 or equivalent.Figure 3-6 DC loop connections.TEMPINDOOR TEMPOUTDOOR ACLEVEL ANALOGCH.1 ANALOGCH.2 ANALOGCH.3 DIGITALPORT A DIGITALPORT B DIGITALPORT C DIGITALPORT DTO MB1203RS232 RS232 RS232 REMOTECONTROLDC-LOOP DC-LOOP DMELOCAL REMOTE 2 REMOTE 1 CH.1&2 CH.3&416DC-LOOPCH.1&2DC-LOOPCH.3&41 - Ch 1 In2 - Ch 1 Out3 - GND4 - Ch 2 In5 - Ch 2 Out6 - GNDCI 1210A1 - Ch 3 In2 - Ch 3 Out3 - GND4 - Ch 4 In5 - Ch 4 Out6 - GND16BATTERYWARNINGHBK579-2RADIO LINK

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$63.6 Remote Control ( CABINET)The remote control is connected to the CI1210A connection interface board as illustrated in Figure 3-7. The connection of the remote control, remote slave panel and interlock switch is done at the remote control site and covered in Section 2 6.1-6.4.•FSK_[P,N] is the modem line pair.•GND is main cabinet ground.For normal FSK modem operation the straps S9-11 on CI1210A should be mounted.A suitable female connector is Weidemüller BLZ-5.08/4 or equivalent.Figure 3-7 Remote control connection.TEMPINDOOR TEMPOUTDOOR ACLEVEL ANALOGCH.1 ANALOGCH.2 ANALOGCH.3 DIGITALPORT A DIGITALPORT B DIGITALPORT C DIGITALPORT DTO MB1203RS232 RS232 RS232 REMOTECONTROLDC-LOOP DC-LOOP DMELOCAL REMOTE 2 REMOTE 1 CH.1&2 CH.3&4REMOTECONTROL1 - GND2 - FSK_P3 - FSK_N4 - GNDCI1210A14S9-14BATTERYWARNINGHBK580-1RADIO LINK

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.3.7 PC and ModemPC terminals and modems are connected to the standard pin out RS232, 9 pins DSUB con-nectors on the CI1210A connection interface board as illustrated in Figure 3-8. Recom-mended connections are:• LOCAL - the PC located at the ILS main cabinet site. • REMOTE 2 - distant PC terminals connected through a modem.• REMOTE 1 - the PC located at the airport technical maintainance site.Figure 3-8 PC and modem connections.TEMPINDOOR TEMPOUTDOOR ACLEVEL ANALOGCH.1 ANALOGCH.2 ANALOGCH.3 DIGITALPORT A DIGITALPORT B DIGITALPORT C DIGITALPORT DTO MB1203RS232 RS232 RS232 REMOTECONTROLDC-LOOP DC-LOOP DMELOCAL REMOTE 2 REMOTE 1 CH.1&2 CH.3&4CI1210A15691 - CD (REMOTE 2 only)2 - RXD3 - TXD4 - DTR (REMOTE 2 only)5 - GND6 - DSR (REMOTE 2 only)7 - RTS8 - CTS9 - Not connectedBATTERYWARNINGHBK581-1RADIO LINK

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$63.8 DME (localizer only)Distance Measurement Equipment DME is connected to the CI1210A connection interface board as illustrated in Figure 3-9.•ACT_DME[P,N] is the positive and negative terminal of the DME active signal from the DME, respectively.•IN_DME[P,N] is the positive and negative terminal of the morse code envelope signal from the DME, respectively.•OUT_DME[P,N] is the positive and negative terminal of the morse code envelope signal to the DME, respectively.A suitable female connector is Weidemüller BLZ-5.08/6 or equivalent.Figure 3-9 DME connections.TEMPINDOORTEMPOUTDOORACLEVELANALOGCH.1ANALOGCH.2ANALOGCH.3DIGITALPORT ADIGITALPORT BDIGITALPORT CDIGITALPORT DTO MB1203RS232 RS232 RS232 REMOTECONTROLDC-LOOP DC-LOOP DMELOCAL REMOTE 2 REMOTE 1 CH.1&2 CH.3&41 - ACT_DMEP2 - ACT_DMEN3 - IN_DMEP4 - IN_DMENCI1210A16S1-8DME5 - OUT_DMEP6 - OUT_DMENBATTERYWARNINGHBK582-1RADIO LINK

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.Figure 3-10 DME master connections.If the DME shall be used as ident master, connect as shown in Figure 3-10. In the RMM pro-gram, CLR modulation and DME interface dialogue (see Operators Manual), set DME as master and DME active signal to OPEN. The LLZ will now transmit the DME dictated morse code. If the LLZ does not receive any ident signal for approximately 20 seconds, the LLZ will start to transmit its own programmed morse code. When the DME signal returns, the LLZ will start to transmit the DME code instantaneously.Figure 3-11 LLZ master connections.If the LLZ shall be used as ident master, connect as shown in Figure 3-11. In the RMM pro-gram, CLR modulation and DME interface dialogue (see Operators Manual), set LLZ as mas-ter and the DME active signal according to the DME’s manual. When the DME is active, the LLZ will send every forth ident word to the DME. When the DME is inactive the LLZ will be keying four out of four words. If the LLZ shall be keying three out of four words whether the DME is active or not, disconnect the DME ACTIVE wires and program the DME active signal to OPEN.123123123123123123123123S1S2S3S4S5S6S7S8DME ILSCI1210AP8IDENT FROM DME2.7K2.7K123456HBK770-1123123123123123123123123S1S2S3S4S5S6S7S8DME ILSCI1210AP8DME ACTIVEIDENT TO DME2.7K2.7K123456HBK771-1

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$63.9 Analog InputsThe analog inputs are connected to the CI1210A connection interface board as illustrated in Figure 3-12. The inputs are:• ANALOG CH.1-3 - three differential DC analog inputs, P is the positive and N is the nega-tive terminal. Maximum voltage: ±15V.Input impedance: 10kohms.• TINDOOR, TOUTDOOR - temperature measurement inputs with interface to an LM35 tem-perature sensor.Maximum voltage: ±15V.Input impedance: 10kohms.• AC LEVEL - AC level measurement input. Intended for use with a battery eliminator (i.e. 220/9VAC) to monitor the mains voltage.Maximum voltage: 24Vpp.Input impedance: 10kohms.Suitable female connectors are Weidemüller BLZ-5.08/4 or equivalent.Figure 3-12 Analog input connections.TEMPINDOOR TEMPOUTDOOR ACLEVEL ANALOGCH.1 ANALOGCH.2 ANALOGCH.3 DIGITALPORT A DIGITALPORT B DIGITALPORT C DIGITALPORT DTO MB1203RS232 RS232 RS232 REMOTECONTROLDC-LOOP DC-LOOP DMELOCAL REMOTE 2 REMOTE 1 CH.1&2 CH.3&4TEMP*1 - VDD2 - T*DOOR3 - GND4 - Not connectedCI1210A14LM35Bottomview1 - VACP2 - GND3 - VACN4 - Not connectedACLEVEL1 - ANLG*P2 - GND3 - ANLG*N4 - Not connectedANALOGCH.*1414141414V+VtempGNDBATTERYWARNINGHBK583-1RADIO LINK

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.3.10 Digital Inputs and OutputsEight bidirectional digital channels (numbered 0-7) are sited on the CI1210A connection inter-face board as illustrated in Figure 3-13.Logic levels: TTL.Input impedance: 560ohms.Suitable female connectors are Weidemüller BLZ-5.08/4 or equivalent.Figure 3-13 Digital input/output connections.TEMPINDOOR TEMPOUTDOOR ACLEVEL ANALOGCH.1 ANALOGCH.2 ANALOGCH.3 DIGITALPORT A DIGITALPORT B DIGITALPORT C DIGITALPORT DTO MB1203RS232 RS232 RS232 REMOTECONTROLDC-LOOP DC-LOOP DMELOCAL REMOTE 2 REMOTE 1 CH.1&2 CH.3&4CI1210A1 - USER_DIG52 - GND3 - USER_DIG44 - GND14141414DIGITALPORT C1 - USER_DIG32 - GND3 - USER_DIG24 - GNDDIGITALPORT B1 - USER_DIG12 - GND3 - USER_DIG04 - GNDDIGITALPORT A1 - USER_DIG72 - GND3 - USER_DIG64 - GNDDIGITALPORT DBATTERYWARNINGHBK575-1RADIO LINK

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$63.11 Battery WarningTwo inputs for main power supply failure (backup battery active) are sited on the CI 1210A connection interface board as illustrated in Figure 3-14. See also Figure 3-3.Logic levels: Normally high (5V) ( 0V =battery warning).Input impedance: 10kohms.Suitable female connectors are Weidemüller BLZ-5.08/4 or equivalent.Figure 3-14 Battery warning connections.TEMPINDOOR TEMPOUTDOOR ACLEVEL ANALOGCH.1 ANALOGCH.2 ANALOGCH.3 DIGITALPORT A DIGITALPORT B DIGITALPORT C DIGITALPORT DTO MB1203RS232 RS232 RS232 REMOTECONTROLDC-LOOP DC-LOOP DMELOCAL REMOTE 2 REMOTE 1 CH.1&2 CH.3&4BATTERYWARNING1 - BATT.WARN. CHARGER 12 - GND3 - BATT.WARN. CHARGER 24 - GNDCI 1210A14BATTERYWARNINGHBK602-2RADIO LINK

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.4 Mechanical Installation Marker BeaconThis chapter gives a brief instruction on the mechanical installation of the Marker Beacon cab-inet and antenna. 4.1 Marker beacon CabinetThe NM7050 cabinet is constructed for mounting on a wall. For easy operation, the keyboard and display section should be in eye/shoulder height (140-160cm). The ventilation holes at the bottom of the cabinet should be kept uncovered to ensure proper cooling.The cabinet is 45 cm wide, 34 cm deep and 27 cm height and weighs about 5 kg.When mounting the cabinet on a wall, do the following:• First drill the holes according to Figure 4-1.• Mount the upper screws. Leave 6 mm distance from the screw head to the wall.• Hang the cabinet on these screws, using the key holes on the mounting rails• Mount the lower screws • Tighten all screws•Figure 4-1 Mounting the cabinet on a wall.MARKER BEACONONOFFOFFBATTERYONLOCAL RS232POWERMAINSREMOTELOCALAUTOMANUALWRITEPROTECTMAINTX TO AIR+ON/OFFSTBYMAINTBATTDISAGRPARAMALARMWARNINGOVERCHANGENORMALSERVICE TX1ESC-PREV NEXTREADTX2QUICKENTER405Hex lag screw 6x50Hex lag screw 6x50Washer M6Washer M6340451 mm5HBK 860-1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.5 Electrical installation marker beacon5.1 Marker beacon cabinet5.1.1 Connection OverviewAll electrical connections except the local PC connection, the mains connection and the RF IN and OUT connections are on the CI1376 connection interface board inside the cabinet.Figure 5-1 Marker Beacon main cabinet connection overviewGNDLNRF INRF OUTON ONOFF24V DC OFFPOWERMAINSON/OFFLOCAL RS232DISAGRSTBYMAINTBATTPARAMREMOTE AUTOLOCAL MANUALCHANGEOVERPROTECTWRITETX1/TX2MAINTX TO AIRNORMALWAR NINGALARMSERVICETX1 TX2MARKER BEACON SYSTEMESC PREV NEXT ENTERCABINET UNDERSIDEFRONT VIEW WITH FRONT PLATEFRONT VIEW WITHOUT FRONT PLATE RF IN AND OUTMAINS POWERLOCAL PC (RS 232)REMOTE CONTROL (RS 232)REMOTE PC (RS 232)3 ANALOGUE CHANNELSAC LEVEL4 DIGITAL PORTSTEMP. INDOOR AND OUTDOORBATTERYANTISTATHBK784/1

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$65.2 RF In and Out• The output signal RF OUT is connected to the antenna with N-connectors and 50 Ω coaxial cable.• The input signal RF IN is connected to the antenna probe with N-connectors and 50 Ω coaxial cable.Figure 5-2 RF cable connection5.3 BatteryThe external backup battery is connected between Batt Gnd (-) and Batt +24V (+) on the con-nector marked Battery on CI 1376. A 16Ah battery gives approximately six hours backup time with 5-8 hours charging time dependent on model. For longer backup time an external charger is required to be able to charge the battery within a reasonable time. An external battery protection circuit (like Nor-marcs BP 543) has to be connected between the Ext. Charger (+) and BATT GND (-) input. In addition Mains directly on NM 7050 has to be disconnected. Figure 5-4 shows the connec-tions schematically.RF OUT RF INHBK785/1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.Figure 5-3 Battery connectionFigure 5-4 External charger connectionCI 1376REMOTECONTROLLINETEMPOUTDOORTEMPINDOORAC LEVEL ANA CHA1 ANA CHA2 ANA CHA3DIG PORT A DIG PORT B DIG PORT C DIG PORT DBATT GNDEXT CHARGEBATT +24V123BATTERYBATT GNDEXT CHARGEBATT +24VBATTERYHBK786/1ACDCBP 543BATTERYEXT.CHARGEBATT +24VBATT GNDMAINSEXTERNALCHARGERBATTERYPROTECTIONNM 7050HBK863/1

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$65.4 Mains The mains power cable connections are underneath the cabinet. They are covered by a alu-minium plate fastened with four screws. The cable itself is threaded through the cable gland and the three wires are connected to the terminals N, L and GND shown below in Figure 5-5.Figure 5-5 Power connectionMAINS POWERGNDLNGROUND CABLE CONNECTIONHBK787/1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.5.5 Remote Control cabinetThe remote line and remote controis connected to the CI 1376 connection interface board as illustrated in Figure 5-6. • FSK_[A,B] is the modem line pair.• GND is main cabinet groundA suitable female connector for the remote line is Weidemüller BLZ-5.08/4 or equivalent.Alternatively the remote control connection is done with a RS 232 interface, standard pin out 9pins DSUB.Figure 5-6 Remote control connectionCI 1376PB 1378REMOTECONTROLLINETEMPOUTDOORTEMPINDOORAC LEVEL ANA CHA1 ANA CHA2 ANA CHA3REMOTE RMMRS232REMOTE CONTOLRS232CONFIGURATION1 - GND2 - RC_LINE B4 - Not used1 - Not used3 - RXD2 - TXD4 - Not used5 - GND6 - Not used7 - Not used8 - Not used9 - Not usedREMOTECONTROLREMOTECONTROLLINERS-232HBK788/32 - RC_LINE A

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$65.6 PC and ModemModem connections for remote PC are the standard pin out RS232, 9 pins DSUB connector on the CI1376 connection interface board marked remote-rmm as illustrated in Figure 5-7.For local PC connection use the RS232 on front panel Figure 5-7.Figure 5-7 Modem and modem battery backup connectionCI 1376PB1378REMOTECONTROLLINETEMPOUTDOORTEMPINDOORAC LEVEL ANA CHA1 ANA CHA2 ANA CHA3REMOTE RMMRS232REMOTE CONTOLRS232CONFIGURATIONDIG PORT A DIG PORT B DIG PORT C DIG PORT D1-CD2-RXD3-TXD4-DTR5-GND6-Not used7-RTS9-CTS9-Not usedREMOTE RMM6195HBK789/1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.Figure 5-8 Local PC RS232 connection1 - Not used2 - RXD3 - TXD4 - Not used5 - GND6 - Not used7 - RTS8 - CTS9 - Not usedHBK790-1

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$65.7 Analogue InputsThe analogue inputs are connected to the CI1376 connection interface board as illustrated in Figure 5-9.The inputs are:• Analogue Channel 1-3 - three differential DC analogue inputs, P (pin-1) is the positive and N (pin-3) is the negative terminal, and pin 2 is GND.Maximum voltage: ±15VInput impedance: 10kΩ• Temp Indoor and Outdoor - temperature measurement inputs with interface to an LM35 temperature sensor.Maximum voltage: ±15VInput impedance: 10kΩ• AC Level - AC level measurement input. Intended for use with a battery eliminator to moni-tor the mains voltage.Maximum voltage: 24VppInput impedance: 10 kΩFigure 5-9 Analogue input connectionsCI 1376PB 1378REMOTECONTROLLINETEMPOUTDOORTEMPINDOORAC LEVEL ANA CHA1 ANA CHA2 ANA CHA3REMOTE RMMRS232REMOTE CONTOLRS232CONFIGURATIONDIG PORT A DIG PORT B DIG PORT C DIG PORT D1-ANLG*P2-GND3-ANLG*N4-Not usedANALOGUECHANNEL 1-31-VACP2-GND3-VACN4-Not usedAC LEVEL1-VDD2-T*DOOR3-GND4-Not usedTEMP *V+VtempGNDLM 35Bottom viewHBK791/1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.5.8 Digital Inputs and OutputsEight bi-directional digital channels (numbered 0-7) are sited on the CI1376 connection inter-face board as illustrated in Figure 5-10.Logical levels: TTLInput impedance: 560Ω.A suitable female connector is Weidemüller BLZ-5.08/4 or equivalent.Figure 5-10 Digital input/output connections1- DIGIN 12- GND3- DIGIN 04-GND1- DIGIN 32- GND3- DIGIN 24-GND1- DIGIN 52- GND3- DIGIN 44-GND1- DIGOUT 02- GND3- DIGOUT 14-GNDDIGITAL PORTSABCDCI 1376PB 1378REMOTECONTROLLINETEMPOUTDOORTEMPINDOORAC LEVEL ANA CHA1 ANA CHA2 ANA CHA3REMOTE RMMRS232REMOTE CONTOLRS232CONFIGURATIONDIG PORT A DIG PORT B DIG PORT C DIG PORT DHBK792/1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.6 Remote Control Connections (TWR)6.1 Remote Master ConnectionThe remote control is connected to the corresponding ILS by connecting the REMOTE CON-TROL connector on CI1210 (ILS) or CI1376 (Marker Beacon) to P9 on MB1346 as shown in figure 6-1. Suitable female connectors are Weidemüller BLZ-5.08/4 or equivalent. 600 ohms cable should be used.Figure 6-1 Remote control to ILS connectionREMOTECONTROL1 - GND2 - FSK_P3 - FSK_N4 - GNDJ2 P3P6P7P4P5P9P10P8NORMARCOPTO OUT2-ALARM (E)1-ALARM (C)4-NORM (E)5-WARN (C)6-WARN (E)7-STBAL (C)8-STBAL (E)3-NORM (C)GND5V24VV_DIMGND5V24VV_DIMPOWER OUT POWER INAUX IN/OUTSLAVEDIRECTINTERLOCKTXOFFALARMLINE ALINE BRX ARX BTX ATX BSLAVE RS485J1ABC153020251510ALT.LINKMB1346P91 - TXOFF2 - ALARM3 - LINE_A4 - LINE_BCI 1210 on corresponding ILSorCI 1376oncorrespondingMarker BeaconHBK 1135-2

