Lifestyler 831159330 User Manual SYSTEM CXT Manuals And Guides L1005356

User Manual: Lifestyler 831159330 831159330 LIFESTYLER LIFESTYLER SYSTEM CXT - Manuals and Guides View the owners manual for your LIFESTYLER LIFESTYLER SYSTEM CXT #831159330. Home:Fitness Equipment Parts:Lifestyler Parts:Lifestyler LIFESTYLER SYSTEM CXT Manual

Open the PDF directly: View PDF .
Page Count: 24

Download
Open PDF In Browser	View PDF

8EAIRS"
Model No. 831.159330
Serial No.
The serial number can be found
in the location shown below.
Write the serial number in the
space above.

COMPACT
35+
200

TRAINING

SYSTEM

EXERCISES
LBS

CAST

IRON

Serial Number

CAUTION!
Read all safety precautions and Instructions
In this owner's

manual

and in the accompanyIng literature

before

using this equipment.
Keep this owner's

man-

ual In a safe place
future reference.

for

0 WNER 'S MAN UAL

TABLE OF CONTENTS
IMPORTANT

SAFETY

PRECAUTIONS

.................................................

2

BEFORE YOU BEGIN ...............................................................
ASSEMBLY .......................................................................
CABLE DIAGRAMS
................................................................
USING THE COMPACT TRAINING SYSTEM
...........................................
TROUBLE-SHOOTING
AND MAINTENANCE
...........................................
ORDERING
REPLACEMENT
PARTS ..........................................
WARRANTY
..............................................................

3
4
19
21
23
Back Cover
Back Cover

IMPORTANT SAFETY PRECAUTIONS
WARNING: To reduce the risk of serious Injury, read the following Important safety precautions
before using the compact training system.
1. Read all Instructions in this owner's manual and In the accompanying literature before using
the compact training system. Use the compact training system only as described.
2.

Inspect and properly tighten all parts of the compact training system each time you exercise. Replace any worn parts Immediately.

3.

Keep your hands away from moving parts other than the designated handles. Always wear
athletic shoes for foot protection.

4.

Keep small children away from the compact training system at all times.

5.

Never release the butterfly arms, leg lever, military press arm, bench press arm, leg press
plate, lat bar or strap while weights are raised. The weights will fall with great force.

6.

Make sure that the cables remain on the pulleys as you use the compact training system.

7. When attaching the seat bracket to the compact training system, make sure that the seat
bracket Is fully seated on the clevis pin.
8.

If you feel pain or dizziness
Ing down.

at any time while exercising,

stop Immediately

and begin cool-

WARNING:
Before beginning this or any exercise program, consult your physician.
This Is
especially
Important for persons over the age of 35 or persons with pre-existing
health problems. Read all Instructions
before using this product. SEARS assumes no responsibility
for per2

sonal Injury or property

damage

sustained

by or through

the use of this product.

BEFORE YOU BEGIN
Congratulations for selecting the SEARS LIFESTYLER ®SYSTEM CXT compact training system. The
innovative LIFESTYLER SYSTEM CXT offers an impressive array of weight training exercises to let
you develop every major muscle group of the body. Whether your goal is improved cardiovascular fitness, a shapely, toned body or dramatic muscle size and strength, the LIFESTYLER SYSTEM CXT will
help you to achieve the specific results you want.
For your safety and benefit,

read this owner's

manual

and the accompanying

literature

before

using the LIFESTYLER
SYSTEM CXT. If you have additional questions, please call our Customer
Service Department toll-free at 1-800-999-3756,
Monday through Friday, 6 a.m. until 6 p.m. Mountain
Time (excluding holidays), To help us assist you, please note the product model number and serial
number before calling. The model number is 831.159330.
The serial number can be found on a decal
attached to the LIFESTYLER
SYSTEM CXT (see the front cover of this owner's manual for the location
of the decal).

Before reading further, please examine the drawing below and familiarize yourself with the parts that
are labeled.

High Pulley

Military Press Arm
Mid Pulley

Bench Press Arm
ANTIS

Leg Press

Seat Bracket

Low Pulley

Leg Lever

Weights

ASSEMBLY
Assembly requires two people and will take about four hours. Due to the weight of the compact training
system, it should be assembled in the place where it will be used. Place all parts of the compact training system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. As you assemble the compact training system, read each step and
examine each drawing carefully. Make sure that all parts are oriented as shown In the drawings.
Refer to the PART CHART accompanying this owner's manual for help identifying the small parts used
in assembly.
The following tools (not Included) are required for assembly: two 8" adjustable wrenches, two
hammers and a phillips screwdriver. Grease and a small bowl of soapy water are also required.
.

