Liebert Universal Monitor Users Manual

Universal Monitor to the manual 3b847744-7f7a-47a0-ac20-862e30f79779

2015-02-09

: Liebert Liebert-Universal-Monitor-Users-Manual-571352 liebert-universal-monitor-users-manual-571352 liebert pdf

Open the PDF directly: View PDF PDF.
Page Count: 144 [warning: Documents this large are best viewed by clicking the View PDF Link!]

MONITORING
UNIVERSAL MONITOR
USER MANUAL
i
TABLE OF CONTENTS
1.0 INTRODUCTION
1.1 Methods of Viewing and Configuring the Universal Monitor . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Data Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.3 Optional Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.4 Available Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.5 Outside Enclosure Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.6 Typical Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.7 Controller Board Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.8 Optional Expansion Board Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.9 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.10 LED Indicators - Optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.11 Typical Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.0 INSTALLATION - MAIN BOARD
2.1 Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1.1 Unpacking and Preliminary Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2 Surface-Mounting the Universal Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2.1 Mounting the Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3 Flush-Mounting the Universal Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.3.1 Mounting the Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.4 Connect Power to the Universal Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4.1 Input Power Connections - Small Enclosure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.4.2 Termination and Mounting - Large Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.4.3 Connecting the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.0 INSTALLATION - OPTIONAL EXPANSION BOARD
3.1 Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.1.1 Unpacking and Preliminary Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2 Surface-Mounting the Optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2.1 Mounting the Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3 Flush-Mounting the Optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.3.1 Mounting the Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4 Input Power Connections - Optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.0 WIRING AND CONNECTIONS - MAIN BOARD
4.1 Wiring Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2 Connecting Digital Inputs and Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2.1 Connecting Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2.2 Connecting Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2.3 Setting the Digital Output Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.3 Connecting Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.3.1 Setting the 12VDC/24VDC Analog Power Jumper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.3.2 Connecting the Analog Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.4 Connecting Common Alarm Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.5 EIA422 SiteScan Web Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.6 Communications Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.6.1 RS232 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.6.2 Phone Line Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
ii
5.0 WIRING AND CONNECTIONS - OPTIONAL EXPANSION BOARD
5.1 Wiring Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.2 Connecting Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.2.1 Connecting Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.2.2 Connecting Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.2.3 Setting the Digital Output DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.3 Connect to the Universal Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.3.1 Connect EIA485 Connectors to Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.3.2 Enable the Connection via Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.0 OVERVIEW OF MENUS
6.1 Opening Screen Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.2 Main Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.3 LCD Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7.0 VIEW STATUS OPTIONS
7.1 View Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.1.1 Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.2 View Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.2.1 Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.2.2 Backing Up the Alarm Log (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.3 View Event Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.3.1 Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.3.2 Backing Up the Event Log (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.4 View Trend Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.4.1 Select a Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.4.2 View a Trend Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.4.3 Backing Up the Trend Log (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . 36
7.5 View Input Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
7.5.1 Input Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
7.6 View Output Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.6.1 Output Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
7.7 View Pager Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.7.1 Select a Pager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.7.2 View a Pager Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.7.3 View a Pager PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
8.0 SILENCE ALARM & BACKUP LOG FILES (SERVICE TERMINAL INTERFACE)
8.1 Silence Alarm (Service Terminal Interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
8.2 Back Up Log Files (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
9.0 SYSTEM AND CONTROL OPTIONS
9.1 Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
9.2 Setup System - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
9.3 Setup System - Setup Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
9.3.1 Change Label (Name of Input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
9.3.2 Define Input as Normally Open or Normally Closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
9.3.3 Define Input as Alarmable or Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
9.3.4 Set Up Alarmable Inputs in Latched or Unlatched Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
9.3.5 Set Up Delay Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
9.4 Setup System - Setup Common Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
iii
9.5 Setup System - Setup Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
9.5.1 Identify the Sensor as Connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
9.5.2 Change Sensor Label (Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
9.5.3 Change Units Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
9.5.4 Change 4 mA Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
9.5.5 Change 20 mA Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
9.5.6 Change Offset Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
9.5.7 Define Sensor as Alarmable or Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
9.5.8 Set Up Alarmable Sensors in Latched or Unlatched Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
9.5.9 Change Low Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
9.5.10 Change High Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
9.5.11 Set Up Delay Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
9.6 Setup System - Setup I/O Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
9.6.1 Set Up Mapping for a Digital Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
9.6.2 Set Up Mapping for an Analog Sensor Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
9.7 Setup System - Setup Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
9.7.1 Change Label (Name of Output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
9.7.2 Define Main Board Output as Normally Open / Closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
9.7.3 Set Expansion Board Output by DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
9.7.4 Configure Main Board Output for Loss of Power (“Fail-Safe”) . . . . . . . . . . . . . . . . . . . . . . . . 59
9.8 Setup System - Setup Modem & Pagers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
9.8.1 Modem Setup - Initialization String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
9.8.2 Modem Setup - Additional Features (Service Terminal Interface only) . . . . . . . . . . . . . . . . . 62
9.8.3 Pager Setup - Pager Number and PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
9.8.4 Pager Setup - Communications Check (Service Terminal Interface only). . . . . . . . . . . . . . . . 66
9.9 Setup System - Setup System Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
9.9.1 Change Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
9.9.2 Change Date & Time/Automatic Daylight Saving Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
9.9.3 Setup Site ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
9.9.4 Connect Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
9.9.5 Backup and Upload Configuration File (Service Terminal Interface only) . . . . . . . . . . . . . . . 71
9.9.6 Setup Serv Ph Num - Enter Phone Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
9.9.7 Setup Serv Ph Num - Communications Check (Service Terminal Interface only) . . . . . . . . . 75
9.9.8 Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.9.9 Perform Firmware Update (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . 76
9.9.10 Initiate Remote Alarm Test (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . 78
9.10 Setup Exp Board - Optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
9.11 Manual Output Ctrl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
9.12 Clear Alarms & Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
9.12.1 Clear Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
9.12.2 Clear the Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
9.12.3 Clear the Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
9.12.4 Clear the Trend Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
10.0 SPECIFICATIONS
10.1 Universal Monitor Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
10.2 Optional Expansion Board Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
iv
APPENDIX A-SERVICE TERMINAL INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
A.1 Comparison of Functions: LCD and Service Terminal Interface. . . . . . . . . . . . . . . . . . . . . . 85
A.2 Connecting to the Service Terminal Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
A.2.1 Connection Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
A.2.2 Create a Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
A.2.3 Set Up the COM1 Port - Direct Connection Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
A.2.4 Set Up the Connection’s Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
A.2.5 Connect to the Service Terminal Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
A.3 Overview of Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
A.3.1 View Status Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
A.3.2 Silence Alarm and Backup Log Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
A.3.3 Setup Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
A.4 View Status Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
A.4.1 View Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
A.4.2 View Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
A.4.3 View Event Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
A.4.4 View Trend Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
A.4.5 View Input Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
A.4.6 View Output Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
A.4.7 View Pager Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
A.5 Silence Alarm & Back Up Log Files (Service Terminal Interface only). . . . . . . . . . . . . . . . 100
A.5.1 Silence Alarm (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
A.5.2 Back Up Log Files (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
A.6 Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
A.6.1 Setup Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
A.6.2 Setup Common Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
A.6.3 Setup Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
A.6.4 Setup I/O Matrix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
A.6.5 Setup Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
A.6.6 Setup Modem & Pagers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
A.6.7 Setup System Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
A.6.8 Connect Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
A.6.9 Override Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
A.6.10 Clear Alarms & Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
APPENDIX B-DEFAULT SETTINGS QUICK REFERENCE GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . .132
v
FIGURES
Figure 1 Small enclosure—external features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 2 Large enclosure—internal features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 3 Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figure 4 Example of typical sequence: Analog input reaches high setpoint . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 5 Mounting Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 6 Electrical connections to panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 7 Power wiring to TM115 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 8 Power wiring to TM230 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 9 Mounting Dimensions - optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 10 Electrical connections to panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 11 Form C output contact wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 12 LCD Menu overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 13 Menu overview - View Status menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 14 Menu overview - System and Control menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 15 Menu overview - Setup System Info menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
TABLES
Table 1 Controller board components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Table 2 Expansion board components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table 3 LED indicators summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 4 LED indicators summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Table 5 Packing manifest - Universal Monitor main board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 6 Packing manifest - optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 7 Wiring specifications - main board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Table 8 Digital output jumper settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 9 Wiring specifications - optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 10 DIP switch setting - outputs wired as Normally Closed (N.C.) . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 11 DIP switch setting - outputs wired as Normally Open (N.O.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 12 Guide to Universal Monitor functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 13 Primary Functions Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 14 Alarm log conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 15 Event log conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 16 Trend log conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table 17 Analog input states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 18 Digital input states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 19 Digital output states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 20 Valid characters for data entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 21 Default settings - digital inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Table 22 Default settings - analog sensor inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table 23 Default mapping of digital inputs to digital outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Table 24 Default mapping of analog inputs to digital outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Table 25 Default settings - digital outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Table 26 Supported modem settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 27 Default settings - modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 28 Country codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Table 29 Pager dialing results. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Table 30 Guidelines for dialing pagers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Table 31 Battery alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
vi
Table 32 Service phone number dialing results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Table 33 Guidelines for dialing service phone number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Table 34 Automatic / manual control - output points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Table 35 Guide to Universal Monitor functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Table 36 Steps to set up a direct or remote connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Table 37 Universal Monitor - default settings for inputs and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Table 38 Universal Monitor - other default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Table 39 Expansion Board - other default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Table 40 Expansion Board - default settings for inputs and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Introduction
1
1.0 INTRODUCTION
The Liebert Universal Monitor’s extensive capabilities can put it at the heart of your protective net-
work. The Universal Monitor employs local alarming and remote paging services to keep personnel
on-site and at remote locations apprised of the status of equipment.
The panel can interface with any device that closes an electrical contact or has a 4-20 mA signal. To
improve process efficiency and troubleshooting, the panel tracks data in three types of logs: alarm,
event and trend. The Universal Monitor has a local LCD interface and a remote dial-up interface.
Further, the Universal Monitor can report ambient conditions that might adversely affect the facility
or equipment and also can report alarms and other events, as well as initiate responses to reduce or
prevent damage.
When an alarm condition arises, the Universal Monitor displays alarm information and sounds an
audible alarm; if configured, the panel also sends pager notifications and turns connected devices on
or off. See 1.11 - Typical Sequence for a more detailed example.
1.1 Methods of Viewing and Configuring the Universal Monitor
The Universal Monitor features remote access through two interfaces that allow users to configure
the panel, silence alarms, back up logs, and perform many other functions to keep a large or small
operation running smoothly and safely.
•LCD—liquid crystal display on the front of the panel
•Service Terminal Interface—accessible via computer connected directly through an RS232
port or remotely through the Universal Monitor’s onboard modem
These interfaces permit easy access and configuration of the Universal Monitor, allowing users to
view data, silence alarms and have full access to information stored in the panel, including logs of
alarms and events.
One more interface—Liebert’s SiteScan Web enterprise monitoring system—is primarily for monitor-
ing, though SiteScan also provides some configuration functions.
1.2 Data Logs
The three types of data logs—alarm history, event history and trend data of analog sensor readings—
can be viewed on the LCD on the front of the Universal Monitor and downloaded through onboard
communications ports.
1.3 Optional Features
An optional Expansion Board, which can be purchased separately, allows you to connect an additional
16 digital inputs and eight digital outputs to the Universal Monitor.
An optional Transformer Module, available only in the large enclosure, converts 115VAC or 230VAC
to 24VAC.
1.4 Available Alarms
The alarms available with the Universal Monitor are:
• Discrete input alarm (for each digital input)
•High setpoint
• Low setpoint
• Battery unplugged
• Low battery
• Loss of power
• Check battery
• Internal modem fault
Two additional alarms are available with the optional Expansion Board:
• Expansion board loss of communications
• Expansion board restore of communications
Introduction
2
1.5 Outside Enclosure Overview
The enclosure for the Universal Monitor’s controller board comes in two sizes:
•The large enclosure is designed to accommodate the Transformer Module and future compo-
nents, in addition to the controller board.
•The small enclosure is built to hold the controller board only.
Both enclosures are 2-3/4" deep.
Both enclosures have a built-in liquid crystal display (LCD) and a key lock, as shown in the example
below. The enclosures are made of metal to accommodate secure conduit fittings and protect compo-
nents against environmental debris.
Figure 1 Small enclosure—external features
The enclosure must be secured to a wall, either flush-mounted or recessed in the wall, as described in
2.0 - Installation - Main Board. Knockouts and access slots on the top and bottom allow easy con-
nection of wires and cables (see 4.0 - Wiring and Connections - Main Board) with either mounting
type.
Figure 2 Large enclosure—internal features
UNIVERSAL MONITOR
05-SEP-02 14:04:13
V5.100.0
PRESS =STATUS/SETUP
ESC
ESC
Universal Monitor
Universal Monitor
LCD for configuration
and operation
Key lock
The enclosure
has knockouts
and access slots
on top and
bottom for
cables and wires.
BAR CODE
BAR CODE
LIEBERT
START
TB7:
V INPU
UT
T
24V
V INPU
UT
T
+
—
+
—
(TOP)
ON
(BOTTOM)
0: COMMS
MS
485
TB3:
RELAY
OUTPUTS
TB2:
CONTACT
INPUTS
ASS REV
(BOTTOM)
(TOP)
4
3
2
1
(BOTTOM)
8
7
6
5
(BOTTOM)
(TOP)
4
3
2
1
(BOTTOM)
8
7
6
5
J11: PHONE
PIN 3-TIP
PIN 4-RI"N"G
MODEM
TB5: COMMON ALARM
(TERMINAL BLOCKS ROTATED IN VIEW)
(BOTTOM)
Q11
R26
R402
P11
+
LS1
NO
NO
NO
N
ALARM
SENS
TOP
ENABLE
AUDIBLE
(TOP)
NO C NC NO C NC
ALL CIRCUITS;
CLASS 2
TB9: ANALOG
GROUND
+ +
——
+
—
+
—
3-4 BOTTOM
1-2 TOP
Back of LCD
Transformer Module
Controller Board
Ground wire
for LCD
On/Off switch
for Transformer
Module
Knockouts and
access slots
(top and bottom)
Power
receptacle
Introduction
3
1.6 Typical Configuration
Figure 3 shows an example of external devices connected to the Universal Monitor’s controller board.
There may be up to eight digital output, eight digital input and four analog input devices connected.
The optional Universal Monitor Expansion Board provides additional connections for eight output
and sixteen digital input devices. Remote access is available via SiteScan Web and through the
modem, which enables pager notifications and use of the Service Terminal Interface.
Figure 3 Typical Configuration
OUT1
K1
V1 V3 V5 V7 V9 V11 V13 V15
V2 V4 V6 V8 V10 V12 V14 V16
K2 K3 K4 K5 K6 K7 K8
OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
S4 S3 S2 S1
Multiflex 168AO
810-3065
DEFAULT SETTINGS FOR USE WITH UNIVERSAL MONITOR
USE COPPER (CU) CONDUCTORS ONLY.
D6
POWER INPUT
EIA485 + (to UM-)
0V
EIA485 - (to UM+)
RELAY OUTPUTS
BAR CODE
BAR CODE
LIEBERT
BATTERY
LCD
CONTRAST
VBATT
START
TB7:
24V INPUT
P23:
BATTERY
485
+—
+—
(TOP)
(BOTTOM)
TB10: COMMS
422
TB3:
RELAY
OUTPUTS
TB2:
CONTACT
INPUTS
ASS REV
ON
ON
PFM5
OFF
ON
PFM2
OFF
(BOTTOM)
(TOP)
4
3
2
1
8
7
6
5
(BOTTOM)
(TOP)
4
3
2
1
8
7
6
5
J11: PHONE
PIN 3-TIP
PIN 4-RING
MODEM
TB5: COMMON ALARM
(TERMINAL BLOCKS ROTATED IN VIEW)
(BOTTOM)
OM
OM
Q11
R
2
R4
0
P11
+
LS1
TOP
ENABLE
AUDIBLE
(TOP)
NO C NC NO C NC
ALL CIRCUITS:
CLASS 2
TB9: ANALOG
GROUND
AG
+ +
——
+—+—
3-4 BOTTOM
1-2 TOP
ON
MODEM
4
D
CAN TX
CAN RX
DS83
DS84
1
ON
ON
TP1
GND
S2
OFF
DIP
2345678
OUTPUT1
DS56
DS54
DS63
DS61
DS60
DS62
DS55
DS57
DS59
DS58
DS53
MOP
F PROG
574 TX
574 RX
485 RX
485 TX
OUTPUT2
OUTPUT3
OUTPUT4
OUTPUT5
OUTPUT6
OUTPUT7
OUTPUT8
CTRLLOCK
SENLOCK
CMN ALR
INPUT1
DS70
DS67
DS66
DS65
DS64
R334
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
C71
R
4
Digital outputs
Digital inputs
Analog inputs
Phone
line
RS232
SiteScan Web
Third-party
system
(BMS,
security
office)
LT460
LT410
UPS
Water
pump
Digital outputs
Digital inputs
Fire alarm
panel
Generator
Chiller
Exhaust
fan
Heat
rejection
unit
Expansion Board
(optional)
Universal Monitor
main board
Introduction
4
1.7 Controller Board Overview
The Universal Monitor’s controller board has connectors for eight digital inputs, four analog inputs
and eight digital outputs, as shown below. The board comes complete with light emitting diodes
(LEDs) to display the status of monitored devices, a battery pack for short-term backup, communica-
tions ports, power connections and other features necessary to monitor and protect your operation.
Table 1 Controller board components
Item Description For more information, see:
A - Power On/Off
switch
Power switch for the controller board. When switched off,
the battery pack is disabled.
2.4: Connect Power to the
Universal Monitor
B - Battery pack
Provides battery backup during a power loss to maintain
normal operation of the panel for a minimum of 10 minutes.
The analog inputs will not be functional during a power loss
(P/N 133455P1).
2.4.3: Connecting the Battery Pack
9.9.4: Connect Battery
C - EIA422 LEDs Indicates the connection status between the Universal
Monitor and SiteScan Web. 1.9: LED Indicators
D - Audible horn Provides audible notification when an alarm occurs. N/A
E - Audible horn
jumper
Jumper to disable the audible horn (factory default is
enabled). N/A
F - Common Alarm
connectors
The two common alarm connections are used to connect to
a secondary warning device such as a horn, light or
Building Management System (BMS). When an alarm is
present, the contacts close and the external warning device
is activated/notified. The common alarm contacts may be
configured to be reset with the Silence button/command.
4.0: Wiring and Connections -
Main Board
4.4: Connecting Common Alarm
Outputs
9.4: Setup System - Setup
Common Alarm
G - Digital output
status LEDs
Each output has an LED to indicate its status: ON/OFF
(energized/de-energized). 1.9: LED Indicators
H - Manual Override
Switch (outputs)
Placing the switch in the ON position will turn ON, or energize,
all eight outputs simultaneously. This switch removes all
automatic output control from the Universal Monitor.
9.11: Manual Output Ctrl
I - Digital output
connectors
Each of the eight output connections is a two-state point:
ON/OFF (energized/de-energized).
An example of a field digital output point is a motor starter.
4.0: Wiring and Connections -
Main Board
4.2.2: Connecting Digital Outputs
7.6: View Output Status
9.7: Setup System - Setup Output
J - Status LEDs Indicates the operational status of the controller board. 1.9: LED Indicators
BAR CODE
BAR CODE
LIEBERT
BATTERY
LCD
CONTRAST
VBATT
START
TB7:
24V INPUT
P23:
BATTERY
485
+—
+—
(TOP)
(BOTTOM)
TB10: COMMS
422
TB3:
RELAY
OUTPUTS
TB2:
CONTACT
INPUTS
ASS REV
ON
ON
PFM5
OFF
ON
PFM2
OFF
(BOTTOM)
(TOP)
4
3
2
1
8
7
6
5
(BOTTOM)
(TOP)
4
3
2
1
8
7
6
5
J11: PHONE
PIN 3-TIP
PIN 4-RING
MODEM
TB5: COMMON ALARM
(TERMINAL BLOCKS ROTATED IN VIEW)
(BOTTOM)
OM
OM
Q11
R
2
R4
0
P11
+
LS1
TOP
ENABLE
AUDIBLE
(TOP)
NO C NC NO C NC
ALL CIRCUITS:
CLASS 2
TB9: ANALOG
GROUND
AG
+ +
——
+—+—
3-4 BOTTOM
1-2 TOP
ON
MODEM
4
D
CAN TX
CAN RX
DS83
DS84
1
ON
ON
TP1
GND
S2
OFF
DIP
2345678
OUTPUT1
DS56
DS54
DS63
DS61
DS60
DS62
DS55
DS57
DS59
DS58
DS53
MOP
F PROG
574 TX
574 RX
485 RX
485 TX
OUTPUT2
OUTPUT3
OUTPUT4
OUTPUT5
OUTPUT6
OUTPUT7
OUTPUT8
CTRLLOCK
SENLOCK
CMN ALR
INPUT1
DS70
DS67
DS66
DS65
DS64
R334
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
C71
R
4
I - Digital output
connectors
L - Digital input
connectors
T - Phone
line
connector
R - EIA485
connector
S - Serial
interface
connector
(RS232/EIA574)
CC - Battery pack
connector
DD - 24VAC power
connector
EE - Transformer
Module
E - Audible horn
jumper
G - Digital output
status LEDs
K - Digital output
loss-of-power
jumper
H - Manual
Override Switch
(outputs)
X - Modem
J - Status LEDs
B - Battery
pack
A - Power
On/Off switch
AA - LCD connector
N - Analog
ground
connector
O - Analog
input
connectors
U - Power
receptacle
V - Power On/Off
switch
M - Digital input
status LEDs
BB - LCD contrast
adjustment
C - EIA422
LEDs
Y - Modem
status LEDs
P - 12VDC/24VDC
analog input
jumper
Q - SiteScan
Web
connector
(EIA422)
D - Audible
horn
Z - DIP switch 1
W - 24VAC
connector
F - Common
Alarm
connectors
Introduction
5
K - Digital output loss-
of-power jumper
One of eight output jumpers. Each digital output has a
jumper to set the fail-safe position of the output point when
power fails. The OFF position makes the contact Normally
Open (factory default). The ON position makes the contact
Normally Closed.
Note: The jumper position has no effect on the contact
when the Universal Monitor has power.
4.2.3: Setting the Digital Output
Jumpers
9.7.4: Configure Main Board Output
for Loss of Power (“Fail-
Safe”)
L - Digital input
connectors
Each of the eight input connections is a two-state point:
ON/OFF (energized/de-energized).
An example of a field digital input point is a leak detector.
4.0: Wiring and Connections -
Main Board
4.2.1: Connecting Digital Inputs
7.5: View Input Status
9.3: Setup System - Setup Input
M - Digital input status
LEDs
Each input has an LED to indicate its status: ON/OFF
(energized/de-energized). 1.9: LED Indicators
N - Analog ground
connector
Connection for an externally powered analog sensor that
needs a reference to ground.
4.3.2: Connecting the Analog
Ground
O - Analog input
connectors
Each of the four input connections accepts a 4/20 mA
signal.
An example of a field analog input point is a temperature
sensor.
4.0: Wiring and Connections -
Main Board
4.3: Connecting Analog Inputs
7.5: View Input Status
9.5: Setup System - Setup
Sensor
P - 12VDC/24VDC
analog input jumper
One jumper to select voltage supplied for two-wire analog
sensors. The jumper supplies all four analog input
connectors with the same voltage. Factory default is 24VDC.
4.3.1: Setting the 12VDC/24VDC
Analog Power Jumper
Q - SiteScan Web
connector (EIA422)
Connection to monitor Universal Monitor from Liebert’s
SiteScan Web graphical monitoring package.
4.0: Wiring and Connections -
Main Board
4.5: EIA422 SiteScan Web
Connector
R - EIA485 connector Connection to optional Expansion Board (purchased
separately). Connect maximum of one Expansion Board.
4.0: Wiring and Connections -
Main Board
5.3.1: Connect EIA485 Connectors
to Main Board
S - Serial interface
connector (RS232/
EIA574)
Connection for laptop or video terminal. Used for
configuration and monitoring using the Service Terminal
Interface. Requires a null modem cable for connectivity
(P/N 201258P1).
4.6.1: RS232 Connector
A.2: Connecting to the Service
Terminal Interface
T - Phone line
connector
Connection for phone line. Used for pager notifications,
service phone number, and configuration and monitoring
using the Service Terminal Interface. Requires an RJ11
connector.
4.6.2: Phone Line Connector
9.8: Setup System - Setup
Modem & Pagers
9.9.6: Setup Serv Ph Num - Enter
Phone Number
A.2: Connecting to the Service
Terminal Interface
U - Power receptacle
(Transformer Module)
115VAC power receptacle to power laptop during
configuration and diagnostics. Receptacle not available on
230VAC Transformer Module.
2.4.2: Termination and Mounting -
Large Enclosure
4.0: Wiring and Connections -
Main Board
V - Power On/Off
switch (Transformer
Module)
Power switch to turn power On/Off to both Transformer
Module 24VAC connectors and power receptacle.
2.4.2: Termination and Mounting -
Large Enclosure
4.0: Wiring and Connections -
Main Board
W - 24VAC connector
(Transformer Module)
One of the two 24VAC connectors for power (the second is
also on the right side of the Transformer Module near the
top). Each connector is rated for 40VA.
2.4.2: Termination and Mounting -
Large Enclosure
4.0: Wiring and Connections -
Main Board
X - Modem On-board modem with 9600 baud rate. 9.8: Setup System - Setup
Modem & Pagers
Y - Modem status LEDs Indicates the operational status of the modem. 1.9: LED Indicators
Z - DIP switch 1 DIP switch used for resetting password to default. 9.9.1: Change Password
AA - LCD connector Connection for the LCD on the enclosure door. N/A
BB - LCD contrast
adjustment Adjustment contrast for the LCD on the enclosure door. N/A
CC - Battery pack
connector Connection for battery pack lead. 2.4.3: Connecting the Battery Pack
DD - 24VAC power
connector Power connection for the controller. Requires 24VAC. 2.4: Connect Power to the
Universal Monitor
EE - Transformer
Module
Transformer Module used to convert 115VAC or 230VAC
to 24VAC. Available only in the large enclosure.
2.4.2: Termination and Mounting -
Large Enclosure
Table 1 Controller board components (continued)
Item Description For more information, see:
Introduction
6
1.8 Optional Expansion Board Overview
The Universal Monitor Expansion Board, purchased separately, has connectors for 16 digital inputs
and eight digital outputs, as shown below. The board has light emitting diodes (LEDs) to display the
status of monitored output devices, communications ports for connection to the Universal Monitor,
power connections and other features necessary to monitor and protect your operation.
Table 2 Expansion board components
Item Description For more information, see:
A - Digital output
connectors (8)
Each of the eight output connections is a two-state point:
ON/OFF (energized/de-energized).
An example of a field digital output point is a motor starter.
5.0: Wiring and Connections -
Optional Expansion Board
4.2.2: Connecting Digital Outputs
7.6: View Output Status
9.7: Setup System - Setup Output
B - Digital output
fuses (8)
Bussmann GMA-2 or equivalent. 250V 2A Fast Blow fuse.
CAUTION: Fuses must be replaced with equivalent fuses.
NOTE: Two (2) replacement fuses are shipped with
the Expansion Board enclosure.
N/A
C - Digital output
DIP switch
DIP switch used for setting Normally Open / Normally
Closed.
5.2.3: Setting the Digital Output DIP
Switches
9.7.3: Set Expansion Board Output by
DIP Switch
D - Digital output
status LEDs (8)
Each output has an LED to indicate its status: ON/OFF
(energized/de-energized).
1.10: LED Indicators - Optional
Expansion Board
E - Digital input
connectors (16)
Each of the 16 input connections is a two-state point: ON/
OFF (energized/de-energized).
An example of a field digital input point is a leak detector.
5.0: Wiring and Connections -
Optional Expansion Board
4.2.1: Connecting Digital Inputs
7.5: View Input Status
9.3: Setup System - Setup Input
F - General status
LED (green) Indicates the operational status of the Expansion Board. 1.10: LED Indicators - Optional
Expansion Board
G - EIA485 status
LEDs (yellow & red)
Two LEDs indicate status of the EIA485 connection:
ON/OFF (energized/de-energized).
1.10: LED Indicators - Optional
Expansion Board
H - EIA485
connector Connection to the Universal Monitor.
5.3.1: Connect EIA485 Connectors to
Main Board
9.10: Setup Exp Board - Optional
Expansion Board
I - Power status LED
(green) Indicates the power status of the Expansion Board. 1.10: LED Indicators - Optional
Expansion Board
J - 24VAC power
connector
Power connection for the Expansion Board. Requires
24VAC.
3.4: Input Power Connections -
Optional Expansion Board
OUT1
K1
V1 V3 V5 V7 V9 V11 V13 V15
V2 V4 V6 V8 V10 V12 V14 V16
K2 K3 K4 K5 K6 K7 K8
OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
S4 S3 S2 S1
Multiflex 168AO
810-3065
DEFAULT SETTINGS FOR USE WITH UNIVERSAL MONITOR
USE COPPER (CU) CONDUCTORS ONLY.
D6
POWER INPUT
EIA485 + (to UM-)
0V
EIA485 - (to UM+)
RELAY OUTPUTS
H - EIA485
connector
E - Digital input
connectors (16)
F - General
status LED
(green)
G - EIA485
status LEDs
(yellow & red)
I - Power status
LED (green)
B - Digital
output
fuses (8)
J - 24VAC
power
connector
A - Digital output
connectors (8)
C - Digital
output
DIP switch
D - Digital output
status LEDs (8)
Introduction
7
1.9 LED Indicators
The Universal Monitor’s controller board has LED indicators that show the status of inputs, outputs
and the common alarm, as well as the modem and SiteScan Web connections.
Table 3 LED indicators summary
LED Type LED Color Description
EIA422
LEDs
422 TX Green Universal Monitor is transmitting information over the EIA422 port
422 RX Green Universal Monitor is receiving information over the EIA422 port
Modem
LEDs
TX Green Universal Monitor is transmitting information via the modem
RX Green Universal Monitor is receiving information via the modem
DTR Green Indicates data terminal is ready (DTR)—lights up when modem is dialing
DCD Green Indicates data carrier is detected (DCD)—lights up when modem has connection
Output
LEDs
OUTPUT1 Green Indicates output is ON or energized
OUTPUT2 Green Indicates output is ON or energized
OUTPUT3 Green Indicates output is ON or energized
OUTPUT4 Green Indicates output is ON or energized
OUTPUT5 Green Indicates output is ON or energized
OUTPUT6 Green Indicates output is ON or energized
OUTPUT7 Green Indicates output is ON or energized
OUTPUT8 Green Indicates output is ON or energized
CTRLLOCK N/A Not used
SENLOCK N/A Not used
CMN ALR Green Indicates output is ON or energized
Status
LEDs
MOP Green Indicates the microprocessor is operating properly (MOP)—must be on before
Universal Monitor will function
FPROG Green Indicates firmware is being upgraded—lights up during upgrade process
574 TX or 232 TX Green Universal Monitor is transmitting information via the RS232 port
574 RX or 232 RX Green Universal Monitor is receiving information via the RS232 port
485 RX Green Universal Monitor is receiving information over the EIA485 port from the Expansion
Board
485 TX Green Universal Monitor is transmitting information over the EIA485 port to the Expansion
Board
Input
LEDs
INPUT1 Red Indicates input is ON or energized
INPUT2 Red Indicates input is ON or energized
INPUT3 Red Indicates input is ON or energized
INPUT4 Red Indicates input is ON or energized
INPUT5 Red Indicates input is ON or energized
INPUT6 Red Indicates input is ON or energized
INPUT7 Red Indicates input is ON or energized
INPUT8 Red Indicates input is ON or energized
OUTPUT1
DS56
DS54
DS63
DS61
DS60
DS62
DS55
DS57
DS59
DS58
DS53
DS52 MOP
F PROG
574 TX
574 RX
485 RX
485 TX
DS51
DS48
DS47
DS78
DS79
OUTPUT2
OUTPUT3
OUTPUT4
OUTPUT5
OUTPUT6
OUTPUT7
OUTPUT8
CTRLLOCK
SENLOCK
CMN ALR
INPUT1
DS69
DS71
DS72
DS70
DS67
DS66
DS65
DS64
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
DS50
DS49
EIA422 SiteScan
Web LEDs
BAR CODE
BAR CODE
LIEBERT
BATTERY
LCD
CONTRAST
VBATT
START
TB7:
24V INPUT
P23:
BATTERY
485
+—
+—
(TOP)
(BOTTOM)
TB10: COMMS
422
TB3:
RELAY
OUTPUTS
TB2:
CONTACT
INPUTS
ASS REV
ON
ON
PFM5
OFF
ON
PFM2
OFF
(BOTTOM)
(TOP)
4
3
2
1
8
7
6
5
(BOTTOM)
(TOP)
4
3
2
1
8
7
6
5
J11: PHONE
PIN 3-TIP
PIN 4-RING
MODEM
TB5: COMMON ALARM
(TERMINAL BLOCKS ROTATED IN VIEW)
(BOTTOM)
OM
OM
Q11
R
2
R4
0
P11
+
LS1
TOP
ENABLE
AUDIBLE
(TOP)
NO C NC NO C NC
ALL CIRCUITS:
CLASS 2
TB9: ANALOG
GROUND
AG
+ +
——
+—+—
3-4 BOTTOM
1-2 TOP
ON
MODEM
4
D
CAN TX
CAN RX
DS83
DS84
1
ON
ON
TP1
GND
S2
OFF
DIP
2345678
OUTPUT1
DS56
DS54
DS63
DS61
DS60
DS62
DS55
DS57
DS59
DS58
DS53
MOP
F PROG
574 TX
574 RX
485 RX
485 TX
OUTPUT2
OUTPUT3
OUTPUT4
OUTPUT5
OUTPUT6
OUTPUT7
OUTPUT8
CTRLLOCK
SENLOCK
CMN ALR
INPUT1
DS70
DS67
DS66
DS65
DS64
R334
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
INPUT8
C71
R
4
Output LEDs
Status LEDs
Input LEDs
MODEM
DS77 TX
DS76 RX
DS74 DTR
DS75 DCD
Modem LEDs
Introduction
8
1.10 LED Indicators - Optional Expansion Board
The optional Expansion Board, purchased separately, has LED indicators that show the status of
inputs and outputs.
Table 4 LED indicators summary
LED Type LED Color Description
Power status
LED
24VAC
Power (D6) Green 24VAC power is being supplied to Expansion Board
EIA485 status
LEDs
485 RX (D4) Yellow Expansion Board is receiving information over the EIA485 port from the
Universal Monitor
485 TX (D5) Red Expansion Board is transmitting information over the EIA485 port to the
Universal Monitor
General status
LED
General
Status (D3) Green Blinks green once per second to indicate the board is powered and
operational. If the light is off, the board has likely lost power.
Digital output
status
LEDs
OUT1 Red Indicates output is ON or energized
OUT2 Red Indicates output is ON or energized
OUT3 Red Indicates output is ON or energized
OUT4 Red Indicates output is ON or energized
OUT5 Red Indicates output is ON or energized
OUT6 Red Indicates output is ON or energized
OUT7 Red Indicates output is ON or energized
OUT8 Red Indicates output is ON or energized
D4
D5
Rx
Tx
D6
OUT1
K1
V1 V3 V5 V7 V9 V11 V13 V15
V2 V4 V6 V8 V10 V12 V14 V16
K2 K3 K4 K5 K6 K7 K8
OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
S4 S3 S2 S1
Multiflex 168AO
810-3065
DEFAULT SET TINGS FOR USE WITH UNIVERSAL MONITOR
USE COPPER (CU) CONDUCTORS ONLY.