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$66.2 Power Supply ConnectionThe power supply to the remote control is connected according to Figure 6-2. The battery charger is connected to P2 on the MB1347 - power supply motherboard. Output connector P3 on MB1347 is connected to input connector P4 on MB1346 - remote control motherboard. Several MB1346’s are serial linked by connecting P5 on one board to P4 on the next.Suitable female connectors are Weidemüller BLZ-5.08/4 or equivalent.Figure 6-2 Remote control power supply connectionsJ2 P3P6P7P4P5P9P10P8NORMARCOPTO OUT2-ALARM (E)1-ALARM (C)4-NORM (E)5-WARN (C)6-WARN (E)7-STBAL (C)8-STBAL (E)3-NORM (C)GND5V24VV_DIMGND5V24VV_DIMPOWER OUT POWER INAUX IN/OUTSLAVEDIRECTINTERLOCKTXOFFALARMLINE ALINE BRX ARX BTX ATX BSLAVE RS485J1ABC153020251510ALT.LINKMB1346P2P3S1GND24VPOWER INGND5V24VV_DIMPOWER OUTV_DIM=24VMB1347NORMARC302520151051ABJ1J2 P3P6P7P4P5P9P10P8NORMARCOPTO OUT2-ALARM (E)1-ALARM (C)4-NORM (E)5-WARN (C)6-WARN (E)7-STBAL (C)8-STBAL (E)3-NORM (C)GND5V24VV_DIMGND5V24VV_DIMPOWER OUT POWER INAUX IN/OUTSLAVEDIRECTINTERLOCKTXOFFALARMLINE ALINE BRX ARX BTX ATX BSLAVE RS485J1ABC153020251510ALT.LINKMB1346From 24VDCpowersupplyHBK 1136-1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.6.3 Remote slave connectionThe remote slave panel SF1344 is connected to the corresponding remote control’s mother-board by connecting P3 on MB1346 to P1 on SF1344. P10 on MB1346 is not used. See Fig-ure 6-3.Suitable connectors are standard 25 pins female DSUB (Harting 0967 025 0442 and 0967 225 4704 or equivalent), connected by a 10 wire 1:1 cable.Figure 6-3 Remote slave connectionJ2 P3P6P7P4P5P9P10P8NORMARCOPTO OUT2-ALARM (E)1-ALARM (C)4-NORM (E)5-WARN (C)6-WARN (E)7-STBAL (C)8-STBAL (E)3-NORM (C)GND5V24VV_DIMGND5V24VV_DIMPOWER OUT POWER INAUX IN/OUTSLAVEDIRECTINTERLOCKTXOFFALARMLINE ALINE BRX ARX BTX ATX BSLAVE RS485J1ABC153020251510ALT.LINKMB13461:1To P1 onSF134411314251 - GND2 - ALARM3 - WARNING4 - NORMAL7 - GND15 - V24P19 - ON_OFF21 - SILENCE23 - INTERLOCK (if used)25 - BUZZERHBK 1137-1

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$66.4 Interlock switch connectionThe interlock switch is either connected to P8 on MB1346 (remote control motherboard) or to P2 on SF1344 (remote slave panel), see Figure 6-4.Figure 6-4 Interlock switch connection21MB1346 / P8ORSF1344 / P2INTERLOCK SWITCHRWYA RWYB211212INTERLOCKGND1254 21LLZ runway AGP runway ALLZ runway BGP runway BHBK775-2

 SECTION 3ANTENNA SYSTEMS ADJUSTMENTS PROCEDURETable of contents1 NM 3522 6 elements antenna system adjustments - LLZ .....................................71.1 Mechanical alignment of antenna array .............................................................71.1.1 Right angle points with reference to runway center line .............................. 71.1.2 Spacing distance between LPDA’s..............................................................71.1.3 Vertical alignment of LPDA support masts ..................................................71.1.4 Azimuth alignment of LPDA’s ......................................................................71.2 Electrical measurements....................................................................................71.2.1 CSB and SBO cables ..................................................................................71.2.2 CSB/SBO phasing .......................................................................................81.2.3 Antenna cable lengths (Electrical phase equality).......................................81.2.4 Antenna pair phasing................................................................................... 81.2.5 Phase and amplitude transfer measurement............................................... 101.2.6 Antenna return loss......................................................................................111.3 Course sector width adjustment......................................................................... 111.3.1 DDM check of ADU O/P (output port)..........................................................121.3.2 DDM field check...........................................................................................131.4 Monitor combining unit (MCU) adjustments ....................................................... 131.4.1 Course Line ................................................................................................. 131.4.2 Course Sector.............................................................................................. 131.5 Near field monitor adjustments...........................................................................131.5.1 Mechanical alignment ..................................................................................131.5.2 Final electrical position adjustment.............................................................. 131.6 DC-Loop adjustment and testing........................................................................141.6.1 DC-LOOP adjustment.................................................................................. 141.6.2 Antenna fault condition testing.....................................................................142 NM 3523B 12 Elements antenna system adjustments - LLZ (Single frequency)152.1 Mechanical alignments of antenna array............................................................152.1.1 Right angle points with reference to runway centre line .............................. 152.1.2 Spacing distance between LPDA’s..............................................................152.1.3 Vertical alignment of LPDA support masts ..................................................152.1.4 Azimuth alignment of LPDA’s ......................................................................152.2 Electrical measurements....................................................................................152.2.1 CSB and SBO cables ..................................................................................152.2.2 CSB/SBO phasing .......................................................................................162.2.3 Antenna cable lengths (Electrical phase equality).......................................162.2.4 Antenna pair phasing................................................................................... 162.2.5 Phase and amplitude transfer measurement............................................... 182.2.6 Antenna return loss......................................................................................182.3 Course sector adjustment ..................................................................................192.3.1 DDM check of ADU O/P ..............................................................................192.3.2 DDM field check...........................................................................................202.4 Monitor combining unit (MCU) adjustments ....................................................... 212.4.1 Course Line ................................................................................................. 212.4.2 Course Sector.............................................................................................. 212.5 Near field monitor adjustments...........................................................................21

2.5.1 Mechanical alignment ..................................................................................212.5.2 Final electrical position adjustment.............................................................. 212.6 DC-Loop adjustment and testing........................................................................212.6.1 DC-LOOP adjustment.................................................................................. 212.6.2 Antenna fault condition testing.....................................................................213 NM 3524 12 Elements antenna system adjustments - LLZ (Dual frequency).....233.1 Mechanical alignment of antenna array .............................................................233.1.1 Right angle points with reference to runway centre line .............................. 233.1.2 Spacing distance between LPDA’s..............................................................233.1.3 Vertical alignment of LPDA support masts ..................................................233.1.4 Azimuth alignment of LPDA’s ......................................................................233.2 Electrical measurements....................................................................................233.2.1 CSB and SBO cables ..................................................................................233.2.2 CSB/SBO phasing .......................................................................................243.2.3 Antenna cable lengths (Electrical phase equality).......................................243.2.4 Antenna pair phasing................................................................................... 253.2.5 Phase and amplitude transfer measurement............................................... 263.2.6 Antenna return loss......................................................................................273.3 Course sector width adjustment......................................................................... 273.3.1 DDM check of ADU O/P ..............................................................................283.3.2 Clearance SBO power ................................................................................. 293.3.3 DDM field check...........................................................................................293.4 Monitor combining unit (MCU) adjustments ....................................................... 293.4.1 Course Line ................................................................................................. 293.4.2 Course Sector.............................................................................................. 293.4.3 Clearance ....................................................................................................293.5 Near field monitor adjustments...........................................................................293.5.1 Mechanical alignment ..................................................................................303.5.2 Final electrical position adjustment.............................................................. 303.6 DC-Loop adjustment and testing........................................................................303.6.1 DC-LOOP adjustment.................................................................................. 303.6.2 Antenna fault condition testing.....................................................................304 NM 3525 24 Elements antenna system adjustments - LLZ...................................314.1 Mechanical alignments of antenna array............................................................314.1.1 Right angle points with reference to runway centre line .............................. 314.1.2 Spacing distance between LPDA’s..............................................................314.1.3 Vertical alignment of LPDA support masts ..................................................314.1.4 Azimuth alignment of LPDA’s ......................................................................314.2 Electrical measurements....................................................................................314.2.1 CSB and SBO cables ..................................................................................314.2.2 CSB/SBO phasing .......................................................................................324.2.3 Antenna cable lengths (Electrical phase equality).......................................324.2.4 Antenna pair phasing................................................................................... 334.2.5 Phase and amplitude transfer measurement............................................... 344.2.6 Antenna return loss......................................................................................354.3 Course sector width adjustments ....................................................................... 354.3.1 DDM check of ADU O/P ..............................................................................354.3.2 Clearance SBO power ................................................................................. 374.3.3 DDM field check...........................................................................................374.4 Monitor combining unit (MCU) adjustments ....................................................... 374.4.1 Course Line ................................................................................................. 374.4.2 Course Sector.............................................................................................. 37

 4.4.3 Clearance ....................................................................................................374.5 Near field monitor adjustments...........................................................................374.5.1 Mechanical alignment ..................................................................................374.5.2 Final electrical position adjustment.............................................................. 384.6 DC-Loop adjustment and testing........................................................................384.6.1 DC-LOOP adjustment.................................................................................. 384.6.2 Antenna fault condition testing.....................................................................385 NM 3526 16 Elements antenna system adjustments - LLZ...................................395.1 Mechanical alignments of antenna array............................................................395.1.1 Right angle points with reference to runway centre line .............................. 395.1.2 Spacing distance between LPDA’s..............................................................395.1.3 Vertical alignment of LPDA support masts ..................................................395.1.4 Azimuth alignment of LPDA’s ......................................................................395.2 Electrical measurements....................................................................................395.2.1 CSB and SBO cables ..................................................................................395.2.2 CSB/SBO phasing .......................................................................................405.2.3 Antenna cable lengths (Electrical phase equality).......................................405.2.4 Antenna pair phasing................................................................................... 415.2.5 Phase and amplitude transfer measurement............................................... 425.2.6 Antenna return loss......................................................................................435.3 Course sector width adjustment......................................................................... 445.3.1 DDM check of ADU O/P ..............................................................................445.3.2 Clearance SBO power ................................................................................. 455.3.3 DDM field check...........................................................................................455.4 Monitor combining unit (MCU) adjustments ....................................................... 455.4.1 Course Line ................................................................................................. 455.4.2 Course Sector.............................................................................................. 455.4.3 Clearance ....................................................................................................465.5 Near field monitor adjustments...........................................................................465.5.1 Mechanical alignment ..................................................................................465.5.2 Final electrical position adjustment.............................................................. 465.6 DC-Loop adjustment and testing........................................................................465.6.1 DC-LOOP adjustment.................................................................................. 465.6.2 Antenna fault condition testing.....................................................................466 NM 3543 Null reference antenna system adjustments - Glide path.....................476.1 Mechanical alignment of mast and antennas.....................................................476.1.1 Preparation of mechanical- and electrical data............................................ 476.1.2 Forward shift (FWD) ....................................................................................476.1.3 Antenna heights...........................................................................................476.1.4 Antenna offsets............................................................................................476.2 Electrical measurements....................................................................................476.2.1 Antenna cable lengths (Electrical phase equality).......................................476.2.2 Monitor return cable length.......................................................................... 486.2.3 Phase and amplitude transfer measurement............................................... 486.2.4 Antenna return loss......................................................................................496.3 CSB/SBO Phasing and sector width adjustment................................................496.3.1 CSB/SBO phasing .......................................................................................496.3.2 Sector Width adjustment.............................................................................. 506.4 Monitoring combining unit (MCU) adjustments .................................................. 516.4.1 Procedure ....................................................................................................516.5 Location of near field antenna position............................................................... 516.5.1 Near Field Monitor Position Search ............................................................. 51

7 NM 3544 Sideband reference antenna system adjustment - Glide path............537.1 Mechanical alignment of mast and antennas.....................................................537.1.1 Preparation of mechanical- and electrical data............................................ 537.1.2 Forward shift (FWD) ....................................................................................537.1.3 Antenna heights...........................................................................................537.1.4 Antenna offsets............................................................................................537.2 Initial electrical measurements........................................................................... 537.2.1 Antenna cable lengths (Electrical phase equality).......................................537.2.2 Monitor return cable length.......................................................................... 547.2.3 Phase and amplitude transfer measurement............................................... 547.2.4 Antenna return loss......................................................................................557.3 CSB/SBO Phasing .............................................................................................557.3.1 CSB and SBO cables ..................................................................................557.3.2 CSB/SBO phasing .......................................................................................567.4 Sector width adjustment.....................................................................................567.4.1 SBO power adjustment................................................................................567.5 Monitor combining unit (MCU) adjustments ....................................................... 567.5.1 Procedure for horizontal terrain (FSL = 0°).................................................. 567.5.2 Procedure for sloping terrain (1° > FSL > -1°) .............................................567.6 Location of near field antenna position............................................................... 577.6.1 Near Field Monitor Position Search ............................................................. 587.7 Antenna distribution unit (ADU) phase and amplitude check.............................597.7.1 Preparation ..................................................................................................597.7.2 Procedure ....................................................................................................598 NM 3545 M-Array antenna system adjustments - Glide path ...............................618.1 Mechanical alignment of mast and antennas.....................................................618.1.1 Preparation of mechanical- and electrical data............................................ 618.1.2 Forward shift (FWD) ....................................................................................618.1.3 Antenna heights...........................................................................................618.1.4 Antenna offsets............................................................................................618.2 Initial electrical measurements........................................................................... 618.2.1 Antenna cable lengths (Electrical phase equality).......................................618.2.2 Monitor return cable length.......................................................................... 628.2.3 Phase and amplitude transfer measurement............................................... 628.2.4 Antenna return loss......................................................................................638.3 CSB/SBO Phasing .............................................................................................638.3.1 CSB and SBO cables ..................................................................................638.3.2 CSB/SBO phasing .......................................................................................638.4 Sector width adjustment.....................................................................................648.4.1 SBO power adjustment................................................................................648.5 Monitor combining unit (MCU) MOA 338D adjustments ....................................648.5.1 Adjustments procedure................................................................................ 658.6 Location of near field antenna position............................................................... 658.6.1 Near Field Monitor Position Search ............................................................. 658.7 Antenna distribution unit (ADU) DIA 346A phase and amplitude check.............668.7.1 Preparation ..................................................................................................668.7.2 Procedure ....................................................................................................679 NM 3561 Single antenna system adjustments - MKR............................................699.1 Mechanical alignment.........................................................................................699.1.1 Antenna mast............................................................................................... 699.2 Electrical measurements....................................................................................699.2.1 Antenna return loss......................................................................................69

 10 NM 3562 Dual antenna system adjustments - MKR...............................................7110.1 Mechanical alignment.........................................................................................7110.1.1Antenna mast...............................................................................................7110.2 Electrical measurements.................................................................................... 7110.2.1Antenna cable lengths (Electrical phase equality)....................................... 7110.2.2Monitor return cable length..........................................................................7210.2.3Phase and amplitude transfer measurement...............................................72

 1 NM 3522 6 elements antenna system adjustments - LLZ1.1 Mechanical alignment of antenna array1.1.1 Right angle points with reference to runway center lineThe alignment of the antenna array perpendicular to the runway centreline should be carried out to an accuracy of 0.03°.This corresponds to within 4 mm accuracy at positions antenna 1 and antenna 6. A theodolite should be utilised.1.1.2 Spacing distance between LPDA’sCheck that the spacing between each LPDA is according to dimensions given in dwg.no. 7106A3.Tolerance: ±5 mm.1.1.3 Vertical alignment of LPDA support mastsOn each rear support mast for LPDA check with waterlevel that mast is vertically aligned in both planes.1.1.4 Azimuth alignment of LPDA’sDetermine a fixed point as far as possible along the extended centreline not less than approx-imately 3000 m from the antenna array.On each LPDA utilise the top horizontal line composed of the two half sections of the radome to point toward the fixed point.If necessary adjust the LPDA horizontally by adjusting the mast supports on the front mast, so that the extended radome top line ends at the fixed point.1.2 Electrical measurements1.2.1 CSB and SBO cablesThe CSB and SBO cable between the cabinet and MCU must be of equal electrical length. Utilise a vector voltmeter or network analyser in a test set-up as in Figure 1-1.Measure open cable return phase for each cable.Refer to CSB cable as zero phase and measure the return phase for the SBO cable. The cable pair must be matched within ±3.0° return phase, equal to ±1.5° true phase

$.Figure 1-1 Cable phasing measurements set-up.1.2.2 CSB/SBO phasing127($VFHUWDLQWKDWWKH7[PRGXODWRUXVHGLVRSWLPDOO\FDOLEUDWHGConnect the NM3710 Field Test Set to the monitor BNC test connector in the ADU. (Use 20..30 dB attenuator at the I/P of the Field Test Set.)Adjust SBO phaser in the Cabinet (associated with Tx to air) to obtain 0.0% DDM reading.Repeat the phasing procedure for the other transmitter.1.2.3 Antenna cable lengths (Electrical phase equality)Each antenna cable should be electrically checked before the end connector is terminated in the LPDA.Utilise a vector voltmeter or network analyser. Establish antenna cable (A1) (leftmost seen from rear) return phase as 0° reference phase.Measure return phase for each of the remaining antenna cables (A2...A6).Tolerance: ±1.0° true electrical cable length. See measurement set-up diagram Figure 1-1.1.2.4 Antenna pair phasing127(%HIRUHWKHDQWHQQDSDLUSKDVLQJSURFHGXUHLVFRPPHQFHGDVFHUWDLQWKDWWKH7[PRGXODWRUXVHGLVRSWLPDOO\FDOLEUDWHG20dBABVECTOR VOLTMETERFrom cabinetCSB BNC o/pCABLE UNDER TESTOPEN ENDDIR. COUPL.$