Press four 2' Square Caps (65) into the Base
(19).
Insert the six 3/8' x 2 1/2' Carriage Bolts (14)
up through the indicated holes in the Base
(19). Finger tighten six 3/8" Nuts (5) onto the
Carriage Bolts. Lay the Base on the floor as
shown. Remove the Nuts from the Carriage
Bolts.

.

Press one 2" Square Cap (65) and one 1 1/2"
Square Cap (63) into the Press Frame (20).
Slide the Press Frame (20) onto the two indicated 3/8" x 2 1/2" Carriage Bolts (14) in the
Base (19). Attach the Press Frame with two
3/8' Lock Washers (15) and 3/8" Nuts (5).
Make sure that the heads of the Carriage
Bolts are flush against the Base.

4

5

5

65

,

°

Slide one end of the 265' Cable (54) onto a
3/8" x 2' Bolt (9). (The 265" Cable is the long
Cable that has an eyelet on one end, and is
threaded on the other end.) Slide a Cable
Trap (3) and a Small Pulley (1) onto the Bolt.
Insert the Bolt through the indicated bracket
on the Press Frame (20) and tighten a 3/8'
Nylock Nut (4) onto the Bolt. IMPORTANT:
As you attach each of the Pulleys In
assembly steps 3-43, be careful not to
overUghten the Nylock Nuts.

Press two I 3/4" Round Caps (67) into the
upper end of the Bench Press Arm (21).

20

4

67

Insert a Handle (76) into one side of the Bench
Press Arm (21). Tum the Handle so the small
hole near the end of the Handle is aligned
with the hole in the Bench Press Arm. Attach
the Handle with a 3/4" Screw (75).

67

Attach a Handle (76) to the other side of the
Bench Press Arm (21) in the same manner.
Wet both Handles (76) with soapy water.
Slide a Grip (46) onto each Handle.
I1_,/

,t-'J

I1(.,

•

Irl_._[l_

'

k/O_/

_UU/

UI

ILU

UI

I€

€1

IU

Grease

UI

the 1/2" x 10" Axle (58). Apply a small
amount of grease to the Axle. Align the lower
end of the Bench Press Arm (21) with the
indicated tube on the Base (19). Insert the
Axle through the Bench Press Arm and the
Base. While holding one hammer against the
1/2" Plastic Cap (68) on the Axle, tap another
1/2" Plastic Cap (68) onto the Axle.

=

Press the two 1 3/4" Square Caps (64) into
the Leg Press Lever (22).
Press two 3/4" Bushings (18) into the indicated bracket on the Base (19).
Tap a 3/4" Plastic Cap (69) onto one end of the
3/4" x 3 1/2" Axle (59). Apply a small amount of
grease to the Axle. Align the lower end of the
Leg Press Lever (22) with the bracket on the
Base (19). Insert the Axle through the Leg
Press Lever and the 3/4" Bushings (18) in the
Base. While holding one hammer against the
3/4' Plastic Cap (69) on the Axle, tap another
3/4" Plastic Cap (69) onto the Axle.

58

5
64

69

Grease

6. Slide a Cable Trap (3) and a Small Pulley (1)

6

onto a 3/8" x 4 1/2" Bolt (13). Route the 265"
Cable (54) up around the Small Pulley. Make
sure that the Cable is between the Cable

22

Trap and the Small Pulley.
Insert the 3/8" x 4 1/2" Bolt (13) through the
indicated hole in the Leg Press Lever (22).
Finger tighten a 3/4" Nylock Nut (4) onto the
Bolt.

13
o

Slide a Cable Trap (3) and a Small Pulley (1)

7

onto a 3/8" x 5" Bolt (77). Route the 265"
Cable (54) down around the Small Pulley.
Make sure that the Cable is between the
Cable Trap and the Small Pulley.
44

Hold the "U" Bracket (44) inside the opening
in the Press Frame (20). Insert the 3/8" x

77

5" Bolt (77) through the indicated hole in
the Press Frame. The Bolt should hold the
"U" Bracket in the Press Frame. Finger tighten a 3/4" Nylock Nut (4) onto the Bolt.

.