D6
POWER INPUT
EIA485 + (to UM-)
0V
EIA485 - (to UM+)
RELAY OUTPUTS
K4K3K2K1 K5 K6 K7 K8
OUT3OUT1 OUT2 OUT4 OUT5 OUT6 OUT7 OUT8
D3
Gen.
Status
General status LED
(D3 - green)
Digital output status LEDs (8)
Power status LED
(D6 - green)
EIA485 status LEDs
(D4 - yellow,
D5 - red)
Introduction
9
1.11 Typical Sequence
Figure 4 shows a typical sequence of how the Universal Monitor functions after detecting a change in
a monitored unit or area. Many responses depend on configuration settings. This example shows what
happens when an analog sensor input reaches a high setpoint—assuming the input is defined as
alarmable and is set up to trigger a response in an output—and when the condition returns to normal.
Figure 4 Example of typical sequence: Analog input reaches high setpoint
SENSOR_2 79.0 DEG
RETURN TO NORMAL
29-AUG-02 09:42:11
Entry in Alarm Log
Shows reading (79.0 DEG) &
condition (RETURN TO NORMAL)
SENSOR_2 80.0 DEG
HIGH SETPOINT ALARM
29-AUG-02 09:29:10
Entry in Alarm Log
Shows reading (80.0 DEG) &
condition (HIGH SETPOINT ALARM)
The alarm is cleared
(automatically if Unlatched; must be
cleared manually if Latched)
UNIVERSAL MONITOR
05-SEP-02 14:04:13
V5.100.0
PRESS =STATUS/SETUP
ESC
ESC
The LCD stops flashing
When the alarm is cleared,
the fan shuts down
RETURN TO NORMAL
The temperature in the monitored
analog input returns to a normal
range (below the high setpoint).
The horn sounds (audible horn on
the controller board—silence horn by
pressing any key on the LCD keypad)
The LCD flashes
(except during setup)
Pager numbers are dialed
(up to four configured pagers)
Service number is dialed
(if configured)
A fan is turned on
(if the fan is connected to an output
set up to respond to this input)
ALARM CONDITION DETECTED
The temperature in a monitored
analog input reaches its high setpoint.
RESPONSES TO AN ALARM RETURN-TO-NORMAL SEQUENCE
UNIVERSAL MONITOR
05-SEP-02 14:04:13
V5.100.0
PRESS =STATUS/SETUP
ESC
ESC
OUTPUT08 OFF
CONTACT CLOSED
05-MAY-02 09:42:12
OUTPUT08 ON
CONTACT OPEN
29-AUG-02 09:29:12
SENSOR_2 80.0 DEG
HIGH SETPOINT ALARM
Entry in Event Log
Fan output on
Entry in Event Log
Fan output off
Entry in Active Alarm Log
Pager numbers & service
number are dialed
Return-to-normal message sent
The horn stops sounding
(if user hasn’t silenced it)
Installation - Main Board
10
2.0 INSTALLATION - MAIN BOARD
This section provides instructions for installing, mounting and connecting power to the Universal
Monitor. For information on the optional Expansion Board, see 3.0 - Installation - Optional Expan-
sion Board.
2.1 Installation Considerations
The Universal Monitor must be installed indoors and may be mounted on the surface of a wall or
flush-mounted, depending on the user’s application, the location of equipment and sensors to be mon-
itored and the type of wall the unit will be mounted on.
The Universal Monitor should be mounted where it can be easily accessed. On-site personnel would
access the unit through the LCD on its front cover, service terminal connected to the RS232 port or
through SiteScan. For off-site monitoring, the Universal Monitor should be placed near communica-
tions means such as a telephone line connection that would permit remote access.
In addition to the communications connections, the site also must have electrical service and must
permit connecting the unit’s eight digital inputs, eight digital outputs and four analog inputs.
The wall material must be capable of supporting the weight of the Universal Monitor: see 10.0 -
Specifications.
2.1.1 Unpacking and Preliminary Inspection
• Before unpacking the Universal Monitor, inspect the shipping carton for damage or signs of
mishandling, such as gashes or holes in the carton or severely flattened corners.
• Open the shipping crates carefully. Use care to avoid puncturing the container with sharp objects
that might damage the contents.
• Inspect the Universal Monitor and all included components for damage.
• If any damage from shipping or mishandling is observed, immediately file a damage claim with
the shipping agency and forward a copy to:
Liebert Corporation
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Packing Contents
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Table 5 Packing manifest - Universal Monitor main board
Standard Components
• Universal Monitor - large or small enclosure
• User Manual
• Keys (2) to panel door lock
• Backup Battery - installed in unit (not connected or charged)
• RS232 Configuration Cable
Installation - Main Board
11
2.2 Surface-Mounting the Universal Monitor
After determining where to place the unit, check to ensure that you have all the hardware required to
install the panel on the surface of a wall. Obtain the needed tools and material.
Required tools
• Electric drill (if surface is too hard to drive screws without pilot holes)
• Screwdriver
• Marker to denote layout of holes
• Four screws, each #10
2.2.1 Mounting the Panel
1. Mark the wall for mounting holes, using the back of the unit as a template (see Figure 5).
2. Drill holes, if required, to install the four #10 screws that will secure the Universal Monitor to the
wall. Clean up the debris.
3. If the wall material is not strong enough to hold the screws securely, use wall anchors.
4. Install the top two screws—the screw heads must be small enough to slip through the larger,
bottom portion of the pear-shaped mounting slot in the Universal Monitor (see inset in Figure 5).
The screws must also be large enough to extend over the edges of the top of the mounting slot.
5. Hang the Universal Monitor on the screws, letting the panel slip down until the screws are in the
smaller, upper portion of the slot.
6. Tighten the screws until they are snug.
7. Insert the remaining two screws in the bottom holes on the back of the panel and tighten.
Figure 5 Mounting Dimensions
NOTE
Removing the conduit knockouts before mounting the Universal Monitor on the wall will ease
installation and prevent strain on the mounting hardware and wall. It is imperative to remove
the knockouts if the unit is to be flush-mounted.
!CAUTION
Check building plans and other relevant documents to determine whether mounting the
Universal Monitor at the selected location might cause cutting or otherwise damaging
electrical or communication wiring or pipes.
SMALL ENCLOSURE
0.213"
(5.4mm)
Mounting Slot
0.375"
(9.6mm)
Universal Monitor
back plate
12.5"
(317.5mm)
0.213" (5.4mm)
Bottom hole diameter
10"
(254mm)
LARGE ENCLOSURE
0.213"
(5.4mm)
Mounting Slot
0.375"
(9.6mm)
Universal Monitor
back plate
12"
(304.8mm)
0.213" (5.4mm)
Bottom hole diameter
16"
(406.4mm)
Installation - Main Board
12
2.3 Flush-Mounting the Universal Monitor
The Universal Monitor may be flush-mounted according to company practices—either with screws
through the sides of the panel into wall supports or with hanging hardware that attaches to the back
of the panel. After determining how and where to place the unit, check to ensure that you have all the
hardware required to install the panel in the wall. Obtain the needed tools.
Required tools
•Saw
• Electric drill
• Screwdriver
• Marker to denote layout of the hole to accommodate the Universal Monitor
• Trim ring and associated hardware
• Mounting hardware
2.3.1 Mounting the Panel
1. Mark the wall for the cutout to accommodate the panel, using the back of the unit as a template.
2. Drill a pilot hole for the saw blade, if required.
3. Use the saw to cut out the marked section of the wall (if not new construction).
4. Rest the Universal Monitor in the wall and mark where mounting screws will be inserted into the
wall studs or other support member.
5. Remove the panel and drill the holes for the mounting screws or wall anchors. Clean up the
debris.
6. Reverse the slide direction of the rectangular access doors on the top and bottom of the Universal
Monitor. Leaving the doors as shipped from the factory prevents them from being opened when
the panel is flush mounted in a wall.
7. Attach any field-supplied mounting hardware.
8. Reinsert the assembly into the wall.
9. Insert and tighten the screws or wall anchors.
NOTE
Removing the conduit knockouts before mounting the Universal Monitor on the wall will ease
installation and prevent strain on the mounting hardware and wall. It is imperative to remove
the knockouts if the unit is to be flush-mounted.
The rectangular access doors on the top and bottom of the Universal Monitor must be reversed
so they slide the opposite direction. Leaving the doors as shipped from the factory prevents
them from being opened when the panel is flush mounted in a wall.
!CAUTION
Check building plans and other relevant documents to determine whether mounting the
Universal Monitor at the selected location might cause cutting or otherwise damaging
electrical or communication wiring or pipes.
Installation - Main Board
13
2.4 Connect Power to the Universal Monitor
The Universal Monitor requires 24VAC for proper operation. Liebert recommends using the optional
Transformer Module manufactured by Liebert or another UL-approved Class 2 power unit to obtain
proper voltage. If the power unit is not a Class 2 circuit, it must be protected with an IEC 5 x 20mm
time lag 2A fuse. For information, consult your local dealer, Liebert representative or the Liebert
Worldwide Support Group.
2.4.1 Input Power Connections - Small Enclosure
To connect electrical power:
1. Run conduit and electrical wiring from building to the Universal Monitor.
2. Use copper wires only; proper wiring to use for 24VAC power is 18-22 AWG stranded and shielded
(18 AWG is recommended—see Table 7). Strip wires 1/2".
Figure 6 Electrical connections to panel
3. Secure the incoming electrical service wires to the Universal Monitor’s 24VAC input by sliding
the wires into TB7, the 24VAC input terminal block. There is no polarity requirement when
connecting to TB7. The ground wire must be connected to the earth ground terminal located on
the side of the panel (see Figure 6).
!WARNING
Check that power is removed from wires prior to installation.
!CAUTION
The Universal Monitor is designed for use on properly grounded (earthed) 24VAC power,
50Hz or 60Hz. The ground wire for the power lead must be wired to the earth ground terminal
(stud located next to the 24VAC terminal block).
This equipment is intended to be installed by a qualified and certified electrician who must
review and approve customer supplied wiring and circuit breakers, verify correct input and
grounded (earthed) connections to ensure compliance with technical standards and national
and local electrical codes.
!WARNING
Be sure that the Power On/Off switch is set to OFF before installing any wiring to this unit.
The switch is in the top left corner of the unit, just below the battery pack.
24VAC input connector
24VAC wiring
(red & white)
Power On/Off switch
External wiring
through knockout
Earth ground
terminal
Ground wire
(black)
Installation - Main Board
14
2.4.2 Termination and Mounting - Large Enclosure
Input Power Connections
To connect electrical power to the Transformer Module:
1. Install electrical wiring from utility power to the Transformer Module.
2. Use copper wires only; proper wiring to use for power is 14/2 AWG copper wire with ground.
3. For the TM230 only: strip wires 3/8" (9.6mm).
Note: For the TM115, wires are pre-stripped 0.4" (10.2mm) at the factory.
4. Connect the wiring as follows:
5. Secure the incoming electrical service wires to the TM115 input wires with wire nuts as shown in
Figure 7 or to the TM230 connectors as shown in Figure 8.
24 VAC Output Power Connections
To connect to the 24VAC outputs:
1. Install electrical wiring from device requiring 24VAC power to the Transformer Module.
2. Use copper wire only; proper wiring to use for power is 18, 20 or 22 AWG copper wire. Strip
wire 1/4".
3. There are two 24 VAC output connectors (TB1 and TB2). Terminate wires to the connector as
shown in Figures 7 and 8. TB1 and TB2 are NOT polarity sensitive.
4. Secure the wires to the connector.
!CAUTION
The 115VAC/230VAC Transformer Module must be connected to a branch circuit with 15A
branch circuit protection.
This equipment is intended to be installed by a qualified and certified electrician who must
review and approve customer supplied wiring and circuit breakers, verify correct input and
grounded connections to ensure compliance with the technical standards and national and
local electrical codes.
The Transformer Module shall be used only as indicated by the manufacturer.
!WARNING
Be sure that the Power On/Off switch is set to OFF before installing any wiring to this unit.
The switch is at the bottom of the unit.
TM115 TM230 Connection Type
White wire Neutral (L2) Neutral
Black wire Line (L1) Power (Line)
Green wire Ground lead Ground
Figure 7 Power wiring to TM115 Figure 8 Power wiring to TM230
Knockout for
external wiring
Wire nuts
connecting
electrical
wiring
TM115
24VAC output
(TB1)
Ground
TM230
Line (L1)
Neutral (L2)
Knockout for
external wiring
24VAC output
(TB1)
Ground
Installation - Main Board
15
Troubleshooting - Transformer Module
A common problem and possible solution are shown in the table below. For further information or if
you have other problems with the unit, consult your local dealer, Liebert representative or the Liebert
Worldwide Support Group.
2.4.3 Connecting the Battery Pack
After connecting AC power to the Universal
Monitor, you may connect the panel’s backup
battery (factory-supplied) to the jumpers so it
will begin charging when electrical power to
the Universal Monitor is switched on.
To connect the battery pack, insert the battery
leads into the jumpers as shown at right. (To
disconnect the battery pack, remove the bat-
tery leads from the jumpers.)
Obtaining a Replacement Battery Pack
To obtain a replacement battery pack, contact
your local dealer or Liebert representative.
The Liebert part number is 133455P1.
Problem Possible Solution Replacement Fuse Part Numbers
24VAC power
not available
from TB1 or TB2
Check fuse for respective
output (TB1 or TB2).
• LITTLEFUSE 218002
or
• BUSSMANN GDC-2A
NOTE
If the battery is not hooked up before
the Universal Monitor is switched on,
it will trigger an alarm.
!WARNING
To prevent the risk of fire or explosion,
replace only with 7.2 V rechargeable
NiCad battery pack.
!CAUTION
Dispose of the battery properly by
sending it back to Liebert Corporation
or an approved battery recycling
facility.
Battery pack connector
Battery pack
Installation - Optional Expansion Board
16
3.0 INSTALLATION - OPTIONAL EXPANSION BOARD
This section provides instructions for installing, mounting and connecting power to the optional Expan-
sion Board. The Expansion Board enclosure is identical to the Universal Monitor’s small enclosure.
3.1 Installation Considerations
The optional Expansion Board must be installed indoors and may be mounted on the surface of a wall
or flush-mounted, depending on the user’s application, the location of equipment and sensors to be
monitored and the type of wall the unit will be mounted on.
The Expansion Board may be placed up to 3000 ft. (914m) from the Universal Monitor and should be
mounted where it can be easily accessed. The site must have electrical service and allow for connect-
ing 16 digital inputs and eight digital outputs.
The wall material must be capable of supporting the weight of the Expansion Board: see 10.2 -
Optional Expansion Board Specifications.
3.1.1 Unpacking and Preliminary Inspection
• Before unpacking the optional Expansion Board, inspect the shipping carton for damage or signs
of mishandling, such as gashes or holes in the carton or severely flattened corners.
• Open the shipping crates carefully. Use care to avoid puncturing the container with sharp objects
that might damage the contents.
• Inspect the Expansion Board and all included components for damage.
• If any damage from shipping or mishandling is observed, immediately file a damage claim with
the shipping agency and forward a copy to:
Liebert Corporation
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Packing Contents
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Table 6 Packing manifest - optional Expansion Board
Standard Components
• Expansion Board - small enclosure
• User Manual
• Keys (2) to panel door lock
• Two (2) spare fuses for output relays
Installation - Optional Expansion Board
17
3.2 Surface-Mounting the Optional Expansion Board
After determining where to place the optional Expansion Board, check to ensure that you have all the
hardware required to install the panel on the surface of a wall. Obtain the needed tools and material.
Required tools
• Electric drill (if surface is too hard to drive screws without pilot holes)
• Screwdriver
• Marker to denote layout of holes
• Four screws, each #10
3.2.1 Mounting the Panel
1. Mark the wall for mounting holes, using the back of the unit as a template (see Figure 5).
2. Drill holes, if required, to install the four #10 screws that will secure the optional Expansion
Board to the wall. Clean up the debris.
3. If the wall material is not strong enough to hold the screws securely, use wall anchors.
4. Install the top two screws—the screw heads must be small enough to slip through the larger,
bottom portion of the pear-shaped mounting slot in the Expansion Board (see inset in Figure 5).
The screws must also be large enough to extend over the edges of the top of the mounting slot.
5. Hang the Expansion Board on the screws, letting the panel slip down until the screws are in the
smaller, upper portion of the slot.
6. Tighten the screws until they are snug.
7. Insert the remaining two screws in the bottom holes on the back of the panel and tighten.
Figure 9 Mounting Dimensions - optional Expansion Board
NOTE
Removing the conduit knockouts before mounting the optional Expansion Board on the wall
will ease installation and prevent strain on the mounting hardware and wall. It is imperative
to remove the knockouts if the unit is to be flush-mounted.
!CAUTION
Check building plans and other relevant documents to determine whether mounting the
optional Expansion Board at the selected location might cause cutting or otherwise damaging
electrical or communication wiring or pipes.
SMALL ENCLOSURE
0.213"
(5.4mm)
Mounting Slot
0.375"
(9.6mm)
Expansion Board
back plate
12.5"
(317.5mm)
0.213" (5.4mm)
Bottom hole diameter
10"
(254mm)
Installation - Optional Expansion Board
18
3.3 Flush-Mounting the Optional Expansion Board
The optional Expansion Board may be flush-mounted according to company practices—either with
screws through the sides of the panel into wall supports or with hanging hardware that attaches to
the back of the panel. After determining how and where to place the unit, check to ensure that you
have all the hardware required to install the panel in the wall. Obtain the needed tools.
Required tools
•Saw
• Electric drill
• Screwdriver
• Marker to denote layout of the hole to accommodate the optional Expansion Board
• Trim ring and associated hardware
• Mounting hardware
3.3.1 Mounting the Panel
1. Mark the wall for the cutout to accommodate the panel, using the back of the unit as a template.
2. Drill a pilot hole for the saw blade, if required.
3. Use the saw to cut out the marked section of the wall (if not new construction).
4. Rest the optional Expansion Board in the wall and mark where mounting screws will be inserted
into the wall studs or other support member.
5. Remove the panel and drill the holes for the mounting screws or wall anchors. Clean up the
debris.
6. Reverse the slide direction of the rectangular access doors on the top and bottom of the Expansion
Board. Leaving the doors as shipped from the factory prevents them from being opened when the
panel is flush mounted in a wall.
7. Attach any field-supplied mounting hardware.
8. Reinsert the assembly into the wall.
9. Insert and tighten the screws or wall anchors.
NOTE
Removing the conduit knockouts before mounting the optional Expansion Board on the wall
will ease installation and prevent strain on the mounting hardware and wall. It is imperative
to remove the knockouts if the unit is to be flush-mounted.
The rectangular access doors on the top and bottom of the Expansion Board must be reversed
so they slide the opposite direction. Leaving the doors as shipped from the factory prevents
them from being opened when the panel is flush mounted in a wall.
!CAUTION
Check building plans and other relevant documents to determine whether mounting the
optional Expansion Board at the selected location might cause cutting or otherwise damaging
electrical or communication wiring or pipes.
Installation - Optional Expansion Board
19
3.4 Input Power Connections - Optional Expansion Board
The optional Expansion Board requires 24VAC for proper operation. Liebert recommends using the
optional Transformer Module manufactured by Liebert or another UL-approved Class 2 power unit to
obtain proper voltage. If the power unit is not a Class 2 circuit, it must be protected with an IEC
5 x 20mm time lag 2A fuse. For information, consult your local dealer, Liebert representative or the
Liebert Worldwide Support Group.
To connect electrical power:
1. Run 24VAC electrical power from the TB2 (or TB1) connector of the Transformer Module, as
shown in Figure 10, or another 24V source to the Expansion Board in accordance with local
electrical codes.
2. Use copper wires only; proper wiring to use for power is 18-22 AWG stranded and shielded
(18 AWG is recommended—see Table 9). Strip wires 1/2".
Figure 10 Electrical connections to panel
3. Secure the incoming electrical service wires to the Expansion Board’s 24VAC input by sliding the
wires into AC1 and AC2, the 24VAC input connectors, as shown in Figure 10. There is no
polarity requirement when connecting to these connectors.
NOTE: The ground wire connection to the 0V connector is pre-wired at the factory.
!CAUTION
The Expansion Board is designed for use on properly grounded (earthed) 24VAC Class 2
power, 50Hz or 60Hz. The ground wire for the power lead must be wired to the earth ground
terminal (stud located next to the 24VAC terminal block). This equipment is intended to be
installed by a qualified and certified electrician who must review and approve customer-
supplied wiring and circuit breakers, verify correct input and grounded (earthed) connections
to ensure compliance with technical standards and national and local electrical codes.
!WARNING
“RISK OF ELECTRIC SHOCK” - More than one disconnect switch may be required to
de-energize the equipment before servicing.
!WARNING
Hazardous voltage may be present.
S4
EIA485 + (to UM-)
0V
EIA485 - (to UM+)
POWER INPUT
TRANSFORMER MODULE
(TM115 shown)
24VAC output (TB2 shown;
use either TB1 or TB2)
24VAC wiring
(red & white)
24VAC input
connectors
(AC1 & AC2)
Ground wire
(pre-wired)
OPTIONAL EXPANSION BOARD
Ground wire
connector
(0V)
Wiring and Connections - Main Board
20
4.0 WIRING AND CONNECTIONS - MAIN BOARD
4.1 Wiring Specifications
Input and output connections to the Universal Monitor may be made in any order—it is not neces-
sary, for example, to make all input connections before making any output connections. Use copper
conductors only for all wiring.
!CAUTION
Switch OFF electric power to the Universal Monitor before installing any wiring to the unit or
changing input or output connections. The Power On/Off switch is in the top left corner of the
unit, just below the battery pack.
Table 7 Wiring specifications - main board
Connection Supported Wire Type Maximum Wire Length Rating
Digital
Input
18-22 AWG Stranded & Unshielded
18 AWG* (recommended)
Non Plenum - Belden 9740
Plenum - Belden 89740
750 ft. (225m)
Dry Contact
(24VDC,
10 mA)
Digital
Output
18-22 AWG Stranded & Unshielded
18 AWG* (recommended)
Non Plenum - Belden 9740
Plenum - Belden 89740
18 AWG*
(recommended) 20 AWG 22 AWG
24VAC
@3A
@3A 50 ft. (15m)
@2A 100 ft. (30m)
@1A 200 ft. (60m)
@3A 40 ft. (12m)
@2A 60 ft. (18m)
@1A 100 ft. (30m)
@3A 25 ft. (7m)
@2A 35 ft. (10m)
@1A 75 ft. (23m)
Analog Input
2-Wire
Transducer
18-22 AWG Stranded & Unshielded
18 AWG* (recommended)
Non Plenum - Belden 9740
Plenum - Belden 89740
750 ft. (225m)
4-20 mA Signal
Input Selectable
Power Source
(12/24VDC)
Analog Input
4-Wire
Transducer
18-22 AWG Stranded & Unshielded
18 AWG* (recommended)
Non Plenum - Belden 8489
Plenum - Belden 88489
750 ft. (225m)
4-20 mA Signal
Input Selectable
Power Source
(12/24VDC)
Common
Alarm
Output
18-22 AWG Stranded & Unshielded
18 AWG* (recommended)
Non Plenum - Belden 9740
Plenum - Belden 89740
18 AWG*
(recommended) 20 AWG 22 AWG
24VAC
@3A
@3A 50 ft. (15m)
@2A 100 ft. (30m)
@1A 200 ft. (60m)
@3A 40 ft. (12m)
@2A 60 ft. (18m)
@1A 100 ft. (30m)
@3A 25 ft. (7m)
@2A 35 ft. (10m)
@1A 75 ft. (23m)
Communication
RS232 Null Modem Cable 50 ft. (15m) N/A
Communication
EIA422
SiteScan
18-22 AWG Stranded & Shielded
22 AWG* (recommended)
Non Plenum - Belden 9461
Plenum - Belden 88761
1000 ft. (300m) N/A
Communication
EIA485
18-22 AWG Stranded & Shielded
22 AWG* (recommended)
Non Plenum - Belden 9461
Plenum - Belden 88761
3000 ft. (900m) N/A
Phone/Modem
Line
4 Wire (Pins 3 & 4)
RJ11 Connector N/A N/A
24VAC Power
Connection
(TB7)
18-22 AWG Stranded & Shielded
18 AWG* (recommended)
Non Plenum - Belden 8770
Plenum - Belden 88770
150 ft. (45m) 24VAC
@1.3A
Power Connections (Transformer Module)
115VAC 14 AWG Stranded & Unshielded
Non Plenum - Belden 5101UE 150 ft. (45m) 115VAC
@4A
230VAC 14 AWG Stranded & Unshielded
Non Plenum - Belden 5101UE 150 ft. (45m) 230VAC
@0.5A
* Recommended
Wiring and Connections - Main Board
21
4.2 Connecting Digital Inputs and Digital Outputs
The digital inputs and digital outputs are found on the lower right side of the Universal Monitor’s
printed wiring assembly board. There are two terminal blocks for the inputs—one green, the other
black. There are two terminal blocks for the outputs—one green, the other black.
To determine the proper wire size, see Table 7 - Wiring specifications - main board.
4.2.1 Connecting Digital Inputs
To connect an input:
1. Turn OFF electrical power to the Universal
Monitor.
2. If necessary, remove a conduit knockout to
permit wire entry into the Universal
Monitor enclosure.
3. Bring the wire(s) into the Universal Monitor
enclosure through a conduit knockout or
access slot.
4. Loosen the appropriate screw and slip the
stripped end of the wire into the terminal
block.
5. Tighten the screw until it holds the wire
snugly.
4.2.2 Connecting Digital Outputs
To connect an output:
1. Turn OFF electrical power to the Universal
Monitor.
2. If necessary, remove a conduit knockout to
permit wire entry into the Universal
Monitor enclosure.
3. Bring the wire(s) into the Universal Monitor enclosure through a conduit knockout or access slot.
4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.
5. Tighten the screw until it holds the wire snugly.
NOTE
Each terminal block is a removable, two-part assembly to permit easier connection of more
than one input at a time. If making multiple connections, grasp the upper portion of a block
and pull firmly to the right until the assembly pulls apart.
After making the connections, push the removed piece back into the portion attached to the
printed wiring assembly until the terminal block pieces lock together.
!CAUTION
To reduce the risk of fire or electric shock, do not interconnect the outputs of
different Class 2 circuits.
TB2:
CONTACT
INPUTS
TB3:
RELAY
OUTPUTS
ASS REV
ON
PFM5
OFF ON
PFM2
OFF
(BOTTOM)
(TOP)
4
3
2
1
8
7
6
5
(BOTTOM)
(TOP)
4
3
2
1
8
7
6
5
OUTPUT TERMINAL BLOCKS -
Note numbering of outputs
begins at the bottom and
proceeds up; numbering
keys are shown at right
INPUT TERMINAL BLOCKS -
Note numbering of inputs
begins at the bottom and
proceeds up; numbering
keys are shown at right
Numbering keys
Wiring and Connections - Main Board
22
4.2.3 Setting the Digital Output Jumpers
Each digital output has an associated jumper to define its operation when power is interrupted and
there is no battery backup to the board. This puts the Universal Monitor in a fail-safe mode and
ensures proper functioning when the board has no power or battery backup.
The Universal Monitor comes from the factory with
all digital output jumpers in the OFF position (nor-
mally open). The jumper setting for each digital
output can be changed to ON (normally closed).
The settings are shown in Table 8.
To change the output jumper setting:
1. Find the respective black output jumper on the
circuit board, as shown above.
2. Decide whether your configuration requires
the jumper to be OFF or ON.
3. Set the jumper as needed:
• Set the jumper to OFF by placing the black
jumper on the middle and top pins.
• Set the jumper to ON by placing the black
jumper on the middle and bottom pins.
4.3 Connecting Analog Inputs
The analog input connector blocks are at the bottom
center of the Universal Monitor printed circuit board.
The blocks are two-part assemblies to permit easier
connections. To determine the proper wire size, see
Table 7 - Wiring specifications - main board.
To connect an input:
1. Turn OFF electrical power to the Universal
Monitor.
2. If necessary, remove a conduit knockout to permit
wire entry into the Universal Monitor enclosure.
3. Bring the wire(s) into the Universal Monitor
enclosure through a conduit knockout or access slot.
4. Loosen the appropriate screw and slip the stripped
end of the wire into the terminal block.
5. Tighten the screw until it holds the wire snugly.
Table 8 Digital output jumper settings
Setting
Output status
(power loss & no battery backup)
OFF Normally open
ON Normally closed
TB3:
RELAY
OUTPUTS
REV
ON
PFM5
OFF ON
PFM2
OFF
(BOTTOM)
(TOP)
4
3
2
1
8
7
6
5
(BOTTOM)
(TOP)
4
3
2
8
7
6
Digital output jumpers
485
+—
+—
(TOP)
(BOTTOM)
0
: COMMS
422 TB9: ANALOG
GROUND
AG
+ +
——
+—+—
3-4 BOTTOM
1-2 TOP
Analog inputs Analog ground
Wiring and Connections - Main Board
23
4.3.1 Setting the 12VDC/24VDC Analog Power Jumper
The analog power jumper sets the common voltage that is applied to all of the analog input connec-
tions. The jumper permits the user to modify the voltage supplied to the sensors, according to the
power requirements.
The factory default position is 24VDC; it may be changed to 12VDC.
To change the analog power jumper setting:
1. Find the black analog jumper on the circuit board, as shown at
right. The jumper is at the bottom of the board near the middle
(see 1.7 - Controller Board Overview).
2. Decide whether your configuration requires the jumper to be
24VDC or 12VDC.
3. Set the jumper as needed:
• Set the jumper to the 24VDC position by placing the black
jumper on the middle and right pins.
• Set the jumper to the 12VDC position by placing the black
jumper on the middle and left pins.
4.3.2 Connecting the Analog Ground
The Universal Monitor features an analog ground
connection for four-wire sensors that have an
external power source. Such a four-wire sensor
requires a reference to ground because they get
power from an external power source.
A two-wire transducer, which does not have an
external power source, does not need to be con-
nected to the analog ground.
The analog ground connector has two terminals,
each of which can accommodate two wires. This is
adequate to connect four sensors that require a
reference to ground because they get power from
an external power source.
Connect the analog ground to an external four-
wire sensor as shown in the illustration at right.
485
+
—
+
—
(TOP)
(BOTTOM)
C
OMMS
422 TB9: ANAL
O
GROUND
AG
+ +
——
+
—
+
—
3-4 BOTTOM
1-2 TOP
Analog power jumper
+
+
+
—
—
+
(TOP)
(BOTTOM)
TB10: COMMS
4/20mA
Output
24V Input
TB9: ANALOG
GROUND
3-4 BOTTOM
1-2 TOP
Analog
ground
Analog
input
Four-wire
transducer
Sensor
with
external
power
24V from
external
power
source
Wiring and Connections - Main Board
24
4.4 Connecting Common Alarm Outputs
The common alarm relay, found in the top right corner of the Uni-
versal Monitor, permits the user to connect auxiliary notification
equipment, such as lights, horns and sirens, to the Universal
Monitor. To determine the proper wire size, see Table 7 - Wiring
specifications - main board.
There are two connectors for the common alarm output. However,
the connectors are not individual relay outputs. The connectors
should be treated as a double-pole, double-throw (DPDT) relay.
The common alarm relay is energized whenever an alarm occurs.
To connect an output:
1. Turn OFF electrical power to the Universal Monitor.
2. If necessary, remove a conduit knockout to permit wire entry into the Universal Monitor
enclosure.
3. Bring the wire(s) into the Universal Monitor enclosure through a conduit knockout or access slot.
4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.
5. Tighten the screw until it holds the wire snugly.
4.5 EIA422 SiteScan Web Connector
The Universal Monitor will interface with Liebert’s SiteScan Web
enterprise monitoring system. SiteScan can be used to monitor
analog and digital equipment from a host computer and also to
perform some configuration.
To connect the SiteScan host computer to the Universal Monitor:
1. Turn OFF electrical power to the Universal Monitor.
2. If necessary, remove a conduit knockout to permit wire entry
into the Universal Monitor enclosure.
3. Bring the wire(s) into the Universal Monitor enclosure through
a conduit knockout or access slot.
4. Loosen the appropriate screw and slip the stripped end of the
wire into the terminal block.
5. Tighten the screw until it holds the wire snugly.
4.6 Communications Connections
The Universal Monitor’s Service Terminal Interface offers full
configuration and monitoring capability via the RS232 port and
the phone line connector (see A.2 - Connecting to the
Service Terminal Interface). The phone line connector is
also used for pager notifications and service phone number
options.
4.6.1 RS232 Connector
The RS232 port requires a null modem cable. Connect one end
of the cable to the Universal Monitor’s RS232 port, as shown at
right, and the other end to the COM1 port of a laptop computer
or video terminal.
4.6.2 Phone Line Connector
The Phone Line Connector requires an RJ11 connector.
Connect one end of the connector to the Universal Monitor’s
phone line connector, shown at right, and the other end to a
telephone wall jack.
TB5: COMMON ALARM
(TERMINAL BLOCKS ROTATED IN VIEW)
(BOTTOM)
Q11
R26
R402
P11
+
C
C
NO
CC NO
MO
N ALARM
S
EN
S
TOP
ENABLE
AUDIBLE
(TOP)
NO C NC NO C NC
Common alarm outputs
485
+—
+—
(TOP)
(BOTTOM)
TB1
0
:
CO
MM
S
422
EIA422 SiteScan Web
connector
4
+
(TOP)
(BOTTOM)
TB10: COMMS
4
RJ11: PHONE
PIN 3-TIP
PIN 4-RING
MODEM
Serial interface
connector
(RS232/EIA574)
Phone line
connector
Wiring and Connections - Optional Expansion Board
25
5.0 WIRING AND CONNECTIONS - OPTIONAL EXPANSION BOARD
5.1 Wiring Specifications
Input and output connections to the optional Expansion Board may be made in any order—it is not
necessary, for example, to make all input connections before making any output connections. Use cop-
per conductors only for all wiring.
!CAUTION
Remove all power before installing any wiring to the Expansion Board or changing input or
output connections.
!WARNING
“RISK OF ELECTRIC SHOCK” - More than one disconnect switch may be required to
de-energize the equipment before servicing.
Table 9 Wiring specifications - optional Expansion Board
Connection Supported Wire Type Maximum Wire Length Rating
Digital
Input
18-22 AWG Stranded & Unshielded
18 AWG* (recommended)
Non Plenum - Belden 9740
Plenum - Belden 89740
750 ft. (225m)
Dry Contact
(24VDC,
10 mA)
Digital
Output
18-22 AWG Stranded & Unshielded
18 AWG* (recommended)
Non Plenum - Belden 9740
Plenum - Belden 89740
18 AWG*
(recommended) 20 AWG 22 AWG
240VAC,
2A max.
@3A 50 ft. (15m)
@2A 100 ft. (30m)
@1A 200 ft. (60m)
@3A 40 ft. (12m)
@2A 60 ft. (18m)
@1A 100 ft. (30m)
@3A 25 ft. (7m)
@2A 35 ft. (10m)
@1A 75 ft. (23m)
Communication
EIA485
18-22 AWG Stranded & Shielded
22 AWG* (recommended)
Non Plenum - Belden 9461
Plenum - Belden 88761
3000 ft. (900m) N/A
24VAC Power
Connection
(TB1)
18-22 AWG Stranded & Shielded
18 AWG* (recommended)
Non Plenum - Belden 8770
Plenum - Belden 88770
150 ft. (45m) 24VAC
@0.6A
* Recommended
Wiring and Connections - Optional Expansion Board
26
5.2 Connecting Inputs and Outputs
The Universal Monitor’s optional Expansion Board permits the addition of 16 input and eight output
devices. This section describes how to connect devices to the Expansion Board’s inputs and outputs.
