Lincoln Electric Imvertec Im738 A Users Manual
IM738-A to the manual f4c8e082-fad2-4d9a-b0a8-60cce6490350
2015-02-09
: Lincoln-Electric Lincoln-Electric-Imvertec-Im738-A-Users-Manual-574241 lincoln-electric-imvertec-im738-a-users-manual-574241 lincoln-electric pdf
Open the PDF directly: View PDF 
.
Page Count: 36
INVERTEC V160-T
O
#$&(#&S'R!")
!
November, 2010
'054CH4?4=3B>=->D
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However,
your overall safety can be
increased by proper installation
... and thoughtful operation on
your part. #"#("'(
#$&(#&&$&('
%)$!"(+(#)( &
"('!") "(
'(-$&)(#"' #"
("(&#)#)( And,
most importantly, think before
you act and be careful.
For use with machines having Code Numbers:
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
• World's Leader in Welding and Cutting Products •
Copyright © Lincoln Global Inc.
RETURN TO MAIN MENU
#&""
?>F4A434@D8?<4=C
1.a. Turn the engine off before troubleshooting and maintenance
work unless the maintenance work requires it to be running.
____________________________________________________
1.b. Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes
outdoors.
____________________________________________________
1.c. Do not add the fuel near an open flame
welding arc or when the engine is running.
Stop the engine and allow it to cool before
refueling to prevent spilled fuel from vaporiz-
ing on contact with hot engine parts and
igniting. Do not spill fuel when filling tank. If
fuel is spilled, wipe it up and do not start
engine until fumes have been eliminated.
____________________________________________________
1.d. Keep all equipment safety guards, covers and devices in
position and in good repair.Keep hands, hair, clothing and
tools away from V-belts, gears, fans and all other moving
parts when starting, operating or repairing equipment.
____________________________________________________
1.e. In some cases it may be necessary to remove safety
guards to perform required maintenance. Remove
guards only when necessary and replace them when the
maintenance requiring their removal is complete.
Always use the greatest care when working near moving
parts.
___________________________________________________
1.f. Do not put your hands near the engine fan.
Do not attempt to override the governor or
idler by pushing on the throttle control rods
while the engine is running.
___________________________________________________
1.g. To prevent accidentally starting gasoline engines while
turning the engine or welding generator during maintenance
work, disconnect the spark plug wires, distributor cap or
magneto wire as appropriate.
8
'(-
8
&+ "".&#)' $&#((-#)&' "#(&'&#!$#'' '&#)'")&-#&(
$ &"+-$!&+&&''#) #"') (+((&#(#&#&#$&("
Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you
purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box
351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available
from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
')& (( "'( (#" #$&(#"!"(""" &$&$&#)&'&
$&#&!#" --%) "*) '
+&""
(&"
!"( '
<0H1430=64A>DB
2.a. Electric current flowing through any conductor causes
localized Electric and Magnetic Fields (EMF). Welding
current creates EMF fields around welding cables and
welding machines
2.b. EMF fields may interfere with some pacemakers, and
welders having a pacemaker should consult their physician
before welding.
2.c. Exposure to EMF fields in welding may have other health
effects which are now not known.
2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:
2.d.1.
Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and
work cables. If the electrode cable is on your right
side, the work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close as
possible to the area being welded.
2.d.5. Do not work next to welding power source.
1.h. To avoid scalding, do not remove the
radiator pressure cap when the engine is
hot.
#&"$&#$#'(#"+&""'
Diesel engine exhaust and some of its constituents
are known to the State of California to cause can-
cer, birth defects, and other reproductive harm.
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
The Above For Diesel Engines The Above For Gasoline Engines
88
'(-
88
ARC RAYS can burn.
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
ELECTRIC SHOCK can
kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f.
Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
FUMES AND GASES
can be dangerous.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases. When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
fumes and gases away from the breathing zone. When
welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and within applicable OSHA PEL and
ACGIH TLV limits using local exhaust or mechanical ven-
tilation. In confined spaces or in some circumstances,
outdoors, a respirator may be required. Additional pre-
cautions are also required when welding on galvanized
steel.
5. b. The operation of welding fume control equipment is affected
by various factors including proper use and positioning of the
equipment, maintenance of the equipment and the specific
welding procedure and application involved. Worker expo-
sure level should be checked upon installation and periodi-
cally thereafter to be certain it is within applicable OSHA
PEL and ACGIH TLV limits.
5.c.
Do not weld in locations near chlorinated hydrocarbon
vapors
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors
to
form phosgene, a highly toxic gas, and other irritating prod-
ucts.
5.d. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.
5.e. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.
5.f. Also see item 1.b.
888
'(-
888
FOR ELECTRICALLY
powered equipment.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
CYLINDER may explode
if damaged.
7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
process used and properly operating
regulators designed for the gas and
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.
7.c. Cylinders should be located:
• Away from areas where they may be struck or subjected to
physical damage.
• A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
WELDING and CUTTING
SPARKS can
cause fire or explosion.
6.a.
Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
the welding sparks from starting a fire.
Remember that welding sparks and hot
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact can
cause overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even
though
they have
been “cleaned”. For information, purchase “Recommended
Safe Practices for the
Preparation
for Welding and Cutting of
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f.
Sparks and spatter are thrown from the welding arc. Wear oil
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate circuits.
This can create fire hazards or overheat lifting chains or
cables until they fail.
6.h. Also see item 1.c.
6.I. Read and follow NFPA 51B “ Standard for Fire Prevention
During Welding, Cutting and Other Hot Work”, available from
NFPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma
022690-9101.
6.j. Do not use a welding power source for pipe thawing.
Refer to http://www.lincolnelectric.com/safety for additional safety information.
8E
'(-
8E
$&J)(#"''Q&(J
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv-
antes:
'LA4CK$>DA'>D3064 SA2
1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble
de soudage et la machine à souder en bon et sûr état
defonctionnement.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.
3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi qu’un verre blanc afin de se protéger les yeux du ray-
onnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
b. Porter des vêtements convenables afin de protéger la
peau de soudeur et des aides contre le rayonnement de
l‘arc.
c. Protéger l’autre personnel travaillant à proximité au
soudage à l’aide d’écrans appropriés et non-inflammables.
4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan-
talons sans revers, et chaussures montantes.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.
8. S’assurer que la masse est connectée le plus prés possible
de la zone de travail qu’il est pratique de le faire. Si on place
la masse sur la charpente de la construction ou d’autres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de lev-
age, câbles de grue, ou autres circuits. Cela peut provoquer
des risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté, voir
le code “Code for safety in welding and cutting” CSA Standard
W 117.2-1974.
$&J)(#"''Q&(J$#)&
'!"'P'#)&P
(&"'#&!()&(P
&&'')&
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
3. Avant de faires des travaux à l’interieur de poste, la debranch-
er à l’interrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur
place.
EE
Thank You for selecting a %) (- product. We want you to take pride in
operating this product ••• as much pride as we have in bringing
this product to you!
&403C78B#?4A0C>AB!0=D0;2><?;4C4;H before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:
+&""
This statement appears where the information <DBC be followed 4G02C;H to avoid B4A8>DB?4AB>=0;8=9DAH or ;>BB>5;854.
This statement appears where the information <DBC be followed to avoid <8=>A?4AB>=0;8=9DAH or 30<064C>C78B4@D8?<4=C.
)(#"
$;40B4 G0<8=4 0AC>= 0=3 @D8?<4=C >A 0<064 <<4380C4;H
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.
Please record your equipment identification information below for future reference. This information can be
found on your machine nameplate.
Product _________________________________________________________________________________
Model Number ___________________________________________________________________________
Code Number or Date Code_________________________________________________________________
Serial Number____________________________________________________________________________
Date Purchased___________________________________________________________________________
Where Purchased_________________________________________________________________________
Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.
#= 8=4 $A>3D2C &468BCA0C8>=
- Register your machine with Lincoln Electric either via fax or over the Internet.
• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.
• For On-Line Registration: Go to our
+R'(0CFFF;8=2>;=4;42CA822><Choose “Quick Links” and then
“Product Registration”. Please complete the form and submit your registration.
)'(#!&'''("$# -
The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip-
ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln
Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses-
sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor-
mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer’s particular purpose,
with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or
correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any
warranty with respect to the sale of our products.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control
of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in
applying these types of fabrication methods and service requirements.
Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com
for any updated information.
