Linear Dr 1 Channel Receiver Quick Start Guide Ventura 200108E.CHP

: Linear Linear-Dr-1-Channel-Receiver-Quick-Start-Guide linear-dr-1-channel-receiver-quick-start-guide linear pdf

Open the PDF directly: View PDF .
Page Count: 1

Download
Open PDF In Browser	View PDF

DESCRIPTION

DELTA-3
SYSTEM

The Delta-3 digital receiver and transmitter is a single-channel wireless radio
control designed for use with automatic garage/gate operators and access
control systems. All Delta-3 products (on the same frequency) can be mixed
and matched to suit your individual needs.
The Delta-3 radio format provides 256 different digital codes. The codes are
set using the 8-position coding switches in the units.

Single-channel Digital
Receiver and
Transmitter

In order to avoid the possibility of duplicating codes in adjacent systems,
factory set codes should not be used. In addition, among the valid codes
available, four others should not be used. These include: all keys set ON or
OFF and keys set alternating ON/OFF.
Where a number of receivers are to be installed in close proximity (as in an
apartment complex), install receivers at least 5 feet apart. If receivers are
installed closer than 5 feet apart, blocking may occur.
After completing an installation, operate the transmitter outside the building and
check to see that the coded signal being used does not interfere with neighboring
garage door operators and/or security systems. If interference is detected, select
another code and check coded signal again. Repeat if necessary.

Step 2 Code Transmitter and Receiver. Use a paper clip or
other pointed object (except a pencil or pen) to pick any
combination of ON/OFF codes and set them on switch keys 1
through 8 on the receiver and transmitter. The ON position is when
the top of the switch is down. The OFF position is when the top of
the switch is up and the bottom is down.

INSTR,CODE SET,DELTA-3
Linear P/N: 200108 E
Size: 8.500" x 11.000"
Material: 20 Lb. Mead Bond
Ink: Black
Scale: 1-1

RECEIVER
CODING SWITCH

recoded prior to operation.

(800) 421-1587 • www.linearcorp.com

SET
1-8

REMOVE
BATTERY
DOOR

☞ Caution: All transmitters and receivers should be

Code Setting and
Installation Instructions

DELTA-3 RECEIVER

Step 1 Locate Coding Switches. Locate the digital coding switch
for the receiver which is recessed in the center of the back of the case.
The transmitter coding switch is accessed by removing the battery
access door located on the back of the transmitter case. The keys
are numbered 1 through 8. The switches in the receiver must match
the switches in all transmitters used to operate the receiver.

24
V
RE
LA
Y
RA
PW DIO
R

TRANSMITTER
CODING SWITCH

Step 3A Connecting Receiver (using transformer power).

Step 3B Connecting receiver (using operator power).

Where it is not feasible to obtain power from the operator, connect
a Model 524 transformer (accessory) to the receiver as shown below.
Then plug the transformer into a convenient (unswitched) 110 VAC
outlet.

Connect the receiver to the garage door or gate operator as shown
in the diagram. Power will be supplied from the operator.

DELTA-3 TRANSMITTER
MATCH
1-8

3
2 24 VAC
1 RELAY
COM

3
2 24 VAC
1 RELAY
COM

3-TERMINAL
OPERATOR
2-TERMINAL
OPERATOR

(3) 24 VAC
(2) RELAY

(2) RELAY
(1) COM

SWITCHES 1, 3, 4, 7 & 8
ARE "ON" 2, 5 & 6 ARE "OFF"

ALL TRANSMITTER SWITCHES
MUST MATCH RECEIVER SWITCHES

Step 4 Remote Mounting. A mounting clip is packaged with each
receiver. To install the receiver, attach the clip to the mounting
surface with screws. Position the two rectangular holes on the
back of the receiver over the clip and snap the receiver down into
place.
MOUNTING CLIP

RECEIVER

MOUNTING HOLES
ON RECEIVER
MOUNTING
CLIP

(1) COM

MODEL 524
TRANSFORMER

MANUAL
PUSHBUTTON

MANUAL
PUSHBUTTON

LINEAR LIMITED WARRANTY

IMPORTANT !!!

This product is warranted to the consumer against defects in material
and workmanship for one year from the date of purchase. This
warranty applies to first retail buyers of new devices. Warrantor will
repair, or at its option, replace, any device it finds that requires service
under this warranty, and will return the repaired or replaced device to
the consumer at the warrantor’s cost. For warranty service and
shipping instructions contact warrantor at the phone number shown
below. Devices must be sent to warrantor for service at owner’s
expense. The remedies provided by this warranty are exclusive.
Implied warranties under state law are to the one year period of this
written warranty. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you.
In order to be protected by this warranty, save your proof of purchase
and send copy with equipment should repair be required. This
warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.

Linear radio controls provide a reliable communications link and fill an
important need in portable wireless signaling. However, there are
some limitations which must be observed.

All products returned for warranty service require a Return
Product Authorization Number (RPA#). Contact Linear
Technical Services at 1-800-421-1587 for an RPA# and other
important details.

✶ For U.S. installations only: The radios are required to comply with FCC Rules

✶

✶
✶
✶

and Regulations as Part 15 devices. As such, they have limited transmitter
power and therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and
may be blocked by radio signals that occur on or near their operating
frequencies, regardless of code settings.
Changes or modifications to the device may void FCC compliance.
Infrequently used radio links should be tested regularly to protect against
undetected interference or fault.
A general knowledge of radio and its vagaries should be gained prior to acting
as a wholesale distributor or dealer, and these facts should be communicated
to the ultimate users.

This device complies with FCC Rules Part 15 and IC Canada Rules
and Regulations. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and (2) this device
must accept any interference received, including interference that
may cause undesired operation.
Copyright © 1999 Linear Corporation

200108 E



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 1999:08:20 13:14:23Z
Subject                         : INSTR,CODE SET,DELTA-3
Modify Date                     : 2001:01:31 12:24:37-08:00
Page Count                      : 1
Creation Date                   : 1999:08:20 13:14:23Z
Producer                        : Acrobat Distiller 3.01 for Windows
Author                          : COPYRIGHT © 1999 LINEAR CORPORATION
Mod Date                        : 2001:01:31 12:24:37-08:00
Creator                         : COPYRIGHT © 1999 LINEAR CORPORATION
Title                           : Ventura - 200108E.CHP
Description                     : INSTR,CODE SET,DELTA-3

EXIF Metadata provided by EXIF.tools