Line 6 Pod Hd Desktop Owners Manual POD® Advanced Guide (v2.0, Rev. A)

2014-07-19

: Line-6 Line-6-Pod-Hd-Desktop-Owners-Manual line-6-pod-hd-desktop-owners-manual line-6 pdf

Open the PDF directly: View PDF .
Page Count: 113 [warning: Documents this large are best viewed by clicking the View PDF Link!]

POD® HD Advanced Guide
Overview
System Setup
Features & Functionality
Set Lists & Presets
FX Edit Mode
- Accessing FX Edit Mode
Amp, Cab & Mic Models
FX Models
Looper Mode
- Looper Controls & Performance View
- Looper Settings
USB Audio
Appendix A: Line 6 Monkey
- Launch Line 6 Monkey
- Grab Those Updates
Appendix B: FBV Foot Controllers

POD® HD

An in-depth exploration of the features &

functionality of POD HD.

Electrophonic Limited Edition

Advanced Guide

Table of Contents

Overview ................................................................................. 1•1

Home Views ................................................................................................... 1•1

Tuner Mode .................................................................................................... 1•4

Tap Tempo ...................................................................................................... 1•5

Connections ................................................................................................... 1•5

POD HD Edit Software .................................................................................. 1•6

System Setup ......................................................................... 2•1

Accessing System Setup ................................................................................. 2•1

Page 1, Setup:Utilities Options ..................................................................... 2•2

Page 2, Setup:Utilities Options ..................................................................... 2•3

Page 3, Setup: Input Options ......................................................................... 2•4

Page 4, Setup: Output Options ...................................................................... 2•7

Page 5, Setup: S/PDIF Output Options ......................................................... 2•9

Page 6, Tempo Options ................................................................................ 2•10

Features & Functionality ....................................................... 3•1

FX Blocks ....................................................................................................... 3•1

Mixer Block .................................................................................................... 3•3

Moving FX Blocks .......................................................................................... 3•4

Tweak Knob Assignment ............................................................................... 3•6

FX & Amp Block FS Assignment .................................................................. 3•7

Dynamic DSP ................................................................................................. 3•8

Set Lists & Presets ................................................................. 4•1

Working with Set Lists ................................................................................... 4•1

Working with Presets ..................................................................................... 4•4

Saving Presets ................................................................................................. 4•5

FX Edit Mode ......................................................................... 5•1

Accessing FX Edit Mode ................................................................................ 5•1

Amp, Cab & Mic Models ........................................................ 6•1

Amp Model Positioning ................................................................................. 6•1

Selecting Amp, Cab & Mic Models .............................................................. 6•3

Editing Amp Parameters ................................................................................ 6•6

Amp & Cab Edit Display ............................................................................... 6•7

Amp/Preamp Models ................................................................................... 6•12

Cab Models ................................................................................................. 6•14

FX Models ............................................................................... 7•1

Dynamics Models ........................................................................................... 7•1

Distortion Models .......................................................................................... 7•2

Modulation Models ........................................................................................ 7•3

Filter Models .................................................................................................. 7•5

Pitch Models .................................................................................................. 7•6

Preamp+EQ Models ....................................................................................... 7•9

Delay Models ................................................................................................ 7•10

Reverb Models ............................................................................................. 7•11

Volume/Pan & Wah Models ........................................................................ 7•13

Looper Mode .......................................................................... 8•1

Looper Controls & Performance View .......................................................... 8•1

Looper Settings .............................................................................................. 8•5

USB Audio .............................................................................. 9•1

The Line 6 USB Audio Driver ...................................................................... 9•1

The Line 6 Audio-MIDI Devices Panel ........................................................ 9•3

Mac® - Line 6 Audio-MIDI Devices ............................................................. 9•3

Windows® - Line 6 Audio-MIDI Devices ..................................................... 9•8

Line 6, POD, FBV, CustomTone and Line 6 Monkey are trademarks of Line 6, Inc. All other product names, trademarks and artists’

names are the property of their respective owners, which are in no way associated or afﬁliated with Line 6. Product names, images, and

artists’ names are used solely to identify the products whose tones and sounds were studied during the Line 6 sound model development for

this product. The use of these products, trademarks, images, and artists’ names does not imply any cooperation or endorsement.

Appendix A: Line 6 Monkey ................................................. A•1

Launch Line 6 Monkey ................................................................................. A•1

Grab Those Updates ..................................................................................... A•2

Appendix B: FBV Foot Controllers ......................................B•1

FBV MkII & FBV Series Controllers ............................................................. B•1

Setup Options for FBV ................................................................................... B•2

FBV Controller Devices - Footswitch & Pedal Mapping ............................. B•5

FBV Shortboard MkII .................................................................................... B•5

FBV Express MkII .......................................................................................... B•8

FBV Longboard ............................................................................................ B•10

FBV Shortboard ........................................................................................... B•13

Expression Pedal Assignment ...................................................................... B•16

Amp & FX Block Footswitch Assignment .................................................. B•18

Set List Select .............................................................................................. B•21

Tap Tempo .................................................................................................... B•22

Tuner Mode .................................................................................................. B•22

Overview

1•1

Overview

Welcome to the POD® HD Advanced Guide. This guide contains in-depth details of the

POD HD features and functionality. Please be sure to also read through your POD HD

Pilot’s Handbook for basic info on POD HD and this Guide will take it from there! In

this chapter, we’ll present an overview of the main screens and features to get you started.

This Guide covers POD HD with Flash Memory version 2.0 (or later) installed. Please use

Line 6 Monkey to check for and install the latest updates for your device - see “Appendix

A: Line 6 Monkey” on page A•1.

Home Views

SAVE

HOLD FOR SYSTEM & I/O

VIEW

The place to start is in one of the Home View screens. Press the VIEW button to

rotate through the available Home Views. While in any of these Home View

screens, you can turn the PRESETS knob and call up a Preset in the current

Setlist, or push the PRESETS knob to select from among other Set Lists!

Signal Flow View

The Signal Flow View displays all Amp & FX “Blocks” and their ordering for the current

Preset. As you’ll see in several of the following chapters, this is the screen where you’ll

“select” the desired Block to perform other actions, such as choose a new Amp or FX

Model, edit its parameters, move its position, and more.

Use the and Nav.

Pad buttons to select the

desired Block

Currently loaded Preset

location and title

FX Blocks within

“Pre” position

FX Blocks within

“Post” position

Amp Blocks Looper

Parallel Paths A (upper)

and B (lower) with Mixer

Block

The items within the Signal Flow View

The signal ﬂow architecture of each Preset is comprised of 3 main sections where Amp &

FX Blocks can be positioned: Pre, Post and parallel Paths A & B.

Overview

1•2

At the bottom of the Signal Flow View screen, you’ll see up to four parameters that are

accessed using the Multi-function knobs 1-4.

Accessing parameters with the Multi-select Knobs

These parameters are speciﬁc to the currently selected Block and allow you to choose new

Models & edit parameters. Or, you can dive deeper in the Edit Mode and access additional

settings in other screens, as covered in the following chapters.

Big User View

This screen simply provides you with one BIG display of the currently loaded Preset

number - convenient for dark stages!

The Big User View

Overview

1•3

Performance View

This screen displays the functions available for your POD HD A, B, C & D buttons and

for Line 6 FBV™ Controller functions, if one is connected. This screen appears in three

different variations, depending on your device settings. The four options on the lower half

of the screen pertain to the A, B, C & D buttons (and to FBV footswitches A - D).

You’ll see one of the following screens appear, dictated by the current POD HD Setup - FS

MODE setting - Also see “Page 1, Setup:Utilities Options” on page 2•2 for details.

“FS 5-8” Mode“ABCD” Mode

When POD HD is in Looper Mode, a 3rd variation of the screen displays the Looper

functions that are accessed by the A, B, C & D buttons and FBV footswitches. Also see

“Looper Controls & Performance View” on page 8•1.

The Performance View with Looper Mode active

Overview

1•4

Tuner Mode

To enter Tuner mode, press and hold the TA P button. A few options are available, adjusted

using the Multi-function knobs.

The Tuner screen

Note that the Tuner receives a signal only from the POD HD Input 1 source.

Pluck an individual string on your guitar and you’ll see the name of the note displayed.

When the graphic bar is to the left of center, your string is ﬂat; when it is to the right, your

string is sharp. When the bar is within the center range, triangles will appear above and

below it, indicating your string is in tune.

• Reference (Knob 1): If you’d like to tune to a reference other than standard 440Hz,

select from 425 to 455Hz.

• Audio (Knob 2): Select Mute to silence POD HD output while tuning, or select

Bypass to hear your guitar dry.

Press the TA P switch, or any other button, to exit Tuner Mode.

Overview

1•5

Tap Tempo

Tap Tempo is the term we use to refer to the “System Tempo” value that is

accessed via the TA P button on your POD HD device. Tap rhythmically to set

your Tempo. Alternatively, you can set a numerical Tempo value within Setup

(see “Page 6, Tempo Options” on page 2•10). This setting is saved per Preset.

You’ll see the TA P switch blink to indicate your current Tap Tempo BPM (if your Tap LED

option is set to “On” - see “Page 2, Setup:Utilities Options” on page 2•3). Tempo-based

FX (Modulation, Filter & Delay FX) that offer a Tempo Sync parameter can optionally be

set to a note division of this Tap Tempo value.

Connections

Please refer to your POD HD Pilot’s Guide for descriptions of the Input & Output

connections. You’ll ﬁnd more details on their speciﬁc uses within the following chapters

as well!

Overview

1•6

POD HD Edit Software

Be sure to visit line6.com/software to download the Line 6 POD® HD Edit software - the

free patch editor/librarian for Mac® and Windows® computers. Using POD HD Edit and

a USB connection you can easily create, audition, customize, backup/restore and save an

unlimited number of Tone Presets for your device.

The POD HD Edit application

System Setup

2•1

SyStem Setup

In this chapter, we’ll cover the options for conﬁguring your POD® HD system settings.

Note that some System Setup options are “global” settings (they persist always, regardless of

the current Preset) while others are saved individually per Preset, as noted in the following

sections. You’ll want to be sure to save your Preset after changing settings of the latter type

in order to retain them. To restore all global settings to their factory default value, hold

down the Nav. Pad - left arrow button while powering on POD HD.

Accessing System Setup

To access the System Setup options, press and hold the VIEW button. Here you can

conﬁgure several device functions, Input & Output settings and more.

SAVE

HOLD FOR SYSTEM & I/O

VIEW

Use the Nav Pad buttons to navigate through the several Setup pages.

System Setup

2•2

Page 1, Setup:Utilities Options

The top portion of the screen lists the Flash Memory and USB Firmware versions currently

installed on your POD HD device. The lower portion of the screen offers four options,

adjustable using the Multi-function Knobs 1 - 4.

• Footswitch Mode (Knob 1): This option applies to your POD HD A, B, C & D.*

You’ll see your Performance View screen reﬂect the functions of these buttons

according to the mode selected here (see “Performance View” on page 1•3). This

setting is global.

• In “ABCD” Mode: The A, B, C & D buttons recall the current Bank’s Presets

A-D.

• In “FS 5-8” Mode: The A, B, C & D buttons toggle the Footswitch 5-8 assigned

Models On/Off.

*Note: This also applies to a connected Line 6 FBV™ Controller’s A, B, C & D footswitches

- please see “Setup Options for FBV” on page B•2.

• Amp Knobs Display (Knob 2): When set to “On,” allows the LCD screen to

momentarily display the actual Amp Tone Knob values whenever adjusting any

physical amp knob. This setting is global.

• Looper FS Display (Knob 3): When Looper Mode is active, this option determines

how and when the Looper screen is displayed (see page 8•1). This setting is global.

• All Views: When Looper Mode is On, the Looper screen is always displayed.

• Performance View: When Looper Mode is On, displays the Looper screen, or the

other Performance View (Signal Flow or Big User) screens, by toggling the VIEW

button. This option can be useful for referencing your Presets or adjusting Models

while Looping.

System Setup

2•3

• Trails (Knob 4): When set to “On,” allows the echo repeats and/or decay of Delay

and Reverb FX to continue when the Model is toggled Off. With the Trails option

“Off” the decay is muted instantly when toggling the Model Off. This setting is

saved per Preset. (Note that this feature does not provide a “spillover” of the FX

decay when changing Presets.)

Page 2, Setup:Utilities Options

The options at the bottom of the screen are as follows - all are global settings.

• LCD Contrast (Knob 1): Adjusts the screen’s contrast.

• Tap Tempo LED (Knob 2): Choose “On” to have the LED light for the TAP switch

(or connected FBV TA P footswitch) ﬂash to indicate the current Tap Tempo value.

Choose “Off” to have it remain unlit.

• AC Frequency (Knob 3): All HD Amp Models include simulation of AC hum, typical

of the AC Vacuum Tube Heater component - an important part of the tonality of

a tube ampliﬁer. Set the AC Rate to match that of the USA (60Hz) or UK (50Hz)

frequency for authenticity. (This setting may be subtle depending on the current

Amp Model settings, and may be more apparent when synchronizing this setting

with the AC rate of any tube ampliﬁer that POD HD may be plugged into.)

• FBV Express (Knob 4): This option applies only to a connected Line 6 FBV

Controller. It should only be set to “On” speciﬁcally for a FBV Express MkII model

device. Please see “Setup Options for FBV” on page B•2.

System Setup

2•4

Page 3, Setup: Input Options

The Inputs Setup page allows you to select which of the device’s audio inputs are used as

the “source” – sort of like a built-in, programmable patchbay. There is also a control which

adjusts the Guitar input impedance.

• Input 1 and Input 2 Source (Knobs 1 & 2) - Select the physical input(s) that you

want to be the “source” which feeds into the signal path. Note that you can choose

different Sources to independently feed each signal path, or choose Same to feed a

common Source into both paths.

• Guitar In-Z - Select the input impedance of the Guitar input. This feature affects

tone and feel because your guitar pickups are being loaded as they would be by an

effect pedal or a tube ampliﬁer.

Note: The Guitar In-Z setting affects the GUITAR IN input only. Please see the Impedance

Ratings table at the end of this section to reference the input impedance of each individual

model.

• The Auto option dynamically sets the input impedance to match the input

impedance of the very ﬁrst Amp or FX model in your POD HD signal chain.

• Or, you can manually select from a variety of impedance values from low to high

(22k,32k,70k,90k,136k,230k,1M,or3.5M).Alowervaluewilltypicallyresult

in some high frequency attenuation, lower gain and overall “softer” feel. A higher

value provides full frequency response, higher gain and overall “tighter” feel.

• Inputs Setup -Determines whether theother 3options in thisInputs screenare

applied per Preset, or globally.

• Preset - Recalling a preset will load the Input 1 Source, Input 2 Source and Guitar

In-Z parameter settings as last saved with the individual preset.

System Setup

2•5

• Global - Once the “Global” option is selected here, the other three Input options’

valuesonthisSetuppage(InputSources1and2,andGuitarIn-Z)areutilized

globally, regardless of their values that are saved with each individual preset. The

Input values you choose on this Setup page are then retained independently for

the Inputs Setup - Global option. When you change the Inputs Setup back to

“Preset,” the Input options’ values saved with each individual preset are once

again utilized.

Note: Saving a preset while this option is set to “Global” will write the current global

Inputs and Guitar In-Z values to the individual, saved preset.

Amp & FX Model - Guitar Input Impedance Ratings

Model Guitar Input Impedance

(Ohms)

Amps & Preamps

All Amp & Preamp Models 1M

Distortion FX

Screamer 230k

Color Drive 136k

Buzz Saw 230k

Facial Fuzz 22k

Jumbo Fuzz 90k

Fuzz Pi 22k

Octave Fuzz 230k

All Other Distortion Models 1M

Dynamics FX

All Dynamics Models 1M

Modulation FX

Dual Phaser 230k

U-Vibe 90k

Analog Choruis 22k

All Other Modulation Models 1M

System Setup

2•6

Amp & FX Model - Guitar Input Impedance Ratings

Model Guitar Input Impedance

(Ohms)

Filter FX

All Filter Models 1M

Pitch FX

All Pitch Models 1M

Delay FX

Multi Head 22k

Analog Echo 230k

Analog w/Mod 90k

All Other Delay Models 1M

Preamp + EQ FX

All Preamp & EQ Models 1M

Reverb FX

All Reverb Models 1M

Wah FX

Weeper 90k

All Other Wah Models 1M

Volume & Pan FX

All Volume and Pan Models 1M

FX Loop

FX Loop 1M

About Source Input Signal Routing

ItisimportanttonotehowPODHDactuallyroutesSourceInputs1and2throughAmp

& FX Blocks that are positioned “Pre” position. The following behaviors apply:

• In a conﬁguration with no Amp or FX Blocks in Pre, Input 1 is fed only to Path A

andInput2onlytoPathB.Therefore,thisisthebestcongurationifyouwantto

retain discrete Input Sources into Paths A & B.