E8
E8 ( ##"("('
Page
=BC0;;0C8>='42C8>=
Technical Specifications .......................................................................................................A-1
Select Suitable Location.......................................................................................................A-2
Stacking................................................................................................................................A-2
Tilting ....................................................................................................................................A-2
Machine Grounding and High Frequency Interference Protection .......................................A-2
Input Connections ................................................................................................................A-3
Ground Connection........................................................................................................A-3,A-4
ARFU (Auto-Restore Fuse)....................................................................................A-4
Output Connections..............................................................................................................A-5
Output and Gas Connection for Tig Welding........................................................................A-5
Output Connection for Stick Welding....................................................................................A-5
Work Cable Connection........................................................................................................A-5
Quick Disconnect Plug ..................................................................................................A-6
Shielding Gas Connection.............................................................................................A-6
Remote Control Connection..........................................................................................A-6
________________________________________________________________________________
#?4A0C8>='42C8>=
Safety Instructions................................................................................................................B-1
General Description..............................................................................................................B-1
Welding Capability................................................................................................................B-1
Limitations ............................................................................................................................B-1
Rear Conrol Panel................................................................................................................B-2
Controls and Settings, 2 Step and 4 Step Tig Sequence .......................................B-2 thru B-5
DIP Switch Functions (Service Information) .........................................................B-6 thru B-11
DIP Switch 1: Machine Type ........................................................................................B-6
DIP Switch 2: Preflow Timer.........................................................................................B-6
DIP Switch 3: 2 Step Restart Enable............................................................................B-7
DIP Switch 4: 4 Step Restart Enable....................................................................B-8, B-9
DIP Switch 5: Low OCV Enable .................................................................................B-10
DIP Switch 6: European/USA Machine Configuration................................................B-10
DIP Switch 7 & 8: Upslope Timer ...............................................................................B-11
Start/Crater Current Adjustment ..................................................................................B-11
________________________________________________________________________________
224BB>A84B'42C8>=
Optional Accessories and Compatible Equipment.................................................C-1
Factory, Field Installed...........................................................................................C-1
________________________________________________________________________
!08=C4=0=24 '42C8>=
Safety Precautions ................................................................................................D-1
Input Filter Capacitor Discharge Procedure ..........................................................D-1
Routine Maintenance.............................................................................................D-1
________________________________________________________________________
(A>D1;4B7>>C8=6 '42C8>=
How to Use Troubleshooting Guide .......................................................................E-1
Troubleshooting Guide.............................................................................E-2 thru E-4
________________________________________________________________________
+8A8=6806A0< '42C8>=
////////////////////////////////////////////////////////////////////////
$0ACB 8BCB$
////////////////////////////////////////////////////////////////////////
"'( (#"
*(
=?DC8A2D8C
115V (20A Plug and Branch)
115V (30A Branch)
230V (30A Branch)
230V (30A Branch)
!0G8<D<#?4=8A2D8C*>;C064
48 Volts Max.
DCHH2;4
100%
35%
100%
#DC?DCDAA4=C&0=64
5-160 Amps
"$)('" $'#" -
&(#)($)(
#)($)(
4867C +83C7 4?C7 +4867C
12.6 in. 7.9 in. 16.9 in. Approx. 24.2lbs.
320 mm 200 mm 430 mm 11 kgs.
$-' !"'#"'
(!$&()&&"'
#$&("(!$&()&&"
-20°C to +40°C
'(#&(!$&()&&"
-50°C to +85°C
&#!!""$)(+&")''.'#&!,!)!&(#)($)(
"$)(*# (
&%)"-.
230/50/60
!,!)!(! -&)(
&&#&)''.!$'
30
(-$''#'('(##&,(&
&)'"$)(#&+
#12
(" '$(#"'*(
=?DC*>;C064BI
115 V (20 A Plug and branch)
115 V (30 A branch)
230 V
!0G=?DCDAA4=C0CA0C43#DC?DC
20 A
25 A
34 A
#DC?DC<?B
60 (Stick)
90 (TIG)
80 (Stick)
110 (TIG)
160 (Stick)
160 (TIG)
130 (Stick)
130 (TIG)
#DC?DC*>;CB
22.4
13.6
23.2
14.4
26.4
16.4
25.2
15.2
(H?4>5#DC?DC
DC
"'( (#"
*(
&4034=C8A48=BC0;;0C8>=B42C8>=145>A4BC0AC8=6
8=BC0;;0C8>=
'(-$&)(#"'
(&'#20=:8;;
•#=;H@D0;85843?4AB>==4;B7>D;3?4A
5>A<C78B8=BC0;;0C8>=
M 8B2>==42C8=?DC?>F4A1HA4<>E8=6
?;D65A><A424?C02;4145>A4 F>A:8=6
8=B834*(;;>F<0278=4C>B8C5>A
<8=DC4B
<8=8<D<C>0;;>FC74?>F4A20?028C>AB
C>38B270A64145>A4F>A:8=68=B834C78B4@D8?
<4=C
• Insulate yourself from the work and ground.
• Always wear dry insulating gloves.
•
;F0HB2>==42CC74*(C>0?>F4ABD??;H
6A>D=343022>A38=6C>C74"0C8>=0;;42CA820;>34
0=3;>20;2>34B
------------------------------------------------------------
' (')( #(#"
This machine will operate in harsh environments.
However, it is important that simple preventative
measures are followed to assure long life and reliable
operation.
• Do not place or operate this machine on a surface
with an incline greater than 15° from horizontal.
• This machine must be located where there is free
circulation of clean air without restrictions for air
movement to and from the air vents. Do not cover
the machine with paper, cloth or rags when switched
on.
• Dirt and dust that can be drawn into the machine
should be kept to a minimum.
• Keep the machine dry and do not place it on wet
ground or in puddles.
• Locate the machine away from radio controlled
machinery. Normal operation may adversely affect
the operation of nearby radio controlled machinery,
which may result in injury or equipment damage.
Read the section on “Machine Grounding and High
Frequency Interference Protection” in this manual.
• When operated in ambient temperatures greater
than 40°C, the output duty cycle may be reduced.
• Do not mount over combustible surfaces.
'("
The Invertec V160-T cannot be stacked.
( ("
Place the machine directly on a secure, level surface.
The machine may topple over if this procedure is not
followed.
!"&#)"""&
%)"-"(&&"$&#((#"
The Capacitor Discharge Circuit used in the high fre-
quency generator can be blamed for many radio, TV
and electronic equipment interference problems.
These problems may be the result of radiated interfer-
ence. Proper grounding methods can reduce or elimi-
nate radiated interference.
The Invertec V160-T has been field tested under rec-
ommended installation conditions. It complies with
FCC allowable limits for radiation.
Radiated interference can develop in the following
four ways:
1. Direct interference radiated from the welder.
2. Direct interference radiated from the welding leads.
3. Direct interference radiated from feedback into the
power lines.
4. Interference from re-radiation of “pickup” by
ungrounded metallic objects.
+&""
"'( (#"
*(
Keeping these contributing factors in mind, installing
equipment per the following instructions should mini-
mize problems.
1. Keep the welder power supply lines as short as
possible and enclose as much of them as possible
in rigid metallic conduit or equivalent shielding for a
distance of 50ft. (15.2m). Both ends of the conduit
should be connected to a driven ground and the
entire length should be continuous.
2. Keep the work and electrode leads as short as pos-
sible and as close together as possible. Lengths
should not exceed 25ft. (7.6m). Tape the leads
together when practical.
3. Be sure the torch and work cable rubber coverings
are free of cuts and cracks that allow high frequen-
cy leakage. Cables with high natural rubber con-
tent, such as Lincoln Stable-Arc®better resist high
frequency leakage than neoprene and other syn-
thetic rubber insulated cables.
4. Keep the torch in good repair and all connections
tight to reduce high frequency leakage.
5. The work terminal must be connected to a ground
within ten feet of the welder, using one of the follow-
ing methods.
a) A metal underground water pipe in direct con-
tact with the earth for ten feet or more.
b) A 3/4” (19mm) galvanized pipe or a 5/8”
(16mm) solid galvanized iron, steel or copper
rod driven at least eight feet into the ground.
The ground should be securely made and the
grounding cable should be as short as possible
using cable of the same size as the work cable, or
larger. Grounding to the building frame electrical
conduit or a long pipe system can result in re-radi-
ation, effectively making these members radiating
antennas.
6. Keep all panels securely in place.
7. All electrical conductors within 50 ft (15.2m) of the
welder should be enclosed in grounded, rigid metal-
lic conduit or equivalent shielding. Flexible metallic
conduit is generally not suitable.
8. When the welder is enclosed in a metal building,
several earth driven electrical grounds connected
(as in 5 (b) above) around the periphery of the
building are recommended.
Failure to observe these recommended installation
procedures can cause radio or TV interference prob-
lems.