Slide a Cable Trap (3) and a Small Pulley (1)
onto a 3/8" x 2" Bolt f9_. Route the 265"

8

II. s, Ill

Cable (54) up around the Small Pulley. Make
sure that the Cable is between the Cable
Trap and the Small Pulley.
Insert the 3/8" x 2" Bolt (9) through the indicated bracket on the Bench Press Arm (21).
Tighten a 3/8" Nylock Nut (4) onto the Bolt.

°

Route the 265" Cable (54) through the "U"
Bracket (44) in the Press Frame (20). Attach
a Small Pulley (1) to the "U" Bracket with a
3/8" x 2" Bolt (9) and 3/8" Nylock

Nut (4).

9
\
\

\
\
\\

6

10. Slide
onto
(54)
sure

a Cable Trap (3) and a Small Pulley (1)
a 3/8" x 2" Bolt (9). Route the 265" Cable
down around the Small Pulley. Make
that the Cable is between the Cable

Trap and the Small

10

Pulley.

Insert the 3/8" x 2" Bolt (9) through the indicated bracket on the Bench Press Arm (21).
Tighten a 3/8" Nylock Nut (4) onto the Bolt.

11. Remove the 3/8" Nylock Nut (4) from the indicated 3/8" x 5" Bolt (77). (This is the Bolt

11

that was used in assembly step 7.) Slide a
Small Pulley (1) and a Cable Trap (3) onto the
Bolt. Route the 265" Cable (54) up around the
Small Pulley. Make sure that the Cable is
between the Cable Trap and the Small Pulley.
Tighten the 3/8" Nylock Nut (4) onto the Bolt.

77
\

1

12. Remove the 3/8" Nylock Nut (4) from the indicated 3/8" x 4 1/2" Bolt (13_. (This is the Bolt
that was used in assembly step 6.) Slide a
Small Pulley (1) and a Cable Trap (3) onto the
Bolt. Route the 265" Cable (54) down around
the Small Pulley. Make sure that the Cable is
between the Cable Trap and the Small Pulley.
Tighten the 3/8" Nylock Nut (4) onto the Bolt.

12

13. Loosen the 3/8" Nylock Nut (4) on the indicated 3/8" x 2" Bolt (9). Route the 265" Cable
(54) around the Small Pulley (1). Make sure

13

4

i/ll

that the Cable is between the Cable Trap (3)
and the Small Pulley. Tighten the 3/8" Nylock
Nut.
Route
cated
Small
1 3/4"

the 265" Cable (54) through the indibracket on the Base (19). Attach a
Pulley (1) to the bracket with a 3/8" x
Bolt (8) and 3/8" Nylock Nut (4).

54

14. Attach a Seat (39) to the Press Frame (20)
with two 1/4" x 3/4" Bolts (6).

14

Snap the plastic pin on the lower end of the
Large Backrest (37) into the lower hole in the
Press Frame (20). Attach the upper end of the
Large Backrest to the Frame with a 1/4" x
2 1/2" Bolt (7).

15. Slide the Leg Press Plate (23) onto the Leg
Press Lever (22) as shown. Align the tubes
on the Leg Press Plate with one of the four
holes in the Leg Press Lever. Insert the 8" "L"
Pin (42) through the Leg Press Plate and the
Leg Press Lever.

20

15
22

42

\

23

16. Slide the Weight Upright (31) onto the two
indicated 3/8' x 2 1/2" Carriage Bolts (14) in
the Base (19). Attach the Weight Upright with
two 3/8" Lock Washers (15) and 3/8" Nuts (5).
Make sure that the heads of the Carriage
Bolts are flush against the Base. Do not fully
tighten the Nuts yet.

16

19

8

7

17. Slide the four Bumpers
Weight

Guides

(45) onto the four

17

(34).

4
4

Insert the Weight Guides (34) into the indicated holes in the Base (19). Attach the upper
ends of the Weight Guides to the brackets on
the Weight Upright (31) with 3/8" x 1 3/4"
Bolts (8) and 3/8" Nylock Nuts (4). Attach the
lower end of the indicated Weight Guide to
the Base with a 3/8" x 2 3/4" Bolt (10) and
3/8" Nylock Nut (4).
Tighten the 3/8" Nuts (5) at the lower end of
the Weight Upright (31).

