Line 6 Digital Wireless 91699TX95 900MHz ISM Band Digital Audio Transmitter User Manual manual

Download:
Mirror Download [FCC.gov]
Document ID	723002
Application ID	LiyOdLWvRowiMG2gQMl91w==
Document Description	manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.82kB (260285 bits)
Date Submitted	2006-10-31 00:00:00
Date Available	2006-10-31 00:00:00
Creation Date	2006-10-11 16:48:23
Producing Software	Mac OS X 10.4.8 Quartz PDFContext
Document Lastmod	2006-10-11 16:48:23
Document Title	manual

Digital Wireless Systems
Digital UHF Wireless System
Model XDS95
Users Guide
Includes easy setup instructions for single and
multi-system operation
PLEASE RECORD UNIT SERIAL NUMBER INDICATED ON THE REAR PANEL FOR FUTURE REFERENCE
Serial No:
Introduction to the XDS95 Digital UHF Wireless
Created specifically for performing and recording musicians who demand
to be untethered without compromising their sound, the XDS95 24-bit digital wireless system delivers your tone and performance with the sound
and feel of a direct wire connection.
X2's proprietary digital technology provides superior fidelity while the XDS95’s "stomp-box" style
receiver houses a micro-processor that selects the digital data stream from among the four internally
mounted Q-diversity™ antennas to eliminate dropouts and interference including DTV. You’ll enjoy
the sound and performance of a direct wire connection free from compander ICs and the associated
'pumping' and 'breathing' that squashes your tone, and other problems associated with analog
wireless technology.
Operating the system is unlike any wireless you've tried before. Simply connect the transmitter to
the source via the 1/8" threaded-collar locking connector and the "stomp-box" style receiver to your
amplifier, mixer or pedal-board. Then power up making sure the transmitter and receiver are set to
the same channel. That's it. You're ready to go! No knobs to adjust and no antennas to loose or
break mean you're up and running in the time it would take to connect a cable.
About the XDS95 Digital Wireless System
All of this sound and performance is provided to you with an incredible feature set including:
• 24-bit digital converters yield 117 dB dynamic range to capture your most expressive performances
• Frequency Clear™ UHF Digital - a proprietary digital signal on a 900 MHz UHF carrier for freedom
from multipathing and interference, including DTV
• Five user-selectable channels (all five are fully compatible for simultaneous use)
• Auto-DigiScan™ to confidently select an open channel
• Frequency response all the way down to 20 Hz for truly thundering lows
• Stereo 1/4" output for instrument and full-bandwidth or 'tuner out' applications
• Five segment LED display (battery status, link status, audio level, RF level and channel)
With the XDS95 Digital UHF Wireless System you'll have the freedom and sound to deliver your most
expressive performance every time without any hassles or complicated setup procedures.
To familiarize you with your new digital wireless system, we suggest that you read through this entire
operation manual.
System Components
System includes:
• XDR1 Digital UHF Receiver
• XDT1 Digital UHF Transmitter
• 2 9v Alkaline Batteries
• 1/4” to 1/8” locking connector instrument cable
Optional Accessories:
• Power supply for XDR1
XDS95 Digital UHF System Features
XDR1 Digital UHF Receiver
LED Display
• See system setup on page 5.
AC Adapter Jack (Adapter is optional)
• 9V 300mA
1/4” Mono/Stereo Output
• See system setup on page 5.
Mode/Channel Select Button
• See system setup on page 5.
Power Switch
• Press once to turn the power to the receiver
on, and once more to turn the power off.
9V Battery Compartment
• Battery compartment is secured with
two screws.
XDT1 Digital UHF Transmitter
LED Display
• See system setup on page 4.
Mode/Channel Select Button
• See system setup on page 4.
Power Switch
• Press once to turn the power to the transmitter
on, and once more to turn the power off.
Metal Belt Clip
• Fastens transmitter securely to belt or
guitar strap.
1/8” Mono Instrument Input (cable included)
• 1/4” to 1/8” locking connector.
9V Battery Compartment
• Battery compartement snaps in to place.
Setting Up Your Transmitter
Power Up Procedure
Press on/off button to turn unit on. LEDs will cycle blue-red-blue on power
up sequence.Once unit is powered on the unit will display current channel
number with a blue LED and battery life with a red led by continuously
toggling between the two LEDs.
As the user inputs audio into the unit the LEDs automatically become an
audio level indictor where blue LEDs are displayed from left to right as
the audio level increases. LED #5 will light red during audio display if the units input reaches a
maximum level. After a few seconds pause in audio input the unit switches back to channel/battery
display mode.
Channel Selection
There are 5 different frequency channels which you can choose to
transmit and receive data, they are labeled 1-5 on both transmitter and
receiver. In order to operate on any one of these channels, you must have
both the transmitter and receiver on the same channel number. In order to
change the transmit frequency push the channel button, the unit will then
increment and display the channel number with a blue LED each time the
user presses the button down. Continue this until the desired channel
number is reached. The unit will then go back to the toggling LED mode to display battery life and
channel number.