System Setup

2•7

• Placing an Amp Block or an active mono FX Model in Pre results in a “summing”

ofInputSources1&2,feedingthesame,combinedsignalintothesePre-positioned

Models, and thus into each Path A & B. You may need to adjust your instrument’s

volume level to avoid overloading your Pre-positioned Amp or FX Models.

• Placing a Stereo FX Model in Pre results in the left channel FX output being fed to

Path A and its right output to Path B.*

• The Mixer Block’s Volume and Pan options provide independent control for Path

A & B outputs before they are fed through any Blocks positioned “Post” the Mixer.

• BysettingInput2to“Same,”thiseffectivelyroutesyourInputSourcetobothstereo

Paths A & B (which is how you can feed one guitar input into two Amp Models and/

or parallel FX, for example).

*Please also see “Model Types and Mono/Stereo Signal Routing” on page 3•5 for more

about how mono and stereo FX affect your signal chain.

Page 4, Setup: Output Options

The Mode setting on this page allows you to conﬁgure the type of signal fed to your

POD HD analog outputs to optimize for direct recording versus connecting to an external

ampliﬁer.

Note that this Mode setting affects the signal fed to the POD HD Left & Right main outs,

Headphone outs and USB Record Send.

System Setup

2•8

Knob 1 selects the Output Mode. This is a global setting.

• Studio/Direct: Typically the best option when connecting “Direct” to a mixing

console or recording device. This signal includes “Studio” Cab Models, Mic Model

and an “AIR” convolution to best emulate a mic’ed amp within a room.

• Combo and Stack settings: Optimizes your tone for connecting to an external

ampliﬁer. The signal includes “Live” Cab Models,with no Mic Model or “AIR”

convolution, with a special EQ curve added for each.

• Combo Front & Stack Front: For connecting into the front input of a typical

combo amp or amp head + external cab, respectively. When choosing either of

these Modes, you’ll see these additional options for further tone shaping:

• Lows (Knob 2): Attenuates the low frequencies.

• Focus (Knob 3): Increases the overall midrange.

• Highs (Knob 4): Attenuates the high frequencies.

• Combo Power Amp & Stack Power Amp: For connecting to the power amp of a

combo or head amp.

TIP: When using the Combo or Stack options and connecting into a tube ampliﬁer, we also

recommend that you choose a Preamp Model from the Amp Model menu (rather than one

of the “Full” Amp Models). HD Preamp Models include no power amp emulation, making

them typically better suited for this connection. That said, there is no wrong choice! PODs

have always been about ﬂexibility... Check out all the possibilities and decide which Models

work best for your tone!

System Setup

2•9

Page 5, Setup: S/PDIF Output Options

These options are strictly for conﬁguring the signal fed to the S/PDIF OUT.Usethis24-

bit digital connection when connecting to the S/PDIF input of other devices, such as a

computer audio interface or digital mixing console. All settings are global.

Note: When connecting to another digital device, it is best to clock the external device to

follow POD HD (with POD HD as the “master” device) to maintain proper synchronization

- please see your digital device’s documentation for its digital clock features.

• S/PDIF Output (Knob 1): Selects the type of output mode signal.

• Match Outputs: Uses the setting as conﬁgured on the Setup:Outputs screen - see

page 2•8.

• Dry Input: Your Source Input signal with no Amp, Cab, Mic, “E.R.” or FX

processing applied. (Handy for recording a dry signal in your DAW, to which you

can add a Plug-In or “re-amp” later!)

• Sample Rate (Knob 2):Selectsthesamplerate:44.1kHz,48kHz,88.2kHzor96kHz.

When connecting to another device’s S/PDIF input, always be sure to set both units

to utilize the same sample rate.

• S/P Level (Knob 3): Increases the amplitude of the S/PDIF signal: 0 dB.

System Setup

2•10

Page 6, Tempo Options

• Tempo Sync (Knob 3): The “Speed” or “Time” parameters of all tempo-based FX

(Modulation, Pitch & Delays) can optionally be set to a note value to follow the

(Knob 4) Tempo BPM value. This Tempo Sync option is a global setting that allows

you to choose whether the FX follow the Tap Tempo as a per-Preset value or globally.

• Preset: Tempo settings are saved and recalled on a per Preset basis.

• Global: Tempo information stored within any Preset is ignored. When saving a

Preset while this option is set to “Global,” the current tempo value will be saved

with the Preset.

• Tempo (Knob 4): Enter in a speciﬁc “Tap Tempo” for your current Preset (as opposed

to stomping rhythmically on the TA P button). This value is saved individually per

Preset.

Features & Functionality

3•1

FeatureS & FunctiOnality

Ready to dive deeper? In this chapter, we’ll go into more detail on the major features &

functionality offered on POD® HD.

FX Blocks

For each Preset there is always a total of 8 FX Blocks, each capable of loading any FX

Model. When in the Signal Flow View screen, select any FX Block and you’ll see options

at the bottom of the screen, adjustable using the Multi-Function Knobs 1-4.

The Signal Flow View with an FX Block selected

• Model Type (Knob 1): Select from among the FX Model categories.

• To load no effect in the selected Block, choose “None.” You’ll see the Block

then appear “Null,” as shown below. A Null FX Block can still be moved and

loaded with a new Model at any time. Setting unneeded FX Blocks to None is

a great way to minimize your tone’s DSP usage (see “Dynamic DSP” on page

3•8).

FX Blocks with the Model set to “None”

• FX Model (Knob 2): Choose the desired Model from the Model Type list.

Features & Functionality

3•2

• FX Parameters (Knob 3): Choose from up to 5 adjustable parameters. Alternatively,

double-press the ENTER button to access all the Model’s parameters in one screen -

see “FX Edit Mode” on page 5•1.

• Parameter Value (Knob 4): Adjusts the value for the currently selected parameter.

Each FX Block also offers the following features:

• On/Off: Toggle the FX Block “On” or “Off” by pressing the ENTER button once.

When Off, your signal ﬂows through the FX Block unprocessed.

• Move FX Position: Each FX Block can be moved throughout the signal chain,

providing complete routing ﬂexibility. Place any FX Model before the Amp (“Pre”),

after the Amp (“Post”), or within one of the parallel Paths A & B - see “Amp Model

Positioning” on page 6•1 for details.

• Saved Per Preset: All FX Block positions, their loaded FX Models and all FX

parameter values within the tone are saved with each Preset.

Amp Blocks

A single Amp Block can be placed in the “Pre” or “Post” signal ﬂow positions, or within

parallel “Path A.” Or, two Amps can be used if positioned within Paths A & B, as shown

below. Much like FX Blocks, Amp Blocks can be toggled On/Off and include several

editable parameters. But there’s quite a bit more available for Amps as well, so please refer

to the dedicated chapter “Amp, Cab & Mic Models” on page 6•1 for details!

A Preset with two Amp Blocks

Features & Functionality

3•3

Mixer Block

The Mixer is permanently positioned at the end of the parallel Paths A & B and provides

individual Level and Pan controls for each Paths’ output before fed to the “Post” position.

When the Mixer is selected in the Signal Flow View, its four parameters are available at

the bottom of the screen, accessible using the Multi-function Knobs 1-4.

The Signal Flow View with the Mixer Block selected, showing its 4 parameters

• Volume A (Knob 1): Controls the volume level of the Path A output. 0 dB is unity

gain.

• Volume B (Knob 2): Controls the volume level of the Path B output. 0 dB is unity

gain.

• Pan A (Knob 3): Adjusts the left/right stereo balance of the Path A output.

• Pan B (Knob 4): Adjusts the left/right stereo balance of the Path B output.

Features & Functionality

3•4

Moving FX Blocks

Any of the 8 FX Blocks can be moved throughout your tone’s signal ﬂow, providing

tremendous routing ﬂexibility. To move any FX Block, start within the Signal Flow View

and select the FX Block to be moved. Press the MOVE button and you’ll see the selected

FX Block appear “raised” to indicate it is now moveable.

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

Pressing the Move button to reposition an FX Block

The FX Block can now be moved as follows:

• Use the Nav. Pad buttons to move the FX Block to the desired position.

• Move the FX Block into either Path A or B, and place it before or after an Amp

Model within the path. Use the Nav. Pad buttons to move the FX Block to

the opposite path. This allows you to run your effect in “parallel” and blend the

individual Path A & B outputs using the Mixer’s Level & Pan options!

• Once the FX Block is in the desired position, press the MOVE button again to drop

it into place.

• Amp Blocks can be moved into ﬁxed positions within the Pre or Post signal path

areas, or within the Paths A & B - see “Amp Model Positioning” on page 6•1.

• The Looper can also be selected and moved either to the start (“Pre”) or end (“Post”)

of the signal ﬂow - see “Looper Mode” on page 8•1.

Features & Functionality

3•5

Model Types and Mono/Stereo Signal Routing

It is important to note that some Models (all EQs, Wahs & Volume, and some Modulations,

Filters, Pitches and Delays) preserve a stereo output within the signal chain, while others

(all Dynamics, Distortions, all Amps & Preamps, and other various Models) are mono FX

and do not. The POD HD Inputs 1 & 2 are fed into the signal chain as stereo (see “Page

3, Setup: Input Options” on page 2•4). Therefore, wherever a mono FX or Amp Model

is inserted, the Left & Right channels of this stereo signal is “mono-ized” and heard as a

two-channel mono signal at the Model’s output. To follow are a few examples:

Ping Pong Delay

No mono-output FX or Amp follows Delay

• As shown above, if you place the Ping Pong Delay (a stereo-output FX Model) after

any other FX and/or Amp Models, you’ll hear its delay repeats bounce back and

forth between your Left and Right outputs.

Ping Pong Delay

A Distortion (mono) FX Model follows Delay

Ping Pong Delay

An Amp Model Follows Delay, within same Path

• If you place the Ping Pong Delay immediately before a mono FX Model (as shown

above, left) or Amp Model within the same Path (shown above, right), you’ll hear

its delays “mono-ized,” equally through both the Left and Right outputs.

• The above rules also apply within each of the parallel Paths A and B, since

these are each stereo signal paths as well. The Mixer Block offers Pan controls to

independently adjust the stereo balance of each of these Paths before they are fed

into the ﬁrst “Post” FX (or Amp Block, if the Amp is placed here), immediately

following the Mixer.

• Please also see “Amp Model Positioning” on page 6•1 for additional signal ﬂow

information.

Features & Functionality

3•6

Tweak Knob Assignment

The TWEAK knob on your POD HD utilizes its own “Controller,” allowing it to be assigned

to control just about any Amp or FX parameter (or multiple parameters, simultaneously).

To conﬁgure the TWEAK Controller assignment, select the desired Amp or FX Block,

then double-press the MOVE button to display the Controller Assign screen. These

settings are all saved per Preset.

The Controller Assign screen

• Parameter (Knob 1): Select the parameter for the current Model that you want to

control.* In our example, we’ll choose the Mix parameter for our Delay.

• Controller (Knob 2): Select the TWEAK Controller.*

• Minimum Value (Knob 3): Set the parameter value you’d like for the TWEAK

knob’s minimum value.

• Maximum Value (Knob 4): Set the parameter value you’d like for the TWEAK

knob’s maximum value.

*The EXP 1 & EXP 2 Controller options are used to create assignments for use with Line

6 FBV™ Expression Pedals - see “Appendix B: FBV Foot Controllers” on page B•1.

Features & Functionality

3•7

FX & Amp Block FS Assignment

Any of the FX and Amp Blocks can also be conﬁgured with a “FS” (Footswitch)

assignment to remotely toggle the Block’s Model On/Off. This, of course, is of most use

with a connected FBV Controller device, so we’ve covered this information in “Amp &

FX Block Footswitch Assignment” on page B•18.

It is worth noting here that, when the Setup - FS MODE option (see “Page 1, Setup:Utilities

Options” on page 2•2) is set to “FS 5-8,” your POD HD A, B, C & D buttons will trigger

the FS 5-8 assigned Blocks. To create and edit FS assignments, select the desired FX or

Amp Block within the Signal Flow View, then hold the VIEW button. This displays the

FS ASSIGN screen. All assignments are saved per Preset.

The Footswitch Assign screen - use Knob 1 to create or edit a Block’s FS assignment

Features & Functionality

3•8

Dynamic DSP

We’ve offered up a whole lot of sound possibilities in POD HD, and it can take some

serious Digital Signal Processing (DSP) to run these goodies. Rather than limit your

creative potential with fewer Models or signal routing options, we chose to implement a

“Dynamic DSP” system, which dynamically assigns DSP resources to accommodate your

tone conﬁgurations. When creating a tone that utilizes several heavy-hitting DSP Models,

it is possible to surpass the amount of processing power available. In these cases, you’ll see

the DSP LIMIT REACHED indicator appear, and the current Model is bypassed to allow

your tone to remain active.

Currently selected Model

is automatically bypassed,

with DSP message shown

here

DSP Limit alert is

temporarily displayed

Signal Flow View - displaying DSP Limit alert

In the above example, trying to change the Model for a 2nd Amp placed our tone over

the DSP limit. Therefore, the DSP LIMIT REACHED message is shown temporarily, and

the Amp B Model we selected is automatically bypassed, as indicated by the DSP Over

message. When the DSP Limit is reached, you have a few options to free up DSP resources.

• Try using different Amp Models. Some of the HD Amp Models require more DSP

power than others, so try switching to a different Amp Model.

• Use only one Amp Model rather than two.

• Try toggling Amp and/or FX Models “Off” or set the Block’s Model to “None,” (see

“FX Blocks” on page 3•1). Some FX types, such as Pitch Shifters and Reverbs, utilize

DSP more heavily.

Note: Setting an Amp or FX Block to “None” more substantially reduces the Block’s DSP

usage than toggling its Model to “Off.”

• Once you’re happy with your customized tone, save it so that you can recall it later.

Set Lists & Presets

4•1

Set liStS & preSetS

This chapter covers all you need to know about working with Set Lists and Presets to

manage your POD® HD Tones.

Be sure to also check out the free Line 6 POD HD Edit software. It can be used to create,

customize & manage an unlimited library of POD HD Set Lists & Presets right on your

Mac® or Windows® computer! See “POD HD Edit Software” on page 1•6.

Working with Set Lists

POD HD stores 64 Presets within each of its 8 Set Lists. The big idea here is that you can

load any one of these Set Lists to then gain access to any of its Preset locations - where you

can save your complete settings to, or load a Preset from.

Accessing Set Lists

Push the PRESETS knob to display the Set Lists screen.

SAVE

HOLD FOR SYSTEM & I/O

VIEW

The Set Lists screen

Load a Set List: Use the and Nav. Pad buttons, or turn the PRESETS knob to

select any Set List, then press the ENTER button. This immediately loads the selected

Set List, making all its Presets available. Note that your previously loaded Preset is

automatically closed, and the Preset of the same Bank/Channel location number from

the new Set List is loaded.

Set Lists & Presets

4•2

Rename a Set List: With the desired Set List selected, press the SAVE button to display

the Rename Set List screen.

SAVE

HOLD FOR SYSTEM & I/O

VIEW

To edit the Set List name, use Multi-function Knob 3 to select the desired character,

then use Knob 4 to edit the character. Once complete, press SAVE again to commit

your new name, and you’ll be returned to the Set Lists screen. Or, just press PRESETS

button to return to the Set Lists screen without committing any name changes.

Arranging Presets within Set Lists

While in the Set Lists screen, double-press the ENTER button to display the list of Presets

in the current Set List, where you can reference each Preset’s Bank/Channel location, load

a Preset, or rearrange the Presets into in any order you like.

The Set List - Presets screen

Set Lists & Presets

4•3

Load a Preset: Use the Nav. Pad buttons, or turn the PRESETS knob to select any

of the 64 locations, or use the Nav. Pad buttons to navigate through the list one

Bank at a time. Press the ENTER button to immediately load the selected location’s

Preset.