18. Slide a 3/8" Flat Washer (16) and a Spacer
(62) onto a 3/8" x 2 3/4" Bolt (10_.
Insert the 265" Cable (54) up
Weight Upright (31) and over
(2) as shown. Hold the Large
the Weight Upright. Insert the

18

through the
a Large Pulley
Pulley inside
3/8" x 2 3/4" Bolt

62
16

(10) through the Weight Upright and the
Large Pulley. Slide a Spacer (62) and 3/8"
Flat Washer (16) onto the Bolt. Tighten a 3/8"
Nylock Nut (4) onto the Bolt.

19. Thread the end of the 265" Cable (54) into
one of the Weight Tubes (35) until about half
of the threads are inside of the Weight Tube.

10

19
54

Thread the end of the 125" Cable (52) into the
other Weight Tube (35) in the same manner.
Press a Weight Tube Cap (36) into the lower
end of each Weight Tube (35).

9

20. Slide

a 3/8" Flat Washer (16), one end of the
17" Cable (51) and a Spacer (62) onto a 3/8"
x 2 3/4" Bolt (10).

20

31

Insert the 125" Cable (52) up through the
Weight Upright (31) and over a Large Pulley
(2) as shown. Hold the Large Pulley inside
the Weight Upright. Insert the 3/8" x 2 3/4"
Bolt (10) through the Weight Upright and the
Large Pulley. Slide a Spacer (62) and 3/8"
Flat Washer (16) onto the Bolt. Tighten a 3/8"
Nyiock Nut (4) onto the Bolt.

21. Press a 2" Square Cap (65) into the Military

Press Lever (33).
Press two 1/2" Bushings (17) into the indicat-

21
33
\

Tap a 1/2" Plastic Cap (68) onto one end of
the 112" x 3 1/2" Axle (57). Apply a small
amount of grease to the Axle. Align the end
of the Military Press Lever (33) with the
bracket on the Weight Upright (31). Insert the
Axle through the Weight Upright and the 1/2"
Bushings (17) in the Military Press Lever.
While holding one hammer against the 1/2"
Plastic Cap (68) on the Axle, tap another
Plastic Cap (68) onto the Axle.

!3t
17
57

Grease ,_
68

1/2"

22. Attach two Small Pulleys (1) to the two "1"
Plates (43) with 3/8" x I 3/4" Bolts (8) and
3/8" Nylock Nuts (4). Make sure that the Bolts
are through the holes in the ends of the "1"
Plates.

22

43

10

23. Insert the 125" Cable (52) through the "1"
Plates (43). The ends of the "1"Plates with
the three holes should be downward.

23

Slide a Cable Trap (3) and a Small Pulley (1)
onto a 3/8" x 4" Bolt (12). Route the 125"
Cable (52) over the Small Pulley. Make sure
that the Cable is between the Cable Trap and
the Small Pulley.
Insert the 3/8" x 4" Bolt (12) through the indicated hole in the Military Press Lever (33).
Slide the end of the 17" Cable (51) and a 3/8"
Flat Washer (16) onto the Bolt. 13ghten a 3/8"
Nylock Nut (4) onto the Bolt.

24
11

24. Lay the 125" Cable (52) over a Small Pulley
(1). Attach the Small Pulley to the end of the
Military Press Lever (33) with a 3/8" x 3 1/2"
Bolt (11) and 3/8" Nylock Nut (4). Make sure
that the Cable Is between the Indicated

Pin

pin and the Small Pulley.

25. Press two 1 3/4" Round Caps (67) into the
lower end of the Military Press Arm (32).

52

1

33

25

Aiiuch ihe Press
Arm using this hole

Insert a Handle (76) into one side of the
Military Press Arm (32). Turn the Handle so
the small hole near the end of the Handle is

16

aligned with the hole in the Military Press Arm.
Attach the Handle with a 3/4" Screw (75).

<

41

s. o

10

Attach a Handle (76) to the other side of the
Military Press Arm (32) in the same manner.
Wet both Handles (76) with soapy water.
Slide a Grip (46) onto each Handle.

46

Attach the Military Press Arm (32) to the Military Press Lever (33) with a 3/8" x 2 3/4" Bolt
(10), two 3/8" Flat Washes (16) and a 3/8"
Nylock Nut (4). Make sure that the Bolt is
inserted through the indicated holes, and that
the Flat Washers are between the Military
Press Arm and the Military Press Lever.

Pivot the Military Press Arm (32) until one of
the holes in the Military Press Arm is aligned
with the hole in the Military Press Lever (33).
Insert the 4 1/4" "L' Pin (41) through the Military
Press Arm and the Military Press Lever.

