Liftmaster Mt Owners Manual 01 34215
Liftmaster-Mhs-Owners-Manual liftmaster-mhs-owners-manual
Liftmaster-Mgj-Owners-Manual liftmaster-mgj-owners-manual
Liftmaster-Mj-Owners-Manual liftmaster-mj-owners-manual
2014-07-19
: Liftmaster Liftmaster-Mt-Owners-Manual liftmaster-mt-owners-manual liftmaster pdf
Open the PDF directly: View PDF 
.
Page Count: 12
| Download | |
| Open PDF In Browser | View PDF |
MEDIUM DUTY LOGIC USER’S GUIDE MH 5011E MHS 5011E MT 5011E BMT 5011E MGJ 5011E MJ 5011E Contact Information Radio Receiver Built on Board Installation Date www.liftmaster.com 315MHz INTRODUCTION Congratulations on purchasing a quality, LiftMaster Medium Duty Commercial Door Operator. Your new operator is capable of operating up to 12 cycles per hour or 50 cycles per day. It is equipped with a built in radio receiver that is compatible with our existing 315 MHz product line as well as a Timer To Close (TTC) feature that can be enabled when LiftMaster Commercial Protector System® is installed and aligned properly. BASIC PROGRAMMING DETERMINE THE WIRING TYPE CAUTION The functionality of this operator is based on the wiring type. The operator is shipped from the factory in standard C2 wiring type (factory default). Some wiring types will require an optional safety device. Refer to the following descriptions of wiring types, requirements and programming. To prevent possible SEVERE INJURY or DEATH, install reversing sensors when: • The radio is used. • The 3-button control station is out of sight of the door. • Or ANY other control (automatic or manual) is used. Reversing devices are recommended for ALL installations. NOTE: 1. The LED on the logic board will blink once when in C2 and twice when in B2. 2. The operator will automatically convert to B2 wiring (option D) when Monitored Safety Device is installed. If the Monitored Safety Device is removed, the operator will go into a Restricted Close mode**. Turn power OFF and ON to reset wiring type. ** Restricted close mode requires a constant pressure close command. The operator will begin closing after a 5 second delay and will continue to close to the close limit switch. The operator will stop if the pressure to close is released before reaching the close limit. A WARNING AVERTISSEMENT C2 WIRING TYPE WITHOUT MONITORED SAFETY DEVICE (Factory Default) B • Momentary contact to open and stop with constant pressure to close. • Open override that reverses when closing by any opening device. • Wiring for safety device to reverse. NOTE: The operator will automatically convert to B2 wiring (option D) when Monitored Safety Device is installed. (See accessories page for Monitored Safety Devices) • Timer to Close (TTC) feature not available. NON-MONITORED SAFETY DEVICE ATTENTION C2 WIRING TYPE WITH MONITORED SAFETY DEVICE • Momentary contact to open and stop with constant pressure to close. • Open override that reverses when closing by any opening device. • Wiring for safety device to reverse. NOTE: The operator will automatically convert to B2 wiring (option D) when Monitored Safety Device is installed. (See accessories page for Monitored Safety Devices) • Timer to Close (TTC) feature not available. MONITORED SAFETY DEVICE ADVERTENCIA Sensing Edge Photo Eye PRECAUCIÓN RESET TO C2 WIRING TYPE (Factory Default) Remove any monitored safety devices. Disconnect then reconnect power to the operator. Press and hold the LEARN and STOP buttons until the LED goes out (approximately 3 seconds). Electrical Box TO PROGRAM Press and hold the LEARN and CLOSE buttons until the LED goes out (approximately 3 seconds). Logic Board Electrical Box LEARN STOP Logic Board CLOSE OPEN LEARN D14 LED D7 U4 D6 014A1030 C20 D4 D7 U4 D6 R25 014A1030 C20 TP1 L5 D5 D4 J4 C32 R25 C9 ^^^^ C31 