Levelone Fcs 1030 Users Manual User's

FCS-1030 to the manual ead9f89c-1f7f-4809-bc55-10630c3b945b

2015-02-09

: Levelone Levelone-Fcs-1030-Users-Manual-571229 levelone-fcs-1030-users-manual-571229 levelone pdf

Open the PDF directly: View PDF .
Page Count: 73

Download
Open PDF In Browser	View PDF

LevelOne
FCS-1030
10/100Mbps IP Network Camera

User’s Manual

Table of Contents
Before You Use This Product......................................................................4
Warning Before Install..............................................................................5
Package Contents ....................................................................................7
Installation .............................................................................................5
Hardware installation..........................................................................5
Software installation...........................................................................1
Using Installation Wizard.....................................................................6
User Interface ..............................................................................6
Action buttons..............................................................................7
Function buttons ..........................................................................8
Setup .........................................................................................8
System Setting ............................................................................9
Change root password...................................................................9
Adjust date and time................................................................... 10
Network Setting ......................................................................... 11
Fix the IP address....................................................................... 11
Basic Network Settings................................................................ 12
Upgrade .................................................................................... 12
Device Information ..................................................................... 12
Package Information ................................................................... 13
File Selection ............................................................................. 14
Upgrade .................................................................................... 14
How to Use ..................................................................................... 15
Authentication............................................................................ 15
Installing plug-in.............................................................................. 16
Primary user’s capability ................................................................... 17
Main Screen with Camera View ..................................................... 17
Digital Zoom .............................................................................. 18
Snapshot................................................................................... 18
Client settings ............................................................................ 19
Administrator’s capability .................................................................. 22
Fine-tuning for Best Performance .................................................. 22
Opening accounts for new users ................................................... 24
-1-

Change homepage layout ............................................................ 25
Build a multimedia web attraction site ........................................... 30
Build a security application .......................................................... 33
Software revision upgrade ........................................................... 34
Definitions in Configuration ..................................................................... 35
System parameters .......................................................................... 36
Security settings .............................................................................. 37
Network settings.............................................................................. 38
General ..................................................................................... 38
SMTP ........................................................................................ 38
FTP .......................................................................................... 39
HTTP ........................................................................................ 39
Streaming ................................................................................. 40
DDNS and UPnP settings ................................................................... 41
Video codec parameters .................................................................... 41
Motion detection .............................................................................. 44
Application settings .......................................................................... 45
Weekly schedule......................................................................... 45
Send out the snapshot while motion detection ................................ 45
Sequential operation ................................................................... 45
Homepage layout settings............................................................ 47
Viewing system log .......................................................................... 48
Viewing system parameters............................................................... 48
Factory default ................................................................................ 48
Appendix.............................................................................................. 49
A. Troubleshooting ........................................................................... 49
Status LED ................................................................................ 49
Reset and restore ....................................................................... 49
B. Frequently asked questions ........................................................... 43
C. URL commands of the Network Camera........................................... 46
Capture update Snapshot of JPEG image........................................ 46
Query status of the digital input ................................................... 46
Drive the digital output ............................................................... 46
Restore factory default settings .................................................... 47
Restart system........................................................................... 47
-2-

Page URL .................................................................................. 48
System resource URL .................................................................. 48
General format of command URL .................................................. 49
System configuration URL ............................................................ 49
Security configuration URL ........................................................... 50
Network configuration URL........................................................... 50
DDNS & UPnP configuration URL ................................................... 52
Video configuration URL .............................................................. 53
Image quality configuration URL ................................................... 54
Application configuration URL ....................................................... 55
Homepage layout configuration URL .............................................. 55
D. Technical specifications ................................................................. 57

-3-

Before You Use This Product
The use of surveillance devices may be prohibited by law in your country. The
FCS-1030 Network Camera is not only a high-performance web-ready camera but
also can be part of a flexible surveillance system. It is the user’s responsibility to
ensure that the operation of such devices is legal before installing this unit for its
intended use.
It is important to first verify that all contents received are complete according to the
list in the "Package Contents" chapter. Take notice of the warnings in “Quick
installation guide” before the Network Camera is installed, then carefully read and
follow the instructions in the “Installation” chapter to avoid damages due to faulty
assembly and installation.

This also ensures the product is used properly as

intended.
The Network Camera is a network device and its use should be straightforward for
those who have basic network knowledge. The “Troubleshooting” chapter in the
Appendix provides remedies to the most common errors in set up and configuration.
You should consult this chapter first if you run into a system error.
The Network Camera is designed for various applications including video sharing,
general security/surveillance, etc.

The “How to Use” chapter suggests ways to best

utilize the Network Camera and ensure proper operations. For the creative and
professional developers, the "URL Commands of The Network Camera " chapter
serves to be a helpful reference to customize existing homepages or integrating with
the current web server.

For paragraphs preceded by
completely the warnings.

the reader should use caution to understand

Ignoring the warnings may result in serious hazards or

injuries.

-4-

Warning Before Install

-5-

-6-

Package Contents

-7-

Installation
In this manual, "User" refers to whoever has access to the FCS-1030 Network Camera,
and "Administrator" refers to the person who can configure the Network Camera and
grant user access to the camera.

Hardware installation
Please verify that your product package contains all the
accessories listed in the foregoing Package Contents.
Depending on the user’s application, an Ethernet cable
may be needed. The Ethernet cable should meet the specs
of UTP Category 5 and not exceed 100 meters in length.
Connect the power adapter jack to the Network
Camera before plugging in to the power socket. This will
reduce the risk of accidental electric shock.

Upon powering up, the device runs through a self-test procedure and the front LEDs will
blink between green and red a few times.

If self-test passes, the LED will be green and

the Network Camera will standby for getting IP address. After getting IP Address, the LED
will blink green every second. If self-test fails the red LED will blink several times. Refer
to Appendix A for troubleshooting.

-5-

Software installation
The following are steps for the software installation.
STEP 1 Put the Installation disk into the CD-ROM drive, and the installation should
start automatically. If the installation does not start, click on “Start” on the lower left
corner of your screen, open “My Computer” and double click on the CD-ROM icon. The
Installation Wizard Installation Window will appear.

STEP 2 There are links on this page, including Install Software, User’s Manual and
Customer Homepage. Click on “Install Software” to enter Install Software page.

STEP 3 There are links on this page, including Installation Wizard, User’s Manual and
Surveillance Software. Click on “Installation Wizard” to launch the setup program.

-2-

STEP 4 Select the installation directory for this application software and click on “Next”.
You can also change the installation directory from the default directory by clicking on
“Browse…”

STEP 5 Select a program folder to install the application software into and then click on
“Next”.

-3-

STEP 6 Click on “Finish” to finish installation. This completes the installation.

-4-

Using Installation Wizard
User Interface
Once you run the Installation Wizard, you will see the user interface. You can click on
the device list to select a device. The three buttons (Setup, Upgrade, and Reset to
default) won’t be enabled until you select at least one device.