  Connect the antenna cables A1 and A6 to the ADU outputs labelled A1 and A6 respectively.Connect all other ADU outputs to dummy load. Use the NM3710 with portable test antenna.On the the runway establish a point officially marked as the centre line for DDM measure-ments. Ascertain that the measurement point is not affected by reflected signals degrading the direct received signals from the antenna pairs. This can be tested by moving the test antenna a few meters back and fourth while observing the DDM reading. If the value is not changing significantly then the measurement position is OK.Take a note of the DDM reading first from antenna pair A1/A6.Connect pair A2/A5 to ADU outputs A2/A5 and disconnect pair A1/A6, dummyload A1/A6 ADU.Take a note of the DDM reading.Carry out this procedure until all antenna pairs DDM readings have been noted.If any antenna pair measures DDM different from zero, one of the antenna pair feed cable lengths should be trimmed in order to bring the DDM reading to zero.If the DDM reading is positive (150 Hz dominance) the antenna cable at the right hand side (A4...A6) should be trimmed.The sensitivity of DDM versus electrical phase error of 2° (5° CS) is given in the table below:The sensitivity of DDM versus electrical phase error can be estimated using the following pro-cedure:1. Note the DDM value reported by the operator at the Field Test Set for the antenna pair under test. 2. a) If the DDM value is positive (150 Hz dominance), insert a male-female (MF) N-adaptor (-9°) in the antenna left side seen forward toward the Field test set. b) If the DDM value is negative (90 Hz dominance), insert a male-female (MF) N-adaptor (-9°) in the antenna right side seen forward toward the Field test set.3. Note the new DDM value. (This value should have oposite polarity compared to the value without the adaptor.)4. Calculate the corresponding phase error (electrical degrees) from the formula : DDM1 (%) measured in item 1. : DDM3 (%) measured in item 3.(Example values from NM3523B)ϕ°() 9°DDM1DDM1DDM3+-------------------------------------------=

Example 1:Item 1: A1/A12: +4.3% DDMItem 3: A1+MF/A12: -2.0% DDM (MF in A1) Example 2:Item 1: A6/A7: -0.6% DDMItem 3: A6 /A7+MF: +1.86% DDM (MF in A7)Cable trimming length: 6.2 mm/°.1.2.5 Phase and amplitude transfer measurementConnect each antenna cable and monitor cable to LPDA load and source respectively. Utilise a vector voltmeter or network analyser in a test set-upFigure 1-2 Phase and amplitude transfer measurement set-up.Measure relative transfer phase and amplitude for each Antenna/Monitor return cable in ref-erence to A1/M1.Then determine if one or more of the monitor cables must be trimmed in order to comply with phase tolerance for the set of cables.Tolerance: ±2°.ϕ9°4.3⋅4.3 2.0+---------------------4.8°==ϕ9°0.6⋅0.6 1.86+------------------------1.7°==20dBABVECTOR VOLTMETERA(n)M(n)From cabinetCSB BNC o/pLPDADIR. COUPL.

 Amplitude tolerance: ±1.0 dB. If the amplitude tolerance is exceeded something might be wrong in the LPDA monitor circuit or connector/cable.Record the final result in Ground Commissioning Record.1.2.6 Antenna return lossUtilise a vector voltmeter or network analyser in a test set-up Figure 1-3. Measure return loss for each LPDA.Measure and record in Ground Commissioning Record the return loss value for each LPDA including antenna cable.Tolerance: 20 dB minimum.Figure 1-3 Antenna return loss measurement set-up.1.3 Course sector width adjustmentThe required course sector width (CS) can be pre-adjusted by two methods:1. DDM measurement of ADU antenna feed outputs.2. DDM field check.Preferably both methods should be carried out and compared.20dBABVECTOR VOLTMETERFrom cabinetCSB BNC o/pDIR. COUPL.Antenna cable under testAntenna

1.3.1 DDM check of ADU O/P (output port)At each antenna feed output of the ADU the measured DDM is a result of the SBO/CSB ratio according to the formulawhereCSB is a fixed value.SBO is adjustable by the SBO attenuator in the cabinet.γ is 0° when the 90°-stub is inserted into the SBO.For each course sector width (CS) of the array a set of corresponding DDM values exists unique for each antenna O/P.For CS = 5°:For other CS values use the formula:ExampleA3 DDM for CS = 5.4°:PROCEDUREInsert the 90°-stub into the SBO path.Connect a directional coupler with 50* load to antenna O/P A3.Connect the NM3710 (use 20 dB attenuator at NM3710 I/P) to the directional coupler's for-ward port.Adjust the SBO attenuator (for the Tx to air) until the DDM value equals the previously calcu-lated value for the CS.%DDM µA %SDMA2 -34.8 -337 40.0A3 -32.7 -316 40.0DDM 2SBO⋅CSB-------------------COSγ=DDMAn()DDM 5°()5°⋅CS---------------------------------=DDMA332.7 5⋅–5.4---------------------29.5%==

 Move the directional coupler to A4 and compare readings with calculated value. If measured DDM is lower than the calculated values for A4 then increase the SBO power, or vice versa, until a fairly good matching set of values are obtained.Adjust the SBO attenuator for the other Tx to the same setting.Remove the 90°-stub1.3.2 DDM field checkSet the localizer to normal radiation. From the centreline of the opposite threshold determine points perpendicular to the CL 105 meter to both sides of the runway. Use the NM3710 with portable antenna and measure DDM at these points. The readings should be close to -15.5% at the 90-side and 15.5% at the 150-side. However, some unsymmetry may be expected due to reflections and tolerances in the antenna system.Check the CL DDM at two or three positions in order to estimate an average value.Expected value: 0.0%±0.2% DDM.1.4 Monitor combining unit (MCU) adjustments1.4.1 Course LineConnect the Field Test Set to the CL output connector of the MCU.Adjust the CL line stretcher to obtain 0.0% DDM.1.4.2 Course SectorConnect the Field Test Set to the CS output of the MCU.Adjust the CS line stretcher to obtain a reading of 15.5% DDM.1.5 Near field monitor adjustmentsThe exact position of the near field monitor antenna cannot be determined until after the flight check is completed, due to possible mechanical re-alignment of the antenna array.1.5.1 Mechanical alignmentAlign the near field (NF) monitor antenna mechanically in the extended runway centreline position.1.5.2 Final electrical position adjustmentConnect the Field Test Set to the NF monitor cable. The reading should be 0.0% DDM if the antenna is aligned correctly and no reflections appear.Otherwise, a small mechanical re-positioning of the antenna may be necessary in order to obtain 0.0% DDM.

1.6 DC-Loop adjustment and testing1.6.1 DC-LOOP adjustmentThe DC loop (cable fault monitor) alignment is carried out accordingly to the procedure described in Monitor Alignment and Calibration chapter.1.6.2 Antenna fault condition testingFor this test observe that the LLZ cabinet System Status indicates ALARM.The transmitter must be on during this test.The monitors should be in MANUAL mode in order to prevent transmitter from being shut off during the test.Disconnect one antenna at a time and check that the LLZ cabinet System Status indicates ALARM after each antenna disconnection.Carry out this test for all antennas.

 2 NM 3523B 12 Elements antenna system adjustments - LLZ (Single fre-quency)2.1 Mechanical alignments of antenna array2.1.1 Right angle points with reference to runway centre lineThe alignment of the antenna array perpendicular to the runway centreline should be carried out to an accuracy of 0.02°.This corresponds to within 5 mm accuracy at positions antenna 1 and antenna 12. A theodo-lite should be utilised.2.1.2 Spacing distance between LPDA’sCheck that the spacing between each LPDA is according to dimensions given in dwg.no. 8151A3.Tolerance: ±5 mm.2.1.3 Vertical alignment of LPDA support mastsOn each rear support mast for LPDA check with waterlevel that mast is vertically aligned in both planes.2.1.4 Azimuth alignment of LPDA’sDetermine a fixed point as far as possible along the extended centreline not less than approx-imately 3000 m from the antenna array.On each LPDA utilise the top horizontal line composed of the two half sections of the radome to point toward the fixed point.If necessary adjust the LPDA horizontally by adjusting the mast supports on the front mast, so that the extended radome top line ends at the fixed point.2.2 Electrical measurements2.2.1 CSB and SBO cablesThe CSB and SBO cable between the cabinet and MCU must be of equal electrical length. Utilise a vector voltmeter or network analyser in a test set-up as in Figure 2-1.Measure open cable return phase for each cable.Refer to CSB cable as zero phase and measure the return phase for the SBO cable. The cable pair must be matched within ±3.0° return phase, equal to ±1.5° true phase

$.Figure 2-1 Cable phasing measurement set-up.2.2.2 CSB/SBO phasing127($VFHUWDLQWKDWWKH7[PRGXODWRUXVHGLVRSWLPDOO\FDOLEUDWHGConnect the NM3710 Field Test Set to the monitor BNC test connector in the ADU. (Use 20..30 dB attenuator at the I/P of the Field Test Set.)Adjust SBO phaser in the Cabinet (associated with Tx to air) to obtain 0.0% DDM reading.Repeat the phasing procedure for the other transmitter.2.2.3 Antenna cable lengths (Electrical phase equality)Each antenna cable should be electrically checked before the end connector is terminated in the LPDA.Utilise a vector voltmeter or network analyser. Establish antenna cable (A1) (leftmost seen from rear) return phase as 0° reference phase.Measure return phase for each of the remaining antenna cables (A2...A12).Tolerance: ±1.0° true electrical cable length. See measurement set-up diagram 2-1.2.2.4 Antenna pair phasing127(%HIRUHWKHDQWHQQDSDLUSKDVLQJSURFHGXUHLVFRPPHQFHGDVFHUWDLQWKDWWKH7[PRGXODWRUXVHGLVRSWLPDOO\FDOLEUDWHGConnect the antenna cables A1 and A12 to the ADU outputs labelled A1 and A12 respec-tively.20dBABVECTORFrom cabinetCSB BNC o/pCABLE UNDER TESTOPEN ENDDIR. COUPL.$

 Connect all other ADU outputs to dummy load. Use the NM3710 with portable test antenna.On the the runway establish a point officially marked as the centre line for DDM measure-ments. Ascertain that the measurement point is not affected by reflected signals upsetting the direct received signals from the antenna pairs. This can be tested by moving the test antenna a few meters back and fourth while observing the DDM reading. If the value is not changing then the measurement position is OK.Take a note of the DDM reading first from antenna pair A1/A12.Connect pair A2/A11 to ADU outputs A2/A11 and disconnect pair A1/A12, dummyload A1/A12 ADU.Take a note of the DDM reading.Carry out this procedure until all antenna pairs DDM readings have been noted.If any antenna pair measures DDM different from zero, one of the antenna pair feed cable lengths should be trimmed in order to bring the DDM reading to zero.If the DDM reading is positive (150 Hz dominance) the antenna cable at the right hand side (A7...A12) should be trimmed.The sensitivity of DDM versus electrical phase error can be estimated using the following pro-cedure:1. Note the DDM value reported by the operator at the Field Test Set for the antenna pair under test. 2. a) If the DDM value is positive (150 Hz dominance), insert a male-female (MF) N-adaptor (-9°) in the antenna left side seen forward toward the Field test set.b) If the DDM value is negative (90 Hz dominance), insert a male-female (MF) N-adaptor (-9°) in the antenna right side seen forward toward the Field test set.3. Note the new DDM value. (This value should have oposite polarity compared to the value without the adaptor.)4. Calculate the corresponding phase error (electrical degrees) from the formula DDM1: DDM(%) measured in item 1.DDM3: DDM(%) measured in item 3.(Example values from NM3523B)Example 1:Item 1: A1/A12: +4.3% DDMItem 3: A1+MF/A12: -2.0% DDM (MF in A1)ϕ°() 9°DDM1DDM1DDM3+-------------------------------------------=

Example 2:Item 1: A6/A7: -0.6% DDMItem 3: A6 /A7+MF: +1.86% DDM (MF in A7)Cable trimming length: 6.2 mm/°.2.2.5 Phase and amplitude transfer measurementConnect each antenna cable and monitor cable to LPDA load and source respectively. Utilise a vector voltmeter or network analyser in a test set-up Figure 2-2Figure 2-2 Phase and amplitude transfer measurement set-up.Measure relative transfer phase and amplitude for each Antenna/Monitor return cable in ref-erence to A1/M1.Then determine if one of the monitor cables must be trimmed in order to comply with phase tolerance for the set of cables.Tolerance: ±2°.Amplitude tolerance: ±1.0 dB. If the amplitude tolerance is exceeded something might be wrong in the LPDA monitor circuit or connector/cable.Record the final result in Ground Commissioning Record.2.2.6 Antenna return lossUtilise a vector voltmeter or network analyser in a test set-up Figure 2-3. Measure return loss for each LPDA.ϕ9°4.3⋅4.3 2.0+---------------------4.8°==ϕ9°0.6⋅0.6 1.86+------------------------1.7°==20dBABVECTOR VOLTMETERA(n)M(n)From cabinetCSB BNC o/pLPDADIR. COUPL.

 Measure and record in Ground Commissioning Record the return loss value for each LPDA including antenna cable.Tolerance: 20 dB minimum.Figure 2-3 Antenna return loss measurement set-up.2.3 Course sector adjustmentThe required course sector width (CS) can be pre-adjusted by two methods:1. DDM measurement of ADU antenna feed outputs.2. DDM field check.Preferably both methods should be carried out and compared.2.3.1 DDM check of ADU O/PAt each antenna feed output of the ADU the measured DDM is a result of the SBO/CSB ratio according to the formulawhereCSB is a fixed value.SBO is adjustable by the SBO attenuator in the cabinet.γ is 0° when the 90°-stub is inserted into the SBO.For each course sector width (CS) of the array a set of corresponding DDM values exists unique for each antenna O/P.20dBABVECTOR VOLTMETERFrom cabinetCSB BNC o/pDIR. COUPL.Antenna cable under testAntennaDMM 2SBO⋅CSB-------------------COSγ=

For CS = 4°:For other CS values use the formula:EXAMPLEA5 DDM for CS = 5°:PROCEDUREInsert the 90°-stub into the SBO path.Connect a directional coupler with 50Ω load to antenna O/P A3.Connect the NM3710 (use 20 dB attenuator at NM3710 I/P) to the directional coupler's for-ward port.Adjust the SBO attenuator (for the Tx to air) until the DDM value equals the previously calcu-lated value for the CS.Move the directional coupler to A4, A5, A6 and compare readings with calculated values. If measured DDM is lower than the calculated values for A4, A5, A6 then increase the SBO power, or vice versa, until a fairly good matching set of values are obtained.Adjust the SBO attenuator for the other Tx to the same setting.Remove the 90°-stub.2.3.2 DDM field checkSet the localizer to normal radiation. From the centreline of the opposite threshold determine points perpendicular to the CL 105 meter to both sides of the runway. Use the NM3710 with portable antenna and measure DDM at these points. The readings should be close to -15.5% at the 90-side and 15.5% at the 150-side. However, some unsymmetry may be expected due to reflections and tolerances in the antenna system.Check the CL DDM at two or three positions in order to estimate an average value.Expected value: 0.0%±0.2% DDM.% DDM µA %SDMA2 -34.8 -337 40.0A3 -32.7 -316 40.0A5 -28.1 -272 40.0A6 -30.4 -294 40.0DDMAn()DDM 4°()4°⋅CS---------------------------------=DMA328.1 4⋅–5---------------------22.5%–==

 2.4 Monitor combining unit (MCU) adjustments2.4.1 Course LineConnect the Field Test Set to the CL output connector of the MCU.Adjust the CL line stretcher to obtain 0.0% DDM.2.4.2 Course SectorConnect the Field Test Set to the CS output of the MCU.Adjust the CS line stretcher to obtain a reading of 15.5% DDM.2.5 Near field monitor adjustmentsThe exact position of the near field monitor antenna cannot be determined until after the flight check is completed, due to possible mechanical re-alignment of the antenna array.2.5.1 Mechanical alignmentAlign the near field (NF) monitor antenna mechanically in the extended runway centreline position.2.5.2 Final electrical position adjustmentConnect the Field Test Set to the NF monitor cable. The reading should be 0.0% DDM if the antenna is aligned correctly and no reflections appear.Otherwise, a small mechanical re-positioning of the antenna may be necessary in order to obtain 0.0% DDM.2.6 DC-Loop adjustment and testing2.6.1 DC-LOOP adjustmentThe DC loop (cable fault monitor) alignment is carried out accordingly to the procedure described in Monitor Alignment and Calibration chapter.2.6.2 Antenna fault condition testingFor this test observe that the LLZ cabinet System Status indicates ALARM.The transmitter must be on during this test.The monitors should be in MANUAL mode in order to prevent transmitter from being shut off during the test.Disconnect one antenna at a time and check that the LLZ cabinet System Status indicates ALARM after each antenna disconnection.Carry out this test for all antennas.

