Lenovo Ideapad 130 HMM Hardware Maintenance Manual 14IKB, 15IKB 14IKB Laptop (ideapad) Type 81H6 15ast 201805

2018-05-24

User Manual: Lenovo Hardware Maintenance Manual - 130-14IKB, 130-15IKB 130-14IKB Laptop (ideapad) - Type 81H6 81H6

Open the PDF directly: View PDF .
Page Count: 74

Download
Open PDF In Browser	View PDF

Lenovo ideapad 130
Hardware
Maintenance
Manual

Notes:
• Before using this information and the product it supports, be sure to read the general information under
“Notices” on page 69.
• This manual applies to the following models: Lenovo ideapad 130-14IKB/ideapad 130-15IKB/
ideapad 130-15AST.
The illustrations used in this manual are for Lenovo ideapad 130-15AST unless otherwise stated.

First Edition (May. 2018)
© Copyright Lenovo 2018. All rights reserved.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General
Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set
forth in Contract No. GS-35F-05925.
© 2018 Lenovo

Contents
About this manual........................................ iv
Safety information......................................... 1
General safety................................................. 2
Electrical safety............................................... 3
Safety inspection guide................................... 5
Handling devices that are sensitive to
electrostatic discharge..................................... 6
Grounding requirements.................................. 6
Safety notices: multilingual translations.......... 7
Laser compliance statement......................... 14
Important service information.................... 16
Strategy for replacing FRUs.......................... 16
Strategy for replacing a hard disk drive.............17
Important notice for replacing a system board ........17

Important information about replacing RoHS
compliant FRUs............................................. 18
General checkout ....................................... 19
What to do first.............................................. 20
Power system checkout................................ 21

1070 ODD board...............................................41
1080 Fan and heat sink assembly.....................42
1090 Speaker....................................................45
1100 RTC battery...............................................46
1110 System board............................................. 47
1120 Upper case................................................49
1130 LCD unit....................................................50
1140 EDP cable and integrated camera............52
1150 LCD hinges...............................................54

Locations....................................................... 55
Front and right-side view...................................55
Bottom and left-side view .................................56

Parts list......................................................... 57

Overall...............................................................58
LCD FRUs.........................................................64
Miscellaneous parts...........................................66
AC adapters.......................................................67
Screws...............................................................68

Notices......................................................... 69
Trademarks................................................... 70

Checking the AC adapter ..................................21
Checking operational charging..........................22
Checking the battery pack.................................22

Related service information....................... 23
Restoring the factory contents by using
recovery system............................................ 23

Restore of factory default..................................23

Passwords..................................................... 24
Power-on password...........................................24
Hard-disk password...........................................24
Administrator password.....................................24

Power management...................................... 25

Putting the computer to sleep or shutting it down......25
Putting your computer to sleep..........................25
Shutting down the computer..............................25

Lenovo ideapad 130.................................... 26
Specifications................................................ 26
Status indicators............................................ 28
Setting hotkey mode..........................................29

Fn key combinations/Hotkeys....................... 29
FRU replacement notices.............................. 30

Screw notices ...................................................30

Removing and replacing an FRU.................. 31

1010 Optical drive..............................................32
1020 Base cover................................................33
1030 Battery pack..............................................35
1040 Hard disk drive..........................................36
1050 DIMM........................................................38
1060 PCI Express Mini Card for wireless LAN........39

iii

About this manual
This manual contains service and reference information for the following
Lenovo products:
Lenovo ideapad 130-14IKB/ideapad 130-15IKB/ideapad 130-15AST
Use this manual to troubleshoot problems.
The manual is divided into the following sections:
• The common sections provide general information, guidelines, and safety
information required for servicing computers.
• The product-specific section includes service, reference, and product-specific
parts information.

Important:
This manual is intended only for trained servicers who are familiar with Lenovo
products. Use this manual to troubleshoot problems effectively.
Before servicing a Lenovo product, make sure to read all the information under
“Safety information” on page 1 and “Important service information” on page 16.

Safety information

Safety information
This chapter presents the following safety information that you need to get
familiar with before you service a Lenovo ideapad 130-14IKB/
ideapad 130-15IKB/ideapad 130-15AST computer:
• “General safety” on page 2
• “Electrical safety” on page 3
• “Safety inspection guide” on page 5
• “Handling devices that are sensitive to electrostatic discharge” on page 6
• “Grounding requirements” on page 6
• “Safety notices: multilingual translations” on page 7
• “Laser compliance statement” on page 14

Lenovo ideapad 130 Hardware Maintenance Manual
General safety
Follow these rules below to ensure general safety:
• Observe a good housekeeping in the area where the machines are put
during and after the maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt
to lift it.
4. Lift it by standing or pushing up with your leg muscles; this action could
avoid the strain from the muscles in your back. Do not attempt to lift any
object that weighs more than 16 kg (35 lb) or that you think is too heavy
for you.
• Do not perform any action that causes hazards to the customer, or that
makes the machine unsafe.
• Before you start the machine, make sure that other service representatives
and the customer are not in a hazardous position.
• Please remove covers and other parts in a safe place, away from all
personnel, while you are servicing the machine.
• Keep your toolcase away from walk areas so that other people will not trip
over it.
• Do not wear loose clothing that can be trapped in the moving parts of the
machine. Make sure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with the
nonconductive clip, about 8 centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for
your clothing.
Attention: Metal objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting
wire, attaching springs, using solvents, or working in any other conditions
that may be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent the overheating of internal
components. Do not obstruct fan louvers or cover them with labels or
stickers.

Safety information

Electrical safety
Observe the following rules when working on electrical equipments.

Important:
Use only approved tools and test equipments. Some hand tools have handles
covered with a soft material that does not insulate you when working with live
electrical currents.
Many customers have rubber floor mats near their machines that contain small
conductive fibers to decrease electrostatic discharges. Do not use such kind of mat
to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting switch or
electrical outlet. If an electrical accident occurs, you can then operate the
switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near the equipment that
has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you
cannot unplug it, ask the customer to power-off the wall box that supplies
power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits,
observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near
you.
Attention: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete
circuit. By observing the above rule, you may prevent a current from
passing through your body.
– When using testers, set the controls correctly and use the approved
probe leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate
you from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages;
instructions for these precautions are in the safety sections of maintenance
information. Be extremely careful when you measure the high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational
condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check
it to make sure that it has been powered off.

Lenovo ideapad 130 Hardware Maintenance Manual
• Always look carefully for possible hazards in your work area. Examples of
these hazards are moist floors, nongrounded power extension cables, power
surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic
dental mirror. The surface is conductive; such touching can cause personal
injury and machine damage.
• Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
• If an electrical accident occurs:
– Caution: do not become a victim yourself.
– Switch off the power.
– Send the victim to get medical aid.

Safety information

Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potential
unsafe conditions. As each machine was designed and built, required safety
items were installed to protect users and service personnel from injury. This
guide addresses only those items. You should use good judgment to identify
potential safety hazards according to the attachment of non-Lenovo features or
options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the
apparent hazard could be and whether you can continue without first correcting
the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame
can cause serious or fatal electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potential unsafe conditions, use the
following checklist at the beginning of every service task. Begin the checks with
the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Turn off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo alterations. Use good judgment as to the
safety of any non-Lenovo alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal
filings, contamination, water or other liquids, or signs of fire or smoke
damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not
been removed or tampered with.

Lenovo ideapad 130 Hardware Maintenance Manual
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD). ESD damage can occur
when there is a difference in charge between objects. Protect against ESD
damage by equalizing the charge so that the machine, the part, the work mat,
and the person handling the part are all at the same charge.

Notes:
1. Use product-specific ESD procedures when they exceed the requirements
noted here.
2. Make sure that the ESD protective devices you use have been certified
(ISO 9000) as fully effective.

When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your
body.
• Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
• Use the black side of a grounded work mat to provide a static-free work
surface. The mat is especially useful when handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection
that meets the specific service requirement.

Note:
The use of a grounding system to guard against ESD damage is desirable but not
necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or greenwire ground.
– When working on a double-insulated or battery-operated system, use an
ESD common ground or reference point. You can use coax or connectoroutside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements
Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.

Safety information

Safety notices: multilingual translations
The safety notices in this section are provided in English, French, German,
Hebrew, Italian, Japanese, and Spanish.

Safety notice 1
Before the computer is powered on after FRU replacement, make sure all screws,
springs, and other small parts are in place and are not left loose inside the
computer. Verify this by shaking the computer and listening for rattling sounds.
Metallic parts or metal flakes can cause electrical shorts.
Avant de remettre l’ordinateur sous tension après remplacement d’une unité en
clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et
bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect
ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer
un court-circuit.
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird,
muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile
fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf
Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse
erzeugen.

Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una
FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni
siano nella corretta posizione e non siano sparse all’interno dell’elaboratore.
Verificare ciò scuotendo l’elaboratore e prestando attenzione ad eventuali rumori;
eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi.

Antes de encender el sistema despues de sustituir una FRU, compruebe que
todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio
y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema
y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden
causar cortocircuitos eléctricos.