Move a Preset: Here is an example where we’ll move the “HIWAY 100” Preset from

location 2A to location 2C.

• Select location 2A for the “HIWAY 100” Preset, then press the MOVE button.

You’ll see the selected Preset appear “raised” to indicate it is now moveable:

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

• Use the Nav. Pad buttons or PRESETS knob to select the 2C destination location.

Note that as you select a new Bank/Channel location, the resulting Preset order

is displayed on the screen. For our example, “HIWAY 100” is inserted into 2C,

resulting in the Presets from the original location (2A) to the destination (2C) to

move up one slot:

“Hiway 100” moved from 2A to 2C

• Once you’ve placed the Preset over the desired channel location, press the MOVE

button again to “drop” it into the slot.

Set Lists & Presets

4•4

• Repeat the above steps to rearrange any additional Presets as desired. To commit

all your changes, you must next press the PRESETS button - you’ll see the

“Saving” screen displayed to indicate this process.

The Set List Saving screen

Working with Presets

Each of the 8 Set Lists within POD HD includes 64 Channel locations for holding Presets.

These Set Lists and Presets are all retained in your POD HD internal memory. Each Preset

includes all current FX & Amps in use, all their parameter settings, their position within

the signal ﬂow, footswitch & pedal assignments, Mixer settings, as well as input & output

and other Setup options, as indicated throughout this Guide.

Accessing Presets

From any of the Home View screens, simply turn the PRESETS knob to increment through

the current Set List. The currently loaded Bank/Channel number and Preset name are

displayed at the top of the Home View screen. (Note that you’ll need to save your current

Preset before loading a different one if you wish to retain any changes made!)

SAVE

HOLD FOR SYSTEM & I/O

VIEW

Turn the PRESETS knob to increment through Presets

Alternatively, you can access Presets that reside within any Set List from within the Set

List - Preset screen (see page 4•1).

Set Lists & Presets

4•5

A, B, C & D Channel Buttons

To navigate through Banks & Presets, use the POD HD Bank Up or Bank Down

A, B, C, D buttons to navigate Banks and load a Preset.* (Note that you’ll need to have

the Setup - FS Mode option set to “ABCD” - see “Page 1, Setup:Utilities Options” on page

2•2.)

* If you have a Line 6 FBV™ Controller connected, you can use its footswitches to do the

same - see “Appendix B: FBV Foot Controllers” on page B•1.

• Press the Bank Up or Bank Down button and you’ll see the Queued Bank

screen displayed, with the current Bank/Channel ﬂashing at the top:

The Queued Bank screen - the next Bank is queued

• Continue pressing the Bank Down or Bank Up button and you’ll see the previous/

next Bank’s A, B, C & D Channels & their Presets “queued,” as shown above. Then

press the A, B, C or D button to load the respective Preset from the queued Bank.

Saving Presets

To retain any customization you may have performed on your Preset, or if you want to

rename or move the current Preset, you can use the Save function. Whenever your current

Preset is in an “unsaved” state, you’ll see an asterisk appear in the Signal Flow View.

Asterisk indicating Preset is in an unsaved state

Set Lists & Presets

4•6

Remember to always save your Preset before calling up a different Preset to retain any

changes you may have made!

Press the SAVE button to display the Save Preset screen.

The Save Preset screen

Use the Multi-function Knobs 1-4 to choose your Save functions.

• Set List (Knob 1): Choose any one of the 8 Set Lists here in which you’d like to save

your Preset. By default, you’ll see your currently loaded Set List.

• Destination (Knob 2): Choose the speciﬁc Bank/Channel location within the

selected Set List to save your Preset. Note that this will permanently overwrite the

Preset within the destination location once you commit the save. Choose a location

that contains a “New Tone” to avoid overwriting customized Preset.

• Cursor & Character (Knobs 3 & 4): To rename your Preset, select a character with

Knob 3, then use Knob 4 to edit the selected character.

TIP! For speedy preset naming... The Nav. Disc buttons may be used to move the cursor left

& right. Pressing down clears the currently selected character. Pressing up cycles through

the ﬁrst character of Upper Case, Lower Case, Numeric, and blank.

Once you’ve completed the above settings, press the SAVE button to commit. Or, to

cancel the save, press the PRESETS knob or VIEW button.

FX Edit Mode

5•1

FX edit mOde

Within this chapter, we’ll cover the Edit Mode for FX, which provides access to all editable

parameters for the FX models. (For info on Amp Models, see “Editing Amp Parameters”

on page 6•6.) All changes made in the Edit Mode are saved per Preset.

Accessing FX Edit Mode

First press the VIEW button to display the Signal Flow View screen.

SAVE

HOLD FOR SYSTEM & I/O

VIEW

The Signal Flow View - Modulation FX Block selected

Use the Nav. Pad buttons to select the Block you wish to edit. In our example above,

we’ve selected the ﬁrst Block, which currently has a Modulation Model loaded. While in

the Signal Flow View, you can edit a few options for the selected Block’s FX Model using

the Multi-select Knobs 1 - 4. However, by entering the Edit Mode screen, you’ll have

instant access to all parameters. Double-press the ENTER button to display Edit Mode.

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

The FX Edit Mode - Modulation:U-Vibe FX Model loaded

FX Edit Mode

5•2

Use the Multi-Function Knobs 1- 4 to access the respectively numbered options at the

bottom of the Edit Mode screen.

The Multi-Function Knobs

While the Edit Mode screen is displayed, these knobs access the following functions.

Knob 1 - Type

Select the type of FX Model you want to insert into this Block location. You’ll see the

selected Type displayed at the top of the screen, as well as a handy Model On/Off indicator

at the right.

• None: Choose “None” to remove any FX Model from the Block.

• FX: Choose from the list of FX types.

Knob 2 - Model

Choose the speciﬁc Model for the current FX Type. You’ll see the selected FX Model

displayed at the top of the screen.

FX Edit Mode

5•3

Knob 3 - Parameter

Use the Nav. Pad buttons to select from among the parameters that are displayed. The

“selected” parameter is indicated by the arrow at the left.

Knob 4 - Value

Set the value for the selected parameter.

As shown above, some parameters utilize numerical values, while others utilize a graphical

bar display.

TIP: Most FX parameters can optionally be assigned for Tweak knob or FBV™ Expression

Pedal control! See “Tweak Knob Assignment” on page 3•6.

Amp, Cab & Mic Models

6•1

amp, cab & mic mOdelS

This chapter provides details on selecting & editing the exemplary HD Guitar Amp &

Preamp Models, all of which have been newly developed by our amazing team of sound

engineers for POD® HD! Also covered here are details on Speaker Cabs, Mic Models and

putting Amp Models to use.

Amp Model Positioning

Each Preset includes the ability to run one or two Amp or Preamp Models. Much like

each FX Block, the Amp Block can be repositioned using the MOVE button (please see

“Moving FX Blocks” on page 3•4 ). Here we’ll cover the impact on your signal ﬂow when

placing the Amp in different positions.

*Note: Looking for a Mic Preamp Model? You can ﬁnd the Vintage Pre Model located

within the “Preamps+EQ” category of any FX Block. Having this Preamp Model within

the FX Blocks (rather than in the Amp Blocks) allows you the ﬂexibility of using it with or

without the Amp models, and positioning it anywhere in the signal chain. See “Preamp+EQ

Models” on page 7•9 for more info.

Amps Within Paths A & B

You’ll ﬁnd that a number of the Factory Presets within the “Dual Tones” Set List already

utilize this type of conﬁguration. When moving the single Amp Model into the parallel

Paths A/B from the “Pre” position (before the Path A/B split) or “Post” position (after the

Mixer Block), a 2nd Amp B Block is automatically created in Path B. In this conﬁguration,

the top amp is referred to as Amp A and the other Amp B.

Amp A Amp B

Amp Models within Paths A & B

Behaviors for this conﬁguration are:

• Each Amp Block can be individually set to a different Amp or Preamp Model,*

edited and enabled/disabled.

Amp, Cab & Mic Models

6•2

*Note: Some Amp/Preamp Models utilize more DSP than others. You may ﬁnd it necessary

to bypass or remove some FX Models to enable two simultaneous Amps - see “Dynamic

DSP” on page 3•8 for more info.

• The Amp Blocks cannot be moved within the A or B Paths, however, it is possible

to move any FX Blocks before or after the Amps within either Path.

• Speciﬁc behaviors apply for moving an Amp Block out of the parallel Paths A/B:

• Select Amp A, push the MOVE button, then the Nav. Pad button. This

removes Amp B from the tone and moves Amp A to the Post position, where it

is placed directly after the Mixer (and before any “Post” FX).

• Select Amp A, push the MOVE button, then press the Nav. Pad button. This

removes Amp B from the tone and moves Amp A to the Pre position, where it

is placed just before the Path A/B split (and after any “Pre” FX).

• For the above actions, pressing MOVE when Amp B is selected has no function.

Amp Block in Pre or Post Positions

Only a single Amp Block can be used within either of these positions.

Amp A

Amp in “Pre” position (before Path A & B)

With the Amp in Pre, as shown above, the single amp feeds both Paths A & B. You can

always move FX into either Path A or B, in which case they’ll behave as “Post Amp” FX,

yet be in parallel, with each Path’s output controlled by the Mixer’s A & B Level and Pan.

Note that when utilizing both Inputs 1 & 2 (or when using “SAME” for either of these

Input options) the two Input signals are combined to allow them to be fed into any Amp or

mono FX Model within the Pre position, which can result in a hot signal level. Reduce your

instruments’ volume as needed to avoid overloading your Pre Models.

Amp, Cab & Mic Models

6•3

Amp A

Amp in “Post” position (after Path A & B)

With the Amp in Post as shown above, the parallel Paths A & B are fed into the input

of the Amp.* You can still move FX into either Path A or B, in which case they’ll be in

parallel, with each Path’s output individually controlled by the Mixer’s A & B Level and

Pan options to allow you to custom blend them before they hit the Amp.

*Note: All Amps & Preamps behave as “mono” Models, which impact the stereo output

of any FX Models positioned before them within the signal ﬂow. For more info, please see

“Model Types and Mono/Stereo Signal Routing” on page 3•5.

Selecting Amp, Cab & Mic Models

Press the VIEW button to display the Signal Flow View and use the Nav. Pad to select

Amp A or Amp B.

The Signal Flow View - Amp B selected

OnceanAmpModelisselected,you’llseethe4editableAmpoptionsatthebottomof

thescreen,accessibleviatheMulti-functionknobs1-4.

• Knob 1 - Selects the Amp or Preamp Model.

• Knob 2 - Selects the Cab Model.

Amp, Cab & Mic Models

6•4

• Knob 3 - Selects the Mic Model.

• Knob 4 - When the current Preset includes two Amp models, this selects which

Amp (the Amp within Path A or B) is controlled by the Amp Tone knobs.

As you change the Amp Model (Knob 1), you’ll also see that default Cab and Mic models

are automatically selected for each Amp or Preamp (see “About Default Amp Settings”

on page 6•5).ButyoucanuseKnobs3&4toselectanyCaband/orMicyoulike.These

settings are saved per Preset.

Attention Bass Players: Try the Flip Top Bass Amp Model for some thump! Note that this

Model loads with a matching 1x15 Flip Top speaker cab, as well as a full set of Mic Model

options for stellar bass tones. (And yes, you can indeed select any other Cab with the Flip

Top Bass Amp Model, or choose the Flip Top Cab with any Guitar Amp Model!) See the

following sections for details about these models.

Amp and Preamp Models

We’ve included a complete set of “Preamp” versions of each Amp as well. Choose one of

these to obtain the tone of just the preamp stage of the amp - recommended when feeding

your POD HD output into an external ampliﬁer.*

A Preamp Model is selected for Amp B

*Note that, whether an Amp or Preamp is selected, the additional application of Cab and

Mic Models is dependent upon the SETUP:OUTPUT settings. Please see “Page4,Setup:

Output Options” on page 2•7.

The overall volume levels among the different Preamp Models varies - this is normal. The

Preamp sections of each of the classic ampliﬁers we modeled are indeed quite different,

and we’ve set the Preamps’ default values to best match the type of power amp into which

they are intended to feed. Tweak the DRIVE and VOLUME knobs to optimize the level

for your speciﬁc needs!

Amp, Cab & Mic Models

6•5

Amp Block States

The Amp Blocks have 3 available states: On, Off (bypassed) or Disabled (sometimes

referred to as a “Null” state for the Block).

Amp Block “On” Amp Block “Off” Amp Block “Disabled” (Null Block)

About Default Amp Settings

Whenever you change to a different Amp or Preamp Model, predetermined Cab &

Mic models are automatically loaded, as well as Amp Tone Knob settings, designed to

complement the Amp type. As noted throughout this chapter, you can certainly switch to

a different Cab and/or Mic Model - just be sure to save your Preset to retain these changes.

Mic Models

TofollowisalistofallMicModels.NotethatallGuitarAmp’sCabsofferaselectionof8

Mics,andthe1x15FlipTopBassCaboffersitsownselectionof8MicModels.

Mic Model Descriptions

Mic Name Based On...*

Guitar Cab Mic Models

57 On Xs Shure® SM57 Dynamic, On Axis

57 Off Xs Shure® SM57 Dynamic, Off Axis

409 Dyn Sennheiser® MD 409 Dynamic

421 Dyn Sennheiser® MD 421 Dynamic

4038 Rbn Coles 4038 Ribbon

121 Rbn Royer® 121 Ribbon

67 Cond Neumann® U67 Condenser

87 Cond Neumann® U87 Condenser

* All product names used in this manual are trademarks of their respective owners, which are in no way associated or afﬁliated with Line 6. These trademarks of other manufacturers are used solely to identify the products of those manufacturers whose tones and sounds were

studied during Line 6’s sound model development. Shure® is a registered trademark of Shure Incorporated, Sennheiser® is a registered trademark of Sennheiser Electronic Corporation, Neumann® is a registered trademark of Georg Neumann GMBH, Royer® is a registered

trademark of Bulldog Audio, Inc. DBA Rover Labs

Amp, Cab & Mic Models

6•6

Mic Model Descriptions

Mic Name Based On...*

Bass Cab Mic Models

57 On Xs Shure® SM57 Dynamic, On Axis

421 Dyn Sennheiser® MD 421 Dynamic

12 Dyn AKG® D12

112 Dyn AKG® D112

20 Dyn EV® RE20

7 Dyn Shure® SM7B

40 Dyn Heil® PR40

47 Cond Neumann® U47

Editing Amp Parameters

To toggle the selected Amp model On or Off

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

Press the ENTER - AMP ON/OFF button once. Toggling the Amp “Off” results

in bypassing the Amp, Cab and Mic processing.

To adjust the Amp Tone

Turn any of the Amp Tone knobs to adjust the desired settings for the selected Amp.

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

SAVE

HOLD FOR SYSTEM & I/O

VIEW

The Amp Tone knobs

Whenever you adjust any of the Amp Tone knobs, you’ll see the “Momentary” AMP:

EDIT LCD screen temporarily displayed, showing the actual values of the Tone knobs for

both current Amp A & Amp B Models (depending on your Amp Knobs Display setting,

see “Page 1, Setup:Utilities Options” on page 2•2). Also see the next section for more

about the AMP: EDIT options.

trademark of Bulldog Audio, Inc. DBA Rover Labs

Amp, Cab & Mic Models

6•7

Amp & Cab Edit Display

Double-press the ENTER button to access the Amp & Cab Edit screens. You’ll see up to 5

pages of options here, allowing you to ﬁne-tune Amp, Cab and Mic settings.* All settings

in these screens are saved per Preset.

*Note: When the selected Amp Model is a “full” Amp Model, you will see ﬁve Amp Edit

pages, with pages 2 & 3 offering additional “deep-editing” power amp-related functions,

and pages 4 & 5 offering deep-edit Cab functions, as described below. When the selected

Amp Model is a Preamp, you will see only three Amp Edit pages, which offer the same

options as the Amp/Cab Edit pages 1, 4 and 5 described below. Use the Nav. Disc left &

right arrow buttons to access all available pages.

Amp Edit - Page 1

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

Page 1 of the Amp:Edit Screen - both Amps are On

• With both Amp Models On: You’ll see the screen’s respective controls update as

you adjust the Amp Tone knobs, as shown above. Note that the black “dots” around

each knob indicate its last-saved value. You can also still access the Amp, Cab &

MicModelandAmpA/BselectionsviatheMulti-functionKnobs1-4whilethis

screen is displayed.

