Liftmaster Csl24V Owners Manual USER GUIDE CSL24VH CSW24V CSW24VH

Liftmaster-Csw24V-Owners-Manual liftmaster-csw24v-owners-manual

: Liftmaster Liftmaster-Csl24V-Owners-Manual liftmaster-csl24v-owners-manual liftmaster pdf

Open the PDF directly: View PDF .
Page Count: 8

USER’S GUIDE

VEHICULAR SLIDE/SWING GATE OPERATORS

Your model may look different than the model illustrated in this user’s guide.

CSL24V ™ & CSL24VH ™ CSW24V ™ & CSW24VH ™

Installation Date

www.liftmaster.com

Please contact your authorized LiftMaster dealer

for all of your service needs.

1

RESET SWITCH/MANUAL DISCONNECT

The reset switch is located on the front of the operator and serves several functions. When referring to “toggling”

the reset switch it means pressing the reset switch to the RESET/DISCONNECT position, then back to the NORMAL

OPERATION position.

Toggling the reset switch will stop a moving gate during a normal open/close cycle, like a stop button. The operator

does not need to be reset after doing this. The reset switch will disable the gate in the present position and will

energize the solenoid lock for two minutes and disable the maglock for two minutes.

OPERATION

Thank you for purchasing a LiftMaster gate operator.

Our operators are designed to meet or exceed UL325

safety standards and requirements and are quality

manufactured for years of safe and reliable service.

Think LiftMaster for all of your Access Control needs.

MODEL CSL24V SLIDE GATE

OPERATOR

Press the reset switch to RESET/

DISCONNECT to allow the gate to be

opened and closed manually. To

resume normal operation press the

reset switch to NORMAL OPERATION.

MODEL CSW24V SWING GATE

OPERATOR

Press the reset switch to RESET/

DISCONNECT. Release the handle on

the operator arm to allow the gate to

be opened and closed manually. On a

dual gate application the handle must

be released on both operators. To

resume normal function tighten the

handle by pushing it down.

RESET/DISCONNECT

NORMAL OPERATION

Manual Disconnect

Handle

RESET/DISCONNECT

NORMAL OPERATION

2

REMOTE CONTROL

Once the remote control has been programmed operator will operate as follows:

When gate is in the closed position, activation of the remote control button will open the gate. During the open cycle

another activation of the remote control will stop the gate and the next activation of the remote control will close

the gate. When the gate is in the open position, activation of the remote control button will close the gate. If the

remote control is activated while the gate is closing, the gate will stop and the next activation will open the gate.

If a contact sensor detects an obstruction twice consecutively the alarm will sound

(up to 5 minutes) and the operator will need to be reset. If a command is given

after the initial 5 minutes the operator will beep.

The gate does not meet

specifications.

Debris is on the gate's track

such as mud, rocks, dirt, etc.

(Slide Only)

The gate has one or more

broken axles or wheels.

(Slide Only)

The gate wheel is off the gate

rail. (Slide Only)

The gate is hitting a wall or

vehicle.

Remove any obstructions. Toggle the reset switch to shut off the alarm and reset the operator. After the operator is

reset, normal functions will resume.

When the inherent force of the operator (RPM/current

sensor) detects the following (twice consecutively) the

alarm will sound (up to 5 minutes) and the operator

will need to be reset:

Gate hinges are too tight or

broken and the gate is not

moving freely. (Swing Only)

The gate is moving and a car

pushes the gate.

(Swing Only)

A foreign object is on the gate

frame while the gate is moving.

(Swing Only)

The gate hits the driveway, curb

or other, and gets stuck or bent

in an awkward position.

(Swing Only)

OPERATOR ALARM

The operator arm or gate is

incorrectly installed.

(Swing Only)

OPERATION

3

MAINTENANCE

The following should be checked by an authorized LiftMaster dealer:

BATTERIES

Batteries will degrade over time depending on temperature and usage. For best performance, the batteries should

be replaced every 3 years. Use only LiftMaster part 29-NP712 for replacement batteries. The operator comes with

two 7AH batteries. Two 33AH (A12330SGLPK) may be used in place of the 7AH batteries.

The batteries contain lead and need to be disposed of properly. Batteries do not perform well in extremely cold

temperatures.

NOTE:

If your application includes a heater, two 33AH will not fit into the operator enclosure (swing only).

The operator alarm will beep 3 times with a command if the battery is low.

DRIVE CHAIN (SLIDE ONLY)

Over time, the drive chain on the operator will stretch and need to be tightened. To tighten the drive chain adjust

either of the two chain eye bolts.

NOTE: The chain should have no more than 1 inch of sag for every 10 feet of chain length.