Lenovo ideapad 130 Hardware Maintenance Manual

Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and cadmium. Do not
disassemble a standby battery, recharge it, throw it into fire or water, or shortcircuit it. Dispose of the battery as required by local ordinances or regulations.
Use only the battery in the appropriate parts listing. Use of an incorrect battery can
result in ignition or explosion of the battery.
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les
démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne
les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle
de l’horloge temps réel, veillez à n’utiliser que les modèles cités dans la liste de
pièces détachées adéquate. Une batterie ou une pile inappropriée risque de prendre
feu ou d’exploser.
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet,
kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden.
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden,
der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu
Entzündung oder Explosion führen.

Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio.
Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle.
Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e
disposizioni locali). Quando si sostituisce la batteria dell’RTC (real time clock) o
la batteria di supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo
parti. L’impiego di una batteria non adatta potrebbe determinare l’incendio o
l’esplosione della batteria stessa.

Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio.
No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.
Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.

Safety information

Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not disassemble it, throw
it into fire or water, or short-circuit it. Dispose of the battery pack as required by
local ordinances or regulations. Use only the battery in the appropriate parts listing
when replacing the battery pack. Use of an incorrect battery can result in ignition
or explosion of the battery.
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser
que les modèles cités dans la liste de pièces détachées adéquate. En effet, une
batterie inappropriée risque de prendre feu ou d’exploser.
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden.
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste
aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion
führen.

La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco
o nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR
915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la
batteria, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego
di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della
batteria stessa.

Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni
recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como
dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de
piezas al sustituir la batería. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.

Lenovo ideapad 130 Hardware Maintenance Manual

Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a severe burn. Do not
recharge it, remove its polarized connector, disassemble it, heat it above 100°C
(212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as
required by local ordinances or regulations. Use only the battery in the appropriate
parts listing. Use of an incorrect battery can result in ignition or explosion of the
battery.
La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie,
d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son
connecteur polarisé et ne la démontez pas. Ne l’exposez pas à une temperature
supérieure à 100°C, ne la faites pas brûler et n’en exposez pas le contenu à l’eau.
Mettez la pile au rebut conformément à la réglementation en vigueur. Une pile
inappropriée risque de prendre feu ou d’exploser.
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren
oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht
aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr
Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung
angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen
Bestimmungen für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien
des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher
Batterien kann zu Entzündung oder Explosion führen.

La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o
procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato,
smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi,
incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR
915/82, successive disposizioni e disposizioni locali). L’impiego di una batteria
non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.

La batería de repuesto es una batería de litio y puede provocar incendios,
explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado,
ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la incinere ni
exponga el contenido de sus celdas al agua. Deséchela tal como dispone la
normativa local.

Safety information

Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your
hands, immediately wash the affected areas with water at least for 15 minutes.
Seek medical care if any symptoms caused by the fluid are present after washing.
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les
yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au
moins quinze minutes. Consultez un médecin si des symptômes persistent après le
lavage.
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung
die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm
besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird
oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und
die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten
die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei
Beschwerden anschließend ein Arzt aufgesucht werden.

Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto
entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti
interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i
sintomi dovessero permanere.

Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus
manos, lave inmediatamente las áreas afectadas con agua durante 15 minutos
como mínimo. Obtenga atención medica si se presenta algún síntoma del fluido
despues de lavarse.

Lenovo ideapad 130 Hardware Maintenance Manual

Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects the lower part of the
inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique
protégeant la partie inférieure de la carte d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der
Spannungswandlerplatine umgibt, nicht entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la
parte inferiore della scheda invertitore.

Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la
tarjeta invertida.

Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or grounded battery can
produce enough current to burn personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la
mise à la masse d’une batterie peut produire suffisamment de courant pour brûler
des matériaux combustibles ou causer des brûlures corporelles graves.
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu
entzünden oder Verletzungen bei Personen hervorzurufen.

Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in
corto circuito o a massa può fornire corrente sufficiente da bruciare materiali
combustibili o provocare ustioni ai tecnici di manutenzione.

Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada
o con contacto a tierra puede producir la corriente suficiente como para quemar
material combustible o provocar quemaduras en el personal.

Safety information

Safety notice 8
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any interconnecting
cables.
Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension,
débranchez tous les cordons d’alimentation des socles de prise de courant, retirez
la batterie et déconnectez tous les cordons d’interface.
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen,
der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU
entfernt wird.

Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese
elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi
di interconnessione.

Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de
las tomas de corriente eléctrica, quite la batería y, a continuación, desconecte
cualquier cable de conexión entre dispositivos.

Lenovo ideapad 130 Hardware Maintenance Manual
Laser compliance statement
Some models of Lenovo computer are equipped from the factory with an
optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such
devices are also sold separately as options. If one of these drives is installed,
it is certified in the U.S. to conform to the requirements of the Department of
Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR)
Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to
conform to the requirements of the International Electrotechnical Commission
(IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note
the following:

CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles
aqui especificados pode resultar em perigosa exposição à radiação.
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de
réglage et d’utilisation des commandes, ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann
gefährliche Laserstrahlung auftreten.
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle
specificate possono provocare l’esposizione a.

El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí
especificados puede provocar la exposición a radiaciones peligrosas.
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage
device could result in exposure to hazardous laser radiation. There are no
serviceable parts inside those drives. Do not open.

Safety information

A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may
contain an embedded Class 3A or Class 3B laser diode. Note the following:

DANGER
Emits visible and invisible laser radiation when open. Do not stare into the beam,
do not view directly with optical instruments, and avoid direct exposure to the
beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente
por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder
directement avec des instruments optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente
in den Laserstrahl sehen und den Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai
eszközökkel. Kerülje a sugárnyalábbal való érintkezést!
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non
guardarlo direttamente con strumenti ottici e evitare l’esposizione diretta al fascio.

Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el
haz de luz. Evite la exposición directa al haz.

Lenovo ideapad 130 Hardware Maintenance Manual

Important service information
This chapter presents the following important service information:
• “Strategy for replacing FRUs” on page 16
– “Strategy for replacing a hard disk drive” on page 17
– “Important notice for replacing a system board” on page 17
• “Important information about replacing RoHS compliant FRUs” on page 18

Important:
BIOS and device driver fixes are customer-installable. The BIOS and device drivers
are posted on the customer support site:
http://support.lenovo.com.

Strategy for replacing FRUs
Before replacing parts:
Make sure that all software fixes, drivers, and BIOS downloads are installed
before replacing any FRUs listed in this manual.
After a system board is replaced, ensure that the latest BIOS is loaded to the
system board before completing the service action.
To download software fixes, drivers, and BIOS, follow the steps below:
1. Go to http://support.lenovo.com.
2. Enter the serial number or select a product or use Lenovo smart
downloading.
3. Select the BIOS/Driver/Applications and download.
4. Follow the directions on the screen and install the necessary software.

Important service information

Use the following strategy to prevent unnecessary expense for replacing and
servicing FRUs:
• If you are instructed to replace an FRU, but the replacement does not solve
the problem, reinstall the original FRU before you continue.
• Some computers have both a processor board and a system board. If you
are instructed to replace either of them, and replacing one of them does not
solve the problem, reinstall that board, and then replace the other one.
• If an adapter or a device consists of more than one FRU, any of the FRUs
may be the cause of the error. Before replacing the adapter or device,
remove the FRUs one by one to see if the symptoms change. Replace only
the FRU that changed the symptoms.
Attention: The setup configuration on the computer you are servicing may
have been customized. Running Automatic Configuration may alter the
settings. Note the current configuration settings (using the View Configuration
option); then, when service has been completed, verify that those settings
remain in effect.

Strategy for replacing a hard disk drive
Always try to run a low-level format before replacing a hard disk drive. This
will cause all customer data on the hard disk to be lost. Make sure that the
customer has a current backup of the data before performing this action.
Attention: The drive startup sequence in the computer you are servicing may
have been changed. Be extremely careful during write operations such as
copying, saving, or formatting. If you select an incorrect drive, data or programs
can be overwritten.

Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper
handling can cause damage to those components, and may cause a system
malfunction.
Attention: When handling a system board:
• Do not drop the system board or apply any excessive force to it.
• Avoid rough handling of any kind.
• Avoid bending the system board and hard pushing to prevent cracking at
each BGA (Ball Grid Array) chipset.

Lenovo ideapad 130 Hardware Maintenance Manual
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and
Electronic Equipment Directive (2002/95/EC) is a European Union legal
requirement affecting the global electronics industry. RoHS requirements
must be implemented on Lenovo products placed on the market after
June 2006. Products on the market before June 2006 are not required to
have RoHS compliant parts. If the original FRU parts are non-compliant,
replacement parts can also be non-compliant. In all cases if the original
FRU parts are RoHS compliant, the replacement part must also be RoHS
compliant.
Note: RoHS and non-RoHS FRU part numbers with the same fit and function
are identified with unique FRU part numbers.
Lenovo plans to transit to RoHS compliance well before the implementation
date and expects its suppliers to be ready to support Lenovo’s requirements
and schedule in the EU. Products sold in 2005 and 2006 will contain some
RoHS compliant FRUs. The following statement pertains to these products and
any product Lenovo produces containing RoHS compliant FRUs.
RoHS compliant FRUs have unique FRU part numbers. Before or after the
RoHS implementation date, failed RoHS compliant parts must always be
replaced with RoHS compliant ones, so only the FRUs identified as compliant
in the system HMM or direct substitutions for those FRUs may be used.
Products marketed before June 2006

Products marketed after June 2006

Current or
original part

Replacement FRU Current or
original part

Non-RoHS

Can be Non-RoHS

Non-RoHS

Can be RoHS

Non-RoHS

Can sub to RoHS

RoHS

Must be RoHS

Replacement FRU

Must be RoHS

Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of the order.