U1 C21 CLOSE OPEN C32 C31 TP1 C9 AUX AUX ANT ANT STOP D14 LED D5 J4 U1 C21 C18 R27 J2 L5 LEARN STOP CLOSE OPEN LED D9 ^^^^ AUX AUX ANT ANT D14 TTC 1 2 3 4 5 6 7 LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN K2 LT C29 R24 P1 C18 1 2 3 4 5 6 R27 J2 7 D14 TTC LEARN STOP CLOSE OPEN LED D9 2 1 2 3 4 5 6 7 LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN K2 LT C29 R24 P1 1 2 3 4 5 6 7 BASIC PROGRAMMING B2 WIRING TYPE WITHOUT MONITORED SAFETY DEVICE C D Requires a non-monitored safety device. • Momentary contact to open, close and stop. • Open override that reverses when closing by any opening device. • Wiring for safety device to reverse. NOTE: The operator will automatically convert to B2 wiring (option D) when Monitored Safety Device is installed. (See accessories page for Monitored Safety Devices) • Timer to Close (TTC) feature not available. B2 WIRING TYPE WITH MONITORED SAFETY DEVICE • Momentary contact to open, close and stop. • Open override that reverses when closing by any opening device. • Wiring for safety device to reverse. NOTE: The operator will automatically convert to B2 wiring when Monitored Safety Device is installed. (See accessories page for Monitored Safety Devices) • Timer to Close (TTC) feature available. NON-MONITORED SAFETY DEVICE MONITORED SAFETY DEVICE Sensing Edge Photo Eye TO PROGRAM NO PROGRAMMING REQUIRED Start with operator in factory default C2 mode. Press and hold the LEARN and CLOSE buttons until the LED goes out (approximately 3 seconds). Electrical Box Logic Board D7 U4 D6 014A1030 C20 D5 D4 J4 C32 R25 C31 TP1 C9 U1 C21 LEARN L5 ^^^^ AUX AUX ANT ANT C18 R27 J2 STOP CLOSE OPEN D14 TTC LEARN STOP CLOSE OPEN LED D9 1 2 3 4 5 6 7 LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN K2 LT C29 R24 P1 D14 LED 1 2 3 4 5 6 7 3 BASIC PROGRAMMING REMOTE CONTROLS TIMER TO CLOSE (TTC) SINGLE BUTTON REMOTE CONTROL Built in 315 MHz radio receiver permits as many as 20 Security✚® remote controls or dip switch remote controls in any combination. Timer to Close feature enables the operator to close from the open limit after a preset time, adjustable from 5 to 60 seconds. Requires LiftMaster monitored safety device. TO PROGRAM 1. Press and release the LEARN button (LED will light). 2. Press and hold the button on the remote control until the LED flashes rapidly, then release to complete programming (LED will go out). 3. Repeat steps 1 and 2 for additional remote controls. TO PROGRAM 1. Begin with door in fully closed position. 2. Press and release the LEARN button (LED will light). 3. Press and release the TTC button. 4. Every press and release of the STOP button will add 5 seconds to the Timer to Close. Example: 30 second TTC = 6 presses of the STOP button. 5. Press and release the TTC button to exit programming mode. 6. The LED will flash once per 5 seconds of timer setting. The TTC will become active after completion of the next open cycle. Electrical Box Logic Board STOP LEARN CLOSE OPEN D14 LED D7 U4 D6 NOTE: The LED does not indicate that timer is running. D5 D4 J4 014A1030 C32 C20 R25 C31 TP1 C9 U1 C21 L5 ^^^^ AUX AUX ANT ANT C18 R27 J2 K2 LT LEARN STOP CLOSE OPEN C29 R24 P1 LED D9 1 2 3 4 5 6 7 LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN 2 1 D14 TTC 3 4 5 OPEN 6 7 TO VERIFY TIMER TO CLOSE (TTC) SETTING 1. Press and release the LEARN button. 2. Press and release the TTC button. 3. Press and release the TTC button a second time. 4. The LED will flash once per 5 seconds of timer setting. MEP1 LMEP2 COM INTRLK STOP CLOSE OPEN 3-BUTTON REMOTE CONTROL TO OPERATE AS A WIRELESS 3-BUTTON CONTROL STATION Logic Board Electrical Box Timer To Close Button NOTE: The feature will use 3 of the 20 memory channels in the operator. D7 U4 D6 014A1030 D7 U4 D6 014A1030 C20 D5 D4 J4 C32 C31 U1 1 ^^^^ C18 2 3 4 5 R27 D14 TTC LEARN STOP CLOSE OPEN LED D9 1 2 3 4 5 6 7 LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN K2 LT C29 R24 P1 LMEP1 LMEP2 COM INTRLK STOP CL CLEAR THE TIMER TO CLOSE (TTC) 1. Press and release the LEARN button (LED will light.) 