To determine the proper wire size, see Table 9.
5.2.1 Connecting Digital Inputs
The 16 digital inputs are found on the lower portion of the Expansion Board, as shown below. These
inputs are numbered 9 through 24 (the Universal Monitor’s digital inputs are numbered 1 through 8).
To connect an input:
1. Disconnect all electrical power from the Expansion Board.
2. If necessary, remove a conduit knockout to permit wire entry into the Expansion Board enclosure.
3. Bring the wire(s) into the Expansion Board enclosure through a conduit knockout or access slot.
4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.
5. Tighten the screw until it holds the wire snugly.
NOTE
Each terminal block is a removable assembly to permit easier connection of more than one
input at a time. If making multiple connections, grasp the upper portion of a block and pull
firmly until the assembly pulls apart.
After making the connections, push the removed piece back into the portion attached to the
printed wiring assembly until the terminal block pieces lock together.
OUT1
K1
V1 V3 V5 V7 V9 V11 V13 V15
K2 K3 K4 K5 K6 K7 K8
OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
S4 S3 S2 S1
68AO
DEFAULT SETTINGS FOR USE WITH UNIVERSAL MONITOR
EIA485 + (to UM-)
0V
EIA485 - (to UM+)
INPUT TERMINAL BLOCKS
Note numbering keys below terminal blocks;
inputs are numbered from left (9) to right (24)
Numbering keys
Wiring and Connections - Optional Expansion Board
27
5.2.2 Connecting Digital Outputs
The eight digital outputs are found at the top of the Expansion Board, as shown below. These inputs
are numbered 9 through 16. (Note that the digital outputs on the main board of the Universal Monitor
are numbered 1 - 8.)
Each output may be wired according to whether you want the output to be Normally Open or Nor-
mally Closed. The Expansion Board outputs are Form C relay contacts, each with three terminals.
There are two ways to wire the outputs, as shown in Figure 11.
• One wire of the two-wire connection should always be connected to the middle terminal.
• The second wire may be connected to either the N.C. terminal or the N.O. terminal, depending on
how whether you want the contact to be closed or open during a power failure:
• Connect to the N.C. terminal if you want the path to be CLOSED during a power failure, or
• Connect to the N.O. terminal if you want the path to be OPEN during a power failure.
Your choice for wiring the output contacts also determines how to set the fail-safe DIP switches for
proper operation (see 5.2.3 - Setting the Digital Output DIP Switches).
Figure 11 Form C output contact wiring
To connect an output:
1. Disconnect electrical power from the Expansion Board.
2. If necessary, remove a conduit knockout to permit wire entry into the Expansion Board enclosure.
3. Bring the wire(s) into the Expansion Board enclosure through a conduit knockout or access slot.
4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.
5. Tighten the screw until it holds the wire snugly.
!WARNING
“RISK OF ELECTRIC SHOCK” - Hazardous voltage may be present. More than one
disconnect switch may be required to de-energize the equipment before servicing.
!CAUTION
The Expansion Board is designed for use on properly grounded (earthed) 24VAC Class 2
power, 50Hz or 60Hz. The ground wire for the power lead must be wired to the earth ground
terminal (stud located next to the 24VAC terminal block). This equipment is intended to be
installed by a qualified and certified electrician who must review and approve customer-
supplied wiring and circuit breakers, verify correct input and grounded (earthed) connections
to ensure compliance with technical standards and national and local electrical codes.
Segregate and install separate electrical conduits for non-class 2 circuits in accordance with
local building codes.
V2 V4 V6 V8 V10 V12 V14 V16
Multiflex
1
810-306
5
USE COPPER (CU) CONDUCTORS ONLY.
D6
POWER INPUT RELAY OUTPUTS
Numbering
keys
OUTPUT TERMINAL BLOCKS - Note numbering keys above terminal blocks;
outputs are numbered from left (9) to right (16)
N.C. N.O.
Wire connected
to N.C. terminal:
Relay is CLOSED
on power failure
N.C. N.O.
Wire connected
to N.O. terminal:
Relay is OPEN
on power failure
One wire MUST
be connected to
middle terminal
Wiring and Connections - Optional Expansion Board
28
5.2.3 Setting the Digital Output DIP Switches
Each digital output on the optional Expansion Board has an associated DIP switch that can deter-
mine its operation in the event of loss of communication with the Universal Monitor or loss of power.
When the Universal Monitor calls for an Expansion Board output to be ON, it sends a command to the
Expansion Board to turn the output to the ON state; this is signified by the output LED being ON.
The behavior of the output when it is ON is determined by the position of the DIP switch.
The DIP switches for the outputs are on a switch bank on the right side of the Expansion Board, as
shown below. Each switch corresponds to an output on the board in order from left to right—for exam-
ple, DIP switch 1 corresponds to Output 9; DIP switch 2 corresponds to Output 10.
Tables 10 and 11 show how to set the DIP switch for each output based on how the output is wired
(see 5.2.2 - Connecting Digital Outputs) and how you want it to perform during normal operation,
when communication with the Universal Monitor is lost or when power fails.
The Expansion Board comes from the factory with all digital output DIP switches in the OFF position
(normally open). The DIP switch setting for each digital output can be changed to ON (normally closed).
To change the state of any output to the factory default of NO (Normally Open) or to NC (Normally
Closed), move each switch to the appropriate position:
• Move the switch down to the OFF position for NO (Normally Open)—the default setting.
• Move the switch up to the ON position for NC (Normally Closed).
NOTE
After a loss of communications with the Universal Monitor, there is a time delay—about five
minutes—before the Expansion Board changes the state of an output.
Table 10 DIP switch setting - outputs wired as Normally Closed (N.C.)
If Output
DIP Switch
is:
State of Output When:
Light is
ON
Light is
OFF
Communication
with UM is Lost
Power
Fails
Up (ON) Closed Open Closed Closed
Down (OFF) Open Closed Closed Closed
Table 11 DIP switch setting - outputs wired as Normally Open (N.O.)
If Output
DIP Switch
is:
State of Output When:
Light is
ON
Light is
OFF
Communication
with UM is Lost
Power
Fails
Up (ON) Open Closed Open Open
Down (OFF) Closed Open Open Open
OUT1
K1
V1 V3 V5 V7 V9 V11 V13 V15
V2 V4 V6 V8 V10 V12 V14 V16
K2 K3 K4 K5 K6 K7 K8
OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8
S4 S3 S2 S1
Multiflex 168AO
810-3065
DEFAULT SETTINGS FOR USE WITH UNIVERSAL MONITOR
USE COPPER (CU) CONDUCTORS ONLY.
D6
POWER INPUT
EIA485 + (to UM-)
0V
EIA485 - (to UM+)
RELAY OUTPUTS
Digital output
DIP switches
Optional
Expansion
Board
N.C. N.O.
Wire connected
to N.C. terminal
N.C. N.O.
Wire connected
to N.O. terminal
Wiring and Connections - Optional Expansion Board
29
5.3 Connect to the Universal Monitor
Two steps are required to establish connection between the optional Expansion Board and the Uni-
versal Monitor.
5.3.1 Connect EIA485 Connectors to Main Board
To connect the optional Expansion Board to the Universal Monitor:
1. Turn OFF electrical power to the Universal Monitor and disconnect power from the Expansion
Board.
2. If necessary, remove a conduit knockout to permit wire entry into each enclosure.
3. Bring the wire(s) into each enclosure through a conduit knockout or access slot.
4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block,
connecting the cables as shown in the figure below):
• Connect the Universal Monitor 485 connector UM- to Expansion Board connector EIA485+.
• Connect the Universal Monitor 485 connector UM+ to Expansion Board connector EIA485-.
5. Tighten each screw until it holds the wire snugly.
5.3.2 Enable the Connection via Firmware
After making the cable connections described in the previous section, you must specify the Expansion
Board as connected using either the LCD or Service Terminal Interface.
For instructions, refer to the appropriate section:
• LCD interface (see 9.10 - Setup Exp Board - Optional Expansion Board)
• Service Terminal Interface (see A.6.8 - Connect Expansion Board)
485
+—
+—
(TOP)
(BOTTOM)
TB1
0
:
CO
MM
S
422
S4 S3 S2 S1
Multiflex 168AO
810-3065
D6
POWER INPUT
EIA485 + (to UM-)
0V
EIA485 - (to UM+)
UNIVERSAL MONITOR
EIA485 connector
OPTIONAL EXPANSION BOARD
EIA485 connector
Connect
UM- to
EIA485+
Connect
UM+ to
EIA485-
EIA485+
EIA485-
UM-
UM+
Overview of Menus
30
6.0 OVERVIEW OF MENUS
There are two ways to access the Universal Monitor: the LCD on the front of the enclosure and the
Service Terminal Interface, which is accessible through any computer using a communications pro-
gram. Many viewing and configuration tasks can be performed through either interface, but some are
available only through the Service Terminal Interface.
• Step-by-step instructions for all functions appear in Sections 7.0 through 9.0. These instructions
use examples of LCD screens to illustrate most functions, except those not available via the LCD.
• Examples of all Service Terminal Interface screens appear in Appendix A - Service Terminal
Interface, along with instructions on how to connect to the Service Terminal Interface.
Table 12 lists all Universal Monitor functions and shows whether they can be performed through the
LCD interface and where to find information.
Table 12 Guide to Universal Monitor functions
Function
Can be performed via: Where to find:
LCD
Service
Terminal
Instructions on
using function
Service Terminal
screen examples
VIEW STATUS FUNCTIONS
View Active Alarms ✔✔ page 33 page 93
View Alarm Log ✔✔ page 34 page 94
View Event Log ✔✔ page 35 page 95
View Trend Log ✔✔ page 36 page 96
View Input Status ✔✔ page 37 page 97
View Output Status ✔✔ page 38 page 98
View Pager Numbers ✔✔ page 39 page 99
SILENCE ALARM & BACK UP LOGS FUNCTIONS
Silence Alarm (On the LCD, press any key to silence an alarm) ✔✔ page 40 page 100
Back Up Log Files — ✔page 41 page 101
SYSTEM & CONTROL FUNCTIONS
Login ✔✔ page 43 page 104
Setup System ✔✔ page 45 page 105
Setup Input ✔✔ page 45 page 106
Setup Common Alarm ✔✔ page 48 page 108
Setup Sensor ✔✔ page 49 page 109
Setup I/O Matrix ✔✔ page 55 page 111
Setup Output ✔✔ page 58 page 117
Pager Setup - Pager Number & PIN ✔✔ page 64 page 119
Pager Setup - Communications Check — ✔page 66 page 119
Modem Setup - Initialization String ✔✔ page 60 page 120
Modem Setup - Enter Universal Monitor Phone Number — ✔page 62 page 120
Modem Setup - Enable Modem Diagnostic Messages — ✔page 62 page 120
Modem Setup - Change Modem Dial Prefix — ✔page 62 page 120
Modem Setup - Change Modem Hang Up Delay After a Call — ✔page 62 page 120
Setup System Info ✔✔ page 68 page 121
Change Password ✔✔ page 69 page 121
Change Date & Time/Automatic Daylight Saving Time ✔✔ page 69 page 122
Setup Site ID ✔✔ page 70 page 122
Connect Battery ✔✔ page 70 page 123
Backup and Upload Configuration File — ✔page 71 page 123
Setup Serv Ph Num - Enter Phone Number ✔✔ page 74 page 124
Setup Serv Ph Num - Communications Check — ✔page 75 page 124
Factory Defaults ✔✔ page 76 page 125
Perform Firmware Update — ✔page 76 page 125
Initiate Remote Alarm Test — ✔page 78 page 126
Setup Exp Board - Optional Expansion Board ✔✔ page 79 page 127
Manual Output Ctrl ✔✔ page 80 page 128
Clear Alarms & Logs ✔✔ page 81 page 130
Clear Active Alarms ✔✔ page 81 page 130
Clear the Alarm Log ✔✔ page 81 page 130
Clear the Event Log ✔✔ page 82 page 131
Clear the Trend Logs ✔✔ page 82 page 131
Overview of Menus
31
6.1 Opening Screen Overview
The Universal Monitor displays the Opening Screen at startup, as shown in Figure 12.
• If any alarms are active, the Current Alarm screen appears. (Pressing any key on the LCD keypad
will silence the audible alarm.)
• If any analog input sensors are connected, the LCD screen will alternately display the Opening
Screen and a screen showing the analog value of each sensor.
If no alarms are present, the Main Menu appears.
6.2 Main Menu Overview
The Main Menu offers access to all functions within the panel. As shown in Table 13, the functions
are organized into three sections with step-by-step instructions.
6.3 LCD Menu Overview
Figure 12 shows an overview of the initial screens available through the LCD interface. For compa-
rable information about the Service Terminal Interface screens, see A.3 - Overview of Menus.
Figure 12 LCD Menu overview
Table 13 Primary Functions Overview
Section Description
7.0 -View Status Options
(both LCD and Service
Terminal Interface)
These features are available to all users. This permits all personnel to check the
status of any monitored equipment or location. From this menu, any user may:
• View current monitoring data—active alarms and the status of inputs and outputs
• View data stored in alarm, event and trend logs
• View pager numbers
8.0 -Silence Alarm & Backup
Log Files (Service
Terminal Interface only)
These features—available via the Service Terminal Interface only—allow users to:
• Silence the audible alarm
• Back up the alarm, event and trend logs
9.0 -System and Control
Options (some functions
available via Service
Terminal Interface only)
These options require a password. Authorized users may:
• Configure the Universal Monitor
• Override automatic control of outputs to force an output ON or OFF
• Clear active alarms and delete all records in the alarm, event and trend logs
Opening Screen
UNIVERSAL MONITOR
DD-MON-YY HR:MM:SS
VX.XXX.X
PRESS ↵=STATUS/SETUP
(If any alarms detected)
Current Alarm screen
(see 7.1 - View Active Alarms)
Main Menu
VIEW STATUS
SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
“View Status” selected See Section “System & Control” selected See Section
> VIEW STATUS
SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
7.0 VIEW STATUS
> SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
9.0
View Status Menu
(All users - no password) See Section
System & Control Menu
(Password required) See Section
VIEW ACTIVE ALARMS
VIEW ALARM LOG
VIEW EVENT LOG
VIEW TREND LOG
VIEW INPUT STATUS
VIEW OUTPUT STATUS
VIEW PAGER NUMBERS
7.1
7.2
7.3
7.4
7.5
7.6
7.7
SETUP SYSTEM
MANUAL OUTPUT CTRL
CLEAR ALARMS & LOGS
9.2
9.11
9.12
View Status Options
32
7.0 VIEW STATUS OPTIONS
The View Status menu allows any user to view currently active alarms, monitoring data stored in the
alarm, event and trend logs, the status of all inputs and outputs, and the four pager numbers. The
arrows ↑↓ are used to scroll through the menu. The Enter ↵ key is used to select the menu item.
This section presents step-by-step instructions for each of the following options:
• View Active Alarms
•View Alarm Log
•View Event Log
• View Trend Log
• View Input Status
• View Output Status
• View Pager Numbers
Figure 13 shows the main options available from the View Status menu.
Figure 13 Menu overview - View Status menu
NOTE
For ease of understanding, this section uses the LCD interface to illustrate most instructions,
except for features that are available only through the Service Terminal Interface. All Service
Terminal Interface screens appear in Appendix A - Service Terminal Interface.
Opening Screen
UNIVERSAL MONITOR
DD-MON-YY HR:MM:SS
VX.XXX.X
PRESS ↵=STATUS/SETUP
Main Menu
> VIEW STATUS
SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
View Status
VIEW ACTIVE ALARMS
VIEW ALARM LOG
VIEW EVENT LOG
VIEW TREND LOG
VIEW INPUT STATUS
VIEW OUTPUT STATUS
VIEW PAGER NUMBERS
View Active Alarms View Alarm Log View Event Log View Trend Log
> ACTIVE ALARM 33/33
SENSOR_1 101.0 DEG
HIGH SETPOINT ALARM
SENSOR_2 ------ DEG
SENSOR PROBLEM
INPUT_07 ALARM
CONTACT OPEN
BATTERY
CHECK BATTERY
See
Section
7.1
> ALARM RECORD 99/99
SENSOR_2 80.0 DEG
HIGH SETPOINT ALARM
29-AUG-02 09:29:10
MODEM
INTERNAL FAULT
29-AUG-02 09:20:00
INPUT_08 ALARM
CONTACT CLOSED
29-AUG-02 07:30:00
See
Section
7.2
> EVENT RECORD 99/99
PAGER
UNSUCCESSFUL PAGE
07-MAY-02 10:07:00
OUTPUT01 MAN ON
CONTACT CLOSED
06-MAY-02 02:47:03
OUTPUT08 ON
CONTACT OPEN
05-MAY-02 05:22:17
See
Section
7.3
SENSOR TO VIEW?
> SENSOR_1
SENSOR_2
SENSOR_3
SENSOR_4
See
Section
7.4
> TREND LOG 100/100
SENSOR_1 75.4 DEG
NORMAL
28-AUG-02 15:45:51
View Input Status View Output Status View Pager Numbers
INPUT / STATUS
> SENSOR_1 +80.00 DEG
SENSOR_2 ------ DEG
SENSOR_3
SENSOR_4 +79.50 RH
INPUT_01 NORMAL
INPUT_02 ALARM
INPUT_03 EVENT
INPUT_04 ALARM
INPUT_05 ALARM
INPUT_06 EVENT
INPUT_07 NORMAL
INPUT_08 NORMAL
INPUT_09 NORMAL
.
.
.
INPUT_24 NORMAL
See
Section
7.5
OUTPUT / STATUS
> OUTPUT01 ON
OUTPUT02 OFF
OUTPUT03 ON
OUTPUT04 MAN ON
OUTPUT05 ON
OUTPUT06 OFF
OUTPUT07 MAN OFF
OUTPUT08 ON
OUTPUT09 OFF
.
.
.
OUTPUT16 OFF
See
Section
7.6
PAGER TO VIEW?
> PAGER NUMBER 1
PAGER NUMBER 2
PAGER NUMBER 3
PAGER NUMBER 4
See
Section
7.7
VIEW PAGER NUMBER
VIEW PAGER PIN
PAGER 1 NUMBER
9,,18005551212##
PAGER 1 PIN
01234567891011121344
View Status options
8 add’l
outputs
for
optional
Expansion
Board
16 additional
inputs for
optional
Expansion
Board
View Status Options
33
7.1 View Active Alarms
The Active Alarm screen displays all alarms that are occurring, up to a
maximum of 33.
A Current Alarm screen appears automatically whenever an alarm
occurs—except during setup. This screen can display only the two most
recent active alarms. To view any other active alarms, use the View
Active Alarms feature.
You may view active alarms at any time by using the following steps:
• From the Main Menu, use the arrows ↑↓ to choose View Status, as
shown at right, and then press Enter ↵.
• From the View Status Menu, use the arrows ↑↓ to choose View
Active Alarms and press Enter ↵.
7.1.1 Active Alarms
The Active Alarms screen displays up to 33 records; it shows any active
alarm and any Latched alarm that has not been cleared. Examples of
alarms include inputs in alarm status, a low battery condition and a
loss of connection to an analog input. When any alarms are present, the
Active Alarms screen shows descriptive details for each alarm:
• the source of the alarm (for example, SENSOR_1 or BATTERY)
• the status of an input or output (101.0 DEG)
• a brief description of the problem (HIGH SETPOINT ALARM or CHECK
BATTERY)
If there are no active alarms, the screen displays the message:
NO ALARMS PRESENT
Viewing Additional Screens
There may be up to 33 records of alarm data.
• To view additional records, use the arrows ↑↓.
• To return to the previous screen, press the ESC key.
Clearing Active Alarms
To clear all active alarms, see 9.12 - Clear Alarms & Logs. Alarm records are stored in the Alarm
Log.
Main Menu
> VIEW STATUS
SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
View Status Menu
> VIEW ACTIVE ALARMS
VIEW ALARM LOG
VIEW EVENT LOG
VIEW TREND LOG
VIEW INPUT STATUS
VIEW OUTPUT STATUS
VIEW PAGER NUMBERS
Active Alarms
> ACTIVE ALARM 33/33
SENSOR_1 101.0 DEG
HIGH SETPOINT ALARM
SENSOR_2 ------ DEG
SENSOR PROBLEM
INPUT_07 ALARM
CONTACT OPEN
BATTERY
CHECK BATTERY
View Status Options
34
7.2 View Alarm Log
The Alarm Log contains up to 99 records of alarms that have occurred.
Records are added to this log as alarms occur.
To view the Alarm Log:
• From the Main Menu, use the arrows ↑↓ to choose View Status,
then press Enter ↵.
• From the View Status Menu, use the arrows ↑↓ to choose View
Alarm Log, then press Enter ↵.
7.2.1 Alarm Log
The Alarm Log screen displays up to 99 records showing alarm data,
including input alarms and other conditions, such as loss of power or
low battery. If the log contains any alarm records, the Alarm Log screen
displays details for each alarm:
• the source of the alarm (for example, SENSOR_2 or MODEM)
• the status of an input or output (80.0 DEG)
• a brief description of the problem (HIGH SETPOINT ALARM or INTER-
NAL FAULT)
• the date and time the alarm occurred
Table 14 shows conditions that the alarm log records for digital inputs
and analog inputs and in the panel itself.
If there are no alarms in the log, the screen displays the message:
NO ALARMS
Viewing Additional Screens
There may be up to 99 records of alarm data.
• To view additional records, use the arrows ↑↓.
• To return to the previous screen, press the ESC key.
7.2.2 Backing Up the Alarm Log (Service Terminal Interface only)
The alarm log is stored as a file in the Universal Monitor; it can hold no more than 99 records. When
the log is full, the oldest records are deleted from the end of the file as new alarm records are added at
the beginning.
You may back up the alarm log file to a remote computer using the Service Terminal Interface, as
described in 8.2 - Back Up Log Files (Service Terminal Interface only).
To delete all records in the alarm log, see 9.12 - Clear Alarms & Logs.
Table 14 Alarm log conditions
SOURCE Digital Input Analog Input Panel
CONDITIONS
RECORDED
ALARM
NORMAL
HIGH SETPOINT ALARM
LOW SETPOINT ALARM
RETURN TO NORMAL
SENSOR PROBLEM (denoted by dashes ------)
LOSS OF POWER
LOW BATTERY
CHECK BATTERY
BATTERY UNPLUGGED
ALARM SILENCED
MODEM INTERNAL FAULT
ALARMS CLEARED
EXP BRD LOSS OF COMM
EXP BRD RESTORE COMM
Main Menu
> VIEW STATUS
SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
View Status Menu
VIEW ACTIVE ALARMS
> VIEW ALARM LOG
VIEW EVENT LOG
VIEW TREND LOG
VIEW INPUT STATUS
VIEW OUTPUT STATUS
VIEW PAGER NUMBERS
Alarm Log
> ALARM RECORD 99/99
SENSOR_2 80.0 DEG
HIGH SETPOINT ALARM
29-AUG-02 09:29:10
MODEM
INTERNAL FAULT
29-AUG-02 09:20:00
INPUT_08 ALARM
CONTACT CLOSED
29-AUG-02 07:30:00
View Status Options
35
7.3 View Event Log
In addition to alarms, the Universal Monitor tracks other changes in
the Event Log to assist users with verifying operational and trouble-
shooting problems. Events reflect changes in the status of an input that
is defined as an event or the change of state of an output (i.e., manually
forced ON or OFF). Other events may be informational, such as a user
login or an unsuccessful page attempt. The Event Log contains up to
99 records of events, which are added as they occur.
To view the Event Log:
• From the Main Menu, use the arrows ↑↓ to choose View Status,
then press Enter ↵.
• From the View Status Menu, use the arrows ↑↓ to choose View
Event Log, then press Enter ↵.
7.3.1 Event Log
The Event Log screen displays up to 99 recent events. If the log con-
tains any event records, the Event Log screen displays details for each
event:
• the event source (for example, PAGER or OUTPUT01)
• the status of an input or output (MAN ON)
• a brief description of the event (UNSUCCESSFUL PAGE or CONTACT
CLOSED)
• the date and time the event occurred
Table 15 shows conditions that the event log records for inputs and outputs and in the panel itself.
If there are no records in the log, the screen displays the message:
NO EVENTS
Viewing Additional Screens
There may be up to 99 records of event data.
• To view additional records, use the arrows ↑↓.
• To return to the previous screen, press the ESC key.
7.3.2 Backing Up the Event Log (Service Terminal Interface only)
The event log is stored as a file in the Universal Monitor; it can hold no more than 99 records. When
the log is full, the oldest records are deleted from the end of the file as new event records are added at
the beginning.
You may back up the event log file to a remote computer using the Service Terminal Interface, as
described in 8.2 - Back Up Log Files (Service Terminal Interface only).
To delete all records in the event log, see 9.12 - Clear Alarms & Logs.
Table 15 Event log conditions
SOURCE Digital Input Analog Input Digital Output Panel
CONDITIONS
RECORDED
EVENT
NORMAL
HIGH SETPOINT EVENT
LOW SETPOINT EVENT
RETURN TO NORMAL
SENSOR PROBLEM
(denoted by dashes ------)
MAN ON
MAN OFF
AUTO
HW MAN ON
ON
OFF
ALARMS CLEARED
ALARM SILENCED
DIAL OUT TEST PASSED
DIAL OUT TEST FAILED
UNSUCCESSFUL PAGE
MODEM RESET
TIME & DATE SET
USER LOGIN
Main Menu
> VIEW STATUS
SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
View Status Menu
VIEW ACTIVE ALARMS
VIEW ALARM LOG
> VIEW EVENT LOG
VIEW TREND LOG
VIEW INPUT STATUS
VIEW OUTPUT STATUS
VIEW PAGER NUMBERS
Event Log
> EVENT RECORD 99/99
PAGER
UNSUCCESSFUL PAGE
07-MAY-02 10:07:00
OUTPUT01 MAN ON
CONTACT CLOSED
06-MAY-02 02:47:03
OUTPUT08 ON
CONTACT OPEN
05-MAY-02 05:22:17
View Status Options
36
7.4 View Trend Log
The Universal Monitor takes readings of configured analog input sen-
sors at regular intervals and stores them in four separate trend logs,
one for each sensor. The time interval is 30 minutes. Each log contains
up to 100 records.
Follow these steps to select a sensor and view its trend log:
7.4.1 Select a Sensor
To select a sensor:
• From the Main Menu, use the arrows ↑↓ to choose View Status,
then press Enter ↵.
• From the View Status Menu, use the arrows ↑↓ to choose View
Trend Log, then press Enter ↵.
• From the Sensor Selection Menu, use the arrows ↑↓ to choose the
sensor you want to view—Sensor_1 in the example at right—and
press Enter ↵.
7.4.2 View a Trend Log
The Trend Log screen displays up to 100 records for the selected sensor.
If the log contains records, the screen displays details for each reading:
• the name of the selected sensor (for example, SENSOR_1)
•the reading (
75.4 DEG)
• a brief description of the reading status (NORMAL)
• the date and time of the reading
Table 16 shows conditions that the trend log records for analog inputs.
Each analog input has its own trend log.
If there are no records in the log, the screen displays the message:
NO TRENDS
Viewing Additional Screens
There may be up to 100 records of trend data for the selected sensor.
• To view additional records, use the arrows ↑↓.
• To return to the previous screen, press the ESC key.
7.4.3 Backing Up the Trend Log (Service Terminal Interface only)
The four trend logs are stored as files in the Universal Monitor, with a maximum of 100 records per
sensor. When a log is full, the oldest records are deleted from the end of the file as new trend records
are added at the beginning.
You may back up each trend log file to a remote computer using the Service Terminal Interface, as
described in 8.2 - Back Up Log Files (Service Terminal Interface only).
To delete all records in the trend logs, see 9.12 - Clear Alarms & Logs.
Table 16 Trend log conditions
SOURCE Analog Input
CONDITIONS
RECORDED
LOW SETPOINT ALARM
LOW SETPOINT EVENT
HIGH SETPOINT ALARM
HIGH SETPOINT EVENT
RETURN TO NORMAL
NORMAL
SENSOR PROBLEM (denoted by dashes ------)
Main Menu
> VIEW STATUS
SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
View Status Menu
VIEW ACTIVE ALARMS
VIEW ALARM LOG
VIEW EVENT LOG
> VIEW TREND LOG
VIEW INPUT STATUS
VIEW OUTPUT STATUS
VIEW PAGER NUMBERS
Select Sensor Menu
SENSOR TO VIEW?
> SENSOR_1
SENSOR_2
↑↓=NEXT ↵=SELECT
SENSOR_3
SENSOR_4
Trend Log
> TREND LOG 100/100
SENSOR_1 75.4 DEG
NORMAL
28-AUG-02 15:45:51
SENSOR_1 70.5 DEG
LOW SETPOINT EVENT
28-AUG-02 15:15:51
SENSOR_1 79.9 DEG
RETURN TO NORMAL
28-AUG-02 14:45:21
View Status Options
37
7.5 View Input Status
The Input Status option allows you to view the current status of all
inputs: the four analog sensor inputs and the eight digital inputs. If the
optional Expansion Board is used, the additional 16 digital inputs can
also be viewed.
To view the Input Status:
• From the Main Menu, use the arrows ↑↓ to choose View Status,
then press Enter ↵.
• From the View Status Menu, use the arrows ↑↓ to choose View
Input Status, then press Enter ↵.
7.5.1 Input Status
The Input Status screen displays the status of each analog sensor and
digital input.
Analog Sensor Inputs
The following details are displayed for analog sensor inputs:
• the name of the analog sensor input (for example, SENSOR_1)
• the current reading (+80.00 DEG)—values are updated constantly
while being viewed
There are three possible states for an analog input, as shown in
Table 17.
Digital Inputs
The following details appear for digital inputs:
• the name of the digital input (for example, INPUT_01)
• the current status (NORMAL)—values are updated constantly while
being viewed
There are three possible states for a digital input, as shown in Table 18.
Viewing Additional Input Data
All input data may be viewed by scrolling beyond the four lines that appear on the LCD at one time:
• To view all inputs, use the arrows ↑↓.
• To return to the previous screen, press the ESC key.
Table 17 Analog input states
State Description
Functional Reading—-for example, +80.00 DEG or +79.50 RH
Problem with
connection
Dashes (------)
Not configured Blank
NOTE
If the status displays dashes (------), the Universal Monitor
was unable to take a reading. There may be a connection
problem.
If the status is blank, the sensor is not configured as being
connected.
Table 18 Digital input states
State Description
NORMAL In normal state
ALARM In alarm status (for an input configured as alarmable)
EVENT An event has occurred (for an input configured as an event)
Main Menu
> VIEW STATUS
SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
View Status Menu
VIEW ACTIVE ALARMS
VIEW ALARM LOG
VIEW EVENT LOG
VIEW TREND LOG
> VIEW INPUT STATUS
VIEW OUTPUT STATUS
VIEW PAGER NUMBERS
Input Status
INPUT / STATUS
> SENSOR_1 +80.00 DEG
SENSOR_2 ------ DEG
SENSOR_3
SENSOR_4 +79.50 RH
INPUT_01 NORMAL
INPUT_02 ALARM
INPUT_03 EVENT
INPUT_04 ALARM
INPUT_05 ALARM
INPUT_06 EVENT
INPUT_07 NORMAL
INPUT_08 NORMAL
INPUT_09 NORMAL
INPUT_10 ALARM
INPUT_11 EVENT
INPUT_12 ALARM
INPUT_13 ALARM
INPUT_14 EVENT
INPUT_15 NORMAL
INPUT_16 NORMAL
INPUT_17 NORMAL
INPUT_18 ALARM
INPUT_19 EVENT
INPUT_20 ALARM
INPUT_21 ALARM
INPUT_22 EVENT
INPUT_23 NORMAL
INPUT_24 NORMAL
NOTE: 16 additional inputs
(INPUT_09 thru INPUT_24)
for optional Expansion Board
View Status Options
38
7.6 View Output Status
The Output Status option allows you to view the current status of all
eight outputs. If the optional Expansion Board is used, the additional
eight digital outputs can also be viewed.
To view the Output Status:
• From the Main Menu, use the arrows ↑↓ to choose View Status,
then press Enter ↵.
• From the View Status Menu, use the arrows ↑↓ to choose View
Output Status, then press Enter ↵.
7.6.1 Output Status
The Output Status screen displays the status of each digital output.
The following details appear for digital outputs:
• the name of the output (for example, OUTPUT01)
• the current status (ON)—values are updated constantly while being
viewed
There are five possible states for a digital output, as shown in
Table 19.
Viewing Additional Output Data
All output data may be viewed by scrolling beyond the four lines that
appear on the LCD at one time:
• To view all outputs, use the arrows ↑↓.
• To return to the previous screen, press the ESC key.
Table 19 Digital output states
State Description
ON Automatic Controlled by Universal Monitor
OFF Automatic
MAN ON Manually ON This output forced ON or OFF
via Manual Output Ctrl menu or
SiteScan Web
MAN OFF Manually OFF
HW MAN ON Manually ON
(all outputs)
All outputs forced ON
via hardware switch on circuit board
Main Menu
> VIEW STATUS
SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
View Status Menu
VIEW ACTIVE ALARMS
VIEW ALARM LOG
VIEW EVENT LOG
VIEW TREND LOG
VIEW INPUT STATUS
> VIEW OUTPUT STATUS
VIEW PAGER NUMBERS
Output Status
OUTPUT / STATUS
> OUTPUT01 ON
OUTPUT02 OFF
OUTPUT03 ON
OUTPUT04 MAN ON
OUTPUT05 ON
OUTPUT06 OFF
OUTPUT07 MAN OFF
OUTPUT08 ON
OUTPUT09 ON
OUTPUT10 OFF
OUTPUT11 ON
OUTPUT12 MAN ON
OUTPUT13 ON
OUTPUT14 OFF
OUTPUT15 MAN OFF
OUTPUT16 ON
NOTE: 8 additional outputs
(OUTPUT09 thru OUTPUT16)
for optional Expansion Board
View Status Options
39
7.7 View Pager Numbers
The Universal Monitor may be set up to dial pager numbers when an
alarm is detected. Up to four pagers may be configured, as described in
9.8 - Setup System - Setup Modem & Pagers.
The View Pager Numbers option allows you to view the pager numbers
and PINs for all configured pagers. Use the following steps to select a
pager and view its information.
7.7.1 Select a Pager
To select a pager:
• From the Main Menu, use the arrows ↑↓ to choose View Status,
then press Enter ↵.
• From the View Status Menu, use the arrows ↑↓ to choose View
Pager Numbers, then press Enter ↵.
• From the Pager Selection screen, use the arrows ↑↓ to choose the
pager you want to view—Pager Number 1 in the example at
right—and press Enter ↵.
• Use the following steps to view a pager number or PIN for the
selected pager.
7.7.2 View a Pager Number
To view a pager number:
• Choose View Pager Number from the Pager Menu and press
Enter ↵.
• The Pager Number screen displays the number that is configured
for the selected pager.
In the example at right, the telephone number is preceded by A to
dial an alphanumeric pager and includes a comma (,) to pause two
seconds after dialing “1” before proceeding to dial the area code and
number. To change this number, see 9.8.3 - Pager Setup - Pager
Number and PIN.
• Press ESC to return to the Pager Menu.
7.7.3 View a Pager PIN
To view a pager PIN:
• Choose View Pager PIN from the Pager Menu and press
Enter ↵.
• The Pager PIN screen displays the PIN that is configured for the
selected pager. To change this number, see 9.8 - Setup System -
Setup Modem & Pagers.