"$)(#""(#"'
(&'#20=:8;;
M0E40 @D0;858434;42CA8280=8=BC0;;
0=3B4AE824C78B4@D8?<4=C
M 8B2>==42C8=?DC?>F4A1HA4<>E8=6
?;D65A><A424?C02;4145>A4F>A:8=6
8=B834*(;;>F<0278=4C>B8C5>A
<8=DC4B
<8=8<D<C>0;;>FC74?>F4A20?028C>AB
C>38B270A64145>A4F>A:8=68=B834C78B4@D8?
<4=C
M>=>CC>D274;42CA820;;H7>C?0ACB
-----------------------------------------------------------------------
&#)"#""(#"
The frame of the welder must be
grounded. A ground terminal marked
with the symbol is located on the under
panel for this purpose. See your local
and national electrical codes for proper
grounding methods.
(746A>D=38=68BBD??;8438=C74 8=?DC 2>A3 8C 8B
8<?>AC0=CC70CC74'D??;H&424?C02;4A>D=32>=
=42C8>=8B2>==42C43
-----------------------------------------------------------------------
(78B8=BC0;;0C8>=B7>D;3 14 ?4A5>A<43 1H 0 @D0;8
58434;42CA8280= C> 4=BDA4 2>AA42C2>==42C8>=B>5
C74;403BC>C74?;D6B?034B
• (744;42CA820;BHBC4<<DBC 14<0341H B:8;;43
C427=8280=BF8C7 C74 B?428582?A>54BB8>=0;0=3
C427=820;@D0;85820C8>=B 0=3 8=2><?;80=24F8C7
C74A46D;0C8>=B8=5>A248=C742>D=CAHF74A4C74
4@D8?<4=C8B8=BC0;;43
• (74F4;38=6 ?>F4A B>DA24 BD??;H 201;4 8B ?A>
E8343F8C706A44=>AH4;;>F6A44=F8A4C70C<DBC
+-' 14 40AC743 (78B 6A44=>AH4;;>F6A44=
F8A4<DBC"*&14DB43F8C7>C74AE>;C064
2>=3D2C>AB
M;=BC0;;>=;H?;D6BC70C0A42>AA4B?>=38=6C>B054
CHA46D;0C8>=B
------------------------------------------------------------------------
+&""
)(#"
+&""
"'( (#"
*(
Fuse the input circuit with time delay fuses marked “D”
or delay type1circuit breakers. Using fuses or circuit
breakers smaller than recommended may result in
“nuisance” shut-offs from welder inrush currents even
if not welding at high currents.
1Also called inverse time or thermal/magnetic circuit
breakers. These circuit breakers have a delay in tripping
action that decreases as the magnitude of the current
increases.
The Invertec V160-T is recommended for use on an
individual branch circuit.
*"$)(
The rated output of the V160-T is available when con-
nected to a 30A branch circuit. When connected to a
branch circuit with lower ampacity, lower welding cur-
rent and duty cycle must be used. An output guide is
provided below. The values are approximate and must
be adjusted downward if the fuse or circuit breaker
trips off. Other loads on the circuit and fuse/circuit
breaker characteristics will affect the available output.
Do not exceed these welding conditions:
?;D6>=01A0=27
10% duty cycle
Stick: 65A
TIG: 95A
?;D6>=01A0=27
10% duty cycle
Stick: 75A
TIG: 105A
?;D6>=01A0=27
10% duty cycle
Stick: 85A
TIG: 120A
The Invertec V160-T is provided with a 115/230V
cable, 6.6ft.(2m) in length, with a 15Amp 5-15P plug
molded onto the cord.
The V160-T is supplied with an additional 20A plug
that can replace the 15A plug to achieve higher out-
put. To install the supplied 20A plug:
Connect the white (neutral) wire under terminal clamp
with silver screw, and black (hot) wire under terminal
clamp with brass screw. Connect green wire under
terminal clamp with green screw.
&))(#&'(#&)'
The dual input voltage machine is provided with an
ARFU device. It only operates when the input is con-
nected to an 115V supply and protects from input over
current conditions.
When the ARFU has been activated due to an input
over current condition, the output will be turned off and
the green Power LED will blink indicating an over-cur-
rent condition. This condition usually occurs when the
unit is operated beyond its rated duty cycle. The unit
will self-restore after a short time and will be ready for
normal operation once the green Power LED stops
blinking and remains on.
NOTE: The ARFU replaces a fuse (F2) that was used
in older V160’s.
•
08;DA4C>F8A40B8=BCAD2C43<0H20DB4?4AB>=0;
8=9DAH>A30<064C>4@D8?<4=C(>148=BC0;;43>A
2742:431H0=4;42CA8280=>A@D0;85843?4AB>=
>=;H
---------------------------------------------------------------------------
*"$)(
To achieve the full output capacity of the V160-T,
230VAC inputs should be used. The change over is
accomplished by replacing the 115VAC plug with a 30
Amp 230VAC plug (NEMA 6-30P).
((!"($ )
In all cases, the green or green/yellow grounding wire
must be connected to the grounding pin of the plug, usu-
ally identified by a green screw.
All attachment plugs must comply with the Standard for
Attachment Plugs and Receptacles, UL498.
The product is considered acceptable for use only when
an attachment plug as specified is properly attached to
the supply cord.
The Invertec V160-T will auto reconnect to either 115V
or 230V supplies.
""&*""&(#&
For use on engine drives, keep in mind the above
input draw restrictions and the following precaution.
The Invertec V160-T can be operated on engine driv-
en generators as long as the 230 volt auxiliary meets
the following conditions:
• The AC waveform peak voltage is below 400 volts*.
• The AC waveform frequency is between 45 and
65Hz.
• The RMS voltage of the AC waveform is always
greater than 208VAC *.
* for 115 VAC input divide these values in half.
+&""
"'( (#"
*(
OUTPUT CONNECTIONS
ELECTRIC SHOCK can kill.
• Keep the electrode holder, TIG
torch and cables insulation in good
condition and in place.
• Do not touch electrically live parts or electrode
with skin or wet clothing.
• Insulate yourself from work and ground.
• Turn the input line Switch on the Invertec V160-
T “off” before connecting or disconnecting out-
put cables or other equipment.
-------------------------------------------------------------
#)($)( #""(#" #& '(
+ ")&
First determine the proper electrode polarity for the
electrode to be used. Consult the electrode data for
this information. Then connect the output cables to the
output terminals corresponding to this polarity. For
instance, for DC(+) welding, connect the electrode
cable (which is connected to the electrode holder) to
the “+” output terminal and the work cable (which is
connected to the work clamp) to the “-” output termi-
nal. Insert the connector with the key lining up with
the keyway, and rotate approximately 1/4 turn clock-
wise; until the connection is snug. Do not over tighten.
#)($)("'#""(#"#&
(+ ")&
This unit does not include a TIG torch, but one may be
purchased separately. The Lincoln PTA-9 (K1781-1 or
K1781-3 only with no gas valve) or PTA-17 (K1782-1
or K1782-3) are recommended for use with this
machine for this purpose; however, any similar TIG
torch can be used. To attach the Twist-Mate Plug to a
Lincoln Torch, slide the rubber boot onto the torch
cable (enlarge the boot opening if necessary), screw
the fitting on the torch cable into the brass connector
snugly and slide the boot back over the brass connec-
tor. (See Figure A.1a)
TIG ADAPTER
RETAINING COMPOUND
STRAIN RELIEF BOOT
TIG TORCH POWER CABLE WITH GAS FITTING
TIG ADAPTER
RETAINING COMPOUND
STRAIN RELIEF BOOT
TIG TORCH POWER CABLE WITH GAS FITTING
)&
WORK CLAMP
WORK CABLE
ELECTRODE
HOLDER
+&""
WORK CLAMP
WORK CABLE
TIG TORCH
)&
)&0
The ground lead and TIG Torch Twist Mate®
Connector are supplied with the welder. To connect
the cables, turn the Power Switch “OFF”. Connect the
torch Twist Mate plug into the DC(-) Electrode/Gas
Output Receptacle on the front of the welder and turn
it clockwise until tight.
+#& #""(#"
Next, connect the work cable to the “+” output terminal
in the same way.
To minimize high frequency interference, refer to
!0278=4 A>D=38=6 0=3 867 A4@D4=2H
=C4A54A4=24 $A>C42C8>=section of this manual for the
proper procedure on grounding the work clamp and
work piece.
The following Lincoln engine drives meet these condi-
tions when run in the high idle mode:
• Ranger 250,305
• Commander 300, 400, & 500
Many engine drives do not meet these conditions (eg
Miller Bobcats, etc). Operation of the Invertec V160-T
is not recommended on engine drives not conforming
to these conditions. Such combinations may overvolt-
age the Invertec V160-T power source.