2. Press and hold the TTC button for 6 seconds. 3. Release the TTC button (LED will go out). The TTC will no longer be active. TIMER DEFEAT The TTC can be temporarily disabled by pressing a STOP button. TTC will become enabled after the next open command. CLOSE OPEN D14 LED D5 D4 J4 C32 R25 C9 C31 TP1 CLO R25 C21 L5 J2 Logic Board STOP C20 TP1 C9 AUX AUX ANT ANT TO ERASE ALL REMOTE CONTROLS Press and hold the LEARN button (over 5 seconds) until the LED goes out. All programmed remote controls will be erased. LEARN STOP D14 LED TO PROGRAM Open 1. Press and hold the LEARN button Close Stop (LED will light). 2. Press the desired button on the logic board (OPEN, CLOSE or STOP). Release both buttons. 3. Press and hold the desired button of the remote control until LED flashes rapidly, then release. 4. Repeat steps 1 through 3 to program additional buttons. Electrical Box LEARN TTC U1 C21 L5 ^^^^ AUX AUX ANT ANT C18 R27 J2 D14 TTC LEARN STOP CLOSE OPEN LED D9 1 2 3 4 5 6 7 LMEP1 LMEP2 COM INTRLK STOP CLOSE OPEN K2 LT C29 R24 P1 1 2 3 4 5 6 7 RADIO OPERATION MODE OPEN CLOSE STOP B2 B2 with TTC C2 X X X (3 button remote) X X X X X X MEP1 LMEP2 COM INTRLK STOP CLOSE OPEN NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 4 X X REVERSE WHILE CLOSING TTC RESET X WHEN OPEN WARNING MANUAL DISCONNECT (MODELS MT/B MT & MH) The operators have provisions for manually operating the door in case of emergency or power failure. Refer to the appropriate instructions for your model operator. CAUTION To prevent possible SERIOUS INJURY or DEATH from a falling door or arm: • DO NOT stand under the door arm when pulling the emergency release. • If possible, use emergency release handle to disengage trolley ONLY when door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/ or unexpectedly. • NEVER use emergency release handle unless doorway is clear of persons and obstructions. MODEL MT/BMT Emergency Disconnect AVERTISSEMENT TO DISCONNECT DOOR FROM OPENER Emergency Disconnect Door Arm NOTI C E Door TO RECONNECT DOOR ARM TO TROLLEY ATTENTION Pull emergency release handle straight down. Emergency disconnect will open. Emergency Disconnect Door Arm Emergency Release Handle Lift free end of door arm to trolley. Pull emergency handle to allow arm to engage roll pin. Release handle. Emergency disconnect will close. MODEL MH Chain Retaining Bracket (with pad locking provisions) These operators are equipped with a manual hoist. An electrical interlock will disable the electrical controls when the hoist is used. To operate the hoist: ADVERTENCIA 1. Pull the disconnect chain (sash chain) to engage the hoist mechanism. The disconnect chain may be locked in position by slipping the end through the keyhole of the chain retaining bracket mounted on the wall. PRECAUCIÓN 2. Operate the door in the desired direction by pulling on one side or the other of the continuous loop hoist chain. 3. The disconnect chain must be released from the chain retaining bracket before the door will operate again electrically. Electrical Interlock with Hoist for Model MH 5 WARNING MANUAL DISCONNECT (MODELS MJ/MGJ & MHS) MODEL MJ/MGJ CAUTION This operator has a floor level disconnect chain to disconnect the door from the door operator. 1. To disengage, pull the chain and secure in the disengaged position by slipping the end through the keyhole bracket mounted on the wall. Or if emergency egress device is used, pull handle to disengage operator from door. 2. The door may now be pushed up or pulled down manually. 