General checkout

General checkout
This chapter presents the following information:
• “What to do first” on page 20
• “Power system checkout” on page 21
Before you go to the checkout, make sure to read the following important notes:

Important notes:
• Only certified trained personnel can service the computer.
• Before replacing any FRU, read the entire page on removing and replacing
FRUs.
• Carefully remove screws for reuse when replacing FRUs.
• Be extremely careful during such write operations as copying, saving, or
formatting. Drives in the computer that you are servicing sequence might
have been altered. If you select an incorrect drive, data or programs might be
overwritten.
• Replace an FRU only with another FRU of the correct model. When you
replace an FRU, make sure that the machine model and the FRU part number are
correct by referring to the FRU parts list.
• An FRU should not be replaced just because of a single, unreproducible failure.
Single failures can occur for a variety of reasons that have nothing to do with a
hardware defect, such as cosmic radiation, electrostatic discharge, or software
errors. Consider replacing an FRU only when a problem recurs. If you suspect that
an FRU is defective, clear the error logs and run the test again. If the error does
not recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.

Lenovo ideapad 130 Hardware Maintenance Manual
What to do first
When you do return an FRU, you must include the following information in the
parts exchange form or parts return form that you attach to it:
1. Name and phone number of servicer
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Procedure index and page number in which the failing FRU was detected
6. Failing FRU name and part number
7. Machine type, model number, and serial number
8. Customer’s name and address
Note for warranty: During the warranty period, the customer may be
responsible for repair costs if the computer damage was caused by misuse,
accident, modification, unsuitable physical or operating environment, or
improper maintenance by the customer.
The following is a list of some common items that are not covered under
warranty and some symptoms that might indicate that the system was
subjected to stress beyond normal use.
Before checking problems with the computer, determine whether the damage is
covered under the warranty by referring to the following list:
The following are not covered under warranty:
• LCD panel cracked from the application of excessive force or from being
dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken
by excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a PC Card or the installation of
an incompatible card
• Improper disk insertion or use of an optical drive
• Diskette drive damage caused by pressure on the diskette drive cover,
foreign material in the drive, or the insertion of a diskette with multiple labels
• Damaged or bent diskette eject button
• Fuses blown by attachment of a nonsupported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect AC adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted
activities:
• Missing parts might be a symptom of unauthorized service or modification.
• If the spindle of a hard disk drive becomes noisy, it may have been subjected
to excessive force, or dropped.

General checkout

Power system checkout
To verify a symptom, follow the steps below:
1. Turn off the computer.
2. Remove the battery pack.
3. Connect the AC adapter.
4. Make sure that power is supplied when you turn on the computer.
5. Turn off the computer.
6. Disconnect the AC adapter and install the charged battery pack.
7. Make sure that the battery pack supplies power when you turn on the
computer.
If you suspect a power problem, see the appropriate one of the following power
supply checkouts:
• “Checking the AC adapter” on page 21
• “Checking operational charging” on page 22
• “Checking the battery pack” on page 22

Checking the AC adapter
You are here because the computer fails only when the AC adapter is used.
• If the power-on indicator does not turn on, check the power cord of the AC
adapter for correct continuity and installation.
• If the computer does not charge during operation, go to “Checking
operational charging”.
To check the AC adapter, follow the steps below:
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the AC adapter cable. See the
following figure:

Voltage (V DC)

+20

2
2
1

Note: Output voltage for the AC adapter pin No. 2 may differ from the one you
are servicing.
3. If the voltage is not correct, replace the AC adapter.
4. If the voltage is acceptable, do the following:
• Replace the system board.
• If the problem persists, go to “Lenovo ideapad 130” on page 26.
Note: Noise from the AC adapter does not always indicate a defect.

Lenovo ideapad 130 Hardware Maintenance Manual
Checking operational charging
To check whether the battery charges properly during operation, use a
discharged battery pack or a battery pack that has less than 50% of the total
power remaining when installed in the computer.
Perform operational charging. If the battery status indicator or icon does not
light on, remove the battery pack and let it return to room temperature. Reinstall
the battery pack. If the charge indicator or icon is still off, replace the battery
pack.
If the charge indicator still does not light on, replace the system board. Then
reinstall the battery pack. If it is still not charged, go to the next section.

Checking the battery pack
Battery charging does not start until the Power Meter shows that less than 95%
of the total power remains; under this condition the battery pack can charge to
100% of its capacity. This protects the battery pack from being overcharged or
from having a shortened life.
To check your battery, move your cursor to the Power Meter icon in the icon
tray of the Windows® taskbar and wait for a moment (but do not click it), and the
percentage of battery power remaining is displayed. To get detailed information
about the battery, double-click the Power Meter icon.
Note: If the battery pack becomes hot, it may not be able to be charged.
Remove it from the computer and leave it at room temperature for a while. After
it cools down, reinstall and recharge it.

Related service information

Related service information
This chapter presents the following information:
• “Restoring the factory contents by using recovery system” on page 23
• “Passwords” on page 24
• “Power management” on page 25

Restoring the factory contents by using recovery system
Restore of factory default
The Lenovo ideapad 130-14IKB/ideapad 130-15IKB/ideapad 130-15AST
computers come with pre-installed recovery system. In order to save
application files and the initial backed up files of the system, the hard disk in
a Lenovo computer includes a hidden partition when it is shipped. If you need
to restore the system to the point of your first boot up, just enter the recovery
system. For details of the Recovery system, see the User Guide for Recovery
system.
Note: This will delete all the new data on the system partition (C drive), which
is not recoverable. Make sure to back up your critical data before you perform this
action.

Lenovo ideapad 130 Hardware Maintenance Manual
Passwords
As many as three passwords may be needed for any Lenovo computer:
the power-on password (POP), the hard disk password (HDP), and the
administrator password.
If any of these passwords has been set, a prompt for it appears on the screen
whenever the computer is turned on. The computer does not start until the
password is entered.

Power-on password
A power-on password (POP) protects the system from being powered on by
an unauthorized person. The password must be entered before an operating
system can be booted.

Hard-disk password
There are two hard-disk passwords (HDPs):
+ User HDP - for the user
+ Master HDP - for the system administrator, who can use it to get access to
the hard disk drive even if the user has changed the user HDP
Attention: If the user HDP has been forgotten, check whether a master HDP
has been set. If it has, it can be used for access to the hard disk drive. If
no master HDP is available, neither Lenovo nor Lenovo authorized service
technicians provide any services to reset either the user or the master HDP, or
to recover data from the hard disk drive. The hard disk drive can be replaced
for a scheduled fee.

Administrator password
Administrator password controls the access of the whole setup utility. Only
Administrator password was set then User password can be set. If Administrator
password was cleared, the User password was cleared too.

Related service information

Power management
Note: Power management modes are not supported for APM operating system.

Putting the computer to sleep or shutting it down
When you have finished working with your computer, you can put it to sleep or
shut it down.

Putting your computer to sleep
If you will be away from your computer for only a short time, put the computer to
sleep. When the computer is in sleep mode, you can quickly wake it to resume use,
bypassing the startup process.
To put the computer to sleep, do one of the following:
• Close the display lid.
• Press the Power button.
• Open the start menu, and then select Power

→ Sleep.

Attention: Wait until the power indicator light starts blinking (indicating that
the computer is in sleep mode) before you move your computer. Moving your
computer while the hard disk is spinning can damage the hard disk, causing
loss of data.
To wake the computer, do one of the following:
• Press any key on the keyboard.
• Press the Power button.

Shutting down the computer
If you are not going to use your computer for a long time, shut it down.
To shut down the computer, do one of the following:
• Open the start menu, and then select Power

→ Shut down.

• Right-click the Start button in the lower-left corner and select Shut down or
sign out → Shut down.

Lenovo ideapad 130 Hardware Maintenance Manual

Lenovo ideapad 130
This chapter presents the following product-specific service references and
product-specific parts information:
• “Specifications” on page 26
• “Status indicators” on page 28
• “Fn key combinations/Hotkeys” on page 29
• “FRU replacement notices” on page 30
• “Removing and replacing an FRU” on page 31
• “Locations” on page 55
• “Parts list” on page 57

Specifications
The following table lists the specifications of the
Lenovo ideapad 130-14IKB/ideapad 130-15IKB/ideapad 130-15AST:
Table 1. Specifications
Feature

Description

Processor

• View the system properties of your computer.
You can do this as follows: Open the Control Panel, and then
select System and Security → System.
• Integrated graphics: Depends on CPU
• Discreted graphics:
NV LV1-N16V-GMR1(For i3, i5/i7) (Lenovo ideapad 130-14IKB/
Lenovo ideapad 130-15IKB)
AMD LV2-R17M-M1-70 (Lenovo ideapad 130-15AST)
• 14.0" 16:9, 1,366 X 768 pixels HD / 1,920 x 1,080 pixels FHD
(Lenovo ideapad 130-14IKB)
15.6" 16:9, 1,366 X 768 pixels HD / 1,920 x 1,080 pixels FHD
(Lenovo ideapad 130-15IKB/Lenovo ideapad 130-15AST)
• DDR4-2133 MHz, SODIMM × 1, on board × 1 (max 4 GB (on
board) + 8 GB)(Lenovo ideapad 130-14IKB/
Lenovo ideapad 130-15IKB)
DDR4-2133 MHz (Lenovo ideapad 130-15AST depending on
configuration), SODIMM × 1 (max 8 GB)
(Lenovo ideapad 130-15AST)
• HDD: 2.5-inch, 7.0 mm SATA II/SATA III
• SSD: 128 GB / 256 GB, SATA III
(Lenovo ideapad 130-14IKB/Lenovo ideapad 130-15IKB)
128 GB, SATA III (Lenovo ideapad 130-15AST)

