Linear Mini T 1 Channel Key Ring Transmitter Quick Start Guide Ventura 106914D.CHP

: Linear Linear-Mini-T-1-Channel-Key-Ring-Transmitter-Quick-Start-Guide linear-mini-t-1-channel-key-ring-transmitter-quick-start-guide linear pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

FCC ID: EF4 793 DNT00026
This device complies with FCC Rules Part 15. Operation is subject
to the following two conditions: (1) This device may not cause
harmful interference and (2) This device must accept any
interference received, including interference that may cause
undesired operation.

LIMITED WARRANTY
This product is warranted to the consumer against defects in
material and workmanship for one year from the date of purchase.
This warranty applies to first retail buyers of new devices. Warrantor
will repair, or at its option, replace, any device it finds that requires
service under this warranty, and will return the repaired or replaced
device to the consumer at the warrantor’s cost. For warranty service
and shipping instructions contact warrantor at the address shown
below. Devices must be sent to warrantor for service at owner’s
expense. The remedies provided by this warranty are exclusive.
Implied warranties under state law are to the one year period of this
written warranty. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitation may not apply to
you. In order to be protected by this warranty, save your proof of
purchase and send copy with equipment should repair be required.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.

Delta-3 Series

miniTransmitter
Digital Transmitter
Code Setting Instructions

All products returned for warranty service require a Return
Product Authorization Number (RPA#). Contact Linear Technical
Services at 1-800-421-1587 for an RPA# and other important
details.

5.500"

NOTE: If the transmitter fails to activate
the receiver, first check the coding
switches in the receiver to make sure that
the receiver’s digital code system
matches that of the miniTransmitter. Next
check the battery and replace it if it is
weak. Although the battery should last for
two years with normal use, it is good
practice to install a new battery every
year. A slowly flashing or steadily lit LED
on the transmitter indicates that the
battery is too low for transmission to
occur. A rapidly flickering light during
transmission indicates that the unit is
operating properly.

IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill
an important need in portable wireless signaling. However, there are
some limitations which must be observed.
* For U.S. installations only: The radios are required to comply
with FCC Rules and Regulations as Part 15 devices. As such,
they have limited transmitter power and therefore limited
range.
* A receiver cannot respond to more than one transmitted signal
at a time and may be blocked by radio signals that occur on or
near their operating frequencies, regardless of code settings.
* Changes or modifications to the device may void FCC compliance.
* Infrequently used radio links should be tested regularly to
protect against undetected interference or fault.
* A general knowledge of radio and its vagaries should be gained
prior to acting as a wholesale distributor or dealer, and these
facts should be communicated to the ultimate users.

Copyright © 1999 Linear Corporation

8.500"

INSTR,CODE SET,MINI XMTR
Linear P/N: 106914 D
Material: 20 Lb.Mead Bond
Ink: Black
Side 1 of 2
Scale: 1-1

106914 D

(800) 421-1587 • www.linearcorp.com

In addition, among the 256 valid codes
available, four should not be used
because they are too often duplicated.
These codes are (1) all ON; (2) all OFF;
(3) alternating ON/OFF; (4) alternating
OFF/ON.
CODE SWITCH LOCATION
Remove the battery cover and battery
( s e e F i g u r e 1 ) , t o a c c es s t he
miniTransmitter’s toggle coding switch
(see Figure 2).
SWITCHES 1, 4,
AND 7 ARE ON

8

TWIST LOOPS
TO REMOVE
DOOR
1
Figure 2: Toggle Coding Switch

REMOVE BATTERY
TO ACCESS CODE
SWITCH
Figure 1: Coding Switch Location

CODE SETTING
The coding is performed simply by using
a paper clip or similarly pointed object
(not a pencil or pen) to flip the eight
switches to On or OFF position. A toggle
switch set to the system code 1, 4, 7 ON
appears in Figure 2.

8.500"

INSTR,CODE SET,MINI XMTR
Linear P/N: 106914 D
Material: 20 Lb. Mead Bond
Ink: Black
Side 2 of 2
Scale: 1-1

Reinstall battery observing polarity.
Replace battery cover.
CHECK-OUT AND TEST
After matching the digital code set in the
transmitter to the receiver code, test the
system.
CAUTION: Be sure the door or gate is
in sight and the area is clear prior to
testing.
To test the transmitter, perform the
following steps.
Step 1: Move at least 6 feet away from
the receiver and push the miniTransmitter
button. Receiver activation indicates that
the transmitter is operating properly and
that the transmitter/ receiver’s digital codes
are correctly matched.
NOTE: The miniTransmitter transmits
continuously while the button is held
down, terminating when the button is
released.
Step 2: Operate the transmitter from
various locations within the area where it
will be used. This will help to locate
possible null areas where structural steel,
and/or certain appliances may interfere
with transmission.

5.500"

DESCRIPTION
The miniTransmitter is one of the smallest
portable signaling units manufactured by
Linear. This wireless transmitter owes its
miniature size to state-of-the-art circuit
technology. Only 5/8 inches thick, the
miniTransmitter measures 1-3/8 inches
wide by 1-7/8 inches high. It is compatible
with all Linear standard digital receivers.
CHOOSING A CODE
To code the miniTransmitter with the
receiver it operates, set the eight-digit
system code to the precise digital system
code set in the receiver. Do not retain the
original factory-set code.



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 1999:08:20 10:39:49
Producer                        : Acrobat Distiller 3.01 for Windows
Author                          : COPYRIGHT © 1999 LINEAR CORPORATION
Creator                         : ADOBEPS4.DRV Version 4.10
Title                           : Ventura - 106914D.CHP
Subject                         : INSTR,CODE SET,MINI XMTR
Modify Date                     : 2001:01:31 12:34:24-08:00
Page Count                      : 2

EXIF Metadata provided by EXIF.tools