3. Release the disconnect chain or reset the emergency egress device to operate the door again electrically. To prevent possible SERIOUS INJURY from a moving chain, DISCONNECT electric power to the operator BEFORE manually operating your door. MODEL MHS This operator includes two methods of manual operation: 1. A disconnect sash chain for push-up/pull-down operation. This chain can be found on the hoist side of the operator. See Manual Disconnect - Model MJ/MGJ for instructions. 2. A hoist engagement sash chain for manual hoist operation. This chain can be found on the clutch side of the operator. See Manual Disconnect - Model MH for instructions. AVERTISSEMENT Keyhole Bracket When operator is disconnected by the manual operation chain, hoist and electrical operation will not function. ATTENTION Chain Retaining Bracket (with pad locking provisions) Hoist Chain Manual Disconnect for Models MJ and MGJ Electrical Interlock with Hoist Chain (when present) for Model MHS ADVERTENCIA PRECAUCIÓN 6 WARNING TESTING Turn on power, LED will flash 7 times on power up. Test all controls and safety devices to make sure they are working properly. If the operator does not function properly, contact your installing dealer. CAUTION WARNING WARNING To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric power BEFORE performing ANY maintenance. IMPORTANT NOTES: • Do not leave power to the operator on unless all safety and entrapment protection devices have been tested and are working properly. • Be sure you have read and understand all safety instructions included in this manual. • Be sure the owner or person(s) responsible for operation of the door have read and understand the safety instructions, know how to electrically operate the door in a safe manner and how to manually disconnect the door from the operator. TEST THE SAFETY DEVICES (IF INSTALLED) 1. Open the door. 2. Place an obstruction in the path of the photo eyes or sensing edge. 3. Press the CLOSE button. The door should not close if photo eyes are installed. The door should close to obstruction and reverse if sensing edge is installed. 4. Remove the obstruction. 5. Press CLOSE button. Door should close. If door did not reverse from obstruction, check safety devices. AVERTISSEMENT AVERTISSEMENT TEST 3-BUTTON CONTROL STATION 1. Press OPEN button. (The door should move in the open direction.) 2. Press STOP button. (The door should stop.) 3. Press CLOSE button. (The door should move in the close direction.) 4. Release CLOSE button. Door should stop if in C2 mode. (The door should continue closing if in B2 mode.) 5. Press STOP button. (The door should stop.) ATTENTION AVERTISSEMENT TEST REMOTE CONTROL * Requires B2 wiring type and compatible LiftMaster remote control. In C2 wiring the remote control will open the door only. 1. Press remote control button. 2. Door should open. Allow the door to fully open. 3. Press remote control button. 4. Door should close. Allow door to fully close. TEST LIMIT ADJUSTMENT 1. Press OPEN button. (The door should open.) 2. Allow the door to fully open. 3. Press CLOSE button. (The door should close.) 4. Allow the door to fully close. 