Amp, Cab & Mic Models

6•8

Page 1 of the Amp:Edit Screen - Amp A Bypassed

• With an Amp Model Off: You’ll see only a VOL knob, as shown above for Amp A.

This is a separate parameter strictly for the Amp Model’s Bypass Volume. Use the

VOLUME knob on your device to adjust this, and its value is stored separately with

the Preset for whenever the Amp Block is Bypassed.

Note that the VOLUME knob does not control the level at all for a “Null” Amp Block.

• UsetheMulti-Functionknobs1-4toadjusttheoptionsatthebottomofthescreen:

• Knob 1: Select the desired Amp or Preamp Model.

• Knob 2:SelectthedesiredCabModel(alsoseethePage4options).

• Knob 3:SelectthedesiredMicModel(alsoseethePage4options).

• Knob 4: Choose between adjusting controls for Amp A or Amp B. (This option

is available on all AMP EDIT screens.)

Amp, Cab & Mic Models

6•9

Amp Edit - Page 2

Page 2 offers three options that affect the power amp characteristics of your Amp Model.

Page 2 of the Amp:Edit Screen (not displayed for Preamp Models)

• Knob 1: Use this Master Volume to adjust the amount of power amp distortion. This

parameter is highly interactive with all other power amp parameters - the lower the

Master is set, the less effect the other controls will have.

• Knob 2: Setting the Sag to minimum offers a “tighter” responsiveness, and turning

clockwise provides more “touch” dynamics & sustain.

• Knob 3: Controls how much heater hum & AC ripple interacts with your tone. At

the maximum setting things get really freaky.

Amp Edit - Page 3

Page 3 offers two more options that affect the power amp characteristics.

Page 3 of the Amp:Edit Screen (not displayed for Preamp Models)

Amp, Cab & Mic Models

6•10

• Knob 1: Changes the Bias of the power tubes. Set to minimum to achieve a very

“cold” Class AB biasing. At maximum the amp is operating in Class A.

• Knob 2: The Bias Excursion determines how the power amp tubes’ voicing reacts

when they are pushed hard. Set low for a tighter feel. Set high for more tube

compression. This parameter is highly reactive with the DRIVE & MASTER settings.

• Knob 3: Has no function on this page.

Amp Edit - Page 4

Here you’ll ﬁnd Microphone and Speaker Cabinet options.

Page 4 of the AMP:EDIT Screen (appears as Page 2 for Preamp Models)

NOTE: If you selected “No Cab” for your Cab Model, these Mic and Early Reﬂections

settings will perform no function since no Speaker, Mic or Early Reﬂections processing is

applied.

• Knob 1: Sets the amount of “early reﬂections.” Higher values add more reﬂective

room sound to your Amp tone.

• Knob 2: Applies low frequency attenuation - helpful to tighten up the low end of

your tone.

• Knob 3: Selects the Mic type (see the Mic Model table on page 6•5).

Note: If you select the 1x15 Flip Top Bass Cab Model, you’ll see a unique set of Mic Models

in this list, best suited for Bass.

Amp, Cab & Mic Models

6•11

Amp Edit - Page 5

Here you’ll ﬁnd even further “deep-editing” parameters for the Speaker Cab, allowing you

to surgically reﬁne the the feel and frequency response to your personal taste.

• Knob 1: Adjusts the overall level of the modeled speaker Resonance, which results

in a more “lively,” brighter response on higher settings. Increasing the Resonance

Level will cause the overall volume to increase as well.

• Knob 2: Adjusts the low frequency level of the modeled speaker resonance. Just as

the name implies, increasing the value on this knob adds more low end “Thump” to

the Cab tone.

• Knob 3: Adjusts the Decay time of the modeled speaker resonance. This control

provides the feel of a “tighter” speaker cone at lower values and a “looser” speaker

at higher values.

Note: The above three Cab parameters are interactive - As the Resonance Level is decreased

so are the effects of the Thump and Decay parameters. Thump and Decay are applied to

the modeled speaker resonance, therefore, if the Resonance Level is set to a minimum, the

effects of Thump and Decay parameters will not be audible.

Resonance Level, Thump, and Decay controls will only be audible when the POD is in

Studio/Direct output mode.

Press the HOME button, or double-press the ENTER button to exit the AMP:EDIT screen

when done. Be sure to save your Preset to retain customized Amp Model settings.

Amp/Preamp Models

To follow is a table showing the classic ampliﬁers upon which all our HD Amp/Preamp

Models are based.* For more details, please also check out the POD HD Model Gallery,

available from http://line6.com/support/manuals/.

POD HD Amp/Preamp Models

Amp/Preamp Model Based On...*

Amp Disabled When selected, no Amp Model is loaded

Blackface Double Normal ‘65 “Blackface” Fender® Twin Reverb®, Normal input channel

Blackface Double Vibrato ‘65 “Blackface” Fender® Twin Reverb®, Vibrato input channel

Hiway 100 Hiwatt® Custom 100

Super O ‘60s Supro® S6616

Gibtone 185 Gibson® EH-185

Tweed B-Man Normal ‘59 Fender® Tweed Bassman®, Normal input channel

Tweed B-Man Bright ‘59 Fender® Tweed Bassman®, Bright input channel

Blackface ‘Lux Normal Fender® “Blackface” Deluxe Reverb®, Normal input channel

Blackface ‘Lux Vibrato Fender® “Blackface” Deluxe Reverb®, Vibrato input channel

Divide 9/15 Divided By 13 9/15

PhD Motorway Dr. Z® Route 66

Class A-15 ‘61 “Fawn” Vox® AC-15

Class A-30 TB Vox® AC-30 “Top Boost”

Plexi Lead 100 Normal ‘59 Marshall® “Plexi” Super Lead 100, Normal input channel

Plexi Lead 100 Bright ‘59 Marshall® “Plexi” Super Lead 100, Bright input channel

Brit J-45 Normal ‘65 Marshall® JTM-45 MkII, Normal input channel

Brit J-45 Bright ‘65 Marshall® JTM-45 MkII, Bright input channel

Brit P-75 Normal Park 75, Normal input channel

Brit P-75 Bright Park 75, Bright input channel

Brit J-800 Marshall® JCM-800

Bomber Uber 2002 Bogner Uberschall

Treadplate Mesa/Boogie® Dual Rectiﬁer®

Angel F-Ball Engl® Fireball 100

Line 6 Elektrik A face-melting Line 6 original

Flip Top Ampeg® B-15NF Portaﬂex® bass guitar amp

* All product names are trademarks of their respective owners, which are in no way associated or afﬁliated with Line 6. These product names and descriptions are provided for the sole purpose of identifying the speciﬁc products that were studied during Line 6’s sound model

development. Fender®, Twin Reverb®, Bassman® and Deluxe Reverb® are registered trademarks of Fender Musical Instruments Corporation. Vox® is a registered trademark of Vox R&D Limited. Marshall® is a registered trademark of Marshall Ampliﬁcation Plc. Dr. Z®

is a registered trademark of Dr. Z Amps, Inc. Mesa/Boogie® and Dual Rectiﬁer® are registered trademarks of Mesa/Boogie, Ltd. Engl® is a registered trademark of Beate Ausﬂug and Edmund Engl. Hiwatt® is a registered trademark of Fernandes Company, Ltd. Fane® is a

trademark of Fane International. Gibson® is a registered trademark of Gibson Guitar Corp. Supro® is a registered trademark of Zinky Electronics.

Amp Control Labels

For some Amp Models, you’ll see slightly different labels for the Amp Tone knobs displayed

in the Amp:Edit screen. In the cases where the classic amps we’ve modeled include special

knob controls, we’ve emulated their behaviors accordingly. These are listed as follows...

• Super O: The actual Supro® only has a Drive and a Tone knob, so we mapped Tone

to the MID knob and invented Bass, Treble, and Presence controls:

Super O Amp:Edit screen

• Divide 9/15: The Divided by 13 amp offers two interactive channels. The DRIVE

knob controls the “clean” channel, and the BASS knob is being used as the Drive

knob for the “dirty” channel. The MID & TREBLE knobs behave like the amp’s

Tone & Cut knobs.

Divide 9/15 Amp:Edit screen

• Class A-15 & Class A-30TB: Following the Vox® design, we’ve labeled the MID

knob as “Cut” for these two Amp Models - turning the knob counter-clockwise

reduces the high-end frequencies.

Class A-15 & Class A-30TB Amp:Edit screen

development. Fender®, Deluxe Reverb®, Twin Reverb® and Bassman® are registered trademarks of Fender Musical Instruments Corporation. Hiwatt® is a registered trademark of Fernandes Company, Ltd. Supro® is a registered trademark of Zinky Electronics. Dr. Z®

is a registered trademark of Dr. Z Amps, Inc. Vox® is a registered trademark of Vox R&D Limited. Marshall® is a registered trademark of Marshall Ampliﬁcation Plc. Mesa/Boogie® and Dual Rectiﬁer® are registered trademarks of Mesa/Boogie, Ltd. Engl® is a registered

trademark of Beate Ausﬂug and Edmund Engl.

Cab Models

To follow is a table showing the classic speaker cabinets upon which our Cab Models are

based.*

POD HD Cab Models

Cab Model Based On...*

212 Blackface Double Fender® “Blackface” Twin Reverb® combo cabinet, 2x12 inch

Jensen® speakers

412 Hiway Hiwatt® cabinet, 4x12 inch Fane® 12287 50 watt speakers

6x9 Super O Supro® S6616 combo cabinet, one “6x9” size speaker

112 Field Coil Gibson® EH-185 combo cabinet, 1x12 Field Coil Speaker

410 Tweed ‘59 Fender® Tweed Bassman® combo cabinet, 4x10 inch Jensen®

alnico speakers

112 BF ‘Lux Fender® “Blackface” Deluxe Reverb® combo cabinet , one 12 inch

Oxford 12K5-6 speaker

112 Celest 12-H Divided By 13 9/15 combo cabinet, one 12 inch Celestion® G12H

Heritage (70th anniversary) speaker

212 PhD Ported Dr. Z®, Z Best cabinet, 2x12 inch Celestion® speakers (one G12H

Heritage and one Vintage 30)

112 Blue Bell ‘61 “Fawn” Vox® AC-15 combo cabinet, one 12 inch Celestion®

Alnico Blue speaker

212 Silver Bell Vox® AC-30 “Top Boost,” 2x12 inch Celestion® Alnico Silver Bell

speakers

412 Greenback 25 Marshall® cabinet, 4x12 inch Celestion® G12M “Greenback”

speakers

412 Blackback 30 Marshall® cabinet, 4x12 inch Celestion® Rola G12H30W

“Blackback” speakers

412 Brit T-75 Marshall® cabinet, 4x12 inch Celestion® G12T75 speakers

412 Uber Bogner Uberschall cabinet, 4x12 inch Celestion® speakers (2 x

G12T75 and 2 x Vintage 30 speakers)

412 Tread V-30 Mesa/Boogie® cabinet, 4x12 inch Celestion® Vintage 30 speakers

412 XXL V-30 Engl® Pro cabinet, 4x12 inch Celestion® Vintage 30 speakers

115 Flip Top Ampeg® Custom Design, CTS 15 inch speaker

trademark of Fane International. Gibson® is a registered trademark of Gibson Guitar Corp. Supro® is a registered trademark of Zinky Electronics. Celestion® is a registered trademark of Celestion International Ltd. Jensen® is a registered trademark of Jensen Loudspeakers

and Audiovox Corporation.

FX Models

7•1

FX mOdelS

POD® HD includes a plethora of amazing FX Models, primarily from the popular Line 6

M13 Stompbox Modeler! This chapter provides Reference Tables showing all POD HD

FX Models by category, as well as details on their parameters. FX Model parameters are all

accessible within the Edit Mode. Please see “FX Edit Mode” on page 5•1 for details on

Edit Mode features.

TIP: For more details about the POD HD FX Models, please also check out the POD HD

Model Gallery and M13 Advanced Guide documents, available from http://line6.com/

support/manuals/.

Dynamics Models

Dynamics FX Models - Parameter Reference Table

Model Parameters

Hard Gate Open Threshold Close Threshold Hold Decay --

Noise Gate Threshold Decay -- -- --

Tube Comp Threshold Level -- -- --

Red Comp Sustain Level -- -- --

Blue Comp Sustain Level -- -- --

Blue Comp Treb Sustain Level -- -- --

Vetta Comp Sensitivity Level -- -- --

Vetta Juice Amount Level -- -- --

Boost Comp Drive Bass Comp Treble Output

Common Parameters

The following parameters are common to most Dynamics FX Models.

• Threshold: For compressor FX, lower values result in greater compression, along

with an automatic makeup gain stage dependent upon the Threshold setting.

• Sustain: Some compressors include Sustain, which is much the same as a Threshold

control, but functions in reverse - higher settings add more compression and thus

more sustain and squishy goodness.

• Level: Adjusts the overall volume - higher settings typically offer an output boost.

FX Models

7•2

Distortion Models

Distortion Model - Parameter Reference Table

Model Parameters

Tube Drive Drive Bass Mid Treble Output

Screamer Drive Bass Tone Treble Output

Overdrive Drive Bass Mid Treble Output

Classic Dist Drive Bass Filter Treble Output

Heavy Dist Drive Bass Mid Treble Output

Color Drive Drive Bass Mid Treble Output

Buzz Saw Drive Bass Mid Treble Output

Facial Fuzz Drive Bass Mid Treble Output

Jumbo Fuzz Drive Bass Mid Treble Output

Fuzz Pi Drive Bass Mid Treble Output

Jet Fuzz Drive Fdbk Tone Speed Output

Line 6 Drive Drive Bass Mid Treble Output

Line 6 Distortion Drive Bass Mid Treble Output

Sub Octave Fuzz Drive Bass Sub Treble Output

Octave Fuzz Drive Bass Mid Treble Output

Common Parameters

The following parameters are common to most Distortion FX Models.

• Drive: Adjusts the amount of overdrive, distortion or fuzz.

• Bass: Adjusts Bass EQ level

• Mid: Adjusts the Midrange EQ level.

• Treble: Adjusts Treble EQ level.

• Output: Adjusts the overall volume level - higher settings offer an output boost.

FX Models

7•3

Modulation Models

Modulation Models - Parameter Reference Table

Model Parameters

Pattern Tremolo Speed Step 1 Step 2 Step 3 Step 4

Panner Speed Depth Shape VolSens Mix

Bias Tremolo Speed Level Shape VolSens Mix

Opto Tremolo Speed Level Shape VolSens Mix

Script Phase Speed -- -- -- --

Panned Phaser Speed Depth Pan Pan Spd Mix

Barberpole Phaser Speed -- Fdbk Mode Mix

Dual Phaser Speed Depth Fdbk LFO Shp Mix

U-Vibe Speed Depth Fdbk VolSens Mix

Phaser Speed Depth Fdbk Stages Mix

Pitch Vibrato Speed Depth Rise VolSens Mix

Dimension Sw1 Sw2 Sw3 Sw4 Mix

Analog Chorus Speed Depth Ch Vib Tone Mix

Tri Chorus Speed Depth Depth2 Depth3 Mix

Analog Flanger Speed Depth Fdbk Manual Mix

Jet Flanger Speed Depth Fdbk Manual Mix

AC Flanger Speed Width Regen Manual --

80A Flanger Speed Range Enhance Manual Even Odd

Frequency Shifter Freq Mode -- -- Mix

Ring Modulator Speed Depth Shape AM/FM Mix

Rotary Drum Speed Depth Tone Drive Mix

Rotary Drm/Hrn Speed Depth Horn Dep Drive Mix

FX Models

7•4

Common Parameters

The following parameters are common to most Modulation FX Models.

• Speed: Adjusts the modulation/oscillation/tremolo speed for the effect, with higher

settings providing faster rates. Note that the Speed can be adjusted to a Hz value or

Note Division:

• Choosing a Hz value provides a speciﬁc modulation speed in cycles per second.

• Choosing a Note Division value provides a time that is based on the current Tap

Tempo (see “Tap Tempo” on page 1•5).

• Depth: Adjusts the intensity of the modulation. Higher settings result in more

extreme pitch bending, wobble or throb, depending on the effect.

• Fdbk (Feedback): The amount of delayed signal that is fed back into the effect.