"'( (#"
*(
&!#(#"(&# #""(#"
A remote control receptacle is provided on the lower
center case front of the welder for connecting a
remote control to the machine. Refer to the Optional
Accessories section of this manual for available
remote controls.
The following items can be connected to the 6 pin
socket on the front panel:
• Remote control potentiometer (K857) for Stick
welding.
•
Remote Foot Amptrol (K870), Hand Amptrol (K963-3).
• Arc Start Switch (K814).
- "&2>D;34G?;>34
8530<0643
M44? 2H;8=34A D?A867C 0=3
2708=43C>0BD??>AC
M44?2H;8=34A0F0H5A><0A40BF74A48C
2>D;31430<0643
M"4E4A0;;>FC74C>A27C>C>D27C742H;8=34A
M44?2H;8=34A0F0H 5A><;8E44;42CA820;28A
2D8CB
///////////////////////////////////////////
+&""
%)'#""($ )#&'(
(&#
A quick disconnect system is used for the welding
cable connections. The stick electrode cable will need
to have a plug attached.
1. Cut off welding cable lug, if present.
2. Remove .75 in. (19mm) of welding cable insulation.
3. Slide rubber boot onto cable end. The boot end
may be trimmed to match the cable diameter. Use
soap or other nonpetroleum-based lubricant to
help slide the boot over the cable, if needed.
4. Cut 45-50% of the copper strands back 1/4” (6
mm).
5. Fold copper strands over cut strands and insert
into ferrule.
6. Slide the copper ferrule into the brass plug.
7. Tighten set screw to collapse copper tube. Screw
must apply pressure against welding cable. The
top of the set screw will be well below the surface
of the brass plug after tightening.
8. Slide rubber boot over brass plug. The rubber boot
must be positioned to completely cover all electri-
cal surfaces after the plug is locked into the recep-
tacle.
19 mm
.75 in.
WELDING CABLE
BOOT
TRIM, IF REQ'D
TO FIT OVER CABLE
19 mm
.75 in.
WELDING CABLE
BOOT
TRIM, IF REQ'D
TO FIT OVER CABLE
6 mm
.25 in.
WELDING CABLE
6 mm
.25 in.
WELDING CABLE
12 mm max.
.50 in. max
WELDING CABLE
COPPER FERRULE
12 mm max.
.50 in. max
WELDING CABLE
COPPER FERRULE
SET SCREW
BRASS PLUG
COPPER TUBE
SET SCREW
BRASS PLUG
COPPER TUBE
' "'#""(#"
Obtain the necessary inert shielding gas. Connect the
cylinder of gas with a pressure regulator and flow
gage. Install a gas hose between the regulator and
gas inlet (located on the rear of the welder). The gas
inlet has a 5/16-18 right hand female thread; CGA
#032.
#$&(#"
*(
&4030=3D=34ABC0=3C78B4=C8A4B42C8>=145>A4
>?4A0C8=6H>DA<0278=4
'(-"'(&)(#"'
(&'#20=:8;;
• Do not touch electrically live parts such
as output terminals or internal wiring.
• Insulate yourself from the work and
ground.
• Always wear dry insulating gloves.
------------------------------------------------------------
-----------------------------------------------------------
------------------------------------------------------------
------------------------------------------------------------
Only qualified personnel should operate this equip-
ment. Observe all safety information throughout this
manual.
"& '&$(#"
The Invertec V160-T is an industrial 160 amp arc
welding power source which utilizes single phase
input power, to produce constant current output. The
welding response of this Invertec has been optimized
for stick (SMAW) and TIG (GTAW). The unit is ideal
for industrial applications where portability is impor-
tant.
The Invertec V160-T performs DC TIG with high fre-
quency or Touch Start Tig Starting with excellent
results.
+ "$ (-
The Invertec V160-T is rated at 160 amps, 26.4 volts,
at 35% duty cycle on a ten minute basis. It is capable
of higher duty cycles at lower output currents. It is
capable of 130 amps, 25.2 volts at 100% duty cycle(1).
If the duty cycle is exceeded, a thermal protector will
shut off the output until the machine cools. See
Technical Specifications in A-1 for other rated outputs.
The Invertec V160-T is recommended for stick weld-
ing with such popular electrodes as Fleetweld®35,
Fleetweld 37, Fleetweld 180 and Jet-LH 78 MR.
!((#"'
The V160-T is not recommended for pipe thawing.
(1)When connected to 230VAC inputs.
+&""
)!'"''
20=1430=64A>DB
• Keep your head out of fumes.
• Use ventilation or exhaust to
remove fumes from breathing
zone.
&&-'
20=1DA=
• Wear eye, ear and body
protection.
+ ")(("0=3
#)"'$&'
20=20DB458A4>A4G?;>B8>=
• Keep flammable material away.
• Do not weld, cut or gouge on
containers that have held com-
bustibles.
#$&(#"
&&#"(&# $"
$>F4A'F8C27 Controls the input power to the
machine. Make sure the machine is properly con-
nected to the input supply before turning the
machine on.(See Figure B.1)
0= The cooling fan will turn ON when the
machine is turned ON and it will continue to run
whenever the output of the machine is ON. If the
output of the machine is OFF for more than five min-
utes, the fan will turn OFF. This reduces the amount
of dirt that is deposited inside the machine and
reduces power consumption.(See Figure B.1)
Refer to the Output LED section below for more
information about conditions when the output of the
machine is ON.
0B=;4C Connector for the TIG shielding gas. The
gas source must have a pressure regulator and
flow gage installed.(See Figure B.1)
#"(&# '"'(("'(See Figure B.2)
!>34'F8C27 This switch changes the welding
modes of the machine. The V160-T has three weld-
ing modes: 'C82: (SMAW), 85C( (GTAW) and
( (GTAW).
When the mode switch is in the Stick position, the fol-
lowing welding features are enabled:
• Hot Start: This is a temporary increase in the output
current during the start of the stick welding process.
This helps ignite the arc quickly and reliably.
• Arc Force: This is a temporary increase in the out-
put current during normal stick welding. This tem-
porary increase in output current is used to clear
intermittent connections between the electrode and
the weld puddle that occur during normal stick
welding.
• Anti-Sticking: This is a function which decreases
the output current of the machine to a low level
when the operator makes an error and sticks the
electrode to the work piece. This decrease in cur-
rent allows the operator to remove the electrode
from the electrode holder without creating large
sparks which can damage the electrode holder.
*(
1
2
3
1
2
3
)&
$>F4A'F8C27
0=
0B=;4C
#$&(#"
When the mode switch is in the 85C ( position, the
stick welding functions are disabled and the machine is
ready for 85C( welding. 85C( is a method of start-
ing a TIG weld by first pressing the TIG torch electrode
on the work piece in order to create a low current short
circuit. Then, the electrode is lifted from the work piece to
start the TIG arc. After machine output is triggered ON,
with an Arc Start Switch or Foot Amptrol the arc must be
started within 6.5 seconds or output will turn OFF and
trigger sequence must be restarted.
When the mode switch is in the ( position, the stick
welding functions are disabled and the machine is ready
for ( welding. During the ( mode, the TIG
arc is started by HF without pressing the electrode on the
work piece. After triggering output ON, the HF (and out-
put) used for starting the TIG arc will remain ON for 6.5
seconds. If the arc is not started in this time limit, the trig-
ger sequence must be restarted.
(A8664A !>34 'F8C27 This switch changes between 2-
step and 4-step trigger sequences. For an explanation of
these trigger sequences refer to the Trigger Mode
Sequences following Controls and Settings.
$>F4A This indicator will blink on and off when
the machine is first turned on. After approximately 2
seconds it will stop blinking and remain on to signal
that the machine is ready. The indicator will also blink
during over current conditions when operating on
115V input.
(74A<0; This indicator will turn on when the
machine is overheated and the output has been disabled.
This normally occurs when the duty cycle of the machine
has been exceeded.
*(
!>34'F8C27
(A8664A!>34'F8C27
$>F4A
(74A<0;
&4<>C4
#DC?DC
#DC?DCDAA4=C>=CA>;
>F=B;>?4>=CA>;
$>BC5;>F>=CA>;
868C0;8B?;0H
Leave the machine on to allow the internal components to
cool. When the indicator turns off, normal operation is
again possible.
&4<>C4 This indicator will turn ON when a
remote control is connected to the machine via the
remote control connector. Using a remote control will
change the function of the output current control., refer
to the output current control section below. (Note:
When K814 Arc Start Switch is connected to remote
connector, remote LED will remain OFF).