 3 NM 3524 12 Elements antenna system adjustments - LLZ (Dual fre-quency)3.1 Mechanical alignment of antenna array3.1.1 Right angle points with reference to runway centre lineThe alignment of the antenna array perpendicular to the runway centreline should be carried out to an accuracy of 0.02°.This corresponds to within 4 mm accuracy at positions antenna 1 and antenna 12. A theodo-lite should be utilised.3.1.2 Spacing distance between LPDA’sCheck that the spacing between each LPDA is 2.04 m.Tolerance: ±5 mm.3.1.3 Vertical alignment of LPDA support mastsOn each rear support mast for LPDA check with waterlevel that mast is vertically aligned in both planes.3.1.4 Azimuth alignment of LPDA’sDetermine a fixed point as far as possible along the extended centreline not less than approx-imately 3000 m from the antenna array.On each LPDA utilise the top horizontal line composed of the two half sections of the radome to point toward the fixed point.If necessary adjust the LPDA horizontally by adjusting the mast supports on the front mast, so that the extended radome top line ends at the fixed point.3.2 Electrical measurements3.2.1 CSB and SBO cablesCourse Tx cables.The CSB and SBO cable between the cabinet and MCU must be of equal electrical length. Utilise a vector voltmeter or network analyser in a test set-up as in Figure 3-1.Measure open cable return phase for each cable.Refer to CSB cable as zero phase and measure the return phase for the SBO cable. The cable pair must be matched within ±3.0° return phase, equal to ±1.5° true phase.Clearance Tx cables.Repeat the procedure 3.2.1 for CLR Tx CSB and SBO cables

$.Figure 3-1 Cable phasing measurement set-up.3.2.2 CSB/SBO phasing127(6ZLWFKRIIWKHFOHDUDQFHWUDQVPLWWHU$VFHUWDLQWKDWWKH7[PRGXODWRUXVHGLVRSWLPDOO\FDOLEUDWHGConnect the NM3710 Field Test Set to the monitor BNC test connector in the ADU. (Use 20..30 dB attenuator at the I/P of the Field Test Set.)Adjust Course SBO phaser in the Cabinet (associated with Tx to air) to obtain 0.0% DDM reading.Repeat the phasing procedure for the other transmitter.Switch off the course transmitter.With the clearance transmitter on repeat the phasing procedure now adjusting the clearance SBO phaser associated with Tx to air. 3.2.3 Antenna cable lengths (Electrical phase equality)Each antenna cable should be electrically checked before the end connector is terminated in the LPDA.Utilise a vector voltmeter or network analyser. Establish antenna cable (A1) (leftmost seen from rear) return phase as 0° reference phase.Measure return phase for each of the remaining antenna cables (A2...A12).Tolerance: ±1.0° true electrical cable length. See measurement set-up diagram Figure 3-1.20dBABVECTORFrom cabinetCSB BNC o/pCABLE UNDER TESTOPEN ENDDIR. COUPL.$

$ 3.2.4 Antenna pair phasing127(%HIRUHWKHDQWHQQDSDLUSKDVLQJSURFHGXUHLVFRPPHQFHGDVFHUWDLQWKDWWKH7;PRGXODWRUXVHGLVRSWLPDOO\FDOLEUDWHG6ZLWFKRIIWKHFOHDUDQFHWUDQVPLWWHUConnect the antenna cables A1 and A12 to the ADU outputs labelled A1 and A12 respec-tively.Connect all other ADU outputs to dummy load. Use the NM3710 with portable test antenna.On the the runway establish a point officially marked as the centre line for DDM measure-ments. Ascertain that the measurement point is not affected by reflected signals upsetting the direct received signals from the antenna pairs. This can be tested by moving the test antenna a few meters back and fourth while observing the DDM reading. If the value is not changing then the measurement position is OK.Take a note of the DDM reading first from antenna pair A1/A12.Connect pair A2/A11 to ADU outputs A2/A11 and disconnect pair A1/A12, dummyload A1/A12 ADU.Take a note of the DDM reading.Carry out this procedure until all antenna pairs DDM readings have been noted.If any antenna pair measures DDM different from zero, one of the antenna pair feed cable lengths should be trimmed in order to bring the DDM reading to zero.If the DDM reading is positive (150 Hz dominance) the antenna cable at the right hand side (A7...A12) should be trimmed.The sensitivity of DDM versus electrical phase error of 2° (4° CS) is given in the table below:Cable trimming length: 6.2 mm/°.The sensitivity of DDM versus electrical phase error can be estimated using the following pro-cedure:Note the DDM value reported by the operator at the Field Test Set for the antenna pair under test. a) If the DDM value is positive (150 Hz dominance), insert a male-female (MF) N-adaptor (-9°) in the antenna left side seen forward toward the Field test set.b) If the DDM value is negative (90 Hz dominance), insert a male-female (MF) N-adaptor (-9°) in the antenna right side seen forward toward the Field test set.Note the new DDM value. (This value should have oposite polarity compared to the value without the adaptor.)$

Calculate the corresponding phase error (electrical degrees) from the formula : DDM (%) measured in item 1. : DDM (%) measured in item 3.(Example values from NM3523B)Example 1:Item 1: A1/A12: +4.3% DDMItem 3: A1+MF/A12: -2.0% DDM (MF in A1)Example 2:Item 1: A6/A7: -0.6% DDMItem 3: A6 /A7+MF: +1.86% DDM (MF in A7)3.2.5 Phase and amplitude transfer measurementConnect each antenna cable and monitor cable to LPDA load and source respectively. Utilise a vector voltmeter or network analyser in a test set-up Figure 3-2.Figure 3-2 Phase and amplitude transfer measurement set-up.Measure relative transfer phase and amplitude for each Antenna/Monitor return cable in ref-erence to A1/M1.ϕ°() 9°DDM1DDM1DDM3+-------------------------------------------=ϕ9°4.3⋅4.3 2.0+---------------------4.8°==ϕ9°0.6⋅0.6 1.86+------------------------1.7°==20dBABVECTOR VOLTMETERA(n)M(n)From cabinetCSB BNC o/pAnt.DIR. COUPL.

 Then determine if one of the monitor cables must be trimmed in order to comply with phase tolerance for the set of cables.Tolerance: ±2°.Amplitude tolerance: ±1.0 dB. If the amplitude tolerance is exceeded something might be wrong in the LPDA monitor circuit or connector/cable.Record the final result in Ground Commissioning Record.3.2.6 Antenna return lossUtilise a vector voltmeter or network analyser in a test set-up Figure 3-3. Measure return loss for each LPDA.Measure and record in Ground Commissioning Record the return loss value for each LPDA including antenna cable.Tolerance: 20 dB minimum.Figure 3-3 Antenna return loss measurement set-up.3.3 Course sector width adjustmentThe required course sector width (CS) can be pre-adjusted by two methods:1. DDM measurement of ADU antenna feed outputs.2. DDM field check.Preferably both methods should be carried out and compared.20dBABVECTOR VOLTMETERFrom cabinetCSB BNC o/pDIR. COUPL.Antenna cable under testAntenna

3.3.1 DDM check of ADU O/PAt each antenna feed output of the ADU the measured DDM is a result of the SBO/CSB ratio according to the formulawhereCSB is a fixed value.SBO is adjustable by the SBO attenuator in the cabinet.γ is 0° when the 90°-stub is inserted into the SBO.For each course sector width (CS) of the array a set of corresponding DDM values exists unique for each antenna O/P.For CS = 4°:For other CS values use the formula:ExampleA3 DDM for CS = 5°:PROCEDURETurn off the clearance transmitter. Insert the 90°-stub into the course SBO path. Connect a directional coupler with 50Ω load to antenna O/P A3.Connect the NM3710 (use 20 dB attenuator at NM3710 I/P) to the directional coupler's for-ward port.Adjust the SBO attenuator (for the Tx to air) until the DDM value equals the previously calcu-lated value for the CS.Move the directional coupler to A4, A5 and compare readings with calculated values. If mea-sured DDM is lower than the calculated values for A4, A5 then increase the SBO power, or vice versa, until a fairly good matching set of values are obtained.% DDM µA %SDMA3 -40.0 -387 53.8A4 -38.3 -371 40.0A5 -22.9 -222 40.0DDMAn()DDM 4°()4°⋅CS---------------------------------=DDMA353.8 4⋅–5---------------------43.0%==

 Adjust the SBO attenuator for the other Tx to the same setting.Remove the 90°-stub.3.3.2 Clearance SBO powerSwitch off the course transmitter.Insert the 90°-stub in the CLR SBO path. Connect the Field Test Set to the BNC test connec-tor (antenna 7 sample) in the ADU. (Use 20...30 dB attenuator at the Field Test Set I/P).Switch on the clearance transmitter. Adjust the CLR SBO attenuator in the cabinet (associ-ated with Tx to air) until a reading of 36% DDM is obtained.Carry out the same procedure for the other transmitter.3.3.3 DDM field checkSet the localizer to normal radiation (clearance transmitter on). From the centreline of the opposite threshold determine points perpendicular to the CL 105 meter to both sides of the runway. Use the NM3710 with portable antenna and measure DDM at these points. The read-ings should be close to -15.5% at the 90-side and 15.5% at the 150-side. However, some unsymmetry may be expected due to reflections and tolerances in the antenna system.Check the CL DDM at two or three positions in order to estimate an average value. Expected value: 0.0%±0.2% DDM.3.4 Monitor combining unit (MCU) adjustments3.4.1 Course LineConnect the Field Test Set to the CL output connector of the MCU.Adjust the CL line stretcher to obtain 0.0% DDM.3.4.2 Course SectorConnect the Field Test Set to the CS output of the MCU.Adjust the CS line stretcher to obtain a reading of 15.5% DDM.3.4.3 ClearanceConnect the Field Test Set to the CLR output connector of the MCU. Adjust the CLR line stretcher to obtain a reading of 27% DDM.3.5 Near field monitor adjustmentsThe exact position of the near field monitor antenna cannot be determined until after the flight check is completed, due to possible mechanical re-alignment of the antenna array.

3.5.1 Mechanical alignmentAlign the near field (NF) monitor antenna mechanically in the extended runway centreline position.3.5.2 Final electrical position adjustmentConnect the Field Test Set to the NF monitor cable. The reading should be 0.0% DDM if the antenna is aligned correctly and no reflections appear.Otherwise, a small mechanical re-positioning of the antenna may be necessary in order to obtain 0.0% DDM.3.6 DC-Loop adjustment and testing3.6.1 DC-LOOP adjustmentThe DC loop (cable fault monitor) alignment is carried out accordingly to the procedure described in Monitor Alignment and Calibration chapter.3.6.2 Antenna fault condition testingFor this test observe that the LLZ cabinet System Status indicates ALARM.The transmitter must be on during this test.The monitors should be in MANUAL mode in order to prevent transmitter from being shut off during the test.Disconnect one antenna at a time and check that the LLZ cabinet System Status indicates ALARM after each antenna disconnection.Carry out this test for all antennas.

 4 NM 3525 24 Elements antenna system adjustments - LLZ4.1 Mechanical alignments of antenna array4.1.1 Right angle points with reference to runway centre lineThe alignment of the antenna array perpendicular to the runway centreline should be carried out to an accuracy of 0.01°.This corresponds to within 5 mm accuracy at positions antenna 1 and antenna 24. A theodo-lite should be utilised.4.1.2 Spacing distance between LPDA’sCheck that the spacing between each LPDA is 2.04 m.Tolerance: ±5 mm.4.1.3 Vertical alignment of LPDA support mastsOn each rear support mast for LPDA check with waterlevel that mast is vertically aligned in both planes.4.1.4 Azimuth alignment of LPDA’sDetermine a fixed point as far as possible along the extended centreline not less than approx-imately 3000 m from the antenna array.On each LPDA utilise the top horizontal line composed of the two half sections of the radome to point toward the fixed point.If necessary adjust the LPDA horizontally by adjusting the mast supports on the front mast, so that the extended radome top line ends at the fixed point.4.2 Electrical measurements4.2.1 CSB and SBO cablesCourse Tx cables.The CSB and SBO cable between the cabinet and MCU must be of equal electrical length. Utilise a vector voltmeter or network analyser in a test set-up as in Figure 4-1.Measure open cable return phase for each cable.Refer to CSB cable as zero phase and measure the return phase for the SBO cable. The cable pair must be matched within ±3.0° return phase, equal to ±1.5° true phase.Clearance Tx cables.Repeat the procedure 1.2.1 for CLR Tx CSB and SBO cables

$.Figure 4-1 Cable phasing measurement set-up.4.2.2 CSB/SBO phasing127(6ZLWFKRIIWKHFOHDUDQFHWUDQVPLWWHU$VFHUWDLQWKDWWKH7[PRGXODWRUXVHGLVRSWLPDOO\FDOLEUDWHGConnect the NM3710 Field Test Set to the monitor BNC test connector in the ADU. (Use 20..30 dB attenuator at the I/P of the Field Test Set.)Adjust SBO phaser in the Cabinet (associated with Tx to air) to obtain 0.0% DDM reading.Repeat the phasing procedure for the other transmitter.Switch off the course transmitter.With the clearance transmitter on repeat the phasing procedure now adjusting the clearance SBO phaser associated with Tx to air. 4.2.3 Antenna cable lengths (Electrical phase equality)Each antenna cable should be electrically checked before the end connector is terminated in the LPDA.Utilise a vector voltmeter or network analyser. Establish antenna cable (A1) (leftmost seen from rear) return phase as 0° reference phase.Measure return phase for each of the remaining antenna cables (A2...A24).Tolerance: ±1.0° true electrical cable length. See measurement set-up diagram Figure 4-120dBABVECTOR VOLTMETERFrom cabinetCSB BNC o/pCABLE UNDER TESTOPEN ENDDIR. COUPL.$

$ 4.2.4 Antenna pair phasing127(%HIRUHWKHDQWHQQDSDLUSKDVLQJSURFHGXUHLVFRPPHQFHGDVFHUWDLQWKDWWKH7[PRGXODWRUXVHGLVRSWLPDOO\FDOLEUDWHG6ZLWFKRIIWKHFOHDUDQFHWUDQVPLWWHUConnect the antenna cables A1 and A24 to the ADU outputs labelled A1 and A24 respec-tively.Connect all other ADU outputs to dummy load. Use the NM3710 with portable test antenna.On the the runway establish a point officially marked as the centre line for DDM measure-ments. Ascertain that the measurement point is not affected by reflected signals upsetting the direct received signals from the antenna pairs. This can be tested by moving the test antenna a few meters back and fourth while observing the DDM reading. If the value is not changing then the measurement position is OK.Take a note of the DDM reading first from antenna pair A1/A24.Connect pair A2/A23 to ADU outputs A2/A23 and disconnect pair A1/A24, dummyload A1/A24 ADU.Take a note of the DDM reading.Carry out this procedure until all antenna pairs DDM readings have been noted.If any antenna pair measures DDM different from zero, one of the antenna pair feed cable lengths should be trimmed in order to bring the DDM reading to zero.If the DDM reading is positive (150 Hz dominance) the antenna cable at the right hand side (A13...A24) should be trimmed.The sensitivity of DDM versus electrical phase error of 6° (4° CS) is given in the table below:$

Cable trimming length: 6.2 mm/°.4.2.5 Phase and amplitude transfer measurementConnect each antenna cable and monitor cable to LPDA load and source respectively. Utilise a vector voltmeter or network analyser in a test set-up Figure 4-2.Figure 4-2 Phase and amplitude transfer measurement set-up.Measure relative transfer phase and amplitude for each Antenna/Monitor return cable in ref-erence to A1/M1.Pair µA DDM (6°) % DDM (6°)A1/A24 20.1 2.08A2/A23 18.5 1.91A3/A22 16.8 1.74A4/A21 14.9 1.54A5/A20 13.2 1.36A6/A19 11.4 1.18A7/A18 9.7 1.00A8/A17 7.9 0.82A9/A16 6.2 0.64A10/A15 4.4 0.45A11/A14 2.6 0.27A12/A13 0.9 0.0920dBABVECTOR VOLTMETERA(n)M(n)From cabinetCSB BNC o/pLPDADIR. COUPL.

whereCSB is a fixed value.SBO is adjustable by the SBO attenuator in the cabinet.γ is 0° when the 90°-stub is inserted into the SBO.For each course sector width (CS) of the array a set of corresponding DDM values exists unique for each antenna O/P.For CS = 4°:For other CS values use the formula:ExampleA3 DDM for CS = 3.5°:PROCEDURETurn off the clearance transmitter. Insert the 90°-stub into the course SBO path. Connect a directional coupler with 50Ω load to antenna O/P A3.Connect the NM3710 (use 20 dB attenuator at NM3710 I/P) to the directional coupler's for-ward port.Adjust the SBO attenuator (for the Tx to air) until the DDM value equals the previously calcu-lated value for the CS.Move the directional coupler to A4, A5 and compare readings with calculated values. If mea-sured DDM is lower than the calculated values for A4, A5 then increase the SBO power, or vice versa, until a fairly good matching set of values are obtained.Adjust the SBO attenuator for the other Tx to the same setting.Remove the 90°-stub.A3 -33.0% DDMA4 -29.3% DDMA5 -26.0% DDMDDM 2SBO⋅CSB-------------------COSγ=DDMAn()DDM 4°()4°⋅CS---------------------------------=DDMA333.0 4⋅–3.5---------------------37%–==

 4.3.2 Clearance SBO powerSwitch off the course transmitter.Insert the 90°-stub in the CLR SBO path. Connect the Field Test Set to the BNC test connec-tor TEST 1 (antenna 13 sample) in the ADU. (Use 20...30 dB attenuator at the Field Test Set I/P).Switch on the clearance transmitter. Adjust the CLR SBO attenuator in the cabinet (associ-ated with Tx to air) until a reading of 36% DDM is obtained.Carry out the same procedure for the other transmitter.4.3.3 DDM field checkSet the localizer to normal radiation (clearance transmitter on). From the centreline of the opposite threshold determine points perpendicular to the CL 105 meter to both sides of the runway. Use the NM3710 with portable antenna and measure DDM at these points. The read-ings should be close to -15.5% at the 90-side and 15.5% at the 150-side. However, some unsymmetry may be expected due to reflections and tolerances in the antenna system.Check the CL DDM at two or three positions in order to estimate an average value.Expected value: 0.0% ±0.2% DDM.4.4 Monitor combining unit (MCU) adjustments4.4.1 Course LineConnect the Field Test Set to the CL output connector of the MCU.Adjust the CL line stretcher to obtain 0.0% DDM.4.4.2 Course SectorConnect the Field Test Set to the CS output of the MCU.Adjust the CS line stretcher to obtain a reading of 15.5% DDM.4.4.3 ClearanceConnect the Field Test Set to the CLR output connector of the MCU. Adjust the CLR line stretcher to obtain a reading of 27% DDM.4.5 Near field monitor adjustmentsThe exact position of the near field monitor antenna cannot be determined until after the flight check is completed, due to possible mechanical re-alignment of the antenna array.4.5.1 Mechanical alignmentAlign the near field (NF) monitor antenna mechanically in the extended runway centreline position.