Higher settings can provide more dramatic textures.

• Mix: Sets the balance of the “Dry” and “Wet” signals. At 0% no effect is added to

your signal; at 100% you will hear the effected signal only. For Chorus, Flanger &

Phase FX, results are typically best with the Mix set between 0 to 50%. For Vibrato,

Tremolo and Rotary FX, try the Mix at 90 - 100%. Feel free to experiment!

Note that the Script Phase, Pattern Tremolo , AC Flanger & 80a Flanger do not offer a

Mix parameter. Their dry/wet balance is “ﬁxed” just like the classic pedals that inspired

them!

FX Models

7•5

Filter Models

Filter Models - Parameter Reference Table

Model Parameters

Voice Box Speed Start End Auto Mix

V-Tron Start End Speed Mode Mix

Q Filter Freq Q Gain Type Mix

Vocoder Mic Input -- Decay Mix

Seeker Speed Freq Q Steps Mix

Obi Wah Speed Freq Q Type Mix

Tron Up Freq Q Range Type Mix

Tron Down Freq Q Range Type Mix

Throbber Speed Freq Q Wave Mix

Slow Filter Freq Q Speed Mode Mix

Spin Cycle Speed Freq Q VolSens Mix

Comet Trails Speed Freq Q Gain Mix

Octisynth Speed Freq Q Depth Mix

Synth O Matic Freq Q Wave Pitch Mix

Attack Synth Freq Wave Speed Pitch Mix

Synth String Speed Freq Attack Pitch Mix

Growler Speed Freq Q Pitch Mix

Common Parameters

The following parameters are common to most Filter FX Models.

• Frequency: Selects the center frequency used by the effect.

• Q: Adjusts the frequency width of the ﬁlter in use.

• Speed: Adjusts the rate of the model’s modulation or oscillators, can be adjusted to

a Hz value or Note Division:

• Choosing a Hz value provides a speciﬁc modulation speed in cycles per second.

• Choosing a Note Division value provides a time that is based on the current Tap

Tempo (see “Tap Tempo” on page 1•5)

FX Models

7•6

• Mix: Sets the balance of the “Dry” and “Wet” signals. At 0% no effect is added to

your signal; at 100% you will hear the effected signal only. For most Filter FX, try the

100% setting to achieve the full weirdness factor.

Pitch Models

Pitch Models - Parameter Reference Table

Model Parameters

Bass Octaver Tone Normal Octave -- --

Pitch Glide Pitch -- -- -- Mix

Smart Harmony Key Shift Scale -- Mix

Pitch FX Model Parameters

Since these FX are a bit more complex, we’ve provided examples of each Pitch FX Model’s

Edit Mode screen and parameter descriptions.

Bass Octaver

• Tone: The overall tone of the effect.

• Normal: Controls the volume of the dry signal.

• Octave: Controls the volume of the processed, octave signal.

FX Models

7•7

Pitch Glide

This effect is best used by assigning a Line 6 FBV™ Pedal Controller to the Pitch parameter

to “wham” out some wild pitch-bending effects (see “Expression Pedal Assignment” on

page B•16). However, you can set a speciﬁed pitch to add a static harmony or octave

unison note that follows your playing.

• Pitch: Manually lets you select the Pitch of the note that is heard in unison with

your input signal.

• Mix: Controls the balance of wet & dry signals. Set to 100% if you wish to hear only

the pitched signal, or somewhere near 50% to hear both your input signal plus the

pitched signal.

Smart Harmony

Select a Scale, Key and Shift value and our DSP algorithms will do the rest, producing a

perfect harmony note along with your guitar riffs. The available parameters are:

FX Models

7•8

• Key: Select the Key you’ll be playing in.

• Shift: Determines the interval value for the desired harmony note.

• Scale: Select the Scale you’d like to use (see the following instructions and table).

• Mix: Sets the balance or your dry signal + harmony notes.

The Smart Harmony effect automatically detects your guitar’s single-note pitch and shifts

it to match a user-selected Key and Scale. A choice of Keys is provided - Consult the table

below to achieve other scalic modes.

• Choose your Key on the left, then your mode on the top.

• The cell where the two connect is the Key to choose to get to the mode you’d like.

For example, for C - Lydian, the Scale you want is G Major.

Mode

Key Ionian Dorian Phrygian Lydian Mixolydian Aeolian Locrian

AA Maj G Maj F Maj E Maj D Maj C Maj Bb Maj

BB Maj A Maj G Maj Gb Maj E Maj D Maj C Maj

CC Maj Bb Maj Ab Maj G Maj F Maj Eb Maj Db Maj

DD Maj C Maj Bb Maj A Maj G Maj F Maj Eb Maj

EE Maj D Maj C Maj B Maj A Maj G Maj F Maj

FF Maj Eb Maj Db Maj C Maj Bb Maj Ab Maj Gb Maj

GG Maj F Maj Eb Maj D Maj C Maj Bb Maj Ab Maj

Smart Harmony Model - Scale Reference Table

FX Models

7•9

Preamp+EQ Models

EQ Models - Parameter Reference Table

Model Parameters

Graphic EQ 80Hz 220Hz 480Hz 1.1kHz 2.2kHz

Parametric EQ Lows Highs Freq Q Gain

Studio EQ Low Freq Low Gain Hi Freq Hi Gain Gain

4 Band Shift EQ Low Low Mid Hi Mid Hi Shift

Mid Focus EQ Hi Pass Freq Hi Pass Q Low Pass Freq Low Pass Q Gain

Vintage Pre Gain Output Phase Hi Pass Filter Lo Pass Filter

Common Parameters

The following parameters are common to EQ Models.

• Frequency (as well as Low, Mid, High): Selects the center frequency or range for the

particular EQ Band. (The Graphic EQ model includes “ﬁxed” Bands where the gain

is adjustable for each.)

• Q: Adjusts the frequency width or shape of the frequency band ﬁlter.

• Gain: Adjust the output level of the particular Band. (The Gain parameters accessed

by Multi-function Knob #4 adjust the overall output level.)

Vintage Pre

This Model is a vintage-voiced, mono tube mic preamp based on* the Requisite® Y7

vintage Tube Mic Preamp, excellent for use with your Mic source input, Variax acoustic

guitar models, or even in conjunction with Bass or Guitar Amps, anywhere in the signal

path, to provide some nice tube warmth.

* Requisite® is a registered trademark of Requisite Audio Engineering.

FX Models

7•10

• Gain: Dial in the amount of input gain - higher levels will add some tube distortion.

• Output: Determines the ﬁnal output level, capable of a signiﬁcant signal boost.

• Phase: Choose 0 for normal, or 180 to reverse the phase. (It can sometimes be

necessary to reverse the phase of one mic’ed signal when combined with another, to

correct for a resulting “hollow,” out-of-phase sound.)

• HPF: A High Pass Filter to reduce bass frequencies. Increase this Hz value to choose

where the low frequency reduction begins.

• LPF: A Low Pass Filter to reduce treble frequencies. Decrease this KHz value to

choose where the high frequency reduction begins.

Delay Models

Delay Models - Parameter Reference Table

Model Parameters

Ping Pong Time Fdbk Offset Spread Mix

Dynamic Dly L Time L Fdbk R Time R Fdbk Mix

Stereo Delay Time Fdbk Thresh Ducking Mix

Digital Delay Time Fdbk Bass Treble Mix

Dig Dly W/Mod Time Fdbk ModSpd Depth Mix

Reverse Time Fdbk ModSpd Depth Mix

Lo Res Delay Time Fdbk Tone Res Mix

Tube Echo Time Fdbk Wow/Flt Drive Mix

Tube Echo Dry Time Fdbk Wow/Flt Drive Mix

Tape Echo Time Fdbk Bass Treble Mix

Tape Echo Dry Time Fdbk Bass Treble Mix

Sweep Echo Time Fdbk Swp Spd Swp Dep Mix

Sweep Echo Dry Time Fdbk Swp Spd Swp Dep Mix

Echo Platter Time Fdbk Wow/Flt Drive Mix

Echo Platter Dry Time Fdbk Wow/Flt Drive Mix

Analog W/Mod Time Fdbk ModSpd Depth Mix

Analog Echo Time Fdbk Bass Treble Mix

Auto-Volume Echo Time Fdbk ModDep Swell Mix

Multi-Head Time Fdbk Heads 1-2 Heads 3-4 Mix

FX Models

7•11

Common Parameters

The following parameters are common to most Delay FX Models.

• Time: Adjusts the delay/repeat time, with higher settings providing longer delays.

Time can be adjusted to a MS value or Note Division:

• Choosing a MS value provides a speciﬁc time in milliseconds.

• Choosing a Note Division value provides a time that is based on the current Tap

Tempo (see “Tap Tempo” on page 1•5).

• Fdbk (Feedback): Sets the number of delayed repeats.

• Depth: Some delays include modulation. These will typically include a Depth

parameter to adjust the intensity of the pitch modulation applied to the repeats.

• ModSpd: Control the speed of the pitch modulation.

• Mix: Sets the balance of the “Dry” and “Wet” signals. At 0% no effect is added to

your signal; at 100% you will hear the delayed signal only.

Reverb Models

Reverb Models - Parameter Reference Table

Model Parameters

Plate Decay PreDelay Tone Mix

Room Decay PreDelay Tone Mix

Chamber Decay PreDelay Tone Mix

Hall Decay PreDelay Tone Mix

Echo Decay PreDelay Tone Mix

Tile Decay PreDelay Tone Mix

Cave Decay PreDelay Tone Mix

Ducking Decay PreDelay Tone Mix

Octo Decay PreDelay Tone Mix

Spring Decay PreDelay Tone Mix

‘63 Spring Decay PreDelay Tone Mix

Particle Verb Dwell Condition Gain Mix

FX Models

7•12

Common Parameters

The following parameters are common to all Reverb Models, with the exception of the

Particle Verb Model, which we’ve described separately.

• Decay: Sets the length of time the reverb effect sustains.

• Predelay: Conﬁgures the time before the reverb effect is heard.

• Tone: Adjusts the overall Tone of the wet reverb signal. Higher settings provide a

brighter, more reﬂective reverb quality.

• Mix: Sets the balance of the dry & wet signals, from 0% (dry signal only) to 100%

(wet reverb signal only).

Particle Verb

A new kind of reverb effect which turns your chords into a lush modulated pad in STABLE

mode. CRITICAL mode is similar, but with a slight rise in pitch. In HAZARD mode, all

stops are removed. The parameters for this model differ from the other Reverbs:

• Dwell: Essentially a decay parameter, which adjusts the length of time the reverb

tail lasts.

• Condition: Choose between STABLE, CRITICAL and HAZARD here for some

different reverb experiences!

• Gain: Sets overall output level of the effect.

FX Models

7•13

Volume/Pan & Wah Models

The Volume/Pan and Wah sets of Models are primarily designed to be used with an

FBV Controller Pedal.* However, you can also assign the TWEAK Controller to any of

these FX models’ “Position” parameters and manually work the effect - see “Tweak Knob

Assignment” on page 3•6.

*When you add any Wah or Volume Model to your tone, the EXP 1 and EXP 2 Controllers

are automatically assigned! Please see “Expression Pedal Assignment” on page B•16 for

more information.

Volume/Pan Models - Parameter Reference Table

Model Parameter

Volume Volume Level

Pan Pan L-R Balance

Volume

Volume: Adjusts the signal level. 100% is unity gain. This parameter can be accessed via

the Multi-function knob at any time. With your TWEAK knob or FBV Pedal assigned to

control the Volume, you’ll see this Volume parameter visually adjust with the knob/pedal

as well.

FX Models

7•14

Pan

• Pan: Adjusts the signal balance sent to the left and right stereo channels. 0% sends

full left, 50% sends equally left & right, and 100% sends full right.

The audible effect heard when using the Pan can differ quite a bit depending on the

position in your signal chain and what types of FX follow it. Here are a few examples:

Before Path A & B split

Pan positioned before Path A & B split

When placed here, your guitar signal is panned left to Path A and right to Path B. This

can be a cool way to “blend” the sounds of two Amp models.

FX Models

7•15

After Path A & B Mixer

Pan positioned after Path A & B Mixer

In this position, the stereo left & right signals fed into the Pan is determined by your

Mixer Pan settings. The Pan effect then pans these signal to the left and right main

outputs. Obviously, you’ll only beneﬁt from using the Pan in this post-Mixer position

when utilizing both the left and right outputs from POD HD.

Placing a Mono Output FX Model after the Pan

Mono FX Model (EQ) positioned after Pan

Just as with all stereo FX Models, when a mono FX Model is placed after the Pan, the

Pan Model’s output will become “mono-ized, as described in “Model Types and Mono/

Stereo Signal Routing” on page 3•5. Therefore, you’ll typically want to avoid placing a

mono FX Model later within the same signal path as the Pan Model.

FX Models

7•16

Wah Models

Wah Models - Parameter Reference Table

Model Parameters

Fassel Position Mix

Conductor Position Mix

Throaty Position Mix

Colorful Position Mix

Vetta Wah Position Mix

Chrome Position Mix

Chrome Custom Position Mix

Weeper Position Mix

Common Parameters

Each Wah offers the following two parameters:

• Position: This controls the “sweep” of the Wah. Any Wah Model is best used with

this parameter assigned to an FBV pedal, however, you can also access this parameter

with the Multi-function Knob, or assigned to your TWEAK knob, such as to dial in

a “parked” Wah tone.

• Mix: Sets the balance of the “Dry” and “Wet” signals. At 0% no Wah effect is added

to your signal; at 100% you will hear the Wah-effected signal only. Try lowering the

Mix to less than 100% for a more subtle effect!

Using the Looper

8•1

lOOper mOde

The Looper in POD® HD offers you up to 48 seconds of mono recording time (in Half-

Speed Mode) or 24 seconds recording time (in Normal Mode), as well as the ability to

undo, record overdubs, playback Loops at half speed, in reverse, and more! Most Looper

functions are accessible from the buttons on your POD HD device. Or, connect a Line 6

FBV™ Foot Controller for full, hands-free Looping!

Footswitch assignments for the Looper vary among the supported Line 6 FBV Controller

models - please see “Appendix B: FBV Foot Controllers” on page B•1 for the full info.

Looper Controls & Performance View

Hold the POD HD Bank Down button to toggle the Looper Mode On/Off - The button

remains lit when Looper Mode is active. When in Looper Mode, the Bank Up and A, B, C

& D buttons then provide access to the Looper functions, as indicated by the gold-colored

labels below each button.

Looper Mode functions for POD HD buttons

Additionally, the Looper screen of the Performance View displays the behavior of all

Looper functions.* You can think of these as “this is what will happen when the respective

button is pressed” indicators. Press the VIEW button to show this screen whenever you

use the Looper. (Also see the Looper - Performance View options , “Page 1, Setup:Utilities

Options” on page 2•2.)

The Performance View, Looper screen

Using the Looper

8•2

*Note: The “Play Once” and “Pre/Post” Looper Block position options are not accessible

via POD HD buttons. Play Once is accessible only with FBV Controller devices. The

Looper Block is moveable like any FX Model Block within the Signal Flow View screen.

To follow are descriptions of the functions shown in the Looper screen.

UNDO - Use the Bank Up button to “undo” the last recorded overdub. You can

press this button while actively in Overdub-Record mode, Loop Playback mode,

or while stopped and only the last recorded overdub is erased. This function will

not erase the originally recorded Loop.

PLAY ONCE - Pressing the FBV footswitch plays your recorded Loop (including overdubs,

if you’ve recorded any) for one cycle. Cool for triggering a pre-recorded phrase on demand!

• While playback is active, the Play/Stop icon appears as “STOP,” to indicate

that it can be pressed to stop playback immediately.

PRE/POST - The Looper Block can be moved to either a “Pre” or “Post” position within

the Signal Flow View, which dictates whether Amp & FX processing is added to your

guitar signal during the recording of your Loop, or only for the Loop’s playback.

• PRE: Your guitar signal is recorded unprocessed (i.e. - the Loop is recorded “pre”

Amp & FX processing). When played back, the Loop audio is mixed with incoming

guitar to feed the current Preset’s Amp & FX processing. If you change Presets or

tone settings while set to PRE, you’ll hear them applied to your Loop playback.

• When the Looper is set to PRE, the Pre/Post icon appears as “POST,”

to indicate thatthe Looper Block can be moved to the “POST” position.