#DC?DC This indicator turns on when the output
of the machine is on.
• In the stick welding mode, the output of the machine
is automatically turned ON.
• For both of the TIG welding modes, the output of the
machine is turned ON and OFF by an Arc Start
Switch or Hand/Foot Amptrol attached to the Remote
Control Connector. (See #4 - Mode Switch - above for
details on output triggering for TIG arc starting).
#DC?DCDAA4=C>=CA>; This controls the output or
welding current of the machine.
The function of this control knob is changed if a remote
control is connected. If the Remote LED is ON, this indi-
cates that a remote control is connected and the func-
tion of the output current control will be:
• Stick Welding Mode: The remote control will adjust
the output current of the machine from 5 to 160A.
The output current control knob on the display panel
is not used.
• TIG Welding Modes: The maximum output current of
the machine is set by the output current control knob.
The remote control then adjusts the output current
from the minimum output (5A) to the value set by the
output current control knob. For example, if the output
current control knob on the machine is set to 100A
then the remote control will adjust the output current
from a minimum of 5A to a maximum of 100A.
>F=B;>?4>=CA>; In the TIG welding modes, this
control knob will adjust the downslope time from 0.5
to 20 seconds. (The default upslope time is 0.5 sec-
onds.) Refer to the trigger sequence section below to
understand how downslope is activated. In Stick
welding mode, this function is not used.
)&
5
14
15
16
17
19
18
20
4
68
9
11
13
10
12
7
$D;B4!>34'F8C27
$D;B4
$D;B4A4@D4=24>=CA>;
02:6A>D=3DAA4=C>=CA>;
;42CA>34>==42C8>="460C8E4
&4<>C4>=CA>;>==42C>A
;42CA>34>==42C8>=$>BC8C8E4
#$&(#"
$>BC5;>F>=CA>; In the TIG welding modes, this
control knob will adjust the shielding gas postflow
time from 0.5 to 30 seconds. (The preflow time is
always 0.5 seconds.) In Stick welding mode, this
function is not used.
868C0;8B?;0H This meter displays the preset weld-
ing current before welding and the actual welding
current during welding. Like the output current con-
trol, the function of the meter is changed if a remote
control is connected.
$D;B8=6!>34 'F8C27 In the TIG welding modes,
this switch turns the pulsing function ON and controls
the pulsing frequency range (20Hz or 300Hz). In
Stick welding mode, this function is not used.
$D;B8=6 This indicator shows the pulsing fre-
quency when pulsing is turned ON. With this indica-
tion, the operator can adjust the frequency to the
desired value before welding. (Note: At higher fre-
quencies the LED blinks very fast and seems to be
continuously ON however it is pulsing.) If pulsing is
turned OFF or if the machine is in Stick welding
mode, the indicator will be OFF.
$D;B8=6A4@D4=2H>=CA>; When the pulsing func-
tion is ON, this control knob will adjust the pulsing
frequency. The pulsing frequency adjustment range is
0.2 - 20Hz or 3 - 300Hz depending on the Pulsing
Mode Switch position.
02:6A>D=3 DAA4=C>=CA>; When the pulsing
function is ON, this control knob will adjust the puls-
ing background current. This is the current during the
low portion of the pulse waveform; it can be adjusted
from 10% to 90% of the welding current.
(&&!#'%)"'
For the V160-T, TIG welding can be done in either the 2-
step or 4-step mode which is selected with the Trigger
Mode Switch. DIP Switch functions are set by the factory.
For adjustments on DIP Switch settings and functions
see DIP SWITCH FUNCTIONS in this Operations
Section.
'C4?'4@D4=24
Note: 2-Step works with either an Arc Start Switch (for
output triggering only, current control is at machine) or
with a Foot or Hand Amptrol™ (for both remote output
triggering and current control). 2-Step used with Arc Start
Switch is referenced in following sequence.
1. Press and hold the Arc Start Switch to start the
sequence.
The machine will open the gas valve to start the flow of
the shielding gas. After a 0.5 second preflow time to
purge air from the torch hose, the output of the
machine is turned ON. At this time the arc can be start-
ed.
After the arc is started the output current will be
increased to the welding current. The time for this
increase or upslope is presettable. The default is 0.5
seconds.
2. Release the Arc Start Switch to stop welding.
The machine will now decrease the output current at
a controlled rate or downslope time, until the
Start/Crater current is reached and the output of the
machine is turned OFF. The downslope time is
adjusted by the Downslope Parameter.
After the arc is turned OFF, the gas valve will remain
open to continue the flow of the shielding gas to the
hot electrode and work piece. The duration of this
postflow shielding gas is adjusted by the Postflow
Parameter. This operation is shown in (2 step dia-
gram 1).
Possible variations of this standard sequence is
shown below. It is possible to press and hold the TIG
torch trigger a second time during downslope to
restart. After the trigger is pressed the output current
will increase to the welding current. This operation is
shown in (2 step diagram 2).
*(
'C4?806A0<
'C4?806A0<
#$&(#"
*(
'C4?'4@D4=24
Note: 4-Step works with Arc Start Switch only. Amptrol™
type devices will not work properly and should not
be used. The Arc Start Switch's actuator is also
referred to as the "Tig torch trigger" in the following
sequence.
1. Press and hold the Arc Start Switch to start the
sequence. The machine will open the gas valve to
start the flow of the shielding gas. After 0.5 second
preflow time to purge air from the torch hose, the out-
put of the machine is turned ON. At this time the arc
can be started. After the arc is started the output cur-
rent will be at the Start/Finish current. This condition
can be maintained as long or as short as necessary.
If the Start/Finish current is not necessary, do not hold
the TIG torch trigger as described at the beginning of
this step. Instead, quickly press and release the trig-
ger. In this condition, the machine will automatically
pass from Step 1 to Step 2 when the arc is started.
2. Release the TIG torch trigger to start the main part of
the weld.
The output current will increase to the welding current.
The time for this increase or upslope is presettable.
The default is 0.5 seconds.
3. Press and hold the TIG torch trigger when the main
part of the weld is complete.
The machine will now decrease the output current at a
controlled rate or downslope time, until the Start/Finish
current is reached. The downslope time is adjusted by
the Downslope Parameter. This Start/Finish current
can be maintained as long or as short as necessary.
4. Release the TIG torch trigger.
The output current of the machine will turn OFF and
the gas valve will remain open to continue the flow of
the shielding gas. The duration of this postflow time is
adjusted by the Postflow control knob. This operation
is shown in (4 step diagram 1).
'C4?806A0<
Possible variations of this standard sequence are
shown below. It is possible to press and hold the TIG
torch trigger another time to end the downslope time
and maintain the output current at the Start/Finish cur-
rent. When the TIG torch trigger is released the output
will turn OFF and postflow will begin. This operation
shown in (4 step diagram 2).
'C4?806A0<
#$&(#"
$'+()"(#"'
The following sections explain the 8 DIP switch func-
tions of the V160. Read and understand the functions
before making any changes because abnormal opera-
tion can occur with the wrong settings. The machine
must be turned OFF when the DIP Switches are
changed.
(&'#"
4BDA4C70C0;;8=BC0;;0C8>=>?4A0
C8>=<08=C4=0=24 0=3A4?08A?A>24
3DA4B0A4?4A5>A<43>=;H1H@D0;85843
8=38E83D0;B 8=2>;=;42CA828B=>C
A4B?>=B81;45>A30<064B20DB431H8<?A>?4A
8=BC0;;0C8>=8<?A>?4A20A4>A01=>A<0;>?4A0C8>=
45>A4>?4=8=6C74 <0278=4 C> <0:4 270=64B C>
C74$'F8C274B8C<DBC 58ABC 14 CDA=43 #0=3
38B2>==42C435A><C748=?DCB>DA24>=>C>?4=
C74<0278=4>A270=64C74$'F8C274BF8C7
?>F4A0??;843C>C74<0278=4#=;H 8=2>;=
CA08=43B4AE824 C427=8280=B0A40DC7>A8I43C> ?4A
5>A<C74B4<>385820C8>=B
------------------------------------------------------------------------
The DIP switches are numbered from 1 to 8 shown in
Figure B.3. Switch 1 is on the bottom and switch 8 is
on the top. When a switch is pushed to the right (or to
the back of the machine) it is ON; when it is pushed to
the left (or to the front of the machine) it is OFF.
The standard production settings for the V160-T are
shown with in bold letters # Table B.1. If a switch
setting has bold letters #, do not make any
changes; abnormal operation could occur.
DIP Switch 1: Machine Type
This controls the output of the V160-T and some weld-
ing waveform functions. It configures the V160-T to
automatically turn OFF depending on the position of
the Welding Mode switch. Refer to DIP Switch 6 for
more information.