4.5.2 Final electrical position adjustmentConnect the Field Test Set to the NF monitor cable. The reading should be 0.0% DDM if the antenna is aligned correctly and no reflections appear.Otherwise, a small mechanical re-positioning of the antenna may be necessary in order to obtain 0.0% DDM.4.6 DC-Loop adjustment and testing4.6.1 DC-LOOP adjustmentThe DC loop (cable fault monitor) alignment is carried out accordingly to the procedure described in Monitor Alignment and Calibration chapter.4.6.2 Antenna fault condition testingFor this test observe that the LLZ cabinet System Status indicates ALARM.The transmitter must be on during this test.The monitors should be in MANUAL mode in order to prevent transmitter from being shut off during the test.Disconnect one antenna at a time and check that the LLZ cabinet System Status indicates ALARM after each antenna disconnection.Carry out this test for all antennas.

 5 NM 3526 16 Elements antenna system adjustments - LLZ5.1 Mechanical alignments of antenna array5.1.1 Right angle points with reference to runway centre lineThe alignment of the antenna array perpendicular to the runway centreline should be carried out to an accuracy of 0.01°.This corresponds to within 4 mm accuracy at positions antenna 1 and antenna 16. A theodo-lite should be utilised.5.1.2 Spacing distance between LPDA’sCheck that the spacing between each LPDA is according to dimensions given in dwg.no. 16362A3.Tolerance: ±5 mm.5.1.3 Vertical alignment of LPDA support mastsOn each rear support mast for LPDA check with waterlevel that mast is vertically aligned in both planes.5.1.4 Azimuth alignment of LPDA’sDetermine a fixed point as far as possible along the extended centreline not less than approx-imately 3000 m from the antenna array.On each LPDA utilise the top horizontal line composed of the two half sections of the radome to point toward the fixed point.If necessary adjust the LPDA horizontally by adjusting the mast supports on the front mast, so that the extended radome top line ends at the fixed point.5.2 Electrical measurements5.2.1 CSB and SBO cablesCourse Tx cables.The CSB and SBO cable between the cabinet and MCU must be of equal electrical length. Utilise a vector voltmeter or network analyser in a test set-up as in Figure 5-1.Measure open cable return phase for each cable.Refer to CSB cable as zero phase and measure the return phase for the SBO cable. The cable pair must be matched within ±3.0° return phase, equal to ±1.5° true phase.Clearance Tx cables.Repeat the procedure 1.2.1 for CLR Tx CSB and SBO cables

$.Figure 5-1 Cable phasing measurement set-up.5.2.2 CSB/SBO phasing127(6ZLWFKRIIWKHFOHDUDQFHWUDQVPLWWHU$VFHUWDLQWKDWWKH7[PRGXODWRUXVHGLVRSWLPDOO\FDOLEUDWHGConnect the NM3710 Field Test Set to the monitor BNC test connector in the ADU. (Use 20..30 dB attenuator at the I/P of the Field Test Set.)Adjust SBO phaser in the Cabinet (associated with Tx to air) to obtain 0.0% DDM reading.Repeat the phasing procedure for the other transmitter.Switch off the course transmitter.With the clearance transmitter on repeat the phasing procedure now adjusting the clearance SBO phaser associated with Tx to air. 5.2.3 Antenna cable lengths (Electrical phase equality)Each antenna cable should be electrically checked before the end connector is terminated in the LPDA.Utilise a vector voltmeter or network analyser. Establish antenna cable (A1) (leftmost seen from rear) return phase as 0° reference phase.Measure return phase for each of the remaining antenna cables (A2...A16).Tolerance: ±1.0° true electrical cable length. See measurement set-up diagram Figure 5-120dBABVECTORFrom cabinetCSB BNC o/pCABLE UNDER TESTOPEN ENDDIR. COUPL.$

$ 5.2.4 Antenna pair phasing127(%HIRUHWKHDQWHQQDSDLUSKDVLQJSURFHGXUHLVFRPPHQFHGDVFHUWDLQWKDWWKH7[PRGXODWRUXVHGLVRSWLPDOO\FDOLEUDWHG6ZLWFKRIIWKHFOHDUDQFHWUDQVPLWWHUConnect the antenna cables A1 and A16 to the ADU outputs labelled A1 and A16 respec-tively.Connect all other ADU outputs to dummy load. Use the NM3710 with portable test antenna.On the the runway establish a point officially marked as the centre line for DDM measure-ments. Ascertain that the measurement point is not affected by reflected signals upsetting the direct received signals from the antenna pairs. This can be tested by moving the test antenna a few meters back and fourth while observing the DDM reading. If the value is not changing then the measurement position is OK.Take a note of the DDM reading first from antenna pair A1/A16.Connect pair A2/A15 to ADU outputs A2/A15 and disconnect pair A1/A16, dummyload A1/A16 ADU.Take a note of the DDM reading.Carry out this procedure until all antenna pairs DDM readings have been noted.If any antenna pair measures DDM different from zero, one of the antenna pair feed cable lengths should be trimmed in order to bring the DDM reading to zero.If the DDM reading is positive (150 Hz dominance) the antenna cable at the right hand side (A8...A16) should be trimmed.The sensitivity of DDM versus electrical phase error of 2° (4° CS) is given in the table below:Pair DDM µADDM % A1/A16 12.6 1.30A2/A15 7.5 0.78A3/A14 5.7 0.59A4/A13 4.2 0.43A5/A12 2.8 0.29A6/A11 2.0 0.21A7/A10 1.1 0.11A8/A9 0.4 0.04$

The sensitivity of DDM versus electrical phase error can be estimated using the following pro-cedure:1. Note the DDM value reported by the operator at the Field Test Set for the antenna pair under test. 2. a) If the DDM value is positive (150 Hz dominance), insert a male-female (MF) N-adaptor (-9°) in the antenna left side seen forward toward the Field test set. b) If the DDM value is negative (90 Hz dominance), insert a male-female (MF) N-adaptor (-9°) in the antenna right side seen forward toward the Field test set.3. Note the new DDM value. (This value should have oposite polarity compared to the value without the adaptor.)4. Calculate the corresponding phase error (electrical degrees) from the formulaDDM1 : DDM (%) measured in item 1.DDM3 : DDM (%) measured in item 3.(Example values from NM3523B)Example 1:Item 1: A1/A12: +4.3% DDMItem 3: A1+MF/A12: -2.0% DDM (MF in A1) Example 2:Item 1: A6/A7: -0.6% DDMItem 3: A6 /A7+MF: +1.86% DDM (MF in A7)Cable trimming length: 6.2 mm/°.5.2.5 Phase and amplitude transfer measurementConnect each antenna cable and monitor cable to LPDA load and source respectively. Utilise a vector voltmeter or network analyser in a test set-up Figure 5-2ϕ°() 9°DDM1DDM1DDM3+-------------------------------------------=ϕ9°4.3⋅4.3 2.0+---------------------4.8°==ϕ9°0.6⋅0.6 1.86+------------------------1.7°==

 .Figure 5-2 Phase and amplitude transfer measurement set-up.Measure relative transfer phase and amplitude for each Antenna/Monitor return cable in ref-erence to A1/M1.Then determine if one of the monitor cables must be trimmed in order to comply with phase tolerance for the set of cables.Tolerance: ±2°.Amplitude tolerance: ±1.0 dB. If the amplitude tolerance is exceeded something might be wrong in the LPDA monitor circuit or connector/cable.Record the final result in Ground Commissioning Record.5.2.6 Antenna return lossUtilise a vector voltmeter or network analyser in a test set-up Figure 5-3. Measure return loss for each LPDA.Measure and record in Ground Commissioning Record the return loss value for each LPDA including antenna cable.Tolerance: 20 dB minimum.Figure 5-3 Antenna return loss measurement set-up.20dBABVECTOR VOLTMETERA(n)M(n)From cabinetCSB BNC o/pAnt.DIR. COUPL.20dBABVECTOR VOLTMETERFrom cabinetCSB BNC o/pDIR. COUPL.Antenna cable under testAntenna

5.3 Course sector width adjustmentThe required course sector width (CS) can be pre-adjusted by two methods:1. DDM measurement of ADU antenna feed outputs.2. DDM field check.Preferably both methods should be carried out and compared.5.3.1 DDM check of ADU O/PAt each antenna feed output of the ADU the measured DDM is a result of the SBO/CSB ratio according to the formulawhereCSB is a fixed value.SBO is adjustable by the SBO attenuator in the cabinet.γ is 0° when the 90°-stub is inserted into the SBO and clearance transmitter is switched off.For each course sector width (CS) of the array a set of corresponding DDM values exists unique for each antenna O/P.For CS = 4°:For other CS values use the formula:ExampleA3 DDM for CS = 3.5°:PROCEDURETurn off the clearance transmitter. Insert the 90°-stub into the course SBO path. Connect a directional coupler with 50Ω load to antenna O/P A3.% DDM µA% SDMA3 -33.7 -326 40.0A4 -24.9 -241 40.0A5 -17.9 -173 40.0DDM 2SBO⋅CSB-------------------COSγ=DDMAn()DDM 4°()4°⋅CS---------------------------------=DMA3() 33.7 4⋅–3.5---------------------38.5%==

 Connect the NM3710 (use 20 dB attenuator at NM3710 I/P) to the directional coupler’s for-ward port.Adjust the SBO attenuator (for the Tx to air) until the DDM value equals the previously calcu-lated value for the CS.Move the directional coupler to A4, A5 and compare readings with calculated values. If mea-sured DDM is lower than the calculated values for A4, A5 then increase the SBO power, or vice versa, until a fairly good matching set of values are obtained.Adjust the SBO attenuator for the other Tx to the same setting.Remove the 90°-stub.5.3.2 Clearance SBO powerSwitch off the course transmitter.Insert the 90°-stub in the CLR SBO path. Connect the Field Test Set to the BNC test connec-tor (antenna 4 sample) in the ADU. (Use 20...30 dB attenuator at the Field Test Set I/P).Switch on the clearance transmitter. Adjust the CLR SBO attenuator in the cabinet (associ-ated with Tx to air) until a reading of 43.6% SDM is obtained.Carry out the same procedure for the other transmitter.5.3.3 DDM field checkSet the localizer to normal radiation (clearance transmitter on). From the centreline of the opposite threshold determine points perpendicular to the CL 105 meter to both sides of the runway. Use the NM3710 with portable antenna and measure DDM at these points. The read-ings should be close to -15.5% at the 90-side and 15.5% at the 150-side. However, some unsymmetry may be expected due to reflections and tolerances in the antenna system.Check the CL DDM at two or three positions in order to estimate an average value.Expected value: 0.0%±0.2% DDM.5.4 Monitor combining unit (MCU) adjustments5.4.1 Course LineConnect the Field Test Set to the CL output connector of the MCU.Adjust the CL line stretcher to obtain 0.0% DDM.5.4.2 Course SectorConnect the Field Test Set to the CS output of the MCU.Adjust the CS line stretcher to obtain a reading of 15.5% DDM.

5.4.3 ClearanceConnect the Field Test Set to the CLR output connector of the MCU and use the acual DDM as standard signal to the monitors.5.5 Near field monitor adjustmentsThe exact position of the near field monitor antenna cannot be determined until after the flight check is completed, due to possible mechanical re-alignment of the antenna array.5.5.1 Mechanical alignmentAlign the near field (NF) monitor antenna mechanically in the extended runway centreline position.5.5.2 Final electrical position adjustmentConnect the Field Test Set to the NF monitor cable. The reading should be 0.0% DDM if the antenna is aligned correctly and no reflections appear.Otherwise, a small mechanical re-positioning of the antenna may be necessary in order to obtain 0.0% DDM.5.6 DC-Loop adjustment and testing5.6.1 DC-LOOP adjustmentThe DC loop (cable fault monitor) alignment is carried out accordingly to the procedure described in Monitor Alignment and Calibration chapter.5.6.2 Antenna fault condition testingFor this test observe that the LLZ cabinet System Status indicates ALARM.The transmitter must be on during this test.The monitors should be in MANUAL mode in order to prevent transmitter from being shut off during the test.Disconnect one antenna at a time and check that the LLZ cabinet System Status indicates ALARM after each antenna disconnection.Carry out this test for all antennas.

 6 NM 3543 Null reference antenna system adjustments - Glide path6.1 Mechanical alignment of mast and antennas6.1.1 Preparation of mechanical- and electrical dataA ground level plot made with theodolite should be available. From this plot Forward slope (FSL) and Sideway slope (SSL) can be calculated. FSL is defined negative for falling forward slope seen from the GP mast. SSL is defined positive for rising side slope seen from the GP mast toward the runway.In order to calculate the data needed to position the GP mast, the antenna elements and near field antenna, the following parameters must be known:• Forward slope (FSL)• Sideway slope (SSL)• Sideway distance from runway centreline to GP mast• Operating glide path angle• GP rf channel frequencyThe mechanical data outputs are:• Antenna forward shift, same as FSL• Antenna elements heights• Antenna elements offsets• Near field monitor antenna distance and height• Threshold data6.1.2 Forward shift (FWD)The antennas should be vertically offset to compensate for forward slope (FSL). See Section 1, Chapter 3.6.3.6.1.3 Antenna heightsAntenna heights shall be referenced to the intercept point of the terrain slope and the GP mast. In addition rf wave penetration a few centimetres into the soil (reflection plane) shall be included to equal the specified antenna heights. See Section 1, Chapter 3.6.3.6.1.4 Antenna offsets.The antenna offsets derived from (51.0) shall be accurately adjusted such that the upper ele-ment is closer to the runway than the lower element. See Section 1, Chapter 3.6.3.6.2 Electrical measurements6.2.1 Antenna cable lengths (Electrical phase equality)Each antenna cable must be electrically measured before the end connector is terminated in the Antenna.Utilise a vector voltmeter or network analyser. Establish the lower antenna cable (A1) return phase as 0° reference phase.

Measure return phase for the upper antenna cable (A2). Then take into account the phase centres of the Antenna given in the factory data sheet. Determine if one of the cables should be trimmed in order to comply with phase equality tolerance for the set of antennas.Tolerance: ±1.0° true electrical cable length including Antenna phase centre deviation. (if available)See measurement set-up diagram Figure 6-1Figure 6-1 Cable phasing measurement set-up.6.2.2 Monitor return cable lengthMeasure return phase as described in (52.0) for both monitor cables. Check that initial values are within ±1.5° true phase (±3.0° return phase).6.2.3 Phase and amplitude transfer measurementConnect each antenna cable and monitor cable to Antenna load and source respectively. Uti-lise a vector voltmeter or network analyser in a test set-upFigure 6-2 Phase and amplitude transfer measurement set-up.20dBABVECTORFrom cabinetCSB BNC o/pCABLE UNDER TESTOPEN ENDDIR. COUPL.20dBABVECTOR VOLTMETERA(n)M(n)From cabinetCSB BNC o/pAnt.DIR. COUPL.

 Measure and record phase/amplitude for upper antenna transfer signals. Then determine if one of the monitor cables must be trimmed in order to comply with phase tolerance for the set of cables.Tolerance: ±1°.Amplitude tolerance: ±1.0 dB. If the amplitude tolerance is exceeded something might be wrong in the Antenna monitor circuit or connector/cable.Record final result in Ground Commissioning Records.6.2.4 Antenna return lossUtilise a vector voltmeter or network analyser in a test set-up Figure 6-3. Measure return loss for each Antenna.Measure and record in Ground Commissioning Record the return loss value for each Antenna including antenna cable.Tolerance: 20 dB minimum.Figure 6-3 Antenna return loss measurement set-up.6.3 CSB/SBO Phasing and sector width adjustmentSee Figure 6-46.3.1 CSB/SBO phasingA 180° hybrid can be utilised to adjust (preset) the phase between CSB and SBO.Connect the O/P CSB cable from the Cabinet to port 1. Connect the O/P SBO cable from the Cabinet to port 3.Insert the 90°-stub into the SBO path.20dBABVECTOR VOLTMETERFrom cabinetCSB BNC o/pDIR. COUPL.Antenna cable under testAntenna

$The hybrid port 4 is terminated in 50Ω, min. 5 watts dummy load. Port 2 is connected to a directional coupler which is terminated in 50Ω, min. 5 watts dummy load. The directional cou-pler forward port is connected to NM3710 Field Test Set. Use 20 dB attenuator at the BNC I/P of NM3710.The NM3710 DDM should be 0.0%. If necessary adjust the SBO phaser of associated trans-mitter in the Cabinet to 0.0% DDM. Carry out the same procedure for the other transmitter.6.3.2 Sector Width adjustmentFigure 6-4 test set-up is used. Remove the 90°-stub.The NM3710 DDM should be 23.4%. If necessary adjust the SBO attenuator of associated transmitter in the Cabinet to obtain 23.4% DDM. Carry out the same procedure for the other transmitter.127(7RFRPSHQVDWHIRUDVORSLQJWHUUDLQLQIURQWRIWKH*3WKH''0DFFRUGLQJO\VKRXOGEHwhere θ0 is the glide path angleFSL is forward slope, negative sign for falling terrain referred from the GP.Figure 6-4 Measurement set-up for CSB/SBO phasing and Sector Width adjustment.DDM 11.7 θ0FSL–()θ0--------------------------------------=12340°0°0°180°180° HYBRID50Ω 50ΩCSBSBO 20dB NM3710FIELD TEST SET$

 6.4 Monitoring combining unit (MCU) adjustments6.4.1 ProcedureInsert the 90°/stub in the SBO output of the NM3531 Cabinet.Connect the Field Test Set to the CL output of the MCU. Check that the reading is 0% ±0.5% DDM.Remove the 90°-stub from the SBO path.Connect the Field Test Set to the DS output of the MCU. Adjust the MCU attenuator at A2 to obtain 17.5% DDM.6.5 Location of near field antenna positionAccording to site data (slope, etc.,) the theoretical position of the NF antenna should be calcu-lated.6.5.1 Near Field Monitor Position SearchInstall the NF antenna at the position according to calculations (distance and height). Adjust the height to obtain 0 DDM reading on the Field Test Set connected to the NF monitor cable. (Ladder and personnel must be vacated from the NF area.)