Installation wizard allows you to setup or upgrade multiple devices (of the same model) at the
same time. If you selected different models, then the buttons will be disabled. There are five
buttons on the bottom of the main page, and five buttons on the left panel of the main page.

-6-

Action buttons
Click on this button to clean up the device list and search all devices on the within
the same subnet again. It will take about 5 seconds.
To setup or upgrade the devices which can not be found by Installation Wizard,
please click on this button to add them manually. Click on this button will popup a
dialog. You can input the IP address and click on Ok to add the device into the device list.

Click on this button will remove all the selected devices from the device list. The
devices that you remove might be show up again if you click the search button or
add them into list manually.
While you selected several devices, this button allows you to uncheck all the
selected devices by one click instead of uncheck the selected devices one by one.

Click on this button will open the web browsers to link to all the selected
devices. (One browser per device)

-7-

Function buttons

Click on this button to modify the settings of the selected devices. For more detail,
please refer to 0 Setup.

Click on this button to upgrade the firmware of the selected devices. For more
detail, please refer to 0 Upgrade.
Click on this button to back to the previous page or main page

Click on this button to reset the selected devices to default settings.

Click on this button to back to the previous page or main page
Click on this button to close the Installation Wizard.

Click on this button to get information about the Installation Wizard.

Setup
When you select one or multiple devices (of the same model) , the “Setup” button will be enabled.
Click on it to modify the settings of the selected device(s). After clicking on the “Setup” button,
Installation Wizard will try to connect to the selected device(s). If the authentication is failed, it will
popup a dialog) to ask for correct password and http port number.

-8-

Note: The default password is the MAC address with capital letter.

System Setting
After connected to the selected device(s), it will switch to system setting page.
Click on this button to back to the previous page or main page

Click on this button to keep the settings and go to the next page.
Click on this button to discard the settings of the current page and go to the next
page.

Change root password
To change the administrator’s password, type the new password in both root password and
confirm password text boxes identically. What is typed will be displayed as asterisks for security
purposes. The maximum password is 14 characters.

-9-

Adjust date and time
There are three ways to adjust system date and time. The easiest way is to make Network
Camera "Sync with computer time". The second way “Manual” is to set the date and time
manually by entering new values. Notice the format in the related field while typing. The third way
“Automatic” is to make Network Camera automatically synchronize with timeservers over the
Internet every hour.
- 10 -

Network Setting
In this page, you can change the server’s IP address, subnet mask, default router, primary dns,
and secondary dns.

Fix the IP address
Check "Reset IP address at next boot" will force Network Camera to reconfigure its IP address
whenever it reboot. If you want the Network Camera to use a fixed IP, please uncheck the "Reset
IP address at next boot" and assign a valid IP address. If you select more than one device,
changing the IP address is not allowed and the IP address field will be disabled.
- 11 -

Basic Network Settings
You can setup the network setting by this page. Usually this is no need to be changed, if you do
change it please make sure you input the correct setting or the device may not be reachable.

Upgrade
When you select one device or multiple devices (of the same model), the “Upgrade” button will
be enabled. Click on it to upgrade the firmware of the selected device(s). After click on the
“Upgrade” button, Installation Wizard will try to connect the selected device(s). If the
authentication is failed, it will popup a dialog to ask for the correct password and http port number.

Note: The default password is the MAC address with capital letter.

Device Information
After connected to the selected device, it will display.

- 12 -

Package Information
The package information will show the information about the file that you selected.
Firmware version: The version number of the selected firmware.
Supported script version: The maximum script version that firmware can support.
Web page version: The version number of the web page.
Script version: Script version used by web page and server script.
Viewer plugin version: The version number of the viewer plugin.
- 13 -

Upgrade plugin version: The version number of the upgrade plugin
Supported language: The language that the selected file supports.

File Selection
You can use the file combolist to browse the file that you want upgrade onto the selected device(s).
After selecting the file, Installation Wizard will check whether the file you selected is correct. If it is
correct, then the package information will display the information about the file and enable the
“Upgrade” button. Therefore you can click on the button to upgrade the firmware. If it is not
correct, then it will popup a warning message.

Upgrade
Click on the “Upgrade” button to upgrade the firmware of the selected device(s). It will popup the
dialog to show the progress of the upgrading process.

After the upgrade process is done. Click

“Done” to finish.

- 14 -

How to Use
Authentication
After opening the Web browser and typing in the URL of the Network Camera, a
dialogue window pops up to request a username and password. Upon successful
authentication, the following figure is displayed.
The foreground is the login window and the background shows the message if
authentication fails. The user may check the option box to save the password for future
convenience.

This option is not available to the Administrator for obvious reason.

After successful linkage, the authentication window should pop up.
The default user name is root.
The default password is the MAC address with capital letter .

- 15 -

Installing plug-in
For the initial access to the Network Camera in Windows, the web browser may prompt
for permission to install a new plug-in for the Network Camera. Permission request
depends on the Internet security settings of the user’s PC or notebook. If the highest
security level is set, the computer may prohibit any installation and execution attempt.
This plug-in has been registered for certificate and is used to display the video in the
browser. Users may click on

to proceed. If the web browser does not allow the

user to continue to install, check the Internet security option and lower the security
levels or contact your IT or networking supervisor for help.

- 16 -

Primary user’s capability
Main Screen with Camera View
The main page layout has two parts:
Configuration functions: The camera can be configured using these user interfaces.
Camera View: What the camera sees.
Click on the configuration link to the left of the image window to enter the configuration
page.

- 17 -

Digital Zoom
Click on the magnifier icon under the camera view then the digital zoom control panel
will be shown. Uncheck “Disable digital zoom” and use the slider control to change the
zoom factors.

Snapshot
Click on “Snapshot”, web browser will pop up a new window to show the snapshot.
Users can point at the snapshot and click the right button of mouse to save it.

- 18 -

Client settings
At the initial access to the “Connection type” page in Windows, the web browser will ask
for a new plug-in installation, the plug-in being the Network Camera. This plug-in has
been registered for certification and can be used to change the parameters at the
client’s site. The user may click on

to install the plug-in. If the web browser

does not allow the user to complete the installation, check the Internet security to
lower the security level or contact your IT or networking supervisor.

- 19 -

There are two settings for the client side. One is “Media Option” for users to
determine if audio should be muted. The other is “Protocol Option” which allows
choices on connection protocol between client and server. There are three protocols
choices to optimize your usage - UDP, TCP and HTTP.
The UDP protocol allows for more real-time audio and video streams. However, some
packets may be lost due to network burst traffic and images may be obscured.
The TCP protocol allows for less packet loss and produces a more accurate video
display. The downside with this protocol is that the real-time effect is worse than that
with the UDP protocol.
The HTTP protocol must be selected if the network is protected by a firewall and it only
allows HTTP Port (80) to be opened. In this mode, audio will not be sent and only video
is operational.