DIP Switch 2: Preflow Timer
This controls the preflow timer for TIG welding (used
only on "T" type machines). When the DIP switch is
OFF the preflow time is 0.5 seconds. When it is ON
the preflow time is 0.1 seconds.
)&
*(
+&""
DIP
Switch 1
DIP
Switch 8
Front of machine
DIP V160-T V160-T Pulse V160-T
Switch CE CE USA
1# # #
2 OFF OFF OFF
3 OFF OFF ON
4 ON ON OFF
5 OFF OFF OFF
6 OFF OFF ON
7 OFF OFF OFF
8 OFF OFF OFF
(
#$&(#"
$'F8C27'C4?&4BC0AC=01;4
This controls the 2 Step Restart function. When the
switch is ON the 2 Step Restart function is enabled.
2-Step Restart Disabled (DIP Switch 3 = OFF)
1. Press and hold the TIG torch trigger to start the
sequence. The machine will open the gas valve to
start the flow of the shielding gas. After the preflow
time, the output of the machine is turned ON. At
this time the arc is started according to the selected
welding mode (Lift TIG or HF TIG). After the arc is
started the output current will be increased (ups-
lope) to the welding current.
2. Release the TIG torch trigger to stop welding. The
machine will now decrease the output current at a
controlled rate (downslope), until the Start/Crater
current is reached and the output of the machine is
turned OFF. After the arc is turned OFF, the gas
valve will remain open for the duration of the post-
flow time. )&
As shown in figure B.5, it is also possible to press and
hold the TIG torch trigger a second time during
downslope to end the downslope time and maintain
the output current at the Start/Crater current. When
the TIG torch trigger is released the output will turn
OFF and the postflow time will start.
)&
'C4?&4BC0AC=01;43$'F8C27#"
Same as step 1.
Same as step 2.
As shown in figure B.6, it is possible to press and hold
the TIG torch trigger a second time during downslope
to restart. After the trigger is pressed the output cur-
rent will increase to the welding current, like in step 1.
When the main part of the weld is complete go to the
beginning of step 2. )&
*(
#$&(#"
$'F8C27'C4?&4BC0AC=01;4
This controls the 4 Step Restart function. When the
switch is ON the 4 Step Restart function is enabled.
("Foot pedal" remote controls should never be used
with the 4 step sequences.)
4-Step Restart Disabled (DIP Switch 4 = OFF)
1. Press and hold the TIG torch trigger to start the
sequence. The machine will open the gas valve to
start the flow of the shielding gas. After the preflow
time, the output of the machine is turned ON. At
this time the arc is started according to the selected
welding mode (Lift TIG or HF TIG). After the arc is
started the output current will be at the Start/Crater
current. This condition can be maintained as long
or as short as necessary.
)&
If the Start/Crater current is not necessary, do not hold
the TIG torch trigger as described at the beginning of
this step. Instead, quickly press and release it. In this
condition, the machine will automatically pass from
Step 1 to Step 2 when the arc is started.
2. Release the TIG torch trigger to start the main part
of the weld. The output current will be increased
(upslope) to the welding current.
3. Press and hold the TIG torch trigger when the main
part of the weld is complete. The machine will now
decrease the output current at a controlled rate
(downslope), until the Start/Crater current is
reached. This Start/Crater current can be main-
tained as long or as short as necessary.
3A. If it is not necessary to maintain the Start/Crater
current, the TIG torch trigger can be pressed and
released instead of holding it. In this case, step 4
will automatically follow.
4. Release the TIG torch trigger. The output current of
the machine will turn OFF and the gas valve will
remain open for the duration of the postflow time.
As shown in figure B.8, after the TIG torch trigger is
quickly pressed and released from step 3A, it is
possible to press and hold the TIG torch trigger
another time to end the downslope time and main-
tain the output current at the Start/Crater current.
When the TIG torch trigger is released the output
will turn OFF and postflow will begin.
)&
As shown in figure B.9, again after the TIG torch
trigger is quickly pressed and released from step
3A, it is possible to quickly press and release the
TIG torch trigger a second time to end the downs-
lope time and stop welding.
)&
*(
(1) (4)
(3)(2)
POST-FLOW POST-FLOW
––GAS ON––
(1) (4)
(3)(2)
POST-FLOW POST-FLOW
––GAS ON––
TORCH
BUTTON
OUTPUT
CURRENT
GAS
(3A) (4)
POST-FLOW
––GAS 0N––
TORCH
BUTTON
OUTPUT
CURRENT
GAS
(3A) (4)
POST-FLOW
––GAS 0N––
TORCH
BUTTON
OUTPUT
CURRENT
GAS
(3A)
POST-FLOW
––GAS ON––
TORCH
BUTTON
OUTPUT
CURRENT
GAS
(3A)
POST-FLOW
––GAS ON––
#$&(#"
'C4?&4BC0AC=01;43$'F8C27#"
Same as step 1.
Same as step 2.
3. Press and hold the TIG torch trigger when the main
part of the weld is complete. The machine will now
decrease the output current at a controlled rate
(downslope), until the Start/Crater current is
reached. This Start/Crater current can be main-
tained as long or as short as necessary.
)&
This sequence has an automatic restart so welding
will continue after this step. If the weld is completely
finished, use the following sequence instead of step
3 described above.
3A. Quickly press and release the TIG torch trigger.
The machine will now decrease the output cur-
rent at a controlled rate (downslope), until the
Start/Crater current is reached and the output of
the machine is turned OFF. After the arc is
turned OFF the postflow time will start.
4. Release the TIG torch trigger. The output current
will again increase (upslope) to the welding current,
like in step 2, to continue welding. When the main
part of the weld is complete go to step 3.
As shown in figure B.11, after the TIG torch trigger
is quickly pressed and released from step 3A, it is
possible to press and hold the TIG torch trigger
another time to end the downslope time and main-
tain the output current at the Start/Crater current.
When the TIG torch trigger is released the output
will again increase (upslope) to the welding current,
like in step 4, to continue welding. When the main
part of the weld is complete go to step 3.
)&
As shown in figure B.12, again after the TIG torch
trigger is quickly pressed and released from step
3A, it is possible to quickly press and release the
TIG torch trigger a second time to end the downs-
lope time and stop welding.
)&
*(
TORCH
BUTTON
OUTPUT
CURRENT
GAS ––GAS ON––
POST-FLOW
POST-FLOW
(1) (3A)
(4)
(3)
(2)
TORCH
BUTTON
OUTPUT
CURRENT
GAS ––GAS ON––
POST-FLOW
POST-FLOW
(1) (3A)
(4)
(3)
(2)
TORCH
BUTTON
OUTPUT
CURRENT
GAS
––GAS ON––
(3A) (4)
TORCH
BUTTON
OUTPUT
CURRENT
GAS
––GAS ON––
(3A) (4)
TORCH
BUTTON
OUTPUT
CURRENT
GAS
––GAS ON––
(3A)
POST-FLOW
TORCH
BUTTON
OUTPUT
CURRENT
GAS
––GAS ON––
(3A)
POST-FLOW
#$&(#"
$'F8C27 >F#*=01;4
This controls the OCV of the machine. When the
DIP switch is OFF the OCV is set to the normal level
as stated in the manuals for the machines. When
the DIP switch is ON the OCV is reduced to 20V.
This low OCV mode was created for the Australian
markets and should only be used as required by
these Australian specifications. The low OCV will
somewhat reduce the starting performance of the
machine when dirt, rust, and/or slag is present on the
work piece.
$'F8C27DA>?40=)'!0278=4
>=586DA0C8>=
This configures several functions of the V160 as
required by the European and USA markets. For the
European market it is OFF and for the USA market it
is ON.
Specifically, this configures the operation of the TIG
slope timers, remote control, and trigger. However,
this configuration also depends on the position of
DIP Switch 1 which selects the machine type. This
setting can be changed but only if the following func-
tions are clearly understood.
$'F8C27#
In TIG welding mode, the following conditions can
exist.
• European Machine Configuration (DIP Switch 6 =
OFF)
The TIG slope functions are always enabled. After
the arc is started the output current will be increased
(upslope) to the welding current. At the end of the
weld the current will be decreased with the downs-
lope function. Using a "foot pedal" remote control is
not recommended with this setup.
A trigger is always needed to turn ON the output of
the machine.
• USA Machine Configuration (DIP Switch 6 = ON)
The TIG slope functions depends on the possible
connection of a remote control.
• No remote control connected. The TIG slope func-
tions are enabled. After the arc is started the output
current will be increased (upslope) to the welding
current. At the end of the weld the current will be
decreased with the downslope function.