• Press ESC to return to the Pager Menu.
Main Menu
> VIEW STATUS
SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
View Status Menu
VIEW ACTIVE ALARMS
VIEW ALARM LOG
VIEW EVENT LOG
VIEW TREND LOG
VIEW INPUT STATUS
VIEW OUTPUT STATUS
> VIEW PAGER NUMBERS
Pager Selection
PAGER TO VIEW?
> PAGER NUMBER 1
PAGER NUMBER 2
PAGER NUMBER 3
PAGER NUMBER 4
Pager Menu
> VIEW PAGER NUMBER
VIEW PAGER PIN
Pager Number
PAGER 1 NUMBER
A1,8005551212
Pager Menu
VIEW PAGER NUMBER
> VIEW PAGER PIN
Pager PIN
PAGER 1 PIN
01234567891011121344
Silence Alarm & Backup Log Files (Service Terminal Interface)
40
8.0 SILENCE ALARM & BACKUP LOG FILES (SERVICE TERMINAL INTERFACE)
This section describes two features that are available in the Service Terminal Interface:
• Silence Alarm
• Backup Log Files
8.1 Silence Alarm (Service Terminal Interface)
The Silence Alarm menu item allows you to silence the audible alarm and reset the Common Alarm
Relay output if the common alarm is configured to reset with silence.
This menu item is available only through the Service Terminal Interface and SiteScan Web connec-
tion.
To silence the alarm remotely through the Service Terminal Interface:
• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see
A.2 - Connecting to the Service Terminal Interface).
• At the Main Menu, enter 8 (Silence Alarm).
• At the Silence Alarm menu, shown below, enter 1 to silence the audible alarm immediately. (To
exit without silencing the alarm, enter 2 or press the Escape key.)
• A confirmation message appears: “Alarm has been silenced.”
NOTE
An alarm may also be silenced by pressing any key on the LCD keypad on the front
of the Universal Monitor. The LCD does not offer Silence Alarm as a menu item.
Silence Alarm (Service Terminal Interface only)
SILENCE ALARM
Silence alarm and reset
common alarm relay if
common alarm relay is
configured to reset with
silence alarm
1=SILENCE ALARM
2=RETURN TO MAIN MENU
SELECT A NUMBER:1
>ALARM HAS BEEN SILENCED
NOTE
Through SiteScan Web, this option is available via the Universal Monitor
Graphic Screen.
Silence Alarm & Backup Log Files (Service Terminal Interface)
41
8.2 Back Up Log Files (Service Terminal Interface only)
The Universal Monitor maintains three types of logs—alarm, event and trend—that may be backed
up to a remote computer.
This feature is available only through the Service Terminal Interface.
To back up any of the alarm, event or trend logs:
1. Connect to the Universal Monitor either from a remote computer or through the RS232 port (see
A.2 - Connecting to the Service Terminal Interface).
2. At the Main Menu, enter 9 (Backup Log Files).
3. At the Backup Log Files menu, as shown below, enter a number for the type of file you want to
back up:
• Enter 1 to back up the Alarm Log
• Enter 2 to back up the Event Log
• Enter 3 to back up the Trend Log for the first sensor (Sensor_1)
• Enter 4 to back up the Trend Log for the second sensor (Sensor_2)
• Enter 5 to back up the Trend Log for the third sensor (Sensor_3)
• Enter 6 to back up the Trend Log for the fourth sensor (Sensor_4)
4. At the prompt to initiate a backup of the selected log file, enter Y (Yes - begin) or N (No - cancel).
The current setting appears in brackets—[N] in the following example.
Backup Log Files - Alarm Log File (Service Terminal Interface only)
BACKUP LOG FILES
Backup alarm, event and trend log files
1=BACKUP ALARM LOG FILE
2=BACKUP EVENT LOG FILE
3=BACKUP TREND LOG FILE-SENSOR_1
4=BACKUP TREND LOG FILE-SENSOR_2
5=BACKUP TREND LOG FILE-SENSOR_3
6=BACKUP TREND LOG FILE-SENSOR_4
7=RETURN TO MAIN MENU
SELECT A NUMBER:1
>INITIATE A BACKUP OF ALARM LOG-YES(Y) OR NO(N)?
>[N]
>[
Silence Alarm & Backup Log Files (Service Terminal Interface)
42
5. At the top of the HyperTerminal window, shown below, click on Transfer, then on Receive File.
6. In the Receive File window, as shown above:
• In the Place Received File in the Following Folder box, enter the name and location of the
folder where the configuration file should be placed—for example, C:\downloads—or click
on the Browse button to locate the folder.
• In the Use Receiving Protocol box, select Xmodem from the drop-down list.
• Click on the Receive button. (To close the window without backing up the file, click on Close
or Cancel.)
7. In the Receive Filename window, enter a name for the log file—Alarm.log in the example above.
8. When the transfer is complete, a confirmation message appears in the Service Terminal Interface
window: “Backup Successful.”
9. The display returns to the Backup Log Files menu. You may choose another type of log file to back
up (return to Step 3) or press 7 (or Escape) to return to the Main Menu.
After backing up a log file, you may want to delete all records in the Universal Monitor’s log of that
type. See 9.12 - Clear Alarms & Logs for details.
NOTE
The following instructions refer to the Microsoft® Windows® HyperTerminal program. These
steps may vary for other communications programs.
Enter filename -
for example,
alarm.log
Select Xmodem
Enter folder
System and Control Options
43
9.0 SYSTEM AND CONTROL OPTIONS
The System and Control menu allows you to configure the Universal Monitor—setting up inputs and
outputs and an input/output matrix to trigger actions, the modem and pagers, and system features
such as date and time. This menu also provides a vehicle for manually changing the state of an output
to ON or OFF, clearing active alarms and deleting records from the Universal Monitor’s alarm log,
event log and trend logs.
The arrows ↑↓ are used to scroll through the menu. The Enter ↵ key is used to select the menu item
and enter new information. Table 20 shows characters that may be entered in labels and values.
The System and Control options require a password to prevent unauthorized users from making
changes to the system.
This section presents step-by-step instructions for each of the following:
•Login - enter the password
•Setup System - configure inputs, outputs, modem, pagers, system features
•Manual Output Ctrl - manually override automatic control of outputs; release the override
•Clear Alarms & Logs - clear active alarms; delete records from the alarm, event and trend logs
9.1 Login
Users must enter a password to access any of the system and control
options. The password consists of four characters (see Table 20 for
valid characters). (To set up or change the password, see 9.9.1 -
Change Password.)
To log in:
• From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵, as shown at right.
• Use the arrows ↑↓ to choose System and Control, and press
Enter ↵. The Login menu appears.
• To enter your password:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
The System and Control Menu appears next, with these options that
are described in the following sections:
• Setup System (Section 9.2 - Section 9.9)
• Manual Output Ctrl (Section 9.11)
•Clear Alarms & Logs (Section 9.12)
NOTE
For ease of understanding, this section uses the LCD interface to illustrate most instructions,
except for features that are available only through the Service Terminal Interface. All Service
Terminal Interface screens appear in Appendix A - Service Terminal Interface.
Table 20 Valid characters for data entry
Alphanumeric Special characters
A-Z, 0-9 space [ ] ^ _ ! " # $ % & ( ) * + - / , . ; < = > @
NOTE
If an alarm occurs while a user is logged on, the LCD backlight will flash and the audible
alarm will sound. To obtain specific information about the alarm, you must access the Active
Alarm screen (see 7.1 - View Active Alarms) or the Alarm Log (see 7.2 - View Alarm Log).
NOTE
If, after logging in, you press the ESC key to return to a previous screen that is not password-
protected, you must log in again, including entering your password if you wish to access
password-protected functions.
Main Menu
VIEW STATUS
> SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
Login
LOGIN
AAAA
↑↓=SELECT ↵=NEXT/END
System & Control Menu
> SETUP SYSTEM
MANUAL OUTPUT CTRL
CLEAR ALARMS & LOGS
↑↓=NEXT ↵=SELECT
System and Control Options
44
Figure 14 shows the main options available from the System & Control menu.
Figure 14 Menu overview - System and Control menu
Opening Screen
UNIVERSAL MONITOR
DD-MON-YY HR:MM:SS
VX.XXX.X
PRESS ↵=STATUS/SETUP
Main Menu
VIEW STATUS
> SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
Login Screen
LOGIN
AAAA
↑↓=SELECT ↵=NEXT/END
System & Control menu
Setup System selected
System & Control menu
Manual Output Ctrl selected
System & Control menu
Clear Alarms&Logs selected
> SETUP SYSTEM
MANUAL OUTPUT CTRL
CLEAR ALARMS & LOGS
SETUP SYSTEM
> MANUAL OUTPUT CTRL
CLEAR ALARMS & LOGS
SETUP SYSTEM
MANUAL OUTPUT CTRL
> CLEAR ALARMS & LOGS
Setup System menu Select Output Clear Alarms/Logs menu
SETUP INPUT
SETUP COMMON ALARM
SETUP SENSOR
SETUP I/O MATRIX
SETUP OUTPUT
SETUP MODEM&PAGERS
SETUP SYSTEM INFO
SETUP EXP BOARD
See
Section
9.2
OVERRIDE OUTPUT
> OUTPUT01 AUTO
OUTPUT02 AUTO
.
.
.
OUTPUT16 AUTO
See
Section
9.11
CLEAR ACTIVE ALARMS
CLEAR ALARM LOG
CLEAR EVENT LOG
CLEAR TREND LOGS
See
Section
9.12
Override Output
SELECT OUTPUT01
AUTO
CLEAR ACTIVE ALARMS
ARE YOU SURE? N
CLEAR ALARM LOG
ARE YOU SURE? N
CLEAR EVENT LOG
ARE YOU SURE? N
CLEAR TREND LOGS
ARE YOU SURE? N
Setup Input Setup Common Alarm Setup Sensor Setup I/O Matrix
SELECT INPUT
> INPUT_01 NO-AL-NL
INPUT_02 NO-AL-NL
.
.
.
INPUT_24 NO-AL-NL
See
Section
9.3
RESET COMMON ALARM
WITH SILENCE? N
See
Section
9.4
SELECT SENSOR
> SENSOR_1 +80.00 DEG
.
.
.
SENSOR_4 +79.50 RH
See
Section
9.5
MAP INPUT TO OUTPUT
MAP SENSOR TO OUTPT
See
Section
9.6
SETUP INPUT_01
LABEL: INPUT_01
NORM OPEN/CLOSE: NO
ALARM/EVENT: AL
LATCHED: N
DELAY: 00:01
SETUP SENSOR_1
CONNECTED : N
LABEL: SENSOR_1
UNITS: ___
4 mA: -999.9
20 mA: +999.9
OFFSET: +000.0
ALARM/EVENT: AL
LATCHED: N
LOW SETPT: -950.0
HIGH SETPT: +950.0
SENSOR DELAY: 00:01
Setup Output Setup Modem & Pagers
SELECT OUTPUT
> OUTPUT01 NO
OUTPUT02 NO
.
.
.
OUTPUT16 NO
See
Section
9.7
SETUP PAGERS
SETUP MODEM
See
Section
9.8
Setup System Info Setup Exp Board
CHANGE PASSWORD
CHANGE DATE & TIME
SETUP SITE ID
CONNECT BATTERY
SETUP SERV PH NUM
FACTORY DEFAULTS
See
Section
9.9
IS THE EXPANSION
BOARD CONNECTED? N
↑↓=Y/N ↵=END
See
Section
9.10
CHANGE LABEL
CHANGE STATE
SELECT PAGER
PAGER NUMBER 1
.
.
.
PAGER NUMBER 4
ENTER INIT STRING
ATS0=1
See Figure 15 for details
on Setup System Info
SET PAGER 1 NUMBER
SET PAGER 1 PIN
Setup System options
SELECT INPUT
INPUT_01
INPUT_02
.
.
.
INPUT_24
SELECT SENSOR
SENSOR_1 HIGH STPT
SENSOR_1 LOW STPT
.
.
.
SENSOR_4 LOW STPT
SELECT OUTPUTS
MAP TO MAIN BOARD
MAP TO EXP BOARD
SELECT OUTPUTS
MAP TO MAIN BOARD
MAP TO EXP BOARD
1 OUTPUT MAP
1 2 3 4 5 6 7 8
YNNNNNNN
1H OUTPUT MAP
1 2 3 4 5 6 7 8
Y N N N N N N N
or or
1 OUTPUT MAP
0910111213141516
NNNNNNNN
1H OUTPUT MAP
0910111213141516
N N N N N N N N
System and Control Options
45
9.2 Setup System - Overview
The Setup System screen displays seven options that allow you to configure input and output
devices and their relationships, the common alarm, the modem, pagers to be dialed when alarms
occur, and a variety of system details, such as login password and system date and time:
• Setup Input
• Setup Common Alarm
• Setup Sensor
•Setup I/O Matrix
• Setup Output
• Setup Modem & Pagers
• Setup System Info
• Setup Exp Board
9.3 Setup System - Setup Input
The Universal Monitor has eight digital input points that may be
configured individually. If the optional Expansion Board is used, an
additional 16 digital inputs may also be configured. These inputs may
have a wide variety of Liebert or other manufacturers’ equipment
connected for monitoring.
To configure a digital input:
Log In and Choose Setup System
• From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
• Enter your password at the Login screen.
• From the System and Control Menu, use the arrows ↑↓ to choose
Setup System, then press Enter ↵.
Select a Digital Input to Configure
• From the Setup System Menu, shown at right, use the arrows ↑↓ to
choose Setup Input and press Enter ↵.
• From the Select Input Menu, choose the input you want—for exam-
ple, Input_01—and press Enter ↵.
Table 21 shows the digital input features you may change, along with
the default settings: you may change the name of the input, define it as
normally open or closed, and specify it as alarmable or as an event.
• Alarmable inputs may be defined as either Unlatched or Latched.
• Event status allows you to monitor a digital input’s state—and use a change in state to initiate an
action through an output, if desired—without triggering an alarm. Events are always Unlatched.
• You may also specify a time delay before the Universal Monitor responds to an alarm or event.
Use the steps following Table 21 to change the default settings for any digital input.
Table 21 Default settings - digital inputs
Feature Default Other Options
LABEL INPUT_01 Any name (up to eight characters)
NORM OPEN/CLOSE NO (Normally open) NC (Normally closed)
ALARM/EVENT AL (Alarmable) EV (Event)
LATCHED NL (Unlatched) / N (No)* L (Latched) / Y (Yes)*
DELAY 00:01 (1 second) Any time (in minutes and seconds) from 00:00 to 99:59
* NOTE: Different abbreviations are used to designate a digital input as Latched or Unlatched as shown below.
Settings - Select Input Menu
(see Section 9.3)
When configuring an input
(see Section 9.3.4)
Unlatched NL (Not Latched) N (No, not latched)
Latched L (Latched) Y (Yes, latched)
Setup System Menu
> SETUP INPUT
SETUP COMMON ALARM
SETUP SENSOR
SETUP I/O MATRIX
↑↓=NEXT ↵=SELECT
SETUP OUTPUT
SETUP MODEM&PAGERS
SETUP SYSTEM INFO
SETUP EXP BOARD
Select Input Menu
SELECT INPUT
> INPUT_01 NO-AL-NL
INPUT_02 NO-AL-NL
↑↓=NEXT ↵=SELECT
INPUT_03 NO-AL-NL
INPUT_04 NO-AL-NL
INPUT_05 NO-AL-NL
INPUT_06 NO-AL-NL
INPUT_07 NO-AL-NL
INPUT_08 NO-AL-NL
INPUT_09 NO-AL-NL
INPUT_10 NO-AL-NL
INPUT_11 NO-AL-NL
INPUT_12 NO-AL-NL
INPUT_13 NO-AL-NL
INPUT_14 NO-AL-NL
INPUT_15 NO-AL-NL
INPUT_16 NO-AL-NL
INPUT_17 NO-AL-NL
INPUT_18 NO-AL-NL
INPUT_19 NO-AL-NL
INPUT_20 NO-AL-NL
INPUT_21 NO-AL-NL
INPUT_22 NO-AL-NL
INPUT_23 NO-AL-NL
INPUT_24 NO-AL-NL
NOTE: INPUT_09 - INPUT_24
for optional Expansion Board
System and Control Options
46
9.3.1 Change Label (Name of Input)
Each input has a default label (Input_01, Input_02, etc.) that you may
change to a more descriptive name for ease in recognizing alarms and
events associated with the input. The label may consist of up to eight
characters (see Table 20 for valid characters).
• From the Setup Input Menu, choose Label for the selected
input—Label: Input_01 in the example at right—and press
Enter ↵.
• To change the input’s label, which may consist of up to eight char-
acters:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
9.3.2 Define Input as Normally Open or Normally Closed
Each input may be set up as Normally Open (NO) or Normally Closed
(NC). The default setting for all input points is NO (Normally Open).
If you require an input to be a supervised point, define the input as
Normally Closed (NC).
• From the Setup Input Menu, choose Norm Open/Close, as shown
at right, and press Enter ↵.
• To change the normal state for this input, use the arrows ↑↓ to
choose NO (Normally Open) or NC (Normally Closed), then press
Enter ↵.
9.3.3 Define Input as Alarmable or Event
Each digital input may be defined as Alarmable (AL) or as an
Event (EV).
• For a digital input defined as alarmable, the following alarm reac-
tions occur when the status of the monitored input device changes:
the LCD flashes, the audible horn sounds, configured pager num-
bers will be notified and a record is entered in the Alarm Log.
• For a digital input defined as an event, the status change is
recorded in the Event Log.
By default, all digital inputs are set up as AL (Alarmable).
• From the Setup Input Menu, choose Alarm/Event, as shown at
right, and press Enter ↵.
• To change the type of digital input, use the arrows ↑↓ to choose
AL (Alarmable) or EV (Event), then press Enter ↵.
Setup Input Menu
SETUP INPUT_01
> LABEL: INPUT_01
NORM OPEN/CLOSE: NO
ALARM/EVENT: AL
↑↓=NEXT ↵=SELECT
LATCHED: N
DELAY: 00:01
Change Label
CHANGE LABEL
INPUT_01
↑↓=SELECT ↵=NEXT/END
Setup Input Menu
SETUP INPUT_01
LABEL: INPUT_01
> NORM OPEN/CLOSE: NO
ALARM/EVENT: AL
↑↓=NEXT ↵=SELECT
LATCHED: N
DELAY: 00:01
Normally Open / Closed
IS INPUT NORMALLY
OPENED OR CLOSED? NO
↑↓=NO/NC ↵=END
Setup Input Menu
SETUP INPUT_01
LABEL: INPUT_01
NORM OPEN/CLOSE: NO
> ALARM/EVENT: AL
↑↓=NEXT ↵=SELECT
LATCHED: N
DELAY: 00:01
Alarmable / Event
IS INPUT AN ALARM
OR EVENT? AL
↑↓=AL/EV ↵=END
System and Control Options
47
9.3.4 Set Up Alarmable Inputs in Latched or Unlatched Mode
Alarmable input points may be set up in Latched mode (Y), which
requires the user to clear the Universal Monitor alarms after an alarm
has occurred, or Unlatched mode (N), in which alarms will automati-
cally clear after a return-to-normal state. The default setting for
alarmable inputs is N (Unlatched). Any input defined as an event is
automatically Unlatched.
A digital input defined as Latched does not reset automatically after
an alarm. It will remain in the triggered position even after the moni-
tored device returns to normal. After an alarm, the user must manu-
ally reset Latched inputs, as described in 9.12.1 - Clear Active
Alarms. This also means that any digital outputs linked to a Latched
digital input will remain triggered until the input is manually reset.
A digital input defined as Unlatched will automatically track the sta-
tus of the monitored device. No action by the user is required.
• From the Setup Input Menu, choose Latched, as shown above
right, and press Enter ↵.
• To change this feature, use the arrows ↑↓ to choose Y (Yes -
Latched) or N (No - Unlatched), then press Enter ↵.
NOTE: Only alarmable input points may be set up as Latched. If you
attempt to set up an event as Latched, the message shown at right
appears. Press the ESC key to return to the previous screen to con-
tinue configuring the digital input.
The only way to reset latched alarms is by clearing active alarms. This
step is required to return latched points to their normal state. For
details, see 9.12.1 - Clear Active Alarms.
9.3.5 Set Up Delay Time
Each input may be set up with a specified time delay between the
occurrence of an alarm or event—a monitored device changes state—
and any response by the Universal Monitor. This feature can prevent
needless responses to transient conditions.
This delay is the amount of time that must elapse before the Universal
Monitor acknowledges the change of state in the monitored device and
takes any further action, such as dialing configured pagers. The
default time delay is 1 second (displayed as 00 MIN : 01 SEC).
The time delay applies only when a monitored device changes from its
normal state—for example, the Universal Monitor detects a closed
contact that is defined as Normally Open.
When the monitored device returns to its normal state, the Universal
Monitor acknowledges the change of state immediately.
• From the Setup Input Menu, choose Delay, as shown at right, and
press Enter ↵.
• To change the time delay in minutes and seconds (in the range of 00:00 to 99:59):
• For minutes (MIN), press and hold one of the arrow keys ↑↓ scroll through the numbers
00-99.
• Press Enter ↵ to advance to seconds (SEC).
• For seconds (SEC), press and hold one of the arrow keys ↑↓ scroll through the numbers 00-59.
• When finished, press Enter ↵ again.
Setup Input Menu
SETUP INPUT_01
LABEL: INPUT_01
NORM OPEN/CLOSE: NO
ALARM/EVENT: AL
↑↓=NEXT ↵=SELECT
> LATCHED: N
DELAY: 00:01
Latched / Unlatched
IS ALARM
LATCHED? N
↑↓=Y/N ↵=END
Message (if input has
been defined as an event)
LATCH NOT ALLOWED
WHEN IN EVENT MODE
ESC=BACK
Setup Input Menu
SETUP INPUT_01
LABEL: INPUT_01
NORM OPEN/CLOSE: NO
ALARM/EVENT: AL
↑↓=NEXT ↵=SELECT
LATCHED: N
DELAY: 00:01
Delay Time
DELAY TIME BEFORE
TRIGGER?
00 MIN : 01 SEC
↑↓=SELECT ↵=NEXT/END
System and Control Options
48
9.4 Setup System - Setup Common Alarm
The audible alarm sounds after the Universal Monitor detects an alarm condition in any input that
has been defined as alarmable, including digital and analog sensor inputs. Once the alarm is silenced,
there are two options:
• By default, the common alarm remains energized until the input alarm is cleared.
• You may change this setting to de-energize the common alarm automatically once the alarm is
silenced.
You might want to reset the common alarm with silence if an external alarm—for example, a horn—is
connected to the common alarm output contacts.
You might not want to reset the common alarm contacts (let contacts reflect/track alarms) and simply
silence the audible horn.
To change the common alarm setting:
Log In and Choose Setup System
• From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
• Enter your password at the Login screen.
• From the System and Control Menu, use the arrows ↑↓ to choose
Setup System, then press Enter ↵.
Change to Reset (Y) or Not Reset (N)
• From the Setup System Menu, shown at right, use the arrows ↑↓
to choose Setup Common Alarm and press Enter ↵.
• By default, the common alarm is set up not to reset automatically
when the alarm is silenced (N). To change this setting, use the
arrows ↑↓ to choose Y (Yes - reset with silence) or N (No - not
reset), then press Enter ↵.
Setup System Menu
SETUP INPUT
> SETUP COMMON ALARM
SETUP SENSOR
SETUP I/O MATRIX
↑↓=NEXT ↵=SELECT
SETUP OUTPUT
SETUP MODEM&PAGERS
SETUP SYSTEM INFO
SETUP EXP BOARD
Reset Common Alarm
RESET COMMON ALARM
WITH SILENCE? N
↑↓=Y/N ↵=END
System and Control Options
49
9.5 Setup System - Setup Sensor
The Universal Monitor has four analog sensor input points that may be configured individually. The
panel monitors connected equipment for any 4-20 mA input—for example, temperature and humidity.
To configure a sensor:
Log In and Choose Setup System
• From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
• Enter your password at the Login screen.
• From the System and Control Menu, use the arrows ↑↓ to choose
Setup System, then press Enter ↵.
Select a Sensor to Configure
• From the Setup System Menu, shown at right, use the arrows ↑↓
to choose Setup Sensor and press Enter ↵.
• From the Select Sensor Menu, choose the sensor you want—for
example, Sensor_1—and press Enter ↵.
Table 22 shows sensor features that may be changed, along with the
default settings. By default, sensor inputs are not connected.
To activate a sensor input, you must specify it as connected and enter
corresponding values for 4 and 20 mA, as well as high and low set-
points. Other features that may be altered include the name of the sensor, the abbreviation for the
units, and defining the sensor as alarmable or as an event.
• Alarmable sensors may be Latched (Y) or Unlatched (N).
• Event status allows you to monitor a sensor’s high and low setpoints—and use those setpoints to
change the status of an output, if desired—without triggering an alarm. Events are always
Unlatched.
• You may also specify a time delay before the Universal Monitor responds to an alarm or event.
Use the steps following Table 22 to change the default settings for any analog sensor input.
Table 22 Default settings - analog sensor inputs
Feature Default Other Options
CONNECTED* N (Not connected)* Y (Connected)**
LABEL SENSOR_1 Any name (up to eight characters)
UNITS Blank Any units (up to three characters)
4 mA -999.9 Can define up to two decimal places—for example, -99.99
20 mA +999.9 Can define up to two decimal places—for example, +99.99
OFFSET +000.0 Can define up to two decimal places—for example, +00.00
ALARM/EVENT AL (Alarmable) EV (Event)
LATCHED N (Unlatched) Y (Latched)
LOW SETPT -0999.9 Can define up to two decimal places—for example, -999.99
HIGH SETPT +0999.9 Can define up to two decimal places—for example, +999.99
SENSOR DELAY 00:01 (1 second) Any time (in minutes and seconds) from 00:00 to 99:59
* If a sensor is configured as N (Not connected), the display will show an empty reading (blank spaces).
** If a sensor is configured as Y (Connected) and is functioning properly, the display will show a reading. If the
connected sensor is not functioning properly, the display will show dashes (------) indicating a problem.
Setup System Menu
SETUP INPUT
SETUP COMMON ALARM
> SETUP SENSOR
SETUP I/O MATRIX
↑↓=NEXT ↵=SELECT
SETUP OUTPUT
SETUP MODEM&PAGERS
SETUP SYSTEM INFO
SETUP EXP BOARD
Select Sensor Menu
SELECT SENSOR
> SENSOR_1 +80.00 DEG
SENSOR_2 ------ DEG
↑↓=NEXT ↵=SELECT
SENSOR_3
SENSOR_4 +79.50 RH
System and Control Options
50
9.5.1 Identify the Sensor as Connected
To make use of an analog sensor, you must specify it as Connected (Y).
By default, analog sensors are Not connected (N).
• From the Setup Sensor Menu, choose Connected, as shown at
right, and press Enter ↵.
• To change this feature, use the arrows ↑↓ to choose Y (Yes - Con-
nected) or N (No - Not connected), then press Enter ↵.
9.5.2 Change Sensor Label (Name)
Each sensor has a default label (Sensor_1, Sensor_2, etc.) that you may
change to a more descriptive name. The label may consist of up to eight
characters (see Table 20 for valid characters).
• From the Setup Sensor Menu, choose Label for the selected sen-
sor—Label: Sensor_1 in the example—and press Enter ↵.
• To change the sensor’s label, which may consist of up to eight char-
acters:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
9.5.3 Change Units Label
For each sensor, you may use a three-character label to specify mea-
surement units, such as DEG (see Table 20 for valid characters).
• From the Setup Sensor Menu, choose Units for the selected sensor
and press Enter ↵.
• To enter the units label, which may consist of up to three charac-
ters:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
Setup Sensor Menu
SETUP SENSOR_1
> CONNECTED : N
LABEL: SENSOR_1
↑↓=NEXT ↵=SELECT
UNITS: ___
4 mA: -999.9
20 mA: +999.9
OFFSET: +000.0
ALARM/EVENT: AL
LATCHED: N
LOW SETPT: -0999.9
HIGH SETPT: +0999.9
SENSOR DELAY: 00:01
Sensor Connected
IS THE SENSOR
CONNECTED? N
↑↓=Y/N ↵=END
Setup Sensor Menu
SETUP SENSOR_1
CONNECTED : Y
> LABEL: SENSOR_1
↑↓=NEXT ↵=SELECT
UNITS: ___
4 mA: -999.9
20 mA: +999.9
OFFSET: +000.0
ALARM/EVENT: AL
LATCHED: N
LOW SETPT: -0999.9
HIGH SETPT: +0999.9
SENSOR DELAY: 00:01
Change Sensor Label
CHANGE SENSOR LABEL
LABEL: ROOM TMP
↑↓=SELECT ↵=END
Setup Sensor Menu
SETUP SENSOR_1
CONNECTED : Y
LABEL: ROOM_TMP
↑↓=NEXT ↵=SELECT
> UNITS: ___
4 mA: -999.9
20 mA: +999.9
OFFSET: +000.0
ALARM/EVENT: AL
LATCHED: N
LOW SETPT: -0999.9
HIGH SETPT: +0999.9
SENSOR DELAY: 00:01
Change Units Label
CHANGE UNITS LABEL
UNITS: DEG
↑↓=SELECT ↵=NEXT/END
System and Control Options
51
9.5.4 Change 4 mA Value
For the 4 mA value, enter the smallest value for the range of the sen-
sor—for example, 50°F for a temperature sensor with a range of 50°F
to 90°F.
The default value for each sensor is -999.9. Values that can be entered
range from -999.9 to +999.9.
To enter a new value:
• From the Setup Sensor Menu, choose 4mA for the selected sensor
and press Enter ↵.
• To change the 4 mA value:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
9.5.5 Change 20 mA Value
For the 20 mA value, enter the largest value for the range of the sen-
sor—for example, 90°F for a temperature sensor with a range of 50°F
to 90°F.
The default value for each sensor is +999.9. Values that can be entered
range from -999.9 to +999.9.
To enter a new value:
• From the Setup Sensor Menu, choose 20 mA for the selected sen-
sor and press Enter ↵.
• To change the 20 mA value:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
9.5.6 Change Offset Value
For the Offset value, enter an adjustment factor—for example, if the
sensor reading shows 70°F when the actual temperature is 75°F, the
offset might be 5°F.
The default Offset value for each sensor is +000.0. Values that can be
entered range from -999.9 to +999.9.
To enter a new value:
• From the Setup Sensor Menu, choose Offset for the selected sensor
and press Enter ↵.
• To change the Offset value:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
Setup Sensor Menu
SETUP SENSOR_1
CONNECTED : Y
LABEL: ROOM_TMP
↑↓=NEXT ↵=SELECT
UNITS: DEG
> 4 mA: -999.9
20 mA: +999.9
OFFSET: +000.0
ALARM/EVENT: AL
LATCHED: N
LOW SETPT: -0999.9
HIGH SETPT: +0999.9
SENSOR DELAY: 00:01
Change 4 mA Value
CHANGE 4 mA VALUE
4 mA: +050.0
↑↓=SELECT ↵=NEXT/END
Setup Sensor Menu
SETUP SENSOR_1
CONNECTED : Y
LABEL: ROOM_TMP
↑↓=NEXT ↵=SELECT
UNITS: DEG
4 mA: +050.0
> 20 mA: +999.9
OFFSET: +000.0
ALARM/EVENT: AL
LATCHED: N
LOW SETPT: -0999.9
HIGH SETPT: +0999.9
SENSOR DELAY: 00:01
Change 20 mA Value
CHANGE 20 mA VALUE
20 mA: +090.0
↑↓=SELECT ↵=NEXT/END
Setup Sensor Menu
SETUP SENSOR_1
CONNECTED : Y
LABEL: ROOM_TMP
↑↓=NEXT ↵=SELECT
UNITS: DEG
4 mA: +050.0
20 mA: +090.0
> OFFSET: +000.0
ALARM/EVENT: AL
LATCHED: N
LOW SETPT: -0999.9
HIGH SETPT: +0999.9
SENSOR DELAY: 00:01
Change Offset Value
CHANGE OFFSET VALUE
OFFSET: +005.0
↑↓=SELECT ↵=NEXT/END
System and Control Options
52
9.5.7 Define Sensor as Alarmable or Event
Each sensor may be defined as Alarmable (AL) or as an Event (EV).
• For a sensor defined as alarmable, the following alarm reactions
occur when the high-setpoint threshold is crossed: the LCD flashes,
the audible horn sounds, configured pager numbers will be notified
and a record is entered in the Alarm Log.
• For a sensor defined as an event, the high-setpoint occurrence is
recorded in the Event Log.
By default, all sensors are set up as AL (Alarmable).
• From the Setup Sensor Menu, choose Alarm/Event, as shown at
right, and press Enter ↵.
• To change the type of sensor, use the arrows ↑↓ to choose
AL (Alarmable) or EV (Event), then press Enter ↵.
9.5.8 Set Up Alarmable Sensors in Latched or Unlatched Mode
Alarmable sensor points may be set up in Latched mode (Y), requiring
the user to clear the Universal Monitor alarms after an alarm has
occurred, or Unlatched mode (N), meaning that alarms will automati-
cally clear after a return-to-normal state. The default setting for
alarmable sensors is N (Unlatched). Any sensor defined as an event is
automatically Unlatched.
A sensor defined as Latched does not reset automatically after an
alarm. It will remain in the triggered position even after the monitored
sensor returns to normal. After an alarm, the user must manually
reset Latched sensors, as described in 9.12.1 - Clear Active Alarms.
This also means that any digital outputs linked to a Latched sensor
will remain triggered until the sensor is manually reset.
A sensor defined as Unlatched will automatically track the status of
the monitored sensor. No action by the user is required.
• From the Setup Sensor Menu, choose Latched, as shown at right,
and press Enter ↵.
• To change this feature, use the arrows ↑↓ to choose Y (Yes -
Latched) or N (No - Unlatched), then press Enter ↵.
NOTE: Only alarmable sensors may be set up as Latched. If you
attempt to set up an event as Latched, the message shown at right
appears. Press the ESC key to return to the previous screen to con-
tinue configuring the digital input.
The only way to reset latched alarms is by clearing active alarms. This
step is required to return latched points to their normal state. For
details, see 9.12.1 - Clear Active Alarms.
Setup Sensor Menu
SETUP SENSOR_1
CONNECTED : Y
LABEL: ROOM_TMP
↑↓=NEXT ↵=SELECT
UNITS: DEG
4 mA: +050.0
20 mA: +090.0
OFFSET: +005.0
> ALARM/EVENT: AL
LATCHED: N
LOW SETPT: -0999.9
HIGH SETPT: +0999.9
SENSOR DELAY: 00:01
Alarmable / Event
IS SENSOR AN ALARM
OR EVENT? AL
↑↓=AL/EV ↵=END
Setup Sensor Menu
SETUP SENSOR_1
CONNECTED : Y
LABEL: ROOM_TMP
↑↓=NEXT ↵=SELECT
UNITS: DEG
4 mA: +050.0
20 mA: +090.0
OFFSET: +005.0
ALARM/EVENT: AL
> LATCHED: N
LOW SETPT: -0999.9
HIGH SETPT: +0999.9
SENSOR DELAY: 00:01
Latched / Unlatched
IS ALARM
LATCHED? N
↑↓=Y/N ↵=END
Message (if sensor has
been defined as an event)
LATCH NOT ALLOWED
WHEN IN EVENT MODE
ESC=BACK
System and Control Options
53
9.5.9 Change Low Setpoint
The Low Setpoint value is typically above the 4 mA value for the sen-
sor. For example, if the 4 mA value is 50°F, the Low Setpoint might be
60°F. When the sensor crosses below this value, an alarm or event will
occur, depending on the sensor configuration.
