Levven Automation WOWSW1 Wireless Light Switch Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2432999
Application ID	lPMJekj7aAHp7CicKEWZUg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	92.26kB (1153188 bits)
Date Submitted	2014-10-31 00:00:00
Date Available	2015-02-19 00:00:00
Creation Date	2014-09-25 12:28:57
Producing Software	Microsoft® Word 2010
Document Lastmod	2014-09-25 12:28:57
Document Title	User Manual
Document Creator	Microsoft® Word 2010
Document Author:	Tony

Levven Automation Inc.
9741 - 54th Ave NW, Edmonton
Alberta, Canada T6E 5J4
Phone: (780) 391-3000
Fax:
(780) 391-3001
Wireless Light Switch User Manual (Draft)
1 System description
The wireless light switch system is designed to wireless turn lights on or off from anyway in a house,
which contains two components: switch and controller.
The Switch is a thin, wall mount switch that looks and feels much like a normal decora switch and fits in
a normal decora faceplate. It is battery-powered and transmits commands in a secured way to
controllers when a user pushes a button.
The Controller is an action component that receives commands from remote switches and takes action
accordingly. It is installed in the junction box to a lighting fixture connected with phase, neutral and
control wires. The switch to controller can be point to point (one switch controlling one controller) or
multi point to multi point (multi switches signaling one or more controllers).
1-9
Levven Automation Inc.
9741 - 54th Ave NW, Edmonton
Alberta, Canada T6E 5J4
Phone: (780) 391-3000
Fax:
(780) 391-3001
2 Specifications
2.1 Switch
1.
2.
3.
4.
5.
6.
Dimensions………………………………………………………………………..…105mmx36mmx11.2mm
Battery…………………………………………………………………………………………………………….CR2032
Wireless frequency…………………………………………………………….……………………..…….917Mhz
Wireless range..................................................................Up to 100 meters line of sight
Operating Temperature.........................................................................................0-40°C
Indoor use only
2.2 Controller
1.
2.
3.
4.
5.
6.
7.
Dimensions…………………………………………………….……..……………..56mmx47.7mmx39.6mm
Voltage………………………………………………………………………………………..………..120VAC, 60Hz
Maximum load…………………………………………………………………………..……………………….600W
Wireless frequency…………………………………………………………….……………………..…….917Mhz
Wireless range..................................................................Up to 100 meters line of sight
Operating temperature.........................................................................................0-40°C
Load type……………………………….Incandescent, halogen and other resistive light fixtures
2-9
Levven Automation Inc.
9741 - 54th Ave NW, Edmonton
Alberta, Canada T6E 5J4
Phone: (780) 391-3000
Fax:
(780) 391-3001
8. Indoor use only
3 Features








Compatible for incandescent, halogen and other resistive light fixtures
Non-relayable wireless lighting control
On-Off controller
Battery powered switch operable up to 10 years*
Ease of multiple-way control
o Each switch can control as many as possible controllers, as long as they are within the wireless
range
o Each controller controllable by up to 10 switches
Advanced security level
o Rolling code to prevent repeat attack
o 128-bit encryption
Ease of installation (No wiring between controller and switch, and a switch can be attached to
anywhere)
Switch dimmer function ready
*Conditions apply: typical operation 100 switches per day, average 0.5 second press and hold time, 20°C.
Actual battery life greatly depends on usage environment, such as temperature and humidity, and
operation conditions, such as press and hold time.
4 Installation Instructions
WARNINGS:
• To be installed and/or used in accordance with local electrical codes and regulations.
• The controller should be mounted to a listed electrical junction box of suitable size with height
no less than 2” (50.8mm) and with ½” knockouts, such as
⁄ Octagonal box.
• If you are unsure about any part of these instructions, consult a qualified electrician.
NOTE: Use check boxes
Step 1

Step 2

 when Steps are completed.
WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN OFF POWER at circuit breaker or fuse
and test that power is off before wiring!
Identifying your wiring application, these wires in a junction box are needed
1. Line/hot
2. Neutral
3-9
Levven Automation Inc.
9741 - 54th Ave NW, Edmonton
Alberta, Canada T6E 5J4
Phone: (780) 391-3000
Fax:
(780) 391-3001
3. Load (to light fixture)
Step 3

Mount the controller inside a suitable junction box:
The controller is normally installed inside a junction box that supports light fixtures. Insert
its connector coupling into a ½” knockout from inside, with the antenna stretching out
from the hole as well.
4-9
Levven Automation Inc.
9741 - 54th Ave NW, Edmonton
Alberta, Canada T6E 5J4
Phone: (780) 391-3000
Fax:
(780) 391-3001
Step 4