76
67

67

46

11

26. Route the 258" Cable (53) under a Small
Pulley (1). Attach the Small Pulley to the
lower end of the Weight Upright (31) with a
3/8" x 3 1/2" Bolt (11) and3/8"
Nylock Nut (4).
Make sure that the Cable Is between the
Indicated

26

pin and the Small Pulley.

27. Insert the 258" Cable (53) through the "1"
Plates (43) as shown.
Route the 258" Cable (53) under a Small
Pulley (1). Attach the Small Pulley to the indicated bracket on the Base (19) with a 3/8" x
1 3/4" Bolt (8) and 3/8" Nylock

Nut (4).

19
28. Route
r.ntnd
Small
1 3/4"

12

the 258" Cable (53) through the indihrnr.k_.t nn the. Rn.qA (19). Attach a
Pulley (1) to the bracket with a 3/8" x
Bolt (8) and 3/8" Nylock Nut (4).

28

29. Attach the Small Backrest (38) to the Weight
Upright (31) with two 1/4" x 2 1/2" Bolts (7).

29

II IIIrlll

30. Insert the Clevis Pin (60) through one of the
three holes in the Weight Upright (31). Insert
the Hairpin Cotter (61) through the Clevis Pin.
Note: The Clevis Pin is very similar to the Leg
Lever Axle (not shown). If the Hairpin Cotter
does not fit, then you have mistaken the Leg
Lever Axle for the Clevis Pin.
Press a 1 1/2" Square Cap (63) into the Seat
Bracket (30).
Attach a Seat (39) to the Seat Bracket (30)
with two 1/4" x 3/4" Bolts (6). Slide the Seat
Bracket onto the Clevis Pin (60). WARNING"
Make sure that the Seat Bracket Is fully
seated on the Clevis Pin.
31. Press one 2" Square Cap (65) and three
1 1/2" Square Caps (63) into the Butterfly
Frame (24).

30

/

6

63

J_

Slide the Butterfly Frame (24) onto the two
indicated 3/8" x 2 1/2" Carriage Bolts (14) in
the Base (19). Attach the Butterfly Frame with
two 3/8" Lock Washers (15) and 3/8" Nuts
(5). Make sure that the heads of the Carriage
Bolts are flush against the Base.
32. Align the upper end of the Leg Lever (28)
with the indicated hole in the Butterfly Frame
(24). Insert the Leg Lever Axle (56) through
the Leg Lever and the Butterfly Frame. While
holding one hammer against the Leg Lever
Axle, tap the 1/2" Hat Cap (55) onto the Leg
Lever Axle.

24

15

IIIrlll

I/I
24

33. Slide a Cable Trap (3) and a Small Pulley (1)
onto a 3/8" x 4" Bolt (12). Route the 258"
Cable (53) up around the Small Pulley. Make
sure that the Cable is between the Cable
Trap and the Small Pulley.

53

Insert the 3/8" x 4" Bolt (12) through the indicated hole in the Butterfly Frame (24).
Tighten a 3/8" Nylock Nut (4) onto the Bolt.

3

4

24
13

4.

Slide a Cable Trap (3) and a Small Pulley (1)
onto a 3/8" x 2" Bolt (9). Route the 258" Cable
(53) over the Small Pulley. Make sure that the
Cable is between the Cable Trap and the
Small Pulley.

24
4

Insert the 3/8" x 2" Bolt (9) through the indicated bracket on the Butterfly Frame (24).
Tighten a 3/8" Nylock Nut (4) onto the Bolt.

35. Press four 3/4" Bushings
Butterfly

(18) into the

35

Frame (24) as shown.

Apply a small amount of grease to the pin on
the lower end of the Left Butterfly Arm (25).
Insert the pin through the 3/4" Bushings (18)
in the Butterfly Frame (24). Make sure that the
tab is on the side shown. Tap a 3/4" Plastic
Cap (69) onto the pin.

_;_--66

Attach the Right Butterfly Arm (26) to the
Butterfly Frame (24) in the same manner.
Wet the upper ends of the Butterfly Arms (25,
26) with soapy water. Slide a Large Pad (27)
onto each Buttediy Arm.
Press the 1 1/2" Round Caps (66) into the
upper ends of the Butterfly Arms (25, 26).