The default Low Setpoint for each sensor is -950.0. Values that can be
entered range from:
• the 4 mA value + the Offset value (in the example, 50+5=55)
to
• the 20 mA value + the Offset value (in the example, 90+5=95)
To determine these values, see 9.5.4 - Change 4 mA Value, 9.5.5 -
Change 20 mA Value and 9.5.6 - Change Offset Value.
To enter a new value:
• From the Setup Sensor Menu, choose Low Setpt for the selected
sensor and press Enter ↵.
• To change the Low Setpoint:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
9.5.10 Change High Setpoint
The High Setpoint value is typically below the 20 mA value for the sen-
sor. For example, if the 20 mA value is 90°F, the High Setpoint might
be 85°F. When the sensor crosses above this value, an alarm or event
will occur, depending on the sensor configuration.
The default High Setpoint for each sensor is +950.0. Values that can be
entered range from:
• the 4 mA value + the Offset value (in the example, 50+5=55)
to
• the 20 mA value + the Offset value (in the example, 90+5=95)
To determine these values, see 9.5.4 - Change 4 mA Value, 9.5.5 -
Change 20 mA Value and 9.5.6 - Change Offset Value.
To enter a new value:
• From the Setup Sensor Menu, choose High Setpt for the selected
sensor and press Enter ↵.
•To change the High Setpoint:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
Setup Sensor Menu
SETUP SENSOR_1
CONNECTED : Y
LABEL: ROOM_TMP
↑↓=NEXT ↵=SELECT
UNITS: DEG
4 mA: +050.0
20 mA: +090.0
OFFSET: +005.0
ALARM/EVENT: AL
LATCHED: N
> LOW SETPT: +0055.0
HIGH SETPT: +0999.9
SENSOR DELAY: 00:01
Change Low Setpoint
CHANGE LOW SETPOINT
LOW SETPT: +0060.0
↑↓=SELECT ↵=NEXT/END
Setup Sensor Menu
SETUP SENSOR_1
CONNECTED : Y
LABEL: ROOM_TMP
↑↓=NEXT ↵=SELECT
UNITS: DEG
4 mA: +050.0
20 mA: +090.0
OFFSET: +005.0
ALARM/EVENT: AL
LATCHED: N
LOW SETPT: +0060.0
> HIGH SETPT: +0095.0
SENSOR DELAY: 00:01
Change High Setpoint
CHANGE HIGH SETPOINT
HIGH SETPT: +0085.0
↑↓=SELECT ↵=NEXT/END
System and Control Options
54
9.5.11 Set Up Delay Time
Each sensor may be set up with a specified time delay between the
triggering of a high or low setpoint—a monitored sensor crosses the
high or low setpoint threshold—and any response by the Universal
Monitor. This feature can prevent transient conditions from prompting
unnecessary responses.
This delay is the amount of time that must elapse before the Universal
Monitor acknowledges the change in the monitored sensor and takes
any further action, such as dialing configured pagers. The default time
delay is 1 second (displayed as 00 MIN : 01 SEC).
The time delay applies to the triggering of a high or low setpoint and
also after the monitored sensor returns to its normal state. When the
monitored device returns to its normal state, the specified time delay
must elapse before the Universal Monitor acknowledges the return-to-
normal condition.
• From the Setup Sensor Menu, choose Sensor Delay, as shown at
right, and press Enter ↵.
• To change the time delay in minutes and seconds (in the range of
00:00 to 99:59):
• For minutes (MIN), press and hold one of the arrow keys ↑↓ scroll through the numbers
00-99.
• Press Enter ↵ to advance to seconds (SEC).
• For seconds (SEC), press and hold one of the arrow keys ↑↓ scroll through the numbers 00-59.
Setup Sensor Menu
SETUP SENSOR_1
CONNECTED : Y
LABEL: ROOM_TMP
↑↓=NEXT ↵=SELECT
UNITS: DEG
4 mA: +050.0
20 mA: +090.0
OFFSET: +005.0
ALARM/EVENT: AL
LATCHED: N
LOW SETPT: +055.00
HIGH SETPT: +085.00
SENSOR DELAY: 00:01
Delay Time
DELAY TIME BEFORE
TRIGGER?
00 MIN : 01 SEC
↑↓=SELECT ↵=NEXT/END
System and Control Options
55
9.6 Setup System - Setup I/O Matrix
The Setup I/O Matrix menu allows you to configure the Universal Monitor’s digital and analog inputs
to trigger various actions in any or all of the 16 outputs—eight on the main board and another eight if
the optional Expansion Board is used. Each output can be set up to respond to more than one digital
or analog input, including the additional 16 inputs available via the optional Expansion Board.
Almost any mapping combination can be used. For example, you may
decide to trigger an action in Output03 when Input_01 goes into alarm,
or you might want to generate an action in Output04 when Sensor_1
High Setpoint goes into alarm.
To set up the mapping of inputs to outputs:
Log In and Choose Setup System
• From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
• Enter your password at the Login screen.
• From the System and Control Menu, use the arrows ↑↓ to choose
Setup System, then press Enter ↵.
Select Setup I/O Matrix
• From the Setup System Menu, shown at right, use the arrows ↑↓ to
choose Setup I/O Matrix and press Enter ↵.
• Use the following instructions to set up the mapping of each digital
input or analog sensor input to each output.
9.6.1 Set Up Mapping for a Digital Input
• Use the arrows ↑↓ to choose Map Input To Output from the Map
Input/Sensor Menu, and press Enter ↵.
• From the Select Input Menu, choose the input you want—for exam-
ple, Input_01—and press Enter ↵.
Map Input to a Main Board Output
• From the Select Outputs menu, select Map to Main Board if you
want to map the selected input to an output on the Universal Mon-
itor’s main board. These outputs are identified as Outputs 1-8.
• On the Output Map screen, you may map the selected input to any
of the eight outputs (1-8)—or to more than one output, if desired.
The example at right shows Input_01 mapped to Output03.
To make changes to the mapping:
• If needed, press Enter ↵ to advance to the position directly
below the output.
• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or
N(No - Not mapped), then press Enter ↵.
• Press Enter ↵ to advance to the next position where you want
to make a change.
• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or
N(No - Not mapped), then press Enter ↵.
• When finished, press Enter ↵ again.
Setup System Menu
SETUP INPUT
SETUP COMMON ALARM
SETUP SENSOR
> SETUP I/O MATRIX
↑↓=NEXT ↵=SELECT
SETUP OUTPUT
SETUP MODEM&PAGERS
SETUP SYSTEM INFO
SETUP EXP BOARD
Map Input/Sensor Menu
> MAP INPUT TO OUTPUT
MAP SENSOR TO OUTPT
↑↓=NEXT ↵=SELECT
Select Input
SELECT INPUT
> INPUT_01
INPUT_02
↑↓=NEXT ↵=SELECT
INPUT_03
INPUT_04
INPUT_05
INPUT_06
INPUT_07
INPUT_08
INPUT_09
INPUT_10
INPUT_11
INPUT_12
INPUT_13
INPUT_14
INPUT_15
INPUT_16
INPUT_17
INPUT_18
INPUT_19
INPUT_20
INPUT_21
INPUT_22
INPUT_23
INPUT_24
Select Outputs
SELECT OUTPUTS
> MAP TO MAIN BOARD
MAP TO EXP BOARD
↑↓=NEXT ↵=SELECT
Output Map
1 OUTPUT MAP
1 2 3 4 5 6 7 8
NNYNNNNN
↑↓=Y/N ↵=NEXT/END
System and Control Options
56
Map Input to Expansion Board Output
• From the Select Outputs menu, select Map to Exp Board if you
want to map the selected input to an output on the optional Expan-
sion Board. These outputs are identified as Outputs 9-16.
• On the Output Map screen, you may map the selected input to any
of the eight outputs (9-16)—or to more than one output, if desired.
The example at right shows Input_01 mapped to Output10.
To make changes to the mapping:
• If needed, press Enter ↵ to advance to the position directly
below the output.
• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or
N(No - Not mapped), then press Enter ↵.
• Press Enter ↵ to advance to the next position where you want
to make a change.
• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or N(No - Not mapped), then
press Enter ↵.
• When finished, press Enter ↵ again.
Default Mappings - Digital Inputs to Outputs
Table 23 shows the default mapping of digital inputs to digital outputs.
Table 23 Default mapping of digital inputs to digital outputs
Digital input By default, mapped to digital output:
Input_01 Output01
Input_02 Output02
Input_03 Output03
Input_04 Output04
Input_05 Output05
Input_06 Output06
Input_07 Output07
Input_08 Output08
NOTE: By default, no Expansion Board inputs are mapped to any outputs.
Select Outputs
SELECT OUTPUTS
MAP TO MAIN BOARD
> MAP TO EXP BOARD
↑↓=NEXT ↵=SELECT
Output Map
1 OUTPUT MAP
0910111213141516
NYNNNNNN
↑↓=Y/N ↵=NEXT/END
System and Control Options
57
9.6.2 Set Up Mapping for an Analog Sensor Input
• Use the arrows ↑↓ to choose Map Sensor To Outpt from the Map
Input/Sensor Menu, and press Enter ↵.
• From the Select Sensor Menu, choose the input you want—for
example, Sensor_1 High Stpt—and press Enter ↵.
Map Sensor to Main Board Output
• From the Select Outputs menu, select Map to Main Board if you
want to map the selected sensor to an output on the Universal
Monitor main board. These outputs are identified as Outputs 1-8.
• On the Output Map screen, you may map the selected sensor to any
of the eight outputs (1-8)—or to more than one output, if desired.
The example at right shows Sensor_1 High Stpt mapped to
Output04.
To make changes to the mapping:
• If needed, press Enter ↵ to advance to the position directly
below the output.
• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or
N(No - Not mapped), then press Enter ↵.
• Press Enter ↵ to advance to the next position where you want
to make a change.
• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or
N(No - Not mapped), then press Enter ↵.
• When finished, press Enter ↵ again.
Map Sensor to Expansion Board Output
• From the Select Outputs menu, select Map to Exp Board if you
want to map the selected sensor to an output on the optional
Expansion Board. These outputs are identified as Outputs 9-16.
• On the Output Map screen, you may map the selected sensor to any
of the eight outputs (9-16)—or to more than one output, if desired.
The example at right shows Sensor_1 High Stpt mapped to
Output11.
To make changes to the mapping:
• If needed, press Enter ↵ to advance to the position directly
below the output.
• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or
N(No - Not mapped), then press Enter ↵.
• Press Enter ↵ to advance to the next position where you want
to make a change.
• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or
N(No - Not mapped), then press Enter ↵.
• When finished, press Enter ↵ again.
Default Mappings - Analog Inputs to Outputs
By default, analog inputs are not mapped to any digital output, as shown in Table 24.
Table 24 Default mapping of analog inputs to digital outputs
Analog input By default, mapped to digital output:
Sensor_1 (none)
Sensor_2 (none)
Sensor_3 (none)
Sensor_4 (none)
Map Input/Sensor Menu
MAP INPUT TO OUTPUT
> MAP SENSOR TO OUTPT
↑↓=NEXT ↵=SELECT
Select Sensor
SELECT SENSOR
> SENSOR_1 HIGH STPT
SENSOR_1 LOW STPT
↑↓=NEXT ↵=SELECT
SENSOR_2 HIGH STPT
SENSOR_2 LOW STPT
SENSOR_3 HIGH STPT
SENSOR_3 LOW STPT
SENSOR_4 HIGH STPT
SENSOR_4 LOW STPT
Select Outputs
SELECT OUTPUTS
> MAP TO MAIN BOARD
MAP TO EXP BOARD
↑↓=NEXT ↵=SELECT
Output Map
1H OUTPUT MAP
1 2 3 4 5 6 7 8
NNNYNNNN
↑↓=Y/N ↵=NEXT/END
Select Outputs
SELECT OUTPUTS
MAP TO MAIN BOARD
> MAP TO EXP BOARD
↑↓=NEXT ↵=SELECT
Output Map
1H OUTPUT MAP
0910111213141516
NNYNNNNN
↑↓=Y/N ↵=NEXT/END
System and Control Options
58
9.7 Setup System - Setup Output
The Universal Monitor has eight outputs that may be configured indi-
vidually. If the optional Expansion Board is used, its additional eight
digital outputs may be renamed. The outputs may have a wide variety
of Liebert or other manufacturers’ equipment connected for configured
responses to input alarms and events.
To configure an output:
Log In and Choose Setup System
• From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
• Enter your password at the Login screen.
• From the System and Control Menu, use the arrows ↑↓ to choose
Setup System, then press Enter ↵.
Select an Output to Configure
• From the Setup System Menu, shown at right, use the arrows ↑↓
to choose Setup Output and press Enter ↵.
• From the Select Output Menu, choose the output you want—for
example, Output01—and press Enter ↵.
Table 25 shows digital output features and default settings. You may
change the name of any output. In addition, the Universal Monitor’s
eight outputs may be defined as normally open or closed.
Use the steps following Table 25 to change the default settings for any
digital output.
9.7.1 Change Label (Name of Output)
Each output has a default label (Output01, Output02, etc.) that you
may change to a more descriptive name. The label may consist of up to
eight characters (see Table 20 for valid characters).
• From the Setup Output Menu, as shown at right, use the
arrows ↑↓ to choose Change Label for the selected output and
press Enter ↵.
• To change the output’s label, which may consist of up to eight char-
acters:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
9.7.2 Define Main Board Output as Normally Open / Closed
Each output may be set up as Normally Open (NO) or Normally Closed
(NC). The default setting for all output points is NO (Normally Open).
• From the Setup Output Menu, choose Change State, as shown at
right, and press Enter ↵.
• To change the normal state for this output, use the arrows ↑↓ to
choose NO (Normally Open) or NC (Normally Closed), then press
Enter ↵.
Table 25 Default settings - digital outputs
Feature Default Other Options
LABEL OUTPUT01 Any name (up to eight
characters)
NORM OPEN/CLOSE
(Main board only) NO (Normally open) NC (Normally closed)
Setup System Menu
SETUP INPUT
SETUP COMMON ALARM
SETUP SENSOR
SETUP I/O MATRIX
↑↓=NEXT ↵=SELECT
> SETUP OUTPUT
SETUP MODEM&PAGERS
SETUP SYSTEM INFO
SETUP EXP BOARD
Select Output Menu
SELECT OUTPUT
> OUTPUT01 NO
OUTPUT02 NO
↑↓=NEXT ↵=SELECT
OUTPUT03 NO
OUTPUT04 NO
OUTPUT05 NO
OUTPUT06 NO
OUTPUT07 NO
OUTPUT08 NO
OUTPUT09 NO
OUTPUT10 NO
OUTPUT11 NO
OUTPUT12 NO
OUTPUT13 NO
OUTPUT14 NO
OUTPUT15 NO
OUTPUT16 NO
NOTE: OUTPUT09-OUTPUT16
for optional Expansion Board
Setup Output Menu
> CHANGE LABEL
CHANGE STATE
↑↓=NEXT ↵=SELECT
Change Label
CHANGE LABEL
LABEL: OUTPUT01
↑↓=SELECT ↵=NEXT/END
Setup Output Menu
CHANGE LABEL
> CHANGE STATE
↑↓=NEXT ↵=SELECT
Change State
SET TO NORMAL OPEN
OR NORMAL CLOSE? NO
↑↓=NO/NC ↵=END
System and Control Options
59
9.7.3 Set Expansion Board Output by DIP Switch
If you choose Change State from the Setup Output Menu for an
Expansion Board output (OUTPUT09-16), the screen displays a mes-
sage that the state must be set by DIP switch, as shown at right.
Each digital output on the optional Expansion Board has an associated
DIP switch that can determine its operation in the event of loss of com-
munication with the Universal Monitor or loss of power.
To configure a digital output jumper for a loss of power:
• Move the switch down to the “OFF” position (factory default) for
Normally Open (NO).
• Move the switch up to the “ON” position for Normally Closed (NC).
For more information, see 5.2.3 - Setting the Digital Output DIP Switches.
9.7.4 Configure Main Board Output for Loss of Power (“Fail-Safe”)
Each digital output has an associated jumper that can help prevent undesired effects when the con-
troller board loses power. For example, without the proper fail-safe jumper setting, a loss of power
might close a switch that is Normally Open (NO)—perhaps shutting off a fan or closing a valve.
This fail-safe jumper setting is unrelated to configuring an output as Normally Open (NO) or Nor-
mally Closed (NC), as described in the previous section, Define Main Board Output as Normally
Open / Closed.
To configure a digital output jumper for a loss of power:
• Set the jumper in the “OFF” position (factory default) to make the output Normally Open (NO).
• Set the jumper in the “ON” position to make the output Normally Closed (NC).
For more information, see 4.2.3 - Setting the Digital Output Jumpers.
Setup Output Menu
CHANGE LABEL
> CHANGE STATE
↑↓=NEXT ↵=SELECT
Message (if Expansion
Board output selected)
SET BY DIPSWITCH
ESC=BACK
System and Control Options
60
9.8 Setup System - Setup Modem & Pagers
To use the modem and pager features, be sure to connect the phone line connector to a telephone wall
jack using an RJ11 cord, as described in 4.6.2 - Phone Line Connector.
9.8.1 Modem Setup - Initialization String
The Universal Monitor has an on-board modem that offers dial-up access to all LCD functions as well
as features available only through the Service Terminal Interface (see A.1 - Comparison of Func-
tions: LCD and Service Terminal Interface). The modem also permits remote notification of
alarms.
Supported Modem Settings
Supported settings vary for different types of access:
Default Modem Settings
Table 27 shows the default settings for modem options.
Configuring the Modem
To configure the modem:
Log In and Choose Setup System
1. From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
2. Enter your password at the Login screen.
3. From the System and Control Menu, use the arrows ↑↓ to choose
Setup System, then press Enter ↵.
Table 26 Supported modem settings
For: Modem supports:
Dial-up via terminal 9600 baud, no parity, 8 data bits, 1 stop bit
Pager access 9600 baud, even parity, 7 data bits, 1 stop bit and TAPI protocol version 1.8
International
dialing
For calls involving countries that do not support country code B5 (see Table 28):
• Modem model MT5600SMI is required (model number is on the modem label).
•+GCI=xx (xx is the country code) must be added to the initialization string (see Step 7 in
this section).
Table 27 Default settings - modem
Feature Default Other Options
Initialization String (Init String) ATS0=1
Any string (up to 40 characters); for international dialing,
add +GCI=xx, where xx is the country code (except B5
countries—see Table 28)
Enable Modem Diagnostic Messages N (disable) Y (enable)
Modem Dial Prefix ATE0X4DT Any string
Modem Hang Up Delay After a Call 10 seconds Any number (up to 99 seconds)
Setup System Menu
SETUP INPUT
SETUP COMMON ALARM
SETUP SENSOR
SETUP I/O MATRIX
↑↓=NEXT ↵=SELECT
SETUP OUTPUT
> SETUP MODEM&PAGERS
SETUP SYSTEM INFO
SETUP EXP BOARD
System and Control Options
61
Select Modem Setup
4. From the Setup System Menu, shown at right, use the arrows ↑↓ to
choose Setup Modem&Pagers and press Enter ↵.
5. Use the arrows ↑↓ to choose Setup Modem from the Pagers &
Modem Menu and press Enter ↵.
6. The Setup Modem Menu displays the initialization string
(Init String), which may consist of up to 40 characters (see
Table 20 for valid characters). The default Init String is ATS0=1.
International Dialing
7. To enable international dialing involving countries that do not
support country code B5 (see Table 28), you must add the
appropriate country codes to the initialization string using the
format:
+GCI=xx
where xx is the country code.
(This also requires the modem model MT5600SMI; the model num-
ber can be found on the modem label.)
Note: For countries that support B5, there is no need to add coun-
try codes to the init string.
Edit the Init String
8. To enter or edit the Init String:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
Table 28 Country codes
Country Code* Country Code* Country Code* Country Code*
Argentina 07 Finland FD Italy FD Philippines B5
Australia 09 France FD Japan 00 Portugal FD
Austria FD Germany FD Korea B5 Slovak Republic FD
Belgium FD Greece FD Liechtenstein FD Spain FD
Canada B5 Hong Kong 99 Luxembourg FD Sweden FD
China B5 Hungary FD Mexico B5 Switzerland FD
Cyprus FD Iceland FD Netherlands FD Taiwan FE
Czech Republic FD Indonesia 99 New Zealand 7E United Kingdom FD
Denmark FD Ireland FD Norway FD United States B5
* B5 is the default setting—initialization string +GCI=xx is not needed for these countries
Setup System Menu
SETUP INPUT
SETUP COMMON ALARM
SETUP SENSOR
SETUP I/O MATRIX
↑↓=NEXT ↵=SELECT
SETUP OUTPUT
> SETUP MODEM&PAGERS
SETUP SYSTEM INFO
SETUP EXP BOARD
Pagers & Modem Menu
SETUP PAGERS
> SETUP MODEM
↑↓=NEXT ↵=SELECT
Setup Modem Menu
ENTER INIT STRING
ATS0=1
↑↓=NEXT ↵=SELECT
System and Control Options
62
9.8.2 Modem Setup - Additional Features (Service Terminal Interface only)
The Service Terminal Interface offers four additional options for the modem that are not available
through the LCD interface:
• Enter Universal Monitor phone number
• Enable modem diagnostic messages
• Change modem dial prefix
• Change modem hang up delay after a call
To access these options:
• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see
A.2 - Connecting to the Service Terminal Interface).
• At the Main Menu, enter 0 (zero—Setup System-Login Required).
• At the Login Menu, enter your password.
• At the Setup Menu, enter 6 (Setup Modem&Pagers).
• At the Setup Modem & Pagers menu, shown below, enter 5 to begin configuration.
• At the Change Modem Initialization String prompt, you may press Enter to bypass this option (or
see 9.8.1 - Modem Setup - Initialization String for instructions on entering the string).
Enter Universal Monitor Phone Number
This entry allows you to store the phone number that must be dialed to access the Universal Monitor
for future reference. This has no effect on the Universal Monitor’s modem settings or functionality—it
simply places the phone number in an accessible location.
• At the Universal Monitor Phone Number prompt, enter the phone number for the Universal Mon-
itor. The current setting appears in brackets []—nothing has been entered in the following exam-
ple.
• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation mes-
sage appears: “Command Successful.”
Setup Modem & Pagers - Modem Setup (Service Terminal Interface only)
SETUP MODEM&PAGERS
Input pager and
modem information
Select pager or modem
CURRENT NUMBER
*******************
1=PAGER NUMBER 1 An "A" is required
2=PAGER NUMBER 2 as 1st character
3=PAGER NUMBER 3 for an alpha pager,
4=PAGER NUMBER 4 an "N" for a numeric
5=MODEM CONFIGURATION pager, and an "M"
6=RETURN TO SETUP MENU for a remote modem.
7=RETURN TO MAIN MENU *******************
SELECT A NUMBER:5
>CHANGE MODEM INITIALIZATION STRING(40 CHARACTERS MAX).
>[ATS0=1]
>[
>COMMAND SUCCESSFUL
>ENTER UNIVERSAL MONITOR PHONE NUMBER(40 CHARACTERS MAX).
>[]
>[
>COMMAND SUCCESSFUL
System and Control Options
63
Enable Modem Diagnostic Messages
Enabling modem diagnostics will provide the following additional information about the modem to
the computer using the Service Terminal Interface:
• At the Enable Modem Diagnostic Messages prompt, enter Y (Yes - enable) or N (No - disable). The
current setting appears in brackets—[N] in the following example.
• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation mes-
sage appears: “Command Successful.”
Change Modem Dial Prefix
• At the Change Modem Dial Prefix prompt, enter the prefix to be dialed. The current setting
appears in brackets—[ATE0X4DT] in the following example.
• For international dialing involving countries that do not support B5 (see Table 28), add country
codes to the initialization string using the format +GCI=xx, where xx is the country code.
(Note: Also requires MT5600SMI modem; model number is on modem label.)
See 9.8.1 - Modem Setup - Initialization String for more information.
• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation mes-
sage appears: “Command Successful.”
Change Modem Hang Up Delay After a Call
• At the Change Modem Hang Up Delay After a Call prompt, enter the number of seconds to delay
hanging up after a call. The maximum is 99 seconds. The current setting appears in brackets—
[10] in the following example.
• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation mes-
sage appears: “Command Successful.”
Hang-up modem
Modem model number
No dial tone
No carrier
Busy
No answer
Pager checksum error
Pager pin number error
Error (indicates incorrect phone number, dial prefix or modem initialization string)
For alphanumeric pager failures:
Paging company non answer on 1st
Paging company non answer on 2nd
Paging company non answer on Last
Paging company non answer on Handshake
>ENABLE MODEM DIAGNOSTIC MESSAGES-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>CHANGE MODEM DIAL PREFIX.
>[ATE0X4DT]
>[
>COMMAND SUCCESSFUL
>CHANGE MODEM HANG UP DELAY AFTER A CALL(99 SEC MAX).
>[10]
>[
>COMMAND SUCCESSFUL
System and Control Options
64
9.8.3 Pager Setup - Pager Number and PIN
The Universal Monitor may be configured to dial numeric or alphanumeric pagers when an alarm is
detected. You may enter up to four pager numbers—all configured pagers will be dialed each time an
alarm occurs. For each configured pager, you must enter the pager number to be dialed and the
pager’s Personal Identification Number (PIN).
See 10.1 - Universal Monitor Specifications for supported pager settings.
The Universal Monitor can send numeric or alphanumeric messages to supported pagers, as shown in
the following example:
When an alarm is detected, the first pager number is dialed—up to three times, if needed. After a suc-
cessful page or three dialing attempts, the next pager number is dialed, again with three attempts as
needed, and so on for all configured pagers.
To configure a pager:
Log In and Choose Setup System
• From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
• Enter your password at the Login screen.
• From the System and Control Menu, use the arrows ↑↓ to choose
Setup System, then press Enter ↵.
Select a Pager to Configure
• From the Setup System Menu, shown at right, use the arrows ↑↓
to choose Setup Modem&Pagers and press Enter ↵.
• Use the arrows ↑↓ to choose Setup Pagers from the Pagers &
Modem Menu, and press Enter ↵.
• From the Select Pager Menu, choose the pager number you
want—for example, Pager Number 1—and press Enter ↵.
Alphanumeric pager
message example
LIEBERT TEST
INPUT_01 ALARM
CONTACT CLOSED
2:07 PM 06/09/04 Pager company time stamp
Table 29 Pager dialing results
Result of Page Action Message Generated
Successful Universal Monitor dials next configured pager. —
Unsuccessful due to:
Busy signal / no answer /
no dial tone
Universal Monitor generates message after all three
redial attempts have failed, dials next configured pager.
Unsuccessful Page
(Event Log)
General modem
communication problem
Universal Monitor resets modem, generates
message, redials pager up to three more times.
Modem Reset
(Event Log)
No communication with modem
(internal hardware problem)
Universal Monitor generates messages, makes no
further dialing attempts.
Modem Internal Fault
(Active Alarm Report,
Alarm History Log)
Setup System Menu
SETUP INPUT
SETUP COMMON ALARM
SETUP SENSOR
SETUP I/O MATRIX
↑↓=NEXT ↵=SELECT
SETUP OUTPUT
> SETUP MODEM&PAGERS
SETUP SYSTEM INFO
SETUP EXP BOARD
Pagers & Modem Menu
> SETUP PAGERS
SETUP MODEM
↑↓=NEXT ↵=SELECT
Select Pager Menu
SELECT PAGER
> PAGER NUMBER 1
PAGER NUMBER 2
↑↓=NEXT ↵=SELECT
PAGER NUMBER 3
PAGER NUMBER 4
System and Control Options
65
Enter a Pager Number
• From the Setup Pager Menu, choose Setup Pager Number for
the selected pager—Setup Pager 1 Number in the example at
right—and press Enter ↵.
• See Table 30 for guidelines on entering the pager number, which
may consist of up to 40 characters. To enter the pager number:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
Enter a Pager PIN Number
• From the Setup Pager Menu, choose Setup Pager PIN, as shown
for Pager Number 1 in the example at right, and press Enter ↵.
• To enter the pager PIN, which may consist of up to 20 characters
(see Table 20 for valid characters):
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
Table 30 Guidelines for dialing pagers
Device type Required entries Example
Numeric
pager The first character must be “N”. N18005551212
Alphanumeric
pager The first character must be “A”. A18005551212
Remote
modem The first character must be “M”. M18005551212
Device type Optional entries Example
All types
of devices
Use “9” if needed to access an outside
line—place after first character (N, A or M). A918005551212
Use "W" to wait for a second dial tone
before dialing if the phone system has two
dial tones (initial tone and a second tone
for outside line)—place after “9” (before the
number to be dialed).
A9W18005551212
Use “,” (comma) to pause two seconds. N1,8005551212
Numeric
pager
Use “#” as the last character to terminate
page string if required by paging company.
N18005551212
,,,,1234567#
NOTE
For international dialing, you might need to add country codes
in the modem initialization string. See 9.8.1 - Modem Setup -
Initialization String.
Setup Pager Menu
> SET PAGER 1 NUMBER
SET PAGER 1 PIN
↑↓=NEXT ↵=SELECT
Pager # - Numeric
ENTER PAGER 1 NUMBER
N1,8005551212,,,,123
4567#
↑↓=SELECT ↵=NEXT/END
Pager # - Alphanumeric
ENTER PAGER 1 NUMBER
A9W18005551212
↑↓=SELECT ↵=NEXT/END
Setup Pager Menu
SET PAGER 1 NUMBER
> SET PAGER 1 PIN
↑↓=NEXT ↵=SELECT
Enter Pager PIN
ENTER PAGER 1 PIN
01234567891011121314
↑↓=SELECT ↵=NEXT/END
System and Control Options
66
9.8.4 Pager Setup - Communications Check (Service Terminal Interface only)
The Service Terminal Interface offers two additional options for pager setup, which are not available
through the LCD interface:
• Enable communications check
• Enter time to perform communications check
To access these options:
• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see
A.2 - Connecting to the Service Terminal Interface).
• At the Main Menu, enter 0 (zero—Setup System-Login Required).
• At the Login Menu, enter your password.
• At the Setup Menu, enter 6 (Setup Modem&Pagers).
• At the Setup Modem & Pagers menu, shown below, enter a number (1-4) to select a pager.
• At the Enter Pager Number prompt, you may press Enter to bypass this option (or see 9.8.3 -
Pager Setup - Pager Number and PIN for instructions on entering the pager number).
• At the Enter Pager PIN Number prompt, you may press Enter to bypass this option (or see 9.8.3 -
Pager Setup - Pager Number and PIN for instructions on entering the pager PIN).
Setup Modem & Pagers - Pager Setup (Service Terminal Interface only)
SETUP MODEM&PAGERS
Input pager and
modem information
Select pager or modem
CURRENT NUMBER
*******************
1=PAGER NUMBER 1 An "A" is required
2=PAGER NUMBER 2 as 1st character
3=PAGER NUMBER 3 for an alpha pager,
4=PAGER NUMBER 4 an "N" for a numeric
5=MODEM CONFIGURATION pager, and an "M"
6=RETURN TO SETUP MENU for a remote modem.
7=RETURN TO MAIN MENU *******************
SELECT A NUMBER:1
>ENTER PAGER NUMBER(40 CHARACTERS MAX).
>[]
>[
>COMMAND SUCCESSFUL
>ENTER PAGER PIN NUMBER (20 CHARACTERS MAX).
>[]
>[
>COMMAND SUCCESSFUL
System and Control Options
67
Enable Communications Check
Enabling this function permits a daily communications test between the Universal Monitor and the
selected pager. Once each day the Universal Monitor dials the pager at a specified time and sends this
message: “UNIVERSAL MONITOR COMM CHECK.” (The time of the test is specified at the next
prompt, Enter Time To Perform Communications Check.)
• At the Enable Communications Check prompt, enter Y (Yes - enable) or N (No - disable). The cur-
rent setting appears in brackets—[N] in the following example.
• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation mes-
sage appears: “Command Successful.”
Enter Time To Perform Communications Check
This function schedules the daily communications test between the Universal Monitor and the
selected pager, as described in the previous section.
• At the Enter Time To Perform Communications Check prompt, enter the time to initiate the com-
munications check, using the format HH:MM (hours and minutes in military time), ranging from
00:00 for midnight to 23:59 for 11:59 p.m. The current setting appears in brackets—[00:00] in the
following example.
• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation mes-
sage appears: “Command Successful.”
>ENABLE COMMUNICATIONS CHECK-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>ENTER TIME TO PERFORM COMMUNICATIONS CHECK(HH:MM).
>[00:00]
>[
>COMMAND SUCCESSFUL
System and Control Options
68
9.9 Setup System - Setup System Info
The Setup System Info options allow users to:
•Change Password—used for access to system setup functions
•Change Date & Time/Automatic Daylight Saving Time—used to set the Universal Monitor’s
date and time and to enable automatic time change for Daylight Saving Time
•Setup Site ID—the Universal Monitor’s location to differentiate among sites if more than one
Universal Monitor is in use
•Connect Battery—stops the Universal Monitor battery from backing up the panel
•Backup and Upload Configuration File (Service Terminal Interface only)—permits the
user to copy the Universal Monitor’s configuration settings and to upload the file to the Universal
Monitor
•Setup Serv Ph Num—enables alarm notification to the telephone number entered (in addition
to the four pager numbers).
•Restore Defaults—returns the Universal Monitor to its factory settings
•Perform Firmware Update (Service Terminal Interface only)—changes the Universal Mon-
itor’s firmware to newest version
•Initiate Remote Alarm Test (Service Terminal Interface only)—used to test auxiliary
alarm
To change any Setup System Info features:
Log In and Choose Setup System
• From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
• Enter your password at the Login screen.
• From the System and Control Menu, use the arrows ↑↓ to choose
Setup System, then press Enter ↵.
Select Setup System
• From the Setup System Menu, shown at right, use the arrows ↑↓
to choose Setup System Info and press Enter ↵.
• Use the steps following Figure 15 to access any of the Setup Sys-
tem Info options.
Figure 15 offers a quick look at the Setup System Info screens available via the LCD interface.
Figure 15 Menu overview - Setup System Info menu
Setup System Menu
SETUP INPUT
SETUP COMMON ALARM
SETUP SENSOR
SETUP I/O MATRIX
↑↓=NEXT ↵=SELECT
SETUP OUTPUT
SETUP MODEM&PAGERS
> SETUP SYSTEM INFO
SETUP EXP BOARD
Setup System Info
SETUP SYSTEM INFO
CHANGE PASSWORD
CHANGE DATE & TIME
SETUP SITE ID
CONNECT BATTERY
SETUP SERV PH NUM
FACTORY DEFAULTS
Change Password Change Date & Time Setup Site ID
CHANGE PASSWORD
AAAA
See
Section
9.9.1
CHANGE DATE & TIME
DAYLIGHT SVG TIME: Y
18-MAY-02 10:56:30
See
Section
9.9.2
SETUP SITE ID
AAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
See
Section
9.9.3
Connect Battery Setup Serv Ph Num Factory Defaults
IS THE BATTERY
CONNECTED? Y
See
Section
9.9.4
ENTER PHONE NUMBER
9,,18005551212
See
Section
9.9.6
RESTORE ALL DEFAULTS
ARE YOU SURE? N
See
Section
9.9.8
Setup System Info options
System and Control Options
69
9.9.1 Change Password
A password is required to access the Universal Monitor’s system and
control options, as described in 9.1 - Login. The password consists of
four characters (see Table 20 for valid characters). The default pass-
word is AAAA.