• POST: Your guitar signal is recorded processed (i.e. - the Loop is recorded “post”

Amp & FX processing). When played back, the Loop audio is mixed with incoming

guitar AFTER the guitar signal has been processed through the Amp and FX. This

provides the ability select a new Preset which is applied only on your guitar input,

while the Loop plays back with the original recorded Preset tone!

• When the Looper is set to POST, the Pre/Post icon appears as “PRE,”

to indicate that the Looper Block can be moved to the “PRE” position.

Using the Looper

8•3

Note: If you record your Loop in POST mode and then switch to PRE for Loop playback,

this results in the current Amp+FX to be applied to the Loop playback (where the Loop was

already recorded with Amp+FX applied). Be aware that this can cause the Loop playback

to be signiﬁcantly louder!

RECORD/OVERDUB - To record a Loop, press the RECORD (A) button and the Looper

will immediately start recording. The button will remain lit while recording is active.

You’ll see the Performance View display the following:

• The Record function shows “DUB IN.” Pressing the RECORD button will

immediately put you into Overdub-Record mode.

• If you press RECORD at this time, whatever you play will be recorded

on top of the original Loop recording, and you’ll see the Performance

View indicator show “DUB OUT.” Press the button again to stop the

overdub recording.

• The Play/Record function shows “STOP” to indicate that pressing the

PLAY/STOP button will stop playback & recording.

Note: Once you have a Loop recorded, you can layer an overdub on top of your current

Loop at any time. Simply play back the Loop and step on the REC/OVERDUB switch press

the RECORD button while the Loop is playing. Your new live guitar will be recorded on

top of your previously recorded Loop. You can repeat this step and layer as many overdubs

as you like!

If you press RECORD while Loop playback is stopped, this will always record a new Loop,

and any previously recording will be discarded.

Using the Looper

8•4

PLAY/STOP - Press the PLAY/STOP (B) button to toggle Play/Stop for your recorded

Loop. If you are actively recording a Loop, press this switch to stop recording and set your

Loop “out” point. Thebutton remains lit whenever playback is active.

• While playback is active, the Play/Stop icon appears as “STOP.”

1/2 SPEED - Press the 1/2 SPEED (C) button to toggle the 1/2 Speed feature On/Off. The

button remains lit whenever 1/2 Speed is active.

Note that you can use the 1/2 Speed option for recording as well as playback. Speciﬁc

behaviors apply to each - please see “1/2 Speed Operation” on page 8•6.

• When 1/2 Speed is active, the Speed icon appears as “FULL.”

• When 1/2 Speed is Off, the Speed icon appears as “1/2.”

REVERSE - Press the REVERSE (D) button to toggle the Reverse Play feature On/Off. All

Loop playback is backwards when on. The button remains lit whenever Reverse is active.

• When Reverse is active, the Reverse icon appears as “FWD.”

• When Reverse is Off, the Reverse icon appears as “REV.”

Using the Looper

8•5

Looper Settings

Press the VIEW button to display the Signal Flow View screen and select the Looper to

access several additional settings.

The Signal Flow View screen, Looper options

• Playback (Knob 1) - Use Multi-function Knob 1 to adjust the Looper playback

volume. You may ﬁnd it useful to turn this down a bit so that your live guitar can be

slightly louder.

• Overdub (Knob 2) - Use Multi-function Knob 2 to adjust the level at which all

Overdubs are recorded. This level does not affect the level of your original Loop

recording.

• Hi Cut (Knob 3) & Lo Cut (Knob 4) - Use Multi-function Knobs 3 & 4 to adjust

these EQ options, to reduce the treble and bass of your Loop playback. It can be

helpful to reduce these to optimize the “mix” of your Loop playback with your live

guitar. These controls reduce the High and Low frequencies more as you raise their

values.

Using the Looper

8•6

1/2 Speed Operation

The Looper utilizes both the 1/2 Speed and Full Speed options for recording and playback.

These options directly affect the maximum Loop recording time.

POD HD Looper Record Time

Full Speed 24 Seconds maximum

1/2 Speed 48 Seconds maximum

Speciﬁc behaviors apply, as follows:

• Full Speed: When set to Full Speed before recording, the Looper provides up to 24

seconds max. recording time.

• Playback of the recorded Loop at the Full Speed setting is heard just as recorded.

• If you change the setting to 1/2 Speed, your recorded Loop is played back at half

speed, as well as pitched one octave lower.

• 1/2 Speed: When set to 1/2 Speed before recording, the Looper provides up to 48

seconds maximum recording time.

• Playback of the recorded Loop at the 1/2 Speed setting is heard just as recorded.

• If you change the setting to Full Speed, your recorded Loop is played back at

double speed, as well as pitched one octave higher.

USB Audio

9•1

uSb audiO

In this chapter, we’ll cover the USB audio capabilities of POD® HD. With the installation

of the Line 6 USB audio driver, you can use POD HD as a high quality audio interface for

your Mac® or Windows® computer!

The Line 6 USB Audio Driver

Before you connect POD HD to your computer, it is recommended that you download

and install the free Line 6 POD HD Edit software. This installs the necessary Line 6 USB

Audio Driver, as well as the Line 6 Monkey update utility (also see “Appendix A: Line 6

Monkey” on page A•1). The latest POD HD Edit installer, as well as individual installers

for the Driver & Line 6 Monkey, are also always available from http://line6.com/software.

*NOTE: As of the POD HD USB Device Driver version 5.7.0, Mac OS® X 10.4 (Tiger®)

is no longer supported. To use the POD HD USB connection with a Mac® running OS®

X 10.4, you’ll need to download and install the earlier POD HD Driver version 5.1.2,

available from http:line6.com/software/.

The Line 6 Software Downloads site - selecting the POD HD Edit software

Once installation is complete, just connect your device directly to a USB 2.0 port on your

computer (not into a USB hub) and power on your POD HD. Note that POD HD requires

the use of a USB 2.0 port on your computer.

Also see the POD HD Edit Installer Guide and the POD HD Edit Pilot’s Handbook,

available from http://line6.com/support/manuals.

USB Audio

9•2

Audio Routing

When using the POD HD USB connection, the audio driver manages several tasks. The

driver feeds the processed guitar signal out the USB Record Send to your computer and

receives playback audio from the computer. It also grabs the processed guitar signal before

routing it to the Record Send, to provide a low latency monitor signal, and then mixes the

monitor signal with the playback audio and feeds this combined signal to your POD HD

analog outputs.

Mix of monitor signal + playback

audio fed to analog outputs

Playback audio

from computer

Record Send audio

to computer

USB audio routing provided by the Line 6 USB audio driver

The POD HD Record Send

As shown above, the Record Send is the virtual “pipeline” that carries your POD HD-

processed, 24-bit digital signal across the USB connection, making it available to your

audio software as an input signal for recording.

The Record Send appears as an available audio input/recording device within your audio

software. Simply select this Send as the input for your audio track and you’ll be able

to record your POD HD signal. The level of the signal fed to the Send is affected by

your POD HD controls: Mixer block Volume A & B, Amp Model Drive & Volume, FX

Model Gain controls, Volume Pedal, etc., (but not the Master Volume knob). For the best

recording quality, watch the input meters provided in your software and adjust your level

to be at least halfway up, but never “clipping.”

USB Audio

9•3

Note that the type of audio signal fed to the Record Sends is controlled by the Output

Mode setting found in the POD HD Setup:Outputs screen. For most USB recording

situations, you’ll likely want to set this to “Studio/Direct.” Please see “Page 4, Setup:

Output Options” on page 2•7 for more info.

The Line 6 Audio-MIDI Devices Panel

The Line 6 Audio-MIDI Devices utility is the place where you conﬁgure various audio

driver settings. The options in the Line 6 Audio-MIDI Devices dialog are slightly different

if you are on a Mac® versus a Windows® system. See the following descriptions that

match your setup: For Mac® see next section, or for Windows® see page 9•8.

Mac® - Line 6 Audio-MIDI Devices

Launch the Line 6 Audio-MIDI Devices utility from within the Mac®

System Preferences. This utility provides access to several driver options.

Line 6 Audio-MIDI Settings - Driver Options (Mac®)

The Line 6 Audio-MIDI Settings window - Driver page

USB Audio

9•4

1 Device Selector: Select your POD HD here. If you have more than one supported Line

6 audio device connected, each will be selectable in this list.

2 Driver Version: Displays the current device’s installed driver version number.

3 ESN: Displays the current device’s unique Electronic Serial Number.

4 Driver/Inputs & Recording Selector: Choose between displaying the two pages of the

Driver Options window. (Also see “Inputs & Recording Page” on page 9•5.)

5 Run Audio MIDI Setup: Mac® Core Audio interface driver settings are conﬁgured in

the Mac OS® X Audio MIDI Setup utility. This button launches this dialog for you (see

“Mac® - Line 6 Audio-MIDI Devices” on page 9•3).

6 Sample Rate Converter Active: You’ll see this indicator light up whenever the

device is operating at a sample rate other than its native 48kHz rate. In addition to 48kHz,

POD HD supports 44.1kHz, 88.2kHz and 96kHz rates by utilizing an internal sample rate

converter. Please check your speciﬁc software’s documentation for details on conﬁguring

its audio sample rate.

7 USB Audio Streaming Buffer: Adjusts the buffer size for the audio responsiveness of

the Input Monitoring signal. Basically, the default setting should be ﬁne for most systems,

but if getting audio dropouts or working with large CPU demands on your system, raise the

slider a notch or two to the right until it alleviates the problem.

USB Audio

9•5

Inputs & Recording Page

The Line 6 Audio-MIDI Settings window - Inputs & Recording page

8 Record Sends List: Displayed here are the Record Sends for the current Line 6 device

that will be available to your audio software. For POD HD you’ll see the one, stereo “1-2

Main Out” Record Send.

9 Hardware Monitor Level: This slider independently controls the volume of your

processed guitar tone output for monitoring (the signal fed to the device’s main outputs).

It does not affect the level of the signal fed to your computer via the Record Send. This

allows you to balance your guitar’s monitor level against the playback audio from your

computer, such as when recording in DAW software.

If using POD HD as the audio interface for recording into a DAW application, then

your DAW may also offer its own “software monitoring” function. You may want to

use the DAW’s software monitoring in some scenarios, such as if you want to hear your

guitar signal processed with plug-ins on the DAW track. When utilizing DAW software

monitoring, you’ll want to set this slider’s level to minimum to allow you to hear only the

DAW software monitoring signal.

USB Audio

9•6

Mac OS® X Audio MIDI Setup Utility

POD HD utilizes the Mac® Core Audio driver type, making it a compatible audio interface

for practically any Mac® audio/multimedia software. As with most Core Audio devices,

some settings are found in the Audio Devices page of the Mac® Audio MIDI Setup dialog.

The Audio MIDI Setup utility - Mac OS® X 10.5*

*Note: The Audio MIDI Setup utility window within Mac OS® X 10.6 and higher have

a slightly different layout, but offers the same options and functionality as described here.

A System Settings:

• The Default Input and Default Output options allow you to choose the audio

interface you want your Mac® audio applications to use by default. If you want this

to be your Line 6 device, select it here.

• The System Output option allows you to choose which audio interface the Mac®

System sounds are played through.

USB Audio

9•7

B Device Properties: Choose your POD HD device here to allow the Audio Input and

Audio Output options display its settings.

C Audio Input & Output Options: If you’ve selected your POD HD in the Device

Properties, these settings will all refer to your POD HD device:

• You’ll see the Input and Output selectors both disabled, showing Master Stream for

each. POD HD includes one stereo “xed” Input (Record Send 1-2) and one xed

stereo Output (Out 1-2).

• The Source options are also disabled for POD HD.

• The Format selectors show you the Sample Rate* and Bit Depth that POD HD is

operating at for recording. The Bit Depth for POD HD is ﬁxed at 24 bit.

*It is recommended that you do not use the Sample Rate selectors in this window to set the

sample rate when your audio software is running. Typically, your audio software will offer a

sample rate option within its own “Preferences” settings.

• The Input Volume Sliders offer level control for the Record Send signal fed to your

recording software. Note that the sliders offer 18dB of input gain at the highest

setting.

• The Output Volume Sliders offer stereo level control for your software’s audio

playback fed to POD HD.

USB Audio

9•8

Windows® - Line 6 Audio-MIDI Devices

The following settings are the same for Windows® XP, Windows Vista® or Windows® 7,

unless otherwise noted.

Launch the Line 6 Audio-MIDI Devices from within the Windows® Control Panel. On

Windows® systems, POD HD offers both a DirectSound and ASIO® recording driver

for maximum compatibility with audio & multimedia software applications. It is always

recommended that you select the ASIO® audio driver within your audio software, if

supported, since this offers higher performance. When prompted for ASIO® driver

settings, this dialog is where you will make them.

The Line 6 Audio MIDI Devices - Driver tab (Windows® XP)

1 Device Selector - Select your POD HD here. If you have more than one supported

Line 6 audio device connected, each will be selectable in this list.

2 Driver Version - Displays the current device’s installed driver version number.

USB Audio

9•9

3 ESN - Displays the current device’s unique Electronic Serial Number.

4 Driver/Inputs & Recording Selector - Choose between displaying the two tabs of the

Driver Options window. (Also see “Inputs & Recording Page” on page 9•12.)

5 Driver Operation (Windows® XP only) - These options are only applicable for when

an application utilizes the POD HD device via the Windows® DirectSound® driver. They

will be non-selectable when in use via the ASIO® driver.

• Driver operating at: Displays the actual Sample Rate & Bit Depth the driver is

operating at when in use by an audio application. If not in use, “inactive” is displayed.

• Default Sample Rate & Bit Depth: Use this option to set the default sample rate

& bit depth that (non-ASIO®) applications will use when using POD HD as the

audio interface.

• Lock Driver Format: When checked, this forces the DirectSound® driver to always

operate at the Sample Rate and Bit Depth settings entered in the two ﬁelds above (as

opposed to following the sample rate requested by a Windows® audio application).

USB Audio

9•10

5 Driver Operation (Windows Vista® & Windows® 7)

On Windows® Vista & Windows® 7 you will see a Sound Control Panel button - click

this to launch the Windows® Sound panel. Within the Sound panel’s Playback and

Recording tabs you can designate POD HD as the “Default” audio device if you want all

your Windows® multimedia programs to utilize it as their sound card device.

POD HD selected as the Default Playback Device

You can also click on the Properties button in the Sound dialog to access the default

format settings for the POD HD Sample Rate and Bit Depth when used with Windows®

multimedia applications. (Note that if you are using an audio application that is set to

utilize the ASIO® driver for your Line 6 device, then ASIO® communicates directly with

the device, and these “default format” settings do not apply.)

USB Audio

9•11

The Window Vista/7 Control Panel>Sounds>Properties - Advanced tab

6 ASIO® Driver Settings

• ASIO® Client: If you are running audio software that is using POD HD as its ASIO®

audio device, the name of the software will appear here.

• Buffer Size: The ASIO® buffer size in use, which will affect the “responsiveness”

and “latency” of the DAW software. The lower the setting, the faster the response,

but with the trade-off of higher processor usage and the risk of audio dropouts. Raise

the value if you are getting inconsistent playback or recording in the audio software.

256 is generally a good setting to start with.

• Bit Depth: The ASIO® bit depth in use. It is recommended to use 24-bit here.

7 Sample Rate Converter Active - You’ll see this indicator light up whenever the

device is operating at a sample rate other than its native 48kHz rate. In addition to 48kHz,

POD HD supports 44.1kHz, 88.2kHz and 96kHz rates by utilizing an internal sample rate

converter.

8 USB Audio Streaming Buffer - This slider adjusts the buffer size for the audio

responsiveness of the Input Monitoring signal. Basically, the default setting should be ﬁne

for most systems, but if getting audio dropouts or working with large CPU demands on

your system, raise the slider a notch or two to the right until it alleviates the problem.

USB Audio

9•12

Inputs & Recording Page

10 11

The Line 6 Audio MIDI Devices - Inputs & Recording tab

9 Record Sends List: Displayed here are the Record Sends for the current Line 6 device

that will be available to your audio software. For POD HD you’ll see the one, stereo “1-2

Main Out” Record Send.

10 Hardware Monitor Level: This slider independently controls the volume of your

processed Source Input tone output for monitoring (the signal fed to the device’s main

outputs). It does not affect the level of the signal fed to your computer via the Record

Send. This allows you to balance your guitar’s monitor level against the playback audio

from your computer, such as when recording in DAW software.