 7 NM 3544 Sideband reference antenna system adjustment - Glide path 7.1 Mechanical alignment of mast and antennas7.1.1 Preparation of mechanical- and electrical dataA ground level plot made with theodolite should be available. From this plot Forward slope (FSL) and Sideway slope (SSL) can be calculated. FSL is defined negative for falling forward slope seen from the GP mast. SSL is defined positive for rising side slope seen from the GP mast toward the runway.In order to calculate the data needed to position the GP mast, the antenna elements and near field antenna, the following parameters must be known:• Forward slope (FSL)• Sideway slope (SSL)• Sideway distance from runway centreline to GP mast• Operating glide path angle• GP rf channel frequencyThe mechanical data outputs are:• Mast tilt, same as FSL• Antenna elements heights• Antenna elements offsets• Near field monitor antenna distance and height• Threshold data7.1.2 Forward shift (FWD)The antennas should be vertically offset to compensate for forward slope (FSL). See Section 1, Chapter 3.6.3.7.1.3 Antenna heightsAntenna heights shall be referenced to the intercept point of the terrain slope and the GP mast. In addition rf wave penetration a few centimetres into the soil (reflection plane) shall be included to equal the specified antenna heights. See Section 1, Chapter 3.6.3.7.1.4 Antenna offsetsThe antenna offsets derived from (61.0) shall be accurately adjusted such that the Upper ele-ment is closer to the runway than the lower element. See Section 1, Chapter 3.6.3.7.2 Initial electrical measurements7.2.1 Antenna cable lengths (Electrical phase equality)Each antenna cable must be electrically measured before the end connector is terminated in the Antenna.Utilise a vector voltmeter or network analyser. Establish the lower antenna cable (A1) return phase as 0° reference phase.

$7.3.2 CSB/SBO phasingInsert the 90°-stub in the SBO cable path to the ADU. Connect the NM3710 Field Test Set to the monitor return cable (M1) from the lower antenna.Adjust SBO phaser in the Cabinet (associated with Tx to air) to obtain 0 DDM reading.Repeat the phasing procedure for the second transmitter.Remove the 90°-stub from the SBO path.7.4 Sector width adjustment7.4.1 SBO power adjustmentConnect the Field Test Set to the monitor return cable (M1) from the lower antenna.Adjust the SBO step attenuator in the cabinet (associated with Tx to air) to obtain the pre-scribed DDM value.For a perfect flat terrain the DDM in A1 (M1) should be -11.7%.127(7RFRPSHQVDWHIRUDVORSLQJWHUUDLQLQIURQWRIWKH*3WKH''0DFFRUGLQJO\VKRXOGEHwhere θ is the glide path angleFSL is forward slope, negative for falling terrain referred from the GP.Repeat the SBO attenuator adjustment for the second transmitter.7.5 Monitor combining unit (MCU) adjustments7.5.1 Procedure for horizontal terrain (FSL = 0°)Connect the Field Test Set to the CL output of the MCU. Adjust the MCU phaser at A1 (lower antenna) to read 0% DDM.Remove the 90°-stub from the SBO path. Adjust the MCU attenuator at A1 to read 0% DDM at the CL output.Connect the Field Test Set to the DS output of the MCU. Read the DDM value. This should be 8.75% DDM unless a SBO power compensation for sloping foreground and K3, K4 cable length compensation has been taken into account (See 1.5.2).7.5.2 Procedure for sloping terrain (1° > FSL > -1°)If the terrain in front of the GP is not horizontal, cable lengths K3 and K4 should be changed in accordance with the table below:DDM 11.7 θ0FSL–()–θ0-----------------------------------------=$

 FSL (+) : Upsloping terrain. (-) mm means shorter cable.After cable length modification carry out procedure 1.5.1. Note that DS DDM after adjustment should correspond to the value given in the table above (column 4). However, the final DS DDM value depends on the SBO power setting of the Tx SBO attenuator.7.6 Location of near field antenna positionAccording to site data (slope, etc.,) the theoretical position of the NF antenna should be calcu-lated.Install the NF antenna at the position according to calculations (distance and height). Adjust the height to obtain 0% DDM reading on the Field Test Set connected to the NF monitor cable. (Ladder and personnel must be vacated from the NF area.) FSL (°) K3 (mm) K4 (mm) DS DDM (%)1.0 -27 -18 10.30.9 -23 -15 10.10.8 -19 -13 9.90.7 -16 -11 9.70.6 -13 -9 9.50.5 -11 -7 9.40.4-8-59.30.3-6-49.20.2-4-39.00.1-2-28.90.0 0 0 8.75-0.1 2 1 8.6-0.2 3 2 8.5-0.3 5 3 8.4-0.4 6 4 8.3-0.5 8 5 8.2-0.6 9 6 8.1-0.7 10 7 8.0-0.8 11 7 7.9-0.9 12 8 7.8-1.0 13 9 7.8

Theoretically, DDM should be close to -0.9% DDM (90) as a minimum value due to path loss differences between antennas seen from the NF antenna.7.6.1 Near Field Monitor Position SearchA de-phasing test procedure of upper antenna (A2) can be carried out in order to search for the optimum monitor position.An "elbow" type N-adapter (-21°) is inserted in the lower antenna feed (A1). This is equivalent to advance (+) phase of the upper antenna.Retard (-) phase is introduced by inserting the "elbow" adapter in A2 only.The DDM readings and correlation of the monitor antenna signal to the CL integral from MCU (far field) should theoretically be:127(7KHYDOXHVDWWKH1)SRVLWLRQDUHQRUPDOLVHGLH''0ZLWKQR$GHSKDVLQJIn order to look for the optimal distance between the GP mast and the NF antenna carry out the following test:Measure DDM at positions +1 m and -1 m of original position. Then compare the results with the theoretical values for these offsets from the nominal 180° position, as denoted below:127(:KHQPRYLQJWKH1)DQWHQQDSRVLWLRQEDFNZDUGDQGIRUZDUGWDNHLQWRDFFRXQWWKHRIIVHW''0IRUQRGHSKDVLQJLHQRUPDOLVHWKHYDOXHVEHIRUHFRPSDULQJWRWKHRUHWLFDOYDOXHVBased on the comparing results then determine the best correlated position for the NF monitor antenna.Dephasing Near Field (NF) Far field (CL)21° retard -13µA/-1.5% DDM -11µA/-1.3% DDM21° advance -11µA/-1.3% DDM -13µA/-1.5% DDMDephasing NF 1 m forward NF 1 m backward21° retard -19µA/-2.2% DDM -9µA/-1.1% DDM21° advance -7µA/-0.8% DDM -16µA/-1.9% DDM

 7.7 Antenna distribution unit (ADU) phase and amplitude check7KLVFKHFNLVRSWLRQDO7.7.1 PreparationUtilise a vector voltmeter in a test set-up Figure 7-4 .Figure 7-4 Test set-up for ADU Phase and Amplitude check.Connect CSB and SBO outputs from Cabinet to dummy loads. Terminate the disconnected cables from ADU to dummy loads.Switch off the modulation to the transmitter used for the test.Insert a 20 dB attenuator at the input port of the directional coupler.Connect a test cable from the Cabinet’s CSB BNC connector to the 20 dB attenuator.Connect the vector voltmeter A-probe to the directional coupler’s forward O/P.7.7.2 Procedure1. Connect the cable TEST SIG (throughput from the directional coupler) to the ADU SBO I/P.Connect the B-probe to L O/P. Note the B-probe RF level (dB). (0.1 dB resolution)Move the B-probe to U O/P. If necessary adjust phaser PH1 (AMPLITUDE ADJ) to obtain 0.0 dB difference referenced to L O/P.127(,I3+KDVEHHQDGMXVWHGUHFKHFNWKHUHIHUHQFHOHYHOIURP/23DQGPHDVXUHDJDLQWKH823OHYHO5HSHDWXQWLOG%GLIIHUHQFHLVDFKLHYHG2. Connect the cable TEST SIG to the SBO input. Connect the B-probe to L O/P. Adjust the 20dBABVECTOR VOLTMETERFrom cabinetCSB BNC o/p50ΩADUSBOCSBULDIR. COUPL.

vector voltmeter to 0° reference phase.Move the B-probe to U O/P. If necessary adjust SBO U/L phaser (PH2) to obtain 180° reading at the U O/P.127(,I3+KDVEHHQDGMXVWHGUHFKHFNWKHUHIHUHQFHSKDVHIURP/23DQGPHDVXUHDJDLQWKH8SKDVH5HSHDWXQWLOSKDVHGLIIHUHQFHLVDFKLHYHGEnd of check.

 8 NM 3545 M-Array antenna system adjustments - Glide path8.1 Mechanical alignment of mast and antennas8.1.1 Preparation of mechanical- and electrical dataA ground level plot made with theodolite should be available. From this plot Forward slope (FSL) and Sideway slope (SSL) can be calculated. FSL is defined negative for falling forward slope seen from the GP mast. SSL is defined positive for rising side slope seen from the GP mast toward the runway.In order to calculate the data needed to position the GP mast, the antenna elements and near field antenna, the following parameters must be known:• Forward slope (FSL)• Sideway slope (SSL)• Sideway distance from runway centreline to GP mast• Operating glide path angle• GP rf channel frequencyThe mechanical data outputs are:• Mast tilt, same as FSL• Antenna elements heights• Antenna elements offsets• Near field monitor antenna distance and height• Threshold data8.1.2 Forward shift (FWD)The antennas should be vertically offset to compensate for forward slope (FSL). See Section 1, Chapter 3.6.3.8.1.3 Antenna heightsAntenna heights shall be referenced to the intercept point of the terrain slope and the GP mast. In addition rf wave penetration a few centimetres into the soil (reflection plane) shall be included to equal the specified antenna heights. See Section 1, Chapter 3.6.3.8.1.4 Antenna offsetsThe antenna offsets derived from (71.0) shall be accurately adjusted such that the upper ele-ment is closer to the runway than the lower element. See Section 1, Chapter 3.6.3.8.2 Initial electrical measurements8.2.1 Antenna cable lengths (Electrical phase equality)Each antenna cable must be electrically measured before the end connector is terminated in the Antenna.Utilise a vector voltmeter or network analyser. Establish the lower antenna cable (A1) return phase as 0° reference phase.

Measure return phase for the middle antenna cable (A2) and upper antenna cable (A3). Then take into account the phase centres of the Antennas given in the factory data sheet. Deter-mine if one of the cables should be trimmed in order to comply with phase equality tolerance for the set of antennas.Tolerance: ±1.0° true electrical cable length including Antenna phase centre deviation. (if available)See measurement set-up diagram Figure 8-1 below:Figure 8-1 Cable phasing measurement set-up.8.2.2 Monitor return cable lengthMeasure return phase as described in (72.0) for all three monitor cables. Check that initial values are within ±1.5° true phase (±3.0° return phase).8.2.3 Phase and amplitude transfer measurementConnect each antenna cable and monitor cable to Antenna load and source respectively. Uti-lise a vector voltmeter or network analyser in a test set-up Figure 8-2, and measure relative transfer phase and amplitude for the middle and upper antenna cable (A2 & A3) in reference to the lower antenna (A1).Figure 8-2 Phase and amplitude transfer measurement set-up.20dBABVECTORFrom cabinetCSB BNC o/pCABLE UNDER TESTOPEN ENDDIR. COUPL.20dBABVECTOR VOLTMETERA(n)M(n)From cabinetCSB BNC o/pAnt.DIR. COUPL.

the monitor return cable (M1) from the lower antenna.Adjust SBO phaser in the Cabinet (associated with Tx to air) to obtain 0 DDM reading.Repeat the phasing procedure for the second transmitter.Remove the 90°-stub from the SBO path.8.4 Sector width adjustment8.4.1 SBO power adjustmentConnect the Field Test Set to the monitor return cable (M1) from the lower antenna.Adjust the SBO step attenuator in the cabinet (associated with Tx to air) to obtain the pre-scribed DDM value.For a perfect flat terrain the DDM in A1 (M1) should be -11.7%.NOTE. To compensate for a sloping terrain in front of the GP the DDM accordingly should be:where θ is the glide path angleFSL is forward slope, negative for falling terrain referred from the GP.Repeat the SBO attenuator adjustment for the second transmitter.8.5 Monitor combining unit (MCU) MOA 338D adjustmentsMonitor Combining Unit MOA338D is equipped with plug-in attenuators dependent upon for-ward slope, according to the following table (AT6 is common for all FSL):Make sure that correct attenuators are installed for the actual site.FSL rel.to θ0Equiv.FSLin degrees for θ0= 3°AT3Type AT4Type AT5Type AT7Type-0.2θ0 ± 0.05θ0-0.6° ± 0.15°AT1305B AT1305G AT1305MAT1305S-0.1θ0 ± 0.05θ0-0.3° ± 0.15°AT1305C AT1305H AT1305N AT1305T 0.0θ0 ± 0.05θ0 0.0° ± 0.15°AT1305D AT1305J AT1305P AT1305U+0.1θ0 ± 0.05θ0+0.3° ± 0.15°AT1305E AT1305K AT1305Q AT1305V+0.2θ0 ± 0.05θ0+0.6° ± 0.15°AT1305F AT1305L AT1305B AT1305WDDM 11.7 θ0FSL–()–θ0-----------------------------------------=

 8.5.1 Adjustments procedureThe Clearance transmitter shall be switched off during steps a) through e) below.1. Connect the Field Test Set to the CL output of the MCU. Insert the 90° stub in the SBO out-put of the Transmitter Cabinet. In the Antenna Distribution Unit (ADU), disconnect SBO to Lower antenna by using the SBO-L link. Terminate open ends. Adjust Upper antenna phaser PH1 in MCU to give 0% DDM.2. Reconnect SBO to Lower antenna. Remove the 90° stub. Adjust CL attenuator AT1 in MCU to give 0 % DDM.3. Connect the Field Test Set to the DS output of the MCU. Insert the 90° stub in the SBO out-put of the Transmitter Cabinet. Adjust Middle antenna phaser PH2 in MCU to give 0% DDM.4. Remove the 90° stub. Adjust DS attenuator AT2 in MCU to give 8.75% DDM (75µA), 150 Hz dominance.5. Connect the Field Test Set to the CLR output of the MCU. Adjust phaser PH3 in MCU to maximum DDM (150 Hz dominance).6. Turn on CLR transmitter. Check that sufficient 150Hz dominance remains.8.6 Location of near field antenna positionAccording to site data (slope, etc.,) the theoretical position of the NF antenna should be calcu-lated.Install the NF antenna at the position according to calculations (distance and height). Adjust the height to 0 DDM reading on the Field Test Set connected to the NF monitor cable. (Ladder and personnel must be removed from the NF area.) 8.6.1 Near Field Monitor Position SearchA de-phasing test procedure of upper antenna (A3) can be carried out in order to search for the optimum monitor position.A N-type adapter (-27°) (made from a male-male and female-female adapter put together) is inserted in the lower antenna feed (A1) and middle antenna feed (A2). This is equivalent to advance (+) phase of the upper antenna.Retard (-) phase is introduced by inserting the adapter in upper antenna feed A3 only.The DDM readings and correlation of the monitor antenna signal to the CL integral from MCU (far field) should theoretically be:Dephasing Near Field (NF) Far field (CL)27° retard -12µA/-1.4% DDM -11µA/-1.3% DDM27° advance -9µA/-1.1% DDM -11µA/-1.3% DDM

$127(7KHYDOXHVDWWKH1)SRVLWLRQDUHQRUPDOLVHGLH''0ZLWKQR$GHSKDVLQJIn order to look for the optimal distance between the GP mast and the NF antenna carry out the following test:Measure DDM at positions +1 m and -1 m of original position. Then compare the results with the theoretical values for these offsets from the nominal 360° position, as denoted below:127(:KHQPRYLQJWKH1)DQWHQQDSRVLWLRQEDFNZDUGDQGIRUZDUGWDNHLQWRDFFRXQWWKHRIIVHW''0IRUQRGHSKDVLQJLHQRUPDOLVHWKHYDOXHVEHIRUHFRPSDULQJWRWKHRUHWLFDOYDOXHVBased on the comparing results then determine the best correlated position for the NF monitor antenna.8.7 Antenna distribution unit (ADU) DIA 346A phase and amplitude check7KLVFKHFNLVRSWLRQDO,ILWLVFDUULHGRXWLWVKRXOGSUHIHUDEO\EHH[HFXWHGSULRUWRVWHS8.7.1 PreparationUse a vector voltmeter in a test set-up figure 8-4.Figure 8-4 Test set-up for ADU Phase and Amplitude check.Connect CSB and SBO outputs from Cabinet to dummy loads. Terminate the disconnected cables from ADU to dummy loads.Dephasing NF 1 m forward NF 1 m backward27° retard -16µA/-1.9% DDM -9µA/-1.1% DDM27° advance -5µA/-0.6% DDM -12µA/-1.4% DDM20dBABVECTOR VOLTMETERFrom cabinetCSB BNC o/pDir. coupl.50ΩADUCSBSBOUML$

 The clearance transmitter shall be switched off.Switch off the modulation to the transmitter used for the test.Insert a 20 dB attenuator at the input port of the directional coupler.Connect a test cable from the Cabinet’s CSB BNC connector to the 20 dB attenuator.Connect the vector voltmeter A-probe to the directional coupler’s forward output.8.7.2 Procedure1. Connect the cable TEST SIG (throughput from the directional coupler) to the ADU CSB input.Connect the B-probe to L output. Note the B-probe RF level (dB). (0.1 dB resolution)Move the B-probe to M output. If necessary adjust phaser D1 to obtain -6.0 dB difference referenced to L output.127(,I'KDVEHHQDGMXVWHGUHFKHFNWKHUHIHUHQFHOHYHOIURP/RXWSXWDQGPHDVXUHDJDLQWKH0RXWSXWOHYHO5HSHDWXQWLOG%GLIIHUHQFHLVDFKLHYHG2. Connect the cable TEST SIG to the SBO input. Connect the B-probe to U output. Note the level.Move the B-probe to the L output. If necessary adjust phaser D3 to obtain 0.0 dB difference referenced to U output.127(,I'KDVEHHQDGMXVWHGUHFKHFNWKHUHIHUHQFHOHYHOIURP8RXWSXWDQGPHDVXUHDJDLQWKH/RXWSXWOHYHO5HSHDWXQWLOG%GLIIHUHQFHLVDFKLHYHG3. Connect the B-probe to M output. Note the level.Move the B-probe to L output.If necessary adjust phaser D2 to obtain -6.0 dB difference referenced to M output.127(,I'KDVEHHQDGMXVWHGUHFKHFNWKHUHIHUHQFHOHYHOIURP/RXWSXWDQGPHDVXUHDJDLQWKH02RXWSXWOHYHO5HSHDWXQWLOG%GLIIHUHQFHLVDFKLHYHG4. Connect the cable TEST SIG to the SBO input. Connect the B-probe to M output. Adjust the vector voltmeter to 0° reference phase.Move the TEST SIG cable to the CSB input. Check that the phase is 180° ±2°.5. Connect the B-probe to L output. If necessary adjust LOWER ANT phaser (PH1) for 0° phase.