Change the Password
To change the password:
• From the Setup System Info Menu, use the arrows ↑↓ to choose
Change Password, then press Enter ↵.
• To change your password:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
Reset Password to the Factory Default (“AAAA”)
To reset the password to the factory default of AAAA:
• Locate DIP switch 1 on the unit’s circuit board (see 1.7 - Controller Board Overview) and move
all switches to the OFF position (down).
• Move the second switch to the ON position, then to the OFF position.
• Move the seventh switch to the ON position, then to the OFF position.
• Move the eighth switch to the ON position, then to the OFF position.
The password should now be AAAA.
9.9.2 Change Date & Time/Automatic Daylight Saving Time
The Universal Monitor has a built-in real-time clock that is backed up by an encapsulated lithium
battery and set up to adjust automatically for daylight saving time twice a year. The Setup System
Info menu allows you to change the date or time or automatic adjustment at any time.
To change the daylight saving time setting, date or time:
• From the Setup System Info Menu, use the arrows ↑↓ to choose
Change Date & Time, then press Enter ↵.
• To change the daylight saving time setting:
• To the right of Daylight Svg Time? use the arrows ↑↓ to
choose Y (Yes - automatically adjust for daylight saving time)
or N (No), then press Enter ↵.
• The format of the date and time is DD-MMM-YY HR:MM:SS. To
change the date or time:
• Press Enter ↵ to advance to the next character position you
want to change.
• Use the arrows ↑↓ to choose from available entries:
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
Date Day (DD) 0-31
Month (MMM) JAN-DEC
Year (YY) 00-99
Time Hour (HR) 00-23
Minutes (MM) 00-59
Seconds (SS) 00-59
Setup System Info Menu
SETUP SYSTEM INFO
> CHANGE PASSWORD
CHANGE DATE & TIME
↑↓=NEXT ↵=SELECT
SETUP SITE ID
CONNECT BATTERY
SETUP SERV PH NUM
FACTORY DEFAULTS
Change Password
CHANGE PASSWORD
AAAA
↑↓=SELECT ↵=NEXT/END
Setup System Info Menu
SETUP SYSTEM INFO
CHANGE PASSWORD
> CHANGE DATE & TIME
↑↓=NEXT ↵=SELECT
SETUP SITE ID
CONNECT BATTERY
SETUP SERV PH NUM
FACTORY DEFAULTS
Change Date & Time
CHANGE DATE & TIME
DAYLIGHT SVG TIME: Y
18-MAY-02 10:56:30
↑↓=SELECT ↵=NEXT/END
System and Control Options
70
9.9.3 Setup Site ID
You may enter a Site ID to identify the Universal Monitor’s location,
using a name that may consist of up to 40 characters (see Table 20 for
valid characters). The Site ID will appear with each alarm.
To enter or change the Site ID:
• From the Setup System Info Menu, use the arrows ↑↓ to choose
Setup Site ID, then press Enter ↵.
• To enter a Site ID:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• If the Site ID is less than 40 characters, you may enter an
underscore (_) character to indicate the end of the name.
• When finished, press Enter ↵ again.
9.9.4 Connect Battery
By default, the Universal Monitor checks the battery and sounds an alarm when the power fails, the
battery runs low or the battery needs to be checked. The battery’s main purpose is to provide enough
power to the modem to notify pagers of a power loss.
Using the following procedure to disconnect the battery will disable battery alarm features only. The
battery itself will continue to provide backup. If battery backup is not desired, the battery must be
unplugged from the circuit board. This can be done by removing the battery leads from the jumpers
(see 2.4.3 - Connecting the Battery Pack).
The default is to connect the battery. However, there may be times that you want to disconnect the
battery so that it does not provide backup.
Table 31 shows battery problems that will affect operation.
To connect or disconnect the battery:
• From the Setup System Info Menu, use the arrows ↑↓ to choose
Connect Battery, then press Enter ↵.
• Use the arrows ↑↓ to choose Y (Yes - the battery is connected) or
N(No - the battery is not connected), then press Enter ↵.
NOTE
The battery will continue to power and provide full operation of the Universal Monitor with the
exception of powering the analog inputs (sensors). The battery will provide backup for a
minimum of 10 minutes.
Table 31 Battery alarms
Result of Battery Action Message Generated
Battery falls below a minimum charge. Battery will not provide battery backup. LOW BATTERY
Battery is connected to the circuit board but
not recognized by the circuit board.
Battery will not provide battery backup. CHECK BATTERY
Battery is unplugged from the circuit board. Battery will not provide battery backup BATTERY UNPLUGGED
Utility power (24VAC) to the circuit board is
too low to power the board.
Universal Monitor board will not be
able to function properly.
LOSS OF POWER
Setup System Info Menu
SETUP SYSTEM INFO
CHANGE PASSWORD
CHANGE DATE & TIME
↑↓=NEXT ↵=SELECT
> SETUP SITE ID
CONNECT BATTERY
SETUP SERV PH NUM
FACTORY DEFAULTS
Setup Site ID
SETUP SITE ID
AAAAAAAAAAAAAAAAAAAA
AAAAAAAAAAAAAAAAAAAA
↑↓=SELECT ↵=NEXT/END
Setup System Info Menu
SETUP SYSTEM INFO
CHANGE PASSWORD
CHANGE DATE & TIME
↑↓=NEXT ↵=SELECT
SETUP SITE ID
> CONNECT BATTERY
SETUP SERV PH NUM
FACTORY DEFAULTS
Connect Battery
IS THE BATTERY
CONNECTED? Y
↑↓=Y/N ↵=END
System and Control Options
71
9.9.5 Backup and Upload Configuration File (Service Terminal Interface only)
This operation may be performed only through the Service Terminal Interface. It permits the user to
make a copy of the Universal Monitor’s configuration settings and save it as a file on the computer
connected through the RS232 port. Should the need arise, the user can upload the configuration file
from the computer to the Universal Monitor, instead of re-entering the settings manually.
To access these options:
1. Connect to the Universal Monitor either from a remote computer or through the RS232 port (see
A.2 - Connecting to the Service Terminal Interface).
2. At the Main Menu, enter 0 (zero—Setup System-Login Required).
3. At the Login Menu, enter your password.
4. At the Setup Menu, enter 7 (Setup System Information).
5. At the Setup System Information Menu, enter 5 (Backup & Upload Configuration File). The
Backup & Upload Configuration File menu appears, shown below:
6. Enter 1 to back up the configuration file from the Universal Monitor to the computer and proceed
to Step 8,
OR
7. Enter 2 to upload the configuration file from the computer to the Universal Monitor and proceed
to Step 13. NOTE: This will replace the current configuration settings in the Universal Monitor
with the most recent backup.
Backup & Upload Configuration File - Backup (Service Terminal Interface only)
BACKUP AND UPLOAD CONFIGURATION FILE
Backup from panel saves panel configurations
Upload to panel restores panel configurations
Select to backup or upload file
1=BACKUP CONFIGURATION FILE
2=UPLOAD CONFIGURATION FILE
3=RETURN TO SETUP SYSTEM INFO MENU
4=RETURN TO SETUP MENU
5=RETURN TO MAIN MENU
SELECT A NUMBER:1
System and Control Options
72
Back Up the Configuration File
8. At the prompt to Initiate a Backup of Configuration File, enter Y (Yes - begin) or N (No - cancel).
The current setting appears in brackets—[N] in the following example.
9. At the top of the HyperTerminal window, shown below, click on Transfer, then on Receive File.
10. In the Receive File window, as shown above:
• In the Place Received File in the Following Folder box, enter the name and location of the
folder where the configuration file should be placed—for example, C:\downloads—or click
on the Browse button to locate the folder.
• In the Use Receiving Protocol box, select Xmodem from the drop-down list.
• Click on the Receive button. (To close the window without backing up the file, click on Close
or Cancel.)
11. In the Receive Filename window, enter a name for the file—for example, UMconfig.sav.
12. When the transfer is complete, a confirmation message appears in the Service Terminal Interface
window: “Backup Successful.”
>INITIATE A BACKUP OF CONFIGURATION FILE-YES(Y) OR NO(N)?
>[N]
>[
NOTE
The following instructions refer to the Microsoft Windows HyperTerminal program. These
steps may vary for other communications programs.
Enter filename -
for example,
UMconfig.sav
Select Xmodem
Enter folder
System and Control Options
73
Upload the Configuration File
13. At the prompt to Initiate an Upload of Configuration File, enter Y (Yes - begin) or N (No - cancel).
The current setting appears in brackets—[N] in the following example.
14. At the top of the HyperTerminal window, shown below, click on Transfer, then on Send File.
15. In the Send File window, as shown above:
• In the Filename box, enter the full path of the file to be uploaded—for example,
UMconfig.sav—or click on the Browse button to locate the file.
• In the Protocol box, select Xmodem from the drop-down list.
• Click on the Send button. (To close the window without sending the file, click on Close or
Cancel.)
16. When the transfer is complete, a confirmation message—“Upload Successful”—appears in the
Service Terminal Interface window and the Universal Monitor reboots with the new
configuration.
>INITIATE AN UPLOAD OF CONFIGURATION FILE-YES(Y) OR NO(N)?
>[N]
>[
NOTE
The following instructions refer to the Microsoft Windows HyperTerminal program. These
steps may vary for other communications programs.
Select Xmodem
Enter filename -
for example,
UMconfig.sav
Send button
System and Control Options
74
9.9.6 Setup Serv Ph Num - Enter Phone Number
The Service Phone Number (Serv Ph Num) is used for remote monitoring by Liebert Global Services.
The number is designed to allow remote monitoring services to connect to the Universal Monitor. All
alarms will be sent to this number. When an alarm occurs, this number is dialed before any of the
four pager numbers.
To use the service phone number features, be sure to connect the phone line connector to a telephone
wall jack using an RJ11 cord, as described in 4.6.2 - Phone Line Connector.
To set up the service phone number:
• From the Setup System Info Menu, use the arrows ↑↓ to choose
Setup Serv Ph Num, then press Enter ↵.
• See Table 33 for guidelines on entering the phone number, which
may consist of up to 40 characters. To enter the phone number:
• Use the arrows ↑↓ to choose a character.
• Press Enter ↵ to advance to the next character position.
• When finished, press Enter ↵ again.
Table 32 Service phone number dialing results
Result of Dialing Action Message Generated
Successful ——
Unsuccessful due to:
Busy signal / no answer /
no dial tone
Universal Monitor generates message after all three
redial attempts have failed, dials next configured pager.
Unsuccessful Page
(Event Log)
General modem
communication problem
Universal Monitor resets modem, generates
message, redials up to three more times.
Modem Reset
(Event Log)
No communication with modem
(internal hardware problem)
Universal Monitor generates messages, makes no
further dialing attempts.
Modem Internal Fault
(Active Alarm Report,
Alarm History Log)
Table 33 Guidelines for dialing service phone number
Device type Required entries Example
Remote
modem The first character must be “M”. M18005551212
Device type Optional entries Example
All types
of devices
Use “9” if needed to access an outside
line—place after first character (M). M918005551212
Use "W" to wait for a second dial tone
before dialing if the phone system has
two dial tones (initial tone and a second
tone for outside line)—place after “9”
(before the number to be dialed).
M9W18005551212
Use “,” (comma) to pause two seconds. M1,8005551212
Setup System Info Menu
SETUP SYSTEM INFO
CHANGE PASSWORD
CHANGE DATE & TIME
↑↓=NEXT ↵=SELECT
SETUP SITE ID
CONNECT BATTERY
> SETUP SERV PH NUM
FACTORY DEFAULTS
Setup Serv Ph Num
ENTER PHONE NUMBER
M18005551212
↑↓=SELECT ↵=NEXT/END
System and Control Options
75
9.9.7 Setup Serv Ph Num - Communications Check (Service Terminal Interface only)
The Service Terminal Interface offers two additional options for setting up the Service Phone Number
(Serv Ph Num) that are not available through the LCD interface:
• Enable communications check
• Enter time to perform communications check
To access these options:
• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see
A.2 - Connecting to the Service Terminal Interface).
• At the Main Menu, enter 0 (zero—Setup System-Login Required).
• At the Login Menu, enter your password.
• At the Setup Menu, enter 7 (Setup System Information).
• At the Setup System Information Menu, enter 6 (Setup Service Phone Number).
• At the Setup Service Phone Number menu, shown below, enter 1 to begin the setup.
• At the Enter Service Phone Number prompt, you may press Enter to bypass this option (or see
9.9.6 - Setup Serv Ph Num - Enter Phone Number for instructions on entering the number).
Enable Communications Check
Enabling this function permits a daily communications test between the Universal Monitor and the
selected service phone number. Once each day the Universal Monitor dials the service phone number
at a specified time and sends this message: “UNIVERSAL MONITOR COMM CHECK.” (The time of
the test is specified at the next prompt, Enter Time To Perform Communications Check.)
• At the Enable Communications Check prompt, enter Y (Yes - enable) or N (No - disable). The cur-
rent setting appears in brackets—[N] in the following example.
• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation mes-
sage appears: “Command Successful.”
Enter Time To Perform Communications Check
This function schedules the daily communications test between the Universal Monitor and the
selected service phone number, as described in the previous section.
• At the Enter Time To Perform Communications Check prompt, enter the time to initiate the com-
munications check, using the format HH:MM (hours and minutes in military time), ranging from
00:00 for midnight to 23:59 for 11:59 p.m. The current setting appears in brackets—[00:00] in the
following example.
• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation mes-
sage appears: “Command Successful.”
Setup Service Phone Number (Service Terminal Interface only)
SETUP SERVICE PHONE NUMBER
This number receives all alarms
in addition to the 4 pagers
CURRENT NUMBER
1=SETUP SERVICE PHONE NUMBER ******************
2=RETURN TO SETUP SYSTEM INFO MENU An “M” is required
3=RETURN TO SETUP MENU as 1st character.
4=RETURN TO MAIN MENU ******************
SELECT A NUMBER:1
>ENTER SERVICE PHONE NUMBER(40 CHARACTERS MAX).
>[]
>[
>COMMAND SUCCESSFUL
>ENABLE COMMUNICATIONS CHECK-YES(Y) OR NO(N)?
>[N]
>
>COMMAND SUCCESSFUL
>ENTER TIME TO PERFORM COMMUNICATIONS CHECK(HH:MM).
>[00:00]
>[
>COMMAND SUCCESSFUL
System and Control Options
76
9.9.8 Factory Defaults
At any time, you may restore all default values for settings in the Uni-
versal Monitor as it was shipped.
The password is the sole exception when reverting to the factory
default settings. The password can be reset to the factory default of
AAAA only through the DIP switches. For details, see Change
Password on page 69.
9.9.9 Perform Firmware Update (Service Terminal Interface only)
This function, which may be performed only through the Service Terminal Interface, upgrades the
Universal Monitor’s firmware to the newest version.
• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see
A.2 - Connecting to the Service Terminal Interface).
• At the Main Menu, enter 0 (zero—Setup System-Login Required).
• At the Login Menu, enter your password.
• At the Setup Menu, enter 7 (Setup System Information).
• At the Setup System Info menu, enter 8 (Perform Firmware Update).
• At the Perform Firmware Update menu, shown below, enter 1 to proceed with an update.
To perform the update:
1. At the Perform Firmware Update prompt, enter Y (Yes - begin) or N (No - cancel). The current
setting appears in brackets—[N] in the following example.
NOTE
This action will overwrite any configuration settings. You may
want to back up your settings before restoring the factory
defaults. See Backup and Upload Configuration File
(Service Terminal Interface only) in A.6.7 - Setup System
Info for details on backing up settings using the Service
Terminal Interface.
NOTE
This action will overwrite any configuration settings. You may
want to back up your settings before restoring the factory
defaults. See Backup and Upload Configuration File
(Service Terminal Interface only) in A.6.7 - Setup System
Info for details on backing up settings using the Service
Terminal Interface.
Firmware Update (Service Terminal Interface only)
PERFORM FIRMWARE UPDATE
This command will update
the existing firmware
1=PERFORM FIRMWARE UPDATE
2=RETURN TO SETUP SYSTEM INFO MENU
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:1
>PERFORM FIRMWARE UPDATE-YES(Y) OR NO(N)?
>[N]
>[
Setup System Info Menu
SETUP SYSTEM INFO
CHANGE PASSWORD
CHANGE DATE & TIME
↑↓=NEXT ↵=SELECT
SETUP SITE ID
CONNECT BATTERY
SETUP SERV PH NUM
> FACTORY DEFAULTS
Factory Defaults
RESTORE ALL DEFAULTS
ARE YOU SURE? N
↑↓=Y/N ↵=END
System and Control Options
77
2. The firmware update is a two-step process—this step describes how to upload the file
prog###.s19 (where ### is a number—for example, prog118.s19) to the Universal Monitor:
a. At the top of the HyperTerminal window, shown below, click on Transfer, then on Send File.
b. In the Send File window, as shown above:
• In the Filename box, enter the full path of the file to be uploaded—prog###.s19—or click
on the Browse button to locate the file.
• In the Protocol box, select Xmodem from the drop-down list.
• Click on the Send button. (To close the window without sending the file, click on Close or
Cancel.)
• When the transfer is complete, a confirmation message appears in the Service Terminal
Interface window.
3. Next, follow these steps to upload the file flash###.s19 (where ### is a number—for example,
flash607.s19) to the Universal Monitor:
a. At the top of the HyperTerminal window, shown above, click on Transfer, then on Send File.
b. In the Send File window, shown above:
• In the Filename box, enter the full path of the file to be uploaded—flash###.s19—or click
on the Browse button to locate the file.
• In the Protocol box, select Xmodem from the drop-down list.
• Click on the Send button. (To close the window without sending the file, click on Close or
Cancel.)
• When the transfer is complete, a confirmation message—“Firmware Update Successful”—
appears in the Service Terminal Interface window and the Universal Monitor reboots
with the new firmware update.
NOTE
The following instructions refer to the Microsoft Windows HyperTerminal program. These
steps may vary for other communications programs.
Select
Xmodem
Enter filename -
prog###.s19 or
flash###.s19
Send button
System and Control Options
78
9.9.10 Initiate Remote Alarm Test (Service Terminal Interface only)
The service phone number is used for remote monitoring by Liebert Global Services. The Service Ter-
minal Interface may be used to test communications between the Universal Monitor and the service
modem. This test will send a “DIAL OUT TEST PASSED” message to the service phone number.
The test is used to simulate an alarm to verify the proper configuration and functioning of the modem
and other communications required for receiving alarms. This simulated alarm bypasses the normal
alarm sequence—the LCD will not flash, the horn will not sound and there will be no record in the
Alarm Log. A message is sent to the service phone number only if the alarm system is set up correctly.
To initiate the remote alarm test:
• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see
A.2 - Connecting to the Service Terminal Interface).
• At the Main Menu, enter 0 (zero—Setup System-Login Required).
• At the Login Menu, enter your password.
• At the Setup Menu, enter 7 (Setup System Information).
• At the Setup System Info menu, enter 9 (Initiate Remote Alarm Test).
• At the Initiate Remote Alarm Test menu, shown below, enter 1 to initiate the remote alarm.
• At the Simulate An Alarm Condition prompt, enter Y if you wish to proceed or N if you want to
cancel the alarm simulation.
• After the “Command Successful” message appears, disconnect from the modem—at the top of the
HyperTerminal window, click on Call, then on Disconnect, as shown below.
• Wait for the Universal Monitor to dial out to send a test message.
• To verify whether the test was successful, check the Event Log (see 7.3 - View Event Log) for
one of these two messages: Dial out test passed or Dial out test failed.
If the test is NOT successful, check the following:
• Modem configuration (see 9.8.1 - Modem Setup - Initialization String)
• Pager configuration (see 9.8.3 - Pager Setup - Pager Number and PIN)
Initiate Remote Alarm Test (Service Terminal Interface only)
INITIATE REMOTE ALARM TEST
This command simulates an alarm
to test alarm notification setup
for the service phone number
1=INITIATE REMOTE ALARM TEST
2=RETURN TO SETUP SYSTEM INFO MENU
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:1
>SIMULATE AN ALARM CONDITION-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
NOTE
Also verify that a message was received at the Service Phone Number.
Disconnect
System and Control Options
79
9.10 Setup Exp Board - Optional Expansion Board
By default, the optional Expansion Board is configured as Not connected (N). After connecting power
to the board and connecting it to the Universal Monitor, you must specify the Expansion Board as
Connected (Y), as described in this section.
To change the Expansion Board connection setting:
Log In and Choose Setup System
• From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
• Enter your password at the Login screen.
• From the System and Control Menu, use the arrows ↑↓ to choose
Setup System, then press Enter ↵.
Identify the Expansion Board as Connected (Y) or Not Connected (N)
• From the Setup System Menu, shown at right, use the arrows ↑↓
to choose Setup Exp Board and press Enter ↵.
• To change this setting, use the arrows ↑↓ to choose Y (Yes - Con-
nected) or N (No - Not connected), then press Enter ↵.
NOTE
Before specifying the Expansion Board as Connected, be sure to connect power to the board and
connect it to the Universal Monitor. For more information, see:
•3.4 - Input Power Connections - Optional Expansion Board
•5.3.1 - Connect EIA485 Connectors to Main Board
Setup System Menu
SETUP INPUT
SETUP COMMON ALARM
SETUP SENSOR
SETUP I/O MATRIX
↑↓=NEXT ↵=SELECT
SETUP OUTPUT
SETUP MODEM&PAGERS
SETUP SYSTEM INFO
> SETUP EXP BOARD
Expansion Board
Connected
IS THE EXPANSION
BOARD CONNECTED? N
↑↓=Y/N ↵=END
System and Control Options
80
9.11 Manual Output Ctrl
The Manual Output Ctrl feature allows you to manually change the state of any digital output to ON
or OFF, overriding automatic control by the Universal Monitor (the default setting for all outputs).
This menu also allows you to release the manual override, returning any output to automatic control.
There are two ways to override automatic control of outputs:
• Use the Manual Output Ctrl menu, as described in this section, to turn any output ON or OFF.
• Use the switch on the Universal Monitor board (see 1.7 - Controller Board Overview) to force
all eight outputs ON at the same time. (Note: This has no effect on the optional Expansion Board
outputs.)
After an output is forced manually ON or OFF through the Manual Output Ctrl menu, it remains in
that state until returned to automatic control through this menu.
Table 34 summarizes the four types of control, including the abbreviated message that appears on
the LCD and in log reports.
To force an output point ON or OFF or return it to automatic control:
Log In and Choose Manual Output Ctrl
• From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
• Enter your password at the Login screen.
• From the System and Control Menu, use the arrows ↑↓ to choose
Manual Output Ctrl, then press Enter ↵.
Select an Output
The Select Output menu, shown at right, display the current status
of all eight outputs.
• Use the arrows ↑↓ to choose the output you want—for example,
Output01—and press Enter ↵.
Turn Output ON or OFF / Return to Automatic
• From the Override Output menu, use the arrows ↑↓ to choose
one of these options:
•Auto (return to automatic control)
•Man ON (manually turn this output ON)
•Man OFF (manually turn this output OFF)
• Press Enter ↵.
Table 34 Automatic / manual control - output points
Message Description
AUTO Automatic Controlled by Universal Monitor
MAN ON Manually ON This output forced ON or OFF
via Manual Output Ctrl menu
MAN OFF Manually OFF
HW MAN ON Manually ON
(all outputs)
All outputs forced ON
via hardware switch on circuit board
Main Menu
VIEW STATUS
> SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
Login
LOGIN
AAAA
↑↓=SELECT ↵=NEXT/END
System & Control Menu
SETUP SYSTEM
> MANUAL OUTPUT CTRL
CLEAR ALARMS & LOGS
↑↓=NEXT ↵=SELECT
Select Output
OVERRIDE OUTPUT
> OUTPUT01 AUTO
OUTPUT02 AUTO
↑↓=NEXT ↵=SELECT
OUTPUT03 AUTO
OUTPUT04 MAN ON
OUTPUT05 AUTO
OUTPUT06 AUTO
OUTPUT07 MAN OFF
OUTPUT08 AUTO
OUTPUT09 AUTO
OUTPUT10 MAN ON
OUTPUT11 AUTO
OUTPUT12 AUTO
OUTPUT13 MAN OFF
OUTPUT14 AUTO
OUTPUT15 AUTO
OUTPUT16 AUTO
Override Output
SELECT OUTPUT01
AUTO
↑↓=SELECT ↵=END
NOTE: OUTPUT09-OUTPUT16
for optional Expansion Board
System and Control Options
81
9.12 Clear Alarms & Logs
The Clear Alarms & Logs menu allows you to clear active alarms or
delete all records from any of the Universal Monitor’s three logs:
alarm, event and trend logs.
To clear alarms or logs:
Log In and Choose Clear Alarms & Logs
• From the Main Menu, use the arrows ↑↓ to choose System and
Control, then press Enter ↵ (see 9.1 - Login for help).
• Enter your password at the Login screen.
• From the System and Control Menu, use the arrows ↑↓ to choose
Clear Alarms & Logs, then press Enter ↵.
• Use the following steps to clear alarms or delete log records.
9.12.1 Clear Active Alarms
To clear all active alarms:
• From the Clear Alarms/Logs Menu, use the arrows ↑↓ to choose
Clear Active Alarms, then press Enter ↵.
• Use the arrows ↑↓ to choose Y (Yes - clear all active alarms) or
N(No - do not clear alarms), then press Enter ↵.
Clearing active alarms is the only means to reset latched alarms. This
step is required to return latched points to their normal state. To set up
a digital input or an analog sensor input as latched, see:
•9.3.4 - Set Up Alarmable Inputs in Latched or Unlatched
Mode
•9.5.8 - Set Up Alarmable Sensors in Latched or Unlatched
Mode
9.12.2 Clear the Alarm Log
The alarm log contains up to 99 records of alarms that have occurred.
You may want to clear the log after backing up the file or simply to
free up space.
To delete all records from the alarm log:
• From the Clear Alarms/Logs Menu, use the arrows ↑↓ to choose
Clear Alarm Log, then press Enter ↵.
• Use the arrows ↑↓ to choose Y (Yes - clear the alarm log) or
N(No - do not clear the alarm log), then press Enter ↵.
NOTE
Before deleting the records in the alarm log, you may want to
back up the file to a remote computer using the Service
Terminal Interface, as described in 8.2 - Back Up Log Files
(Service Terminal Interface only).
NOTE
Clear active alarms is the only means to reset Latched alarms.
This action must be taken to return Latched points to their
normal state.
Main Menu
VIEW STATUS
> SYSTEM AND CONTROL
↑↓=NEXT ↵=SELECT
Login
LOGIN
AAAA
↑↓=SELECT ↵=NEXT/END
System & Control Menu
SETUP SYSTEM
MANUAL OUTPUT CTRL
> CLEAR ALARMS & LOGS
↑↓=NEXT ↵=SELECT
Clear Alarms/Logs Menu
> CLEAR ACTIVE ALARMS
CLEAR ALARM LOG
CLEAR EVENT LOG
↑↓=NEXT ↵=SELECT
CLEAR TREND LOGS
Clear Active Alarms
CLEAR ACTIVE ALARMS
ARE YOU SURE? N
↑↓=Y/N ↵=END
Clear Alarms/Logs Menu
CLEAR ACTIVE ALARMS
> CLEAR ALARM LOG
CLEAR EVENT LOG
↑↓=NEXT ↵=SELECT
CLEAR TREND LOG
Clear Alarm Log
CLEAR ALARM LOG
ARE YOU SURE? N
↑↓=Y/N ↵=END
System and Control Options
82
9.12.3 Clear the Event Log
The event log contains up to 99 records of events detected by the Uni-
versal Monitor. You may want to clear the log after backing up the file
or simply to free up space.
To delete all records from the event log:
• From the Clear Alarms/Logs Menu, use the arrows ↑↓ to choose
Clear Event Log, then press Enter ↵.
• Use the arrows ↑↓ to choose Y (Yes - clear the event log) or N (No -
do not clear the event log), then press Enter ↵.
9.12.4 Clear the Trend Logs
The Universal Monitor maintains a separate trend log for each config-
ured analog input sensor. Each log contains up to 100 records of data
collected at regular intervals. You may want to clear the logs after
backing up the files or simply to free up space.
Using the Clear Trend Logs command will clear all four trend logs
maintained by the Universal Monitor. There is no method of clearing
records from individual logs.
To delete the records from ALL four trend logs:
• From the Clear Alarms/Logs Menu, use the arrows ↑↓ to choose Clear Trend Logs, then press
Enter ↵.
• Use the arrows ↑↓ to choose Y (Yes - clear all trend logs) or N (No - do not clear the trend logs),
then press Enter ↵.
NOTE
Before deleting the records in the event log, you may want to
back up the file to a remote computer using the Service
Terminal Interface, as described in 8.2 - Back Up Log Files
(Service Terminal Interface only).
NOTE
Before deleting the records in the trend logs, you may want to
back up the files to a remote computer using the Service
Terminal Interface, as described in 8.2 - Back Up Log Files
(Service Terminal Interface only).
Clear Alarms/Logs Menu
CLEAR ACTIVE ALARMS
CLEAR ALARM LOG
> CLEAR EVENT LOG
↑↓=NEXT ↵=SELECT
CLEAR TREND LOGS
Clear Event Log
CLEAR EVENT LOG
ARE YOU SURE? N
↑↓=Y/N ↵=END
Clear Alarms/Logs Menu
CLEAR ACTIVE ALARMS
CLEAR ALARM LOG
CLEAR EVENT LOG
↑↓=NEXT ↵=SELECT
> CLEAR TREND LOGS
Clear Trend Log
CLEAR TREND LOGS
ARE YOU SURE? N
↑↓=Y/N ↵=END
Specifications
83
10.0 SPECIFICATIONS
10.1 Universal Monitor Specifications
Power
Requirements
Small Enclosure Large Enclosure NOTE
UMS02400 115VAC
UML11500
230VAC
UML23000
If the equipment is
used in a manner
not specified by the
manufacturer, the
protection provided
by the equipment
may be impaired.
24VAC ±10%
of nominal;
50/60 Hz, 1.3A,
30VA
115VAC ±10%
of nominal;
60Hz, 4A,
460VA
230VAC ±10%
of nominal;
50Hz, 0.5A,
115VA
Dimensions
W x D x H, in. (mm)
14-1/4 x 2-3/4 x 12
(361.95 x 69.85 x 304.8)
18 x 2-3/4 x 18
(457.2 x 69.85 x 457.2)
Weight (Assembled) 7.68 lb. (3.48 kg) 20.56 lb. (9.33 kg)
Enclosure Type NEMA 1
Liquid Crystal Display (LCD) Four line, 20 character, backlit
Mounting Surface Building Wall or Structural Member
Ambient Operating
Environment
32ºF to 104ºF (0ºC to 40ºC)
0% RH to 95% RH (non-condensing)
Processor Specifics
Model Motorola XC68HC812A4
Clock speed 16MHz
Total RAM 256Kb
Total FLASH 4M
Total EEPROM 4K
A/D Resolution (Analog IN) 12 Bit
Modem Type Embedded 14.4K bps
Clock Type Real-Time Clock
Clock battery backup type Lithium Cell (non-replaceable)
Clock battery life 7 years, constant, no power
Modem battery backup type Nickel Cadmium (replaceable)
Modem battery life 10 minutes at full load
Communications
Local Communications RS232
Remote Communications
Modem (9600-N-8-1)
Supported pagers
Baud rate 9600 bps, Parity=None, Data bits=8, Stop bits=1
9600 E-7-1 supports TAPI protocol version 1.8
SiteScan Web IGM Protocol, EIA422
Expansion Board (optional) EIA485
Agency Listings
No Transformer Module With Transformer Module
(UMS02400) 115VAC
(TM115)
230VAC
(TM230)
UL UL3121 UL1012 UL1585
CSA C22.2 No. 1010 C22.2 No. 66 and
C22.2 No. 107.1
CE Yes Yes
FCC Compliance CFR 47 Part 15 N/A
Inputs & Outputs (Quantity)
Digital Inputs (8) Dry Contact Closure 24VDC, 10 mA
Analog Inputs (4) 4-20 mA signal input with selectable
power source of 12VDC or 24VDC
Digital Outputs (8) 24VAC, 3A
Common Alarm Outputs (2) 24VAC, 3A
Specifications
84
10.2 Optional Expansion Board Specifications
Power
Requirements
UMEXP NOTE
If the equipment is
used in a manner
not specified by the
manufacturer, the
protection provided
by the equipment
may be impaired.
24VAC ±10% of nominal;
50/60 Hz, 0.6A, 15VA Class 2
Dimensions
W x D x H, in. (mm)
14-1/4 x 2-3/4 x 12
(361.95 x 69.85 x 304.8)
Weight (Assembled) 7.68 lb. (3.48 kg)
Enclosure Type NEMA 1
Mounting Surface Building Wall or Structural Member
Ambient Operating
Environment
32ºF to 104ºF (0ºC to 40ºC)
0% RH to 95% RH (non-condensing)
Inputs & Outputs (Quantity)
Digital Inputs (16) Dry Contact Closure
24VDC, 10 mA
Digital Outputs (8) 240VAC, 2A
Service Terminal Interface
85
APPENDIX A- SERVICE TERMINAL INTERFACE
The Service Terminal Interface allows access to all functions of the Universal Monitor, including
some that are not possible through the LCD interface. This interface is accessible through any com-
puter using a communications program such as Microsoft® Windows® HyperTerminal.
This appendix provides directions for connecting to the Service Terminal Interface, an overview of
each type of function and sample screens for each menu available through the Service Terminal Inter-
face. References to more detailed instructions about each function are provided.
A.1 COMPARISON OF FUNCTIONS: LCD AND SERVICE TERMINAL INTERFACE
Table 35 lists all functions for viewing and configuring the Universal Monitor and shows whether
they can be performed through the LCD interface and where to find information.
Table 35 Guide to Universal Monitor functions
Function
Can be performed via: Where to find:
LCD
Service
Terminal
Instructions on
using function
Service Terminal
screen examples
VIEW STATUS FUNCTIONS
View Active Alarms ✔✔ page 33 page 93
View Alarm Log ✔✔ page 34 page 94
View Event Log ✔✔ page 35 page 95
View Trend Log ✔✔ page 36 page 96
View Input Status ✔✔ page 37 page 97
View Output Status ✔✔ page 38 page 98
View Pager Numbers ✔✔ page 39 page 99
SILENCE ALARM & BACK UP LOGS FUNCTIONS
Silence Alarm (On the LCD, press any key to silence an alarm) ✔✔ page 40 page 100
Back Up Log Files — ✔page 41 page 101
SYSTEM & CONTROL FUNCTIONS
Login ✔✔ page 43 page 104
Setup System ✔✔ page 45 page 105
Setup Input ✔✔ page 45 page 106
Setup Common Alarm ✔✔ page 48 page 108
Setup Sensor ✔✔ page 49 page 109
Setup I/O Matrix ✔✔ page 55 page 111
Setup Output ✔✔ page 58 page 117
Pager Setup - Pager Number & PIN ✔✔ page 64 page 119
Pager Setup - Communications Check — ✔page 66 page 119
Modem Setup - Initialization String ✔✔ page 60 page 120
Modem Setup - Enter Universal Monitor Phone Number — ✔page 62 page 120
Modem Setup - Enable Modem Diagnostic Messages — ✔page 62 page 120
Modem Setup - Change Modem Dial Prefix — ✔page 62 page 120
Modem Setup - Change Modem Hang Up Delay After a Call — ✔page 62 page 120
Setup System Info ✔✔ page 68 page 121
Change Password ✔✔ page 69 page 121
Change Date & Time/Automatic Daylight Saving Time ✔✔ page 69 page 122
Setup Site ID ✔✔ page 70 page 122
Connect Battery ✔✔ page 70 page 123
Backup and Upload Configuration File — ✔page 71 page 123
Setup Serv Ph Num - Enter Phone Number ✔✔ page 74 page 124
Setup Serv Ph Num - Communications Check — ✔page 75 page 124
Factory Defaults ✔✔ page 76 page 125
Perform Firmware Update — ✔page 76 page 125
Initiate Remote Alarm Test — ✔page 78 page 126
Setup Exp Board - Optional Expansion Board ✔✔ page 79 page 127
Manual Output Ctrl ✔✔ page 80 page 128
Clear Alarms & Logs ✔✔ page 81 page 130
Clear Active Alarms ✔✔ page 81 page 130
Clear the Alarm Log ✔✔ page 81 page 130
Clear the Event Log ✔✔ page 82 page 131
Clear the Trend Logs ✔✔ page 82 page 131
Connecting to the Service Terminal Interface
86
A.2 CONNECTING TO THE SERVICE TERMINAL INTERFACE
This section describes how to set up and connect to the Service Terminal Interface.