• Remote control connected. The TIG slope functions
are disabled for the 2 step trigger mode. If slopes
are needed a foot pedal remote control can be
used. The TIG slope functions are enabled for the 4
step trigger mode.
A trigger is always needed to turn ON the output of
the machine.
*(
#$&(#"
$'F8C27)?B;>?4(8<4A
These control the upslope timer for TIG welding
(used only on "T" type machines). The following
table shows the DIP Switch settings and selected
upslope time.
$'F8C27 $'F8C27 )?B;>?4(8<4
ON ON 0.1 seconds
OFF OFF 0.5 seconds
ON OFF 1 second
OFF ON 4 seconds
'C0ACA0C4ADAA4=C39DBC<4=C
The start/crater current of a "T" type machine can be
changed if necessary. The values are set from the fac-
tory.
European Machines:
20% (160A welding current = 32A start/crater current)
USA Machines:
10% (160A welding current = 16A start/crater current)
4BDA4C70C0;;8=BC0;;0C8>=>?4A0C8>=<08=C4
=0=240=3A4?08A?A>243DA4B0A4?4A5>A<43>=;H
1H@D0;858438=38E83D0;B 8=2>;= ;42CA828B=>C
A4B?>=B81;45>A30<064B20DB431H8<?A>?4A
8=BC0;;0C8>=8<?A>?4A20A4>A01=>A<0;>?4A0C8>=
(78B039DBC<4=C?A>243DA4<DBC14?4A5>A<43
>=;H1H 8=2>;=CA08=43 B4AE824 C427=8280=B (74
<0278=4F8;;14>?4A0C8=6F8C7C742>E4AA4<>E43
F74A48C8B?>BB81;4C>2><4 8=2>=C02CF8C77867
E>;C064B&4030;;C745>;;>F8=68=BCAD2C8>=B
145>A4BC0AC8=6C74?A>243DA4
(&'#"
M+4;38=64@D8?<4=C64=4A0C4B7867
E>;C064B
M>=>CC>D27C74;8E4?0ACB>5C74
<0278=4C744;42CA>34C74F>A:
2;0<?>A2>==42C43F>A:?8424B
F74=C78B4@D8?<4=C8B>=
M=BD;0C4H>DAB4;55A><;8E44;42CA820;2>==42
C8>=BC744;42CA>34C74F>A:2;0<?0=3C74
2>==42C43F>A:?8424B
-----------------------------------------------------------------------
1. Remove the cover of the machine to access the
control Printed Circuit Boards on the case front.
2. To adjust the start/crater current, output current
from the machine must flow through a load bank or
a TIG arc. Connect the necessary equipment. In
both cases, load bank or TIG arc, a trigger must be
connected to the machine. If a load bank is used, it
must be setup for 160A and approximately 25V.
3. Make sure all electrical connections are free from
contact with other parts of the machine. Reconnect
the case back if necessary. Turn ON the machine.
4. On the control panel of the machine, select the fol-
lowing:
• Mode Switch: LIFT TIG (Do not use HF TIG or
damage to measuring equipment will occur.)
• Trigger Mode: 4 Step
• Pulsing: OFF
• Output Current: Maximum (160A)
5. Activate the trigger of the machine to achieve the
start or crater current portion of the welding
sequence. Refer to the trigger sequences explained
above if more information is needed.
6. In this condition, measure the output current of the
machine and adjust the start/crater current as nec-
essary. The calibration trimmer for the start/crater
current is located on the left side of the machine (as
viewed from the front) on the display board. The
access hole for this trimmer is the higher one on the
display board. (Do not adjust the lower trimmer on
the display board; this is the output current calibra-
tion.)
The output current is set to 160A, therefore the
start/crater current calibration will be a percentage
of this 160A setting. Use the following equation for
determining the desired start/crater current calibra-
tion:
Desired start/crater current percentage multiplied
by 160 = calibration current.
For example, to calibrate the machine for 15%
start/crater current, multiply this by 160 to get the
calibration current ( 0.15 x 160 = 24).
7. Release the trigger to turn off the output of the
machine. Turn OFF the machine and disconnect it
from the input source. Reassemble the machine
making sure the ground wire to the cover is con-
nected.
*(
+&""
''#&'
#$(#" ''#&'
"#!$( %)$!"(
02C>AH=BC0;;43
1-Twist-Mate Torch Connector (W/Gas Pass Through)
1- Ground Lead and Plug Assembly
Strap Packet
Instruction Manual
84;3=BC0;;43
>>C<?CA>;C< for TIG welding. When the
V160-T’s Output Control is in the “REMOTE” position,
the foot Amptrol energizes the output and controls the
output remotely. The Foot Amptrol connects directly
to the 6 pin Amphenol.
0=3<?CA>;C< for TIG welding. When the
V160-T’s Output Control is in the “Remote” position,
the hand Amptrol energizes the output and controls
the output remotely. The Hand Amptrol connects
directly to the 6 pin Amphenol.
A2'C0AC 'F8C27 Energizes the output for
TIG welding if remote output control of the amperage
is not desired. It allows on/off TIG welding at the cur-
rent set by the Current Control on the control panel.
When using the Arc Start Switch set the Output
Control to the “LOCAL” position.
!06=D<N$(0=3$(((>A274B
The fol-
lowing standard Magnum® TIG torches with one-piece
cable may be used with the Invertec V160-T.
• K1781-1 PTA-9 12.5 ft medium back cap
• K1781-3 PTA-9 25 ft medium back cap
• K1782-1 PTA-17 12.5 ft long back cap
• K1782-3 PTA-17 25 ft long back cap
"#( Each torch requires a Twist-Mate
adapter,(one is included with the machine).
Collets, collet bodies, and nozzles are not
included and must be ordered separately.
$ )'
Cable Plug Kit for 1/0-2/0 cable. Attaches
to welding cable to provide quick disconnect from
machine.
(F8BC!0C4(>A2730?C4A One is shipped
with the welder to connect the Magnum PTA-9 torch. If
you do not care to interchange this part between
torches
(one is required to connect Magnum PTA-9 or
PTA-17 TIG torches with one-piece cable to the V160-T)
you may order an additional adapters. The quick con-
nect plug provides connection for both gas and weld-
ing current.
((>A27$0ACB8CBParts kits are available for the
PTA-9 and PTA-17 TIG torches. These kits include
back cap, collets, collet bodies, nozzles and tung-
stens.
#A34A$ for PTA-9 torches
#A34A$ for PTA-17 torches
See publication E12.150 for parts kits breakdown.
DC 4=6C7>=BD<01;4B TIG welding filler metals
are available for welding stainless steel, mild steel,
aluminum and copper alloys. See publication C9.10.
*(
!"(""
*(
'(-$&)(#"'
(&R'# can kill.
• Have an electrician install and serv-
ice this equipment.
• Turn the input power off at the fuse
box, disconnect supply lines and
allow machine to sit for five minutes
minimum to allow the power capaci-
tors to discharge before working
inside this equipment.
• Do not touch electrically live parts.
----------------------------------------------------------------------
"$)( (&$(#&
'&$&#)&
The machine has internal capacitors which are
charged to a high voltage during power-on conditions.
This voltage is dangerous and must be discharged
before the machine can be serviced. Discharging is
done automatically by the machine each time the
power is switched off. However, you must allow the
machine to sit for at least 5 minutes to allow time for
the process to take place.
------------------------------------------------------------------------
&#)("!"(""
Prevent metal powder from accumulating near the
Heat Sink fins.
•8B2>==42CC74?>F4ABD??;H145>A44E4AH>?4A0
C8>=.
------------------------------------------------------------------------
Carry out the following periodic controls on the power
source:
• Clean the power source inside by means of low-
pressure compressed air.
• Check the electric connections and all the connec-
tion cables.
M8B2>==42CC74?>F4ABD??;H145>A44E4AH>?4A
0C8>=
------------------------------------------------------------------------
• Always use gloves in compliance with the safety
standards.
WARNING
WARNING
WARNING
)(#"
(&#) '##("
*(
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
>20; 8=2>;=DC7>A8I4384;3'4AE824028;8CH for technical troubleshooting assistance before you proceed.
)(#"
This Troubleshooting Guide is provided to help you
locate and repair possible machine malfunctions.
Simply follow the three-step procedure listed below.
Step 1. LOCATE PROBLEM (SYMPTOM).
Look under the column labeled “PROBLEM (SYMP-
TOMS)”. This column describes possible symptoms
that the machine may exhibit. Find the listing that
best describes the symptom that the machine is
exhibiting.
Step 2. POSSIBLE CAUSE.
