Lester Electrical of Nebraska 22220 Universal Transceiver Module User Manual OBH22220 User s Manual

Download:
Mirror Download [FCC.gov]
Document ID	137848
Application ID	cPkWHmqBVL49Er7+aUyiwQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.57kB (19624 bits)
Date Submitted	2001-02-23 00:00:00
Date Available	2001-02-23 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	Acrobat PDFWriter 3.02 for Windows
Document Lastmod	2001-02-14 14:49:11
Document Title	OBH22220 - User's Manual
Document Creator	Microsoft Word
Document Author:	HS Berger

Exhibit 8
UNIVERSAL TRANSCEIVER
MODEL 22220
FCC ID #OBH22220
PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS
For correct operation of the equipment, it is important to read and be familiar
with this entire manual before installing and operating the charger.
DO NOT DISCARD THIS MANUAL AFTER READING.
LOOK FOR THIS SYMBOL TO POINT OUT SAFETY PRECAUTIONS. IT MEANS:
BECOME ALERT—YOUR SAFETY IS INVOLVED. IF YOU DO NOT FOLLOW THESE
SAFETY INSTRUCTIONS, INJURY OR PROPERTY DAMAGE CAN OCCUR.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
operation of other moving objects, vehicles
or other machinery.
Never mount the
Universal Transceiver near radiators,
heating sources or high temperature areas.
Never cover or obstruct fire sprinkler
systems, access panels, limit switches,
circuit breakers, light fixtures or other
installed
machinery,
electronic
or
mechanical devices.
INSTALLATION INSTRUCTIONS
Tools needed to install Universal Transceiver Model
22220 and Base Station PC: drill, ¼" drill bit, Phillips
screwdriver, ¼x 5" acid resistant cable ties
The Universal Transceiver unit has been designed
for optimum operation with a clear, unobstructed
"Line of Sight" signal transmission range of two
hundred feet (200') or less. When mounting the
Universal Transceiver, machinery, walls, doors and
other physical structures should be avoided in order
to achieve maximum antenna performance.
CAUTION: USE CAUTION WHEN WORKING
AROUND BATTERY CHARGING AREAS AND
INDUSTRIAL ENVIRONMENTS. ALWAYS WEAR
APPROVED PROTECTIVE EYEWEAR. ALWAYS
WORK IN A WELL-LIGHTED AREA.
WEAR
APPROVED SAFETY SHOES. FOLLOW ALL
POSTED SAFETY WARNINGS WHEN WORKING
ON AND AROUND LADDERS. USE EXTREME
CAUTION WHEN OPERATING TOOLS. DO NOT
REST TOOLS ON TOP OF MACHINERY OR
STORAGE RACK BEAMS.
Note:
ASSEMBLY PROCEDURE –
Universal Transceiver
1. Locate a clear wall, ceiling or non-metal rack
area to mount the Universal Transceiver. The
unit should be mounted at least one foot (1')
from metal pipes or racks. Avoid mounting
Universal Transceiver near any sources of
potential noise interference such as electric
motors, fluorescent lamps, radio transmitters,
infrared devices, etc. (at least ten feet (10') of
clear area is recommended). Line of site
Do not mount the Universal Transceiver
where water spills may occur. Do not mount
Universal Transceiver on unstable surfaces
such as rolling doors, access panels, etc.
Do not mount Universal Transceiver where it
may be struck by or interfere with the
Operating Instructions
31082A
Exhibit 8
obstructions may interfere with maximum signal
strength and reception.
3. Secure the RS232 Cable to wall and rack areas
using approved cable ties and wall style cable
fasteners. Do not allow anything to rest on the
Base Station PC or its cables including other
signal transmission cables or lines.
2. Using the Universal Transceiver mounting
bracket as a guide, mark two spots to be drilled
to support the unit. Use extreme caution to
avoid drilling into walls containing wiring or
pipes.
4. Attach an approved telecommunications cable to
the receptacle port on the rear of the Base
Station PC. Neatly secure the cable along its
path using approved cable ties.
ASSEMBLY PROCEDURE –
Base Station PC
5. Attach the 110 VAC power cable to the rear of
the Base Station PC. Plug the power cable in to
the nearest 110 VAC power source.
1. Determine a suitable wall or rack location to
mount the Base Station PC within twenty-five
feet (25') of the Universal Transceiver unit near
a standard 110 VAC power supply and approved
telephone jack. Use only the supplied hardware
brackets when mounting the Base Station PC.
Do not drill or tap any holes in the case of the
Base Station PC.
6. Turn Base Station PC power on using the rocker
switch located on the rear of the unit.
There are no user serviceable parts in the Universal
Transceiver or Base Station PC. Any attempt to
access or repair any internal components will void
the manufacturer's warranty.
2. Attach the RS232 nine-pin cable to the Universal
Transceiver. Carefully route this cable to the
Base Station PC and attach cable to RS232
receptacle.
For product warranty or customer assistance, please
contact Lester Electrical, Inc. at (402) 477-8988.
Manufactured by Lester Electrical, Inc.
Lincoln, Nebraska
Operating Instructions
31082A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Creator                         : Microsoft Word
Create Date                     : Thursday, January 11, 2001 2:13:54 PM
Title                           : OBH22220 - User's Manual
Author                          : HS Berger
Producer                        : Acrobat PDFWriter 3.02 for Windows
Subject                         : 
Modify Date                     : 2001:02:14 14:49:11-07:00
Page Count                      : 2
Has XFA                         : No

EXIF Metadata provided by EXIF.tools