If no special need is required, UDP protocol is recommended. Generally

speaking, the client’s choice will be in the order of UDP → TCP → HTTP.

After the

Network Camera is connected successfully, “Protocol Option” will indicate the selected
protocol. The selected protocol will be recorded in the user's PC and will be used for the
next connection. If the network environment is changed, or the user wants to let the
web browser to detect again, manually select the UDP protocol, save, and return HOME
to re-connect.
- 20 -

http:///protocol.html
is the domain name or the original IP address of the Network
Camera.

- 21 -

Administrator’s capability
Fine-tuning for Best Performance
Best performance generally equates to the fastest image refresh rate with the best
video quality, and at the lowest network bandwidth as possible. The three factors,
“Maximum frame rate”, “Fix bit rate”, and “Fix quality” on the Video Configuration page,
are correlative to allow for achieving the best performance possible.

For Best Real-time Video Images
To achieve good real-time visual effect, the network bandwidth should be large enough
to allow a transmission rate of greater than 20 image frames per second. If the
broadband network is over 1 Mbps, set the “Fix bit rate” to 1000Kbps or 1200Kbps, and
set “Fix quality” at the highest quality. The maximum frame rate is 30. If your network
bandwidth is more than 384Kbps, you can fix the bit rate according to your bandwidth
and set the maximum frame rate to 30 fps. If the images vary dramatically in your
- 22 -

environment, you may want to slow the maximum frame rate down to 20 fps in order
to lower the rate of data transmission. This allows for better video quality and the
human eyes cannot readily detect the differences between those of 20, 25, or 30
frames per second. If your network bandwidth is below 384 Kbps, set the “Fix bit rate”
according to your bandwidth and try to get the best performance by fine-tuning with
the “Maximum frame rate”. In a slow network, greater frame rate results in blur images.
Another work-around is to choose “Half” in the “Size” option for better images, or
“Halfx2” for a larger image view. Video quality performance will vary somewhat due to
the number of users viewing on the network; even when the parameters have initially
been finely tuned.

Performance will also suffer due to poor connectivity because of

the network’s burst constraint.

Only Quality Images Will Do
To have the best video quality, you should set “Fix quality” at “Detailed” or “Excellent”
and adjust the “Maximum frame rate” to match your network’s bandwidth. If your
network is slow and you receive “broken” pictures, go to the TCP protocol in
“Connection type” and choose a more appropriate mode of transmission. The images
may suffer a time delay due to a slower connection.

The delay will also increase with

added number of users.

Somewhere Between Real-time and Clear Images
If you have a broadband network, set “Fix quality” at ”Normal” or better, rather than
setting “Fix bit rate”. You can also fix the bandwidth according to your actual network
speed and adjust the frame rate.
15 fps.

Start from 30 fps down for best results but not below

If the image qualities are not improved, select a lower bandwidth setting.

- 23 -

Opening accounts for new users

Protect Network Camera by passwords
The Network Camera is shipped without any password by default. That means
everyone can access the Network Camera including the configuration as long as the IP
address is known. It is necessary to assign a password if the Network Camera is
1 to enable protection.
intended to be accessed by others. Type a new word twice in ○

This password is used to identify the administrator. Then add an account with user
2 . Network Camera can provide twenty
name and password for your friends in ○

accounts for your valuable customers or friends. Each account identifies the access
right rather than the real visitor. That allows multiple visitors share the same account
of different level.

An option to access DI/DO is provided for each account. Some users
- 24 -

may need to prohibit from controlling your attached devices. You may delete some
3 .
users from ○

4
More flexible options for viewers ○

The first option allows anyone uses “demo” as the user name to view without password.
The Administrator can also decide if more viewers are allowed to watch the video if the
viewers exceed the limit. The overloaded viewers will have snapshot mode instead.

Change homepage layout

How to change the font color
1. Click on “Configuration” on homepage,
2. Click on “Homepage layout” at the left column,
3. Find “Font color” and pull down the list to choose any color you like,
4. Click on “Save” button.
* The font color is better to contrast with the background.

- 25 -

How to change the background
1. Click on “Configuration” on homepage,
2. Click on “Homepage layout” at the left column,
If you want to display simple color without any image,
3. Find “Background graph” and choose “blank”,
4. Find “Background color” and pull down the list to choose any color you like,
5. Click on “Save” button.
* The background color is better to contrast with the font.
If you want to use the image from another web site as background,
3. Find “Background graph” and choose “Url”,
4. Type the URL of the image on the Internet in the edit box, for example,
“http://dgl.microsoft.com/thumbnails/j023/j0235217(t).gif”,
5. Click on “Save” button.
If you want to change the default background image stored in the Network Camera,
3. Find “Background graph” and choose “default”,
4. Click on “Save” button,
5. Prepare an image file with size less than 131000 bytes and rename it to wallppr.jpg,
6. Open an FTP client program and connect to the Network Camera. The user name and
password is as same as the Administrator’s.
7. Transfer wallppr.jpg in local folder to the Network Camera,
8. Close the FTP program and reload the homepage of the Network Camera.

How to change the image logo at the upper left corner of homepage
1. Click on “Configuration” on homepage,
2. Click on “Homepage layout” at the left column,
If you want to remove any logo,
3. Find “Logo graph” and choose “blank”,
4. Click on “Save” button.
If you want to use the image from another web site as logo,
- 26 -

3. Find “Logo graph” and choose “Url”,
4. Type the URL of the image on the Internet in the edit box, for example,
“http://dgl.microsoft.com/thumbnails/j023/j0234430(t).gif”,
5. Click on “Save” button.
If you want to change the default logo stored in the Network Camera,
3. Find “Logo graph” and choose “default”,
4. Click on “Save” button,
5. Prepare an image file with size less than 65000 bytes and rename it to logo.gif,
6. Open an FTP client program and connect to the Network Camera. The user name and
password is as same as the Administrator’s.
7. Transfer logo.gif in local folder to the Network Camera,
8. Close the FTP program and reload the homepage of the Network Camera.
If you want to add hyperlink to the logo image,
3. Find “Logo link” and type the hyperlink in the edit box, for example,
http://www.mywebsite.com,
4. Click on “Save” button.

- 27 -

How to design my own homepage to replace the current one
1. Prepare your own homepage with size less than 65000 bytes and rename it to
user.htm,
2. Insert the html codes of video object, the bold Italian text in the following example,
into the appropriate position in user.htm. Note that the codes of video object must be
copied exactly the same including the letter case.