O-_69

36. Slide a Cable Trap (3) and a Small Pulley (1)

onto a 3/8" x 2" Bolt (9). Route the 258" Cable
(53) around the Small Pulley. Make sure that
the Cable is between the Cable Trap and the
Small Pulley.
Insert the 3/8" x 2" Bolt (9) through the indicated bracket on the Left Butterfly Arm (25).
Tighten a 3/8" Nylock Nut (4) onto the Bolt.

14

37. Route the 258" Cable (53) around a Small
Pulley (1). Attach the Small Pulley to the
Butterfly Frame (24) with a 3/8" x 1 3/4" Bolt
(8) and 3/8" Nylock Nut (4). Make sure that
the Bolt is through the indicated hole.

53
8

38. Slide a Cable Trap (3) and a Small Pulley (1)
onto a 3/8" x 2" Bolt (9). Route the 258" Cable
(53) around the Small Pulley. Make sure that
the Cable is between the Cable Trap and the
Small Pulley.
Insert the 3/8" x 2" Bolt (9) through the indicated bracket on the Right Butterfly Arm (26).
Tighten a 3/8" Nylock Nut (4) onto the Bolt.

39. Slide a Cable Trap (3) and a Small Pulley (1)
onto _ _/R" x 2" Bolt (.q). Route the 258" Cable
(53) down around the Small Pulley. Make
sure that the Cable is between the Cable

Ilflll

II

Trap and the Small Pulley.
Insert the 3/8" x 2" Bolt (9) through the indicated bracket on the Butterfly Frame (24).
Tighten

a 3/8" Nylock

Nut (4) onto the Bolt.

3

24

40. Insert a 3/8" x 4" Bolt (12) through the indicated hole in the Butterfly Frame (24).

Slide a Small Pulley (1) and a Cable Trap (3)
onto the 3/8" x 4" Bolt (12). Route the 258"
Cable (53) down around the Small Pulley.
Make sure that the Cable is between the
Cable Trap and the Small Pulley. Tighten a
3/8" Nylock Nut (4) onto the Bolt.
/
/
/

15

41. Insert a 3/8" x 2 3/4" Bolt (10) through
indicated

the

hole in the Leg Lever (28).

Slide a Small Pulley (1) and a Cable Trap (3)
onto the 3/8" x 2 3/4" Bolt (10). Route the
258" Cable (53) up around the Small Pulley.
Make sure that the Cable is between the
Cable Trap and the Small Pulley. Tighten
3/8" Nylock Nut (4) onto the Bolt.

a

42. Insert a 3/8" x 4" Bolt (12) through the tube
on the Butterfly Frame (24).
Slide a Small Pulley (1) and a Cable Trap (3)
onto the 3/8" x 4" Bolt (12). Route the 258"
Cable (53) up around the Small Pulley. Make
sure that the Cable is between the Cable
Trap and the Small Pulley. Tighten
Nylock Nut (4) onto the Bolt.

a 3/8"

43. Route the 258" Cable (53) over a Small Pulley
(1). Attach the Small Pulley to the UDDer end
of the Butterfly Frame (24) with a 3/8" x 3 1/2"
Bolt (11) and 3/8" Nylock Nut (4). Make sure
that the Cable is between the indicated pin
and the Small Pulley.

44. Attach a Seat (39) to the Butterfly
with two 1/4" x 3/4" Bolts (6).

Frame (24)

Snap the plastic pin on the lower end of the
Large Backrest (37) into the lower hole in the
Butterfly Frame (24). Attach the upper end of
the Large Backrest to the Frame with a 1/4" x
2 1/2" Bolt (7).

16

24
J

45.

Insert one Pad Tube (71) through the
Butterfly Frame (24), and one Pad Tube
through the Leg Lever (28).

\

45

Wet the ends of the Pad Tubes (71) with
soapy water. Slide the four Small Pads (29)
onto the Pad Tubes.

29

46. Press two Weight Sleeves
the twenty Weights

(72) into each of

46

(40).

Slide ten Weights (40) onto each pair of
Weight Guides (34) by tipping the Weights
as shown. Make sure that all of the
Weights are turned so the pin grooves
are downward, and are on the Indicated
sides or the system will be damaged.
Press a Weight Center (74) into the top
Weight (40) on each stack of Weights.
Insert the two Weight Tubes (35) into the
stacks of Weights (40).

47.