A.2.1 Connection Methods
There are two ways to access the Service Terminal Interface:
•Direct—Use a null modem cable to connect a computer’s COM1 port to the Universal Monitor’s
RS232 port,
OR
•Remote—Use a remote computer’s modem to dial the telephone number of the phone line con-
nected to the Universal Monitor.
Both methods require a communications program, such as HyperTerminal, to connect to the Service
Terminal Interface.
Refer to Table 36 for step-by-step instructions to set up each type of connection. Note that the remote
connection does not require setting up the COM1 port.
The instructions in this section refer to the HyperTerminal program—they may vary for other com-
munications programs.
Table 36 Steps to set up a direct or remote connection
Direct Remote
A.2.2 - Create a Connection ✔✔
A.2.3 - Set Up the COM1 Port - Direct Connection Only ✔N/A
A.2.4 - Set Up the Connection’s Properties ✔✔
A.2.5 - Connect to the Service Terminal Interface ✔✔
Connecting to the Service Terminal Interface
87
A.2.2 Create a Connection
Before connecting to the Service Terminal Interface, you must create a connection and specify the
method to be used for connection, as described in the following steps.
1. Start the HyperTerminal program—to do this, click on the Start button, then on Programs, then
Accessories, then Communications, and finally HyperTerminal.
2. At the top of the HyperTerminal window, click on File, then on New Connection, as shown
below left.
3. In the Connection Description window, shown above right, enter a name for the connection—for
example, Universal Monitor. This becomes the file name (with the extension “.ht”).
4. Click OK to close the window. The Connect To window opens, as shown below.
5. In the Connect To window, select the appropriate connection method from the Connect Using
drop-down list:
Direct Connection via RS232
• To set up a direct connection via the Universal Monitor’s RS232 port, select COM1 as shown
above left.
• This opens the COM1 Properties window. Proceed to Step 6 (next section).
Remote Connection via Modem
• To make a remote connection through the Universal Monitor’s modem, select your computer’s
modem—HSP56 MicroModem in the example shown above right.
• Enter the area code and phone number of the Universal Monitor’s modem.
• Proceed to Step 8 in A.2.4 - Set Up the Connection’s Properties (skip Steps 6 and 7).
Enter a name for
the connection -
for example,
Universal
Monitor
(DIRECT CONNECTION)
Choose COM1
(REMOTE CONNECTION)
Choose the computer’s modem
Connecting to the Service Terminal Interface
88
A.2.3 Set Up the COM1 Port - Direct Connection Only
The following steps apply only to setting up a direct connection to the Service Terminal Interface via
the Universal Monitor’s RS232 port. If you are setting up a remote connection via modem, skip to
Step 8 (next section).
COM1 Port Setup
6. In the COM1 Properties window, shown below, make the following selections:
• Bits per second: 9600
• Data bits: 8
•Parity: None
• Stop bits: 1
• Flow control: None
7. Click OK. When the connection is open, the connection name appears in the title bar of the
HyperTerminal window. To complete the setup, continue with Step 8 (next section).
Connecting to the Service Terminal Interface
89
A.2.4 Set Up the Connection’s Properties
The following steps are needed for both direct and remote connection to the Universal Monitor.
Properties Setup
8. Open the Properties window by clicking on File, then on Properties, as shown below left.
9. In the Properties window, above right, click on the Settings tab and choose the following settings:
• Function, arrow, and ctrl keys act as: Terminal keys
• Backspace key sends: Ctrl+H
• Emulation: ANSIW
• Telnet terminal ID: VT100
• Backscroll buffer lines: 500
• Play sound when connecting or disconnecting: Unchecked
ASCII Setup
10. In the Properties window, click on the ASCII Setup button, shown below left.
11. In the ASCII Setup window, shown above right, choose the following settings:
• ASCII Sending: place a check mark (✔) in the Send Line Ends With Line Feeds box.
• ASCII Receiving: place a check mark (✔) in the Wrap Lines That Exceed Terminal Width box.
•Click OK.
The setup is now complete. To use the new connection, proceed to the next section, A.2.5 - Connect
to the Service Terminal Interface.
Settings
tab
ASCII
Setup
button
Connecting to the Service Terminal Interface
90
A.2.5 Connect to the Service Terminal Interface
After creating and setting up a connection, use a communications program such as HyperTerminal to
access the Universal Monitor’s Service Terminal Interface.
1. Verify communications connections between the remote computer and the Universal Monitor:
a. For direct connection (via RS232 port):
• Connect a null modem cable from the computer’s COM1 port to the Universal Monitor’s
RS232 port (for location, see 4.6.1 - RS232 Connector).
b. For remote connection (via modem):
• Verify modem connections between the remote computer and the Universal Monitor. The
remote computer should have connectivity through a telephone line, high-speed cable or an
Ethernet. The Universal Monitor must have a telephone line connected to its RJ11 port (for
location, see 4.6.2 - Phone Line Connector).
2. Start the HyperTerminal program—click on the Start button, then on Programs, then
Accessories, then Communications, and finally HyperTerminal.
3. Open the Universal Monitor connection created in A.2.2 - Create a Connection. To do this, click
on File, then on Open, as shown below.
4. In the Open window, shown above right, select the file name—Universal Monitor.ht in this
example—and then click on the Open button.
5. Follow the steps below to display the Main Menu of the Service Terminal Interface:
a. For direct connection (via RS232 port):
• Press Enter (or Escape) to initiate communication and bring up the Main Menu.
b. For remote connection (via modem):
• The Connect window opens, as shown below left. Click the OK button.
• In the Connect window, below right, click Dial.
• If the dialing attempt is successful, the Main Menu appears.
For more information on the Universal Monitor’s options:
• See A.3 - Overview of Menus for examples of the Service Terminal Interface screens.
• See Table 35 to locate step-by-step instructions for each Universal Monitor function.
Click on the
file name -
for example,
Universal
Monitor.ht
OK button
Dial button
Overview of Menus
91
A.3 OVERVIEW OF MENUS
The Main Menu offers choices for viewing the status of the Universal Monitor, silencing the audible
alarm and backing up the unit’s log files. It also allows access to the System and Control features,
which require a password.
The following shows where to find examples of the Main Menu screens:
A.3.1 View Status Overview
The View Status features are available to all users. This permits all personnel to check on the status
of any equipment or location being monitored. These options allow any user to:
• View current monitoring data—active alarms and the status of all inputs and outputs
• View data stored in alarm, event and trend logs
• View pager numbers
A.3.2 Silence Alarm and Backup Log Files
Two Main Menu options—Silence Alarm and Backup Log Files—are unique to the Service Terminal
Interface. As with the View Status options, these features do not require a password:
•Silence Alarm—silence the Universal Monitor’s audible alarm and reset the Common Alarm
Relay output.
•Backup Log Files—make backup copies of the Universal Monitor’s Alarm Log, Event Log and
Trend Logs and save the copies to a computer.
A.3.3 Setup Menu Overview
The Setup Menu options require a password. Authorized users may:
• Configure the Universal Monitor—this includes setting up digital and analog inputs, digital out-
puts, the modem, up to four pagers, and system features such as setting the date and time
Three system features—Backup and Upload Configuration File, Firmware Update and
Initiate Remote Alarm Test—are unique to the Service Terminal Interface.
• Override automatic control of outputs to force an output ON or OFF
• Clear active alarms and delete all records in the alarm, event and trend logs
Main Menu For sample screens, see:
1=VIEW ACTIVE ALARMS A.4 - View Status Menus
2=VIEW ALARM LOG
3=VIEW EVENT LOG
4=VIEW TREND LOG
5=VIEW INPUT & SENSOR STATUS
6=VIEW OUTPUT STATUS
7=VIEW PAGER NUMBERS
8=SILENCE ALARM A.5 - Silence Alarm & Back Up
Log Files (Service Terminal
Interface only)9=BACKUP LOG FILES
0=SETUP SYSTEM-LOGIN REQUIRED A.6 - Setup Menu
View Status Menus
92
A.4 VIEW STATUS MENUS
The View Status menu allows any user to view currently active alarms, monitoring data stored in the
alarm, event and trend logs, the status of all inputs and outputs, and the four pager numbers.
Main Menu
After connecting to the Service Terminal Interface, the Main Menu appears, as shown below. This
section presents Service Terminal Interface screens for options 1 through 7:
Main Menu
LIEBERT UNIVERSAL MONITOR
VX.XXX.X
LIEBERT CORPORATION COPYRIGHT 2003
ALL RIGHTS RESERVED
MAIN MENU
For sample screens, see:
1=VIEW ACTIVE ALARMS Section A.4.1
2=VIEW ALARM LOG Section A.4.2
3=VIEW EVENT LOG Section A.4.3
4=VIEW TREND LOG Section A.4.4
5=VIEW INPUT & SENSOR STATUS Section A.4.5
6=VIEW OUTPUT STATUS Section A.4.6
7=VIEW PAGER NUMBERS Section A.4.7
8=SILENCE ALARM
9=BACKUP LOG FILES
0=SETUP SYSTEM-LOGIN REQUIRED
SELECT A NUMBER:1
View Status Menus
93
A.4.1 View Active Alarms
For details on this feature, see 7.1 - View Active Alarms.
View Active Alarms
ACTIVE ALARMS
Input points/hardware
presently in an alarm state
SENSOR_1 101.1 DEG
HIGH SETPOINT ALARM
SENSOR_2 ------ DEG
SENSOR PROBLEM
INPUT_07 ALARM
CONTACT OPEN
BATTERY
CHECK BATTERY
<ENTER>=MORE <ESC>=EXIT <A>=ALL
1=REFRESH ACTIVE ALARMS
2=RETURN TO MAIN MENU
SELECT A NUMBER:
View Status Menus
94
A.4.2 View Alarm Log
For details on this feature, see 7.2 - View Alarm Log.
View Alarm Log
ALARM LOG
Alarm history
SENSOR_2 80.0 DEG
HIGH SETPOINT ALARM
29-AUG-02 09:29:10
MODEM
INTERNAL FAULT
29-AUG-02 09:20:10
INPUT_08 ALARM
CONTACT CLOSED
29-AUG-02 09:19:10
SENSOR_2 79.0 DEG
RETURN TO NORMAL
28-AUG-02 19:29:10
<ENTER>=MORE <ESC>=EXIT <A>=ALL
SENSOR_2 ------ DEG
SENSOR PROBLEM
28-AUG-02 15:08:10
SYSTEM
LOSS OF POWER
19-AUG-02 02:50:10
BATTERY
LOW BATTERY
18-AUG-02 05:23:10
BATTERY
BATTERY UNPLUGGED
12-AUG-02 22:47:10
1=REFRESH ALARM LOG
2=RETURN TO MAIN MENU
SELECT A NUMBER:
View Status Menus
95
A.4.3 View Event Log
For details on this feature, see 7.3 - View Event Log.
View Event Log
EVENT LOG
Event history
PAGER
UNSUCCESSFUL PAGE
07-MAY-02 10:29:10
OUTPUT01 MAN ON
CONTACT CLOSED
07-MAY-02 09:20:10
OUTPUT08 ON
CONTACT OPEN
07-MAY-02 08:20:10
OUTPUT08 MAN OFF
CONTACT CLOSED
07-MAY-02 06:20:10
<ENTER>=MORE <ESC>=EXIT <A>=ALL
SENSOR_2 ------ DEG
SENSOR PROBLEM
06-MAY-02 07:10:10
SYSTEM
USER LOGIN
19-APR-02 02:50:10
LIEBERT GLOBAL SERV
DIAL OUT TEST FAILED
18-APR-02 05:23:10
MODEM
MODEM RESET
12-MAR-02 22:47:10
LIEBERT GLOBAL SERV
DIAL OUT TEST PASSED
12-MAR-02 05:23:10
<ENTER>=MORE <ESC>=EXIT <A>=ALL
1=REFRESH EVENT LOG
2=RETURN TO MAIN MENU
SELECT A NUMBER:
View Status Menus
96
A.4.4 View Trend Log
For details on this feature, see 7.4 - View Trend Log.
View Trend Log
TREND LOG
Trend history
for each sensor
Select sensor for trend
you want to view.
1=SENSOR_1
2=SENSOR_2
3=SENSOR_3
4=SENSOR_4
5=RETURN TO MAIN MENU
SELECT A NUMBER:1
TREND LOG
Trend history
SENSOR_1 75.4 DEG
NORMAL
28-AUG-02 15:45:10
SENSOR_1 70.5 DEG
LOW SETPOINT EVENT
28-AUG-02 15:15:10
SENSOR_1 79.9 DEG
RETURN TO NORMAL
28-AUG-02 14:45:10
SENSOR_1 ------ DEG
SENSOR PROBLEM
28-AUG-02 14:15:10
<ENTER>=MORE <ESC>=EXIT <A>=ALL
SENSOR_1 65.9 DEG
LOW SETPOINT ALARM
28-AUG-02 13:45:10
SENSOR_1 69.9 DEG
LOW SETPOINT EVENT
28-AUG-02 13:15:10
SENSOR_1 80.7 DEG
HIGH SETPOINT EVENT
28-AUG-02 12:45:10
1=REFRESH TREND LOG
2=VIEW A DIFFERENT SENSOR
3=RETURN TO MAIN MENU
SELECT A NUMBER:
View Status Menus
97
A.4.5 View Input Status
For details on this feature, see 7.5 - View Input Status.
View Input & Sensor Status
INPUT & SENSOR STATUS
Sensor values & discrete inputs status
INPUT STATUS/VALUE
SENSOR_1 80.0 DEG
SENSOR_2 ------ DEG
SENSOR_3 80.0 DEG
SENSOR_4 79.5 RH
INPUT_01 NORMAL
INPUT_02 ALARM
INPUT_03 EVENT
INPUT_04 ALARM
INPUT_05 ALARM
INPUT_06 EVENT
INPUT_07 NORMAL
INPUT_08 NORMAL
INPUT_09 EVENT
INPUT_10 NORMAL
INPUT_11 NORMAL
<ENTER>=MORE <ESC>=EXIT <A>=ALL
INPUT_12 NORMAL
INPUT_13 ALARM
INPUT_14 EVENT
INPUT_15 ALARM
INPUT_16 ALARM
INPUT_17 EVENT
INPUT_18 NORMAL
INPUT_19 NORMAL
INPUT_20 EVENT
INPUT_21 NORMAL
INPUT_22 NORMAL
INPUT_23 NORMAL
INPUT_24 NORMAL
1=VIEW SENSOR_1 DYNAMICALLY
2=VIEW SENSOR_2 DYNAMICALLY
3=VIEW SENSOR_3 DYNAMICALLY
4=VIEW SENSOR_4 DYNAMICALLY
5=REFRESH INPUT & SENSOR STATUS
6=RETURN TO MAIN MENU
SELECT A NUMBER:1
VIEWING SENSOR_1 DYNAMICALLY
SENSOR_1 80.0 DEG
PRESS <ESC> KEY TO EXIT
View Status Menus
98
A.4.6 View Output Status
For details on this feature, see 7.6 - View Output Status.
View Output Status
OUTPUT STATUS
Discrete outputs status
OUTPUT STATUS
OUTPUT01 ON
OUTPUT02 OFF
OUTPUT03 ON
OUTPUT04 MAN ON
OUTPUT05 ON
OUTPUT06 OFF
OUTPUT07 MAN OFF
OUTPUT08 ON
OUTPUT09 ON
OUTPUT10 OFF
OUTPUT11 ON
OUTPUT12 MAN ON
OUTPUT13 ON
OUTPUT14 OFF
<ENTER>=MORE <ESC>=EXIT <A>=ALL
OUTPUT15 ON
OUTPUT16 OFF
1=REFRESH OUTPUT STATUS
2=RETURN TO MAIN MENU
SELECT A NUMBER:
View Status Menus
99
A.4.7 View Pager Numbers
For details on this feature, see 7.7 - View Pager Numbers.
View Pager Numbers
PAGER & PIN NUMBERS
Numbers to dial
for an alarm
PAGER 1 NUMBER
A1,8005551212
PAGER 1 PIN
01234567891011121314
PAGER 2 NUMBER
A9W1,8005551212
PAGER 2 PIN
01234567891011121314
<ENTER>=MORE <ESC>=EXIT <A>=ALL
PAGER 3 NUMBER
N18005551212,,,,1234567#
PAGER 3 PIN
PAGER 4 NUMBER
M1,8005551212
PAGER 4 PIN
1=REFRESH PAGER NUMBERS
2=RETURN TO MAIN MENU
SELECT A NUMBER:
Silence Alarm & Back Up Log Files (Service Terminal Interface only)
100
A.5 SILENCE ALARM & BACK UP LOG FILES (SERVICE TERMINAL INTERFACE ONLY)
This section presents two options from the Main Menu that are available via the Service Terminal
Interface only.
Main Menu
After connecting to the Service Terminal Interface, the Main Menu appears, as shown below. This
section presents Service Terminal Interface screens for options 8 and 9:
A.5.1 Silence Alarm (Service Terminal Interface only)
For details on this feature, see 8.1 - Silence Alarm (Service Terminal Interface).
Main Menu
LIEBERT UNIVERSAL MONITOR
V5.300.2
LIEBERT CORPORATION COPYRIGHT 2002
ALL RIGHTS RESERVED
MAIN MENU
1=VIEW ACTIVE ALARMS
2=VIEW ALARM LOG
3=VIEW EVENT LOG
4=VIEW TREND LOG
5=VIEW INPUT & SENSOR STATUS
6=VIEW OUTPUT STATUS
7=VIEW PAGER NUMBERS For sample screens, see:
8=SILENCE ALARM Section A.5.1
9=BACKUP LOG FILES Section A.5.2
0=SETUP SYSTEM-LOGIN REQUIRED
SELECT A NUMBER:1
Silence Alarm
SILENCE ALARM
Silence alarm and reset
common alarm relay if
common alarm relay is
configured to reset with
silence alarm
1=SILENCE ALARM
2=RETURN TO MAIN MENU
SELECT A NUMBER:1
>ALARM HAS BEEN SILENCED
Silence Alarm & Back Up Log Files (Service Terminal Interface only)
101
A.5.2 Back Up Log Files (Service Terminal Interface only)
For details on this feature, see 8.2 - Back Up Log Files (Service Terminal Interface only).
Back Up Alarm Log File
Backup Log Files - Alarm Log File
BACKUP LOG FILES
Backup alarm, event and trend log files
1=BACKUP ALARM LOG FILE
2=BACKUP EVENT LOG FILE
3=BACKUP TREND LOG FILE-SENSOR_1
4=BACKUP TREND LOG FILE-SENSOR_2
5=BACKUP TREND LOG FILE-SENSOR_3
6=BACKUP TREND LOG FILE-SENSOR_4
7=RETURN TO MAIN MENU
SELECT A NUMBER:1
>INITIATE A BACKUP OF ALARM LOG-YES(Y) OR NO(N)?
>[N]
>[
INSTRUCTIONS TO PERFORM BACKUP:
ASSUMES USING MICROSOFT WINDOWS HYPERTERMINAL APPLICATION
- SELECT TRANSFER FROM THE TOOLBAR
- SELECT RECEIVE FILE
- ENTER FOLDER WHERE FILE IS TO BE RECEIVED
- SELECT XMODEM FROM THE PROTOCOL BOX
- SELECT RECEIVE BUTTON AND ENTER FILE NAME, E.G., ALARM.LOG
>BACKUP SUCCESSFUL
Silence Alarm & Back Up Log Files (Service Terminal Interface only)
102
Back Up Event Log File
Backup Log Files - Event Log File
BACKUP LOG FILES
Backup alarm, event and trend log files
1=BACKUP ALARM LOG FILE
2=BACKUP EVENT LOG FILE
3=BACKUP TREND LOG FILE-SENSOR_1
4=BACKUP TREND LOG FILE-SENSOR_2
5=BACKUP TREND LOG FILE-SENSOR_3
6=BACKUP TREND LOG FILE-SENSOR_4
7=RETURN TO MAIN MENU
SELECT A NUMBER:2
>INITIATE A BACKUP OF EVENT LOG-YES(Y) OR NO(N)?
>[N]
>[
INSTRUCTIONS TO PERFORM BACKUP:
ASSUMES USING MICROSOFT WINDOWS HYPERTERMINAL APPLICATION
- SELECT TRANSFER FROM THE TOOLBAR
- SELECT RECEIVE FILE
- ENTER FOLDER WHERE FILE IS TO BE RECEIVED
- SELECT XMODEM FROM THE PROTOCOL BOX
- SELECT RECEIVE BUTTON AND ENTER FILE NAME, E.G., EVENT.LOG
>BACKUP SUCCESSFUL
Silence Alarm & Back Up Log Files (Service Terminal Interface only)
103
Back Up Trend Log Files
Backup Log Files - Trend Log Files
BACKUP LOG FILES
Backup alarm, event and trend log files
1=BACKUP ALARM LOG FILE
2=BACKUP EVENT LOG FILE
3=BACKUP TREND LOG FILE-SENSOR_1
4=BACKUP TREND LOG FILE-SENSOR_2
5=BACKUP TREND LOG FILE-SENSOR_3
6=BACKUP TREND LOG FILE-SENSOR_4
7=RETURN TO MAIN MENU
SELECT A NUMBER:3
>INITIATE A BACKUP OF TREND LOG-YES(Y) OR NO(N)?
>[N]
>[
INSTRUCTIONS TO PERFORM BACKUP:
ASSUMES USING MICROSOFT WINDOWS HYPERTERMINAL APPLICATION
- SELECT TRANSFER FROM THE TOOLBAR
- SELECT RECEIVE FILE
- ENTER FOLDER WHERE FILE IS TO BE RECEIVED
- SELECT XMODEM FROM THE PROTOCOL BOX
- SELECT RECEIVE BUTTON AND ENTER FILE NAME, E.G., SENSOR_1.LOG
>BACKUP SUCCESSFUL
Setup Menu
104
A.6 SETUP MENU
The Setup menu allows the user to configure the Universal Monitor—setting up inputs and outputs
and an input/output matrix to trigger actions, the modem and pagers, and system features such as
date and time. This menu also provides a vehicle for manually changing the state of an output to ON
or OFF, clearing active alarms and deleting records from the Universal Monitor’s alarm log, event log
and trend logs.
Main Menu
After connecting to the Service Terminal Interface, the Main Menu appears, as shown below.
• Choose 0 to access the features illustrated in this section.
Login Menu
The System and Control options require a password to prevent unauthorized users from making
changes to the system. After choosing 0 in the Main Menu above, the Login Menu appears:
• Enter the password, and the Setup Menu appears, as shown in the following section.
Main Menu
LIEBERT UNIVERSAL MONITOR
VX.XXX.X
LIEBERT CORPORATION COPYRIGHT 2003
ALL RIGHTS RESERVED
MAIN MENU
1=VIEW ACTIVE ALARMS
2=VIEW ALARM LOG
3=VIEW EVENT LOG
4=VIEW TREND LOG
5=VIEW INPUT & SENSOR STATUS
6=VIEW OUTPUT STATUS
7=VIEW PAGER NUMBERS
8=SILENCE ALARM
9=BACKUP LOG FILES
0=SETUP SYSTEM-LOGIN REQUIRED
SELECT A NUMBER:0
Login
YOU MUST LOGIN TO PERFORM
SETUP OR TO MAKE CHANGES
LOGIN WITH 4 CHARACTER
PASSWORD
>****
>INVALID PASSWORD, ENTER AGAIN
>PRESS <ESC> TO EXIT
>
Setup Menu
105
Setup Menu
This section presents Service Terminal Interface screens for each of the following:
* Setup System Information features are:
• Change Password
• Change Date & Time/Automatic Daylight Saving Time
• Setup Site ID
• Connect Battery
• Backup and Upload Configuration File (Service Terminal Interface only)
• Setup Service Phone Number
•Factory Defaults
• Firmware Update (Service Terminal Interface only)
• Initiate Remote Alarm Test (Service Terminal Interface only)
Note that three of these system features—Backup and Upload Configuration File, Firm-
ware Update and Initiate Remote Alarm Test—are unique to the Service Terminal Interface.
Tips on Using the Service Terminal Interface
Use the following tips when making changes in the Service Terminal Interface:
• Data that can be entered is shown in parentheses ( ) in prompt line.
• The current setting is shown in brackets [ ] in the line below the prompt
• To accept the current setting, press the Enter key.
• To change the current setting, enter the value and then press Enter.
• Pressing Escape will exit the current setup function or take you to the previous menu screen.
Setup Menu
SETUP MENU See: Description
1=SETUP INPUT Section A.6.1 Configure digital inputs
2=SETUP COMMON ALARM Section A.6.2 Set up the common alarm to reset with silence
3=SETUP SENSOR Section A.6.3 Configure analog inputs
4=SETUP I/O MATRIX Section A.6.4 Set up mapping for inputs to trigger actions in outputs
5=SETUP OUTPUT Section A.6.5 Configure digital outputs
6=SETUP MODEM&PAGERS Section A.6.6 Configure modem and up to four pager numbers
7=SETUP SYSTEM INFORMATION* Section A.6.7 Set up features such as password and date & time*
8=SETUP EXPANSION BOARD Section A.6.8 Specify the Expansion Board as connected
9=OVERRIDE OUTPUT Section A.6.9 Manually override automatic control of outputs
0=CLEAR ALARMS&LOGS Section A.6.10 Clear active alarms; clear alarm, event and trend logs
I=RETURN TO MAIN MENU
SELECT A NUMBER:
>CHANGE LABEL(8 CHARACTERS MAX).
>[INPUT_01]
>[
>COMMAND SUCCESSFUL
>IS INPUT NORMALLY OPENED(NO) OR NORMALLY CLOSED(NC)?
>[NO]
>[
>COMMAND SUCCESSFUL
Values that may
be entered shown
in parentheses ( )
Current
setting
shown in
brackets [ ]
Setup Menu
106
A.6.1 Setup Input
For details on this feature, see 9.3 - Setup System - Setup Input.
Setup Input - Main Board Outputs
SETUP INPUT
Setup for discrete
input points
Select input to edit
INPUT DEFINITION
1=INPUT_01 NO-EV-NL-00:01
2=INPUT_02 NO-AL-L -00:01
3=INPUT_03 NC-EV-NL-00:01
4=INPUT_04 NO-AL-L -00:01
5=INPUT_05 NC-AL-L -00:01
6=INPUT_06 NO-EV-NL-00:01
7=INPUT_07 NO-AL-L -00:01
8=INPUT_08 NC-EV-NL-00:01
9=EXPANSION BOARD INPUTS
0=RETURN TO SETUP MENU
I=RETURN TO MAIN MENU
SELECT A NUMBER:1
****************************
NO=NORMALLY OPENED
NC=NORMALLY CLOSED
EV=EVENT
AL=ALARMABLE
NL=NOT LATCHED
L =LATCHED
MIN:SEC=DELAY TIME BEFORE
INPUT WILL TRIGGER
NOTE:EVENT CANNOT BE LATCHED
****************************
>CHANGE LABEL(8 CHARACTERS MAX).
>[INPUT_01]
>[
>COMMAND SUCCESSFUL
>IS INPUT NORMALLY OPENED(NO) OR NORMALLY CLOSED(NC)?
>[NO]
>[
>COMMAND SUCCESSFUL
>IS INPUT AN ALARM(AL) OR EVENT(EV)?
>[EV]
>[
>COMMAND SUCCESSFUL
>IS ALARM LATCHED-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>DELAY TIME BEFORE TRIGGER (MM:SS)?
>[00:01]
>[
>COMMAND SUCCESSFUL
Setup Menu
107
Setup Input - Expansion Board Inputs
SETUP INPUT
Setup for discrete
input points
Select input to edit
INPUT DEFINITION
1=INPUT_01 NO-EV-NL-00:01
2=INPUT_02 NO-AL-L -00:01
3=INPUT_03 NC-EV-NL-00:01
4=INPUT_04 NO-AL-L -00:01
5=INPUT_05 NC-AL-L -00:01
6=INPUT_06 NO-EV-NL-00:01
7=INPUT_07 NO-AL-L -00:01
8=INPUT_08 NC-EV-NL-00:01
9=EXPANSION BOARD INPUTS
0=RETURN TO SETUP MENU
I=RETURN TO MAIN MENU
SELECT A NUMBER:9
****************************
NO=NORMALLY OPENED
NC=NORMALLY CLOSED
EV=EVENT
AL=ALARMABLE
NL=NOT LATCHED
L =LATCHED
MIN:SEC=DELAY TIME BEFORE
INPUT WILL TRIGGER
NOTE:EVENT CANNOT BE LATCHED
****************************
SETUP INPUT
1=INPUT_09 NO-EV-NL-00:01
2=INPUT_10 NO-AL-L -00:01
3=INPUT_11 NC-EV-NL-00:01
4=INPUT_12 NO-AL-L -00:01
5=INPUT_13 NC-AL-L -00:01
6=INPUT_14 NO-EV-NL-00:01
7=INPUT_15 NO-AL-L -00:01
8=INPUT_16 NC-EV-NL-00:01
9=INPUT_17 NC-EV-NL-00:01
0=INPUT_18 NC-EV-NL-00:01
A=INPUT_19 NC-EV-NL-00:01
B=INPUT_20 NC-EV-NL-00:01
C=INPUT_21 NC-EV-NL-00:01
D=INPUT_22 NC-EV-NL-00:01
E=INPUT_23 NC-EV-NL-00:01
F=INPUT_24 NC-EV-NL-00:01
G=RETURN TO SETUP MENU
H=RETURN TO MAIN MENU
SELECT A NUMBER:1
****************************
NO=NORMALLY OPENED
NC=NORMALLY CLOSED
EV=EVENT
AL=ALARMABLE
NL=NOT LATCHED
L =LATCHED
MIN:SEC=DELAY TIME BEFORE
INPUT WILL TRIGGER
NOTE:EVENT CANNOT BE LATCHED
****************************
>CHANGE LABEL(8 CHARACTERS MAX).
>[INPUT_09]
>[
>COMMAND SUCCESSFUL
>IS INPUT NORMALLY OPENED(NO) OR NORMALLY CLOSED(NC)?
>[NO]
>[
>COMMAND SUCCESSFUL
>IS INPUT AN ALARM(AL) OR EVENT(EV)?
>[EV]
>[
>COMMAND SUCCESSFUL
>IS ALARM LATCHED-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>DELAY TIME BEFORE TRIGGER MM:SS)?
>[00:01]
>[
>COMMAND SUCCESSFUL
Setup Menu
108
A.6.2 Setup Common Alarm
For details on this feature, see 9.4 - Setup System - Setup Common Alarm.
Setup Common Alarm
SETUP COMMON ALARM
Select if the common
alarm relay contact
is to reset with
silence alarm CURRENT
SETTING
1=SETUP COMMON ALARM N
2=RETURN TO SETUP MENU
3=RETURN TO MAIN MENU
SELECT A NUMBER:1
>RESET COMMON ALARM WITH SILENCE-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
Setup Menu
109
A.6.3 Setup Sensor
For details on this feature, see 9.5 - Setup System - Setup Sensor.
Setup Sensor
SETUP SENSOR
Setup for analog
input points
Select sensor to edit
SENSOR VALUE
1=SENSOR_1 80.0 DEG
2=SENSOR_2 ------ DEG
3=SENSOR_3 80.0 DEG
4=SENSOR_4 79.5 RH
5=RETURN TO SETUP MENU
6=RETURN TO MAIN MENU
SELECT A NUMBER:1
>IS THE SENSOR CONNECTED-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>CHANGE SENSOR LABEL(8 CHARACTERS MAX).
>[SENSOR_1]
>[
>COMMAND SUCCESSFUL
>CHANGE UNITS LABEL(3 CHARACTERS MAX).
>[DEG]
>[
>COMMAND SUCCESSFUL
>CHANGE 4 mA VALUE(-999.9 to 999.9).
>[-020.0]
>[
>COMMAND SUCCESSFUL
>CHANGE 20 mA VALUE(-999.9 to 999.9).
>[+020.0]
Setup Menu
110
>[
>COMMAND SUCCESSFUL
>CHANGE OFFSET VALUE.
>[000.0]
>[
>COMMAND SUCCESSFUL
>IS SENSOR AN ALARM(AL) OR EVENT(EV)?
>[AL]
>[
>COMMAND SUCCESSFUL
>IS SENSOR ALARM LATCHED-YES(Y) OR NO(N)?
>[Y]
>[
>COMMAND SUCCESSFUL
>CHANGE LOW SETPOINT.
>[-0015.0]
>[
>COMMAND SUCCESSFUL
>CHANGE HIGH SETPOINT.
>[+0015.0]
>[
>COMMAND SUCCESSFUL
>DELAY TIME BEFORE TRIGGER (MM:SS)?
>[00:01]
>[
>COMMAND SUCCESSFUL
Setup Sensor (continued)
Setup Menu
111
A.6.4 Setup I/O Matrix
For details on this feature, see 9.6 - Setup System - Setup I/O Matrix.
Setup I-O Matrix - Map Input to Output - Main Board Inputs
SETUP I/O MATRIX
Program inputs & sensors
to control outputs
Select to map inputs or sensors
1=MAP INPUT TO OUTPUT
2=MAP SENSOR TO OUTPUT
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:1
MAP INPUT TO OUTPUT
Program input
to control output(s)
Select input to map
INPUT OUTPUTS
12345678910111213141516
1=INPUT_01 YNNNNNNNN N N N N N N N
2=INPUT_02 NYNNNNNNN N N N N N N N
3=INPUT_03 NNYNNNNNN N N N N N N N
4=INPUT_04 NNNYNNNNN N N N N N N N
5=INPUT_05 NNNNYNNNN N N N N N N N
6=INPUT_06 NNNNNYNNN N N N N N N N
7=INPUT_07 NNNNNNYNN N N N N N N N
8=INPUT_08 NNNNNNNYN N N N N N N N
9=EXPANSION BOARD INPUTS
0=RETURN TO SETUP I/O MATRIX
I=RETURN TO SETUP MENU
SELECT A NUMBER:1
**********************
OUTPUT OUTPUT
NUMBER DESCRIPTION
OUTPUT01 = OUTPUT01
OUTPUT02 = OUTPUT02
OUTPUT03 = OUTPUT03
OUTPUT04 = OUTPUT04
OUTPUT05 = OUTPUT05
OUTPUT06 = OUTPUT06
OUTPUT07 = OUTPUT07
OUTPUT08 = OUTPUT08
OUTPUT09 = OUTPUT09
OUTPUT10 = OUTPUT10
OUTPUT11 = OUTPUT11
OUTPUT12 = OUTPUT12
OUTPUT13 = OUTPUT13
OUTPUT14 = OUTPUT14
OUTPUT15 = OUTPUT15
OUTPUT16 = OUTPUT16
**********************
>MAP INPUT_01 TO OUTPUT01-YES(Y) OR NO(N)?