Your DAW software may also offer its own “software monitoring” function. You may want

to use the DAW’s software monitoring in some scenarios, such as if you want to hear your

guitar signal processed with plug-ins on the DAW track. When utilizing DAW software

monitoring, you’ll want to set this Hardware Monitor slider to minimum to allow you to

hear only the DAW software monitoring signal.

11 Record Send Level: This slider independently controls the level of the POD signal

fed to your computer via the Record Send. This directly affects the signal level that is

recorded into your DAW tracks. Note that you can also check the +18dB checkbox here

if you need to boost the signal fed to your DAW.

Appendix A: Line 6 Monkey

A•1

appendiX a: line 6 mOnkey

Line 6 Monkey™ is the free, intelligent updater software that can be used

to keep your POD® HD, Line 6 FBV™ MkII Controller, and related Line 6

products, up to date. Line 6 Monkey is installed on your Mac® or Windows®

computer along with the POD HD USB device drivers. If you have not yet

installed the USB device drivers, you’ll need to do so to utilize POD HD with

your computer - see “USB Audio” on page 9•1. It’s highly recommended to

run Line 6 Monkey periodically to check for the latest updates.

Launch Line 6 Monkey

Connect POD HD to your computer’s USB 2.0 port and power on your device. To launch

Line 6 Monkey:

• On Mac®, go to /Applications/Line 6/Line 6 Monkey.

• On Windows®, go to Start menu\Programs\Line 6\Tools\Line 6 Monkey.

The following instructions are the same on Mac® or Windows®, unless otherwise noted.

You’ll need to Login so that Line 6 Monkey can communicate with Line 6 and provide you

with exactly what you need. It’s just a few clicks, and it’s free! If you have not yet created

an account, click the New User button and you’ll be walked right through the steps.

If you have not already done so, you’ll be prompted to Register your connected Line 6

hardware. It’s a painless process really, so click that Register button now.

Appendix A : Line 6 Monkey

A•2

FBV MkII Users: If you are using a Line 6 FBV MkII Controller then it is recommended

to install any available updates for it as well. Just connect your FBV MkII directly to your

computer’s USB port and use Line 6 Monkey as described above.

Grab Those Updates

If you see any items where a newer version is available, then you should click on that item

and let the little Monkey fellow walk you through the installation steps.

Line 6 Monkey - Update screen for POD HD

As an example, the above screenshot shows Monkey has detected that a newer Firmware -

Flash Memory version is available than is currently installed in our device. In this scenario

you can select the Flash Memory item and click Update Selection. Be sure to read the

prompts carefully and Monkey will assist you in performing the update in minutes. It is

especially important not to disturb the devices’ controls and cable connections until the

update fully completes!

Appendix A: Line 6 Monkey

A•3

Flash Memory Updates and Presets

Flash Memory updates typically include a complete set of Factory Presets, which may be a

revised set that differs from the set of Presets stored in the memory of your device. You’ll

be prompted during the update whether to keep your current Presets. Selecting “No” will

result in your device’s Presets being permanently overwritten.

The prompt during a Flash Memory update to keep your current Presets

TIP! You can save the full set of your device’s Presets as a “Bundle” ﬁle to your computer in

one easy step using POD HD Edit - see “POD HD Edit Software” on page 1•6.

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

Once a Flash Memory update is complete, it is recommended that you power

on POD HD while holding down the Nav. Pad - left arrow button. This

performs a “reset” of all global settings to their factory defaults. This reset

also updates your device’s Set List titles with those included in the new

Flash Memory version (if they differ).

Appendix B: FBV Foot Controllers

B•1

appendiX b: Fbv FOOt cOntrOllerS

Want hands-free access to your POD® HD Presets, Amps, FX and parameters? By

connecting one of the supported Line 6 FBV™ Controller devices you’ll get just that!

Here we’ll cover the use and many beneﬁts of using an FBV Controller with POD HD.

FBV MkII & FBV Series Controllers

The Line 6 FBV Shortboard MkII Controller is the recommended FBV device to use with

POD HD - It is the latest model and offers easy access to vital POD HD functions.

The FBV Shortboard MkII Controller

It is also possible to use several other FBV Controller models with POD HD: FBV Express

MkII, FBV Longboard and FBV Shortboard. Additionally, the Line 6 EX1 Expression

Pedal can be used with FBV Shortboard MkII or FBV Shortboard to optionally add a

2nd Pedal controller. For more about these products, please visit http://line6.com/

footcontrollers/fbvshortboardmkii.html.

Are you up to date? If you are using a Line 6 FBV MkII Series Controller, you can connect

it directly to your computer’s USB port and then launch Line 6 Monkey to check for and

install the latest updates - see “Appendix A: Line 6 Monkey” on page A•1.

Appendix B: FBV Foot Controllers

B•2

Getting Connected

All FBV devices come with an “RJ-45” cable. Note that this cable is indeed

a standard “Category 5” computer network cable. So, in case you lost yours,

simply run down to any electronics or computer store and ask for a cable of

this type.

With POD HD powered Off, connect this cable between the FBV device’s TO AMP jack

and the POD HD FBV PEDAL jack. If you have an optional Expression Pedal, connect

it to the EXP. PEDAL jack on your FBV now. Then Power On POD HD - You’ll see your

FBV light up, and you’re ready for action!

NOTE: If you have not done so already, it is recommended that you calibrate the Pedal

for your FBV device. Please see the Pilot’s Handbook that came with your FBV device,

or you can download it, or the FBV Advanced Guide, from http://line6.com/support/

manuals/.

Setup Options for FBV

There are several Setup options that affect POD HD behaviors when an FBV device is

connected. Hold the VIEW button to enter Setup to access the following options. (Also

see “Accessing System Setup” on page 2•1 for info on other Setup options.)

Setup Page 1

• Footswitch Mode (Knob 1): Conﬁgures the function of your FBV A, B, C & D

footswitches. This setting is global. See “FX & Amp Block FS Assignment” on page

3•7 for info on how to conﬁgure these assignments per Preset.

Appendix B: FBV Foot Controllers

B•3

• ABCD: Toggles the current Bank’s Presets A through D.

• FS 5-8: Toggles the Amp or FX Block to which you have assigned FS5 through

FS8 On/Off.

Note that the Performance View screens offer handy visual references for the current

Preset’s ABCD and FS assignments - see next section.

• Looper FS Display (Knob 3): Determines how and when the Looper Mode screen

is displayed (see page 1•3, as well as the following “Performance View” section).

Setup Page 2

• FBV Express (Knob 4): This option should only be set to “On” speciﬁcally for an

FBV Express MkII model controller, to allow it to function correctly with POD HD.

Appendix B: FBV Foot Controllers

B•4

POD HD Performance View Screens

The Performance View screens offer visual references for the Presets and/or Amp & FX

Blocks that your FBV footswitches are assigned to control.

FX assignment for FS1-FS8ABCD assignment for FS5-FS8

Please reference the Footswitch Mapping table on the following pages for your speciﬁc

FBV model device to determine which FBV footswitches relate to each of the 8 footswitch

assignments. (We cover how to edit & create these footswitch assignments on page B•18.)

When POD HD is in Looper Mode, a 3rd variation of the Performance View screen

displays the Looper functions that are accessed by FBV footswitches. Also see “Looper

Controls & Performance View” on page 8•1.

The Performance View with Looper Mode active

Appendix B: FBV Foot Controllers

B•5

FBV Controller Devices - Footswitch & Pedal Mapping

Your FBV device’s Footswitches and Pedal(s) are already mapped to speciﬁc POD HD

functions. These mappings are slightly different for each FBV Controller type - Please

reference the following table that matches your speciﬁc FBV model. See the following

sections for more details on the POD HD functions listed in these tables.

FBV Shortboard MkII

FBV Shortboard MkII - Footswitch & Pedal Mappings

Footswitch

Label

POD HD

Function

FBV LCD Screen Footswitch

LED

Description

FUNCTION 1 Looper Mode

On/Off

No change Lit when

mode active

Toggles Looper Mode

On/Off

FUNCTION 2 Set List Select

Mode On/Off

Displays Set List

selection screen

Lit when

mode active

Toggles Set List Select

Mode On/Off

Bank Up

(Bank Mode)

Displays queued

Bank, ﬂashing

No change Queues next Bank

Set List Select

(Set List Mode)

Displays Set List

selection

No change Selects Set List

Bank Down

(Bank Mode)

Displays queued

Bank, ﬂashing

No change Queues previous Bank

Set List Select

(Set List Mode)

Displays Set List

selection

No change Selects Set List

STOMP

FS1 On/Off No change Lit when

Block active

Toggles the “FS1”

assigned Amp/FX

Block

MODULATION

FS2 On/Off No change Lit when

Block active

Toggles the “FS2”

assigned Amp/FX

Block

Appendix B: FBV Foot Controllers

B•6

FBV Shortboard MkII - Footswitch & Pedal Mappings

Footswitch

Label

POD HD

Function

FBV LCD Screen Footswitch

LED

Description

DELAY

FS3 On/Off No change Lit when

Block active

Toggles the “FS3”

assigned Amp/FX

Block

REVERB

FS4 On/Off No change Lit when

Block active

Toggles the “FS4”

assigned Amp/FX

Block

Selects Preset A

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset A of

current Bank

FS5 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS5”

assigned Amp/FX

Block

Selects Preset B

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset B of

current Bank

FS6 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS6”

assigned Amp/FX

Block

Selects Preset C

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset C of

current Bank

FS7 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS7”

assigned Amp/FX

Block

Selects Preset D

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset D of

current Bank

FS8 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS8”

assigned Amp/FX

Block

TA P

Sets Tap Tempo No Change Blinks at

tempo

Tap to set tempo rate

Tuner Mode On/

Off

Displays Tuner Blinks at

tempo

Hold to enter/exit

Tuner Mode

Pedal Toe

Switch

EXP 1/EXP 2

Pedal Mode

(When no Pedal

2 is connected)

No change EXP 1 =

WAH lit

EXP 2 =

VOL lit

Toggles to the on-

board Pedal between

EXP 1 and EXP 2

modes

Toe Switch No change No change Assignable as a

footswitch

Appendix B: FBV Foot Controllers

B•7

Looper Mode Footswitch Mappings

When POD HD is placed in Looper Mode, several FBV footswitches change their mappings

to perform the following Looper functions. Please also see “Looper Mode” on page 8•1.

FBV Shortboard MkII - Looper Mode Footswitch Mappings

Footswitch

Label

POD HD Looper

Function

Footswitch LED Description

FUNCTION 1 Looper Mode On/

Off

Lit when mode

active

Toggles Looper Mode On/Off

STOMP

Undo Lit brieﬂy, while

Undo action

occurs

Erases the most recent recorded

overdub

MODULATION Play Once Lit while playing

recorded loop

Plays the current recorded Loop

one time only

DELAY Looper Pre/Post Lit when Looper is

in Post position

Sets the position of the Looper

“Pre” or “Post” in the signal chain

Record/Overdub Lit when recording,

Flashes when

overdubbing

Immediately starts recording - Or, if

a loop is currently playing, overdubs

on top of the current loop

BPlay/Stop Lit when playing Toggles the recorded loop to play

and stop

Full/Half Speed Lit when half speed Toggles the loop playback and

recording between full and half

speed

DReverse/Forward Lit when selected Toggles loop playback and recording

between normal and reverse

Pedal Controllers

FBV Shortboard MkII devices include an “on-board” Expression Pedal, as well as an

optional jack to include a 2nd Expression Pedal. These pedals access the POD HD EXP 1

and EXP 2 assignable controllers. Please see “Expression Pedal Assignment” on page B•16

for how to assign these controllers to Amp & FX parameters to customize your Presets.

When no additional Pedal is connected to the FBV EXP. PEDAL input, the on-board

Pedal‘s “Toe Switch” will toggle between the control of EXP 1 and EXP 2. The red WAH

and green VOL LEDs on FBV illuminate to indicate the current Pedal Mode, respectively.

(It is also possible to manually assign other functions to the Toe Switch - see “Using the

EXP Pedal Toe Switch” on page B•20.)

Appendix B: FBV Foot Controllers

B•8

EXP 1 and EXP 2 with Pedal 2 Connected

Whena2ndExpressionPedal(suchasaLine6EX-1ExpressionPedal)isconnected,the

on-board Pedal remains mapped to only EXP 1, and Pedal 2 to only EXP 2. Whenever a

Pedal 2 is connected, you’ll see the EXP 1 & EXP 2 LEDs both lit.

FBV Express MkII

FBV Express MkII - Footswitch & Pedal Mappings

Footswitch

Label

POD HD

Function

7-Segment LED

Display

Footswitch

LED

Description

Selects Preset A

(ABCD Mode)

Displays “A” to

indicate selected

Preset

Lit when

selected

Loads Preset A of

current Bank

FS5 On/Off

(FS 5-8 Mode)

Displays current

Preset channel

Lit when

Block active

Toggles the “FS5”

assigned Amp/FX

Block

Selects Preset B

(ABCD Mode)

Displays “B” to

indicate selected

Preset

Lit when

selected

Loads Preset B of

current Bank

FS6 On/Off

(FS 5-8 Mode)

Displays current

Preset channel

Lit when

Block active

Toggles the “FS6”

assigned Amp/FX

Block

Selects Preset C

(ABCD Mode)

Displays “C” to

indicate selected

Preset

Lit when

selected

Loads Preset C of

current Bank

FS7 On/Off

(FS 5-8 Mode)

Displays current

Preset channel

Lit when

Block active

Toggles the “FS7”

assigned Amp/FX

Block

Appendix B: FBV Foot Controllers

B•9

FBV Express MkII - Footswitch & Pedal Mappings

Footswitch

Label

POD HD

Function

7-Segment LED

Display

Footswitch

LED

Description

Selects Preset D

(ABCD Mode)

Displays “D” to

indicate selected

Preset

Lit when

selected

Loads Preset D of

current Bank

FS8 On/Off

(FS 5-8 Mode)

Displays current

Preset channel

Lit when

Block active

Toggles the “FS8”

assigned Amp/FX

Block

Tempo

Indicator

Indicates current

Tempo rate

Dot ﬂashes at

Tempo rate

N/A This is an indicator

LED only

Pedal Toe

Switch

EXP 1/EXP 2

Pedal Mode

No change EXP 1 =

WAH lit

EXP 2 =

VOL lit

Toggles the Pedal

between EXP 1 and

EXP 2 modes

Toe Switch No change No change Assignable footswitch

Looper Mode Footswitch Mappings

When POD HD is placed in Looper Mode, the FBV footswitches change their mappings

to perform the following Looper functions. Please also see “Looper Mode” on page 8•1.

FBV Express MkII - Looper Mode Footswitch Mappings

Footswitch

Label

POD HD Looper

Function

Footswitch LED Description

Record/Overdub Lit when recording,

Flashes when

overdubbing

Immediately starts recording - Or, if

a loop is currently playing, overdubs

on top of the current loop

BPlay/Stop Lit when playing Toggles the recorded loop to play

and stop

Full/Half Speed Lit when half speed Toggles the loop playback and

recording between full and half

speed

DReverse/Forward Lit when selected Toggles loop playback and recording

between normal and reverse

Appendix B: FBV Foot Controllers

B•10

Pedal Controllers

FBV Express MkII devices include an “on-board” Pedal which provides access to both

the POD HD EXP 1 and EXP 2 assignable controllers. Please see “Expression Pedal

Assignment” on page B•16 for how to assign these controllers to Amp & FX parameters

to customize your Presets.

The Pedal‘s “Toe Switch” will toggle between the control of EXP 1 and EXP 2. The

red WAH and green VOL LEDs on FBV illuminate to indicate the current Pedal Mode,

respectively. (It is also possible to manually assign other functions to the Toe Switch - see

“Using the EXP Pedal Toe Switch” on page B•20.)