6. Connect the cable TEST SIG to the SBO input. If necessary adjust SBO U/L phaser (PH2) to obtain 180° reading at the L output.7. Connect the B-probe to U output. If necessary adjust UPPER ANT phaser (PH3) to obtain 180°. (same phase as in f).

 9 NM 3561 Single antenna system adjustments - MKR9.1 Mechanical alignment9.1.1 Antenna mastUtilise a waterlevel and align the mast vertically by adjustments of the base nuts.9.2 Electrical measurements9.2.1 Antenna return lossUtilise a vector voltmeter or network analyser in a test set-up. Measure return loss for the LPDA.Measure the return loss value for the LPDA including antenna cable.Tolerance: 22 dB minimum.Figure 9-1 Antenna return loss measurement set-up.20dBABVECTOR VOLTMETERDIR. COUPL.Antenna cable under testAntennaFrom MarkerDir. coupler

 10 NM 3562 Dual antenna system adjustments - MKR10.1 Mechanical alignment10.1.1 Antenna mastUtilise a waterlevel and align the mast vertically by adjustments of the base nuts.10.2 Electrical measurements:$51,1*,IWKHDWWHQXDWRUPRGXOHLQWKH0DUNHUXQLWLVFRQILJXUHGIRUG%WKHQWKH5)RXWSXWSRZHULVLQWKHUDQJHRIZDWWV7DNHFDUHRIQRWWRRYHUORDGWKHYHFWRUYROWPHWHUConnect a directional coupler terminated in 50* 10W to the N output connector of the Marker. Then use the forward coupled port as the signal source for the measurements.Always use a 20 dB attenuator at the I/P of the directional coupler in Fig. 1,2 and 3.10.2.1 Antenna cable lengths (Electrical phase equality)Each antenna cable must be electrically measured before the end connector is terminated in the LPDA.Utilise a vector voltmeter or network analyser. Establish antenna cable (A1) return phase as 0° reference phase.Measure return phase for the other antenna cable (A2). Then take into account the phase centres of the LPDA's given in the factory data sheet. Tolerance: ±1.5° true electrical cable length.See measurement set-up diagram Figure 10-1 below: Figure 10-1 Cable phasing measurement set-up.20dBABVECTOR VOLTMETERCABLE UNDER TESTOPEN ENDDIR. COUPL.From MarkerDir. coupler

10.2.2 Monitor return cable lengthMeasure return phase as described in (8.2.1) for both monitor cables. Check that initial val-ues are within ±1.5° true phase (±3.0° return phase).10.2.3 Phase and amplitude transfer measurementConnect each antenna cable and monitor cable to LPDA load and source respectively. Utilise a vector voltmeter or network analyser in a test set-up Figure 10-2, and measure relative transfer phase and amplitude for the antenna cable (A2) in reference to antenna (A1).Figure 10-2 Phase and amplitude transfer measurement set-up.Measure and record phase/amplitude for each antenna. Then determine if one of the monitor cables must be trimmed in order to comply with phase tolerance for the set of cables.Tolerance: ±3°.Amplitude tolerance: ±1.0 dB. If the amplitude tolerance is exceeded something might be wrong in the LPDA monitor circuit or connector/cable. 20dBABVECTOR VOLTMETERA(n)M(n)LPDADIR. COUPL.From MarkerDir. coupler

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.SECTION 4TEST AND ADJUSTEMENTSTable of Contents1 Tests and adjustments LLZ/GP...............................................................................31.1 Configuration Settings........................................................................................31.1.1 ILS Configuration......................................................................................... 31.1.2 Remote Ports Access Level Configuration .................................................. 41.1.3 Warning Configuration ................................................................................. 41.2 Transmitter Alignments and Calibration ............................................................. 41.2.1 RF Phase Feedback Adjustment................................................................. 51.2.2 RF Power..................................................................................................... 61.2.3 LF Phase Adjustment .................................................................................. 61.2.4 RF Power Balance Adjustment.................................................................... 71.2.5 RF Phase at Combiner I/P...........................................................................81.2.6 SDM Calibration...........................................................................................91.2.7 DDM Calibration ..........................................................................................91.2.8 Ident Tone Modulation Depth ......................................................................101.2.9 RF Frequency Adjustment...........................................................................101.3 Antenna System Adjustments ............................................................................101.4 Monitor Alignment and Calibration. ....................................................................111.4.1 General: ....................................................................................................... 111.4.2 RF Input Level Adjustment. .........................................................................111.4.3 AGC Time Adjustment ................................................................................. 121.4.4 SDM Adjustment.......................................................................................... 121.4.5 DDM Adjustment.......................................................................................... 121.5 Monitor Alarm Setting Procedure .......................................................................131.6 Maintenance Limit Adjustments ......................................................................... 141.7 Adjustment points............................................................................................... 152 Tests and adjustments marker beacon ..................................................................192.1 ........................................................................................................................... 192.1.1 Preparations ................................................................................................ 192.1.2 Configuration settings..................................................................................192.2 Adjustment points............................................................................................... 222.3 Adjustments at installation.................................................................................. 232.3.1 Transmitter output power adjustment .......................................................... 232.3.2 Monitor calibration ....................................................................................... 242.4 Other adjustments.............................................................................................. 242.4.1 Output power readout calibration.................................................................242.4.2 Battery protection cut-off voltage ................................................................. 252.4.3 Battery charger voltage................................................................................ 25

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.1 Tests and adjustments LLZ/GP1.1 Configuration Settings Follow this procedure to set the configurations in the ILS according to the desired system con-figuration.1.1.1 ILS ConfigurationSet the correct configuration for this ILS according to this table. The Station Control strap plat-form is located on TCA 1218.Table 1-1 ILS configuration settings.1 Strap IN NOT interlockStrap OUT Interlock2 Strap IN NOT hot standbyStrap OUT Hot standby3 Strap IN 2 frequency ILSStrap OUT 1 frequency ILS4 Strap IN 1 of 2 votingStrap OUT 2 of 2 voting (default)5 Strap IN Lost contact with remote control will NOT turn off transmitters.Strap OUT Lost contact with remote control will turn off transmitters. (default)6Strap IN WRITE DISABLE switch in horizontal position generate service con-dition. (default)Strap OUT WRITE DISABLE switch in horizontal position does not generate ser-vice condition.7Strap IN Grant/deny switch on remote control must be grant position in order to obtain access level 2 or 3 from the RMM system on the remote ports.Strap OUT Grant/deny switch on remote control is overridden.8Strap IN Tells the RMS that this is a GP ILS.Strap OUT Tells the RMS that this is a LLZ ILS.9Strap IN Spare, Not used.Strap OUT Spare, Not used.10 Strap IN Spare, Not used.Strap OUT Spare, Not used.

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6Figure 1-1 Station Control strap platform.1.1.2 Remote Ports Access Level ConfigurationThe allowed access levels on REMOTE ports 1 and 2 on the RMS can be configured by set-ting jumpers on the TCA1218A.Set jumpers in S1 - S4 to configure which access levels that are allowed on remote ports 1 and 2.Jumper in means that access level is allowed.Jumper out means that access level is denied.The table below shows which jumpers are connected to different ports and access levels.Table 1-2 Access level strap settings.1.1.3 Warning ConfigurationUse the RMM Program to configure which warnings shall cause system warning i.e. illuminate the RC main warning lamp.1.2 Transmitter Alignments and CalibrationTEST EQUIPMENT REQUIRED:• Oscilloscope, general purpose• NM 3710 Field Test Set (with 20 dB attenuator)• BNC Test Cable• Frequency Counter RFPORT ACC. LEVEL 2 ACC. LEVEL 3Remote 1 Strap S1 Strap S2Remote 2 Strap S3 Strap S412345678910 HBK592-1

$1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.Carry out the alignment steps in the order outlined below:127(,IVRPHRIWKHIXQFWLRQVSDUDPHWHUVGHSDUWFRQVLGHUDEO\IURPQRUPDOWKHQUHSHDWWKHVWHSVLQVHTXHQFHRQFHPRUHH[FHSWVWHSV127(7KLVDGMXVWPHQWSURFHGXUHDVVXPHVWKDWWKH/3$VDQG*3$V5)OHYHO''0DQG6'0SDUDPHWHUVDUHFRUUHFWO\DGMXVWHG6LWHDGMXVWPHQWVVKRXOGEHOLPLWHGWRVPDOOWRXFKXSDGMXVWPHQWVRQ5)SKDVH5)SKDVHIHHGEDFNDQG5)SRZHUEDODQFH1.2.1 RF Phase Feedback AdjustmentConnect the oscilloscope to the BNC test connector labelled PHASE CORR. located on the transmitter modules.127(6HWWKHVFRSHVLQSXWPRGHWR'&The waveform observed should take a continuous form without limiting segments or deep notches or other dis-continuities.(Each modulator developes it’s own waveform shape due to spreads in insertion phases).The dynamic maximum point should be adjusted to approximately -4 volt.The average operating point of the PHASE CORR. signal can be shifted by means of adjust-ing potentiometer PH.OFFS. at the back of the LPA/GPA.1.2.1 RF Phase Feedback Adjustment1.2.2 RF Power1.2.3 LF Phase Adjustment1.2.4 RF Power Balance Adjustment1.2.5 RF Phase at Combiner I/P1.2.6 SDM Calibration1.2.7 DDM Calibration1.2.7.1 TEST DDM Setting1.2.8 Ident Tone Modulation Depth1.2.9 RF Frequency Adjustment$

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$61.2.2 RF PowerThe CSB and corresponding SBO output power can be adjusted by means of the RMM Pro-gram or the Local Display/Keyboard.Normal operating power level is:The output power can be read by means of the RMM Program or the Local Display/Keyboard.1.2.3 LF Phase Adjustment1.2.3A LF Phase Adjustment (One-frequency system)Connect oscilloscope channel A to the BNC test connector labelled CSB located on LPA/GPA Course 1 (2).Set oscilloscope input mode to DC.Adjust 150 Hz COU phase adj. R3 (LF1223A) observing oscillocope channel A until the waveform equals left hand graph in Figure 1-2.A significant indication of correct LF phase is that the pair of the intermediate peaks are equal in amplitude.Figure 1-3 shows the corresponding SBO waveforms for normal and 10º LF phase error respectively.1.2.3B LF Phase Adjustment (Two-frequency system)Connect oscilloscope channel A to the BNC test connector labelled CSB located on LPA/GPA Course 1 (2).Connect oscilloscope channel B to the BNC test connector labelled CSB located on LPA/GPA Clearance 1 (2).Set oscilloscope input mode to DC. Select CHOP mode.Adjust channel A and B gain so that both waveforms show the same amplitude.By means of the RMM turn off 90 Hz modulation for Course Tx and Clearance Tx.Adjust 150 Hz CLR phase adj. R180 to track 150 Hz Course waveform in the same phase (waveform overlap).LLZ Course 15 W CSBLLZ Clearance 15 W CSBGP Course 5 W CSBGP Clearance 0.5 W CSB

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.By means of the RMM turn on 90 Hz modulation for both Course Tx and Clearance Tx.Adjust 90 Hz COU phase adj. R1 (LF1223A) observing oscillocope channel A until the wave-form equals left hand graph in Figure 1-2.Adjust 90 Hz CLR phase adj. R179 (LF1223A) observing oscillocope channel B until the waveform equals left hand graph in Figure 1-2.A significant indication of correct LF phase is that the pair of the intermediate peaks are equal in amplitude.Figure 1-2 LF phase CSB illustration.Figure 1-3 LF phase SBO illustration.1.2.4 RF Power Balance AdjustmentConnect the oscilloscope to the BNC test connector labelled SBO located on the transmitter modules.127(6HWWKHVFRSHVLQSXWPRGHWR'&'(02'8/$7('&6%1250$/ '(02'8/$7('&6%3+$6((5525'(02'8/$7('6%21250$/ '(02'8/$7('6%23+$6((5525

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6Figure 1-4 Power balance SBO illustration.Perfect power balance between the 90 Hz modulated carrier and the 150 Hz modulated car-rier is indicated when the two largest sets of peak waveforms fall on lines paralell to the base-line.A more accurate way of observing a power balance error is to double the sweep rate in non-trigger mode such that the second 60 Hz half of the cycle is folded back on the first half and tracks the envelope waveform. (Kissing pattern method)RF Power Balance can be adjusted by potentiometer RF-BAL on the back of the LPA/GPA Adjust until both halvs fall on the same envelope waveform or the two largest sets of peak waveforms fall on lines paralell to the baseline.1.2.5 RF Phase at Combiner I/PConnect the oscilloscope to the BNC test connector labelled SBO located on the transmitter modules.127(6HWWKHVFRSHVLQSXWPRGHWR'&Set the oscilloscope in normal trigger mode such that the waveform below can be observed.Figure 1-5 RF phase SBO illustration.'(02'8/$7('6%21250$/ '(02'8/$7('6%2'%32:(5,0%$/$1&(+=+='(02'8/$7('6%21250$/ '(02'8/$7('6%25)3+$6((5525

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.The RF phase (90° start phase) can be adjusted by trimmer RF PHASE on the back of the LPA/GPA.Adjust until the minima points between the smallest peak waveform reach the baseline or a minimum.1.2.6 SDM CalibrationConnect the NM 3710 Field Test Set to the CSB BNC test connector in the Cabinet's Change-over section.(Insert a 20 dB attenuator at the input of the Field Test Set in order to avoid overloading).SDM should be calibrated to 40.0% +/-0.1% SDM by adjusting SDM from the RMM Program or the Local Display/Keyboard.1.2.7 DDM Calibration127(&KHFNWKDWDOO7(67''0VHWWLQJVDUHLQ1250$/Connect the NM 3710 Field Test Set to the CSB BNC test connector in the Cabinet's Change-over section.(Insert a 20 dB attenuator at the input of the Field Test Set in order to avoid overloading).DDM should be calibrated to 0.0% +/-0.05% DDM by adjusting DDM from the RMM Program or the Local Display/Keyboard.1.2.7.1 TEST DDM SettingTEST DDM with 90Hz or 150Hz dominance can be switched on and off from the RMM Pro-gram or the Local Display/Keyboard. The DDM values inserted by TEST DDM are preset val-ues which is set as described below.a) 90 Hz dominance presetUtilise the Field Test Set as in the previous test.Set the TEST DDM in position 90 Hz dominance from the RMM Program or the Local Display/Keyboard. Adjust the (90 Hz) test DDM setting until a wanted DDM value indicating (-) sign is obtained. (Typical value: -0.8%...-1.0% DDM).b) 150 Hz dominance presetUtilise the Field Test Set as in the previous test.Set the TEST DDM in position 150 Hz dominance from the RMM Program or the Local Display/Keyboard. Adjust the (150 Hz) test DDM setting until a wanted DDM value indicating (+) sign is obtained. (Typical value: 0.8%...1.0% DDM).Set the TEST DDM back to normal.

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$61.2.8 Ident Tone Modulation DepthConnect the Field Test Set to the CSB BNC test connector in the Cabinet’s Change-over sec-tion.(Insert a 20 dB attenuator at the input of the Field Test Set in order to avoid overloading).Set the Ident Control to CONTINUOUS from the RMM Program or the Local Display/Key-board.On the Field Test Set, press IDENT.1020 Hz modulation depth can be adjusted from the RMM Program or the Local Display/Key-board.Adjust modulation depth to 10.0% +/-0.3%.An alternative method of checking 1020 Hz modulation depth to 10% is described below:Connect the oscilloscope to the BNC test Connector labelled CSB.Switch off the 90 Hz modulation and the 1020 Hz modulation.Note the peak-to-peak deflection of the remaining 150 Hz waveform.Then switch off the 150 Hz modulation and switch the 1020 Hz modulation to CONTINUOUS.For mod. Depth 10%.The observed 1020 Hz peak-to-peak waveform amplitude should be 50% of the 150 Hz amplitude. 1.2.9 RF Frequency AdjustmentFine-adjustment of the operating frequency can be carried out by adjusting C1 in the OS1221A/B RF Oscillator module.The top cover must be removed.Set the OS1221A/B on an extention board.In order to monitor the frequency, connect the Frequency Counter to the BNC test connector labelled CSB. (Make sure the transmitter under test is routed to Antenna).If necessary for reliable counting switch off modulation tones.Adjust until frequency is less than 1 kHz from operating frequency. Trimmer C1 adjusts course and clearance frequencies simultaneously.1.3 Antenna System AdjustmentsAfter the transmitters has been alligned correctly the antenna system must be alligned. This includes mechanical adjustments of the Antenna System, electrical adjustments (phasing) and adjustments of the ADU and MCU.

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.For details, refer to the adjustment procedure for each antenna system.1.4 Monitor Alignment and Calibration.TEST EQUIPMENT REQUIRED:• Oscilloscope, general purpose• NM 3710 Field Test Set (with 20 dB attenuator)• BNC Test Cable• Digital Voltmeter, 4 digits, DC1.4.1 General:Description is given only for the DS channels. R338++ means that the other channels has numbers R1338, R2338 and R3338 for CL, CLR and NF channels.Before any monitor adjustments are attempted, the following procedures shall be completed:Transmitter calibrationsNetwork alignmentsIt is imperative for the result that the signals from the Monitor Combining Network (MCU) are correct. Check these signals with the NM3710, Field Test Set,It will be these signals which we use for aligning the monitors.1.4.2 RF Input Level Adjustment.Put the MF12xx on an extender card.Turn on the transmitters.Set the potmeter SR338++ in middle position. See Figure 1-6.Figure 1-6 Adjustment points on MF12xx.