Transmitter Battery Metering
The battery is displayed on the tranmitter as follows: LED #5 (furthest to
the right looking at the front of the unit) means 5hrs or greater of battery
life remaining. As the battery expires the unit will change the red leds to
#4 for 4hrs, #3 for 3hrs, etc.. Once the unit has less than 1hr left of battery
life the #1 LED will then blink at a high rate until the battery expires. This
alerts the user to the need of battery replacement.
Power Down Procedure
To turn the unit off press and hold the on/off switch until the LEDs flash a red/blue alternating
pattern then release the on/off button. The unit will then power down. all LEDs off indicate power
down is complete.
Connecting the System
Plug your instrument into the transmitter with the provided cable. Next, connect the output of the
receiver to the input of your effects pedal, amplifier, recording device, etc.. When using a standard
1/4” (mono) cable, the receiver will output audio signal optimized for instrument applications. When
using a stereo 1/4” (TRS) cable, the tip sends instrument out, the sleeve sends full-bandwidth signal. This can be used as a “tuner out” or “direct out” for interfacing with a variety of devices.
PLEASE NOTE: when using “full bandwidth” for typical instrument/amplifier setups there will be a
noticeable increase in high frequency response. High frequencies are not boosted by the system,
rather, they are allowed to “pass through”.
Setting Up Your Receiver
Power Up Procedure
Press on/off button to turn unit on. LEDs will cycle blue-red-blue on power
up sequence. Once unit is powered on the unit will display current channel
number with a blue LED and battery life with a red led.
The unit will automatically scan for your digital RF signal. This is indicated
by the blue LEDs cycling back and forth 1-5 then 5-1. After each cycle, the
unit will stop on the current red batt life LED then blink the current blue
channel LED. The unit will stay in this mode until a transmitter is turned on and transmitting on the
same channel. Once the link is established and the receiver is receiving data, the unit will display
current channel number with a blue LED and battery life with a red LED by continually toggling
between the two LEDs.
As the user inputs audio into transmitter and sends it to the receiver unit, the LEDs on the receiver
become an audio level indictor. Blue LEDs are displayed from left to right as the audio level
increases. LED #5 will light red during audio display if the unit’s input reaches a max level. After
a few seconds pause in audio input the unit switches back to channel/battery display mode.
Channel Selection
There are 5 different frequency channels which
you can choose to transmit and receive data,
they are labeled 1-5 on both transmitter and
receiver. In order to operate on any one of these
channels, you must have both the transmitter and
receiver on the same channel number. In order to
change the receive frequency, push the channel
button. The unit will then increment and display the channel number with a blue LED each time the
user presses the button down. Continue this until the desired channel number is reached. The unit
will then go back to the mode displaying battery life and channel number.
Receiver Battery Metering
the battery is displayed on the receiver as follows: LED #5(furthest to the
right looking at the front of the unit) means 5hrs or greater of batt life
remaining. As the battery expires the unit will change the red LEDs to #4
for 4hrs, #3 for 3hrs, etc.. Once the unit has less than 1hr left of battery life
the #1 LED will then blink at a high rate until the battery expires. This
alerts the user to the need of battery replacement.
Power Down Procedure
To turn the unit off press and hold the on/off switch until the LEDs flash a red/blue alternating
pattern then release the on/off button the unit will then power down. all LEDs off indicate power
down is complete.
Additional Information
Multi-system Operation
Up to five systems can operate simultaneously. In situations where it is necessary to have more than
one person wireless, each transmitter and receiver combination must be set to the same channel. Set
the first system to transmit and receive on channel “one”, the second system to transmit and receive
on channel “two”... and so on.
DigiScan™ Special Receiver Power Up Mode
While holding down the channel select button on the receiver, push the on/off button and release.
Continue to hold the channel select button until the LEDs are all solid red. Then release the channel
select button. The unit will now do a RF scan on all 5 frequencies. While in this mode the receiver
will continue to scan and report. If the channel has no RF signal then a blue LED will light for the
corrosponding channel number. If there is currently RF in the channel the LED will be red. Blue
LEDs mean channel is clear red means the channel is not clear. To enter regular operating mode
push and hold down the on/off button until the unit enters the normal mode.
Optimizing Your Wireless Performance
Place the receiver on or near the desired amplification system, pedalboard or with your effects pedals. FOR BEST RESULTS, PLACE RECEIVER HIGH ABOVE ANY OBSTRUCTIONS, as the system works best when transmitter and receiver are in line of sight.
Battery Life Information
Fresh Alkaline batteries should last about 8 hours, NiCad rechargeable batteries will only last about
4.5 hours. Standard batteries are not recommended. THE BATTERY HOUR DISPLAY WILL ONLY
BE ACCURATE FOR ALKALINE BATTERIES. The battery life is calculated inside the each component and displayed in 1 hour increments. Upon power up the battery info will take about one minute
to stabilize, the battery gauge is then accurate within + or - 30 min. You may use batteries until they
are completely drained without affecting the performance of the unit in any way.