Graphic memory
chip

Display

Standard
memory

Storage devices

Lenovo ideapad 130

Table 1. Specifications (continued)
Feature

Description

Optical drive
I/O port

•
•
•
•
•
•
•
•

Audio
Bluetooth
wireless
Keyboard
Integrated
camera
Battery

AC adapter
Pre-installed
operating
system

9.0 mm, Rambo
USB 3.0 × 2
Combo audio jack × 1
HDMI port × 1
RJ-45 × 1
Memory card slot (SD/SDHC/SDXC/MMC)
3.5 mm Combo audio jack
1.5 W speaker × 2

• Combined in combo card
• 6 rows Lenovo Keyboard
• HD
• Li-ion battery pack
2 cells, 30 Wh / 35 Wh (Lenovo ideapad 130-14IKB/
Lenovo ideapad 130-15IKB)
2 cells, 30 Wh (Lenovo ideapad 130-15AST)
• 20 V DC, UMA 45 W, DIS 65 W
• Win 10 64bits
• Free-DOS

Lenovo ideapad 130 Hardware Maintenance Manual
Status indicators
The system status indicators below show the computer status:

Table 2. Status indicators
Symbol Indicator

Power

Indicator
status
On
(solid
white)

Charge
status
---

The computer is powered on.

Blinking

---

The computer is in sleep mode.

Off

---

The computer is powered off.

On
(solid
white)
On
(solid
amber)

Battery

Blinking
slowly
(white)
Blinking
slowly
(amber)
Blinking
quickly
(amber)
Off

Charging
Discharging

Charging

Meaning

The battery has more than 80% charge,
charging will continue until the battery is
fully charged.
The battery has between 5% and
20% charge.
The battery has between 20% and
80% charge. When the battery
reaches 80% charge, the light will
stop blinking. However, charging
will continue until the battery is fully
charged.
The battery is being charged. When
battery charge reaches 20%, the
blinking color changes to white.

Discharging

The battery has between 1% and 5%
charge.

Discharging

The computer is in sleep mode or
turned off; the battery has more than
20% charge.

Lenovo ideapad 130

Fn key combinations/Hotkeys
You can access certain system settings quickly by pressing the appropriate
hotkeys.
Table 3. Hotkeys
:

Mutes/unmutes the sound.

Enables/disables Airplane
mode.

Decreases the volume level.

Enables/disables the
integrated camera.

Increases the volume level.

Locks the screen.

Enables/disables the
microphone.

Toggles the display between
the computer and an external
device.

Refreshes the desktop or the
currently active window.

Decreases the display
brightness.

Enables/disables the
touchpad.

Increases the display
brightness.

Setting hotkey mode
By default, the hotkey functions are accessible by pressing the appropriate
hotkey. However, you can disable the hotkey mode in the BIOS setup utility.
To disable the hotkey mode:
1. Shut down the computer.
2. Press the Novo button and then select BIOS Setup.
3. In the BIOS setup utility, open the Configuration menu, and change the
setting of HotKey Mode from Enabled to Disabled.
4. Open the Exit menu, and select Exit Saving Changes.
Note: When hotkey mode is disabled, press the Fn key and the appropriate
hotkey to access the corresponding hotkey function.

Lenovo ideapad 130 Hardware Maintenance Manual
FRU replacement notices
This section presents notices related to removing and replacing parts. Read
this section carefully before replacing any FRU.

Screw notices
Loose screws can cause a reliability problem. In the Lenovo computer, this
problem is addressed with special nylon-coated screws that have the following
characteristics:
• They maintain tight connections.
• They do not easily come loose, even with shock or vibration.
• They are harder to tighten.
Do the following when you service this machine:
• Keep the screw kit in your tool bag.
• Carefully remove screws for reuse when replacing FRUs.
• Use a torque screwdriver if you have one.
Tighten screws as follows:
• Plastic to plastic
Turn an additional 90° after the screw head touches the surface of the
plastic part:
more than 90°

(Cross-section)

• Logic card to plastic
Turn an additional 180° after the screw head touches the surface of the
logic card:
more than 180°

(Cross-section)

• Torque driver
If you have a torque screwdriver , refer to the “Torque” column for each step.
• Make sure that you use the correct screws. If you have a torque screwdriver,
tighten all screws firmly to the torque shown in the table. Carefully remove
screws for reuse when replacing FRUs. Make sure that all screws are
tightened firmly.
• Ensure torque screwdrivers are calibrated correctly following country
specifications.

Lenovo ideapad 130

Removing and replacing an FRU
This section presents exploded figures with the instructions to indicate how to
remove and replace the FRU. Make sure to observe the following general rules:
1. Do not attempt to service any computer unless you have been trained and
certified. An untrained person runs the risk of damaging parts.
2. Before replacing any FRU, review “FRU replacement notices” on page 30.
3. Begin by removing any FRUs that have to be removed before the failing
FRU. Any of such FRUs are listed at the top of the page. Remove them in
the order in which they are listed.
4. Follow the correct sequence in the steps to remove the FRU, as given in the
figures by the numbers in square callouts.
5. When turning a screw to replace an FRU, turn it in the direction as given by
the arrow in the figure.
6. When removing the FRU, move it in the direction as given by the arrow in
the figure.
7. To put the new FRU in place, reverse the removal procedures and follow
any of the notes that pertain to replacement. For information about
connecting and arranging internal cables, see “Locations” on page 55.
8. When replacing an FRU, use the correct screw as shown in the procedures.

DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any of the
interconnecting cables.
Attention: After replacing an FRU, do not turn on the computer until you have
made sure that all screws, springs, and other small parts are in place and none
are loose inside the computer. Verify this by shaking the computer gently and
listening for rattling sounds. Metallic parts or metal flakes can cause electrical
short circuits.
Attention: The system board is sensitive to, and can be damaged by,
electrostatic discharge. Before touching it, establish personal grounding by
touching a ground point with one hand or using an electrostatic discharge (ESD)
strap (P/N 6405959) to remove potential shock reasons.
Notes:
• This manual applies to the following models:
Lenovo ideapad 130-14IKB/ideapad 130-15IKB/ideapad 130-15AST.
• The illustrations used in this manual are for Lenovo ideapad 130-15AST unless
otherwise stated.

Lenovo ideapad 130 Hardware Maintenance Manual
1010 Optical drive
Figure 1. Removal steps of optical drive
Remove the screw 1, then gently pull the optical drive out in the direction
shown by arrow 2.

Step

Screw (quantity)

Color

Torque

M2.5 × 7 mm, Phillips head, nylok-coated (1)
LOW TO UPPER

Black

1.85±0.15 kgf*cm

Remove the screw 3, then carefully remove the optical drive bracket and bezel
in the directions shown by arrows 4 and 5.
5

4
3

Step

Screw (quantity)

Color

Torque

M2 × 3.5 mm, Phillips head, nylok-coated (1)
ODD BRK TO ODD

Silver

1.85±0.15 kgf*cm

Lenovo ideapad 130

1020 Base cover
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
Figure 2. Removal steps of base cover
Remove the screws 1 from the bottom.
1
1
1

1
1

Step

Screw (quantity)

Color

Torque

M2.5 × 7 mm, Phillips head, nylok-coated (12)
LOW TO UPPER

Black

1.85±0.15 kgf*cm

Remove the base cover 2.

Lenovo ideapad 130 Hardware Maintenance Manual

Note: Applying labels to the base cover
If you see the following labels on base cover, it needs to be peeled off from
the old base cover, and put on the new base cover.
a
b
c
d
e
f
g
h
i
j
k
l

Rating label
GML label
Brazil label
TW vision warning label
Adapter label
KR KRR label
Argentina label
Israel/US/CA/TW label
India BIS label
Indonesia rating label
South Africa label
Malaysia/Indonesia label

For some models, you also need to apply one or two FCC labels. Check the
old base cover; if it has one or two FCC labels, find duplicates of them in the
label kit and apply them to the new base cover.
For the location of each label, refer to the following figures:
Lenovo ideapad 130-15IKB/Lenovo ideapad 130-15AST
c

d
a

b
f

g
h

k
l

Lenovo ideapad 130-14IKB
c

d
a

b
f

g
h

k
l

Lenovo ideapad 130

1030 Battery pack
For access, remove this FRU:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33

DANGER
Only use the battery specified in the parts list for your computer. Any other battery
could ignite or explode.
Figure 3. Removal steps of battery pack
Unplug the battery pack connector in the direction shown by arrow 1, then
remove the screws 2. Remove the battery pack in the direction shown by
arrow 3.

Lenovo ideapad 130-15IKB/Lenovo ideapad 130-15AST

Lenovo ideapad 130-14IKB

1
2

Step

Screw (quantity)

Color

M2 × 6 mm, Phillips head, nylok-coated (3)
Silver
(Lenovo ideapad 130-15IKB/Lenovo ideapad 130-15AST)
BATTERY MODULE TO UPPER
M2 × 6 mm, Phillips head, nylok-coated (2)
Silver
(Lenovo ideapad 130-14IKB)
BATTERY MODULE TO UPPER

Torque
1.85±0.15 kgf*cm

1.85±0.15 kgf*cm

When installing: Make sure that the battery connector is attached firmly.

