Lelux Electronics LELUX600WR Wireless Door/Window Sensor With Alarm User Manual 615pr

Download:
Mirror Download [FCC.gov]
Document ID	671701
Application ID	+mW9TIUntHkHgLrVkffZvw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	31.07kB (388384 bits)
Date Submitted	2006-06-22 00:00:00
Date Available	2006-06-22 00:00:00
Creation Date	2006-04-14 10:37:35
Document Lastmod	2006-04-14 10:55:04
Document Title	615pr
Document Creator	Adobe Illustrator CS2

INSTALLATION
LEARNING CODE TO MAIN UNIT
1. Remove the screw from the battery compartment cover.(fig.1)
The motion detector sensor compatible T015, T016, T018
main unit, must learn code to main unit then use, learn code
operation see main unit manual.
OPERATION
WIRELESS
DOOR/WINDOW
SENSOR WITH ALARM
(fig.1)
2. Install an alkaline 9V battery.
3. Replace the battery cover and screw.
4. Mount the magnetic door/window sensor
Choose a suitable location, then use the template provided in
the last page of manual, mark locations to drill holes and install
anchors and screws. Place the unit over the screws and slide it
down to secure in place. (fig.2)
BATTERY LOW INDICATOR
When 9V battery goes low, the LED will light on 3 seconds and
off 1 second, change a new alkaline 9V battery immediately, or the
sensor might not detection properly.
Warning:
Changes or modifications to this unit not expressly approved by
the party responsible for compliance will void the user's authority to
operate the equipment. Any change to the equipment will void FCC
grant.
ALARM
ON
OFF
(Fig.2a)
(Fig.2b)
5． Mount the magnetic wired piece to the door or window frame
and another single piece to the door/window by using the doubleside tapes (included) and aligned the 2 sensor pieces to be
flushed and “arrow” facing “arrow” at no more than1/4” apart as
shown in (fig.3)
arrow facing arrow
(Fig.3)
OWNER'S MANUAL
After 60 seconds installed 9V battery, the unit will into standby
mode. Once the door/window opened or the unit vibration will
output wireless radio signal and LED flash, then sound alarm 3
seconds, you can turn alarm switch select on or off.
NOTE: After select a location, you should test the sensor transmitting range before mount it permanently, turn local alarm switch to
OFF , turn the CHIME switch to ON of T015, T016 main unit or
press HOME button of T018 main unit, then open/close the
magnetic switch of door/window sensor to trigger, you will hear
the main unit sounds “DING DONG” chime if signal is received
successfully, if not, change location is required.
-1-
This equipment has been tested and found to comply with the
limits for a Class C digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
-2-

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1.1-111
Format                          : application/pdf
Title                           : 615pr
Creator Tool                    : Adobe Illustrator CS2
Create Date                     : 2006:04:14 10:37:35+08:00
Modify Date                     : 2006:04:14 10:55:04+08:00
Metadata Date                   : 2006:04:14 10:55:04+08:00
Thumbnail Width                 : 256
Thumbnail Height                : 168
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 17549 bytes, use -b option to extract)
Document ID                     : uuid:46FAA66057CBDA1193539BE1AF2BAF2A
Instance ID                     : uuid:bebbe0f7-dc97-4b7b-91f2-34b52a0e0f02
Derived From Instance ID        : uuid:45FAA66057CBDA1193539BE1AF2BAF2A
Derived From Document ID        : uuid:C3A45DCB4ACBDA1193539BE1AF2BAF2A
Page Count                      : 1
Creator Version                 : 12
Container Version               : 9
Creator                         : Adobe Illustrator(R) 12.0
For                             : User, -g
Bounding Box                    : -14 33 729 521

EXIF Metadata provided by EXIF.tools