_rooves

Make sure that all parts are properly tightened. Adjust the position of each cable trap so that
when the compact training system Is used the cables will not rub against the edges of the
cable trap. The use of all remaining parts will be explained in the USING THE COMPACT TRAINING SYSTEM section on pages 21 and 22 of this owner's manual.

48. Before using the compact training system, test the cables and pulleys. Pull the end of each cable a
few times to make sure that the cable moves smoothly over the pulleys. Move the butterfly arms,
leg lever, military press arm, bench press arm and leg press plate a few times. If one of the cables
does not move smoothly, locate and correct the problem before using the compact training system.
See the CABLE DIAGRAMS on pages 19 and 20 of this owner's manual to see how each cable
should be routed. IMPORTANT: If the cables are not properly routed, they may be damaged
when used with heavy weight.

17

49. Remove

the decals,

one at a time, from the decal sheet,

system in the locations

"CXT HIGH

shown in the drawing

and apply them to the compact training

below.

•HANDS

CLEAR"

•CXT MID PULLEY"
"CXT MILITARY
PRESS

"BUTTERFLY CXT"

STATION"

"PRESS ARM CXT"

"CXT LEG PRESS"

"LEG CURL CXT
LEG EXTENSION"

"CXT LOW PULLEY"

18

CABLE DIAGRAMS
The cable diagrams show the proper routes of the four cables on the compact training system. The
numbers indicate the order in which the cables are routed around the pulleys. Use the diagrams to
make sure that the four cables are assembled correctly.

17" Cable (51)

Note: The 17" cable prevents the
military press lever from being
raised higher than 7', 6 ", in order to
protect ceilings from damage. If the
ceiling above the compact training
system is sufficiently high, the 17"
cable may be removed.

125" Cable (52)

4

The end of the
125" cable is
attached to the
weight tube.

19

258" Cable

(53)

265" Cable (54)

1

\

7

One end of the
265' cable is
attached to the
bolt.

20

end of
the 265" cable
is attached to
the weight
tube.

USING THE COMPACT TRAINING SYSTEM
The instructions below describe how each part of the compact training system can be adjusted.

See

the EXERCISE GUIDE accompanying this owner's manual to see how the compact training system
should be set up for each individual exercise.
CHANGING

THE WEIGHT

SE'I'FING

The weight stack next to the Weight Upright (31)
is connected to the military press arm, butterfly
arms, leg lever, low cable, mid cable and high
cable. The other weight stack is connected to the
bench press arm and leg press plate. To select a
weight setting for either weight stack, insert a
7 1/2" "L"Pin (73) under one of the Weights (40).
Turn the end of the Pin downward. IMPORTANT:
When using the bench press arm, the weight
will be multiplied 1.5 times. When using the
leg press plate, the weight will be tripled.
Up to fifteen Weights (40) can be placed on either
weight stack. IMPORTANT: When moving
Weights from one weight stack to the other,
always leave a Weight with a Weight Center
(74) on top of each weight stack.
ADJUSTING

THE LEG PRESS

PLATE

The Leg Press Plate (23) can be adjusted to any
of four positions. To change the position, first
remove the 8" "L" Pin (42). Move the Leg Press
Plate forward or backward, and insert the "L" Pin
through the Leg Press Plate and one of the four

42

22

\

holes in the Leg Press Lever (22).

ATTACHING

THE SEAT BRACKET

To attach the Seat Bracket (30) to the Weight
Upright (31), slide the Seat Bracket onto the
Clevis Pin (60). IMPORTANT: Make sure that
the Seat Bracket Is fully seated on the Clevis
Pin. To adjust the height of the Seat Bracket,
remove the Hairpin Cotter (61) from the Clevis
Pin, move the Clevis Pin to a different hole in the
Weight Upright, and reattach the Hairpin Cotter.
There are three adjustment holes.
For certain exercises, the Seat Bracket (30) should
be lifted off the Clevis Pin (61) and set aside.

21

ADJUSTINGTHEMILITARYPRESSARM
33

For the MILITARY PRESS or REVERSE MILITARY PRESS exercises (see the EXERCISE
GUIDE), pivot the Military Press Arm (32) so the
hole labeled "B" is aligned with the hole in the
Military Press Lever (33), and insert the 4 1/4' "L"
Pin (41) through the Military Press Arm and the
Military Press Lever. For all other exercises, align
the hole labeled "A' with the hole in the Military
Press Lever, and insert the "L" Pin through the
Military Press Arm and the Military Press Lever.
A'n'ACHING
THE LAT BAR OR STRAP
LOW CABLE

32

TO THE

The Lat Bar (47) can be attached to the low cable
using the Chain (48) and the two Cable Clips
(50). The distance between the Lat Bar and the
low cable can be adjusted by attaching the Cable
Clips closer together or farther apart on the Chain.
For some exercises, the Lat Bar should be
attached directly to the low cable using one
Cable Clip.