Lenovo ideapad 130 Hardware Maintenance Manual
1040 Hard disk drive
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35

Attention:
• Do not drop the hard disk drive or apply any physical shock to it. The hard
disk drive is sensitive to physical shock. Improper handling can cause damage
and permanent loss of data.
• Before removing the drive, suggest the customer to backup all the information
on it if possible.
• Never remove the drive while the system is operating or is in suspend mode.
Figure 4. Removal steps of hard disk drive
Detach the connector in the direction shown by arrows 1 and 2. Remove the
screws 3.

1
3

Step

Screw (quantity)

Color

M2 × 6 mm, Phillips head, nylok-coated (4) Silver
HDD BRK TO UPPER & HDD/B TO UPPER

Torque
1.85±0.15 kgf*cm

Lenovo ideapad 130

Figure 4. Removal steps of hard disk drive (continued)
Remove the hard disk drive in the direction shown by arrow 4.
4

Remove the hard disk drive board in the direction shown by arrow 5. Remove
the screws 6, and then take out the metal frame.
6
6
6
6

Step

Screw (quantity)

Color

Torque

M3 × 3 mm, Phillips head, nylok-coated (4)
HDD BRK TO HDD

Silver

3±0.3 kgf*cm

Lenovo ideapad 130 Hardware Maintenance Manual
1050 DIMM
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35
Figure 5. Removal steps of DIMM
Release the two latches on both edges of the socket at the same time in the
directions shown by arrows 1, and then unplug the DIMM in the direction shown
by arrow 2.
1

When installing: Insert the notched end of the DIMM into the socket. Push the
DIMM firmly, and pivot it until it snaps into place. Make sure that it is firmly fixed
in the slot and is difficult to move.
Note: When replacing the memory is completed, you need to restart the
computer after the first reboot.

Lenovo ideapad 130

1060 PCI Express Mini Card for wireless LAN
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35
Important: The preinstalled WLAN module may only be replaced with a
Lenovo approved module in order to comply with FCC and IC regulations.
Refer to “Table 4. Parts list—Overall” on page 60 for Lenovo part numbers for
the approved modules.
Figure 6. Removal steps of PCI Express Mini Card for wireless LAN
Peel off the tape 1

Disconnect the two wireless LAN cables (black, gray) 2. Remove the screw 3.

In step 1, unplug the jacks by using the removal tool antenna RF connector
(P/N: 08K7159), or pick up the connectors with your fingers and gently unplug
them in the direction shown by the arrows.
Notes: The wireless LAN card has 2 cables in step 2.
The wireless LAN card in some models might have 3 cables in step 3.
Step

Screw (quantity)

Color

Torque

M2 × 3.5 mm, Phillips head, nylok-coated (1)
WLAN CARD TO UPPER

Silver

1.85±0.15 kgf*cm

Lenovo ideapad 130 Hardware Maintenance Manual
Figure 6. Removal steps of PCI Express Mini Card for wireless LAN (continued)
Remove the card in the direction shown by arrow 4.

When installing:
• In models with a wireless LAN card that has two antenna connectors, plug
the black cable (1st) (MAIN) into the jack labeled MAIN, and the grey cable
(2nd) (AUX) into the jack labeled AUX on the card.
• In models with a wireless LAN card that has three antenna connectors, plug
the black cable (1st) (MAIN) into the jack labeled 1, the grey cable (3rd) into
the jack labeled 3, and the white cable (2nd) (AUX) into the jack labeled 2 on
the card.

Lenovo ideapad 130

1070 ODD board
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35
Figure 7. Removal steps of ODD board
Detach the ODD board connector in the directions shown by arrows 1 and 2.
Remove the screw 3.
1
2

Remove the ODD board 4.

Step

Screw (quantity)

Color

Torque

M2 X 3.5 mm, Phillips head, nylok-coated (1)
ODD BOARD TO UPPER

Silver

1.85±0.15 kgf*cm

Lenovo ideapad 130 Hardware Maintenance Manual
1080 Fan and heat sink assembly
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35
Figure 8. Removal steps of fan and heat sink assembly
Unplug the fan connector in the direction shown by arrow 1. Remove the
screw 2. Release the antenna from the cable guides.
2

Step

Screw (quantity)

Color

Torque

M2 × 6 mm, Phillips head, nylok-coated (1)
FAN TO UPPER

Silver

1.85±0.15 kgf*cm

Lift the fan in the direction shown by arrow 3.
3

Lenovo ideapad 130

Figure 8. Removal steps of fan and heat sink assembly (continued)
Remove the screws 4.

Lenovo ideapad 130-15IKB/Lenovo ideapad 130-15AST
4
4

Lenovo ideapad 130-14IKB

Step

Screw (quantity)

Color

Silver
M2 × 3.5 mm, Phillips head, nylok-coated (5)
(Lenovo ideapad 130-15IKB/Lenovo ideapad 130-15AST)
THERMAL MODULE TO CPU & THERMAL
MODULE TO GPU (DIS)
M2 × 3.5 mm, Phillips head, nylok-coated (3)
Silver
(Lenovo ideapad 130-14IKB)
THERMAL TO M/B (CPU)

Torque
1.85±0.15 kgf*cm

1.85±0.15 kgf*cm

Lenovo ideapad 130 Hardware Maintenance Manual
Figure 8. Removal steps of fan and heat sink assembly (continued)
Lift the fan in the direction shown by arrow 5.
5

Attention: Do not handle the heat sink assembly roughly. Improper handling
can cause distortion or deformation and imperfect contact with components.

Lenovo ideapad 130-15IKB/Lenovo ideapad 130-15AST

Lenovo ideapad 130-14IKB

When installing:
Before you attach the fan assembly to the computer, apply thermal grease,
at an amount of 0.2 grams, to the a and b parts shown in the figure above.
Either too much or too little grease application can cause a thermal problem
due to imperfect contact with a component.

Lenovo ideapad 130

1090 Speaker
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35
Figure 9. Removal step of speaker
Unplug the speaker connector in the direction shown by arrow 1. Remove the
two speakers 2. Release the antenna from the cable guides.

2
1

When installing: Make sure that the connector is attached firmly.

Lenovo ideapad 130 Hardware Maintenance Manual
1100 RTC battery
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35
Figure 10. Removal steps of RTC battery
Unplug the RTC battery connector in the direction shown by arrow 1. Remove
the RTC battery 2.

When installing: Make sure that the connector is attached firmly.

Lenovo ideapad 130

1110 System board
Important notices for handling the system board:
When handling the system board, bear the following in mind.
• Be careful not to drop the system board on a bench top that has a hard surface,
such as metal, wood, or composite.
• Avoid rough handling of any kind.
• In the whole process, make sure not to drop or stack the system board.
• If you put a system board down, make sure to put it only on a padded surface such
as an ESD mat or conductive corrugated material.
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35
• “1040 Hard disk drive” on page 36
• “1070 ODD board” on page 41
• “1080 Fan and heat sink assembly” on page 42
• “1090 Speaker” on page 45
• “1100 RTC battery” on page 46
Figure 11. Removal steps of system board
Detach the three connectors (EDP cable connector, KB FFC connector,
touchpad connector) in the directions shown by arrows 1, 2 and 3. Remove
the screws 4.
1
2
1

Step

Screw (quantity)

Color

Torque

M2 × 3.5 mm, Phillips head, nylok-coated (3)
MB TO UPPER & DC-IN TO UPPER

Silver

1.85±0.15 kgf*cm

Lenovo ideapad 130 Hardware Maintenance Manual
Figure 11. Removal steps of system board (continued)
Remove the system board in the direction shown by arrow 5.
5

When installing: Make sure that the connectors are attached firmly.

Lenovo ideapad 130

1120 Upper case
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35
• “1040 Hard disk drive” on page 36
• “1070 ODD board” on page 41
• “1080 Fan and heat sink assembly” on page 42
• “1090 Speaker” on page 45
• “1100 RTC battery” on page 46
• “1110 System board” on page 47
Figure 12. Removal steps of upper case
Remove the screws 1.
1

Step

Screw (quantity)

Color

Torque

M2.5 × 4.5 mm, Phillips head, nylok-coated (4)
HINGE BRK TO UPPER

Silver

3±0.3 kgf*cm

Open the hinge in the direction shown by arrows 2. Release the antenna from
the cable guides. Remove the upper case in the direction shown by arrow 3.
2

Lenovo ideapad 130 Hardware Maintenance Manual
1130 LCD unit
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35
• “1040 Hard disk drive” on page 36
• “1070 ODD board” on page 41
• “1080 Fan and heat sink assembly” on page 42
• “1090 Speaker” on page 45
• “1100 RTC battery” on page 46
• “1110 System board” on page 47
• “1120 Upper case” on page 49
Figure 13. Removal steps of LCD unit
Remove the LCD front bezel in the direction shown by arrows 1.
1

Pull the hinge cover in the direction shown by arrows 2. Remove the hinge
cover in the direction shown by arrow 3.

3
2

Lenovo ideapad 130

Figure 13. Removal steps of LCD unit (continued)
Remove the screws 4.
4

Step

Screw (quantity)

Color

Torque

M2 x 2.5 mm, Phillips head, nylok-coated (4)
LCD PANEL TO LCD COVER

Black

1.85±0.15 kgf*cm

Lift the LCD panel slightly 5. Unplug the EDP connector 6. Then remove the
LCD panel.
5

When installing: Make sure that the metal connector is attached firmly.