Wiring controller:
 Connect (Neutral) wire from junction box to white wire on controller
 Connect (Line/hot) wire from junction box to black wire on controller
 Connect (Load) wire from junction box to red wire on controller
Line/Hot
(Red)
(Black)
Antenna
Controller
Load
(White)
Neutral
Step 5

Step 6

Step 7
Power on the controller
 The green LED on the controller will be lit
 The red LED will indicate controller status: it is on indicating the circuit to the light
fixture is connected; it is off indicating the circuit to the light fixture is disconnected
Pairing switch with controller:
 On the controller, press “PAIR” button. The LED on the controller will begin flash green
slowly
NOTE: If there is no pairing request received within 60 seconds, the controller will quit
the pairing procedure and the LED will go back to solid status automatically
 Press both switch buttons. You may need to push hard to let them contact the bottom
of the switch. When it is activated, the LED on the controller will begin flash green and
red rapidly
 Press “PAIR” on the controller again to confirm the pairing. The LED will flash green
rapidly for a while to indicate success, then stop flashing and go back to solid status
NOTE: If no confirmation operation is performed within 60 seconds, the controller will
quit the pairing procedure and the LED will go back to solid status automatically
 Pairing procedure end

You are ready to go now.

5-9
Levven Automation Inc.
9741 - 54th Ave NW, Edmonton
Alberta, Canada T6E 5J4
Phone: (780) 391-3000
Fax:
(780) 391-3001
5 Basic operation
ON: Push switch ON (Activate when push down)
OFF: Push switch OFF (Activate when release)
BRIGHTEN*: Push and hold the switch ON button for more than 3 seconds. If the lights are not lit
previously, they are lit up first.
DIM*: Push and hold the switch OFF button for more than 3 seconds. Lights should first be lit up to be
dimmed.
*Optional, only work on dimmer controller.
6 Advanced operations
6.1 Paring
A switch should first be paired to a controller to control it.




On the controller, press “PAIR” button. The LED on the controller will begin flash green slowly
NOTE: If there is no pairing request received within 60 seconds, the controller will quit the pairing
procedure and the LED will go back to solid status automatically
Press both switch buttons. You may need to push hard to let them contact the bottom of the switch.
When it is activated, the LED on the controller will begin flash green and red rapidly
Press “PAIR” on the controller again to confirm the pairing. The LED will flash green rapidly for a
while to indicate success, then stop flashing and go back to solid status
NOTE: If no confirmation operation is performed within 60 seconds, the controller will quit the
pairing procedure and the LED will go back to solid status automatically
Pairing procedure end
*Press controller “CLEAR” button anytime to quite pairing procedure
6.2 Clear all pairing information

On the controller, press and hold “CLEAR” button for more than 5 seconds. The LED on the
controller will flash red rapidly for a while to indicate successfully delete all paired information. Then
the LED will go back to solid status automatically.
*No individual clearance of a single pairing available. You may need to repair all switches later.
6-9
Levven Automation Inc.
9741 - 54th Ave NW, Edmonton
Alberta, Canada T6E 5J4
Phone: (780) 391-3000
Fax:
(780) 391-3001
7 Change switch battery

Open switch rocker using the notch on the rocker edge.

Change the battery
7-9
Levven Automation Inc.
9741 - 54th Ave NW, Edmonton
Alberta, Canada T6E 5J4
Phone: (780) 391-3000
Fax:
(780) 391-3001

Close the rocker.
8 Wireless performance
Actual wireless performance in a home depends on the installation environment, including numbers of
walls between the controller and the switch, the type of construction, etc.
Things to consider regarding RF range:



Each wall or obstacle (i.e., refrigerator, big screen TV, etc.) between the controller and the
switch will reduce the maximum range by approximately 25-30%.
Brick, tile or concrete walls block more of the RF signal than walls made of wooden studs and
plasterboard (drywall).
Devices installed in metal junction boxes will suffer a significant loss of range (approximately
20%) since the metal box blocks a large part of the RF signal.
9 FCC Part 15 Notice
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the manufacturer's instruction manual, may cause interference with radio and
television reception. This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC Rules.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
8-9
Levven Automation Inc.
9741 - 54th Ave NW, Edmonton
Alberta, Canada T6E 5J4
Phone: (780) 391-3000
Fax:
(780) 391-3001
2) This device must accept any interference received, including interference that may cause
undesired operation.
Notice: The FCC regulations provide that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate this equipment.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference with radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into a different outlet so that the equipment and the receiver are on
different branch circuits.
Consult the dealer or an experienced radio/television technician for help.
9-9

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 9
Language                        : en-CA
Tagged PDF                      : Yes
Author                          : Tony
Creator                         : Microsoft® Word 2010
Create Date                     : 2014:09:25 12:28:57-06:00
Modify Date                     : 2014:09:25 12:28:57-06:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools