Lezyne USA orporated GPS-V106 SUPER GPS, POWER GPS User Manual

Lezyne USA, Incorporated SUPER GPS, POWER GPS

User Manual

English User ManualREAD ENTIRE MANUAL BEFORE OPERATION to ensure proper use and care of your new Lezyne GPS device.Important DO NOT BECOME DISTRACTED by the device—always operate vehicles in a safe manner. Lezyne USA, Inc. does not accept any liability for injuries or other damages resulng from the use of this product in any circumstances.Lezyne GPS devices have a water resistance rang of IPX7 under IEC standard 60529. Submerging the device is not recommended. If moisture does enter the casing, air out unl completely dry.DO NOT ATTEMPT TO REMOVE ELECTRONICS. Doing so will void warranty.DO NOT OPERATE OR STORE OUSIDE OF TEMPERATURE RANGE (-20–70° C). Baery life may be aected at temperature extremes.Locaon and surroundings may aect GPS signal. For best results, use the device outdoors with an unobstructed view of the sky. It may take up to 120 seconds to acquire GPS signals.This GPS device is not a calibrated measuring tool. It should not be used for surveying purposes. GPS based elevaon measurements may vary. Calorie readings are an esma-on for reference only.CA PROPOSITION 65 WARNING: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproducve harm (California law requires this warning to be given to customers in the State of California). For more info: www.lezyne.com/prop65Warranty In U.S. and U.K., Lezyne GPS devices carry a two (2) year warranty from the original purchase date to the original owner (proof of purchase required). Lezyne Baeries carry a six (6) month warranty from the original purchase date. Lezyne warranes cover any manufacturing defects in materials or workmanship. Issues not covered by warranty include normal wear & tear, improper installaon, aempng to access or modify electronics, damage or failure due to accident, misuse, abuse and/or neglect.For all warranty issues worldwide, please contact the retailer that sold the product. For any warranty quesons contact: warranty@lezyne.comMounting To aach the bike mount:1. Align the shim with the boom of the mount. 2. Aach the mount securely using the two bands.To connect the device to the bike mount:1. Align the tabs on the back of the device with the mount. 2. Press down and turn the device unl it locks into place.Charging Before using your Lezyne GPS device for the rst me, fully charge baery. To charge your device:1. Remove exterior moisture 2. Open USB cover 3. Connect micro USB cable and device to powered USB port. For best results, use the supplied Lezyne cable.If device does not display charging symbol when plugged in, selected USB port may not be powered—try another USB port. Correct USB Seal Installation When charging is complete, ensure USB seal is correctly installed for water resistance:1. Install one side at a me 2. Visually inspect for correct installaon Menu & Pause Screen Button Functions ClickSelectBack UpDownRide screen button functions ClickHoldLightON/OFFScroll LeftON/OFFScroll RightMenuStart/LapPauseOperation Starng a ride:1. Hold the le buon to turn the device ON 2. Wait for GPS to connect 3. Click the boom right buon to start recordingStopping a ride:1. Hold the boom right buon to PAUSE 2. Click the right buons to scroll through the opons 3. Click the ENTER buon to select END 4. Click the ENTER buon again to select SAVENavigang a menu:1. Click the right buons to scroll through the opons 2. Click the ENTER buon to selectMore Information For more informaon on Lezyne products, visit: hp://lezyne.comWEEE Noce & Product Disposal: The symbol of the crossed waste container means that, in accordance with2002/96/EC Waste Electrical and Electronic Equipment Direcve (WEEE),once the product reaches the end of its lifecycle, in the European Union it is subject to special waste disposal. In addion to the present device, this rule is also applied to all items carrying such a symbol. Do not dispose of these products as undierenated urban waste but put away for mate-rial dierenated recycling.CE RF Compliance—Meets the EU Requirements: The equipment complies with the RF Exposure Requirement 1999/519/EC, Council Recommendaon of 12 July 1999 on the limitaon of exposure of the general public to electromagnec elds (0–300 GHz). Changes or modicaons to this product not autho-rized by the manufacturer could void the EMC compliance and negate your authority to operate the product. This product has demonstrated EMC compliance under condions that included the use of compliant peripheral devices and shielded cables between sys-tem components. It is important that you use compliant peripheral devices and shielded cables between system components to reduce the possibility of causing interference to radios, televisions, and other electronic devices. We, hereby, declare that this cellular, Wi-Fi radio is in compliance with the essenal requirements and other relevant provi-sions of Direcve 1999/5/EC. Products with CE marking comply with the EMC Direcve (2004/108/EC) and the Low Voltage Direcve (2006/95/EC) issued by the Commission of the European Community. Compliance with these direcves implies conformity to the following European Norms (in parentheses are the equivalent internaonal standards).FCC & IC User Warning Noce: Any changes or modicaons not expressly approved by the party responsible for com-pliance could void your authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:—Reorient or relocate the receiving antenna. —Increase the separaon between the equipment and receiver. —Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.Labelling Requirement Noce: This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operaon is subject to the following two condions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operaon of the device.FCC: 1. This Transmier must not be co-located or operang in conjuncon with any other antenna or transmier.2. This equipment complies with FCC RF radiaon exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cenmeters between the radiatorIC: This device complies with the Canada portable RF exposure limit set forth for an uncon-trolled environment and are safe for intended operaon as described in this manual. The further RF exposure reducon can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such funcon is available.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitaon est autorisée aux deux condions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’ulisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepble d’en compromere le fonconnement.
ID Label Information Instruction FCC ID : 2AD4S-GPS-V106 IC : 20084-GPSV106 How to get the labeling information? Step. 1: Press “MENU” button in several seconds, and into “Main Menu” Step. 2: Use up and down button to select Info word and press “Enter” into “INFO” menu.
(3) Using up and down button, you can select FCC& IC ID information in “INFO MENU”.

Navigation menu