Lenovo ideapad 130 Hardware Maintenance Manual
1140 EDP cable and integrated camera
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35
• “1040 Hard disk drive” on page 36
• “1070 ODD board” on page 41
• “1080 Fan and heat sink assembly” on page 42
• “1090 Speaker” on page 45
• “1100 RTC battery” on page 46
• “1110 System board” on page 47
• “1120 Upper case” on page 49
• “1130 LCD unit” on page 50
Figure 14. Removal steps of EDP cable and integrated camera
Note: The integrated camera is stuck on the top center of the LCD cover.
Unplug the connector 1, peel of the tape 2.
2

Remove the EDP cable in the direction shown by arrow 3.

Lenovo ideapad 130

Figure 14. Removal steps of EDP cable and integrated camera (continued)
Remove the camera board in the direction shown by arrow 4.
4

When installing: Stick the integrated camera to the top center of the LCD
cover and adjust the placement of it to make sure the connector is attached
firmly.

Lenovo ideapad 130 Hardware Maintenance Manual
1150 LCD hinges
For access, remove these FRUs in order:
• “1010 Optical drive” on page 32
• “1020 Base cover” on page 33
• “1030 Battery pack” on page 35
• “1040 Hard disk drive” on page 36
• “1070 ODD board” on page 41
• “1080 Fan and heat sink assembly” on page 42
• “1090 Speaker” on page 45
• “1100 RTC battery” on page 46
• “1110 System board” on page 47
• “1120 Upper case” on page 49
• “1130 LCD unit” on page 50
• “1140 EDP cable and integrated camera” on page 52
Figure 15. Removal steps of LCD hinges
Remove the screws 1.

1 1
1

Step

1 1

Screw (quantity)

Color

Torque

M2.5 × 2.5 mm, Phillips head, nylok-coated (6)
HINGE BRK TO LCD COVER

Black

3±0.3 kgf*cm

Release the two hinges in the direction shown by arrows 2.

Lenovo ideapad 130

Locations
Front and right-side view
1 Integrated camera
Note:The position of the camera indicator on select models may vary slightly.
Please refer to the actual product.
2 Built-in microphone
3 Wireless LAN antennas
4 Computer display
5 Ventilation slots
6 Touchpad
7 Optical drive (on select models)
8 Kensington mini security slot
9 Power button
2
3

2
3

9
8
6

Lenovo ideapad 130 Hardware Maintenance Manual
Bottom and left-side view
1 Speakers
2 Louvers
3 Power status indicator
Note: For the description of each indicator, see “Status indicators” on page 28.
d Memory card slot
e Novo button
f Combo audio jack
g USB ports
h HDMI port
i RJ-45 port
j Battery status indicator
Note: For the description of each indicator, see “Status indicators” on page 28.
k AC power adapter jack

1
3

Lenovo ideapad 130

Parts list
This section presents the following service parts:
• “Overall” on page 58
• “LCD FRUs” on page 64
• “Miscellaneous parts” on page 66
• “AC adapters” on page 67
• “Screws” on page 68

Note:
Each FRU is available for all types or models, unless specific types or models are
specified.

Attention:
Do not attempt to replace an FRU on your own. If an FRU is damaged, contact
a Lenovo authorized servicer or a marketing representative for replacement
or repair. Only qualified technicians can inspect or repair this product.

Lenovo ideapad 130 Hardware Maintenance Manual
Overall
Lenovo ideapad130-14IKB

10
b

7
9

d
12

Lenovo ideapad 130

Lenovo ideapad 130-15IKB/Lenovo ideapad 130-15AST

10
b

7
9

d
12

Lenovo ideapad 130 Hardware Maintenance Manual
Table 4. Parts list—Overall
No.

FRU

FRU no.

a-d
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

See “Miscellaneous parts” on page 66.
LCD unit (see “LCD FRUs” on page 64.)
Upper Case ASM C 81H6 LA SPA
Upper Case ASM C 81H6 TCH
Upper Case ASM C 81H6 ITA
Upper Case ASM C 81H6 BUL
Upper Case ASM C 81H6 SW
Upper Case ASM C 81H6 SPA
Upper Case ASM C 81H6 SLVN
Upper Case ASM C 81H6 ARA
Upper Case ASM C 81H6 TUR
Upper Case ASM C 81H6 INDIA
Upper Case ASM C 81H6 US
Upper Case ASM C 81H6 HUN
Upper Case ASM C 81H6 ILD (ICE)
Upper Case ASM C 81H6 KOR
Upper Case ASM C 81H6 USI
Upper Case ASM C 81H6 GRE
Upper Case ASM C 81H6 ENG-FRA
Upper Case ASM C 81H6 BEL
Upper Case ASM C 81H6 PORT
Upper Case ASM C 81H6 UK
Upper Case ASM C 81H6 RUS
Upper Case ASM C 81H6 CZ-SK
Upper Case ASM C 81H6 THAI
Upper Case ASM C 81H6 BRA
Upper Case ASM C 81H6 FR-AR
Upper Case ASM C 81H6 GER
Upper Case ASM C 81H6 NORDIC
Upper Case ASM C 81H6 FRA
Upper Case ASM C 81H6 UKR
Upper Case ASM C 81H6 HEB
Upper Case ASM C 81H7 HUN
Upper Case ASM C 81H7 ITA
Upper Case ASM C 81H7 BRA
Upper Case ASM C 81H7 ARA
Upper Case ASM C 81H7 BEL
Upper Case ASM C 81H7 HEB
Upper Case ASM C 81H7 TCH
Upper Case ASM C 81H7 USI
Upper Case ASM C 81H7 RUS
Upper Case ASM C 81H7 GRE
Upper Case ASM C 81H7 US
Upper Case ASM C 81H7 SPA
Upper Case ASM C 81H7 KOR
Upper Case ASM C 81H7 SLVN
Upper Case ASM C 81H7 THAI
Upper Case ASM C 81H7 SW
Upper Case ASM C 81H7 UKR

5CB0R34885
5CB0R34887
5CB0R34883
5CB0R34886
5CB0R34865
5CB0R34863
5CB0R34862
5CB0R34847
5CB0R34846
5CB0R34859
5CB0R34880
5CB0R34892
5CB0R34891
5CB0R34872
5CB0R34871
5CB0R34868
5CB0R34867
5CB0R34875
5CB0R34873
5CB0R34850
5CB0R34848
5CB0R34882
5CB0R34890
5CB0R34858
5CB0R34889
5CB0R34888
5CB0R34845
5CB0R34855
5CB0R34853
5CB0R34851
5CB0R34457
5CB0R34416
5CB0R34430
5CB0R34428
5CB0R34427
5CB0R34424
5CB0R34390
5CB0R34440
5CB0R34438
5CB0R34452
5CB0R34441
5CB0R34451
5CB0R34411
5CB0R34409
5CB0R34449
5CB0R34405
5CB0R34407

CRU ideapad
ideapad
ideapad
ID. 130-14IKB 130-15IKB 130-15AST

N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N

●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●

●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●

●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●

Lenovo ideapad 130

Table 4. Parts list—Overall (continued)
No.

FRU

FRU no.

2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3

Upper Case ASM C 81H7 ILD (ICE)
Upper Case ASM C 81H7 LA SPA
Upper Case ASM C 81H7 PORT
Upper Case ASM C 81H7 CZ-SK
Upper Case ASM C 81H7 FR-AR
Upper Case ASM C 81H7 TUR
Upper Case ASM C 81H7 NORDIC
Upper Case ASM C 81H7 ENG-FRA
Upper Case ASM C 81H7 UK
Upper Case ASM C 81H7 BUL
Upper Case ASM C 81H7 FRA
Upper Case ASM C 81H7 GER
Upper Case ASM C 81H7 INDIA
MB C 81H6 WIN I38130U DISV2G 4G
MB C 81H6 NOK I37020U UMA 4G
MB C 81H6 WIN I37020U DISV2G 4G
MB C 81H6 WIN I78550U DISV2G 4G
MB C 81H6 WIN I78550U UMA 4G
MB C 81H6 NOK I38130U DISV2G 4G
MB C 81H6 NOK I58250U UMA 4G
MB C 81H6 WIN I38130U UMA 4G
MB C 81H6 NOK I38130U UMA 4G
MB C 81H6 NOK I37020U DISV2G 4G
MB C 81H6 NOK I78550U UMA 4G
MB C 81H6 WIN I37020U UMA 4G
MB C 81H6 NOK I78550U DISV2G 4G
MB C 81H6 WIN I58250U DISV2G 4G
MB C 81H6 WIN I58250U UMA 4G
MB C 81H6 NOK I58250U DISV2G 4G
MB C 81H7 NOK I37020U UMA 4G
MB C 81H7 NOKI78550U DIS 4GNODD
MB C 81H7 WIN I78550U DISV2G 4G
MB C 81H7 WIN I38130U DISV2G 4G
MB C 81H7 NOKI38130U UMA 4GNODD
MB C 81H7 WINI78550U DIS 4GNODD
MB C 81H7 WINI58250U DIS 4GNODD
MB C 81H7 WINI38130U DIS 4GNODD
MB C 81H7 WINI37020U DIS 4GNODD
MB C 81H7 NOK I58250U UMA 4G
MB C 81H7 WINI78550U UMA 4GNODD
MB C 81H7 NOKI58250U UMA 4GNODD
MB C 81H7 WIN I78550U UMA 4G
MB C 81H7 NOKI78550U UMA 4GNODD
MB C 81H7 WIN I37020U DISV2G 4G
MB C 81H7 WINI38130U UMA 4GNODD
MB C 81H7 NOK I38130U DISV2G 4G
MB C 81H7 WIN I38130U UMA 4G
MB C 81H7 WIN I58250U DISV2G 4G
MB C 81H7 NOK I78550U DISV2G 4G

5CB0R34398
5CB0R34442
5CB0R34465
5CB0R34462
5CB0R34415
5CB0R34413
5CB0R34455
5CB0R34454
5CB0R34423
5CB0R34421
5CB0R34417
5CB0R34419
5CB0R34460
5B20R34849
5B20R34843
5B20R34842
5B20R34857
5B20R34854
5B20R34884
5B20R34879
5B20R34878
5B20R34869
5B20R34866
5B20R34860
5B20R34838
5B20R34893
5B20R34841
5B20R34840
5B20R34839
5B20R34422
5B20R57965
5B20R34418
5B20R34436
5B20R57966
5B20R57977
5B20R57978
5B20R57979
5B20R57974
5B20R34397
5B20R57972
5B20R57973
5B20R34435
5B20R57967
5B20R34400
5B20R57968
5B20R34406
5B20R34443
5B20R34393
5B20R34401

CRU ideapad
ideapad
ideapad
ID. 130-14IKB 130-15IKB 130-15AST
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●

Lenovo ideapad 130 Hardware Maintenance Manual
Table 4. Parts list—Overall (continued)
No.

FRU

FRU no.

3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
5
6
6
6
6
7
8
8

MB C 81H7 WIN I37020U UMA 4G
MB C 81H7 NOK I38130U UMA 4G
MB C 81H7 WINI37020U UMA 4GNODD
MB C 81H7 NOK I37020U DISV2G 4G
MB C 81H7 NOKI37020U DIS 4GNODD
MB C 81H7 NOKI37020U UMA 4GNODD
MB C 81H7 NOK I58250U DISV2G 4G
MB C 81H7 WIN I58250U UMA 4G
MB C 81H7 NOKI58250U DIS 4GNODD
MB C 81H7 NOK I78550U UMA 4G
MB C 81H7 NOKI38130U DIS 4GNODD
MB C 81H7 WINI58250U UMA 4GNODD
MB C 81H5 WIN A9 UMA
MB C 81H5 NOK A9 DIS NODD
MB C 81H5 WIN E2 UMA NODD
MB C 81H5 WIN A6 UMA
MB C 81H5 NOK A9 DIS
MB C 81H5 NOK A6 UMA
MB C 81H5 NOK A4 UMA
MB C 81H5 WIN A4 UMA
MB C 81H5 NOK E2 UMA
MB C 81H5 WIN A4 DIS NODD
MB C 81H5 WIN E2 UMA
MB C 81H5 WIN A6 UMA NODD
MB C 81H5 NOK A9 UMA
MB C 81H5 WIN A9 DIS
MB C 81H5 NOK E2 UMA NODD
MB C 81H5 WIN A6 DIS
MB C 81H5 NOK A6 DIS
MB C 81H5 WIN A6 DIS NODD
MB C 81H5 NOK A6 UMA NODD
MB C 81H5 WIN A9 UMA NODD
MB C 81H5 NOK A4 DIS
MB C 81H5 WIN A4 DIS
MB C 81H5 WIN A9 DIS NODD
MB C 81H5 NOK A4 DIS NODD
MB C 81H5 NOK A4 UMA NODD
MB C 81H5 WIN A4 UMA NODD
MB C 81H5 NOK A6 DIS NODD
MB C 81H5 NOK A9 UMA NODD
ODD Switch Board C 81H7 W/FFC
CMOS BATTERY C 81H7
Heatsink C 81H7 UMA intel
Heatsink C 81H7 DIS intel
Heatsink C 81H5 DIS AMD
Heatsink C 81H5 UMA AMD
FAN C 81H7
4GB DDR4 2666 SODIMM,Ramaxel
8GB DDR4 2666 SoDIMM,Samsung

5B20R34433
5B20R34467
5B20R57980
5B20R34458
5B20R57976
5B20R57975
5B20R34432
5B20R34453
5B20R57970
5B20R34437
5B20R57971
5B20R57969
5B20R34459
5B20R57983
5B20R57984
5B20R34439
5B20R34448
5B20R34429
5B20R34425
5B20R34426
5B20R34444
5B20R57992
5B20R34472
5B20R57991
5B20R34468
5B20R34431
5B20R57990
5B20R34412
5B20R34469
5B20R57986
5B20R57987
5B20R57985
5B20R34395
5B20R34408
5B20R57981
5B20R57982
5B20R57993
5B20R57994
5B20R57988
5B20R57989
5C50R34463
5B10R34404
5H40R34466
5H40R34461
5H40R34399
5H40R34396
5F10R34470
01AG829
01AG837

CRU ideapad
ideapad
ideapad
ID. 130-14IKB 130-15IKB 130-15AST
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
●
N
●
●
●
N
●
●
N
●
●
N
●
N
●
N
●
●
●
N
●
●
●
N
●
●
●

Lenovo ideapad 130

Table 4. Parts list—Overall (continued)
No.

FRU

FRU no.

8
8
8
8
8
8
8
8
9
9
9
10
10
11
11
11
11
11
12
12
13
13
14
14
14
14
14
14
15
15
15
15
—

2GB DDR4 2400 SoDIMM,Hynix
8GB DDR4 2666 SoDIMM,Ramaxel
4GB DDR4 2666 SOIMM,Hynix
4GB DDR4 2666 SoDIMM,Micron
8GB DDR4 2666 SoDIMM,Micron
8GB DDR4 2666 SOIMM,Hynix
2GB DDR4 2400 SoDIMM
4GB DDR4 2666 SoDIMM,Samsung
Wireless,CMB,LTN,NFA435A
Wireless,CMB,CBT,8821CE
Wireless,CMB,IN,3165 ac
HLDS GUE0N DVD RW
DA-8AESH
Dummy ODD C 81H7
Storage,HDD,500G,5400,7mm,ST
WD WD5000LPCX-24VHAT0
Storage,HDD,1T,5400,7mm,SATA,WD
RW1D ST1000LM035 1T HDD
Toshiba MQ01ABF050 500G HDD
Storage SSD CV8 128G 2.5'' Liteon
Storage SSD CV8 256G 2.5'' Liteon
Storage SSD SC313 256G Hynix
Storage SSD 545s 256GB 2.5'' Intel
Storage SSD SC313 128G Hynix
Storage SSD PM871b 128G SAM
2nd HDD BAY C 81H7
HDD Board C 81H6 W/FFC
HDD Board C 81H7 W/FFC
HDD board C 81H7 for 2nd HDD
Speaker C 81H6 L+R
Speaker C 81H7 L+R
SP/B L17M2PB7 7.56V30Wh2cell
SP/A L16M2PB1 7.5V30Wh2cell
CP/C L16C2PB2 7.6V30Wh2cell
SP/A L16M2PB2 7.5V35Wh2cell
LG L17L2PF1 7.56V30Wh2cell bty
CP/C L16C2PB1 7.6V35Wh2cell
Lower case C 81H6 W/O 2nd HDD
Lower case C 81H6 W/2nd HDD
Lower case C 81H7 W/O 2nd HDD
Lower case C 81H7 W/2nd HDD
AC adapter (see “AC adapters” on page 67).

01FR309
01AG843
01AG823
01AG831
01AG841
01AG824
01AG700
01AG836
01AX709
01AX710
00JT497
5DX0J46488
5DX0L08424
5M20R34403
01FR401
5H20J35762
01FR402
5H20L22184
5H20L34560
01FR549
01FR550
01FR515
01FR531
01FR514
01FR502
5M20R34414
5C50R34852
5C50R34420
5C50R34410
5SB0R34881
5SB0R34474
5B10Q71253
5B10M86148
5B10M88058
5B10M86149
5B10Q41213
5B10M88059
5CB0R34861
5CB0R34844
5CB0R34392
5CB0R34456

CRU ideapad
ideapad
ideapad
ID. 130-14IKB 130-15IKB 130-15AST
N
●
●
N
●
●
●
N
●
●
●
N
●
●
N
●
●
N
●
●
●
N
●
●
N
●
●
●
N
●
●
●
N
●
●
●
N
●
●
N
●
●
●
N
●
●
●
*
●
●
●
N
●
●
●
N
●
●
●
N
●
●
●
N
●
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
●
N
●
●
●
N
●
●
●
N
●
N
●
●
N
●
●
●
N
●
N
●
●
N
●
●
●
N
●
●
●
N
●
●
●
N
●
●
N
●
●
●
N
●
●
N
●
N
●
N
●
●
N
●
●

Lenovo ideapad 130 Hardware Maintenance Manual
LCD FRUs
In Lenovo ideapad 130-14IKB/Lenovo ideapad 130-15IKB/
Lenovo ideapad 130-15AST, there are following types of LCDs.
• “14.0-in. HD/FHD LED”
1

Lenovo ideapad 130

• “15.6-in. HD/FHD LED”
1

Lenovo ideapad 130 Hardware Maintenance Manual
Table 5. Parts list—LCD FRUs
No.

FRU

FRU no.

1
1
2
2
3
3
3
3
3
3
3
3
3
3
3
3
4
4
5
5
6
6
7
7

LCD Bezel C 81H6
LCD Bezel C 81H7
Hinge Cover C 81H6
Hinge Cover C 81H7
BO NT140FHM-N41V8.0 FHDT AG S NB
IN N140BGA-EA3 HDT AG S NB
AU B140XTN02.E HWCA HDT AG S NB
IV M140NWR6 R1 HW1.2 HDT AG S NB
AU B140HTN01.E 2A FHDT AG S NB
IN N140HGE-EAA C4 FHDT AG S NB
AU B156HTN03.8 0C FHDT AG S NB
AU B156XTN07.1 3A HDT AG S NB
IN N156BGA-EA2 HDT AG S NB
IN N156HGA-EAB FHDT AG S NB
BO NT156FHM-N41 FHDT AG S NB
BO NT156WHM-N42 V8 HDT AG S NB
EDP cable C 81H6
EDP cable C 81H7
Camera C 81H7 0.3M
Camera C 81H7 1M
Hinge C 81H6 L+R
Hinge C 81H7 L+R
LCD Cover C 81H6 W/Antenna
LCD Cover C 81H7 W/Antenna

5B30R34874
5B30R34450
5CB0R34856
5CB0R34446
5D10L01874
5D10K85755
5D10P54235
5D10Q95195
5D10L08701
5D10K93439
5D10L08702
5D10H52713
5D10K81086
5D10K93435
5D10K93434
5D10K81097
5C10R34877
5C10R34473
5C20R34402
5C20R34394
5H50R34870
5H50R34445
5CB0R34876
5CB0R34391

ideapad
ideapad
CRU ideapad
ID. 130-14IKB 130-15IKB 130-15AST
N
●
N
●
●
N
●
N
●
●
N
●
N
●
N
●
N
●
N
●
N
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
●
N
●
N
●
●
N
●
●
●
N
●
●
●
N
●
N
●
●
N
●
N
●
●

Miscellaneous parts
Table 6. Parts list—Miscellaneous parts
FRU

P/N

ideapad
ideapad
CRU ideapad
ID. 130-14IKB 130-15IKB 130-15AST

System miscellaneous parts:
• (a) ODD BRACKET C 81H7
5B40R34389
*
●
●
• (b) ODD BEZEL C 81H7
5B30R34471
*
●
●
• (c) HDD Bracket C 81H7
5B40R34447 N
●
●
• (d) Wlan Sponge C 81H7
5T10R34434
N
●
●
Note: Italicized letters in parentheses are references to the exploded view in “Overall” on page 58.

●
●
●
●

Lenovo ideapad 130

AC adapters
Table 7. Parts list—AC adapters
FRU

P/N

PA-1450-55LR 20V2.25A COO
ADL45WCK 20V2.25A COO
ADLX65CCGU2A 20V3.25A COO
PA-1450-55LS 20V2.25A COO
ADP-45DW J 20V2.25A COO
PA-1450-55LK 20V2.25A COO
ADL45WCE 20V2.25A COO
ADLX65CDGU2A 20V3.25A COO
ADLX65CCGC2A 20V3.25A COO
PA-1450-55LI 20V2.25A COO
ADLX65CLGU2A 20V3.25A COO
ADLX65CLGR2A 20V3.25A COO
ADP-45DW E 20V2.25A COO
ADP-45DW G 20V2.25A COO
ADL45WCC 20V2.25A COO
ADLX65CCGR2A 20V3.25A COO
ADLX65CCGK2A 20V3.25A COO
ADLX65CDGR2A 20V3.25A COO
ADP-45DW B 20V2.25A COO
PA-1450-55LL 20V2.25A COO
ADLX65CDGK2A 20V3.25A COO
ADP-45DW H 20V2.25A COO
ADL45WCA 20V2.25A COO
ADLX65CCGB2A 20V3.25A COO
ADLX65CCGI2A 20V3.25A COO
ADLX65CLGI2A 20V3.25A COO
ADLX65CLGB2A 20V3.25A COO
ADLX65CDGG2A 20V3.25A COO
PA-1450-55LN 20V2.25A COO
ADLX65CCGG2A 20V3.25A COO
ADLX65CLGG2A 20V3.25A COO
ADLX65CLGK2A 20V3.25A COO
ADLX65CLGC2A 20V3.25A COO
ADLX65CDGB2A 20V3.25A COO
ADLX65CDGC2A 20V3.25A COO
PA-1450-55LZ 20V2.25A COO
ADP-45DW A 20V2.25A COO
ADL45WCH 20V2.25A COO
ADLX65CDGI2A 20V3.25A COO
ADL45WCD 20V2.25A COO
ADLX65CCGA2A 20V3.25A COO
ADL45WCG 20V2.25A COO
ADLX65CLGE2A 20V3.25A COO
ADLX65CDGA2A 20V3.25A COO
ADP-45DW C 20V2.25A COO
ADP-45DW D 20V2.25A COO
ADLX65CDGE2A 20V3.25A COO

01FR122
01FR130
01FR154
01FR123
01FR110
01FR036
01FR131
01FR137
01FR152
01FR121
01FR146
01FR148
01FR115
01FR114
01FR128
01FR157
01FR155
01FR140
01FR111
01FR120
01FR138
01FR113
01FR126
01FR160
01FR156
01FR147
01FR151
01FR136
01FR118
01FR153
01FR145
01FR037
01FR144
01FR143
01FR135
01FR125
01FR109
01FR134
01FR139
01FR129
01FR158
01FR133
01FR150
01FR141
01FR116
01FR112
01FR142

ideapad
ideapad
CRU ideapad
ID. 130-14IKB 130-15IKB 130-15AST
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●

Lenovo ideapad 130 Hardware Maintenance Manual
Table 7. Parts list—AC adapters (continued)
FRU

P/N

ADLX65CCGE2A 20V3.25A COO
ADLX65CLGA2A 20V3.25A COO
ADL45WCF 20V2.25A COO
PA-1450-55LU 20V2.25A COO
ADP-45DW K 20V2.25A COO
PA-1450-55LG 20V2.25A COO
ADL45WCB 20V2.25A COO

01FR159
01FR149
01FR132
01FR124
01FR117
01FR119
01FR127

ideapad
ideapad
CRU ideapad
ID. 130-14IKB 130-15IKB 130-15AST
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●
*
●
●
●

Screws
Table 8. Parts list—Screws
FRU
Screw pack C 81H6
Screw pack C 81H7

ideapad
ideapad
CRU ideapad
ID. 130-14IKB 130-15IKB 130-15AST
5S10R34864 N
●
5S10R34464 N
●
●
P/N

Notices

Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe
any Lenovo intellectual property right may be used instead. However, it is the
user’s responsibility to evaluate and verify the operation of any other product,
program, or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents.
L E N O V O G R O U P LT D . P R O V I D E S T H I S P U B L I C AT I O N “ A S I S ”
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some jurisdictions do not allow disclaimer of express or implied
warranties in certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes
will be incorporated in new editions of the publication. Lenovo may make
improvements and/or changes in the product(s) and/or the program(s)
described in this publication at any time without notice.
The products described in this document are not intended for use in
implantation or other life support applications where malfunction may result in
injury or death to persons. The information contained in this document does not
affect or change Lenovo product specifications or warranties. Nothing in this
document shall operate as an express or implied license or indemnity under the
intellectual property rights of Lenovo or third parties. All information contained
in this document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for
this Lenovo product, and use of those Web sites is at your own risk.
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments
may vary significantly. Some measurements may have been made on
development-level systems and there is no guarantee that these measurements
will be the same on generally available systems. Furthermore, some
measurements may have been estimated through extrapolation. Actual results
may vary. Users of this document should verify the applicable data for their
specific environment.

Lenovo ideapad 130 Hardware Maintenance Manual
Trademarks
The following terms are trademarks or registered trademarks of Lenovo in the
United States, other countries, or both.
Lenovo
ideapad
Microsoft and Windows are trademarks of Microsoft Corporation in the United
States, other countries, or both.
Other company, products, or service names may be trademarks or service
marks of others.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Lenovo
Create Date                     : 2018:05:22 11:33:42+08:00
Modify Date                     : 2018:05:22 11:34:35+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08
Instance ID                     : uuid:a26b24f0-8747-43c0-9c4f-7d579038969f
Original Document ID            : adobe:docid:indd:85d77ef0-0fc2-11df-aaad-87e79053a371
Document ID                     : xmp.id:1C62E7A4705DE81196F2E009BBFC9E4E
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:1B62E7A4705DE81196F2E009BBFC9E4E
Derived From Document ID        : adobe:docid:indd:85d77ef0-0fc2-11df-aaad-87e79053a371
Derived From Original Document ID: adobe:docid:indd:85d77ef0-0fc2-11df-aaad-87e79053a371
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2018:05:22 11:33:42+08:00
Metadata Date                   : 2018:05:22 11:34:35+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Title                           : ideapad 130 HMM
Creator                         : Lenovo
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Layout                     : SinglePage
Page Count                      : 74

EXIF Metadata provided by EXIF.tools

Lenovo Ideapad 130 HMM Hardware Maintenance Manual 14IKB, 15IKB 14IKB Laptop (ideapad) Type 81H6 15ast 201805

Navigation menu

Versions of this User Manual:

Views

Navigation