****** Example homepage begin ******

Example – custom homepage

Network Camera Demo

****** Example homepage end ******

- 28 -

3. Open an FTP client program and connect to the Network Camera. The user name and
password is as same as the Administrator’s.
4. Transfer user.htm in local folder to the Network Camera,
5. Close the FTP program and reload the homepage of the Network Camera,
6. Click on “Configuration” on homepage,
7. Click on “Homepage layout” at the left column,
8. Check “Use the customized homepage”.
9. Click on “Save” button and return to homepage.
* The user.htm only provides plain text content that scripts and URL of external
resources can be used to adorn the homepage. Refer to tutorials of writing HTML and
scripts.

If the customized homepage goes wrong and cannot display, link to the “Homepage
layout” page, “http:///setup/layout.html”, to disable
“Use the customized homepage”.

- 29 -

Build a multimedia web attraction site
Demo on multiple sites – mid-scale service
The Network Camera can allow ten visitors on-line simultaneously. After Installation,
focus the Network Camera on any view you would like friends to share and tell the
visitors to type in the web browser address. Caution:

You may want to maintain your

visitor’s list in the security configuration page to block out unexpected visitors. No need
to have the geeks’ skill and equipments, no need to find suitable software.

Product demo for e-business – large-scale service
If the number of visitors has exceeded the limit, the Network Camera can allow the
"overload" viewers to see the snapshots in JPEG mode, on the homepage.
still images and will be refreshed periodically and automatically.

These are

It needs a script

function supported by the web browser.

1. Click on “Configuration” on homepage,
2. Click on “Security” at the left column,
3. Go to the page bottom and check “Allow more viewers with snapshot mode”,
4. Set the snapshot interval to refresh the still image automatically. The longer the
snapshot interval is, the better the snapshot mode works for more viewers.

- 30 -

If you want to expand to allow in more viewers, the host server should be able to
handle large network traffic, which must handle the picture refreshing from the
Network Camera.
If the web space has FTP service,
Set the Network Camera as an FTP client to upload the pictures. The access to the
Network Camera will be independent of the number of viewers and the picture quality
will remain constant.
1. Click on “Configuration” on homepage,
2. Click on “Network” at the left column,
3. Fill the FTP related settings including server, user name and password, as well as the
upload path if specified by the web space,
4. Click on save and wait for system restart,
5. Click on “Application” at the left column,
6. Select “Sequential operation” and set the interval,
7. Select FTP without date time suffix as the upload method and click on save,
8. The image file uploaded to the web space is named “video.jpg”. Check if the file is
successfully uploaded to the correct folder,
9. Prepare a homepage with the embedded image reference to the image file uploaded
via FTP in advance.
If the web space has no FTP service,
An auto-refresh homepage can be used to periodically poll the newest image from the
Network Camera. It is most efficient if using a free web space provider as the FTP
service may be limiting.
1. Prepare an auto-refresh homepage like the following example. The URL of image is
http://“IP address of the Network Camera”/cgi-bin/video.jpg. Modify the IP address
according to your Network Camera. Define the refresh interval according to your
network bandwidth for best result. If the refresh rate is too fast and there is a large
number of visitors, this may overload the Network Camera and slows the response.

- 31 -

****** Example homepage begin ******

Example - auto refresh

Network Camera Demo

****** Example homepage end ******

- 32 -

height="'+imgheight+'"

Build a security application
The Administrator can use the built-in motion detection to monitor any movement to
perform many useful security applications. To upload the snapshots, users can choose
either email or FTP according to user’s needs. Both e-mail and FTP use the network
settings on the network page. Refer to the definition section for detail configuration.
1. Click on “Configuration” on homepage,
2. Click on “Motion detection” at the left column,
3. Check “Enable motion detection”,
4. Click on new to have a new window to monitor video,
5. Type in a name to identify the new window,
6. Use the mouse to click, hold, and drag the window corner to resize or the title bar to
move,
7. Fine-tune using the “Sensitivity” and “Percentage” fields to best suit the camera’s
environment. Higher ”Sensitivity” detects the slighter motion. Higher “Percentage”
discriminates smaller objects,
8. Clicking on “Save” enables the activity display. Green means the motion in the
window is under the watermark set by Administrator and red means it is over the
watermark,
9. Click on “Application” at the left column,
10.Check the weekdays as you need and give the period of "Snapshots begin" time
and "Snapshots end" time to monitor the motion detection every day,
11.Check the “Send out the snapshot while motion detection”.
12.Set the delay before detecting next motion to avoid continuous false alarms
following the original event,
13.Set the delay to take snapshots after motion to capture the direction of the
moving objects,
14.Check the window name set in step 5,
15.Check the way to upload snapshot,
16.Click on save to validate.

- 33 -

Software revision upgrade
Customers can obtain the up-to-date software from the web site. An easy-to-use
Upgrade Wizard is provided to upgrade the Network Camera with just a few clicks. The
upgrade function is opened to the Administrator only. To upgrade the system, follow
the procedures below.
1. Download the firmware file named “FLASH.BIN” from the appropriate product folder.
2. Run the Upgrade Wizard and proceed following the prompts. Refer to the
instructions of the Upgrade Wizard for details.
3. The whole process will finish in a few minutes and it will automatically restart the
system.

If power fails during the writing process of Flash memory, the program in the
memory of the Network Camera may be destroyed permanently. If the Network
Camera cannot restart properly, ask your dealer for technical service.

- 34 -

Definitions in Configuration
Only the Administrator can access system configuration. Each category in the left
column will be explained in the following pages. The bold texts are the specific phrases
on the Option pages. The Administrator may type the URL below the figure to directly
enter the frame page of configuration. If the Administrator also wants to set certain
options through the URL, read the reference appendix for details.

http:///setup/config.html
is the domain name or original IP address of the Network Camera.

- 35 -

System parameters
"Keep current date and time" Click on this to reserve the current date and time of
the Network Camera. An internal real-time clock maintains the date and time even
when the power of the system is turned off.
"Sync with computer time" Synchronizes the date and time of the Network Camera
with the local computer. The read-only date and time of the PC is displayed as updated.
“Manual” Adjust the date and time according to what is entered by the Administrator.
Notice the format in the related fields while doing the entry.
“Automatic” Synchronize with the NTP server over the Internet whenever the
Network Camera starts up. It will fail if the assigned time-server cannot be reached.
“NTP server” Assign the IP address or domain name of the time-server. Leaving the
text box blank connects the Network Camera to the default time-servers.
"Time zone" Adjust the time with that of the time-servers for local settings.
Remember to click on

to immediately validate the changes. Otherwise, the

correct time will not be synchronized.

- 36 -

Security settings
“Root password” Change the Administrator’s password by typing in the new
password identically in both text boxes. The typed entries will be displayed as asterisks
for security purposes. After pressing

, the web browser will ask the Administrator

for the new password for access.
“Add user” Type the new user's name and password and press

to insert the new

entry. The new user will be displayed in the user name list. There is a maximum of
twenty user accounts.
“Delete user” Pull down the user list to find the user’s name and press

complete.
“Allow ‘demo’ account to view” Click this to permit anyone who types in “demo” as
user name. No password is needed for demo account. Note that a demo account is
restricted to view only.
“Allow more viewers with snapshot mode” There can only be a maximum of 10
users to simultaneously view the video.

