Lightolier Is 1055Lv Users Manual Lytecaster Downlights Instruction Sheets

: Lightolier Lightolier-Is-1055Lv-Users-Manual-572735 lightolier-is-1055lv-users-manual-572735 lightolier pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

/

INSTRUCTIONSHEETNO.
INSTALLATION

REFLECTOR

PROCEDURE

TRIM

LOW VOLTAGE

FOR

IN THE

1000LV

FRAME-IN

lS:1055LV

KIT

Page 1 of 2

0s90

READ AND

UNDERSTAND

THESE

lNSTRU~lONS

BEFORE

INSTALLING

FIXTURE.

This fixture is intended for installation
in accordance with the National Electrical Code and local regulation.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain

these

instructions

for maintenance

reference.

~~%~

FIG. A
1. FRAME-IN

FIG. D
4. PUSH-UP

FIG. C
3. SNAP~N

FIG. B
2. CLOSE-IN

WARNING: BEFORE INSTALLING REFLECTOR TRIM TO FRAME-IN KIT, REAO MARKINGS IN REFLECTOR TRIM
AND ‘IN BOCK~ CUP OF FRAME-IN-KIT TO DErERMINE LAMP WAlTAGE AND TYPE APPLICABLE FOR YOUR
lNBTA1.L&TiON. IF I.C. TYPE FRAMING KIT IS USED, IT MAY BE INSTALLED IN DIRECT CONTACT WITN INSULATED
CSIUNGS. IF A NON I.C. TYPE FRAME4N.KfT IS USED, DO NOT INSTALL INSULATION WITHIN 31NCHSB OF FI)MJRE
SIDE OR WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH A MANNER TO ENTRAP HSAT.
1.

FRAME-IN (Fig. A)
See Frame-In Kit Instruction
procedure.

r-

Sheet for installation

FRAMINGKIT

2.

ROTATE ROTO-CLIPS (Fig. B)
As shown in Fig. E.

3.

SNAP.ON (Fig. C).
Insert SOCKET through RECTANGLE HOLE on top
of REFLECTOR TRIM. Engage TAB from SOCKET
CUP into one of the SLOTS on top of REFLECTOR
TRIM and push other end of SOCKET CUP with
LANCING into the other SLOT (Fig. F),

4.

PUSH-UP (Fig. D).
Push REFLECTOR TRIM into ceiling
is flueh to ceiling (Fig. D).
N~E

Socket

manufacturers

MOUNTSFLUSH
ONCEILINGMATERIAL

,!;;

,..’
0“
\
.-.,,:.,-;’,.’.’.
, ; :.:.-.
....:.:.,
- ... \ ..,-....
.’$.’. .-

CEILING
MATERIAL

-,:.-...-:.

4

ROTO.CLIP ‘““::;~y
POSITION
:.,

;
,,

FIG. E
– SOCKETCUP

until flange
RECTANGLEHOLE

have suggested

that

~

SLOTa

socket may fail after 3 to 6 ralampings. If this
occurs, socket can be replaced by disconnecting

REFLECTOR
TRIM

male connectors
(attached to socket leads) from
female connectors
(attached to fixture leads) and
replacing it with a new socket procured through
Lightolier (Fig. G).
MALECONNECTORa
(ATTACHEDTO SOCKETWIRE)

INSULATINGSLEEVING

SEE BACK PAGE FOR LAMP INSTALLATION
AND ADJU~MENT.

FEMALECONNECTORS
(ATTACHEDTO FIXTUREWIRES)

MR16SOCKET

FIG. G

1-

I

<51“17<>

l-l

1=

,a@

:v:::::i,N:r::::,E:i:T:j

LAMPING

INSTRUCTIONS

AND ADJUSTMENTILOCKING

INSTALL LAMP
5.

Remove LAMP RING from LAMPIYOKE
pulling straight down (Fig. H).

6.

insert LAMP (MR-16) between LAMP SPRINGS until
face of LAMP sits firmly on GLASS LAMP GUARD
(Fig, l).

7.

Attach

s.

Insert LAMP RING with LAMP and GLASS LAMP
GUARD attached back into LAMP/YOKE HOLDER
(Fig. J).

SOCKET to hi-in prongs

HOLDER

IS1055LV
0890
Page 2 of 2

by

on LAMP (Fig. l).

/.fs~
==77=.

LAMP
SPRING

c

I-44:
GL4S&5L~MP

WARNING:

LAMP MANUFACTURERS
REQUIRE THE
GLASS IAMP GUARD BE IN PLACE BEFORE ENERGIZING
LAMP AND THAT GREAT CARE MUST BE TAKEN THAT
LAMP IS FULLY COOLED BEFORE RELAMPING. AVOID
FINGER MARKS WHEN HANDLING FOR THEY MAY CAUSE
~ SHORT LAMP LIFE AND POSSIBLE BREAKAGE.

FIG. H

VERTICAUANGLE ADJUSTMENT AND LOCK (Figd)
9.

LAMP

krserl a screwdriver into the LOCKING GUIDE on the
LAMP/YOKE HOLDER, and locate the clot in the
VERTICAL ADJUST/LOCK SCREW, turn the SCREW
counterclockwise,
and using the screwdriver as a
lever, tilt the entwe UMPIYOKE
HOLDER to the
desired angle. Once the desired angle ie reached,
tighten screw by turning screwdriver clockwise.

HORIZONTAL

GtiG~ARLMP

ADJUST AND LOCK (Fig. J)

10. The entire IAMPIYOKE

HOLDER can be horizontally
rotated to aim the an Ie of light as it leaves the hole
in the APERTURE TRI% (Fig. J). This can be done by
backing off the HORIZONTAL ADJUST/LOCK SCREW
one full turn, freeing the SUPPORT PLATE (Fig J).
Grasping the YOKES on either side of the
LAMP/YOKE HOLDER, rotate the SUPPORT PUTE
to the desired angle and lock the position by
tightening the HORIZONTAL ADJUST/LOCK SCREW.

FIG.

I

/

r

LAMP
ET

RELAMPING: The locking mechanisms designed within this
fixture allow ralamping without having to readjust and
relock. Follow Steps 5-8.

NOTE 1. LOW VOLTAGE FIXTURES should be
dimmed only with special dimmers Intended
apeclfloslly for that purpose Use Lightoiier
Lytemodej Soenlst, Cresoendo VA, Neptune VA,’
Preolelon VA, Essveet VA, Sunrise VA, Rediant VA or
equlvelant pfidu6te
by others or vsrisbie auto.
transformer’e or eieotmnlo dimmers intended for use
with low voltage flxturee. 2. Low voltsge fixtures msy
produoe audible eound when used with externel
dimmem which may be ob]ectional in acoustically
critical eree%

.

DE

FIG. J

WARNING:

USE ONLY REFLECTOR TRIMS PROVIDED By LIGHTOLIER INC. USE OF ~ER
MANUFA~RERS’
RSFLECTDR TRIMS VOIDS THE UNDER~rERS
LABORATORIES LISTING AND COULD CONSfTfUTE A FiRE HAZARD.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Modify Date                     : 2001:03:19 16:04:08-05:00
Create Date                     : 2001:03:19 15:59:16-05:00
Title                           : Lytecaster Downlights Instruction Sheets
Subject                         : Lightolier CD-ROM Specifier V3
Author                          : G.Tashian/Lightolier
Creator                         : Acrobat Capture 1.0
Producer                        : Acrobat PDFWriter 2.01 for Windows
Page Count                      : 2

EXIF Metadata provided by EXIF.tools