The second column labeled “POSSIBLE CAUSE” lists
the obvious external possibilities that may contribute
to the machine symptom.
Step 3. RECOMMENDED COURSE OF ACTION
This column provides a course of action for the
Possible Cause, generally it states to contact your
local Lincoln Authorized Field Service Facility.
If you do not understand or are unable to perform the
Recommended Course of Action safely, contact your
local Lincoln Authorized Field Service Facility.
#+(#)'(&#) '##(")
Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel.
Unauthorized repairs performed on this equipment may result in danger to the technician and
machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical
Shock, please observe all safety notes and precautions detailed throughout this manual.
__________________________________________________________________________
+&""
(&#) '##("
*(
#1B4AE40;;'054CHD834;8=4B34C08;43C7A>D67>DCC78B<0=D0;
$&# !'
'-!$(#!'
$#''
)'
&#!!"
#)&'#(#"
Excessive spatter
Craters
Inclusions
Insufficient penetration
Sticking
Porosity
Cracks
1. Long arc
2. High current
1. Fast movement of the electrode
away from piece.
1. Poor cleanliness or distribution of
the Welding passes.
2. Improper movement of the elec-
trode.
1. High progression speed.
2. Welding current too low.
3. Narrow chamfering.
1. Arc too short.
2. Current too low.
1. Humidity in electrode.
2. Long arc.
1. Current too high.
2. Dirty materials.
3. Hydrogen in weld (present on
electrode coating).
If all recommended possible areas of
misadjustment have been checked
and the problem persists, >=C02C
H>DA;>20; 8=2>;=DC7>A8I4384;3
'4AE824028;8CH
$&# !'"'(+ "
*(
(&#) '##("
#1B4AE40;;'054CHD834;8=4B34C08;43C7A>D67>DCC78B<0=D0;
$&# !'
'-!$(#!'
$#''
)'
&#!!"
#)&'#(#"
Oxidation
Tungsten inclusions
Porosity
Hot cracking
1. lnsufficient gas.
2. No protection on the back side.
1. lncorrect electrode sharpening.
2. Electrode too small.
3. Operating failure (contact of the
tip with the workpiece).
1. Dirt on the edges.
2. Dirt on the filler material.
3. Excessive travel speed.
4. Current intensity too low.
1 Unsuitable filler material.
2. High heat supply.
3. Dirty materials.
If all recommended possible areas of
misadjustment have been checked
and the problem persists, >=C02C
H>DA;>20; 8=2>;=DC7>A8I43
84;3'4AE824028;8CH
$&# !'"(+ "
(&#) '##("
*(
Observe all Safety Guidelines detailed throughout this manual
$&# !'
'-!$(#!'
$#''
)'
&#!!"
#)&'#(#"
Machine fails to come on
(Power LED off)
Power Input incorrect
Input over-current
(Power LED Flashing)
No output current
(Power LED on)
(Output LED off)
Thermal overload
(Thermal LED on)
1. No Input Voltage.
2. Faulty supply plug or cable.
3. Internal fuse blown.
1. Input voltage out of range (less
than 95 or greater than 265VAC).
2. Input current too high due to oper-
ating beyond rated duty cycle.
1. While in TIG mode, Trigger circuit
not mode at 6 pin amphenol.
1. Unit has been operated beyond its
capacity rating.
2. Airflow through machine is restrict-
ed or fan has failed.
If all recommended possible areas of
misadjustment have been checked
and the problem persists, >=C02C
H>DA;>20; 8=2>;=DC7>A8I43
84;3'4AE824028;8CH
(& )&'
F-1
DIAGRAMS
F-1
V160-T
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the
machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number.
WIRING DIAGRAM CODE 10878
F-2
DIAGRAMS
F-2
V160-T
V160-T WIRING DIAGRAM
1
2
4
3
AC1
AC2
GND
S1
BLUE
BROWN
WHITE
BLACK
YELLOW / GREEN
115/230/1/50/60
Vac
FAN
JP2
DC-A
DC+
Y/G
BLACK
RED DC+
DC-
GND
123 6541011987121513 14 16
135421067 98
JP1
JP1
1354 210 67981113 12
J1
1415161724 23 22 21 20 19 1826 25
WELD CONTROLLER
W05X0233
(SCHEMATIC:
X0233)
METER BOARD
W05X0207
(SCHEMATIC:
X0207)
W1
W2
HF1
HF2
HF TRANSFORMER -
+
INPUT BOARD
W05X0203
(SCHEMATIC:
X0203)
INVERTER BOARD
W05X0190
(SCHEMATIC:
X0190)
1
34
2
T1
GAS
SOLENOID
W07X0262rev03
WARNING: HIGH VOLTAGE CAN KILL
* Do not operate with covers removed.
* Disconnect input power by unplugging
power cord before servicing.
* Do not touch electrically live parts.
* Only qualified persons should install,
use or service this machine.
*
(SCHEMATIC: X0322)
W05X0322
REMOTE BOARD
J1
JP1
EARTH
*
RIBBON CABLE
Y/G
DISPLAY BOARD
W05X0370
(SCHEMATIC: X0370)
OR
GREEN
WIRING DIAGRAM CODE 11032
NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside the
machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number.
"#('
*(
WARNING
AVISO DE
PRECAUCION
ATTENTION
WARNUNG
ATENÇÃO
Spanish
French
German
Portuguese
Japanese
Chinese
Korean
Arabic
READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE
CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE
ESTE EQUIPO Y LOS CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU
SUPERVISOR.
LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT
ET LES PRODUITS A ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE
EMPLOYEUR.
LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRO-
DENEINSATZ DES HERSTELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS
SIND EBENFALLS ZU BEACHTEN.
•Do not touch electrically live parts or
electrode with skin or wet clothing.
•Insulate yourself from work and
ground.
•No toque las partes o los electrodos
bajo carga con la piel o ropa moja-
da.
•Aislese del trabajo y de la tierra.
•Ne laissez ni la peau ni des vête-
ments mouillés entrer en contact
avec des pièces sous tension.
•Isolez-vous du travail et de la terre.
•Berühren Sie keine stromführenden
Teile oder Elektroden mit Ihrem
Körper oder feuchter Kleidung!
•Isolieren Sie sich von den
Elektroden und dem Erdboden!
•Não toque partes elétricas e electro-
dos com a pele ou roupa molhada.
•Isole-se da peça e terra.
•Keep flammable materials away.
•Mantenga el material combustible
fuera del área de trabajo.
•Gardez à l’écart de tout matériel
inflammable.
•Entfernen Sie brennbarres Material!
•Mantenha inflamáveis bem guarda-
dos.
•Wear eye, ear and body protection.
•Protéjase los ojos, los oídos y el
cuerpo.
•Protégez vos yeux, vos oreilles et
votre corps.
•Tragen Sie Augen-, Ohren- und Kör-
perschutz!
•Use proteção para a vista, ouvido e
corpo.
WARNING
AVISO DE
PRECAUCION
ATTENTION
WARNUNG
ATENÇÃO
Spanish
French
German
Portuguese
Japanese
Chinese
Korean
Arabic
LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES
DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
•Keep your head out of fumes.
•Use ventilation or exhaust to
remove fumes from breathing zone.
•Los humos fuera de la zona de res-
piración.
•Mantenga la cabeza fuera de los
humos. Utilice ventilación o
aspiración para gases.
•Gardez la tête à l’écart des fumées.
•Utilisez un ventilateur ou un aspira-
teur pour ôter les fumées des zones
de travail.
•Vermeiden Sie das Einatmen von
Schweibrauch!
•Sorgen Sie für gute Be- und
Entlüftung des Arbeitsplatzes!
•Mantenha seu rosto da fumaça.
•Use ventilação e exhaustão para
remover fumo da zona respiratória.
•Turn power off before servicing.
•Desconectar el cable de ali-
mentación de poder de la máquina
antes de iniciar cualquier servicio.
•Débranchez le courant avant l’entre-
tien.
•Strom vor Wartungsarbeiten abschal-
ten! (Netzstrom völlig öffnen;
Maschine anhalten!)
•Não opere com as tampas removidas.
•Desligue a corrente antes de fazer
serviço.
•Não toque as partes elétricas nuas.
•Do not operate with panel open or
guards off.
•No operar con panel abierto o
guardas quitadas.
•N’opérez pas avec les panneaux
ouverts ou avec les dispositifs de
protection enlevés.
•Anlage nie ohne Schutzgehäuse
oder Innenschutzverkleidung in
Betrieb setzen!
•Mantenha-se afastado das partes
moventes.
•Não opere com os paineis abertos
ou guardas removidas.
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
• World's Leader in Welding and Cutting Products •
