Linear Ccm Re1 Color Camera Quick Start Guide 231659A

: Linear Linear-Ccm-Re1-Color-Camera-Quick-Start-Guide linear-ccm-re1-color-camera-quick-start-guide linear pdf

Open the PDF directly: View PDF .
Page Count: 1

Copyright © 2011 Linear Corporation 231659 A

2. REMOVE FACTORY INSTALLED FOAM & EXISTING LENS 3. REPLACE EXISTING LENS FROM CASE 4. MOUNT CAMERA & CONNECT LIGHTING POWER

CCM-RE1

Color

CCTV Camera Kit

Installation

Instructions

PRODUCT DESCRIPTION

Linear’s Model CCM-RE1 (P/N ACP00886C) CCTV Color Camera Kit can be installed inside

the RE-1 Entry System. The camera provides a video signal for viewing the area in front of the

entry system.

The CCTV Color Camera Kit requires the Front Window Lens Model # NDLENS-RE1.

The camera is continuously powered by the RE-1. The camera’s infrared light emitters illuminate

the area directly on front of the entry system for nighttime or low light operation.

The camera focus has been factory adjusted to a range of three to four feet.

The RE-1 CAMERA jack is used to connect the camera to the main circuit board with the single-

ended modular cable supplied with the camera. This cable routes power to and video from the

camera.

The RE-1 VIDEO jack is the connection for a video cable with a Type “BNC” connector. Cable runs

of up to 300 feet of 75-ohm RG-59 video cable are acceptable. Longer cable runs may require

the use of a video amplifi er.

NOTE 1: Installations on existing systems must have the power disabled prior to removing the circuit

board.

NOTE 2: The Color Camera will ONLY work with RE-1’s front window lens model number NDLENS-RE1.

THIS NEW LENS HAS FOAM ON THE BACKSIDE. For installing the color camera for new or retrofi t

installations, make sure that ONLY the NDLENS-RE1 is used. Remove the foam ONLY when installing

the color camera.

1. REMOVE BACK COVER & CIRCUIT BOARD

5. REPLACE CIRCUIT BOARD & BACK COVER 6. CONNECT CAMERA CABLE AND VIDEO CABLE LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for

twenty four (24) months. This warranty extends only to wholesale customers who buy

direct from Linear or through Linear’s normal distribution channels. Linear does

not warrant this product to consumers. Consumers should inquire from their selling

dealer as to the nature of the dealer’s warranty, if any. There are no obligations

or liabilities on the part of Linear LLC for consequential damages arising out of or in

connection with use or performance of this product or other indirect damages with respect

to loss of property, revenue, or profi t, or cost of removal, installation, or reinstallation. All

implied warranties, including implied warranties for merchantability and implied

warranties for fi tness, are valid only until the warranty expires. This Linear LLC

Warranty is in lieu of all other warranties express or implied.

All products returned for warranty service require a Return Product Authorization

Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an

RPA# and other important details.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,CCM-RE1 - LINEAR P/N: 231659 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” x 8.500” - SCALE: 1-1 - PAGE 1 OF 1

(760) 438-7000

USA & Canada (800) 421-1587 & (800) 392-0123

Toll Free FAX (800) 468-1340

www.linearcorp.com

REMOVE

CIRCUIT

BOARD

DISCONNECT THESE

2 CONNECTORS

REMOVE THESE

4 SCREWS

REMOVE THE FRONT WINDOW LENS AND REPLACE

WITH THE NDLENS-RE1 LENS

SECURE THE NDLENS-RE1 LENS WITH THESE

2 SCREWS

SECURE THE CAMERA WITH THESE

2 SCREWS

INSERT THE WIRING HARNESS PLUG INTO

THE 2-PIN LIGHTING CONNECTOR

PLUG THE CAMERA CABLE

FROM THE CAMERA’S JACK

INTO THE RE-1’S CAMERA JACK

CONNECT THE MONITOR VIDEO

CABLE INTO THE RE-1’S VIDEO

OUTPUT CONNECTOR

IF FACTORY FOAM IS INSTALLED, REMOVE THE

FOAM AND GO TO STEP 4

IF FACTORY FOAM IS NOT INSTALLED, REMOVE

THESE 2 SCREWS FROM BEHIND THE FRONT

WINDOW LENS AND GO TO STEP 3

REPLACE

CIRCUIT

BOARD

RECONNECT THESE

2 CONNECTORS

SECURE WITH

4 SCREWS

IMPORTANT!

TO PREVENT INTERNAL INFRARED

LIGHT FROM ENTERING THE

CAMERA, BE SURE THE FOAM

GASKET AROUND THE CAMERA’S

LEN’S PRESSES FIRMLY AGAINST

THE RE-1’s FRONT WINDOW LENS