5. If the limits are not set properly, contact your installing dealer. ADVERTENCIA ADVERTENCIA ADVERTENCIA PRECAUCIÓN 7 TROUBLESHOOTING To locate a dealer in your area visit us online at www.liftmaster.com CONDITION POSSIBLE CAUSE FIX OPERATOR WILL NOT RESPOND TO ANY COMMANDS No power ➤ Check circuit breaker. Accessory failure ➤ Verify photo eyes are aligned. Possible component failure ➤ Contact your installing dealer. OPERATOR MAKES NOISE BUT DOOR DOES NOT MOVE Operator requires adjustment ➤ Contact your installing dealer. DOOR DRIFTS AFTER OPERATOR STOPS Operator or door requires adjustment ➤ Contact your installing dealer. DOOR OPENS/CLOSES TOO FAR Operator requires adjustment ➤ Contact your installing dealer. DOOR REVERSES UNEXPECTEDLY Safety device activated ➤ Verify photo eyes are aligned. If photo eyes are aligned and operator still does not operate properly, contact your installing dealer. Remote control is not programmed ➤ See PROGRAMMING REMOTE CONTROLS section. Low battery ➤ Replace battery. REMOTE CANNOT BE PROGRAMMED Low battery ➤ Replace battery. POOR RANGE Low battery ➤ Replace battery. Possible radio interference ➤ Contact your installing dealer. RADIO FUNCTIONALITY NO RESPONSE MAINTENANCE SCHEDULE Every 3 months or 5,000 cycles repeat all tests in the Testing section. Call qualified service contractor for maintenance. To locate a dealer in your area visit us online at www.liftmaster.com. The operator should be serviced at the following intervals: • Every 3 months or 5,000 cycles • Every 6 months or 10,000 cycles • Every 12 months or 20,000 cycles WARNING To avoid SERIOUS PERSONAL INJURY or DEATH from electrocution, disconnect ALL electric power BEFORE performing ANY maintenance. CAUTION AVERTISSEMENT 8 ATTENTION O P E R AT O R N O T E S 9 O P E R AT O R N O T E S 10 O P E R AT O R N O T E S 11 OPEN ACCESSORIES OPEN ENTRAPMENT PROTECTION DEVICES REMOTE CONTROLS 315MHz 1-Button SECURITY✚® Remote Control: Includes visor clip. 371LM Monitored CPS-LN4 OPEN PRESS TO R ING Commercial Protector System®: Provides protection on doors up to 45' wide. NEMA-4 rated. OPEN 3-Button SECURITY✚® Remote Control: Includes visor clip. 373LM ® Commercial Protector System PRESS: TO RING Provides protection on doors up to 30' wide. CPS-L 333LM OPEN 3-Button Tri-Colored Dip Switch Remote Control: Includes visor clip. Wireless Single Push Button Control SECURITY✚®: Rugged composite housing. (Wireless controls can not be used in place of hardwired controls.) TO R ING Non-Monitored Vehicle Detection System Pneumatic Sensing Edge Kit ANTENNA EXT-ANT PRESS TO R ING WPB3LM WKP5LM 1 2 4 3 5 6 7 8 9 * 0 # Wireless 3 Button Control Station SECURITY✚®: Rugged composite housing. (Wireless controls can not be used in place of hardwired controls.) CLOSE PRESS 65-8202 WPB1LM OPEN 86LM (15') 86LMT (25') Wireless Access Control Keypad SECURITY✚®: Rugged composite housing. (Wireless controls can not be used in place of hardwired controls.) External Antenna: The external antenna can be used to increase the radio receiver range. Antenna Extension Kit: The antenna extension kit can be used with EXT-ANT for maximum radio receiver range. CONTROL STATIONS 2-Button Control Station: Steel enclosure. 02-102 WIRE 65-7WIREL 7 Conductor 20 AWG Wire (500'): Recommended for control wiring. 21-2LM 2-Strand 22 AWG Wire (500'): Color coded, white and white/black. OPEN CLOSE 3-Button Control Station: Steel enclosure. 02-103 PRESS ^ OP EN OPEN TO R ING OPEN ^ CLOS E CLOSE O STOP CLOSE Key Control Station: Indoor flush mount, NEMA 1. 02-109 OPEN CLOSE 50-104-1 Coil Cord 18 AWG Wire (20'): Black coil cord, 2 wire, 18 AWG, 20' extended. OPEN CLOSE 01-34215B © 2008, The Chamberlain Group, Inc. All Rights Reserved PRESS PRESS TO R ING
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Page Mode : UseOutlines XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:08:23 Modify Date : 2009:04:10 12:57:31-07:00 Create Date : 2008:08:04 07:42:55-07:00 Metadata Date : 2009:04:10 12:57:31-07:00 Format : application/pdf Title : 01-34215 Creator : The Chamberlain Group, Inc. Document ID : uuid:e7d18c79-043b-4b01-a01f-ff6348bdc5e7 Instance ID : uuid:534b1e9a-c0b5-c44f-a960-1b2622dff1b5 Page Count : 12 Author : The Chamberlain Group, Inc.EXIF Metadata provided by EXIF.tools