50
47

The Strap (49) can be attached to the low cable
in the same manner.
A'n'ACHING

THE LAT BAR OR STRAP TO THE MID CABLE

OR THE HIGH CABLE

The lat bar or strap can be attached to the mid cable or the high cable in the same manner as the low
cable. (See A'I-I'ACHING THE LAT BAR OR STRAP TO THE LOW CABLE above.)

22

TROUBLE-SHOOTING

AND MAINTENANCE

Inspect and properly tighten all parts of the compact training system each time you exercise. Replace
any worn parts immediately. The compact training system can be cleaned using a damp cloth and mild
non-abrasive detergent. Do not use solvents.
ADJUSTING

THE CABLES

If there is too much slack in the cables, the
cables can be adjusted. To adjust the cables
attached to the weight stack next to the weight
upright, find the end of the 125" Cable (52). Turn
the end of the Cable clockwise to thread it farther
into the Weight Tube (35). To adjust the cables
attached to the other weight stack, find the end
of the 265' Cable (54). Turn the end of the Cable
clockwise to thread it farther into the Weight
Tube (35).

The cables attached to the weight stack next to
the weight upright can also be adjusted using the
two "1"Plates (43). Remove the 3/8" x 1 3/4" Bolt
(8) and 3/8" Nylock Nut (4) attaching the lower
Small Pulley (1) to the "1"Plates. Reattach the
Small Pulley to the '1" Plates using the next higher hole in the "1"Plates. Repeat until the cables
are propedy tightened.

23

ORDERING
Each COMPACT
NUMBER

REPLACEMENT

TRAINING

SYSTEM

when requesting

service

PARTS

has its own MODEL

NUMBER.

or repair parts for your COMPACT

Always

mention

TRAINING

this MODEL

SYSTEM.

All parts listed herein can be ordered through SEARS, ROEBUCK AND CO. SERVICE CENTERS and
most SEARS RETAIL STORES. If parts you need are not stocked locally, your order will be transmitted
to a SEARS PARTS DISTRIBUTION CENTER for handling.
WHEN

ORDERING

1. The MODEL

REPAIR

NUMBER

4. The DESCRIPTION
owner's manual.

ALWAYS

of the product

2. The NAME of the product
3. The PART NUMBER
owner's manual.

PARTS,

(SEARS

GIVE THE FOLLOWING

INFORMATION:

(831.1 59330).

LIFESTYLER

®SYSTEM

CXT compact

of the part(s) from the PART LIST/EXPLODED

of the part(s) from the PART LIST/EXPLODED

training

DRAWING

DRAWING

system).

accompanying

accompanying

this

this

Your SEARS merchandise has added value when you consider that SEARS has service units nationwide, staffed with SEARS trained technicians specifically trained on SEARS products, having the parts,
tools and equipment to ensure that we meet our pledge to you: "We service what we sell."
Should you ever need repair service or parts, call toll-free:
For repair service: 1-800-4-REPAIR

(1-800-473-7247)

For repair pArt_: 1-800-FON-PART

(1-RI313-_RR-7_TR)

FULL 90 DAY WARRANTY
For 90 days from the date of purchase, when proper assembly and maintenance procedures
detailed in the owner's manual are followed, SEARS will, free of charge, repair or replace and
install a replacement part for any defective part, when this compact training system is used in
a normal manner.
This warranty does not apply when this compact training system is used for commercial or
rental purposes.
SERVICE

IS AVAILABLE

CENTER/DEPARTMENT

SIMPLY

BY CONTACTING

IN THE UNITED

YOUR

NEAREST

SEARS

SERVICE

STATES.

This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
SEARS, ROEBUCK
AND CO., DEPT. 817WA,
3333 BEVERLY ROAD, HOFFMAN ESTATES, IL 60179

Part No. 113521 11/93 © Sears, Roebuck and Co.

Printed in USA



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 24
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Sat Mar 29 13:11:21 2014
Author                          : 
Title                           : 
Subject                         : 

EXIF Metadata provided by EXIF.tools