FBV Longboard

FBV Longboard - Footswitch & Pedal Mappings

Footswitch

Label

POD HD

Function

FBV LCD Screen Footswitch

LED

Description

FX LOOP Looper Mode

On/Off

No change Lit when

mode active

Toggles Looper Mode

On/Off

AMP 1 Set List Select

Mode On/Off

Displays Set List

selection screen

Lit when

mode active

Toggles Set List Select

Mode On/Off

REVERB

FS4 On/Off No change Lit when

Block active

Toggles the “FS4”

assigned Amp/FX

Block

TREMOLO

FS1 On/Off No change Lit when

Block active

Toggles the “FS1”

assigned Amp/FX

Block

MODULATION

FS2 On/Off No change Lit when

Block active

Toggles the “FS2”

assigned Amp/FX

Block

DELAY

FS3 On/Off No change Lit when

Block active

Toggles the “FS3”

assigned Amp/FX

Block

Appendix B: FBV Foot Controllers

B•11

FBV Longboard - Footswitch & Pedal Mappings

Footswitch

Label

POD HD

Function

FBV LCD Screen Footswitch

LED

Description

BANK DOWN

Bank Down

(Bank Mode)

Displays queued

Bank, ﬂashing

No change Queues previous Bank

Set List Select

(Set List Mode)

Displays Set List

selection

No change Selects Set List

BANK UP

Bank Up

(Bank Mode)

Displays queued

Bank, ﬂashing

No change Queues next Bank

Set List Select

(Set List Mode)

Displays Set List

selection

No change Selects Set List

CHANNEL A

Selects Preset A

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset A of

current Bank

FS5 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS5”

assigned Amp/FX

Block

CHANNEL B

Selects Preset B

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset B of

current Bank

FS6 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS6”

assigned Amp/FX

Block

CHANNEL C

Selects Preset C

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset C of

current Bank

FS7 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS7”

assigned Amp/FX

Block

CHANNEL D

Selects Preset D

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset D of

current Bank

FS8 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS8”

assigned Amp/FX

Block

TAP TEMPO

Sets Tap Tempo No Change Blinks at

tempo

Tap to set tempo rate

Tuner Mode On/

Off

Displays Tuner Blinks at

tempo

Hold to enter/exit

Tuner Mode

Pedal 1

Toe Switch

Toe Switch No change No change Assignable as a

footswitch

Appendix B: FBV Foot Controllers

B•12

Looper Mode Footswitch Mappings

When POD HD is placed in Looper Mode, several FBV footswitches change their mappings

to perform the following Looper functions. Please also see “Looper Mode” on page 8•1.

FBV Longboard - Looper Mode Footswitch Mappings

Footswitch

Label

POD HD Looper

Function

Footswitch LED Description

REVERB

Undo Lit brieﬂy, while

Undo action

occurs

Erases the most recent recorded

overdub

TREMOLO Play Once Lit while playing

recorded loop

Plays the current recorded Loop

one time only

MODULATION Looper Pre/Post Lit when Looper is

in Post position

Sets the position of the Looper

“Pre” or “Post” in the signal chain

CHANNEL A

Record/Overdub Lit when recording,

Flashes when

overdubbing

Immediately starts recording - Or, if

a loop is currently playing, overdubs

on top of the current loop

CHANNEL B Play/Stop Lit when playing Toggles the recorded loop to play

and stop

CHANNEL C

Full/Half Speed Lit when half speed Toggles the loop playback and

recording between full and half

speed

CHANNEL D Reverse/Forward Lit when selected Toggles loop playback and recording

between normal and reverse

Pedal Controllers

FBV Longboard devices include two “on-board” Pedals, PEDAL 1 and PEDAL 2. These

pedals are permanently mapped to the POD HD EXP 1 and EXP 2 assignable controllers,

respectively. Please see “Expression Pedal Assignment” on page B•16 for how to assign

these controllers to Amp & FX parameters to customize your Presets.

ItispossibletomanuallyassignthePEDAL1ToeSwitchtotoggleAmporFXBlocksOn/

Off - see “Using the EXP Pedal Toe Switch” on page B•20.

Appendix B: FBV Foot Controllers

B•13

FBV Shortboard

FBV Shortboard - Footswitch & Pedal Mappings

Footswitch

Label

POD HD

Function

FBV LCD Screen Footswitch

LED

Description

FX LOOP Looper Mode

On/Off

No change Lit when

mode active

Toggles Looper Mode

On/Off

BANK

Bank Up

(Bank Mode)

Displays queued

Bank, ﬂashing

No change Queues next Bank

BANK Bank Down

(Bank Mode)

Displays queued

Bank, ﬂashing

No change Queues previous Bank

STOMP

FS1 On/Off No change Lit when

Block active

Toggles the “FS1”

assigned Amp/FX

Block

MODULATION

FS2 On/Off No change Lit when

Block active

Toggles the “FS2”

assigned Amp/FX

Block

DELAY

FS3 On/Off No change Lit when

Block active

Toggles the “FS3”

assigned Amp/FX

Block

REVERB

FS4 On/Off No change Lit when

Block active

Toggles the “FS4”

assigned Amp/FX

Block

CHANNEL A

Selects Preset A

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset A of

current Bank

FS5 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS5”

assigned Amp/FX

Block

Appendix B: FBV Foot Controllers

B•14

FBV Shortboard - Footswitch & Pedal Mappings

Footswitch

Label

POD HD

Function

FBV LCD Screen Footswitch

LED

Description

CHANNEL B

Selects Preset B

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset B of

current Bank

FS6 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS6”

assigned Amp/FX

Block

CHANNEL C

Selects Preset C

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset C of

current Bank

FS7 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS7”

assigned Amp/FX

Block

CHANNEL D

Selects Preset D

(ABCD Mode)

Displays current

Preset name

Lit when

selected

Loads Preset D of

current Bank

FS8 On/Off

(FS 5-8 Mode)

Displays current

Preset name

Lit when

Block active

Toggles the “FS8”

assigned Amp/FX

Block

TA P

Sets Tap Tempo No Change Blinks at

tempo

Tap to set tempo rate

Tuner Mode On/

Off

Displays Tuner Blinks at

tempo

Hold to enter/exit

Tuner Mode

Pedal Toe

Switch

EXP 1/EXP 2

Pedal Mode

(When no Pedal

2 is connected)

No change EXP 1 =

WAH lit

EXP 2 =

VOL lit

Toggles to the on-

board Pedal between

EXP 1 and EXP 2

modes

Toe Switch No change No change Assignable as a

footswitch

Appendix B: FBV Foot Controllers

B•15

Looper Mode Footswitch Mappings

When POD HD is placed in Looper Mode, several FBV footswitches change their mappings

to perform the following Looper functions. Please also see “Looper Mode” on page 8•1.

FBV Shortboard - Looper Mode Footswitch Mappings

Footswitch

Label

POD HD Looper

Function

Footswitch LED Description

FX LOOP Looper Mode On/

Off

Lit when mode

active

Toggles Looper Mode On/Off

STOMP

Undo Lit brieﬂy, while

Undo action

occurs

Erases the most recent recorded

overdub

MODULATION Play Once Lit while playing

recorded loop

Plays the current recorded Loop

one time only

DELAY Looper Pre/Post Lit when Looper is

in Post position

Sets the position of the Looper

“Pre” or “Post” in the signal chain

CHANNEL A

Record/Overdub Lit when recording,

Flashes when

overdubbing

Immediately starts recording - Or, if

a loop is currently playing, overdubs

on top of the current loop

CHANNEL B Play/Stop Lit when playing Toggles the recorded loop to play

and stop

CHANNEL C

Full/Half Speed Lit when half speed Toggles the loop playback and

recording between full and half

speed

CHANNEL D Reverse/Forward Lit when selected Toggles loop playback and recording

between normal and reverse

Pedal Controllers

FBV Shortboard devices include an “on-board” Pedal, as well as an optional jack on the

back to include a 2nd Expression Pedal. These pedals access the POD HD EXP 1 and EXP

2 assignable controllers. Please see “Expression Pedal Assignment” on page B•16 for how

to assign these controllers to Amp & FX parameters to customize your Presets.

When no additional Pedal is connected to the FBV EXP. PEDAL input, the on-board

Pedal‘s “Toe Switch” will toggle between the control of EXP 1 and EXP 2. The red WAH

and green VOL LEDs on FBV illuminate to indicate the current Pedal Mode, respectively.

(It is also possible to manually assign other functions to the Toe Switch - see “Using the

EXP Pedal Toe Switch” on page B•20.)

Appendix B: FBV Foot Controllers

B•16

EXP 1 and EXP 2 with Pedal 2 Connected

Whena2ndExpressionPedal(suchasaLine6EX-1ExpressionPedal)isconnectedto

FBV Shortboard, the on-board Pedal remains mapped to only EXP 1, and Pedal 2 to only

EXP 2. Whenever a Pedal 2 is connected, you’ll see the EXP 1 & EXP 2 LEDs both lit.

Expression Pedal Assignment

As shown in the preceding tables, FBV devices’ Pedals are designed to access the POD HD

EXP 1 and EXP 2 controllers, which can be assigned to virtually any Amp or FX Model

parameter. To follow are the steps to assign these controllers to POD HD parameters.

Controlling Amp & FX Parameters

Conﬁguring the EXP 1 & EXP 2 assignments is done within the Controller Assign screen.

These settings are all saved per Preset. From the Signal Flow View screen, select the Amp

or FX Block for which you’d like to create a Pedal assignment, then double-press the

MOVE button. For our example, we’ll select our Delay FX block in the Signal Flow View:

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

Note: When a Controller is assigned to any FX Model parameter, manually editing this

parameter’s value will result in changing the Controller’s MIN or MAX value. For example,

if the EXP-1 Pedal Controller is assigned to a Wah FX Model’s Position parameter, select

the Wah Model, go to its Edit View screen, and select the Position parameter. If you turn

multifunction knob #4 when the Pedal is near the “heel” position, the MIN value is

adjusted. If you turn the knob when the Pedal is near the “Toe” position, the MAX value

is adjusted.

Appendix B: FBV Foot Controllers

B•17

The Controller Assign screen is then displayed speciﬁcally for the selected Model. In our

example, it is the Digital Delay W/Modulation. Use the Multi-function Knobs 1-4 to

conﬁgure the Pedal assignment options.

The Controller Assign screen

• Parameter (Knob 1): Select the parameter for the current Model that you want to

control.* For our example, we’ll choose the Mix parameter.

• Controller (Knob 2): Select the Pedal Mode that you want to assign to the parameter.

Choose Off to have no Pedal assignment, or choose EXP 1 or EXP 2. (Note that you

can alternatively choose TWEAK here to have the parameter assigned to your POD

HD TWEAK knob, instead of an FBV Pedal!)

• Min. Value (Knob 3): Set the desired parameter value for the Pedal’s “heel” position.

• Max. Value (Knob 4): Set the parameter value you’d like for the Pedal’s “toe” position.

* Note that when you add a Wah FX Model to your tone, the “Position” parameter for the

Wah is automatically assigned to EXP 1. Likewise, when adding a Volume or Pan FX Model,

its Position parameter is automatically assigned to EXP 2. This will result in multiple items

assigned to these EXP Pedals if you already have existing Pedal assignments. For all Factory

Presets that already include a Wah, Volume or Pan, these are typically already assigned as

well. Be sure to remove any unwanted Model’s EXP assignment for your Preset.

Appendix B: FBV Foot Controllers

B•18

Amp & FX Block Footswitch Assignment

FBV footswitches, as well as the on-board Pedal’s “Toe Switch,” can be conﬁgured to

toggle any of the Amp or FX Blocks On/Off. You can reference the current Preset’s FX

footswitch assignments within the Performance View screen, as covered on page B•4.

These settings are saved per Preset.

Assigning an FX or Amp Block to a Footswitch

From the Signal Flow View, select the FX or Amp Block that you want assigned to one of

your footswitches. As an example, we’ll select the Delay FX Block. Then Press and hold

the ENTER button to display the Footswitch Assign screen.

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

Select the desired Amp or FX block, then press and hold the ENTER button

The Footswitch Assign screen, with a Delay FX Model selected

Appendix B: FBV Foot Controllers

B•19

Use Multi-function Knob 1 to select the footswitch to which you want this FX Block

assigned - choose FS1 through FS8, the EXP Toe Switch, or None to remove the Block’s

assignment. The following behaviors apply:

• If a footswitch already has an Amp or FX Block assigned: The existing Block remains

assigned, and selecting this footswitch additionally assigns your new Block. When

referencing the Performance View, you’ll see the footswitch display a “Multi” graphic

to indicate this. You can conﬁgure 2 or more parameters to the same footswitch to

toggle them On/Off simultaneously - or, have one toggle On while another Toggles

Off!

Indicates multiple Blocks assigned to a footswitch

TIP: To reference current footswitch assignments, when in the Footswitch Assign screen,

use the Nav. Pad buttons to select each Block, and look at the Knob 1 setting for each

at the bottom of the screen.

• When a footswitch has no Block assigned: You’ll see the N/A graphic displayed in

the Performance View for the respective footswitch.

Indicates no Blocks assigned to the footswitch

Appendix B: FBV Foot Controllers

B•20

Using the EXP Pedal Toe Switch

As noted above, when adding a Wah or Volume/Pan Model to your tone, their Position

parameters are automatically assigned to the EXP 1 and EXP 2 controllers. Most Factory

Presets already include this Wah/Volume switching pre-conﬁgured for you. But the Toe

Switch assignment is not set automatically for newly added Amp or FX Models, so here is

how to set this up manually.

• With the Wah Model selected, go to the FS Assign screen and assign its FX Block to

the EXP TOE SWITCH, following the instructions above. This allows the Wah to

be toggled On/Off via the pedal Toe Switch.

Assigning an FX Block to the on-board pedal’s “Toe Switch”

Further, if you have a different FX parameter (such as the Volume - Position) being

controlled by the opposite EXP Pedal Mode, you’ll likely ﬁnd it useful to have the Toe

Switch toggle both these FX Blocks On/Off alternately, so that only the desired Model

is active while being controlled. For example, say you have a Preset where the Wah is

controlled by EXP 1, and the Volume by EXP 2:

Note: If you have a “Pedal 2” connected to your FBV (or if using an FBV Longboard) you

may not want to use the following conﬁguration, since the Wah and Volume are already

controlled by your two Pedals individually.

• Click the EXP TOE SWITCH switch so that the red EXP 1 LED is lit.

• In the Signal Flow View, select the Volume FX block and toggle it “Off” using the

ENTER button. You should now see the Wah “On” and the Volume “Off.”

Appendix B: FBV Foot Controllers

B•21

Wah in “On” Volume is “Off”

• Repeat the previous Footswitch Assign steps for both the Wah and the Volume,

assigning each to the EXP TOE SWITCH.

• Now whenever you click the EXP TOE SWITCH to EXP 1 for this Preset, the

Volume is switched “Off” and the Wah is switch “On” and is controlled by the Pedal

- and vice versa when switching to EXP 2.

• Be sure to save to retain these settings with your Preset!

Set List Select

For FBV Shortboard MKII & FBV Longboard devices, you can access the Set Lists screen

and load a different Preset (also see page 4•1). To do this from your FBV:

• Press FUNCTION 2 (Shortboard MkII) or AMP 1 (Longboard) and you’ll see the

Set Lists screen displayed on your POD HD.

The Set Lists screen

• Press the BANK UP and BANK DOWN footswitches to select the desired Set List.

Note that your FBV LCD screen displays the name of the selected Set List.

• Press FUNCTION 2 / AMP 1 once again to load the selected Set List. You’ll see that

the same numbered Preset from the previous Set List is automatically loaded from

the new Set List.

Appendix B: FBV Foot Controllers

B•22

Tap Tempo

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

SAVE

HOLD FOR SYSTEM & I/O

VIEW

For all FBV devices, you can stomp rhythmically on the TA P footswitch to set your

Tap Tempo. Alternatively, you can set a numerical Tempo value within Setup (see

“Page 6, Tempo Options” on page 2•10).

You’ll see the LED on the TA P switch blink to indicate your current Tap Tempo BPM.

Tempo-based FX (Modulation, Filter & Delay FX) that offer a Tempo Sync parameter can

optionally be set to a note division of this Tap Tempo value.

Tuner Mode

For all FBV devices, to enter Tuner mode, press and hold the TA P button. See “Tuner

Mode” on page 1•4 for details.

ENTER

DBL PRESS TO ASSIGN CTL

MOVE

AMP & FX ON / OFF

SAVE

HOLD FOR SYSTEM & I/O

VIEW

The Tuner screen

Appendix B: FBV Foot Controllers

B•23

Line 6 Pod Hd Desktop Owners Manual POD® Advanced Guide (v2.0, Rev. A)

Navigation menu

Versions of this User Manual:

Views

Navigation