CHECK AT LEAST ONCE EVERY MONTH

DESCRIPTION TASK

Entrapment Protection Devices Check and test for proper operation

Warning Signs Make sure they are present

Gate Inspect for wear or damage

Drive Chain (Slide Only) Check for excessive slack and lubricate

CHECK AT LEAST ONCE EVERY

DESCRIPTION TASK 6 MONTHS 3 YEARS

Manual Disconnect Check and test for proper operation X

Sprockets and Chains Check for excessive slack and

lubricate

X

Belt and Pulley (Slide

Only)

Check for excessive slack, wear, or

damage

X

Accessories Check all for proper operation X

Electrical Inspect all wire connections X

Chassis Mounting Bolts Check for tightness X

Operator Inspect for wear or damage X

Batteries Replace X

4

ACCESSORIES

PHOTOELECTRIC SENSORS (NON-CONTACT)

The photoelectric sensors are designed to detect an obstacle in the path of the

electronic beam and stop the operator. Includes mounting brackets.

Models AOMRON E3K-R10K4-NR (retro-reflective), RETROAB 60-2728

(retro-reflective), CPS-UN4 (through beam)

ENTRAPMENT PROTECTION DEVICES

REMOTE CONTROLS

Chamberlain offers a variety of LiftMaster remote controls to satisfy your application needs. Single-button to

4-button, visor or key chain. The following remote controls are compatible with operators manufactured by

Chamberlain after 1993. Contact your authorized LiftMaster dealer for additional details and options.

3-BUTTON REMOTE CONTROL

The 3-button remote control can be programmed to control the operator. Includes

visor clip.

Model 893MAX

3-BUTTON MINI-REMOTE CONTROL

The 3-button remote control can be programmed to control the operator. Includes

key ring and fastening strip.

Model 890MAX

SENSING EDGE (2-WIRE, NON-MONITORED, CONTACT)

Sensing edges can detect an obstacle upon contact and stop the operator.

Models G65MG0204, G65MG0205, G65MGR205, and G65MGS205

SENSING EDGE CHANNEL

Mounting channel for all MG020 type edges.

Model G65ME120C5

KEYLESS ENTRY

Enables homeowner to operate gate operator from outside by entering a 4-digit

code on a specially designed keypad.

Model 877MAX

5

MISCELLANEOUS

REMOTE ANTENNA EXTENSION KIT

The remote antenna extension kit allows the antenna to be remotely installed.

Model 86LM

WIRELESS ACCESS CONTROL RECEIVER

Access control receiver for up to 450 remote controls.

Model STAR450-315

HEATER

Keeps operator, gearbox and batteries at suitable temperature when outside

temperature is below 0°F for extended periods of time.

Models HTRKITRSW (for Swing operator, includes bracket for optimal heater

location) and G6518CSW (Swing replacement heater only)

Models HTRKITRSL (for Slide operator, includes bracket for optimal 7AH battery

location) and G6518SL (replacement heater only)

LOOP DETECTOR

Low power loop detectors.

Model LD7LP

ACCESSORIES

POST-MOUNTING PLATE

For post-mounting commercial slide/swing operators. Posts not included.

Model MPEL

PLUG-IN LOOP DETECTOR

Conveniently plugs into existing control board.

Model LOOPDETLM

6

SOLAR PANEL KIT - 10 WATT

This kit is to replace or add a solar panel to the operator application. Up to three

solar panels can be connected to the operator.

Model SOLPNL10W12V (requires 2 minimum)

SOLENOID GATE LOCK

The automatic gate lock is a solenoid-driven lock that automatically unlocks when

the gate is open and locks when the gate is closed. Can be mounted onto a gate or

post. Can be released in case of emergency.

Models GC824 (115 Vac) and CC824-12 (12/24 Vac/dc)

BATTERY FOR GATE ACCESS SYSTEMS

Gate access system batteries replace or upgrade the gate operator batteries.

Model 29-NP712 (standard 7 AMP-Hour Battery, 12 Vdc, to replace original

batteries provided with operator, reuse existing harnesses)

Model A12330SGLPK (upgrade 33 AMP-Hour Battery, 12 Vdc, includes 33AH

harness. Ideal for solar applications and extended battery backup)

Two identical 12 Vdc batteries are required for each gate operator. Do not mix 7AH

and 33AH batteries within a gate operator.

Model K75-34986-2 (battery tray for slide operator)

Model 10-36183 (battery tray for swing operator)

MAGNETIC GATE LOCK

Outdoor magnetic lock, transformer, junction box, mounting plate and hardware.

Not for use with Solar Applications. Must be powered separately.

Model MG1300

ACCESSORIES

VEHICLE SENSING PROBE

The vehicle sensing probe is buried in the ground and can detect a car as it

approaches and will then open the gate.

Model CP3

845 Larch Avenue

Elmhurst, Illinois 60126-1196

01-35591 © 2011, The Chamberlain Group, Inc. – All Rights Reserved