>[Y]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT02-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT03-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT04-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT05-YES(Y) OR NO(N)?
>[N]
Setup Menu
112
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT06-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT07-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT08-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT09-YES(Y) OR NO(N)?
>[Y]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT10-YES(Y) OR NO(N)?
>[Y]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT11-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT12-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT13-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT14-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT15-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_01 TO OUTPUT16-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
Setup I-O Matrix - Map Input to Output - Main Board Inputs (continued)
Setup Menu
113
Setup I-O Matrix - Map Input to Output - Expansion Board Inputs
SETUP I/O MATRIX
Program inputs & sensors
to control outputs
Select to map inputs or sensors
1=MAP INPUT TO OUTPUT
2=MAP SENSOR TO OUTPUT
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:1
MAP INPUT TO OUTPUT
Program input
to control output(s)
Select input to map
INPUT OUTPUTS
12345678910111213141516
1=INPUT_01 YNNNNNNNN N N N N N N N
2=INPUT_02 NYNNNNNNN N N N N N N N
3=INPUT_03 NNYNNNNNN N N N N N N N
4=INPUT_04 NNNYNNNNN N N N N N N N
5=INPUT_05 NNNNYNNNN N N N N N N N
6=INPUT_06 NNNNNYNNN N N N N N N N
7=INPUT_07 NNNNNNYNN N N N N N N N
8=INPUT_08 NNNNNNNYN N N N N N N N
9=EXPANSION BOARD INPUTS
0=RETURN TO SETUP I/O MATRIX
I=RETURN TO SETUP MENU
SELECT A NUMBER:9
**********************
OUTPUT OUTPUT
NUMBER DESCRIPTION
OUTPUT01 = OUTPUT01
OUTPUT02 = OUTPUT02
OUTPUT03 = OUTPUT03
OUTPUT04 = OUTPUT04
OUTPUT05 = OUTPUT05
OUTPUT06 = OUTPUT06
OUTPUT07 = OUTPUT07
OUTPUT08 = OUTPUT08
OUTPUT09 = OUTPUT09
OUTPUT10 = OUTPUT10
OUTPUT11 = OUTPUT11
OUTPUT12 = OUTPUT12
OUTPUT13 = OUTPUT13
OUTPUT14 = OUTPUT14
OUTPUT15 = OUTPUT15
OUTPUT16 = OUTPUT16
**********************
MAP INPUT TO OUTPUT
12345678910111213141516
1=INPUT_09 NNNNNNNNN N N N N N N N
2=INPUT_10 NNNNNNNNN N N N N N N N
3=INPUT_11 NNNNNNNNN N N N N N N N
4=INPUT_12 NNNNNNNNN N N N N N N N
5=INPUT_13 NNNNNNNNN N N N N N N N
6=INPUT_14 NNNNNNNNN N N N N N N N
7=INPUT_15 NNNNNNNNN N N N N N N N
8=INPUT_16 NNNNNNNNN N N N N N N N
9=INPUT_17 NNNNNNNNN N N N N N N N
0=INPUT_18 NNNNNNNNN N N N N N N N
A=INPUT_19 NNNNNNNNN N N N N N N N
B=INPUT_20 NNNNNNNNN N N N N N N N
C=INPUT_21 NNNNNNNNN N N N N N N N
D=INPUT_22 NNNNNNNNN N N N N N N N
E=INPUT_23 NNNNNNNNN N N N N N N N
F=INPUT_24 NNNNNNNNN N N N N N N N
G=RETURN TO SETUP I/O MATRIX
H=RETURN TO SETUP MENU
SELECT A NUMBER:9
**********************
OUTPUT OUTPUT
NUMBER DESCRIPTION
OUTPUT01 = OUTPUT01
OUTPUT02 = OUTPUT02
OUTPUT03 = OUTPUT03
OUTPUT04 = OUTPUT04
OUTPUT05 = OUTPUT05
OUTPUT06 = OUTPUT06
OUTPUT07 = OUTPUT07
OUTPUT08 = OUTPUT08
OUTPUT09 = OUTPUT09
OUTPUT10 = OUTPUT10
OUTPUT11 = OUTPUT11
OUTPUT12 = OUTPUT12
OUTPUT13 = OUTPUT13
OUTPUT14 = OUTPUT14
OUTPUT15 = OUTPUT15
OUTPUT16 = OUTPUT16
**********************
Setup Menu
114
>MAP INPUT_09 TO OUTPUT01-YES(Y) OR NO(N)?
>[Y]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT02-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT03-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT04-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT05-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT06-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT07-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT08-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT09-YES(Y) OR NO(N)?
>[Y]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT10-YES(Y) OR NO(N)?
>[Y]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT11-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT12-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT13-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT14-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT15-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP INPUT_09 TO OUTPUT16-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
Setup I-O Matrix - Map Input to Output - Expansion Board Inputs (continued)
Setup Menu
115
Setup I-O Matrix - Map Sensor to Output
SETUP I/O MATRIX
Program inputs & sensors
to control outputs
Select to map inputs or sensors
1=MAP INPUT TO OUTPUT
2=MAP SENSOR TO OUTPUT
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:2
MAP SENSOR TO OUTPUT
Program sensor
to control output(s)
Select sensor to map
SENSOR OUTPUTS
12345678910111213141516
1=SENSOR_1 HIGH STPT NNNNNNNNN N N N N N N N
2=SENSOR_1 LOW STPT NNNNNNNNN N N N N N N N
3=SENSOR_2 HIGH STPT NNNNNNNNN N N N N N N N
4=SENSOR_2 LOW STPT NNNNNNNNN N N N N N N N
5=SENSOR_3 HIGH STPT NNNNNNNNN N N N N N N N
6=SENSOR_3 LOW STPT NNNNNNNNN N N N N N N N
7=SENSOR_4 HIGH STPT NNNNNNNNN N N N N N N N
8=SENSOR_4 LOW STPT NNNNNNNNN N N N N N N N
9=RETURN TO SETUP I/O MATRIX
0=RETURN TO SETUP MENU
SELECT A NUMBER:1
**********************
OUTPUT OUTPUT
NUMBER DESCRIPTION
OUTPUT01 = OUTPUT01
OUTPUT02 = OUTPUT02
OUTPUT03 = OUTPUT03
OUTPUT04 = OUTPUT04
OUTPUT05 = OUTPUT05
OUTPUT06 = OUTPUT06
OUTPUT07 = OUTPUT07
OUTPUT08 = OUTPUT08
OUTPUT09 = OUTPUT09
OUTPUT10 = OUTPUT10
OUTPUT11 = OUTPUT11
OUTPUT12 = OUTPUT12
OUTPUT13 = OUTPUT13
OUTPUT14 = OUTPUT14
OUTPUT15 = OUTPUT15
OUTPUT16 = OUTPUT16
**********************
>MAP SENSOR_1 HIGH STPT TO OUTPUT01-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT02-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT03-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT04-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT05-YES(Y) OR NO(N)?
>[N]
Setup Menu
116
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT06-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT07-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT08-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT08-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT09-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT10-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT11-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT12-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT13-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT14-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT15-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
>MAP SENSOR_1 HIGH STPT TO OUTPUT16-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
Setup I-O Matrix - Map Sensor to Output (continued)
Setup Menu
117
A.6.5 Setup Output
For details on this feature, see 9.7 - Setup System - Setup Output.
Setup Output - Main Board Outputs
SETUP OUTPUT
Setup for discrete
output points
Select output to edit
OUTPUT DEFINITION
1=OUTPUT01 NO
2=OUTPUT02 NC
3=OUTPUT03 NO ******************
4=OUTPUT04 NC NO=NORMALLY OPENED
5=OUTPUT05 NO NC=NORMALLY CLOSED
6=OUTPUT06 NC ******************
7=OUTPUT07 NO
8=OUTPUT08 NC
9=EXPANSION BOARD OUTPUTS
0=RETURN TO SETUP MENU
I=RETURN TO MAIN MENU
SELECT A NUMBER:1
>CHANGE LABEL(8 CHARACTERS MAX).
>[OUTPUT01]
>[
>COMMAND SUCCESSFUL
>SET TO NORMALLY OPENED(NO) OR NORMALLY CLOSED(NC).
>[NO]
>[
>COMMAND SUCCESSFUL
Setup Menu
118
Setup Output - Expansion Board Outputs
SETUP OUTPUT
Setup for discrete
output points
Select output to edit
OUTPUT DEFINITION
1=OUTPUT01 NO
2=OUTPUT02 NC
3=OUTPUT03 NO ******************
4=OUTPUT04 NC NO=NORMALLY OPENED
5=OUTPUT05 NO NC=NORMALLY CLOSED
6=OUTPUT06 NC ******************
7=OUTPUT07 NO
8=OUTPUT08 NC
9=EXPANSION BOARD OUTPUTS
0=RETURN TO SETUP MENU
I=RETURN TO MAIN MENU
SELECT A NUMBER:9
SETUP OUTPUT
Setup for discrete
output points
Select output to edit
OUTPUT DEFINITION
1=OUTPUT09 NO
2=OUTPUT10 NC
3=OUTPUT11 NO
4=OUTPUT12 NC ******************
5=OUTPUT13 NO NO=NORMALLY OPENED
6=OUTPUT14 NC NC=NORMALLY CLOSED
7=OUTPUT15 NO
8=OUTPUT16 NC NOTE:SET BY DIPSWITCH
9=RETURN TO SETUP MENU ******************
0=RETURN TO MAIN MENU
SELECT A NUMBER:1
>CHANGE LABEL(8 CHARACTERS MAX).
>[OUTPUT09]
>[
>COMMAND SUCCESSFUL
Setup Menu
119
A.6.6 Setup Modem & Pagers
For details on this topic, see 9.8 - Setup System - Setup Modem & Pagers.
Pager Setup
For details on this feature, see 9.8.3 - Pager Setup - Pager Number and PIN and 9.8.4 - Pager
Setup - Communications Check (Service Terminal Interface only).
Setup Modem & Pagers - Pager Setup
SETUP MODEM&PAGERS
Input pager and
modem information
Select pager or modem
CURRENT NUMBER
*******************
1=PAGER NUMBER 1 An "A" is required
2=PAGER NUMBER 2 as 1st character
3=PAGER NUMBER 3 for an alpha pager,
4=PAGER NUMBER 4 an "N" for a numeric
5=MODEM CONFIGURATION pager, and an "M"
6=RETURN TO SETUP MENU for a remote modem.
7=RETURN TO MAIN MENU *******************
SELECT A NUMBER:1
>ENTER PAGER NUMBER(40 CHARACTERS MAX).
>[]
>[
>COMMAND SUCCESSFUL
>ENTER PAGER PIN NUMBER (20 CHARACTERS MAX).
>[]
>[
>COMMAND SUCCESSFUL
>ENABLE COMMUNICATIONS CHECK-YES(Y) OR NO(N)? (Service Terminal Interface only)
>[N]
>[
>COMMAND SUCCESSFUL
>ENTER TIME TO PERFORM COMMUNICATIONS CHECK(HH:MM). (Service Terminal Interface only)
>[00:00]
>[
>COMMAND SUCCESSFUL
Setup Menu
120
Modem Setup
For details on this feature, see 9.8.1 - Modem Setup - Initialization String and 9.8.2 - Modem
Setup - Additional Features (Service Terminal Interface only).
Setup Modem & Pagers - Modem Setup
SETUP MODEM&PAGERS
Input pager and
modem information
Select pager or modem
CURRENT NUMBER
*******************
1=PAGER NUMBER 1 An "A" is required
2=PAGER NUMBER 2 as 1st character
3=PAGER NUMBER 3 for an alpha pager,
4=PAGER NUMBER 4 an "N" for a numeric
5=MODEM CONFIGURATION pager, and an "M"
6=RETURN TO SETUP MENU for a remote modem.
7=RETURN TO MAIN MENU *******************
SELECT A NUMBER:5
>CHANGE MODEM INITIALIZATION STRING(40 CHARACTERS MAX).
>[ATS0=1]
>[
>COMMAND SUCCESSFUL
>ENTER UNIVERSAL MONITOR PHONE NUMBER(40 CHARACTERS MAX). (Service Terminal Interface only)
>[]
>[
>COMMAND SUCCESSFUL
>ENABLE MODEM DIAGNOSTIC MESSAGES-YES(Y) OR NO(N)? (Service Terminal Interface only)
>[N]
>[
>COMMAND SUCCESSFUL
>CHANGE MODEM DIAL PREFIX. (Service Terminal Interface only)
>[ATE0X4DT]
>[
>COMMAND SUCCESSFUL
>CHANGE MODEM HANG UP DELAY AFTER A CALL(99 SEC MAX). (Service Terminal Interface only)
>[10]
>[
>COMMAND SUCCESSFUL
Setup Menu
121
A.6.7 Setup System Info
This section presents Service Terminal Interface screens for choices 1 through 9 in the Setup System
Information menu shown below. For details on this topic, see 9.9 - Setup System - Setup System
Info.
Change Password
For details on this feature, see 9.9.1 - Change Password.
Setup System Info
SETUP SYSTEM INFORMATION
1=CHANGE PASSWORD
2=CHANGE DATE & TIME
3=SETUP SITE ID
4=CONNECT BATTERY
5=BACKUP & UPLOAD CONFIGURATION FILE
6=SETUP SERVICE PHONE NUMBER
7=SET PANEL TO FACTORY DEFAULTS
8=PERFORM FIRMWARE UPDATE
9=INITIATE REMOTE ALARM TEST
0=RETURN TO SETUP MENU
I=RETURN TO MAIN MENU
SELECT A NUMBER:
Change Password
CHANGE PASSWORD
1=CHANGE PASSWORD
2=RETURN TO SETUP SYSTEM INFO MENU
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:1
>ENTER ORIGINAL PASSWORD(MUST BE 4 CHARACTERS).
>
>ENTER NEW PASSWORD(MUST BE 4 CHARACTERS).
>
>ENTER NEW PASSWORD AGAIN FOR CONFIRMATION.
>
>PASSWORD CHANGE SUCCESSFUL
Setup Menu
122
Change Date & Time/Automatic Daylight Saving Time
For details on this feature, see 9.9.2 - Change Date & Time/Automatic Daylight Saving Time.
Setup Site ID
For details on this feature, see 9.9.3 - Setup Site ID.
Change Date & Time
CHANGE DATE & TIME
CURRENT DATE & TIME DST
1=CHANGE DATE & TIME 28-AUG-02 14:45:10 Y
2=RETURN TO SETUP SYSTEM INFO MENU
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:1
>CHANGE DATE & TIME(DD-MON-YY HR:MM:SS).
>[28-AUG-02 14:45:10]
>[
>COMMAND SUCCESSFUL
>ENABLE DAYLIGHT SAVINGS TIME-YES(Y) OR NO(N)?
>[Y]
>[
>COMMAND SUCCESSFUL
Setup Site ID
SETUP SITE ID
Define name to
reference panel
CURRENT SITE ID
1=SETUP SITE ID
2=RETURN TO SETUP SYSTEM INFO MENU
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:1
>ENTER SITE ID NAME(40 CHARACTERS MAX).
>[]
>[
>COMMAND SUCCESSFUL
Setup Menu
123
Connect Battery
For details on this feature, see 9.9.4 - Connect Battery.
Backup and Upload Configuration File (Service Terminal Interface only)
For details on this feature, see 9.9.5 - Backup and Upload Configuration File (Service Termi-
nal Interface only).
Connect Battery
CONNECT BATTERY
CURRENT SETTING
1=CONNECT BATTERY Y
2=RETURN TO SETUP SYSTEM INFO MENU
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:1
>IS THE BATTERY CONNECTED-YES(Y) OR NO(N)?
>[Y]
>[
>COMMAND SUCCESSFUL
Backup & Upload Configuration File - Backup
BACKUP AND UPLOAD CONFIGURATION FILE
Backup from panel saves panel configurations
Upload to panel restores panel configurations
Select to backup or upload file
1=BACKUP CONFIGURATION FILE
2=UPLOAD CONFIGURATION FILE
3=RETURN TO SETUP SYSTEM INFO MENU
4=RETURN TO SETUP MENU
5=RETURN TO MAIN MENU
SELECT A NUMBER:1
>INITIATE A BACKUP OF CONFIGURATION FILE-YES(Y) OR NO(N)?
>[N]
>[
INSTRUCTIONS TO PERFORM BACKUP:
ASSUMES USING MICROSOFT WINDOWS HYPERTERMINAL APPLICATION
- SELECT TRANSFER FROM THE TOOLBAR
- SELECT RECEIVE FILE
- ENTER FOLDER WHERE FILE IS TO BE RECEIVED
- SELECT XMODEM FROM THE PROTOCOL BOX
- SELECT RECEIVE BUTTON AND ENTER FILE NAME,E.G., UMCONFIG.SAV
>BACKUP SUCCESSFUL
Setup Menu
124
Setup Service Phone Number
For details on this feature, see 9.9.6 - Setup Serv Ph Num - Enter Phone Number and 9.9.7 -
Setup Serv Ph Num - Communications Check (Service Terminal Interface only).
Backup & Upload Configuration File - Upload
BACKUP AND UPLOAD CONFIGURATION FILE
Backup from panel saves panel configurations
Upload to panel restores panel configurations
Select to backup or upload file
1=BACKUP CONFIGURATION FILE
2=UPLOAD CONFIGURATION FILE
3=RETURN TO SETUP SYSTEM INFO MENU
4=RETURN TO SETUP MENU
5=RETURN TO MAIN MENU
SELECT A NUMBER:2
>INITIATE AN UPLOAD OF CONFIGURATION FILE-YES(Y) OR NO(N)?
>[N]
>[
INSTRUCTIONS TO PERFORM UPLOAD:
ASSUMES USING MICROSOFT WINDOWS HYPERTERMINAL APPLICATION
- SELECT TRANSFER FROM THE TOOLBAR
- SELECT SEND FILE
- ENTER FILE NAME-CONFIGURATION FILE LOCATION & NAME
- SELECT XMODEM FROM THE PROTOCOL BOX
- SELECT SEND BUTTON
>UPLOAD SUCCESSFUL
Setup Service Phone Number
SETUP SERVICE PHONE NUMBER
This number receives all alarms
in addition to the 4 pagers
CURRENT NUMBER
1=SETUP SERVICE PHONE NUMBER ******************
2=RETURN TO SETUP SYSTEM INFO MENU An “M” is required
3=RETURN TO SETUP MENU as 1st character.
4=RETURN TO MAIN MENU ******************
SELECT A NUMBER:1
>ENTER SERVICE PHONE NUMBER(40 CHARACTERS MAX).
>[]
>[
>COMMAND SUCCESSFUL
>ENABLE COMMUNICATIONS CHECK-YES(Y) OR NO(N)? (Service Terminal Interface only)
>[N]
>
>COMMAND SUCCESSFUL
>ENTER TIME TO PERFORM COMMUNICATIONS CHECK(HH:MM). (Service Terminal Interface only)
>[00:00]
>[
>COMMAND SUCCESSFUL
Setup Menu
125
Factory Defaults
For details on this feature, see 9.9.8 - Factory Defaults.
Firmware Update (Service Terminal Interface only)
For details on this feature, see 9.9.9 - Perform Firmware Update (Service Terminal Interface
only).
Factory Defaults
RESTORE FACTORY DEFAULTS
This command restores all panel
information to factory settings
1=RESTORE FACTORY DEFAULTS
2=RETURN TO SETUP SYSTEM INFO MENU
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:1
>RESTORE THE PANEL TO FACTORY SETTINGS-YES(Y) OR NO(N)?
>[N]
[[
>COMMAND SUCCESSFUL
Firmware Update
PERFORM FIRMWARE UPDATE
This command will update
the existing firmware
1=PERFORM FIRMWARE UPDATE
2=RETURN TO SETUP SYSTEM INFO MENU
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:1
>PERFORM FIRMWARE UPDATE-YES(Y) OR NO(N)?
>[N]
>[
INSTRUCTIONS TO PERFORM FIRMWARE UPDATE:
ASSUMES USING MICROSOFT WINDOWS HYPERTERMINAL APPLICATION
- SELECT TRANSFER FROM THE TOOLBAR
- SELECT SEND FILE
- ENTER FILE NAME-FIRMWARE FILE LOCATION & NAME
- SELECT XMODEM FROM THE PROTOCOL BOX
- SELECT SEND BUTTON
>WAITING TO SEND PROGRAM FILE
>DONE
>CHECKSUM IS....
>PROGRAM VERSION....
>WAITING TO SEND FLASH FILE
>DONE
>FIRMWARE UPDATE SUCCESSFUL
Setup Menu
126
Initiate Remote Alarm Test (Service Terminal Interface only)
For details on this feature, see 9.9.10 - Initiate Remote Alarm Test (Service Terminal Interface
only).
Initiate Remote Alarm Test
INITIATE REMOTE ALARM TEST
This command simulates an alarm
to test alarm notification setup
for the service phone number
1=INITIATE REMOTE ALARM TEST
2=RETURN TO SETUP SYSTEM INFO MENU
3=RETURN TO SETUP MENU
4=RETURN TO MAIN MENU
SELECT A NUMBER:1
>SIMULATE AN ALARM CONDITION-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
Setup Menu
127
A.6.8 Connect Expansion Board
For details on this feature, see 9.10 - Setup Exp Board - Optional Expansion Board.
Connect Expansion Board
CONNECT EXPANSION BOARD
CURRENT SETTING
1=CONNECT EXPANSION BOARD N
2=RETURN TO SETUP MENU
3=RETURN TO MAIN MENU
SELECT A NUMBER:1
>IS THE EXPANSION BOARD CONNECTED-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
Setup Menu
128
A.6.9 Override Output
For details on this feature, see 9.11 - Manual Output Ctrl.
Override Output - Main Board Outputs
OVERRIDE OUTPUT
Manually override
an output point
Select output to override
OUTPUT CONTROL
1=OUTPUT01 AUTO
2=OUTPUT02 AUTO ********************************************
3=OUTPUT03 AUTO AUTO =CONTROL BY PANEL
4=OUTPUT04 AUTO MAN ON =OVERRIDE IN ON POSITION BY OPERATOR
5=OUTPUT05 AUTO MAN OFF=OVERRIDE IN OFF POSITION BY OPERATOR
6=OUTPUT06 AUTO ********************************************
7=OUTPUT07 AUTO
8=OUTPUT08 AUTO
9=EXPANSION BOARD OUTPUTS
0=RETURN TO SETUP MENU
I=RETURN TO MAIN MENU
SELECT A NUMBER:1
>OVERRIDE OUTPUT OUTPUT01-AUTO(2),MAN ON(1),MAN OFF(0).
>[2]
>[
>COMMAND SUCCESSFUL
Setup Menu
129
Override Output - Expansion Board Outputs
OVERRIDE OUTPUT
Manually override
an output point
Select output to override
OUTPUT CONTROL
1=OUTPUT01 AUTO
2=OUTPUT02 AUTO
3=OUTPUT03 AUTO ********************************************
4=OUTPUT04 AUTO AUTO =CONTROL BY PANEL
5=OUTPUT05 AUTO MAN ON =OVERRIDE IN ON POSITION BY OPERATOR
6=OUTPUT06 AUTO MAN OFF=OVERRIDE IN OFF POSITION BY OPERATOR
7=OUTPUT07 AUTO ********************************************
8=OUTPUT08 AUTO
9=EXPANSION BOARD OUTPUTS
0=RETURN TO SETUP MENU
I=RETURN TO MAIN MENU
SELECT A NUMBER:9
OVERRIDE OUTPUT
Manually override
an output point
Select output to override
OUTPUT CONTROL
1=OUTPUT09 AUTO
2=OUTPUT10 AUTO
3=OUTPUT11 AUTO ********************************************
4=OUTPUT12 AUTO AUTO =CONTROL BY PANEL
5=OUTPUT13 AUTO MAN ON =OVERRIDE IN ON POSITION BY OPERATOR
6=OUTPUT14 AUTO MAN OFF=OVERRIDE IN OFF POSITION BY OPERATOR
7=OUTPUT15 AUTO ********************************************
8=OUTPUT16 AUTO
9=RETURN TO SETUP MENU
0=RETURN TO MAIN MENU
SELECT A NUMBER:1
>OVERRIDE OUTPUT OUTPUT09-AUTO(2),MAN ON(1),MAN OFF(0).
>[2]
>[
>COMMAND SUCCESSFUL
Setup Menu
130
A.6.10 Clear Alarms & Logs
For details on this topic, see 9.12 - Clear Alarms & Logs.
Clear Active Alarms
For details on this feature, see 9.12.1 - Clear Active Alarms.
Clear the Alarm Log
For details on this feature, see 9.12.2 - Clear the Alarm Log.
Clear Alarms & Logs - Clear Active Alarms
CLEAR ALARMS&LOGS
Clear active alarms
or log records
Select the log to clear
1=CLEAR ACTIVE ALARMS
2=CLEAR ALARM LOG
3=CLEAR EVENT LOG
4=CLEAR TREND LOGS
5=RETURN TO SETUP MENU
6=RETURN TO MAIN MENU
SELECT A NUMBER:1
>CLEAR ALL THE ACTIVE ALARMS-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
Clear Alarms & Logs - Clear the Alarm Log
CLEAR ALARMS&LOGS
Clear active alarms
or log records
Select the log to clear
1=CLEAR ACTIVE ALARMS
2=CLEAR ALARM LOG
3=CLEAR EVENT LOG
4=CLEAR TREND LOGS
5=RETURN TO SETUP MENU
6=RETURN TO MAIN MENU
SELECT A NUMBER:2
>CLEAR ALL RECORDS IN THE ALARM LOG-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
Setup Menu
131
Clear the Event Log
For details on this feature, see 9.12.3 - Clear the Event Log.
Clear the Trend Logs
For details on this feature, see 9.12.4 - Clear the Trend Logs.
Clear Alarms & Logs - Clear the Event Log
CLEAR ALARMS&LOGS
Clear active alarms
or log records
Select the log to clear
1=CLEAR ACTIVE ALARMS
2=CLEAR ALARM LOG
3=CLEAR EVENT LOG
4=CLEAR TREND LOGS
5=RETURN TO SETUP MENU
6=RETURN TO MAIN MENU
SELECT A NUMBER:3
>CLEAR ALL RECORDS IN THE EVENT LOG-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
Clear Alarms & Logs - Clear the Trend Logs
CLEAR ALARMS&LOGS
Clear active alarms
or log records
Select the log to clear
1=CLEAR ACTIVE ALARMS
2=CLEAR ALARM LOG
3=CLEAR EVENT LOG
4=CLEAR TREND LOGS
5=RETURN TO SETUP MENU
6=RETURN TO MAIN MENU
SELECT A NUMBER:4
>CLEAR ALL RECORDS IN THE TREND LOGS-YES(Y) OR NO(N)?
>[N]
>[
>COMMAND SUCCESSFUL
Default Settings Quick Reference Guide
132
APPENDIX B- DEFAULT SETTINGS QUICK REFERENCE GUIDE
This appendix provides a quick reference to default settings for the Universal Monitor and the
optional Expansion Board. These settings also appear throughout the manual.
Table 37 Universal Monitor - default settings for inputs and outputs
DEFAULT SETTINGS - DIGITAL INPUTS (FROM TABLE 21)
Feature Default Other Options
LABEL INPUT_01 - INPUT_08 Any name (up to eight characters)
NORM OPEN/CLOSE NO (Normally open) NC (Normally closed)
ALARM/EVENT AL (Alarmable) EV (Event)
LATCHED NL (Unlatched) / N (No)* L (Latched) / Y (Yes)*
DELAY 00:01 (1 second) Any time (in minutes and seconds) from 00:00 to 99:59
* NOTE: Different abbreviations are used to designate a digital input as Latched or Unlatched.
DEFAULT SETTINGS - ANALOG SENSOR INPUTS (FROM TABLE 22)
Feature Default Other Options
CONNECTED* N (Not connected)* Y (Connected)**
LABEL SENSOR_1 - SENSOR_4 Any name (up to eight characters)
UNITS Blank Any units (up to three characters)
4 mA -999.9 Can define up to two decimal places—e.g., -99.99
20 mA +999.9 Can define up to two decimal places—e.g., +99.99
OFFSET +000.0 Can define up to two decimal places—e.g., +00.00
ALARM/EVENT AL (Alarmable) EV (Event)
LATCHED N (Unlatched) Y (Latched)
LOW SETPT -0999.9 Can define up to two decimal places—e.g., -999.99
HIGH SETPT +0999.9 Can define up to two decimal places—e.g., +999.99
SENSOR DELAY 00:01 (1 second) Any time (in minutes and seconds) from 00:00 to 99:59
* If a sensor is configured as N (Not connected), the display will show an empty reading (blank spaces).
** If a sensor is configured as Y (Connected) and is functioning properly, the display will show a reading.
If the connected sensor is not functioning properly, the display will show dashes (------) indicating a problem.
DEFAULT MAPPING OF DIGITAL INPUTS TO DIGITAL OUTPUTS (FROM TABLE 23)
Digital input By default, mapped to digital output:
Input_01 Output01
Input_02 Output02
Input_03 Output03
Input_04 Output04
Input_05 Output05
Input_06 Output06
Input_07 Output07
Input_08 Output08
DEFAULT MAPPING OF ANALOG INPUTS TO DIGITAL OUTPUTS (FROM TABLE 24)
Analog input By default, mapped to digital output:
Sensor_1 (none)
Sensor_2 (none)
Sensor_3 (none)
Sensor_4 (none)
DEFAULT SETTINGS - DIGITAL OUTPUTS (FROM TABLE 25)
Feature Default Other Options
LABEL OUTPUT01 - OUTPUT08 Any name (up to eight characters)
NORM OPEN/CLOSE NO (Normally open) NC (Normally closed)
Default Settings Quick Reference Guide
133
Table 38 Universal Monitor - other default settings
JUMPER SETTINGS
Feature Default Other Options
Digital output loss-of-power jumpers OFF - Normally Open ON - Normally Closed
Note: Jumper position has no effect when the Universal Monitor has power.
12VDC/24VDC analog input jumper 24VDC Acceptable voltage for all four two-wire analog sensors
P20 jumper Not jumpered (not
connected) —
422 TERM jumper Default: jumpered
(connected) —
485 TERM jumper Default: jumpered
(connected) —
Audible horn Enabled May be disabled via the audible horn jumper
Manual Override switch Off (outputs controlled by
programming) On (Turn on all output relays)
DEFAULT SETTINGS - MODEM (FROM TABLE 27)
Feature Default Other Options
Initialization String (Init String) ATS0=1
Any string (up to 40 characters); for international
dialing, add +GCI=xx, where xx is the country code
(except B5 countries—see Table 27)
Enable Modem Diagnostic Messages N (disable) Y (enable)
Modem Dial Prefix ATE0X4DT Any string
Modem Hang Up Delay After a Call 10 seconds Any number (up to 99 seconds)
DIP SWITCH SETTINGS
Feature Default Other Options
8-position DIP switch All are OFF (down) May be used to reset password to factory default (see
9.9.1 - Change Password)
OTHER SETTINGS
Feature Default Other Options
Change state of outputs - automatic
or manual control AUTO (automatic control) Force an output ON / OFF via Manual Output Ctrl menu
Force all outputs ON via hardware switch
Password AAAA Any 4 characters (see Table 20 for valid characters)
Reset common alarm with silence N (not reset) Y (reset with silence)
Battery connected Y (connected) N (not connected)
Default Settings Quick Reference Guide
134
Table 39 Expansion Board - default settings for inputs and outputs
DEFAULT SETTINGS - DIGITAL INPUTS (FROM TABLE 21)
Feature Default Other Options
LABEL INPUT_09 - INPUT_24 Any name (up to eight characters)
NORM OPEN/CLOSE NO (Normally open) NC (Normally closed)
ALARM/EVENT AL (Alarmable) EV (Event)
LATCHED NL (Unlatched) / N (No)* L (Latched) / Y (Yes)*
DELAY 00:01 (1 second) Any time (in minutes and seconds) from 00:00 to 99:59
* NOTE: Different abbreviations are used to designate a digital input as Latched or Unlatched.
DEFAULT MAPPING OF DIGITAL INPUTS TO DIGITAL OUTPUTS (FROM TABLE 23)
Digital input By default, mapped to digital output:
Input_09 (none)
Input_10 (none)
Input_11 (none)
.
.
.(none)
Input_24 (none)
NOTE: By default, no Expansion Board inputs are mapped to any outputs.
DEFAULT SETTINGS - DIGITAL OUTPUTS (FROM TABLE 25)
Feature Default Other Options
LABEL OUTPUT09 - OUTPUT16 Any name (up to eight characters)
Table 40 Expansion Board - other default settings
CONNECTION TO UNIVERSAL MONITOR (see 9.10 - Setup Exp Board - Optional Expansion Board)
Feature Default Other Options
SETUP EXP BOARD (IS THE
EXPANSION BOARD
CONNECTED?)
N (Not connected) Y (Connected)
DIP SWITCH SETTINGS
Feature Default Other Options
S1 Digital output DIP switches Off (NO - Normally Open) On (NC - Normally Closed)
OTHER SWITCH SETTINGS
Feature
Default
For all switches:
1 = ON, 0 = OFF
Other Options
SW1 (factory configured) 11111111 —
SW2 (factory configured) 11111111 —
SW3 (factory configured) 10000100 —
SW4 (factory configured) 10000100 —
JUMPER SETTINGS
Feature Default Other Options
JP2 (factory configured) Left two pins jumpered —
JP3 (factory configured) Left two pins jumpered —
JP4 (factory configured) Left two pins jumpered —
JP5 (factory configured) Bottom two pins jumpered —
The Company Behind the Products
With over a million installations around the globe,
Liebert is the world leader in computer protection
systems. Since its founding in 1965, Liebert has
developed a complete range of support and
protection systems for sensitive electronics:
• Environmental systems—close-control air
conditioning from 1 to 60 tons
• Power conditioning and UPS with power
ranges from 300 VA to more than 1000 kVA
• Integrated systems that provide both
environmental and power protection in a
single, flexible package
• Monitoring and control—from systems of any
size or location, on-site or remote
• Service and support through more than 100
service centers around the world and a 24/7
Customer Response Center
While every precaution has been taken to ensure
the accuracy and completeness of this literature,
Liebert Corporation assumes no responsibility and
disclaims all liability for damages resulting from
use of this information or for any errors or
omissions.
© 2004 Liebert Corporation
All rights reserved throughout the world.
Specifications subject to change without notice.
® Liebert and the Liebert logo are registered
trademarks of Liebert Corporation. All names
referred to are trademarks or registered
trademarks of their respective owners.
SL-31060 (8/04) Rev. 1
Technical Support/Service
Web Site
www.liebert.com
Monitoring
800-222-5877
monitoring@liebert.com
Outside the US: 614-841-6755
Single-Phase UPS
800-222-5877
upstech@liebert.com
Outside the US: 614-841-6755
Three-Phase UPS
800-543-2378
powertech@liebert.com
Environmental Systems
800-543-2778
Outside the United States
614-888-0246
Locations
United States
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Italy
Via Leonardo Da Vinci 8
Zona Industriale Tognana
35028 Piove Di Sacco (PD)
+39 049 9719 111
Fax: +39 049 5841 257
Asia
23F, Allied Kajima Bldg.
138 Gloucester Road
Wanchai
Hong Kong
+852 2 572 2201
Fax: +852 2 831 0114
MONITORING
UNIVERSAL MONITOR
USER MANUAL

Navigation menu