This option allows for the 11th viewer on, the

overloaded viewers, to see only still images. These still images are automatically
refreshed by the interval defined below. This feature must be supported by the java
script capability of the web browsers.
“Snapshot interval” defines the refresh rate of the still image in the homepage seen
by the overloaded viewers.

- 37 -

Network settings
Any changes made on this page will restart the system in order to validate the changes.
Make sure every field is entered correctly before clicking on

"Reset IP address at next boot", the default status is checked to get IP address
automatically at the server start. Therefore, once the network settings, especially the
IP address, have been entered correctly, uncheck this option.

General
“IP address” This is necessary for network identification.
“Subnet mask” This is used to determine if the destination is in the same subnet. The
default value is “255.255.255.0”.
“Default router” This is the gateway used to forward frames to destinations in a
different subnet. Invalid router setting will fail the transmission to destinations in
different subnet.
“Primary DNS” The primary domain name server that translates hostnames into IP
addresses.
“Secondary DNS” Secondary domain name server that backups the Primary DNS.

SMTP
When the SMTP server support SMTP authentication, users need to give the valid user
name and password to send email via the server.
“SMTP (mail) server 1” The domain name or IP address of the external email server.
“User name of SMTP 1” This granted user name on the external email server.
“Password of SMTP 1” This granted password on the external email server.
“Recipient email address 1” The email address of the recipients for snapshots or log
file. Multiple recipients must be separated by semicolon, ‘;’.
“SMTP (mail) server 2” The domain name or IP address of another email server once
the previous server is unreachable.
“User name of SMTP 2”, granted user name on the backup email server.
“Password of SMTP 2”, granted password on the backup email server.
- 38 -

“Recipient email address 2” The email address of the recipients for the backup
server.
“Sender email address”, the email address of the sender.

FTP
“Local FTP server port” This can be other than the default port 21. The user can
change this value from 1 to 65535. After the changed, the external FTP client program
must change the server port of connection accordingly.
“1st FTP server” The domain name or the IP address of the external FTP server. The
following user settings must be correctly configured for remote access.
“1st FTP user name” Granted user name on the external FTP server.
“1st FTP password” Granted password on the external FTP server.
“1st FTP remote folder” Granted folder on the external FTP server. The string must
conform to that of the external FTP server. Some FTP servers cannot accept preceding
slash symbol before the path without virtual path mapping. Refer to the instructions for
the external FTP server for details. The folder privilege must be open for upload.
“Primary FTP passive mode” The Network Camera is located inside the network
protected by a firewall, data connection for FTP may be prohibited. By selecting passive
mode, the FTP can bypass the rule and allow snapshot upload to proceed. If the passive
mode is selected, the Network Camera can automatically attempt for active mode, if
the external FTP server does not support passive mode.
“2nd FTP server” The domain name or IP address of the external FTP server.
“2nd FTP user name” Granted user name on the backup FTP server.
“2nd FTP password” Granted password on the backup FTP server.
“2nd FTP remote folder” Granted folder on the backup FTP server.
“Secondary FTP passive mode” Passive mode setting for the backup FTP server.

HTTP
“Http port” This can be other than the default Port 80. Once the port is changed, the
users must be notified the change for the connection to be successful. For instance,
when the Administrator changes the HTTP port of the Network Camera whose IP
address is 192.168.0.100 from 80 to 8080, the users must type in the web browser
“http://192.168.0.100:8080” instead of “http://192.168.0.100”.
- 39 -

Streaming
“Control channel port” This can be something other than the default port 5001 in
order to work with the port opened by the firewall.
“Audio channel port” This can be something other than the default port 5002 in
order to work with the port opened by the firewall.
“Video channel port” This can be something other than the default port 5003 in
order to work with the port opened by the firewall.
“Improve audio quality in low bandwidth environment” If the Network Camera
seems to work in a low bandwidth network environment, the user can use this option
to see if audio quality can be improved by sacrificing some real-time synchronization.
“Mute” This can force the transmission protocol to HTTP and disable audio.

Some invalid settings may cause the system failing to respond. Change the
configuration only if necessary and consult with your network supervisor or experienced
users for correct settings. Once the system has lost contact, refer to Appendix A for reset
and restore procedures.

- 40 -

DDNS and UPnP settings
“Enable DDNS” This option turns on the DDNS function.
“Provider” The provider list contains four hosts that provide DDNS services. Please
connect to the service provider’s website to make sure the service charges.
“Host name” If users wants to use DDNS service, this field must be filled. Please input
the hostname that is registered in the DDNS server.
“Username/E-mail” The Username or E-mail field is necessary for logging in the
DDNS server or notify users of the new IP address. Note: when this field is input as
“Username” the following field must be input as “Password”.
“Password/Key” Please input the password or key to get the DDNS service.
“Enable UPnP” This turns on or off the UPnP function. When UPnP is turned off, the
camera cannot be found through network neighbors in MS Windows XP. If the UPnP
network component is installed in Windows XP, the hostname of the Network Camera
will be shown with bracketed IP address in the Network neighbors. Ex: Network
Camera (192.168.0.96). That is: The hostname of the Network Camera is “Network
Camera”, and the IP address of the Network Camera is 192.168.0.96.
“Save” Click on the button to save current settings for the DDNS service and UPnP
function.
Network Camera provides a free DDNS service. Administrators can choose safe100.net
in the “Providers” field to use it. At the first time, Administrators must register an
account for it.

Video codec parameters
“Text on video” The text will be displayed in the black bar above the video window
with a timestamp. The timestamp is captured from the date and time of the Network
Camera that is maintained by a built-in real-time clock.
“Color” Select either for color or monochrome video display.
“Size” There are five options for three video sizes. “Half” is the quarter size of
“Normal”. “Half x 2” has the same video size as “Normal” but of a lesser quality,
while consuming less network bandwidth. “Normal” is the quarter size of “Double”.
“Normal x 2” has the same video size as “Double” but of a lesser quality, while
consuming less network bandwidth.
- 41 -

“Power line frequency (for fluorescent light)”, the fluorescent light will flash
according to the power line frequency that depends on local utility. Change the
frequency setting to eliminate uncomfortable flash image when the light source is only
fluorescent light.
There are three dependent parameters provided for video performance adjustment.
“Maximum frame rate” This limits the maximal refresh frame rate, which can be
combined with the “Video quality control” to optimize bandwidth utilization and
video quality. If the user wants to fix the bandwidth utilization regardless of the video
quality, choose “Fix bit rate” and select the desired bandwidth. The video quality may
be poor due to the sending of maximal frame rate within the limited bandwidth when
images are moving rapidly. Consequently, to ensure

detailed video quality

(quantization rate) regardless of the network, it will utilize more bandwidth to send the
maximal frames when images change drastically.
“Flip” Vertically rotate the video.
“Mirror” Horizontally rotate the video. Check options both if the Network Camera is
installed upside down.
“White balance” Adjust the value for best color temperature.
Click on this button to pop up another window to tune “Brightness”,
“Contrast”, “Hue” and “Saturation” for video compensation. Each field has eleven
levels ranged from -5 to +5. In “Brightness” and “Contrast” fields the value 0
indicates auto tuning. The user may press
image is O.K., press

to set the image settings.

original settings without incorporating the changes.