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6Adjust the jumper settings in P2++ and potmeters R338++ until the voltage is 240mV at TP23++.Figure 1-7 Alternative jumper settings of P2++.Turn off the equipment and remove the extender card. Set the MF12xx in its correct position.Turn on the transmitters.Adjust the RF level potensiometer on the front of MF12xx until the monitor gives a RF level reading of 3.0V.Repeat above for all monitor channels.1.4.3 AGC Time AdjustmentTurn on the transmitters.Make a note of the AGC voltages on TP 1,2,3 and 4 on MF12xx.Turn off the transmitters.Adjust the AGC TIM potmeter on the front of MF12xx until the AGC voltage (TP1,2,3 or 4) is the same as with a nominal RF input.Do this for all four monitor channels on all of the MF12xx modules in the system.This ensures fast response from the monitors.1.4.4 SDM AdjustmentAdjust the SDM potmeter on the front of MF12xx until the monitors reads 40.0/80.0%SDM +/- 0.1%SDM.1.4.5 DDM AdjustmentMeasure and note down the DDM values from the MCU and NF antenna with help of the Field Test Set.Set the Nominal values for each channel to the measured values with help of the RMM Pro-gram.

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.1.5 Monitor Alarm Setting ProcedureType in the wanted alarm limits from the RMM Program or the Local Display/Keyboard.The monitors will have preset alarm limits when the ILS is delivered for factory.These alarm limits are as listed in the table below:Table 1-3 Localizer alarm limits.*) Only for single frequency ILS. For two frequency ILS the limit is +/- 1dB.CL DS NF CLRDDM 15uA 25uA 15uA 40uACAT I SDM +/- 4% --- --- +/- 4%RF level +/- 3dB*) --- --- +/- 1dBLLZ DDM 11uA 25uA 11uA 40uACAT II SDM +/- 4% --- --- +/- 4%RF level +/- 3dB*) --- --- +/- 1dBDDM 9uA 25uA 9uA 40uACAT III SDM +/- 4% --- --- +/- 4%RF level +/- 3dB*) --- --- +/- 1dB

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6Table 1-4 Glidepath alarm limits.*) Only for single frequency ILS. For two frequency ILS the limit is +/- 1dB.CLR transmitter is only present in two frequency ILS.1.6 Maintenance Limit AdjustmentsUse the RMM Program to set maintenance warning limits in the system. All new systems will have factory preset maintenance warning limits. Maintenance warning limits can not be set from the Local Display/Keyboard.CL DS NF CLRDDM see annex. 1037uA18.5uA 35uA 45uACAT I SDM +/- 5% --- --- +/- 5%RF level +/- 3dB*) --- --- +/- 1dBGP DDM see annex. 1037uA18.5uA 35uA 45uACAT II SDM +/- 5% --- --- +/- 5%RF level +/- 3dB*) --- --- +/- 1dBDDM see annex. 1037uA 35uA 45uACAT III SDM +/- 5% --- --- +/- 5%RF level +/- 3dB*) --- --- +/- 1dB

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.1.7 Adjustment pointsFigure 1-8 Front side adjustment points.11LF 1223AMF 1211AESC PREV NEXT-+ENTERREADQUICKCLRCOAXIALCOURSEMAINPOSITIONWRITEPROTECTWARNINGON/NORMALINTERLOCKOVERRIDEMAINTSTBYOFFREMOTELOCALAUTOMANUALOVERCHANGETX1ALARMSERVICEPARAMDISAGRBATTIDENTTX1TX2TX2STANDBYMon.1 Mon.2Mon.stby.90Hz COU phase adj.150Hz COU phase adj.90Hz CLR phase adj.150Hz CLR phase adj.TX1 TX2NF SDM adj.NF AGC time constant adj.NF RF level adj.CL SDM adj.CL AGC time constant adj.CL RF level adj.CLR SDM adj.CLR AGC time constant adj.CLR RF level adj.DS SDM adj.DS AGC time constant adj.DS RF level adj.Ident mod adj.HBK698-2

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6Figure 1-9 CI1210A Connection Interface adjustment point.TEMPINDOOR TEMPOUTDOOR ACLEVEL ANALOGCH.1 ANALOGCH.2 ANALOGCH.3 DIGITALPORT A DIGITALPORT B DIGITALPORT C DIGITALPORT DTO MB1203RS232 RS232 RS232 REMOTECONTROLDC-LOOP DC-LOOP DMELOCAL REMOTE 2 REMOTE 1 CH.1&2 CH.3&4CI1210ABATTERYWARNINGBattery protection level adj.HBK697-1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.Figure 1-10 Power Amplifier Assembly adjustment points (rear view).PH.OFFS.G150HzRF-BALG90HzDCOSC.SBOCSBFREMDRIFTRF.PHASEPhase feedback offset adj.DC offset adj.RF balance adj.90Hz mod. adj.150 Hz mod. adj.RF phase adj.HBK696-1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.2 Tests and adjustments marker beacon2.12.1.1 PreparationsTerminate the RF OUT terminal with a 50Ω load (antenna or dummy). The transmitters are fac-tory adjusted to 2 watt output power. Let both transmitters run for ½ hour at this power to achieve a stable working temperature before any fine tuning is carried out.2.1.2 Configuration settingsFollow this procedure to set the configurations in the Marker Beacon according to desired sys-tem configuration.2.1.2.1 General ConfigurationThe static control strap on the Connection interface board sets hardware configuration, remote access configuration and shutdown configuration. Figure 2-1 shows where the static control strap is located on CI 1376Figure 2-1 Location of Static Control Strap on CI 1376DIG PORT A DIG PORT B DIG PORT C DIG PORT DCI 1376PB 1378REMOTECONTROLLINETEMPOUTDOORTEMPINDOORAC LEVEL ANA CHA1 ANA CHA2 ANA CHA3REMOTE RMMRS232REMOTE CONTOLRS232CONFIGURATIONS1S2S3S4S5S6S7S8CONFIGURATIONS1S2S3S4S5S6S7S8HBK797/1

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6Set the configuration for the MB according to Table 2-1.Table 2-1 MB Configuration settingsS1 and S3 will decide the model (NM 7050 A, B, C or D) and show up in the Link Status win-dow in the RMM program and the Initial Window in the LCD menu. A disagreement between the settings and the actual number of modules will cause a Maintenance Warning on the Front Panel and an Error in the Maintenance window.With S2 = In the Access Grant switch on the Remote Control will have no effect. You may still acquire access level 2 and 3 on the RMM remote port if the settings of S6 and S7 permits.S4 decides wheather lost communication with the Remote Control will cause shutdown (no TX to air) or not.S5 instructs the transmitter control software weather a failed standby transmitter will be shut down or continue to transmit.S6 and S7 decides the highest access level permitted on the RMM remote port. All access levels are available on the RMM local port regardless of S6 and S7.2.1.2.2 Setting inner, outer or middle markerTo configure the beacon for outer, middle or inner marker set the straps (S1-S4) on the trans-mitter board(s) according to Table 2-2.Strap no State FunctionS1 Strap IN 2 power supplies (NM 7050 B/D)Strap OUT 1 power supply (NM 7050 A/C)S2 Strap IN Access Grant disabledStrap OUT Access Grant enabledS3 Strap IN 2 monitor units (NM 7050 C/D)Strap OUT 1 monitor unit (NM 7050 A/B)S4 Strap IN Lost contact with remote control will NOT cause shutdownStrap OUT Lost contact with remote control will cause shutdownS5 Strap IN Standby transmitter failure will NOTcause shutdownStrap OUT Standby transmitter failure will cause shutdownS6 Strap IN Access level 2 on RMM remote port enabledStrap OUT Access level 2 on RMM remote port disabledS7 Strap IN Access level 3 on RMM remote port enabledStrap OUT Access level 3 on RMM remote port disabledS8 Should always be left open.

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.Table 2-2 Marker function configurationFigure 2-2 shows where the straps are located on the transmitter board(s).Figure 2-2 Location of Marker Beacon type straps on transmitter boardStrap Function when strap is inS1 Beacon is INNER markerS2 Beacon is MIDDLE markerS3 Beacon is OUTER markerS4 Beacon is FAN markerS1S2S3S4TX 1373HBK798/1

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$62.2 Adjustment pointsThe adjustment points are shown in Figure 2-3 Adjustment points and explained below. The figure shows a fully equipped system, NM 7050D, see Section 3 for configuration details:1. Battery charging voltage (nom 27.4V@20°C)2. Bias for power transistor (use factory settings)3. Battery protection cut-off voltage (nom. 22V)4. Tx Detected Rf level (nom. 2.5V@4W carrier)5. Monitor RF level (nom. 3V@nominal output power)6. Monitor frontend input filter centre frequency (use factory settings)7. Real time clock fine tuning(use factory settings)⇒The adjustment points marked Use Factory Settings should not be touched.⇒The baseband level has to be adjusted at installation.⇒The other are factory pre-set but may be adjusted.

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.Figure 2-3 Adjustment points2.3 Adjustments at installationThese procedures have to be carried out at installation in order to set up your equipment right.2.3.1 Transmitter output power adjustmentThis adjustment is most easily done with the RMM PC program but the local keyboard/display may be used.• Make sure the output signal RF OUT is terminated with a 50Ω load (antenna or dummy load).• If this is an Inner Marker make sure the external attenuator (10dB) is installed, inside the Cabinet at the Tx output.• Start the RMM program on the PC (see chapter 10)• Open the TX settings window, RF level for TX1 and TX2 are to be adjusted.• Open the Maintenance window. RF level for TX1 and TX2 are to be watched.•Set Local mode with the Remote/Local switch.•Set Manual mode with the Auto/Manual switch.•Set TX1 to air with the Changeover button•Adjust RF level in TX settings until you read the desired output power on RF level in Main-tenance.ANTISTATShield boxOscillator1234567HBK864/1

1250$5&,167$//$7,21&200,66,21,1*+$1'%22. 1DYLD$YLDWLRQ$6• Check that you read the desired modulation depth in Maintenance.•Set TX2 to air and repeat the two previous steps.2.3.2 Monitor calibrationThe software adjustments are most easily done with the RMM program, but may be carried out from the front panel.• This procedure requires that the output power is already adjusted• Set the input attenuation straps on MO1374 according to the marker type. Start out with 22dB attenuation for outer marker, 18dB for middle marker and 12dB for inner marker.• Watch the Monitor parameter RF level.• Adjust the potentiometer R850 until RF level is 3V at the nominal output power. • (Ref. fig. 2-4)• If this is impossible to achieve, try another strap setting and readjust R850.Figure 2-4 Input Signal attenuator2.4 Other adjustmentsThese adjustments are normally not required, the factory settings should be sufficient.2.4.1 Output power readout calibrationThe Carrier Power parameter in the RMM Maintenance window is the internal wattmeter. It is factory calibrated, but may be recalibrated by following this procedure. The software adjust-ments are most easily done with the RMM program, but may be carried out from the front panel.• Connect a reference wattmeter to the output signal RF OUT. • Set TX1 to air.• Watch the maintenance parameter Carrier Power• Adjust the TX settings parameter RF level until the watt meter shows 2W • Check that the Maintenance parameter Carrier Power on TX1 is accurate to within 5%.0dB6dB12dB16dBMO 137418dB22dBR85028dB34dBHBK799/1

1250$5& 1DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.• If not, adjust the Carrier Power potentiometer on TX1 until the parameter shows 2.00W• Repeat for 1W and 0.5W• Repeat for TX2.2.4.2 Battery protection cut-off voltageThe purpose of this circuit is to avoid deep discharge and thereby reduced life time of the backup battery. For normal lead acid accumulators 22V (1.83V/cell) is a reasonable cut-off voltage.• Turn Off the Mains switch• Connect a DC supply, preadjusted to the desired cut-off (reference) voltage and deacti-vated, to the external charger input on CI 1376. This is called the reference supply.• Connect a multimeter in DC volt position to the battery input.• Turn the reference supply On.• If you measure 0V on the battery adjust the potentiometer on PB1378 until the relay tog-gles and you measure the reference voltage.• If you measure the reference voltage, adjust the potentiometer until the relay disconnects and you measure 0V.2.4.3 Battery charger voltageThe cells of a lead acid battery has an optimal voltage when they are fully charged. This volt-age is greatly dependent on the temperature. The battery life time will decrease if this rule is not followed. To meet the demand, the internal battery charger(s) in NM 7050, the PS 1375, has a temperature compensated charging voltage.Due to current limiting in PS 1375, a discharged battery will firstly be charged with a constant current, ≈2A with one PS1375 and ≈6A with two PS1375. When the battery draws less than the current limit, the battery will be charged with a constant voltage (UBATT). The factory set-ting for the internal battery charger is:UBATT20=27.6V@20°C with This is the normal final voltage for lead acid accumulators. If your batteries require a different final voltage, the adjustment procedure is as follows:• Turn the Battery switch Off and have one TX on .• Measure the environment temperature TENV (in °C)• Compute the temperature deviation ∆T = TENV - 20°C• Compute the new expected final voltage at your environment temperature as • Adjust the potentiometer on PS1375 until you measure UBATT on the 27V test point on CI 1376.⇒Inner Marker uses an external 10 dB attenuator, use 0.2W, 0.1W and 50mW to cali-brate. Carrier Power is measured prior to the attenuator, but the software will automati-cally compensate for the 10dB.k∆UBATT∆T-------------------- 40 mV°C--------–==UU kTBATT BATT=+⋅20 ∆Example:Your battery requires a final voltage of 26V at 20°C, and you have measured an environ-mental temperature of 25°C. You should then adjust the charger to giveUBATT = 26 + (-0.04)(25 - 20) = 25.8V

1250$5& 91DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.SECTION 5GROUND COMMISIONING REFERANCE DOCUMENTSTable of ContentsNM7000 LOCALIZER...........................................................................................2NM7000 GLIDE PATH.........................................................................................11NM7050 MARKER BEACON...............................................................................18

1250$5& 91DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.GROUND COMMISSIONING DOCUMENTNM7000 LOCALIZERAirport RunwayCabinet Serial no.Antenna systemAntenna Distribution Unit (ADU) Serial no.Monitor Distribution Unit (MCU) Serial no.Place: Date:Navia Aviation representative (Sign.) Customer representative (Sign.)

1250$5& 91DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.GENERALThe purpose of this document is to• Ensure that all operating functions are working before the equipment is put into service.• Establish useful reference data and settings for comparisons to routine maintenance data and trouble shooting.REQUIRED TEST EQUIPMENT• Vector voltmeter or Network Analyser• ILS Field Test Set NM3710 with 20 - 30 dB external input attenuator• General purpose Oscilloscope• Frequency Counter, 30 Hz to 350 MHz• Digital Multimeter• Directional Coupler, 75 - 350 MHzDESCRIPTION OF TEST PROCEDURE1.1 - 1.2 , 1.8 - 1.9(COURSE AND CLEARANCE SECTIONS)Connect NM3710 (use external 20-30 attenuator at BNC input) to COURSE RF BNC test point and CLEARANCE RF BNC test point of Cabinet Coaxial section respectively. Use keypad CHANGE OVER to alternate between Tx 1 and Tx 2. Read DDM and SDM.1.3, 1.10(COURSE AND CLEARANCE SECTIONS)Connect the Frequency Counter (use 50Ω input port) to COURSE RF BNC test point and CLEARANCE RF BNC test point of Cabinet Coaxial section respectively. Use keypad CHANGE OVER to alternate between Tx 1 and Tx2.1.4 - 1.5Connect the Frequency Counter (use HI imp. input port) CSB BNC test point on Transmit-ter section LPA1230. Switch off IDENT modulation.90 Hz count: Switch off 150 Hz tone.150 Hz count: Switch on 150 Hz tone and switch off 90 Hz tone.1.6, 1.11Connect the Frequency Counter (use HI imp. input port) CSB BNC test point on Transmit-ter section LPA1230.Switch off 90 and 150 Hz tones. Set the IDENT 1020 Hz to CONTINUOUS. Count the 1020 Hz.1.7, 1.12Connect NM3710 (use external 20-30 attenuator at BNC input) to COURSE RF BNC test point and CLEARANCE RF BNC test point of COA1207A respectively. Push keypad CHANGE OVER to activate the second transmitter. Read IDENT modulation depth.1.13Connect the Digital Multimeter (volts DC) to the BATTERY terminals. (Batteries shall be fully charged). Read the voltage.

$1250$5& 91DYLD$YLDWLRQ$6,167$//$7,21&200,66,21,1*+$1'%22.2.1 - 2.2Connect the NM3710 to the monitor input CL cable (from MCU). Use keypad CHANGE OVER to activate the second transmitter. Read DDM and SDM.2.3 - 2.4Connect the NM3710 to the monitor input DS cable (from MCU). Use keypad CHANGE OVER to activate the second transmitter. Read DDM and SDM.2.5 - 2.6Connect the NM3710 to the monitor input NF cable (from NF antenna). Use keypad CHANGE OVER to activate the second transmitter. Read DDM and SDM.2.7 - 2.8Connect the NM3710 to the monitor input CLR cable (from MCU). Use keypad CHANGE OVER to activate the second transmitter. Read DDM and SDM.3.1 - 3.3Connect the oscilloscope to BNC test points (LPA units) at each relevant Transmitter unit and check that normal waveforms exist.4.1 - 4.7Record all relevant SBO attenuator values obtained from Flight Commissioning Data.4.8 - 4.11Record relevant phaser settings (scale divisions). (4.9 is ADU SBO attenuator setting for NM3522 only.)5.1 - 5.24Fill in phase and amplitude of signals from the receiving end of the monitor cables refer-enced to the input phase/amplitude of the antenna cables. Normalise to A1/M1.Fill in antenna return loss data in column Return loss.6.1 - 6.9Check that all remote control functions are OK.7.1 - 7.6Check that all Slave panel functions are OK.8.1 - 8.2Check that the 90° cable stub and 3 pcs different extension cards exist.9.1 - 9.24Transmitter shall be radiating. Select ILS\Measurements\Monitor II. Disconnect one antenna at a time. Read values (Mon 1,2) for DC LOOP Ø,1,2,3, and record in table. For each disconnected antenna check that one DC LOOP channel for Mon 1 and 2 is in Alarm.10.1Tx 1 operating normal. Make a Station Report to printer or file. Ref. Operator Manual para. 5.4.2.10.2Tx 2 operating normal. Make a Station Report to printer or file. Ref. Operator Manual para. 5.4.2.$