Warranty Information
X2 will repair or replace any defective system within the first two years free of charge. X2 will cover 2day return shipping costs in the continental United States. This warranty is transferrable, but does not
cover abused systems. Terms and conditions subject to change without notice. Please retain a copy
of your dated sales receipt for proof of warranty status should repairs become necessary.
Warning:
Changes or modifications not expressly approved in writing by X2 Corporation may void the users
authority to operate this equipment.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Q-Diversity™,FrequencyClear™ and DigiScan™ are trademarks of X2 Corportion.
XDS95 PATENTS PENDING.
© 2006 X2 CORPORATION
Troubleshooting
Symptom
Cause
Solution
No sound
System not turned on.
Improper connection or
improper channel
selection.
Check that the system is powered
on. Check that the transmitter and
receiver are set to the same operating channel. Check that the receiver
is receiving data. Check that the
source is operating correctly. Check
that the receiver displays audio
level. Check connections.
Intermittent sound or
distortion
Improper source
performance. Improper
connection. Multiple
transmitters are set to
the same operating
channel. Transmitter
has gone out of range.
Transmitting through
metal wall. Unknown
source of RF in local
vicinity.
Check source. Check connections.
Turn your transmitter off. Check to
see if receiver still displays data
being received. If so, locate and
either turn off or switch channels on
extra transmitter. Adjust receiver
positioning closer to transmitter.
Check that other local communication systems are not interfering with
your performance. They will most
likely be within close proximity to
receiver.
Refer All Servicing to X2
We believe that the D95 is one of the most reliable wireless systems that can be made using current
technology, and should provide years of trouble-free use. However, should problems occur, DO NOT
attempt to service the unit yourself. Service on this product should only be performed by X2. THERE
ARE NO USER SERVICEABLE PARTS INSIDE.
Obtaining Repair Service
Before contacting X2, check over all your connections, and make sure you’ve read the manual. Your
X2 dealer may be able to offer further assistance. If the problem persists, call X2 at 916-779-1040
and request the customer service department. Talk the problem over with one of our technicians; if
necessary, you will be given a return authorization (RA) number and instructions on how to return
the unit. All units must be shipped prepaid and COD shipments will not be accepted. For prompt
service, indicate the RA number on the shipping label. Tape a note to the top of the unit describing
the problem, include your name and phone number where X2 can contact you if necessary, as well
as instructions where you want the system returned. X2 will pay for 2nd-day shipping back to you on
any repair covered under the terms of this warranty.
Service address for customers in the USA:
X2 Corporation
4630 Beloit Drive, Suite 20
Sacramento, CA 95838
Specifications
Overall System Specifications
Transmission Format:
X2 proprietary digital audio transmission
Frequency Response:
20 Hz - 12 kHz
Audio Dynamic Range:
>117 dB
Distortion:
0.03% THD
RF Carrier Frequency:
902 MHz to 928 MHz, FSK
Selectable Frequencies:
Five
RF Output Power:
10mw
Audio Output Level:
Unity gain with transmitter input
Polarity:
Positive voltage at input yeilds positive voltage at output
Transmission Range:
>150 feet line-of-sight (may vary due to local conditions)
FCC Approval:
Part 15 approved, no user-license required
XDT1 Transmitter Specifications
A/D Conversion:
24-bit Delta Sigma, 128 times over sampling
Input Impedance:
1.3 M-Ohm
Connectors:
1/8" Unbalanced locking connector
Controls:
Power On/Off, Channel Select
LED Display:
Five segment - Power On, Channel, Battery Life,
Audio Level Meter
Dimensions:
2.4" W x .66" D x 4" H
Battery Life:
Switching power supply, ~8 Hours (9v alkaline)
Weight:
.25 lbs (with 9v battery installed)
XDR1 Receiver Specifications
D/A Conversion:
24-bit Delta Sigma, 128 times over sampling
Output:
2.12V RMS (Unbalanced: 7K-Ohm)
Connectors:
1/4" Unbalanced stereo output, tip= instrument voicing,
sleeve= full bandwidth
LED Display:
Five segment - Power On, Data Link, Channel, Battery Life,
Audio Level Meter, RF Strength
Controls:
Power On/Off, Channel/Mode Select
Dimensions:
3.078" W x 1.17" D x 4.7" H
Power Requirements:
9V DC via battery or optional AC power supply
Weight:
.45 lbs (with 9v battery installed)
X2 Corporation • 4630 Beloit Drive, Suite 20 • Sacramento, CA 95838

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 8
Create Date                     : 2006:10:11 16:48:23-07:00
Modify Date                     : 2006:10:11 16:48:23-07:00
Producer                        : Mac OS X 10.4.8 Quartz PDFContext

EXIF Metadata provided by EXIF.tools