- 42 -

to fine-tune the image. When the
Click on this to recall the

- 43 -

Motion detection
“Enable motion detection” Check this option to turn on motion detection.
Click on this button to add a new window. At most three windows can exist
simultaneously. Use the mouse to click, hold, and drag the window frame to resize or
the title bar to move. Clicking on the ‘x’ at the upper right-hand corner of the window
to delete the window. Remember to save in order to validate the changes.
Click on this button to save the related window settings. A graphic bar will rise or
fall depending on the image variation. A green bar means the image variation is under
monitoring level and a red bar means the image variation is over monitoring level.
When the bar goes red, the detected window will also be outlined in red. Going back to
the homepage, the monitored window is hidden but the red frame shows when motion
is detected.
"Window Name" The text will show at the top of the window.
“Sensitivity” This sets the endurable difference between two sequential images.
“Percentage” This sets the space ratio of moving objects in the monitoring window.
Higher sensitivity and small percentage will allow easier motion detection.
The following figure shows the screen when

is clicked. The monitoring window

has been outlined in red and the graphic bar goes red since the goldfish is moving.

- 44 -

Application settings
Weekly schedule
“Sun” ~ “Sat” Select the days of the week to perform the following operations.
“Snapshots begin at” Set the time to start operations.
“Snapshots stop at” Set the time to stop operations.
Setting identical begin time and stop time means 24-hour operation.
“All the time except for the above schedule” Set the schedule all the time except
for the above in a week.

Send out the snapshot while motion detection
“Delay second(s) before detecting next motion” Set the time delay before
restarting to check on the triggering condition when the current condition is triggered.
“Take snapshots at second(s) after motion” After the camera has taken a
snapshot when a condition is triggered, another snapshot will be taken after this
configured interval, in seconds.
“Trigger condition” There are three windows for motion detection each can be
assigned a name. If motion detection has not been set up, “undefined” will be shown
instead of the window title. If this happens, clicking on “Motion detection” and a note
will show to direct the User to the configuration page for motion detection.

Sequential operation
“Snapshot every second(s)” The Network Camera will send snapshots at the
specified intervals to the external server using the method selected below. Remember:
This operation is still subject to the conditions set in the weekly schedule.
“Send snapshots by email” This selects the uploading method following the
intervals set above. The snapshot named “video.jpg” will be attached in the email with
the subject title “Periodic snapshots”.
“Send snapshots by FTP” The snapshots will be uploaded to the external FTP server
with the file name defined in the next option. This can also be used to refresh the
- 45 -

captured images stored in the external web server to build creative homepages.
“FTP put snapshots with date and time suffix” This option sets up the snapshot
capture date and time, which can be used to easily differentiate the snapshot file
names

either

the

sequential

event

operation.

For

instance,

“video@20030102030405.jpg” means the JPEG image was captured in the year 2003,
January the 2nd, at 3 o’clock, 4 minute, and 5 second. If this suffix is omitted, the file
named “video.jpg” on the external FTP server will be refreshed at the specified interval.

- 46 -

Homepage layout settings
“Use the customized homepage”, check this option to use “user.htm” uploaded by
the Administrator instead of the default one. Refer to the section “Administrator’s
capability” for detail usage. The following options related to the default homepage will
not affect the “user.htm”.
“Logo graph”, the logo located at the upper left corner of homepage can be hidden,
the default one that can be changed by the Administrator, or any image on the Internet
that can be located via URL. The default logo is stored in memory and can be changed
by FTP. The maximal size is 32000 bytes. Though the file name is fixed to “logo.gif”, the
image can be any file format as long as the web browser can read it. Refer to the
section “Administrator’s capability” for how to change the default logo.
“Logo link”, when users click on the logo image, a new window will pop up to show
the homepage of the given URL. Clear the URL will disable the link function.
“Background graph”, the background image can be hidden to show the background
color only, the default one that can be changed by the Administrator, or any image on
the Internet that can be located via URL. The default background image is stored in
memory and can be changed by FTP. The maximal size is 131000 bytes. Though the file
name is fixed to “wallppr.jpg”, it can be any file format as long as the web browser can
read it. Refer to the section “Administrator’s capability” for how to change the
background image.
”Font color", pull down the list to select any color for the text in the homepage.
”Background color", pull down the list to select any color for the homepage
background. It can be seen when the background image is not displayed.

- 47 -

Viewing system log
Click the link on the configuration page to view the system log file. The content of the
file provides useful information about configuration and connection after system bootup.

Viewing system parameters
Click on this link on the configuration page to view the entire system’s parameter set.
The content is the same as those in CONFIG.INI.

Factory default
Click on this link on the configuration page to restore the factory default settings. Any
changes made so far will be lost and the system will be reset to the initial factory
settings. After clicking on the “OK” button and make confirmation, the system will
restart and require the installer program to set up the network again.

- 48 -

Appendix
A. Troubleshooting
Status LED
After powering up, the Network Camera performs a self-diagnostic to detect any
hardware defects. The following table lists the LED patterns in general. In case of any
fatal error, the LED will blink in a pattern other than those below.
Condition

LED color

During self-diagnostic after power on

Blink in interchanged green and red

Ethernet signal is lost

Steady red till Ethernet is detected

Before network is setup

Steady green till IP address is confirmed

After network is setup

Blink green every second

Network is setup and audio is disabled

Blink green every 4 seconds

Any hardware failure

Other patterns

Reset and restore
button in the back of the Network Camera. It is used to reset the
system or restore the factory default settings. Sometimes
resetting the system sets the system back to normal state. If the
system problems remain after reset, restore the factory settings
and install again.
RESET:

Click on the button.

RESTORE:

1. Press on the button continuously.

2. Wait for self-diagnostic to run twice.
3. Free the button as soon as the second self-diagnostic starts.
Restoring the factory defaults will erase any previous settings. Reset or restore the
There
is
a
system
after power
on.

- 49 -

B. Frequently asked questions
Q What if I forget my password?
A After the Administrator's password is assigned, every access to the Network Camera
needs authentication. If you are one of the managed users, you have to ask the
Administrator for the password. If you are the Administrator, there is no way to recover
the root password except for restoring factory default. Refer to Appendix A for the
procedures.
Q Why can I not watch video from the Network Camera after it is authenticated?
A There are many possible scenarios regarding this problem,
1. If you have just installed the Network Camera and are unable to watch the video,
check if the heartbeat LED is blinking or the lens cap is removed. If the heartbeat LED
is dim, perform the software installation again.
2. If the Network Camera is well installed and you are accessing the Network Camera
for the first time using Internet Explorer, adjust the security level of Internet Explorer
to allow installation of plug-ins.
3. If the problem still exists after adjusting, and the message over the image window
is showing "connecting", the network traffic may be too crowded.
Q What is the plug-in for?
A The plug-in provided by the Network Camera is used to display motion pictures and
audio in Internet Explorer. If your system does not allow installation of any plug-in
software, the security level of the web browser may need to be lowered. It is
recommended that you consult your network supervisors in your office regarding
adjustment of the security level. Software installation may be regulated in some
offices.
Q Why is the timestamp different from the system time of my PC or notebook?
A The timestamp is based on the system time of the Network Camera. It is maintained
by a real-time clock inside and can be automatically synchronized with the time server
if the Network Camera is connected to the Internet and the function is enabled.
Differences of several hours may result from the time zone setting.

- 43 -

Q Can I install it on ceiling?
A Yes. There are flip and mirror options in video configuration page to correct the
images for upside down installation.
Q The image is not clear enough.
A Rotate the lens to adjust the focus after the Network Camera is installed in the proper
position. The image settings and white balance can be fine tuned to achieve the best
visual effect. Also notice the power line frequency must match the local utility to
synchronize and minimize the effect of flickering florescent lights.
Q Why does the image not refresh regularly?
A Some anti-virus programs filter the received web content. It takes time to perform
data examination and affect the streaming application such as the Network Camera.
However it only affects the HTP mode of the Network Camera. If the network allows
only HTTP mode, disable the web filtering function of the anti-virus program
temporarily. During the period, users should be aware of the risk of malicious network
activity.
Q I have opened motion detection windows but it cannot work.
A If the motion detection windows are setup and names are given, check to see if the
function is checked at the first line. While it is enabled, adjust the sensitivity and
percentage to monitor the level indicator for best results.
Q I cannot hear any sound while watching.
A If there is "V_ONLY" shown above the image, click on connection type to uncheck
"Disable audio". If there is "V" shown instead of "AV", the sound card in your PC may
not properly installed. If "AV" is shown, check the audio source of the Network Camera.
Q How many users are allowed to watch the Network Camera at the same time?
A Too many users requesting the real-time multimedia content will jam the network.
For best results, the Network Camera is designed to accommodate maximum ten (10)
users to watch and listen to the Network Camera at the same time. For a larger number
of users, it is recommended to build another web server to host the retrieving contents
from the Network Camera.

- 44 -

Q How fast is the video rate of the Network Camera?
A The MPEG4 codec engine can process 30 frames per second internally. However the
total performance is subject to many coefficients as follows:
1. Network throughput,
2. Bandwidth share,
3. Number of users,
4. The complicated/detailed objects and movement in view,
5. The level of your PC or notebook computer that is responsible for displaying images.
In general, the transfer rate in a general local network environment can achieve over
200 kilobytes per second and approximately 10 to 20 pictures per second from a
regular environment.
Q How can I keep the Network Camera as private as possible?
A The Network Camera is designed for surveillance purposes and has many flexible
interfaces. The user authentication and special confirmation in installation can keep the
Network Camera from unauthorized access. You may also change the HTTP port to
non-public number. The demo account is good to separate guests from normal users
and thus you can easily block guests anytime. You can check the system log to examine
any abnormal activities and trace the origins.
Q Why can I not access the Network Camera when I setup some options in the
application?
A Since the Network Camera is a "network device", any incorrect network settings will
make it unreachable. If this happens, restore the factory default settings following the
procedures in Appendix A.

- 45 -

C. URL commands of the Network Camera
For some customers who already have their own web site or web control application,
the Network Camera can be easily integrated through convenient URLs. This section
lists the commands in URL format corresponding to the basic functions of the erase
Network Camera.

Capture update Snapshot of JPEG image
/cgi-bin/video.jpg?size=
The Network Camera will return the most up-to-date snapshot in JPEG format. The
value of size can be 1, 2 and 3. 1 means half, 2 means normal and 3 means double. If
users do not set the size in this command, the snapshot size will be the same as the
setting of video option.

Query status of the digital input
/cgi-bin/getdi.cgi
The Network Camera will return the status of digital input.

Drive the digital output
/cgi-bin/setdo.cgi?do=
The state is either “H”, or “L”.”H” means high, that is NC is connected with COMMON and
“L” means low that is NO is connected with COMMON.
For instance, typing http://192.168.0.201/cgi-bin/setdo.cgi?do=h in the address bar
of the web browser will command the Network Camera, with IP address of
192.168.0.201, to set digital output to connect to NC with COMMON.

- 46 -

Restore factory default settings
/setup/restore.cgi
The Network Camera will automatically restart after restoring factory default
configurations.

Restart system
/setup/reset.cgi
Restart the Network Camera without warning.

- 47 -

Page URL
The configuration page has a frame layout including an option list frame and an option
page frame. Referenced URLs, except for the configuration page, direct users to the
option page frame only. Some pages, such as image quality setting and preset setting,
are opened in new windows for preview.
Only the Administrator can access these URLs.
Homepage name

Referenced URL

connection type page

/client.html

configuration page

/setup/config.html

system option

/setup/system.html

security option

/setup/security.html

network option

/setup/network.html

DDNS and UPnP option

/setup/ddns.html

video option

/setup/video.html

motion detection

/setup/motion.html

image quality option

/setup/image.html

application option

/setup/app.html

homepage layout option

/setup/layout.html

system log

/setup/logfile.html

system parameters

/setup/parafile.html

set factory default

/setup/factory.html

System resource URL
There are some images used on the homepage when the homepage layout is in image
mode. The Administrator may use the following links to show the images saved in the
Network Camera on another page.
Resource name

Referenced URL

system logo image

/pic/logo.gif

background image

/pic/wallppr.jpg

- 48 -

General format of command URL
Every configuration can be set through URL with POST method by the Administrator
only.

URL[?[name=value][&name=value]……]

POST

root

System configuration URL
URL:

/setup/system.cgi

NAME

VALUE

DESCRIPTION

host

method

date

keep

keep date and time unchanged

auto

use NTP server to synchronize

manu

directly adjust date and time

year, month and date separated by
slash

time

hour, minute and second separated
by colon

ntp

NTP server

zone

-12 ~ 12

time zone, 8 means GMT +8:00

- 49 -

Security configuration URL
URL:
NAME

/setup/security.cgi
VALUE

DESCRIPTION

rootpass
username
userpass
deluser

action

validate demo users with “open”

open

yes

grant for demo account

prohibit for demo account

Yes

allow more guests with snapshot

slow

mode
no

forbid more guests with snapshot
mode

selay

0 ~ 99

snapshot interval

Network configuration URL
URL:

/setup/network.cgi

NAME

VALUE

DESCRIPTION

reset

yes

enable installation at next boot

disable installation at next boot

Network Camera's IP address

subnet

subnet mask

router

default gateway

dns1

primary DNS server

dns2

secondary DNS server

- 50 -

smtp1

primary SMTP server

smtp1Usr

smtp1pass
mail1

smtp2

secondary SMTP server

smtp2Usr

smtp2pass
mail2

retmail

ftpp

FTP port

ftp1

primary FTP server

ftpuser1

ftppass1

ffd1

Pasv1

yes

access FTP server in passive mode

access FTP server in active mode

ftp2

secondary FTP server

ftpuser2

ftppass2

ffd2

Pasv2

yes

access FTP server in passive mode

- 51 -

access FTP server in active mode

http

HTTP port

cport

control Channel port

aport

audio Channel port

vport

video Channel port

band

yes

optimal for the low bandwidth

keep the original way

yes

disable audio

enable audio

mute

DDNS & UPnP configuration URL
URL:

/setup/ddns.html

NAME

VALUE

DESCRIPTION

enddns

anything

Enable DDNS function. This option
must be resent whenever the URL is
called, if DDNS function is to be
enabled.

provider

host

DynDNS.org(Dynamic)

DynDNS.org(Custom)

TZO.com

dhs.org

hostname

the

Network

Camera

usermail

or the email address registered in
DDNS server.

passkey
enupnp

or the key given by the DDNS server.

anything

Enable UPnP function. This option
must be resent whenever the URL is
called, if UPnP function is to be
enabled.

- 52 -

Video configuration URL
URL:

/setup/video.cgi

NAME

VALUE

DESCRIPTION

text

color
size

mode
quality
quan

bitrate

frame

B/W

monochrome

color

half

half x 2

normal

normal x 2

double

50Hz

synchronize with 50Hz utility

60Hz

synchronize with 60Hz utility

fixb

fix bit rate

fix quantization

lowest quality of video

lower quality of video

normal quality of video

higher quality of video

highest quality of video

64000

set bit rate to 64K bps

128000

set bit rate to 128K bps

256000

set bit rate to 256K bps

384000

set bit rate to 384K bps

512000

set bit rate to 512K bps

768000

set bit rate to 768K bps

1000000

set bit rate to 1000K bps

1200000

set bit rate to 1200K bps

set maximum frame rate to 1 fps

- 53 -

flip
mirror
wb

set maximum frame rate to 2 fps

set maximum frame rate to 3 fps

set maximum frame rate to 5 fps

set maximum frame rate to 10 fps

set maximum frame rate to 15 fps

set maximum frame rate to 20 fps

set maximum frame rate to 25 fps

set maximum frame rate to 30 fps

yes

flip image

normal image

yes

mirror image

normal image

auto white balance

fixed indoor(2800K)

fixed fluorescent 1(3600K)

fixed fluorescent 2(4000K)

fixed outdoor(6000K)

Image quality configuration URL
URL:
NAME

/setup/image.cgi
VALUE

DESCRIPTION

brightness <-5 ~ 5>

adjust brightness of image

contrast

<-5 ~ 5>

adjust contrast of image

hue

<-5 ~ 5>

adjust hue of image

saturation <-5 ~ 5>

adjust saturation of image

preview

not save the parameters

restore

recall the original settings

save

save the parameters

- 54 -

Application configuration URL
URL:

/setup/app.cgi

NAME

VALUE

DESCRIPTION

emode

Upload

snapshot

when

motion

detected
smode

sequential mode application

smethod mail

upload snapshots by email

ftp

upload snapshots by FTP

suffix

FTP file with date and time suffix

delay

seconds delay to detect next event

inter

seconds delay to capture post-event

motion1

< not required >

set

motion

window1

trigger

window2

trigger

window3

trigger

condition
motion2

< not required >

set

motion

condition
motion3

< not required >

set

motion

condition
sinter

seconds interval for sequential mode

sbegin

time to start sequential mode

send

time to stop sequential mode

Homepage layout configuration URL
URL:

/setup/layout.cgi

NAME

VALUE

DESCRIPTION

cuslogo

blank

hide logo

def

use default logo

url

use image from URL

logourl

linkurl

- 55 -

cusback blank

backurl

hide background image

def

use default background

url

use image from URL

fcolor

<0 ~ 15>

color index for font

bcolor

<0 ~ 15>

color index for background

- 56 -

D. Technical specifications
- System

- Audio

CPU: Trimedia PNX1300
RAM: 16MB SDRAM
ROM: 2MB FLASH ROM

Bite rate: 24Kbps
Supporting audio mute

- Microphone
- Networking
Protocol
TCP/IP, HTTP, SMTP, FTP, DDNS, UPnP , Telnet, NTP,
DNS and DHCP
Physical
10 baseT or 100 baseT Fast Ethernet auto negotiation

Omni-directional
Frequency: 50 – 16000Hz
S/N ratio: more than 60dB

- LED indicator
Dual color status indicator

- Dimension

- Video
Algorithm supported
MPEG4(short header mode) for streaming video JPEG
for still image
Features
Adjustable image size, quality and bit rate
Time stamp and text overlay
3 motion detection windows
Resolution
Up to 30/25 frames at 160x120
Up to 30/25 frames at 320x240
Up to 10 frames at 640x480

28.6mm(D) * 72.8mm(W) * 115.2mm(H)

- Weight
NET. 215g

- Power
Input: 100-240VAC, 50/60Hz, 0.4A
Output: 5VDC, 2A

- Operating Environment
Temperature: 0-50°C/32-122°F
Humidity: 95%RH

- EMI & Safety

- Camera Specification

CE, FCC

1/4 inch color CMOS sensor
Resolution: 640x480
AGC, AWB, AES
Electronic shutter: 1/60 ~ 1/15000 second

- Viewing system requirement
Operating system
Microsoft Windows 98SE/ME/2000/XP
Browser
Internet Explorer 5.x or above

- Lens
Fixed focal with fine tuning, 4.0mm, F2.0

- 57 -

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2004:12:09 12:17:58Z
Modify Date                     : 2004:12:13 19:11:46+08:00
Page Count                      : 73
Creation Date                   : 2004:12:09 12:17:58Z
Mod Date                        : 2004:12:13 19:11:46+08:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : Claudia
Metadata Date                   : 2004:12:13 19:11:46+08:00
Creator                         : Claudia
Title                           : Microsoft Word - FCS-1030 User's Manual.doc

EXIF Metadata provided by EXIF.tools

Levelone Fcs 1030 Users Manual User's

FCS-1030 to the manual ead9f89c-1f7f-4809-bc55-10630c3b945b

Navigation menu

Versions of this User Manual:

Views

Navigation